(VENT-FREE) NATURAL GAS
STOVE HEATER
OWNER’S OPERATION AND INSTALLATION MANUAL
Model SL30NT Series Thermostat Control Gas Log Heater
(Burner System For Cast Iron Stoves)
SL30NT
Patent Pending
WARNING: The SL30NT series vent-free gas
log heater is only approved for use in the
Comfort Glowseries cast iron stove models
CISC and CISG.
WARNING: If the information in this
manual is not followed exactly, a fire or
explosion may result causing property
damage, personal injury, or loss of life.
— Do not store or use gasoline or other
WARNING:Improperinstallation,adjust-
flammable vapors and liquids in the
ment,alteration,service,ormaintenance
vicinityofthisoranyotherappliance.
can cause injury or property damage.
Refer to this manual for correct installa-
tion and operational procedures. For
assistance or additional information
consult a qualified installer, service
agency, or the gas supplier.
— WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
•
Do not touch any electrical
switch; do not use any phone in
your building.
• Immediately call your gas supplier
from a neighbor’s phone. Follow the
gas supplier’s instructions.
• If you cannot reach your gas sup-
plier, call the fire department.
— Installation and service must be per-
formed by a qualified installer, ser-
vice agency, or the gas supplier.
WARNING: This is an unvented gas-
fired heater. It uses air (oxygen) from
the room in which it is installed. Provi-
sionsforadequatecombustionandven-
tilation air must be provided. Refer to
AirforCombustionandVentilationsec-
tion on page 4 of this manual.
This appliance may be installed in an aftermarket*, permanently located, manufactured
(mobile) home, where not prohibited by local codes.
This appliance is only for use with the type of gas indicated on the rating plate.
This appliance is not convertible for use with other gases.
* Aftermarket: Completion of sale, not for purpose of resale, from the manufacturer
Save this manual for future reference.
Download from Www.Somanuals.com. All Manuals Search And Download.
OWNER’S MANUAL
PRODUCT
PRODUCT
FEATURES
IDENTIFICATION
OPERATION
This heater is clean burning. It requires no
outside venting. There is no heat loss out a
vent or up a chimney. Heat is generated by
realistic,dancingyellowflames.Thisheater
is designed for vent-free operation. State
and local codes in some areas prohibit the
Stove Body
One Piece
Log Set
use of vent-free heaters.
Inside Stove
Cavity
SAFETY PILOT
This heater has a pilot with an Oxygen
Depletion Sensing (ODS) safety shutoff
system. The ODS/pilot is a required feature
for vent-free room heaters. The ODS/pilot
shuts off the heater if there is not enough
fresh air.
PIEZO IGNITION SYSTEM
This heater has a piezo ignitor. This system
requires no matches, batteries, or other
sources to light heater.
Piezo Ignitor
Control Knob
Gas Log Heater
Base Assembly
Stove Door
(Shown in the
open position)
Figure 1 - Typical Stove Cabinet Model with Comfort Glow Gas Log Heater
LOCAL CODES
Install and use heater with care. Follow all
localcodes. Intheabsenceoflocalcodes, use
the latest edition of The National Fuel Gas
Code ANSI Z223.1/NFPA 54*.
*Available from:
American National Standards Institute, Inc.
1430 Broadway
New York, NY 10018
National Fire Protection Association, Inc.
Batterymarch Park
Quincy, MA 02269
104463
3
Download from Www.Somanuals.com. All Manuals Search And Download.
VENT-FREE NATURAL GAS STOVE HEATER
Confined and Unconfined Space
PROVIDING ADEQUATE
VENTILATION
AIR FOR
The National Fuel Gas Code ANSI Z223.1/
NFPA 54 defines a confined space as a
space whose volume is less than 50 cubic
feet per 1,000 Btu per hour (4.8 m3 per kw)
of the aggregate input rating of all appli-
ances installed in that space and an uncon-
fined space as a space whose volume is not
less than 50 cubic feet per 1,000 Btu per
hour (4.8 m3 per kw) of the aggregate input
rating of all appliances installed in that
space. Rooms communicating directly with
the space in which the appliances are in-
stalled*, through openings not furnished
with doors, are considered a part of the
unconfined space.
COMBUSTION AND
VENTILATION
The following are excerpts from Na-
tional Fuel Gas Code, ANSI Z223.1/
NFPA 54, Section 5.3, Air for Combus-
tion and Ventilation.
WARNING: This heater shall
not be installed in a confined
space or unusually tight con-
struction unless provisions are
provided for adequate combus-
tion and ventilation air. Read
the following instructions to in-
sure proper fresh air for this
and other fuel-burning appli-
ances in your home.
All spaces in homes fall into one of the three
following ventilation classifications:
1. Unusually Tight Construction
2. Unconfined Space
3. Confined Space
The information on pages 4 through 6 will
help you classify your space and provide
adequate ventilation.
* Adjoining rooms are communicating only
iftherearedoorlesspassagewaysorventila-
tion grills between them.
Unusually Tight Construction
Today’s homes are built more energy effi-
cient than ever. New materials, increased
insulation, and new construction methods
helpreduceheatlossinhomes.Homeowners
weather strip and caulk around windows and
doorstokeepthecoldairoutandthewarmair
in. During heating months, home owners
want their homes as airtight as possible.
The air that leaks around doors and win-
dows may provide enough fresh air for
combustion and ventilation. However, in
buildings of unusually tight construction,
you must provide additional fresh air.
Unusually tight construction is de-
fined as construction where:
While it is good to make your home energy
efficient, your home needs to breathe. Fresh
air must enter your home. All fuel-burning
appliances need fresh air for proper com-
bustion and ventilation.
a. walls and ceilings exposed to the
outside atmosphere have a con-
tinuous water vapor retarder with
a rating of one perm (6 x 10-11 kg
per pa-sec-m2) or less with open-
ings gasketed or sealed and
Exhaustfans, fireplaces, clothesdryers, and
fuel burning appliances draw air from the
house to operate. You must provide ad-
equate fresh air for these appliances. This
will insure proper venting of vented fuel-
burning appliances.
b. weather stripping has been
added on openable windows and
doors and
c. caulking or sealants are applied
to areas such as joints around
window and door frames, be-
tween sole plates and floors, be-
tween wall-ceiling joints, be-
tween wall panels, at penetra-
tions for plumbing, electrical, and
gas lines, and at other openings.
If your home meets all of the three
criteria above, you must provide ad-
ditional fresh air. See Ventilation Air
From Outdoors, page 6.
If your home does not meet all of the
three criteria above, proceed to De-
termining Fresh-Air Flow For Heater
Location, page 5.
104463
4
Download from Www.Somanuals.com. All Manuals Search And Download.
OWNER’S MANUAL
AIR FOR
COMBUSTION AND
VENTILATION
Continued
DETERMINING FRESH-AIR FLOW FOR HEATER LOCATION
Determining if You Have a Confined or Unconfined Space
Use this work sheet to determine if you have a confined or unconfined space.
Space:Includestheroominwhichyouwillinstallheaterplusanyadjoiningroomswithdoorlesspassagewaysorventilationgrillsbetween
the rooms.
1. Determine the volume of the space (length x width x height).
Length x Width x Height = ____________________ cu. ft. (volume of space)
Example: Space size 20 ft. (length) x 16 ft. (width) x 8 ft. (ceiling height) =2560 cu. ft. (volume of space)
If additional ventilation to adjoining room is supplied with grills or openings, add the volume of these rooms to the total volume of
the space.
2. Multiply the space volume by 20 to determine the maximum Btu/Hr the space can support.
_________________ (volume of space) x 20 = (maximum Btu/Hr the space can support)
Example: 2560 cu. ft. (volume of space) x 20 = 51,200 (maximum Btu/Hr the space can support)
3. Add the Btu/Hr of all fuel burning appliances in the space.
Vent-free heater
Gas water heater*
Gas furnace
____________________Btu/Hr
____________________Btu/Hr
____________________Btu/Hr
____________________Btu/Hr
____________________Btu/Hr
Example:
Gas water heater
40,000
Btu/Hr
Btu/Hr
Btu/Hr
Vented gas heater
Gas fireplace logs
Vent-free heater + 30,000
Total 70,000
=
Other gas appliances* + ___________________Btu/Hr
Total = ___________________Btu/Hr
* Do not include direct-vent gas appliances. Direct-vent draws combustion air from the outdoors and vents to the outdoors.
4. Compare the maximum Btu/Hr the space can support with the actual amount of Btu/Hr used.
_________________ Btu/Hr (maximum the space can support)
_________________ Btu/Hr (actual amount of Btu/Hr used)
Example: 51,200 Btu/Hr (maximum the space can support)
70,000 Btu/Hr (actual amount of Btu/Hr used)
The space in the above example is a confined space because the actual Btu/Hr used is more than the maximum Btu/Hr the space cansupport.
You must provide additional fresh air. Your options are as follows:
A. Rework worksheet, adding the space of an adjoining room. If the extra space provides an unconfined space, remove door to adjoin-
ing room or add ventilation grills between rooms. See Ventilation Air From Inside Building, page 6.
B. Vent room directly to the outdoors. See Ventilation Air From Outdoors, page 6.
C. Install a lower Btu/Hr heater, if lower Btu/Hr size makes room unconfined.
If the actual Btu/Hr used is less than the maximum Btu/Hr the space can support, the space is an unconfined space. You will need no
additional fresh air ventilation.
WARNING: If the area in which the heater may be operated is smaller than that defined as an unconfined space
or if the building is of unusually tight construction, provide adequate combustion and ventilation air by one of
themethodsdescribedintheNationalFuelGasCode,ANSIZ223.1/NFPA54,Section5.3orapplicablelocalcodes.
Continued
104463
5
Download from Www.Somanuals.com. All Manuals Search And Download.
VENT-FREE NATURAL GAS STOVE HEATER
AIR FOR
COMBUSTION AND
12"
VENTILATION
Continued
Ventilation
Ventilation Grills
Into Adjoining Room,
Option 2
Grills
Into Adjoining
Room,
VENTILATION AIR
Or
Ventilation Air From Inside
Building
Remove
Door into
Adjoining
Room,
Option
3
Option 1
Thisfreshairwouldcomefromanadjoining
unconfined space. When ventilating to an
adjoining unconfined space, you must pro-
vide two permanent openings: one within
12" of the ceiling and one within 12" of the
floor on the wall connecting the two spaces
(see options 1 and 2, Figure 2). You can also
remove door into adjoining room (see op-
tion 3, Figure 2). Follow the National Fuel
Gas Code, ANSI Z223.1/NFPA 54, Section
5.3, Air for Combustion and Ventilation for
required size of ventilation grills or ducts.
12"
Ventilation Air From Outdoors
Provide extra fresh air by using ventilation
grills or ducts. You must provide two per-
manent openings: one within 12" of the
ceiling and one within 12" of the floor.
Connect these items directly to the outdoors
orspacesopentotheoutdoors.Thesespaces
include attics and crawl spaces. Follow the
National Fuel Gas Code, ANSI Z223.1/
NFPA 54, Section 5.3, Air for Combustion
and Ventilation for required size of ventila-
tion grills or ducts.
Figure 2 - Ventilation Air from Inside Building
Ventilated
Outlet
Attic
Air
Outlet
Air
To Attic
IMPORTANT: Do not provide openings
for inlet or outlet air into attic if attic has
a thermostat-controlled power vent.
Heated air entering the attic will activate
the power vent.
To
Crawl
Space
Inlet
Air
Ventilated
Crawl Space
Inlet Air
Figure 3 - Ventilation Air from Outdoors
104463
6
Download from Www.Somanuals.com. All Manuals Search And Download.
OWNER’S MANUAL
IMPORTANT:Vent-freeheatersaddmois- Carefullyfollowtheinstructionsbelow.This
ture to the air. Although this is beneficial, stove is a freestanding unit designed to set
installing heater in rooms without enough directly on the floor. IMPORTANT: You
ventilation air may cause mildew to form must maintain minimum wall and ceiling
from too much moisture. See Air for Com- clearances during installation. The mini-
bustion and Ventilation, pages 4 through 6. mum clearances are shown in Figure 4.
INSTALLATION
NOTICE: This heater is intended
foruseassupplementalheat.Use
this heater along with your pri-
mary heating system. Do not in-
stall this heater as your primary
heat source. If you have a central
heating system, you may run
system’scirculatingblowerwhile
using heater. This will help circu-
late the heat throughout the
house. In the event of a power
outage, you can use this heater
as your primary heat source.
Measure from outermost point of stove top.
CHECK GAS TYPE
Minimum Wall and Ceiling
Clearances (see Figure 4)
Use only natural gas. If your gas supply is
not natural gas, do not install heater. Call
A. Clearances from outermost point of
stove top to any combustible side wall
should not be less than 12 inches.
dealer where you bought heater for proper
type heater.
CLEARANCES TO
COMBUSTIBLES
(Vent-Free Operation Only)
B. Clearances from outermost point of
stove top to any combustible back wall
should not be less than 6 inches (In-
cludes Corner Installations).
WARNING: A qualified ser-
vice person must install heater.
Follow all local codes.
C. Clearances from the stove top to the
ceiling should not be less than 48
inches.
WARNING:Maintainthemini-
mum clearances. If you can, pro-
vide greater clearances from
floor, ceiling, and adjoining side
and back walls.
NOTICE:Stateorlocalcodesmay
onlyallowoperationofthisappli-
ance in a vented configuration.
Check your state or local codes.
Ceiling
Front View
48"
Minimum
WARNING: Never install the
heater
12"
Minimum
12"
Minimum
Side Wall
Side Wall
• in a bedroom or bathroom
• in a recreational vehicle
• where curtains, furniture,
clothing, or other flammable
objectsarelessthan42inches
from the front, top, or sides of
the heater
Top View
Back Wall
• in high traffic areas
• in windy or drafty areas
6
"
Minimum
Side View
CAUTION: This heater cre-
ates warm air currents. These
currents move heat to wall sur-
faces next to heater. Installing
heater next to vinyl or cloth wall
coverings or operating heater
where impurities (such as, but
not limited to, tobacco smoke,
aromatic candles, cleaning flu-
ids,oilorkerosenelamps,etc.)in
the air exist, may discolor walls
or cause odors.
Ceiling
12
"
12
"
Minimum
Minimum
Side Wall
Corner
Side Wall
48"
Minimum
Wall
Back Wall
6"
Minimum
6
"
Minimum
Front of
Stove Unit
6
"
Wall
Minimum
Floor
Figure 4 - Minimum Clearance to Walls and Ceiling (Stove May Vary Depending on
Model)
Continued
104463
7
Download from Www.Somanuals.com. All Manuals Search And Download.
VENT-FREE NATURAL GAS STOVE HEATER
INSTALLATION
Continued
Bolt
STOVE CAVITY ASSEMBLY
1. Lift off corrugated box enclosing stove
body crating.
2. Remove all screws fastening the wood
frame enclosure. Spread wood frame
open and lift away from plastic-bagged
Product
Identification Label
Figure 5 - Removing Back Panel
Back Stove Panel
stove body. The bottom pieces of pal-
let wood will remain bolted to the stove
body.
Top of Stove Unit
3. Remove plastic bag from stove body.
4. Remove back panel from stove (see
Figure 5). Use an adjustable wrench or
a 10 mm socket. Remove six (6) bolts
and washers. Keep bolts and washers
to reattach back panel later.
Front of
Stove Unit
Top of
Stove
Unit
Front of
Stove Unit
5. Remove all contents from inside stove
cavity. Contents include:
Pallet Wood
Bolted to
Stove Body
Bottom
(1) - Stove bottom
Drop Cloth/
Blanket
(4) - Legs (Amity models include leg
leveler bolts)
(1) - Bottom door
(1) - Top grate
(1) - Hardware kit bag with fasteners
Figure 6 - Laying Down Stove On Back (Stove Style May Vary Depending on Model)
6. Carefully lay stove body on back to
attach bottom components to stove
body (see Figure 6). Rest stove on drop
cloth or blanket to avoid scratching
stove edges.
Front
Pallet
Wood
Bolt
7. Remove remaining pallet wood at-
tached to bottom of stove body (see
Figure 7). Use an adjustable wrench to
remove bolts.
Bottom Of
Stove Unit
Pallet
Wood
8. Fasten each leg to stove with four (4)
bolts. Use a flat screw driver to tighten
bolt to leg. Thread bolt in tapped holes
on stove body (see Figure 8 and Figure
9, page 9).
Figure 7 - Removing Pallet Wood From The Bottom of The Stove
Door Hinge Step
Bolt Hole
Door Catch Bolt
With Adjustable
Hex Nuts Hole
Front
Leg
Hole
Leg
Hole
Bottom Of
Stove Unit
Stove
Bottom
Holes
Leg
Hole
Leg
Hole
Figure 8 - Locating Threaded Holes for Stove Bottom, Legs, and Door Attachment
(Appearance May Vary Depending on Model)
104463
8
Download from Www.Somanuals.com. All Manuals Search And Download.
OWNER’S MANUAL
INSTALLATION
Continued
9. Fasten stove bottom to stove with four
(4) M6 x 1 - 25mm bolts. Use a flat
washer and lock washer with each bolt.
Tighten bolts into threaded holes on
stove body (see Figure 8, page 8 and
10). Use an adjustable wrench or a
10mm socket.
Washers
Bolt
Bottom Of
Bolt
10. Attach stove door by inserting step bolt
through door hinge pivot holes and into
threaded hole in stove body (see Fig-
ure 11). Use an adjustable wrench or a
12mm socket to fasten step bolt.
Tighten step bolt until snug. Make sure
door moves freely.
Stove Unit
Bottom Of
Stove Unit
Stove
Bottom
Leg
Figure 9 - Attaching Stove Legs
Figure 10 - Attaching Stove Bottom
11. Install door catch bolt (M8 x 1.25-
55mm with two M8 hex nuts) into
threaded hole on stove body (see Fig-
ure 8, page 8). Use an adjustable
wrench or a 12mm socket. The catch
bolt has two hex nuts attached to it (see
Figure 12). The top nut is a bolt stop
and the bottom nut is for door leveling
adjustment.
Stove
Door
Stove
Door
Bolt
Shoulder
Threaded
Hole
Door
Hinge
Door
Hinge
12. Check general catch bolt alignment
with door claw. Make final adjustment
and door leveling after stove is in nor-
mal standing position.
13. Carefully lift stove back up on its four
attached legs.
Step
Bolt
Step
Bolt
14. If available, install gas log heater in-
side stove cavity before installing the
back panel (see Installing Gas Log
Heater Into Stove, page 10).
Bolt
Shoulder
Stove Bottom
Figure 11 - Attaching Stove Door (Appearance May Vary Depending on Model)
15. Fasten back panel to stove with six (6)
M6 x 1 - 20mm bolts and washers.
Make sure product identification label
is located on the outside in lower left-
hand corner.
Bolt Stop
Adjusting Nut
Door
Door Claw
Catch Bolt
Figure 12 - Catch Bolt and Door Claw Orientation
Continued
104463
9
Download from Www.Somanuals.com. All Manuals Search And Download.
VENT-FREE NATURAL GAS STOVE HEATER
7. Fasten heater base to stove bottom with
#10-24 x .50 bolts and hex nuts pro-
vided with gas log heater (see Figure
14). Attachment hardware is factory
packed inside plastic bag with installa-
tion manual and owner’s registration
card. Push bolt through heater base
mounting hole and through stove bot-
tom. Connect hex nut to bolt on under-
side of stove bottom. The bolt hex head
is for a 5/16" socket and the hex nuts
are for a 3/8" socket. If sockets are not
available, use adjustable wrenches.
Heater
Base
INSTALLATION
Bolt
Continued
INSTALLING GAS LOG
HEATER INTO STOVE
1. Remove log and gas log heater from
carton. Note: Do not pick up gas log
heater by the burner itself. This could
damage heater. Always handle the gas
log heater by the heater base only.
Stove
Bottom
Hex Nut
Figure 14 - Fastening Heater Base to
Stove Drop Bottom
2. Remove all protective packaging applied
to log and gas log heater for shipment.
8. Set one-piece log on heater base as
shown in Figure 15. Make sure middle
section at bottom of log is seated into
"U" shaped cutout in center of heater
base. Log will fit securely on base.
IMPORTANT: Make sure log does not
cover any burner ports and does not
touch the stove cavity (see Figure 16).
3. Check all items for any shipping dam-
age. If damaged, promptly inform
dealer where you bought heater.
One-Piece
Log Set
4. If not already removed, remove back
panel from assembled stove body (see
Figure 5, page 8). Use an adjustable
wrench or a 10 mm socket. Remove six
(6) bolts and washers. Keep bolts and
washers to reattach back panel later.
Middle
9. Fasten back panel to stove with six (6)
M6 x 1.20mm bolts and washers. Make
sure product identification label is lo-
cated on the outside lower left-hand
corner.
Section at
Bottom of
Log Set
5. Set gas log heater inside stove (see Fig-
ure 13). Make sure control knob exten-
sions pass through bottom front opening.
Burner
6. Align outside holes on heater base with
four (4) mounting holes on the stove
bottom (see Figure 13).
10. Place freestanding stove in desired po-
sition in room. Be sure to maintain
clearances to combustibles as outlined
on page 7.
LO
H I
"U" Shaped
Cutout in
Chassis
Heater
Base
Figure 15 - Installing One-Piece Stove
Log Set
Burner
Burner Porting Areas
(double slotted
rectangular openings
Bottom
Front
Opening
Bolt
Stove
Heater
Bottom
Base
Figure 13 - Placing Heater Base In Stove Cavity (Appearance May Vary Depending on
Model)
One-Piece
Log Set
Safety Pilot Location
Figure 16 - Top View of One-Piece Log
Set on Gas Log Heater
104463
10
Download from Www.Somanuals.com. All Manuals Search And Download.
OWNER’S MANUAL
Installationmustincludeaequipmentshutoff Check your building codes for any special
valve, union, and plugged 1/8" NPT tap. requirementsforlocatingequipmentshutoff
Locate NPT tap within reach for test gauge valve to fireplaces.
INSTALLATION
Continued
hook up. NPT tap must be upstream from
ApplypipejointsealantlightlytomaleNPT
heater (see Figure 18).
CONNECTING TO GAS
SUPPLY
threads. This will prevent excess sealant
IMPORTANT: Install equipment shutoff from going into pipe. Excess sealant in pipe
valve in an accessible location. The equip- could result in clogged heater valves.
ment shutoff valve is for turning on or
WARNING: This appliance re-
quires a 1/2" NPT (National Pipe
Thread) inlet connection to the
pressure regulator.
shutting off the gas to the appliance.
WARNING:Usepipejointseal-
ant that is resistant to liquid pe-
Back Stove
Panel
troleum (LP) gas.
WARNING: A qualified service
personmustconnectheatertogas
supply. Follow all local codes.
We recommend that you install a sediment
trap in supply line as shown in Figure 18.
Locate sediment trap where it is within reach
for cleaning. Install in piping system between
fuel supply and heater. Locate sediment trap
where trapped matter is not likely to freeze. A
sediment trap traps moisture and contami-
nants. This keeps them from going into heater
controls. If sediment trap is not installed or is
installed wrong, heater may not run properly.
Product
Identification
Label
Back View
Installation Items Needed
Beforeinstallingheater,makesureyouhave
the items listed below.
• piping (check local codes)
• sealant (resistant to propane/LP gas)
• equipment shutoff valve *
• test gauge connection *
• sediment trap
Side View
Gas Log
Heater
Front
of
Stove
Unit
Gas Inlet
Connection
Access
• tee joint
• pipe wrench
CAUTION: Avoid damage to
regulator.Holdgasregulatorwith
wrenchwhenconnectingittogas
piping and/or fittings.
* ACSAdesign-certifiedequipmentshutoff
valve with 1/8" NPT tap is an acceptable
alternative to test gauge connection. Pur-
chase the optional CSA design-certified
equipment shutoff valve from your dealer.
See Accessories, page 19.
Figure 17 - Gas Regulator Location and
Gas Line Access Into Stove Cabinet
CSA Design-Certified
Equipment Shutoff Valve
With 1/8" NPT Tap*
Thegasinletconnectionforthestoveheater
islocatedonthelowerright-handsideofthe
stove when viewed from the front of the
unit. The gas connection can be made either
through the bottom right side or through the
lower back opening as illustrated in Figure
17. Make sure gas log heater is secured to
the stove cavity assembly.
From Gas Meter
(5" W.C.** to 10.5"
W.C. Pressure)
Approved Flexible Gas Hose
(if allowed by local codes)
Gas
Regulator
Tee Joint
Sediment
Pipe
Trap
WARNING: Never connect
heater to private (non-utility) gas
wells. This gas is commonly
known as wellhead gas.
Nipple
3" Minimum
Cap
Figure 18 - Gas Connection
* Purchase the optional CSA design-certified equipment shutoff valve from your dealer.
CAUTION:Useonlynew,black
ironorsteelpipe.Internally-tinned
copper tubing may be used in
certain areas. Check your local
codes. Use pipe of 1/2" diameter
or greater to allow proper gas vol-
ume to heater. If pipe is too small,
undue loss of volume will occur.
See Accessories, page 19.
**Minimum inlet pressure for purpose of input adjustment.
Continued
104463
11
Download from Www.Somanuals.com. All Manuals Search And Download.
VENT-FREE NATURAL GAS STOVE HEATER
Test Pressures Equal To or Less Than
1/2 PSIG (3.5 kPa)
Pressure Testing Heater Gas
Connections
1. Open equipment shutoff valve (see
INSTALLATION
Continued
1. Close equipment shutoff valve (see
CHECKING GAS
CONNECTIONS
Figure 19).
Figure 19).
2. Pressurize supply piping system by
either using compressed air or open-
ing main gas valve located on or near
gas meter.
2. Open main gas valve located on or near
gas meter.
WARNING: Test all gas pip-
3. Make sure control knob of heater is in
the OFF position.
ing and connections for leaks
after installing or servicing. Cor-
rect all leaks at once.
3. Check all joints from gas meter to
equipment shutoff valve (see Figure
19).Apply noncorrosive leak detection
fluid to gas joints. Bubbles forming
show a leak.
4. Check all joints from equipment
shutoff valve to control valve (see Fig-
ure 20). Apply noncorrosive leak de-
tection fluid to gas joints. Bubbles
forming show a leak.
WARNING: Never use an
open flame to check for a leak.
Apply a noncorrosive leak de-
tectionfluidtoalljoints.Bubbles
forming show a leak. Correct all
leaks at once.
4. Correct all leaks at once.
5. Correct all leaks at once.
Open
6. Light heater (see Operating Heater,
page 13). Check all other internal joints
for leaks.
Equipment
Shutoff
Valve
7. Turn off heater (see To Turn Off Gas to
Appliance, page 13).
Pressure Testing Gas Supply
Piping System
Closed
Test Pressures In Excess Of 1/2 PSIG
(3.5 kPa)
Figure 19 - Equipment Shutoff Valve
1. Disconnect appliance with its appliance
main gas valve (control valve) and equip-
ment shutoff valve from gas supply pip-
ing system. Pressures in excess of 1/2
psig will damage heater regulator.
2. Cap off open end of gas pipe where
equipment shutoff valve was
connected.
Equipment
Shutoff
Valve
3. Pressurize supply piping system by
either using compressed air or open-
ing main gas valve located on or near
gas meter.
Gas Meter
4. Check all joints of gas supply piping
system.Apply noncorrosive leak detec-
tion fluid to gas joints. Bubbles form-
ing show a leak.
Control Valve Location
5. Correct all leaks at once.
6. Reconnect heater and equipment
shutoff valve to gas supply. Check re-
connected fittings for leaks.
Figure 20 - Checking Gas Joints
104463
12
Download from Www.Somanuals.com. All Manuals Search And Download.
OWNER’S MANUAL
7. Keep control knob pressed in for 30
seconds after lighting pilot. After 30
seconds, release control knob.
LIGHTING
OPERATING
HEATER
INSTRUCTIONS
• If control knob does not pop out
NOTICE: During initial operation
of new heater, burning logs will
give off a paper-burning smell.
Orangeflamewillalsobepresent.
This will only last a few hours.
FOR YOUR SAFETY
when released, contact a qualified
service person or gas supplier for
repairs.
READ BEFORE
LIGHTING
Note: If pilot goes out, repeat steps
3 through 7. This heater has a safety
interlock system. Wait one (1) minute
for system to reset before lighting
pilot again.
WARNING: If you do not fol-
low these instructions exactly, a
fireorexplosionmayresultcaus-
ing property damage, personal
injury or loss of life.
1. STOP! Read the safety information,
column 1.
2. Make sure equipment shutoff valve
is fully open.
8. Turn control knob counterclockwise
C-clockwise
to desired heating level. The
A. This appliance has a pilot which must 3. Turn control knob clockwise
burners should light. Set control knob
to any heat level between HI and LO.
be lighted by hand. When lighting the
pilot, follow these instructions exactly.
to the OFF position.
4. Wait five (5) minutes to clear out any
gas. Then smell for gas, including
near the floor. If you smell gas,
STOP! Follow “B” in the safety in-
formation, column 1. If you don’t
smell gas, go to the next step.
B. BEFORE LIGHTING smell all
around the appliance area for gas. Be
sure to smell next to the floor because
some gas is heavier than air and will
settle on the floor.
Pilot Burner
Thermocouple
WHAT TO DO IF YOU SMELL 5. Turn control knob counterclockwise
GAS
to the PILOT position.
C-clockwise
• Do not try to light any appliance.
• Do not touch any electric switch; do
not use any phone in your building.
• Immediately call your gas supplier
from a neighbor’s phone. Follow
the gas supplier’s instructions.
• If you cannot reach your gas sup-
plier, call the fire department.
Press in control knob for five (5) sec-
onds (see Figure 21).
Figure 22 - Pilot
Note: You may be running this
heater for the first time after hook-
ing up to gas supply. If so, the con-
trol knob may need to be pressed in
for 30 seconds or more. This will al-
low air to bleed from the gas system.
TO TURN OFF GAS
TO APPLIANCE
Shutting Off Heater
Turn control knob clockwise
the OFF position.
to
C. Use only your hand to push in or turn
the gas control knob. Never use tools.
If the knob will not push in or turn
by hand, don’t try to repair it, call a
qualified service technician or gas
supplier. Force or attempted repair
may result in a fire or explosion.
6. With control knob pressed in, press
and release ignitor button. This will
light pilot. The pilot is attached to the
front burner. If needed, keep press-
ing ignitor button until pilot lights.
Shutting Off Burners Only (pilot
stays lit)
Turn control knob clockwise
the PILOT position.
to
Note: If pilot does not stay lit, con-
tact a qualified service person or gas
supplier for repairs. Until repairs are
made, light pilot with match. To light
pilot with match, see Manual Light-
ing Procedure on page 14.
D. Do not use this appliance if any part
has been under water. Immediately call
a qualified service technician to inspect
the appliance and to replace any part
of the control system and any gas con-
trol which has been under water.
Control Knob
Ignitor Button
Figure 21- Control Knob and Ignitor
Button Location
104463
13
Download from Www.Somanuals.com. All Manuals Search And Download.
VENT-FREE NATURAL GAS STOVE HEATER
OPERATING
INSPECTING
SPECIFICATIONS
HEATER
BURNERS
Btu (Variable)
Type Gas
16,000/30,000
Continued
Check pilot flame pattern and burner flame
patterns often.
Natural Gas Only
Piezo
Ignition
THERMOSTAT
CONTROL
OPERATION
Pressure Manifold
3.5" W.C.
PILOT FLAME PATTERN
Inlet Gas Pressure (in. of water)
Figure 23 shows a correct pilot flame pat-
tern.Figure24showsanincorrectpilotflame
pattern.Theincorrectpilotflameisnottouch-
ing the thermocouple. This will cause the
thermocouple to cool. When the thermo-
couple cools, the heater will shut down.
Maximum
10.5"
Thethermostatcontrolknobcanbesetto
any comfort level between HI and LO.
The thermostat will gradually modulate
the heat output and flame height from
higher to lower settings, or pilot, in order
to maintain the comfort level you select.
The ideal comfort setting will vary by
householddependingupontheamountof
space to be heated, the output of the
central heating system, etc.
Minimum*
5"
Shipping Weight
* For input adjustment
28 lbs.
If pilot flame pattern is incorrect, as shown
in Figure 24
SERVICE HINTS
When Gas Pressure Is Too Low
• turn heater off (see To Turn Off Gas to
Appliance, page 13)
• pilot will not stay lit
• see Troubleshooting, pages 16 through 18
• burners will have delayed ignition
• heater will not produce specified heat
Note: Selecting the HI setting with the
control knob will cause the burner to
remainfullyon,withoutmodulatingdown
in most cases.
Note: The pilot flame on natural gas units
willhaveaslightcurve, butflameshouldbe
blue and have no yellow or orange color.
You may feel your gas pressure is too low.
Ifso, contactyourlocalnaturalgassupplier.
Pilot Burner
MANUAL LIGHTING
PROCEDURE
TECHNICAL
SERVICE
Thermocouple
1. Follow steps 1 through 5 under Light-
ing Instructions, page 13.
Youmayhavefurtherquestionsaboutinstal-
lation, operation, or troubleshooting. If so,
contactDESAInternational’sTechnicalSer-
vice Department at 1-866-672-6040. When
calling, please have your model and serial
numbers of your heater ready.
2. Depress control knob and light pilot
with match.
Figure 23 - Correct Pilot Flame Pattern
3. Keep control knob pressed in for 30
seconds after lighting pilot. After 30
seconds, release control knob. Now
follow step 8, Lighting Instructions,
page 13.
Pilot Burner
You can also visit DESA International’s
technical service web site at
Thermocouple
Figure 24 - Incorrect Pilot Flame Pattern
104463
14
Download from Www.Somanuals.com. All Manuals Search And Download.
OWNER’S MANUAL
4. Check the injector holder located at the
LOGS
CLEANING AND
MAINTENANCE
end of the burner tube again. Remove
any large particles of dust, dirt, lint, or
pet hair with a soft cloth or vacuum
cleaner nozzle.
• If you remove logs for cleaning, refer to
Installing Gas Log Heater into Stove,
page 10, to properly replace logs.
WARNING: Turn off heater
and let cool before cleaning.
• Replace log(s) if broken or chipped
(dime-sized or larger).
5. Blow air into the primary air holes on
the injector holder.
6. In case any large clumps of dust have MAIN BURNER
CAUTION: You must keep con-
trol areas, burner, and circulating
air passageways of heater clean.
Inspect these areas of heater be-
fore each use. Have heater in-
spected yearly by a qualified ser-
viceperson.Heatermayneedmore
frequentcleaningduetoexcessive
lint from carpeting, pet hair, bed-
ding material, etc.
now been pushed into the burner repeat
Periodically inspect all burner flame holes
steps 3 and 4.
with the heater running. All slotted burner
flame holes should be open with yellow
flame present. All round burner flame holes
should be open with a small blue flame
present. Some burner flame holes may be-
comeblockedbydebrisorrust,withnoflame
present. If so, turn off heater and let cool.
Remove blockage. Blocked burner flame
holes will create soot.
Clean the pilot assembly also. A yellow tip
on the pilot flame indicates dust and dirt in
the pilot assembly. There is a small pilot air
inlet hole about two inches from where the
pilot flame comes out of the pilot assembly
(see Figure 26). With the unit off, lightly
blow air through the air inlet hole. You may
blowthroughadrinkingstrawifcompressed
air is not available.
CLEANING BURNER
INJECTOR HOLDER AND
PILOT AIR INLET HOLE
Injector Holder
(May Be Brass
or Aluminum
Depending on
Burner
Tube
The primary air inlet holes allow the proper
amount of air to mix with the gas. This pro-
vides a clean burning flame. Keep these holes
clear of dust, dirt, lint, and pet hair. Clean
these air inlet holes prior to each heating
season. Blockedairholeswillcreatesoot. We
recommendthatyoucleantheuniteverythree
months during operation and have heater in-
spected yearly by a qualified service person.
Model)
Primary Air Inlet
Holes (Shape of
Holes May Vary
by Model)
Wealsorecommendthatyoukeeptheburner
tube and pilot assembly clean and free of
dustanddirt.Tocleanthesepartswerecom-
mend using compressed air no greater than
30 PSI. Your local computer store, hard-
ware store, or home center may carry com-
pressed air in a can. You can use a vacuum
cleaner in the blow position. If using com-
pressed air in a can, please follow the direc-
tions on the can. If you don't follow direc-
tionsonthe can, youcoulddamage the pilot
assembly. Note: Removing the rear panel
and top grates of your stove will make
cleaning easier.
Figure 25 - Injector Holder On Outlet
Burner Tube
Ports/Slots
Burner
Tube
Pilot
Assembly
Pilot Air
Inlet
Hole
1. Shut off the unit, including the pilot.
Allow the unit to cool for at least thirty
minutes.
2. Inspect burner, pilot, and primary air
inlet holes on injector holder for dust
and dirt (see Figure 25).
3. Blow air through the ports/slots and
holes in the burner.
Figure 26 - Pilot Inlet Air Hole
104463
15
Download from Www.Somanuals.com. All Manuals Search And Download.
VENT-FREE NATURAL GAS STOVE HEATER
TROUBLESHOOTING
Note: For additional help, visit DESA
International’stechnicalservicewebsite
WARNING: Turn off heater
andletcoolbeforeservicing.Only
aqualifiedservicepersonshould
service and repair heater.
CAUTION: Never use a wire,
needle, or similar object to clean
ODS/pilot.ThiscandamageODS/
pilot unit.
Note:Alltroubleshootingitemsarelistedin
order of operation.
OBSERVED PROBLEM
POSSIBLE CAUSE
REMEDY
When ignitor button is pressed, there is no
spark at ODS/pilot
1. Ignitor electrode not connected to igni- 1. Reconnect ignitor cable
tor cable
2. Ignitor cable pinched or wet
2. Free ignitor cable if pinched by any
metal or tubing. Keep ignitor cable dry
3. Replace ignitor cable
3. Broken ignitor cable
4. Bad piezo ignitor
4. Replace piezo ignitor
5. Ignitor electrode broken
6. Ignitor electrode positioned wrong
5. Replace pilot assembly
6. Replace pilot assembly
When ignitor button is pressed, there is
spark at ODS/pilot but no ignition
1. Gas supply turned off or equipment 1. Turn on gas supply or open equipment
shutoff valve closed
shutoff valve
2. Control knob not in PILOT position
2. Turn control knob to PILOT position
3. Control knob not pressed in while in 3. Press in control knob while in PILOT
PILOT position
position
4. Air in gas lines when installed
4. Continue holding down control knob.
Repeat igniting operation until air is re-
moved
5. ODS/pilot is clogged
5. Clean ODS/pilot (see Cleaning and
Maintenance, page 15) or replace ODS/
pilot assembly
6. Gas regulator setting is not correct
1. Control knob not fully pressed in
6. Replace gas control
ODS/pilot lights but flame goes out when
control knob is released
1. Press in control knob fully
2. Control knob not pressed in long enough 2. After ODS/pilot lights, keep control
knob pressed in 30 seconds
3. Equipment shutoff valve not fully open 3. Fully open equipment shutoff valve
4. Pilot flame not touching thermocouple, 4. A) Contact local natural gas company
which allows thermocouple to cool,
causing pilot flame to go out. This prob-
lem could be caused by one or both of
the following:
B) Clean ODS/pilot (see Cleaning and
Maintenance, page 15) or replace ODS/
pilot assembly
A) Low gas pressure
B) Dirty or partially clogged ODS/pilot
5. Thermocouple connection loose at con- 5. Hand tighten until snug, then tighten
trol valve
1/4 turn more
6. Thermocouple damaged
6. Replace pilot assembly
7. Control valve damaged
7. Replace control valve
104463
16
Download from Www.Somanuals.com. All Manuals Search And Download.
OWNER’S MANUAL
TROUBLESHOOTING
Continued
OBSERVED PROBLEM
POSSIBLE CAUSE
REMEDY
Burner does not light after ODS/pilot is lit
1. Burner orifice clogged
1. Clean burner (see Cleaning and Mainte-
nance, page 15) or replace burner orifice
2. Contact local natural gas company
2. Inlet gas pressure is too low
Delayed ignition burner
1. Manifold pressure is too low
2. Burner orifice clogged
1. Contact local natural gas company
2. Clean burner (see Cleaning and Mainte-
nance, page 15) or replace burner orifice
Burner backfiring during combustion
1. Burner orifice is clogged or damaged
1. Clean burner (see Cleaning and Mainte-
nance, page 15) or replace burner orifice
2. Replace damaged burner
2. Damaged burner
3. Gas regulator defective
3. Replace gas control
Slight smoke or odor during initial operation 1. Not enough air
1. Check burner for dirt and debris. If
found, clean burner (see Cleaning and
Maintenance, page 15)
2. Gas regulator defective
2. Replace gas control
3. Residues from manufacturing processes 3. Problem will stop after a few hours of
and logs curing
operation
Moisture/condensationnoticedonwindows 1. Not enough combustion/ventilation air
1. Refer to Air for Combustion and Venti-
lation requirements (page 4)
Heater produces a whistling noise when 1. Turning control knob to HI position 1. Turn control knob to LO position and
burner is lit
when burner is cold
2. Air in gas line
let warm up for a minute
2. Operate burner until air is removed from
line. Have gas line checked by local
natural gas company
3. Air passageways on heater blocked
3. Observe minimum installation clear-
ances (see page 7)
4. Dirty or partially clogged burner orifice 4. Clean burner (see Cleaning and Mainte-
nance, page 15) or replace burner orifice
Dark residue on logs or inside of fireplace
1. Improper log placement
1. Properly locate logs (see Installing Gas
Log Heater Into Stove, page 10 )
2. Drafts or other air currents affecting 2. Eliminate source of drafts around heater
flame pattern
3. Air holes at burner inlet blocked
4. Burner flame holes blocked
3. Clean out air holes at burner inlet. Peri-
odically repeat as needed
4. Remove blockage
Whitepowderresidueformingwithinburner 1. When heated, vapors from furniture pol- 1. Turn heater off when using furniture
box or on adjacent walls or furniture
ish, wax, carpet cleaners, etc. may turn
into white powder residue
polish, wax, carpet cleaners, or similar
products
Continued
104463
17
Download from Www.Somanuals.com. All Manuals Search And Download.
VENT-FREE NATURAL GAS STOVE HEATER
TROUBLESHOOTING
Continued
WARNING: If you smell gas
• Shut off gas supply.
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any phone in
your building.
• Immediately call your gas supplier from a neighbor’s phone.
Follow the gas supplier’s instructions.
• Ifyoucannotreachyourgassupplier,callthefiredepartment.
IMPORTANT: Operating heater where impurities in air exist may create odors.
Cleaningsupplies,paint,paintremover,cigarettesmoke,cementsandglues,new
carpet or textiles, etc., create fumes. These fumes may mix with combustion air
and create odors. These odors will disappear over time.
POSSIBLE CAUSE
OBSERVED PROBLEM
REMEDY
1. Metal expanding while heating or con-
tracting while cooling
Heater produces a clicking/ticking noise
just after burner is lit or shut off
1. This is common with most heaters. If
noise is excessive, contact qualified ser-
vice person
1. Heater burning vapors from paint, hair
spray, glues, cleaners, chemicals, new
carpet, etc. (See IMPORTANT state-
ment above)
Heater produces unwanted odors
1. Open window and ventilate room. Stop
using odor causing products while heater
is running
2. Gas leak. SeeWarning statement at
top of page
2. Locate and correct all leaks (see Check-
ing Gas Connections, page 12)
1. Not enough fresh air is available
2. Low line pressure
3. ODS/pilot is partially clogged
Heater shuts off in use (ODS operates)
1. Open window and/or door for ventilation
2. Contact local natural gas company
3. Clean ODS/pilot (see Cleaning and
Maintenance, page 15)
1. Gas leak. SeeWarning statement at
top of page
2. Control valve defective
Gas odor even when control knob is in OFF
position
1. Locate and correct all leaks (see Check-
ing Gas Connections, page 12)
2. Replace control valve
1. Foreign matter between control valve
and burner
Gas odor during combustion
1. Take apart gas tubing and remove for-
eign matter
2. Gas leak. SeeWarning statement at
top of page
2. Locate and correct all leaks (see Check-
ing Gas Connections, page 12)
104463
18
Download from Www.Somanuals.com. All Manuals Search And Download.
OWNER’S MANUAL
PARTS CENTRALS
These Parts Centrals are privately owned businesses. They have agreed to support our
customer’s needs by providing original replacement parts and accessories.
ACCESSORIES
Purchase these heater accessories from
your local dealer. If they can not supply
these accessories, call DESA International
at 1-866-672-6040 for referral informa-
tion. You can also write to the address
listed on the back page of this manual.
Baltimore Electric
1348 Dixwell Avenue
Hamden, CT 06514-0322
1-800-397-7553
East Coast Energy Products
707 Broadway
W. Long Branch, NJ 07764-1542
732-870-8809
203-248-7553
1-800-755-8809
Parts Department
Portable Heater Parts
342 N. County Rd. 400 East
Valparaiso, IN 46383-9704
All States
Dayton Hardware
P.O. Box 275
North Dayton Station
Dayton, OH 45404-0275
All States
219-462-7441
1-888-619-7060
937-258-3721
OH 1-800-762-3426
EQUIPMENT SHUTOFF
VALVE - GA5010
Halco Enterprises
208 Carter Drive, Unit 21
West Chester, PA 19382-4500
610-430-7717
1-800-368-0803
For all models. Equipment shutoff valve
with 1/8" NPT tap. Fits 1/2" NPT pipe.
FBD
1349 Adams Street
Bowling Green, KY 42103-3414
270-846-1199
CLEANING KIT - CCK
(Not Shown)
1-800-654-8534
For all models. Your vent-free gas appli-
ance requires regular cleaning and mainte-
nance to prevent performance problems.
This kit gives you the tools and instructions
to make it easy to clean all critical areas of
your appliance.
Fax: 1-800-846-0090
Laporte’s Parts & Service
2444 N. 5th Street
Hartsville, SC 29550-7704
843-332-0191
Master Parts Dist.
1251 Mound Ave NW
Grand Rapids, MI 49504-2672
616-791-0505
1-800-446-1446
Fax: 616-791-8270
Parts Department
Cans Unlimited, Inc.
P.O. Box 645
Taylor, SC 29687-0013
All States
803-879-3009
1-800-845-5301
INFORMATION VIDEO
108917-01
For all models. A care and maintenance
videoisavailablebycalling1-866-672-6040.
Washer Equipment Co.
1715 Main Street
Kansas City, MO 64108-2195
KS, MO, AR
816-842-3911
104463
19
Download from Www.Somanuals.com. All Manuals Search And Download.
VENT-FREE NATURAL GAS STOVE HEATER
ILLUSTRATED
PARTS
BREAKDOWN
SL30NT
1
17
2
15
9
7
8
10
6
12
5
15
4
18
18
11
13
3
14
16
18
104463
20
Download from Www.Somanuals.com. All Manuals Search And Download.
OWNER’S MANUAL
This list contains replaceable parts used in your stove. For replacement parts see Parts Central on page 19
of this manual.
PARTS LIST
SL30NT
KEY PART
NO.
NO.
DESCRIPTION
QTY.
1
104459-01
098249-01
104384-03
104454-01
098867-14
104425-01
104424-01
099056-26
102843-01
102980-01
101329-21
104472-01
099211-01
102445-01
099387-13
098271-10
104285-01
M11084-38
Stove Log
1
2
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
7
2
Nut, M5
3
Painted Base Assembly
Bracket, Regulator
Gas Regulator
Inlet Tube
4
5
6
7
Outlet Burner Tube
Burner Orifice Injector
Burner Clip
8
9
10
11
12
13
14
15
16
17
18
Burner
Control Valve
Bracket
Screw
Piezo Ignitor
Pilot Tube
Ignitor Cable
ODS Pilot (NG)
Screw, Hex Head (#8-18 x .38)
PARTS AVAILABLE — NOT SHOWN
100563-01
101054-01
100565-01
101137-04
Warning Plate
1
1
1
1
Lighting Instructions Plate
Warning Plate Fastener
Hardware Kit
104463
21
Download from Www.Somanuals.com. All Manuals Search And Download.
VENT-FREE NATURAL GAS STOVE HEATER
ILLUSTRATED
PARTS
BREAKDOWN
CISC
CISG
1L
1C
7
1R
6
5-4
5-4
4
4
5-1
2
3
5-2
5-3
104463
22
Download from Www.Somanuals.com. All Manuals Search And Download.
OWNER’S MANUAL
Thislistcontainsreplaceablepartsusedinyourstove. ForreplacementpartsseePartsCentralonpage
19 of this manual.
PARTS LIST
CISC
CISG
KEY PART
NO.
NO.
DESCRIPTION
QTY.
1L
1C
1R
2
104171-06
104171-05
104171-07
104969-01
104969-02
104174-03
104970-01
104970-02
104971-01
*
Top Grate with Screen - Left (Black Only)
Top Grate with Screen - Center (Black Only)
Top Grate with Screen - Right (Black Only)
Bottom Door (Charcoal)
Bottom Door (Forest Green)
Stove Dropped Bottom
One Leg (Charcoal) (4 Total Per Stove)
One Leg (Forest Green) (4 Total Per Stove)
Hardware Kit
Door Hinge Step Bolt With Shoulder (1 Per Unit)
Door Catch Bolt M8 x 1.25 - 55mm Long With Two M8
Hex Nuts (1 Per Unit)
Bottom Floor Bolts M6 x 1 - 25mm Long With Flat Washer
And Lock Washer (4 Per Unit)
Leg Attachment Stud, Headless, Slotted,
M10 x 1.5 - 40mm Long
1
1
1
1
1
1
1
1
1
1
3
4
5
5-1
5-2
*
1
1
4
5-3
5-4
6
*
*
104178-01
104968-01
Back Panel Bolts M6 x 1 - 20mm Long With Flat Washer
And Lock Washer (6 Per Unit)
Stove Back Panel (Black Only)
1
1
7
PARTS AVAILABLE — NOT SHOWN
104108-08
104108-05
Touch-up Spray Paint 12 oz Can (Charcoal)
Touch-up Spray Paint 12 oz Can (Forest Green)
1
1
* Included In Hardware Kit
104463
23
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY INFORMATION
KEEP THIS WARRANTY
Model
Serial No.
Date Purchased
Always specify model and serial numbers when communicating with the factory.
We reserve the right to amend these specifications at any time without notice. The only warranty applicable is our standard written
warranty. We make no other warranty, expressed or implied.
LIMITED WARRANTY
VENT-FREE PROPANE/LP GAS LOG HEATERS AND EMPIRE STOVE CHASSIS
DESA International warrants this product to be free from defects in materials and components for two (2) years from the date of first
purchase,providedthattheproducthasbeenproperlyinstalled,operatedandmaintainedinaccordancewithallapplicableinstructions.
To make a claim under this warranty the Bill of Sale or cancelled check must be presented.
This warranty is extended only to the original retail purchaser. This warranty covers only the cost of part(s) required to restore this
heater to proper operating condition. Warranty part(s) MUST be obtained through authorized dealers of this product and/or DESA
Internationalwhowillprovideoriginalfactoryreplacementparts. Failuretouseoriginalfactoryreplacementpartsvoidsthiswarranty.
The heater MUST be installed by a qualified installer in accordance with all local codes and instructions furnished with the unit.
This warranty does not apply to parts that are not in original condition because of normal wear and tear, or parts that fail or become
damaged as a result of misuse, accidents, lack of proper maintenance or defects caused by improper installation. Travel, diagnostic
cost, labor, transportation and any and all such other costs related to repairing a defective heater will be the responsibility of the owner.
TO THE FULL EXTENT ALLOWED BY THE LAW OF THE JURISDICTION THAT GOVERNS THE SALE OF THE
PRODUCT; THIS EXPRESS WARRANTY EXCLUDES ANY AND ALL OTHER EXPRESSED WARRANTIES AND LIMITS
THE DURATION OF ANY AND ALL IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE TO TWO (2) YEARS FROM THE DATE OF FIRST PURCHASE; AND DESA
INTERNATIONAL’S LIABILITY IS HEREBY LIMITED TO THE PURCHASE PRICE OF THE PRODUCT AND DESA
INTERNATIONAL SHALL NOT BE LIABLE FOR ANY OTHER DAMAGES WHATSOEVER INCLUDING INDIRECT,
INCIDENTAL OR CONSEQUENTIAL DAMAGES.
Some states do not allow a limitation on how long an implied warranty lasts or an exclusion or limitation of incidental or consequential
damages, so the above limitation on implied warranties, or exclusion or limitation on damages may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights that vary from state to state.
For information about this warranty write:
TM
2701 Industrial Drive
P.O. Box 90004
Bowling Green, KY 42102-9004
104463-01
Rev. D
02/02
104463 01
NOT A UPC
Download from Www.Somanuals.com. All Manuals Search And Download.
|