Owner’s Manual
Model 9210, 9220, 9230
Vehicular Slide Gate Operators
DoorKing, Inc.
120 Glasgow Avenue
Inglewood, California 90301
U.S.A.
Phone: 310-645-0023
Fax: 310-641-1586
P/N 9210-065 Rev H, 8/08
Copyright 2001 DoorKing, Inc. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
Use this manual with the following models only.
Models 9210-080, 9210-081, 9210-082, 9210-083, 9210-084, 9210-086, 9210-087, 9210-088,
9210-089, 9210-090, 9210-091, 9220-080, 9220-081, 9220-082, 9220-083, 9220-084, 9220-085,
9220-086, 9220-087, 9230-080, 9230-081 with circuit board 4404-010.
DoorKing, Inc. reserves the right to make changes in the products described in this manual
without notice and without obligation of DoorKing, Inc. to notify any persons of any such revisions
or changes. Additionally, DoorKing, Inc. makes no representations or warranties with respect to
this manual. This manual is copyrighted, all rights reserved. No portion of this manual may be
copied, reproduced, translated, or reduced to any electronic medium without prior written consent
from DoorKing, Inc.
9210-065-H-8-08
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
GATE: A moving barrier such as a swinging, sliding, raising, lowering, or the like, barrier, that is a stand-alone
passage barrier or is that portion of a wall or fence system that controls entrance and/or egress by persons or
vehicles and completes the perimeter of a defined area.
RESIDENTIAL VEHICULAR GATE OPERATOR – CLASS I: A vehicular gate operator (or system) intended for
use in a home of one-to four single family dwelling, or garage or parking area associated therewith.
COMMERCIAL / GENERAL ACCESS VEHICULAR GATE OPERATOR - CLASS II: A vehicular gate operator
(or system) intended for use in a commercial location or building such as a multi-family housing unit (five or more
single family units), hotels, garages, retail store, or other building servicing the general public.
INDUSTRIAL / LIMITED ACCESS VEHICULAR GATE OPERATOR - CLASS III: A vehicular gate operator (or
system) intended for use in an industrial location or building such as a factory or loading dock area or other
locations not intended to service the general public.
RESTRICTED ACCESS VEHICULAR GATE OPERATOR - CLASS IV: A vehicular gate operator (or system)
intended for use in a guarded industrial location or building such as an airport security area or other restricted
access locations not servicing the general public, in which unauthorized access is prevented via supervision by
security personnel.
VEHICULAR BARRIER (ARM) OPERATOR (OR SYSTEM): An operator (or system) that controls a cantilever
type device (or system), consisting of a mechanical arm or barrier that moves in a vertical arc, intended for
vehicular traffic flow at entrances or exits to areas such as parking garages, lots or toll areas.
VEHICULAR HORIZONTAL SLIDE-GATE OPERATOR (OR SYSTEM): A vehicular gate operator (or system)
that controls a gate which slides in a horizontal direction that is intended for use for vehicular entrance and exit to
a drive, parking lot, or the like.
VEHICULAR SWING-GATE OPERATOR (OR SYSTEM): A vehicular gate operator (or system) that controls a
gate which moves in an arc in a horizontal plane that is intended for use for vehicular entrance and exit to a
drive, parking lot, or the like.
SYSTEM: In the context of these requirements, a system refers to a group of interacting devices intended to
perform a common function.
WIRED CONTROL: A control implemented in a form of fixed physical interconnections between the control, the
associated devices, and an operator to perform predetermined functions in response to input signals.
WIRELESS CONTROL: A control implemented in means other than fixed physical interconnections (such as
radio waves or infrared beams) between the control, the associated devices, and an operator to perform
predetermined functions in response to input signals.
INHERENT ENTRAPMENT PROTECTION SYSTEM: A system, examples being a motor current or speed
sensing system, which provides protection against entrapment upon sensing an object and is incorporated as a
permanent and integral part of the operator.
EXTERNAL ENTRAPMENT PROTECTION DEVICE: A device, examples being an edge sensor, a photoelectric
sensor, or similar entrapment protection device, which provides protection against entrapment when activated
and is not incorporated as a permanent part of an operator.
ENTRAPMENT: The condition when an object is caught or held in a position that increases the risk of injury.
Page 4
9210-065-H-8-08
Download from Www.Somanuals.com. All Manuals Search And Download.
Entrapment Protection
Protection Against Entrapment
Gate Operator Category
Horizontal Slide, Vertical Lift, Swing and Vertical Barrier (arm)
Vertical Pivot
Usage Class
Vehicular I and II
Vehicular III
Primary
Secondary
Primary
A or C
Secondary
A
B1, B2 or D
A, B1, B2, C or D
A, B1 or B2
A, B1, B2, D or E
A, B1, B2 or C
A, B1, B2, C,
D or E
Vehicular IV
A, B1, B2 or D
A, B1, B2, D or E
A, B1, B2, C or D
A, B1, B2, C,
D or E
TYPE A:
Inherent entrapment protection system.
TYPE B1:
Provision for connection of, or supplied with, a non-contact sensor
(photoelectric sensor or the equivalent). When used as the PRIMARY
device, must be monitored.
TYPE B2:
Provision for connection of, or supplied with, a contact sensor (edge
device or the equivalent). When used as the PRIMARY device, must be
monitored.
TYPE C:
TYPE D:
Inherent adjustable clutch or pressure relief device.
Provision for connection of, or supplied with, an actuating device
requiring continuous pressure to maintain opening or closing motion of
the gate.
TYPE E:
An inherent audio alarm.
9210-065-H-8-08
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Notices
Vehicular gate operator products provide convenience and security. However, gate operators must
use high levels of force to move gates and most people underestimate the power of these systems
and do not realize the potential hazards associated with an incorrectly designed or installed system.
These hazards may include:
•
•
•
•
•
•
•
Pinch points
Entrapment areas
Reach through hazards
Absence of entrapment protection devices
Improperly located access controls
Absence of vehicle protection devices
Absence of controlled pedestrian access
In addition to these potential hazards, automated vehicular gate systems must be installed in
accordance with the UL-325 Safety Standard and the ASTM F2200 Construction Standard. Most lay
persons are unaware of, or are not familiar with, these standards. If an automated vehicular gate
system is not properly designed, installed, used and maintained, serious injuries or death can result.
Be sure that the installer has instructed you on the proper operation of the gate and gate operator
system. Be sure that the installer has trained you about the basic functions of the required reversing
systems associated with your gate operating system and how to test them. These include reversing
loops, inherent reversing system, electric edges, photoelectric cells, or other external devices.
•
•
This Owner’s Manual is your property. Keep it in a safe place for future reference.
Be sure that all access control devices are installed a minimum distance of 10 feet
away from the gate and gate operator, or in such a way that a person cannot touch the
gate or gate operator while using the device. If access control devices are installed in
violation of these restrictions, immediately remove the gate operator from service and contact
your installing dealer.
Loops and loop detectors, photo-cells or other equivalent devices must be installed to prevent the
gate from closing on vehicular traffic.
•
The speed limit for vehicular traffic through the gate area is 5 MPH. Install speed bumps and
signs to keep vehicular traffic from speeding through the gate area. Failure to adhere to
posted speed limits can result in damage to the gate, gate operator, and to the vehicle.
•
Be sure that all persons who will use the gate system are familiar with the proper use of the
gate and gate operator and are familiar with the possible hazards associated with the gate
system.
•
•
Be sure that warning signs are permanently installed on both sides of the gate in an area
where they are fully visible to traffic.
It is your responsibility to periodically check all entrapment protection devices. If any of these
devices are observed to function improperly, remove the operator from service immediately
and contact your installing or servicing dealer.
•
•
Follow the recommended maintenance schedule.
Do not allow children to play in the area of the operator or to play with any gate-operating
device.
•
To remove the gate operator from service, operate the gate to the full open position and then
shut off power to the operator at the service panel.
Page 6
9210-065-H-8-08
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Instructions
WARNING - To reduce the risk of injury or death:
1.
2.
READ AND FOLLOW ALL INSTRUCTIONS.
Never let children operate or play with gate controls. Keep the remote control away
from children.
3.
4.
Always keep people and objects away from gate. NO ONE SHOULD CROSS THE
PATH OF THE MOVING GATE.
Test the operator monthly. The gate MUST reverse on contact (contact sensors must
be installed) with a rigid object or stop or reverse when an object activates the non-
contact sensors. After adjusting the force or the limit of travel, retest the gate
operator. Failure to adjust and retest the gate operator properly can increase the risk
of injury or death.
5.
6.
Use the emergency release only when the gate is not moving.
KEEP GATES PROPERLY MAINTAINED. Read the owner's manual. Have a
qualified service person make repairs to gate hardware.
7.
8.
The entrance is for vehicles only. Pedestrians must use separate entrance.
SAVE THESE INSTRUCTIONS!
Gate Construction
Vehicular gates should be constructed and installed in accordance with ASTM F2200; Standard
Specification for Automated Vehicular Gate Construction. For a copy of this standard, contact ASTM
9210-065-H-8-08
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
Instructions regarding intended installation:
Install the gate operator only if:
1.
The operator is appropriate for the construction of the gate and the usage class of
the gate.
2.
All openings of a horizontal slide gate are guarded or screened from the bottom of
the gate to a minimum of 4 feet (1.22 m) above the ground to prevent a 2 ¼ inch
(57.2 mm) diameter sphere from passing through the openings anywhere in the gate,
and in that portion of the adjacent fence that the gate covers in the open position.
3.
4.
All exposed pinch points are eliminated or guarded.
Guarding is supplied for exposed rollers.
The operator is intended for installation only on gates used for vehicles. Pedestrians must be supplied
with a separate access opening. The pedestrian access opening shall be designed to promote
pedestrian usage. Locate the gate such that persons will not come in contact with the vehicular gate
during the entire path of travel of the vehicular gate.
The gate must be installed in a location so that enough clearance is supplied between the gate and
adjacent structures when opening and closing to reduce the risk of entrapment. Swinging gates
should not open into public access areas.
The gate must be properly installed and work freely in both directions prior to the installation of the
gate operator. Do not over-tighten the operator clutch, pressure relief valve or reduce reversing
sensitivity to compensate for a damaged gate.
For gate operators utilizing Type D protection:
1.
The gate operator controls must be placed so that the user has full view of the gate
area when the gate is moving.
2.
3.
A warning placard shall be placed adjacent to the controls.
An automatic closing device (such as a timer, loop sensor, or similar device) shall not
be employed.
4.
No other activation device shall be connected.
Controls intended for user activation must be located at least ten feet (10’) away from any moving
part of the gate and where the user is prevented from reaching over, under, around or through the
gate to operate the controls. Outdoor or easily accessible controls should have a security feature to
prevent unauthorized use.
The Stop and/or Reset button must be located in the line-of-sight of the gate. Activation of the reset
control shall not cause the operator to start.
A minimum of two (2) WARNING SIGNS shall be installed, one on each side of the gate where easily
visible.
For gate operators utilizing a non-contact sensor:
1.
2.
3.
See the instructions on the placement of non-contact sensors for each type of
application.
Care shall be exercised to reduce the risk of nuisance tripping, such as when a
vehicle trips the sensor while the gate is still moving in the opening direction.
One or more non-contact sensors shall be located where the risk of entrapment or
obstruction exist, such as the perimeter reachable by a moving gate or barrier.
Page 8
9210-065-H-8-08
Download from Www.Somanuals.com. All Manuals Search And Download.
For gate operators utilizing contact sensors:
1.
One or more contact sensors shall be located where the risk of entrapment or
obstruction exist, such as at the leading edge, trailing edge, and post mounted both
inside and outside of a vehicular horizontal slide gate.
2.
3.
4.
One or more contact sensors shall be located at the bottom edge of a vehicular
vertical lift gate.
One or more contact sensors shall be located at the pinch point of a vehicular vertical
pivot gate.
A hardwired contact sensor shall be located and its wiring arranged so that the
communication between the sensor and the gate operator is not subjected to
mechanical damage.
5.
7.
A wireless contact sensor such as one that transmits radio frequency (RF) signals to
the gate operator for entrapment protection functions shall be located where the
transmission of the signals are not obstructed or impeded by building structures,
natural landscaping or similar obstructions. A wireless contact sensor shall function
under the intended end-use conditions.
One or more contact sensors shall be located at the bottom edge of a vertical barrier
(arm).
9210-065-H-8-08
Page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
Slide Gate Requirements
All openings of a horizontal slide gate are guarded or screened from the
bottom of the gate to a minimum of four (4) feet (1.22 m) above the ground to
prevent a 2 1/4 inch (57.2 mm) diameter sphere from passing through the
openings anywhere in the gate and in that portion of the adjacent fence that
the gate covers in the open position.
The operator is intended for installation only on gates used for vehicles.
Pedestrians must be supplied with a seperate access opening. The
pedestrian access opening shall be designed to promote pedestrian
usage. Locate the gate such that persons will not come in contact with
the vehicular gate during the entire path of travel of the vehicular gate.
(ref. UL325 56.8.4.b)
(ref. UL325 56.8.4.a.2 and ASTM F2200 6.1.2)
Roadway
Fence
Pedestrian
Access
Fence
A
Vehicular Gate
Operator
Sidewalk
Fence
Gate
4 ft.
min
A gap, measured in the horizontal plane parallel to
the roadway, between a fixed stationary object
nearest the roadway (such as a gate support post)
and the gate frame when the gate is in either the
fully open position or the fully closed position, shall
not exceed 2 1/4 inch (57.2 mm).
A
(ref. ASTM F2200 6.1.4)
2 1/4"
Max
2 1/4"
Max
Operator
B
Pad
This area between the gate and fence has a high risk of entrapment. The gap between the fence and gate should not exceed
2 ¼ inches. Install a filler or barrier in this area to reduce this gap to 2 ¼ inches or less.
A
B
Install a contact sensor (type B2) on the fence to help minimize the risk of entrapment in this area.
Page 10
9210-065-H-8-08
Download from Www.Somanuals.com. All Manuals Search And Download.
Slide Gate Protection
Loops to help minimize the potential of the gate to
close when a vehicle is present. Number and
placement of loops is dependent on the application.
1
2
Contact sensor installed on the fence to help minimize
the potential of entrapment between the gate and
fence.
Reverse
Loop
1
6
5
Fence
Pedestrian
Access
2
3
4
Fence
5
Operator
Non-contact sensor to help minimize the potential
of the gate closing on vehicular or other traffic that
loops cannot sense.
3
4
5
6
Sidewalk
Reverse (Open)
Loop
1
Non-contact sensor to help minimize the potential
of entrapment during the back travel of the gate.
Warning signs are to be placed on each side of the
gate so that they are easily visible from either side
of the gate.
Open Loop
(Optional)
1
A separate pedestrian access located so
pedestrians cannot come in contact with the
vehicular gate.
9210-065-H-8-08
Page 11
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Section 1 – Installation
1.1
1.2
1.3
1.4
1.5
1.6
1.7
Specifications ...........................................................................................................................................15
Mounting Options .....................................................................................................................................16
Chain Guide Adjustment...........................................................................................................................17
Pad Mount Installation..............................................................................................................................18
Mounting Stand Installation ......................................................................................................................20
Chain Installation......................................................................................................................................22
Warning Sign Installation..........................................................................................................................24
Section 2 – Wiring
Conduits ...................................................................................................................................................25
2.1
2.2
2.3
2.4
2.5
2.6
High Voltage Connections........................................................................................................................26
Control Wiring...........................................................................................................................................27
Loop Detector Wiring................................................................................................................................28
Auxiliary Device Wiring.............................................................................................................................29
Primary / Secondary (Bi-Parting) Wiring...................................................................................................30
Terminal Identification and Description
2.6.1
2.6.2
2.6.3
Main Terminals.........................................................................................................................31
Limit Switch Connector.............................................................................................................32
Reversing Device Connector....................................................................................................32
Section 3 – Adjustments
3.1
3.2
Circuit Board Adjustments........................................................................................................................33
Switch Settings.........................................................................................................................................34
3.2.1
3.2.2
SW 1 (Right Switch) Description and Function ........................................................................35
SW 2 (Left Switch) Description and Function...........................................................................35
3.3
Limit Switch Adjustment
3.3.1
3.3.2
Limit Switch Adjustment for 9210 Operator..............................................................................36
Limit Switch Adjustment for 9220 and 9230 Operators............................................................37
3.4
3.5
3.6
Reverse Adjustment .................................................................................................................................38
Speed Control...........................................................................................................................................39
Current Sensor Wiring Information...........................................................................................................39
Page 12
9210-065-H-8-08
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4 – Operating Instructions
4.1
4.2
Power and Reset Switches ......................................................................................................................41
Shutdown Conditions
4.2.1
4.2.2
4.2.3
4.2.4
Soft Shutdown..........................................................................................................................42
Resetting a Soft Shutdown.......................................................................................................42
Hard Shutdown ........................................................................................................................43
Resetting a Hard Shutdown .....................................................................................................43
4.3
Manual Gate Operation............................................................................................................................44
Section 5 – Maintenance and Troubleshooting
5.1
5.2
5.3
5.4
Maintenance Schedule.............................................................................................................................45
Operator Diagnostics................................................................................................................................46
Troubleshooting........................................................................................................................................47
Accessories..............................................................................................................................................49
Wire Diagrams
115 VAC .................................................................................................................................................50
230 VAC, 1-Phase....................................................................................................................................51
208 VAC, 3-Phase....................................................................................................................................52
230 VAC, 3-Phase....................................................................................................................................53
208 VAC, 1-Phase Variable Speed..........................................................................................................54
208 VAC, 3-Phase Variable Speed..........................................................................................................55
230 VAC, 1-Phase Variable Speed..........................................................................................................56
230 VAC, 3-Phase Variable Speed..........................................................................................................57
9210-065-H-8-08
Page 13
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 14
9210-065-H-8-08
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 1 - INSTALLATION
Prior to beginning the installation of the slide gate operator, we suggest that you become familiar with
the instructions, illustrations, and wiring guide-lines in this manual. This will help insure that your
installation is performed in an efficient and professional manner. The proper installation of the
vehicular slide gate operator is an extremely important and integral part of the overall access control
system. Check all local building ordinances and building codes prior to installing this operator. Be
sure your installation is in compliance with local codes.
1.1
Specifications
Class of Operation:
Type of Gate:
Class III, IV
Vehicular Slide Gates Only
9210/9220: 1 HP; 9230: 3 HP
Horsepower:
Voltage / Phase:
9210/9220: 115, 208, 230 VAC 1Ø / 208, 230 VAC 3Ø
9230: 208, 230 VAC 3Ø
Current:
9210/9220: 1Ø: 15 A @ 115V, 7.5 A @ 208V, 7.4 A @ 230V
9210/9220: 3Ø: 3.4 A @ 208V, 3.3 A @ 230V
9230 3Ø: 12.4 A @ 208/230V
9210: 3000 Lbs; 9220: 2000 Lbs; 9230: 5000 Lbs.
100 Feet
Max Gate Wt.1
Max Gate Length:
Cycles / Hr:
60/Hr
Speed:
9210: Approx 1 Ft./Sec.
9220/9230: Adjustable ½ - 2 Ft./Sec.
Primary – Inherent (Type A)
Entrapment Protection:
Secondary – Provision for connection of a non-contact
sensor (Type B1) and/or a contact sensor (Type B2).
Secondary entrapment protection devices are not supplied
with the operator and must be ordered separately.
Note 1:
Assumes gate is in good working condition installed on a
level surface.
2
16
16
9210-065-H-8-08
Page 15
Download from Www.Somanuals.com. All Manuals Search And Download.
1.2
Mounting Options
The 9210, 9220 and 9230 vehicular gate operators are designed to be mounted on the optional
mounting stand (p/n 9200-135) or directly to a concrete pad. The mounting stand option is
recommended if the gate length exceeds 30 feet since this mounting method will allow a “chain rest”
to be mounted on the gate.
Pad mounting is typically
used with gates that are less
than 30 feet in length.
Requires use of the pad
mounting plate that is
included with the operator.
Pedestal
mounting
is
typically used with gates that
are greater than 30 feet in
length since this method
allows a chain rest to be
installed on the gate.
Requires use of the pad
mounting plate that is
included with the operator.
Requires
use
of
the
OPTIONAL
operator
mounting stand.
Page 16
9210-065-H-8-08
Download from Www.Somanuals.com. All Manuals Search And Download.
1.3
Chain Guide Adjustment
After determining which mounting method is to be used (pad or mounting stand), adjust the chain
guides according to the mounting method being used.
To gain access to the inside of the operator,
remove three hex-head nuts from the left side of
the control panel housing.
Pull the housing out and away.
OPEN
For pad mounted operators, remove the UPPER
hole knockouts from each side of the operator.
Adjust the chain guides as shown.
Chain will be routed OVER the chain guides and
UNDER the drive sprocket.
For operators mounted on the mounting stand,
DO NOT remove any hole knockouts.
Adjust the chain guides as shown.
Chain will be routed UNDER the chain guides
and OVER the drive sprocket.
9210-065-H-8-08
Page 17
Download from Www.Somanuals.com. All Manuals Search And Download.
1.4
Pad Mount Installation
1. Construct a form for the mounting pad according to the specifications shown below. Be
sure to level the top edge of the form and that the top of the form is a minimum of four (4)
inches above ground level. We suggest that you contact the local building department to
determine the required depth of the pad since soil conditions and code requirements vary
from city to city.
2. Set conduits, reinforcing bars and/or wire mesh if required. The number of conduits is
determined by the application requirements. We suggest using a minimum of four (4)
conduits. 1-High voltage power lines; 2-Low voltage control lines; 3-Loop lead-in wires
(open loop); 4-Loop lead-in wires (reverse loops). Conduits can be set in the areas
indicated in the illustration. See SECTION 2. Set additional conduits as required for your
application. NOTE: If conduits are not set in the pad, they can be routed to a J box
where connections to the operator can be made after it is installed. There are four (4) ½-
inch knockouts in the operator for this purpose.
28
GATE
GATE
GATE
4
GATE
7.5
11.25
12.0
16.0
16.75
20.5
Minimum 4 inches
above ground level.
Pad depth determined by soil
conditions and local building codes.
Minimum depth is 18 inches.
3. Mix the concrete according to the manufacturers instructions. Pour the mixture into the
form and tamp. Level and finish the surface after pouring is complete. Do not set anchor
Page 18
9210-065-H-8-08
Download from Www.Somanuals.com. All Manuals Search And Download.
bolts in the concrete. Sleeve anchors should be used to secure the operator to the
pad. This allows greater flexibility in positioning the operator on the pad.
4. Allow the pad to cure for 48 hours before removing the forms or mounting the operator.
5. Once the pad has cured, place the operator / mounting plate on the pad in the proper
position; 4-inches from the front and sides of the pad and 1-inch from the rear of the pad.
The operator mounting plate must be parallel to the gate. CAUTION: the operator
is heavy. Two persons are required to lift the operator onto the mounting pad.
6. Once the operator is in the proper position on the pad, secure the operator mounting
plate directly to the pad using 3/8 or 1/2 x 3 sleeve anchors. Be sure that the operator
mounting plate is parallel to the gate.
9210-065-H-8-08
Page 19
Download from Www.Somanuals.com. All Manuals Search And Download.
1.5
Mounting Stand Installation
1. Construct a form for the mounting pad according to the specifications shown below. Be
sure to level the top edge of the form and that the top of the form is a minimum of four (4)
inches above ground level. We suggest that you contact the local building department to
determine the required depth of the pad since soil conditions and code requirements vary
from city to city.
2. Set conduits, reinforcing bars and/or wire mesh if required. The number of conduits is
determined by the application requirements. We suggest using a minimum of four (4)
conduits. 1-High voltage power lines; 2-Low voltage control lines; 3-Loop lead-in wires
(open loop); 4-Loop lead-in wires (reverse loops). Conduits can be set in the areas
indicated in the illustration. See SECTION 2. Set additional conduits as required for your
application. NOTE: If conduits are not set in the pad, they can be routed to a J box
where connections to the operator can be made after it is installed. There are four (4) ½-
inch knockouts in the operator for this purpose.
GATE
GATE
GATE
GATE
4
39.25
Pad depth determined
by soil conditions and
local building codes.
Minimum depth is 18
inches.
Minimum 4
inches above
ground level.
Page 20
9210-065-H-8-08
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Mix the concrete according to the manufacturers instructions. Pour the mixture into the
form and tamp. Level and finish the surface after pouring is complete. Do not set anchor
bolts in the concrete. Sleeve anchors should be used to secure the operator to the
pad. This allows greater flexibility in positioning the operator on the pad.
4. Allow the pad to cure for 48 hours before removing the forms or mounting the operator.
5. Once the pad has cured, place the operator-mounting stand on the pad in the proper
position; 4-inches from the front and sides of the pad and 1-inch from the rear of the pad.
The operator-mounting stand must be parallel to the gate.
6. Once the stand is in the proper position on the pad, secure the operator-mounting stand
directly to the pad using 3/8 or 1/2 x 3 sleeve anchors. Be sure that the operator-
mounting stand is parallel to the gate.
7. After securing the mounting stands to the pad, place the operator onto the mounting
stand and secure it with the hardware provided. CAUTION: the operator is heavy.
Two persons are required to lift the operator onto the mounting plate.
Chain Rest
9210-065-H-8-08
Page 21
Download from Www.Somanuals.com. All Manuals Search And Download.
1.6 Chain Installation
1. Secure the chain brackets to each end of the gate so that the brackets will be level with
the chain where it exits the operator.
Brackets should be attached to the inside of
the frame so that the chain bolts, when
attached, do not protrude beyond the frame
of the gate.
2. Route the chain through the gate operator.
3. Attach the chain to the chain bolts using the
master links supplied, and then attach the
chain bolts to the chain brackets using the
hardware supplied. Make any adjustments to
the chain length at this time.
4. Adjust the chain bolts to tighten the chain.
The chain should sag no more than one (1)
inch per 10 feet of travel. Do not over tighten the chain. IMPORTANT!! Be sure that the
chain is parallel to the gate. Installing the chain in any other manner will cause
excessive noise, chain idler wear and chain stretching.
Page 22
9210-065-H-8-08
Download from Www.Somanuals.com. All Manuals Search And Download.
9210-065-H-8-08
Page 23
Download from Www.Somanuals.com. All Manuals Search And Download.
1.7 Warning Sign Installation
This DoorKing slide gate operator is shipped with two warning signs. The purpose of the warning
signs is to alert uniformed persons, and to remind persons familiar with the system, that a potential
hazard may exist so that appropriate action can be taken to avoid the hazard or to reduce exposure
to the hazard.
1. Permanently install the supplied warning signs in locations
WARNING
so that the signs are visible by persons on both sides of
the gate.
2. Use appropriate hardware such as wood or metal screws
(not supplied) to install the warnings.
Moving Gate Can Cause
Serious Injury or Death
KEEP CLEAR! Gate may move at any time
without prior warning.
Do not let children operate the gate or play
in the gate area.
This entrance is for vehicles only.
Pedestrians must use separate entrance.
Page 24
9210-065-H-8-08
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 2 – WIRING
Before attempting to connect any wiring to the operator, be sure that the circuit breaker in the
electrical panel is in the OFF position. Permanent wiring must be installed to the operator as required
by local electrical codes. It is recommended that such work be performed by a licensed electrical
contractor.
Since building codes vary from city to city, we highly recommend that you check with your
local building department prior to installing any permanent wiring to be sure that all wiring to
the operator (both high and low voltage) complies with local code requirements.
THIS GATE OPERATOR MUST BE PROPERLY GROUNDED!!
PRIMARY
OPERATOR
SECONDARY
OPERATOR
SLIDE GATE CONDUIT REQUIREMENTS
(Typical)
Low Voltage Control Devices
Loop Lead-In Wires
High Voltage Power
The conduit requirements shown are for a typical slide gate operator installation (the secondary
operator is shown for those applications where a secondary operator may be used). The conduit
requirements for your application may vary from this depending on your specific needs.
Use only sweeps for conduit bends. Do not use 90° connectors as this will make wire pulls very
difficult and can cause damage to wire insulation.
We suggest that minimum ¾-inch conduit be used.
Be sure that all conduits are installed in accordance with local codes.
9210-065-H-8-08
Page 25
Download from Www.Somanuals.com. All Manuals Search And Download.
2.1 High Voltage Connections
Use the table below to determine high voltage wire size requirements. The distance shown in the
chart is measured in feet from the operator to the power source. If power wiring is greater than the
maximum distance shown, it is recommended that a service feeder be installed. When large gauge
wire is used, a separate junction box must be installed for the operator connection. The wire table is
based on stranded copper wire. Wire run calculations are based on a maximum 3% voltage drop on
the power line, plus an additional 10% reduction in distance to allow for other losses in the system.
INPUT POWER
AMPS
WIRE SIZE / DISTANCE IN FEET
12 AWG
60
10 AWG
90
8 AWG
150
6 AWG
240
1 HP: 115 VAC – 1Ø
15
1 HP: 208/230 VAC – 1Ø
1 HP: 208/230 VAC – 3Ø
3 HP: 208/230 VAC 3Ø
7.5/7.4
3.4/3.3
12.4
200
330
520
840
530
840
1340
490
2100
790
190
310
Route incoming high voltage power through conduit and into the operator up the right side of the
control box.
Be sure wiring is installed in accordance with local codes. Be sure to color code all wiring.
It is recommended that a surge suppresser be installed on the high voltage power lines to help
protect the operator and circuit board from surges and power fluctuations.
DETAIL A
GROUND
DETAIL A
L1
L2
L3
L4
L5
HIGH VOLTAGE
INPUT
115 VAC
OUTPUT
POWER
TERMINALS
L1 - L2
L1 - L2
L1 - L2 - L3
L1 - L2 - L3
115 VAC SINGLE PHASE
230 VAC SINGLE PHASE
208 VAC THREE PHASE
230 VAC THREE PHASE
INCOMING
POWER WIRES
L1 = HOT (BLACK)
L2 = NEUTRAL (WHITE)
Page 26
9210-065-H-8-08
Download from Www.Somanuals.com. All Manuals Search And Download.
2.2
Control Wiring
Controls must be far enough from the gate so that the user is prevented from coming in
contact with the gate while operating the controls. Outdoor or easily accessible controls
should have a security feature to prevent unauthorized use.
Fence
C
Roadway
D
Gate
A
B
Close contact sensor
placed on gate.
Wireless option
available.
Open contact
sensor placed
on fence.
C
D
Open direction non-contact sensor.
Close direction non-contact sensor.
Open direction contact sensor.
Close direction contact sensor.
A
B
C
D
4404-010
Circuit Board
Common
Relay
Power
Receiver
1
Fire
Dept
2
3
Telephone
Entry
Open Photo
Close Photo
Open Edge
Close Edge
Common
OPEN
CLOSE
STOP
A
Common
Z
4
Call
Stand-Alone
Card Reader
Diagram above is for illustration purposes. The actual placement
of the secondary protection devices is dependent on the specific
installation requirements.
Secondary entrapment protection devices must be installed with
this gate operator. This protection may be provided by non-
contact or contact sensors, or a combination of both.
Stand-Alone
Keypad
Secondary device wiring shows inputs to the circuit board only.
Photo-cells must be supplied with power.
Refer to the safety instructions in the front of this manual for
more information.
Key
Switch
Controls must be installed a minimum of 10-feet from the gate or
installed in such a way that the person using the control cannot
come in contact with the gate or gateoperator.
All inputs to the 4404 circuit board are Normally Open (N.O.).
1
2
3
4
Radio receiver power only. Power here is limited to 250 ma.
Partial open input. Devices connected here will open the gate to the partial open limit setting only.
Reverse input functions only when gate is in the closing cycle.
Must use a DoorKing 3-button control station. Others will not work.
DOORKING, INC., INGLEWOOD, CA 90301
Title: Model 9210, 9220, 9230, 9530
Control and Secondary Device Wiring
Date: 11/07 Dwg. No. 4404-CNTRL-1 Rev.
A
9210-065-H-8-08
Page 27
Download from Www.Somanuals.com. All Manuals Search And Download.
2.3
Loop Detector Wiring
Loops and loop detectors must be installed with this gate operator to prevent the gate from
accidentally closing on vehicles that may be in the path of the gate.
8 Loops and loop detectors MUST be installed with this gate
operator to help prevent the gate from accidentally closing on
vehicular traffic.
8 Loop detector wiring is shown for DoorKing plug-in loop
detectors only. If other loop detectors are used, refer to the
installation instructions supplied with those detectors for
wiring instructions.
8 If other detectors are used, use a separate power supply to
power these detectors.
8 Loop layout shown is for a typical slide gate application with
two-way traffic, or one-way exit only traffic.
Exit
8 Reverse loops are wired in series. See detail A.
8 Refer to the Loop Information Manual (available from
detectors.
Reverse
From outside
Reverse loop
From inside
Reverse loop
TB 1
Reverse
Detail A
Detail A
DoorKing
Loop Detector
DoorKing
Loop Detector
REVERSE
EXIT
LOOP
LOOP
P2
POWER
LMT
LIMIT SWITCH
CONNECTOR
P8
REV SENS
OPEN
P6
REV SENS
CLOSE
4 3 2 1
8 7 6 5 4 3 2 1
TIME
DELAY
P7
REVERSING DEVICE
CONNECTOR
P5
20 19 18
17 16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
DOORKING, INC., INGLEWOOD, CA 90301
Title: Model 9210, 9220, 9230, 9530
Loop Detector Wiring
Date: 11/07 Dwg. No. 4404-LOOP-1
Rev.
A
Page 28
9210-065-H-8-08
Download from Www.Somanuals.com. All Manuals Search And Download.
2.4
Auxiliary Device Wiring
The auxiliary stop switch will stop a moving gate when activated or will prevent the gate operator from starting when activat ed. Note that
this input is normally open and that a switch closure is required to activate the stop function. Because of this, the auxiliary stop
shown must NEVER be used as a safety interlock device.
1
Jumper is placed across terminals 7 and 8 ONLY WHEN THE AUXILIARY STOP INPUT IS USED.
The Remote Alarm Reset Station MUST be mounted in the line-of-sight of the gate operator.
2
3
4
Using a 2351-010 Tracker Expansion Board, operator data can be sent to the access controller (DoorKing 1833, 1835, 1837 or 1838 only).
Refer to Installation Manual 2351-065 for detailed information.
Auxiliary Stop Using Magnetic Switch
1
Operator
Stopped
Normal
Operation
4404-010
Circuit Board
2
Open Photo
Close Photo
Open Edge
Close Edge
Common
Common
White
Red
Green
DoorKing 1404-080
Remote Reset Switch
3
1
2
1
2
3
3
4
4
5
5
6
6
7
7
8
8
9
9
10
11
12
13
14
15
16
10
11
12
13
14
2351-010
Circuit Board
17
18
DoorKing 2351-010
Tracker Expansion Board
4
DOORKING, INC., INGLEWOOD, CA 90301
Title: Model 9210, 9220, 9230, 9530
Auxiliary Device Wiring Diagram
Date: 11/07 Dwg. No. 4404-AUXDEV-1 Rev.
A
9210-065-H-8-08
Page 29
Download from Www.Somanuals.com. All Manuals Search And Download.
2.5
Primary – Secondary (Bi-Parting) Gate Wiring
The interface wiring between the two operators requires seven (4) wires (18 AWG minimum) for
control and secondary entrapment protection device connection. Each operator must be connected to
its own power source as described in section 2.1.
D
E
A
B
C
D
E
Connect the Primary / Secondary interconnection wiring as shown. Wire colors are based
on DoorKing interconnection cable(P/N 2600-75x).
1
2
3
4
Place a jumper from terminal 2 to terminal 4 in the PRIMARY operator only.
Set SW 1, Switch 3 to the OFF position in the PRIMARY operator.
Open direction non-contact sensor - Primary Operator.
Close direction non-contact sensor - Both Operators.
Open direction non-contact sensor - Secondary Operator.
Open direction contact sensor - Primary Operator.
Open direction contact sensor - Secondary Operator.
A
B
C
D
E
Plug a two-channel (P/N 9409-010) loop detector into the OPEN loop port in the
PRIMARY operator. Connect loops and loop detector as shown.
Connect radio receiver as shown. If partial open feature is desired with radio receiver,
connect receiver relay to terminal5. Connect other OPEN devices to terminal 4 (Full
Open) or terminal 5 (Partial Open) as required.
Connect standard reverse devices to terminal6 and/or connect secondary non-contact
and/or contact sensors to Secondary Entrapment Protection inputs as shown.
5
6
Connect chassis ground to chassis ground.
4404-010
Circuit Board
4404-010
Circuit Board
Common
Relay
Power
Yellow
Yellow
Brown
Brown
4
2
Orange
5
Orange
Open Photo
Close Photo
Open Edge
Close Edge
Common
Open Photo
Close Photo
Open Edge
Close Edge
Common
Gray
Gray
Reverse Loop
Common
Common
5
5
Reverse Loop
Exit Loop
Green
Green
6
6
TB1 TB2
TB3
Primary
Operator
Secondary
Operator
DoorKing
9409-010
3
Conduit
1
DOORKING, INC., INGLEWOOD, CA 90301
Title: Model 9210, 9220, 9230, 9530
Primary / Secondary Wiring Diagram
Date: 11/07 Dwg. No. 4404-DUAL-1
Rev.
A
Page 30
9210-065-H-8-08
Download from Www.Somanuals.com. All Manuals Search And Download.
2.6
Terminal Identification and Description
2.6.1 Main Terminal (P1)
1.
2.
LOW VOLTAGE COMMON
OPEN / CLOSE INPUT
When gate is closed, input will open gate to full position.
When gate is open and auto close timer is turned on, input will re-set and hold timer.
When gate is open and auto close timer is turned off, input will close gate.
When gate is closing, input will reverse gate.
3.
4.
24 VAC RADIO RECEIVER POWER, 250 MA MAXIMUM
FULL OPEN – CLOSE / EXIT LOOP LOGIC OUTPUT
If SW 1, switch 3 is OFF, this terminal becomes the logic output of the loop detector
plugged into the EXIT loop port (DoorKing loop detectors only).
If SW 1, switch 3 is ON, this terminal is identical to terminal 2.
5.
6.
PARTIAL OPEN INPUT
This input will open the gate to the mid-limit switch setting.
REVERSE / STOP INPUT
When gate is fully closed or in the opening cycle, this input has no affect on the gate
operator.
When gate is open and auto close timer is turned ON, input will re-set and hold timer.
When gate is open and auto close timer is turned OFF, input will prevent gate from
closing.
When gate is closing, input will REVERSE gate if SW 1, switch 7 is OFF.
When gate is closing, input will STOP gate if SW 1, switch 7 is ON.
7.
8.
3-BUTTON OPEN INPUT - Use with DoorKing 3 button control stations only (P/N
1200-006 and 1200-007).
3-BUTTON CLOSE INPUT - Use with DoorKing 3 button control stations only (P/N
1200-006 and 1200-007).
9.
GATE TRACKER - DATA
GATE TRACKER - BUSY
DRY RELAY CONTACT
10.
11.
Operation of relay is dependent on setting of SW 1, switches 4 and 5. Relay contacts
can be set for Normally Open (NO) or Normally Closed (NC) operation. Contact
rating is 1 amp maximum at 24 Volts.
12.
13.
14.
15.
16.
17.
18.
19.
20.
DRY RELAY CONTACT
LOW VOLTAGE COMMON
ALARM OUTPUT – Can also be connected to external alarm reset (P/N 1404-080)
ALARM RESET – Can also be connected to external alarm reset (P/N 1404-080)
CURRENT SENSOR
CURRENT SENSOR
120 VAC HOT INPUT TO CIRCUIT BOARD
120 VAC NEUTRAL INPUT TO CIRCUIT BOARD
EARTH GROUND / CHASSIS
9210-065-H-8-08
Page 31
Download from Www.Somanuals.com. All Manuals Search And Download.
2.6.2 Limit Switch Connector
The limit switch connector is located at the upper left-hand corner of the 4404 circuit board and
provides input to the circuit board from the limit switches.
1.
2.
3.
4.
5.
6.
7.
8.
FULL LIMIT
SLOW DOWN
PARTIAL LIMIT
SLOW DOWN
FULL LIMIT
LIMIT ENABLE
LIMIT COMMON
LIMIT COMMON
2.6.3 Reversing Device Connector
External entrapment prevention devices are connected here.
1. OPEN PHOTO-BEAM
This input is only active when the gate is in the opening cycle. An open photo-beam input
during the opening cycle will cause the gate to stop. The gate will remain stopped until
the photo-beam input is cleared, at which time the gate will resume the open cycle.
2. CLOSE PHOTO-BEAM
This input is only active when the gate is in the closing cycle. A close photo-beam input
during the closing cycle will cause the gate to stop. The gate will remain stopped until the
photo-beam input is cleared, at which time the gate will resume the close cycle.
3. OPEN EDGE
This input is only active when the gate is in the opening cycle. An open edge input during
the opening cycle will cause the gate to stop and then reverse.
If the gate reaches the full closed position, the gate will remain closed, ignore any
maintained inputs and enter a soft shutdown condition. NOTE: If the gate was initially
activated by a time clock with a contact closure across the gate operator open input, this
input will be ignored until another input (open loop, reverse loop. etc.) is received by the
gate operator.
If a close edge sensor is activated prior to the gate reaching the full closed position, the
gate will stop and enter a soft shutdown condition.
4. CLOSE EDGE
This input is only active when the gate is in the closing cycle. A close edge input during
the closing cycle will cause the gate to stop and then reverse.
If the gate reaches the full open position, the timer will automatically close the gate (if it is
turned on). Once the gate starts to close again, if the close edge input is activated a
second time prior to the gate reaching the full closed position, the operator will stop and
reverse and will enter a soft shutdown condition.
If an open edge sensor is activated prior to the gate reaching the full open position, the
gate will stop and enter a soft shutdown condition.
5. COMMON
Common terminal for the secondary entrapment protection device inputs.
6. COMMON
Page 32
9210-065-H-8-08
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 3 - ADJUSTMENTS
The switch settings and adjustments in this chapter should be made after your installation and wiring
to the operator(s) is complete. Whenever any of the programming switches on the circuit board are
changed, power must be shut-off, and then turned back on for the new setting to take effect.
3.1
Circuit Board Adjustments
Set the DIP-switches on the circuit board to the desired setting. See switch-setting charts in section
3.2.
Auto close timer (when turned on) can be set from 1 second (full counter clockwise) to approximately
23 seconds (full clockwise).
Dry contact relay (terminals 11-12) can be set for Normally Open (NO) or Normally Closed (NC)
operation by placing the relay shorting bar on the NO or NC pins respectively.
Power LED indicates that low voltage power is applied to the circuit board.
Input LEDs should be OFF and will only illuminate when the input is activated.
The limit LED will be ON when the respective limit switch is activated.
P4
REVERSE
LOOP
EXIT
LOOP
LIMIT SWITCH
CONNECTOR
REV SENS
OPEN
P6
REV SENS
CLOSE
4 3 2 1
8 7 6 5 4 3 2 1
TIME
DELAY
REVERSING DEVICE
CONNECTOR
P5
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
9210-065-H-8-08
Page 33
Download from Www.Somanuals.com. All Manuals Search And Download.
3.2
Switch Settings
The two DIP-switches located on the circuit board are used to program the operator to operate in
various modes and to turn on or off various operating features. Whenever a switch setting is
changed, power to the operator must be turned OFF and then turned back on for the new setting to
take affect. Check and review ALL switch settings prior to applying power to the operator.
CAUTION: Switches on the circuit board are numbered right to left, not left to right.
SW 1 (RIGHT SWITCH)
SWITCH
1
FUNCTION
Direction
SETTING
DESCRIPTION
OFF
Changes open / close direction of operator.
ON
2
3
Auto Close
Timer
OFF
ON
Auto-close timer is OFF. Manual input required to close gate.
Auto-close timer is ON. Adjustable from 1-23 seconds.
Open Loop
Output
OFF
ON
Switches logic-level output of EXIT loop port to terminal 4.
Normal Setting. Control board responds internally to loop
detector plugged into exit loop port.
4 & 5
Relay & LED
4-OFF 5-OFF
4-OFF 5-ON
4-ON 5-OFF
4-ON 5-ON
Relay activated and LED on when gate is FULL OPEN.
Relay activated and LED on when gate is NOT CLOSED.
Relay activated and LED on when gate is OPENING and OPEN.
Relay activated and LED on when gate is OPENING or CLOSING.
6
7
Warn Before
Operate
OFF
ON
Normal setting.
Alarm will sound 2-3 seconds prior to the gate starting.
Reverse
OFF
Normal Setting. Input to terminal 7 will REVERSE gate during
close cycle.
Stop
ON
Input to terminal 7 will STOP gate during close cycle.
8
Quick Close
OFF
ON
Normal gate operation.
Opening gate will stop and begin to close as soon as all reversing
inputs (loops, beams) are clear regardless of the open position of
the gate.
SW 2 (LEFT SWITCH)
SWITCH
1
FUNCTION
SETTING
DESCRIPTION
Self Test
OFF
Normal setting.
(see note 1)
ON
Run self-test – bench test only.
2
3
4
Open Uphill
Open Downhill
Spare
OFF
ON
Normal setting.
Turn ON if gate opens in an uphill direction.
OFF
ON
Normal setting.
Turn ON if gate opens in a downhill direction.
OFF
Normal Setting.
ON
NOTES:
1. Do not run the self-test while the gate operator is connected to the gate. This self-test
feature is designed for bench-testing only.
Page 34
9210-065-H-8-08
Download from Www.Somanuals.com. All Manuals Search And Download.
3.2.1 SW 1 (Right Switch) Description and Function
Switch 1: Set so that the operator cycles open upon initial power up and open command. If the
operator cycles close, turn power off and change the setting on this switch.
Switch 2: Turns the auto close timer on or off. Set from 1 to 23 seconds. Loops and loop
detectors, photoelectric cells, or other like devices must be installed when the auto close
timer is used to prevent the gate from closing on vehicular traffic.
Switch 3: Determines if the output of the loop detector (DoorKing loop detectors only) plugged into
the EXIT port will be sent directly to the microprocessor to open the gate, or if the output is directed to
terminal 4 where it can then be connected to other input terminals
Switches 4-5: These work in conjunction with each other and determine when the relay on the board
will be activated. This relay can be used as a switch for various functions such as illuminating a
warning light when the gate is moving, or turning on a green light when the gate is full open. If a
magnetic lock is used with the gate operator, these switches must be set for magnetic lock operation
which limits the relay to activate only when the gate is opening and full open.
Switch 6: Warn Before Operate, When set to the ON position, the internal alarm in the operator will
sound 2-3 seconds prior to the gate starting.
Switch 7: Determines if an input to terminal 7 will reverse or stop a closing gate. If this switch is set
to stop the gate (ON), once the input to terminal 7 is cleared, the gate will continue to close. This is
typically used to help prevent tailgating.
Switch 8: Turning the quick-close feature on will cause the auto close timer to close the gate after 1
second, regardless of the setting of the auto close timer potentiometer. This will also cause an
opening gate to stop and reverse when the reverse (loop) inputs are cleared. This feature, along with
switch 7 above, is useful to prevent tailgating.
3.2.2 SW 2 (Left Switch) Description and Function
Switch 1: This switch must be in the OFF position for normal operation. The self-test feature checks
various functions of the operator. CAUTION - Do not run self-test with the operator connected to the
gate. The drive chain must be disconnected from the operator to run the self-test.
Switch 2: Set to the OFF position for normal operation. Set to the ON position if gate OPENS in an
UPHILL direction.
Switch 3: Set to the OFF position for normal operation. Set to the ON position if gate OPENS in a
DOWNHILL direction.
Switch 4: Spare – leave switch in the OFF position.
9210-065-H-8-08
Page 35
Download from Www.Somanuals.com. All Manuals Search And Download.
3.3
Limit Adjustment
3.3.1 Limit Adjustment for 9210 Operator
1.
2.
3.
Turn power off.
Push the lock plate handle down to adjust the Open and Close limit nuts.
After adjusting the limit-nuts, be sure that the lock-plate is engaged in the slots on the
limit-nuts to prevent them from slipping.
4.
5.
6.
Turn power on and activate the gate operator.
Re-adjust the limit-nuts as necessary for full-open and full-close gate travel.
If using the partial open feature (input to terminal 5), adjust the middle limit nut being
sure to align the magnet in the limit nut with the magnetic pick-up.
Partial Open Limit
Be sure the magnet
imbedded in the partial
open (center) limit nut is
aligned with the partial
open magnetic pick-up
Page 36
9210-065-H-8-08
Download from Www.Somanuals.com. All Manuals Search And Download.
3.3.2 Limit Adjustment for 9220, 9230 Operators
The 9220 and 9230 operators utilize a pair of switches at the open and close positions. The first
switch is the slow-down switch and the second switch is the limit switch. The slow-down switch is
adjustable so that you can increase or decrease when the slow-down is initiated. For example, on
heavy gates it is desirable to increase the slow-down distance to provide the operator more time to
slow-down and stop the gate.
1.
2.
3.
Turn power off.
Adjust the limit nuts as described in 3.3.1.
Loosen the nut that fastens the slow-down switch bracket to the partial open limit
switch bracket. This will allow the slow-down switch assembly to move up or down
approximately 3/4 inch. DO NOT remove the slow-down switch assembly
completely from the bracket it is attached to and then re-attach it in the larger
slot on the bracket in an attempt to gain further adjustment. This will only
cause mechanical damage to the switch assembly when the operator is
activated.
4.
To increase the slow-down distance, move the slow-down switch away from the limit
switch. To decrease the slow-down distance, move the slow-down switch closer to
the limit switch.
Decrease
Slow-down
Limit Switch
Limit Nut
Increase
Slow-down
Slow-Down Switch
Adjustable
9210-065-H-8-08
Page 37
Download from Www.Somanuals.com. All Manuals Search And Download.
3.4
Reverse Adjustment
This vehicular gate operator is equipped with an inherent (Type A) entrapment sensing system. This
system will sense an obstruction in either the opening or closing gate cycles and will cause the gate
to reverse direction should an obstruction be encountered. For this system to function correctly,
the gate must be properly installed and work freely in both directions. A good set of ball
bearing wheels (or rollers) is essential for proper slide gate operation.
1. Refer to section 3.6 before starting this adjustment.
2. Activate the gate operator by momentarily shorting terminal 1 and 5 with a 1-foot piece of
18 AWG wire. Be sure that the limit adjustment has been completed as described in
section 3.3.
3. While the gate is running open, slowly rotate the open reverse sensitivity potentiometer
clockwise until the gate reverses travel, then rotate the potentiometer 1/8 turn counter
clockwise. Note: Rotating the sensitivity adjustment clockwise INCREASES the reverse
sensitivity. Rotating this adjustment counter-clockwise DECREASES the reverse
sensitivity. NOTE: After the gate has reversed, the operator will assume a "soft
shutdown" making it necessary to initiate the cycle again by momentarily shorting across
terminals 1 and 5 as in step 1.
4. While the gate is running closed, slowly rotate the close reverse sensitivity potentiometer
clockwise until the gate reverses travel, then rotate the potentiometer 1/8 turn counter
clockwise. Note: Rotating the sensitivity adjustment clockwise INCREASES the reverse
sensitivity. Rotating this adjustment counter-clockwise DECREASES the reverse
sensitivity. NOTE: After the gate has reversed, the operator will assume a "soft
shutdown" making it necessary to initiate the cycle again by momentarily shorting across
terminals 1 and 5 as in step 1
5. Operate the gate a few times to be sure that it cycles completely.
6. Place an immobile object along the path of the gate so that the gate will strike it while in
the open cycle. The gate must reverse direction after striking the object. If it does not,
increase the reverse sensitivity by turning the potentiometer 1/8 turn clockwise, then
repeat this test. NOTE: After the gate has reversed, the operator will assume a "soft
shutdown" making it necessary to initiate the cycle again by momentarily shorting across
terminals 1 and 5 as in step 1.
7. Place an immobile object along the path of the gate so that the gate will strike it while in
the close cycle. The gate must reverse direction after striking the object. If it does not,
increase the reverse sensitivity by turning the potentiometer 1/8 turn clockwise, then
repeat this test. NOTE: After the gate has reversed, the operator will assume a "soft
shutdown" making it necessary to initiate the cycle again by momentarily shorting across
terminals 1 and 5 as in step 1 to reactivate the automatic close timer.
8. You may have to repeat step 2 several times to find the correct sensitivity adjustment.
INCREASE
INCREASE
REV SENS
CLOSE
REV SENS
OPEN
Page 38
9210-065-H-8-08
Download from Www.Somanuals.com. All Manuals Search And Download.
3.5
Speed Control (9220, 9230 Only)
The models 9220 and 9230 are equipped with
a speed control module that allows you to
adjust the speed of the gate from 1/2 to 2 Ft./
Sec. To adjust the speed, simply rotate the
speed control knob clockwise to increase the
gate speed, or counter clockwise to decrease
the gate speed. The digital readout on the
speed controller will display the gate speed.
L1
L2
L3
B- B+
1.0
1
ft/s
.5
ft/s
1.5
ft/s
0 ft/s
2 ft/s
U
V
W
PE PE
3.6
Current Sensor Wiring
This vehicular gate operator uses a current
sensing device to detect any obstructions in the
path of the opening or closing gate. The current
sensor uses a sensing coil with a given number of
turns through it to monitor the current flow into the
operator. Each time the wire passes through the
coil, it is considered a turn (see diagram below).
The number of turns through the sensing coil is
dependant on the operating voltage of the
operator, the speed of the gate and the weight of
the gate.
Voltage and Phase
115 Single Phase
230 Single Phase
208 Three Phase
230 Three Phase
460 Three Phase
Turns
1
2
5
6
7
In general, light weight gates may require additional turns of wire through the ERD sensor, while
heavier gates may require less turns. In addition, the speed of the gate can affect how the ERD
sensor works. Gates running at a higher speed may require less turns of wire through the sensor.
CAUTION – HIGH VOLATGE: Be sure power is turned OFF before making any wire
adjustments to the ERD sensor.
If you are setting the ERD sensitivity (section 3.4) and reach the full sensitive position without
activating the reversing function, add an additional turn of wire through the current sensor. If you are
decreasing the sensitivity and the gate will not run properly, reduce the number of turns through the
current sensor.
1 Turn
2 Turns
3 Turns
9210-065-H-8-08
Page 39
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 40
9210-065-H-8-08
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 4 – OPERATING INSTRUCTIONS
WARNING - To reduce the risk of injury or death:
1.
2.
READ AND FOLLOW ALL INSTRUCTIONS.
Never let children operate or play with gate controls. Keep the remote control away
from children.
3.
4.
Always keep people and objects away from gate. NO ONE SHOULD CROSS THE
PATH OF THE MOVING GATE
Test the operator monthly. The gate MUST reverse on contact with a rigid object or
stop or reverse when an object activates the non-contact sensors. After adjusting the
force or the limit of travel, retest the gate operator. Failure to adjust and retest the
gate operator properly can increase the risk of injury or death.
5.
6.
Use the emergency release only when the gate is not moving and power has been
shut-off.
KEEP GATES PROPERLY MAINTAINED. Read the owner's manual. Have a
qualified service person make repairs to gate hardware.
7.
8.
The entrance is for vehicles only. Pedestrians must use separate entrance.
SAVE THESE INSTRUCTIONS.
4.1
Power and Reset Switches
Open the power switch cover located on the side of the operator to access the MAIN POWER switch
and the operator RESET switch.
The RESET switch is used to turn off the
entrapment alarm and to reset the operator after
a hard shutdown has occurred.
The AC POWER toggle switch turns power to
the operator ON (toggle up) or OFF (toggle
AC
down).
POWER
OFF
9210-065-H-8-08
Page 41
Download from Www.Somanuals.com. All Manuals Search And Download.
4.2
Shutdown Conditions
Under various entrapment conditions the operator will assume either a soft or hard shutdown (alarm)
condition. To determine what type of reset action is required, you will need to understand how the
different entrapment conditions affect the gate operator.
4.2.1 Soft Shutdown
This occurs in various situations where the inherent or secondary entrapment protection devices have
been activated. In a soft shutdown condition, the operator will not respond to any input that was
present when the entrapment protection device sensed an obstruction. If the gate stops at the open
position, the operator will not respond to the automatic close timer.
Example 1: A time clock keys the gate open in the morning and an entrapment protection device
senses an obstruction prior to the gate reaching the full open position. If the entrapment is sensed by
the inherent system, the gate will reverse and run back to the closed position. The time clock input is
still present, but the gate will not re-open.
NOTE: In some systems, the time clock input comes from the telephone entry system relay. This
same relay may also provide open commands for a card reader, MicroPLUS transmitters and the
visitor telephone entry. If so, these devices will also be disabled in a soft shutdown condition.
Example 2: If the gate is closing and an entrapment protection device is activated, the gate will either
stop or reverse and run back to the open position, depending upon if the secondary or inherent
device was activated. The automatic close timer will not close the gate.
Example 3: Vehicle arrives at open loop and the gate runs towards the open position. The inherent
entrapment protection is activated. The gate reverses and runs back to the closed position. If the
vehicle is still present at the open loop a soft shutdown condition does not occur. The loop input
provides an immediate reset of the operator and the gate will again run to the open position.
4.2.2 Resetting a Soft Shutdown
In some conditions, a soft shutdown will reset as soon as the entrapment condition clears. For
example, if a non-contact sensor (photo cell) is sensing an obstruction, the operator will stop the gate
and assume a soft shutdown condition. When the photocell clears, the operator will return to normal
operation.
When the operator is in a soft shutdown, activation of any "intended input" will reset the operator. An
"intended input" includes any command, any standard safety input and any loop input. Activating any
of these inputs will reset the gate. At that point the gate will return to normal operation. If the gate is
open, the automatic close timer will then time out and close the gate.
Page 42
9210-065-H-8-08
Download from Www.Somanuals.com. All Manuals Search And Download.
4.2.3 Hard Shutdown
A hard shutdown condition occurs when the inherent entrapment protection system has sensed two
consecutive obstructions before the gate reaches the full open or full closed position. It can also be
an indication that the gate is too heavy or that the gate hardware (wheels, rollers) is in poor
condition and needs to be corrected. Do not reduce the operator reversing sensitivity in an
attempt to correct for a poorly designed gate or for hardware that is in need of repair.
Example: The gate is closing and the inherent entrapment protection system senses an obstruction
and causes the gate to reverse direction. As the gate begins to run in the open direction, a second
obstruction is sensed prior to the gate reaching the full open position. Once the second obstruction
has been sensed, the operator will stop, the audio alarm will be activated and all standard inputs are
shut down (including open commands, safety commands, loop inputs, etc.).
NOTE: The audio alarm will remain activated for a maximum of five minutes, or until the operator
receives a reset input. The hard shutdown condition will remain in affect even if the audio alarm
shuts off after five minutes.
After 5 minutes, the audio alarm will “chirp” every 5 seconds. This indicates that the operator is in a
hard shutdown condition and the reset switch must be activated to reset the operator and silence the
alarm.
4.2.4 Resetting a Hard Shutdown
When the operator is in a hard shutdown condition (audio alarm activated or audio alarm “chirps”
every 5 seconds), the only way to reset the gate operator and return it to normal operation is to
activate the alarm reset input. An alarm-reset switch can be mounted external of the gate operator
provided that it is installed in the line of sight of the gate and gate operator (see 2.6.1).
Before resetting a hard shutdown, determine why the shutdown occurred. Inspect the gate for any
obstructions along its path that could have activated the inherent entrapment sensing system.
Inspect the gate and gate hardware.
NOTE: DoorKing operators have a built-in alarm reset push button mounted on the operator above
the power ON-OFF toggle switch. Activating this button will return the gate operator to normal
operation, but will not activate the gate operator.
Once the gate has been reset, an open or close command is needed to start the gate operator. Most
activating commands will cause the gate operator to cycle to the open position. This includes
activation of a key switch or open command and activation of an open loop. Activation of a close
command will run the gate to the closed position.
NOTE: The gate operator will not lose its limit settings when a hard shutdown occurs.
9210-065-H-8-08
Page 43
Download from Www.Somanuals.com. All Manuals Search And Download.
4.3 Manual Gate Operation
This operator is equipped with a manual system that will allow the gate to be cranked open in the
event of a power outage or equipment failure.
NOTE: Never attempt to manually open any gate with an operator attached to it until you have
verified that power to the operator has been shut-off.
1. Unlock the manual release access panel
located on the top of the gate operator and
open it.
Opening this access panel
automatically activates an interlock switch
that will prevent the gate operator motor
from starting.
2. Insert the supplied manual hand crank into
the access hole until it engages with the
motor shaft. Turn the crank to open the
gate.
3. After the gate is opened, remove the crank
and lock the access panel closed.
Page 44
9210-065-H-8-08
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 5 – MAINTENANCE AND TROUBLESHOOTING
Inspection and service of this gate operator by a qualified technician should be performed anytime a
malfunction is observed or suspected. High cycle usage may require more frequent service checks.
5.1
Maintenance
When servicing the gate operator, always check any secondary (external) reversing devices (loops,
photo eyes, etc.) for proper operation. If external reversing devices cannot be made operable, do not
place this operator in service until the malfunction can be identified and corrected.
Always check the inherent reversing system when performing any maintenance. If the
inherent reversing system cannot be made operable, remove this operator from service until
the cause of the malfunction is identified and corrected. Keeping this operator in service
when the inherent reversing system is malfunctioning creates a hazard for persons which can
result in serious injury or death should they become entrapped in the gate.
When servicing this gate operator, always turn power OFF!!
MONTHLY
INTERVAL
MAINTENANCE SCHEDULE
3
6
12
Alarm
Activate the primary (inherent) reverse system by blocking the gate
with a solid object. When the gate reverses, block the gate in the
opposite direction prior to the limit being reached. The entrapment
alarm should activate. Press the reset button to silence the alarm.
ꢀ
Chain
Fire Dept.
Gate
Check for sagging. Tighten if necessary.
ꢀ
Check emergency vehicle access device for proper operation.
ꢀ
Inspect for damage. Check gate wheels, rollers and guides for
wear and grease if necessary.
ꢀ
ꢀ
Grease
Loop(s)
Wheels and guide rollers if necessary.
Check vehicular reverse and shadow loops for proper operation.
ꢀ
ꢀ
Primary Reverse
System
Check that the gate reverses on contact with an object in both the
opening and closing cycles. Adjust reversing sensitivity if
necessary.
Release
Check manual release for proper operation.
ꢀ
ꢀ
Secondary
Reverse Device
Check that secondary (external) reverse device(s) stop or reverse
the gate when activated.
Sprockets
Complete
Check setscrews for tightness.
ꢀ
Complete check of gate and gate operating system.
ꢀ
9210-065-H-8-08
Page 45
Download from Www.Somanuals.com. All Manuals Search And Download.
5.2 Operator Diagnostics
This gate operator is designed with built-in diagnostics that will alert you to potential or existing
problems that the microprocessor has detected. Specific fault conditions are checked and the
operator will signal that a fault exist through the built-in alarm.
Constant tone is heard when power is applied:
This indicates that the limit switch wire harness is not connected to the circuit board. In this condition,
the operator will not run and the tone will continue until the fault is corrected. Check to be sure that
the limit switch plug is properly inserted into P2.
Constant tone is heard:
This indicates that the operator is in a hard shutdown condition (section 4.2.3). The tone will continue
to sound for five minutes, and then will beep once every five seconds. The operator-reset button
must be pressed or power must be removed and then reapplied to return the operator to normal
operation.
Short tone is heard every five seconds:
This indicates that the operator has been in a hard shutdown condition in excess of five minutes.
This will continue until the operator-reset button is pressed or until power is removed from the
operator.
Operator runs for 1 second and stops, two short tones are heard:
This indicates that there may be a fault with the current sensor circuit.
Page 46
9210-065-H-8-08
Download from Www.Somanuals.com. All Manuals Search And Download.
5.3
Trouble Shooting
Have a good VOM meter to check voltages and continuity. A Meg-Ohm meter capable of checking
up to 500 meg-ohms of resistance is necessary to properly check the integrity of the ground loops.
When a malfunction occurs, isolate the problem to one of three areas: 1) the operator, 2) the loop
system, 3) the keying devices. Use caution when checking high voltage terminals, motor
capacitor and the motor.
1. Check the input indicator LEDs. They should only come ON when a keying device (card
reader, push button, etc.) is activated. If any of the input LEDs are ON continuously, this
will cause the gate operator to hold open. Disconnect the keying devices one at a time
until the LED goes OFF.
2. Check any external secondary entrapment protection devices. Any short or malfunction
in these devices can cause the gate operator to stop or to hold open.
3. A malfunction in a loop or loop detector can cause the gate operator to hold open, or to
not detect a vehicle when it is present over the loop. Pull the loop detector circuit boards
from the loop ports on the operator circuit board. If the malfunction persists, the problem
is not with the loop system. For more information on trouble shooting loops and loop
detectors, refer to your loop detector instruction sheet and to the DoorKing Loop and
Loop Detector Information Manual.
4. Check to be sure that there are no shorted or open control wires from the keying devices
to the gate operator. If a keying device fails to open the gate, momentarily jumper across
terminals 1 and 5 on the gate operator circuit board. If the gate operator starts, this
indicates that a problem exist with the keying device and is not with the gate operator.
5. If a three-button control station (open-close-stop) is connected to this gate operator,
check for proper wiring. Only a DoorKing three button control station (P/N 1200-006) can
be used with this gate operator. Others will cause a malfunction.
6. Check the high voltage supply. A voltage drop on the supply line (usually caused by
using too small supply voltage wires) will cause the operator to malfunction. Refer to the
wire size chart in section 2.1.
TROUBLESHOOTING
SYMPTON
POSSIBLE SOLUTION(S)
Check that power to the operator is turned ON.
•
•
Operator will not
run. Power LED is
OFF.
Transformer may be overheated. Turn power off and allow board to cool for several
minutes then retest. Check for low 120 VAC power and low voltage shorts.
•
•
•
Check for 120 VAC at terminals 18 and 19. If voltage measures 0, check power. If voltage
measures OK, check the terminal strip or replace the circuit board.
If a photocell is used as a secondary entrapment prevention device, check to be sure that
the beam is not blocked.
Operator will not
run. Power LED is
ON.
Momentarily jumper terminal 1 to terminal 5. If the input LED does not come ON, check
the terminal strip or replace the circuit board. If LED does come ON, proceed to next
steps.
•
•
•
Be sure that the chain is not too tight. A too tight chain may cause the operator to stall.
Turn power switch OFF and remove the control board.
Place a jumper wire from terminal 18 terminal 17. CAUTION – HIGH VOLTAGE. Turn the
power switch on. The motor should run. Turn the power switch off and remove the
jumper.
•
•
Place a jumper wire from terminal 18 to terminal 16. CAUTION – HIGH VOLTAGE. Turn
the power switch on. The motor should run in the opposite direction. Turn the power
switch off and remove the jumper.
If the motor runs in both steps above, replace the control board. If the motor does not run,
or runs in only one direction, problem can be a bad motor, motor capacitor, wire
connections from the control board to the motor or a bad control board.
9210-065-H-8-08
Page 47
Download from Www.Somanuals.com. All Manuals Search And Download.
•
Disconnect the gate from the gate operator and check that the gate slides freely without
any binding.
Gate opens a short
distance, then
stops and reverses.
•
•
•
Re-adjust the open reverse sensitivity.
Replace the circuit board.
Check the input LEDs. Any ON will hold the gate open and indicates a problem with a
keying device.
Gate opens but will
not close.
•
•
•
Check the secondary safety devices. Any activated will hold the gate open and indicates a
problem with the safety device.
Check the loop detectors. Any activated can hold the gate open and indicates a problem
with the loop detector or ground loop.
Operator may be in a “soft shutdown.” Activate any keying device to determine if operator
returns to normal operation.
•
•
•
If automatic close is desired, be sure SW-1, switch 2 is ON.
Check motor as described on previous page.
Operator may be in a “soft shutdown.” Check input LED on terminal 5. If it is ON,
momentarily disconnect, then re-connect the wire going to the terminal. Operator should
open.
Gate closes but will
not open.
•
•
Check to be sure that the operator is running in the proper direction. Turn power OFF, and
then back ON. Activate a keying device. Operator should run in the open direction. If
operator runs in the close direction, turn power OFF and change direction switch SW-1,
switch 1. Go to above section if operator now opens but will not close.
Be sure that the respective LED on the control board lights when the keying device
connected to the respective terminal is activated. If LED does not light, momentarily place
a jumper wire from terminal 1 to the input terminal being checked. If LED lights and gate
opens, problem is with the keying device. If LED does not light, replace control board.
•
•
•
Check motor as described on previous page.
Re-adjust the close reverse sensitivity.
Gate starts to
close, then
reverses to open.
Disconnect the gate from the operator and check that the gate operates freely without any
binding.
•
Check the loop detector LEDs and input LEDs. Any that flash ON will cause the gate to
reverse.
•
•
•
Replace the circuit board.
Check for any input or loop detector LEDs that are ON.
Gate closes and
then re-opens.
Check that the operator is running in the proper direction (see “gate closes but will not
open” above).
•
Operator is in a “hard shutdown” condition. Reset switch must be activated to return
operator to normal operation.
Entrapment alarm
is sounding.
Operator will not
run.
•
•
•
Check gate and gate hardware for any binding – correct where necessary.
Gate may be too heavy.
Operator has been in a “hard shutdown” condition in excess of 5 minutes. Reset switch
must be activated to return operator to normal operation.
Entrapment alarm
sounds a short
beep every 5
seconds.
•
•
The limit switch wire harness is not plugged into the circuit board. Check that the limit
switch connector is properly plugged into P2 on the circuit board.
Entrapment alarm
activates when
power is applied
and operator will
not run.
There may be a problem with the current sensor on the circuit board. Replace the circuit
board.
Operator runs for 1
second and stops,
two short beeps
are heard.
Page 48
9210-065-H-8-08
Download from Www.Somanuals.com. All Manuals Search And Download.
5.4
Accessories
The following accessory items can be used with the model 9210 / 9230 slide gate operator.
Contact Sensor
Photo Cell
Contact sensors for use as a secondary entrapment protection device.
Miller Edge, Inc. ME120, ME123, MG020, MGR20, MGS20
Non-contact (photo cells) sensors for use as a secondary entrapment
protection device – Listed to UL 325.
Infrared Thru-Beam with hood and built-in heater. 165-foot range.
P/N 8080-010
Photo-Reflective. 30-foot range.
P/N 8080-011
Infrared Thru-Beam. 65-foot range.
P/N 8080-031
Poloraized Photo-Reflective. 35-foot range.
P/N 8080-030
Loop Detector
Detectors plug directly into ports on circuit board simplifying wiring.
P/N 9410-010 - Single channel detector.
P/N 9409-010 - Two channel detector
Loop Wire
18 AWG loop wire with XLPE insulation is ideal for ground loops.
Available in 500 and 1000 foot rolls with red, blue or black insulation.
Pre-Fab Loops
Loop Test Meter
Control Station
Prefabricated ground loops. 24-foot circumference with 50-foot lead-in.
Available in yellow, red or blue jackets. Not for use in asphalt roadways.
Meg-ohm meter checks the integrity of ground loops.
P/N 9401-045
Three button interior and exterior control stations provide manual open-
close-stop gate operation.
P/N 1200-006 – Exterior / Interior
P/N 1200-007 - Interior
Time Clock
7 day and 365 day time clocks can be used to automatically open gate at
pre-set time and days. Compact clock fits inside the operator.
P/N 2600-791 – 7-day clock.
P/N 2600-795 – 365-day clock.
Surge Devices
High and low voltage surge suppressers help prevent circuit board failure
caused by lightning strikes and power surges.
P/N 1876-010 - High Voltage.
P/N 1878-010 - Low Voltage.
Gate Scale
Use to test ft/pounds required to move gate. P/N 2600-225
Speed Bumps
Prefabricated six-foot speed bump reduces traffic speed through gate
system. P/N 1610-150
Mounting Stand
Remote Reset
Heavy-duty pedestal mounting stand for the 9210 operator.
P/N 9200-135
Remote reset control station includes both audio and visual alarms to
indicate gate operator is in a hard-shutdown condition. Also provides a
reset button to reset the operator.
P/N 1404-080
Traffic Signal
Red / Green traffic signal is synchronized with the movement of the gate
and alerts drivers when it is safe to proceed.
P/N 1603-208
9210-065-H-8-08
Page 49
Download from Www.Somanuals.com. All Manuals Search And Download.
115 VAC
Motor 2600-278
50uf
50uf
Blue
115 VAC Convenience
Black
Black
Power
Switch
Black
White
Green
115 VAC
INPUT
Black
Black
P6
Black
COM
N.O.
INTERLOCK
White
P1
20 19 18 17 16 15 14 13 12 11 10
9
8
7
6
5
4
3
2
1
P2
Blue
1
COM
N.O.
N.O.
ALARM
LIMIT
2
RESET
ALARM
Red
3
4
5
6
7
8
CURRENT
SENSOR
COM
Black
MID-STOP
DOORKING, INC., INGLEWOOD, CA 90301
White
Title: Wiring Diagram Model 9210
115 VAC
COM
N.O.
LIMIT
Date: 10/05 Dwg. No. 9210-115-1
Rev.
A
Page 50
9210-065-H-8-08
Download from Www.Somanuals.com. All Manuals Search And Download.
230 VAC, 1-Phase
Motor 2600-280
Blue
115 VAC Convenience
30uf
1
2
3
4
5
6
10
Red
Blue
Power
Switch
Black
Black
Green
230 VAC
INPUT
Black
Black
P6
COM
N.O.
INTERLOCK
White
P1
20 19 18 17 16 15 14 13 12 11 10
9
8
7
6
5
4
3
2
1
P2
Blue
1
COM
N.O.
N.O.
ALARM
LIMIT
2
RESET
ALARM
Red
3
4
5
6
7
8
CURRENT
SENSOR
COM
Black
MID-STOP
DOORKING, INC., INGLEWOOD, CA 90301
White
Title: Wiring Diagram Model 9210
230 VAC, 1-Phase
COM
N.O.
LIMIT
Date: 10/05 Dwg. No.
9210-230-1
Rev.
A
9210-065-H-8-08
Page 51
Download from Www.Somanuals.com. All Manuals Search And Download.
208 VAC, 3-Phase
Motor 2600-295
L1
L2
L3
115 VAC Convenience
1
7
4
2
8
3
9
6
5
P4
P5
P6
1
2
3
4
5
6
10
Red
Blue
Black
A1
A2
B1
B2
C1
C2
D1
D0
D2
Power
Switch
Black
Black
Black
Green
208 VAC
3-Phase
Input
P6
Black
COM
N.O.
INTERLOCK
White
P1
20 19 18 17 16 15 14 13 12 11 10
9
8
7
6
5
4
3
2
1
P2
Blue
1
COM
N.O.
N.O.
ALARM
LIMIT
2
RESET
ALARM
Red
3
4
5
6
7
8
CURRENT
SENSOR
COM
Black
MID-STOP
DOORKING, INC., INGLEWOOD, CA 90301
White
Title: Wire Diagram Model 9210
208 VAC, 3-Phase
COM
N.O.
LIMIT
Date: 10/05 Dwg. No.
9210-208-3
Rev.
A
Page 52
9210-065-H-8-08
Download from Www.Somanuals.com. All Manuals Search And Download.
230 VAC, 3-Phase
Motor 2600-295
L1
L2
L3
115 VAC Convenience
1
7
4
2
8
3
9
6
5
P4
P5
P6
1
2
3
4
5
6
10
Red
Blue
Black
A1
A2
B1
B2
C1
C2
D1
D0
D2
Power
Switch
Black
Black
Black
Green
230 VAC
3-Phase
Input
P6
Black
COM
N.O.
INTERLOCK
White
P1
20 19 18 17 16 15 14 13 12 11 10
9
8
7
6
5
4
3
2
1
P2
Blue
1
COM
N.O.
N.O.
ALARM
LIMIT
2
RESET
ALARM
Red
3
4
5
6
7
8
CURRENT
SENSOR
COM
Black
MID-STOP
DOORKING, INC., INGLEWOOD, CA 90301
White
Title: Wire Diagram Model 9210
230 VAC, 3-Phase
COM
N.O.
LIMIT
Date: 10/05 Dwg. No.
9210-230-3
Rev.
A
9210-065-H-8-08
Page 53
Download from Www.Somanuals.com. All Manuals Search And Download.
208 VAC, 1-Phase Variable Speed
Motor 2600-295
Black
Red
Blue
L1
1
L2
2
L3
3
115 VAC Convenience
Orange
Shield
7
8
9
4
5
6
Blue
Red
P4
P5
P6
1
2
3
4
5
6
10
Shield
Wire
Nut
Orange
Blue
Red
L1 L2/N
B- B+
1
ft/s
Black
Black
Green
208 VAC
1-Phase
Input
.5
ft/s
1.5
ft/s
U
V
W
PE PE
0 ft/s
2 ft/s
Blue
Red
Black
P6
Black
COM
N.O.
INTERLOCK
White
20 19 18 17 16 15 14 13 12 11 10
9
8
7
6
5
4
3
2
1
COM
N.O.
N.O.
LIMIT
COM
P2
Blue
1
SLOW DOWN
ALARM
RESET
Yellow
2
3
4
5
6
7
8
Red
COM
N.O.
Green
Black
CURRENT
SENSOR
MID STOP
ALARM
COM
N.O.
SLOW DOWN
DOORKING, INC., INGLEWOOD, CA 90301
White
Title: Wire Diagram Model 9210 / 9220
208 VAC, 1-Phase, Variable Speed
COM
N.O.
LIMIT
Date:
2/07
Dwg. No. 9210-208-1-VS Rev.
B
Page 54
9210-065-H-8-08
Download from Www.Somanuals.com. All Manuals Search And Download.
208 VAC, 3-Phase Variable Speed
Motor
2600-295 (1 hp) or 2600-404 (3 hp)
Black
Red
Blue
L1
1
L2
2
L3
3
115 VAC Convenience
Orange
Shield
7
8
9
4
5
6
Blue
Red
P4
P5
P6
1
2
3
4
5
Red
Blue
6
10
Shield
Black
Orange
Blue
Red
Black
L1
L2
L3
B- B+
1
ft/s
Black
Black
Black
Green
208 VAC
3-Phase
Input
.5
ft/s
1.5
ft/s
U
V
W
PE PE
0 ft/s
2 ft/s
Blue
Red
Black
P6
Black
COM
N.O.
INTERLOCK
White
20 19 18 17 16 15 14 13 12 11 10
9
8
7
6
5
4
3
2
1
COM
N.O.
N.O.
LIMIT
COM
P2
Blue
1
SLOW DOWN
ALARM
RESET
Yellow
2
3
4
5
6
7
8
Red
COM
N.O.
Green
Black
CURRENT
SENSOR
MID STOP
ALARM
COM
N.O.
SLOW DOWN
DOORKING, INC., INGLEWOOD, CA 90301
White
Title: Wire Diagram Model 9210 / 9220 / 9230
208 Volt, 3-Phase, Variable Speed
COM
N.O.
LIMIT
Date:
2/07
Dwg. No. 9210-208-3-VS Rev.
D
9210-065-H-8-08
Page 55
Download from Www.Somanuals.com. All Manuals Search And Download.
230 VAC, 1-Phase Variable Speed
Motor 2600-295
Black
Red
Blue
L1
1
L2
2
L3
3
115 VAC Convenience
Orange
Shield
7
8
9
4
5
6
Blue
Red
P4
P5
P6
1
2
3
4
5
6
10
Shield
Wire
Nut
Orange
Blue
Red
L1 L2/N
B- B+
1
ft/s
Black
Black
Green
230 VAC
1-Phase
Input
.5
ft/s
1.5
ft/s
U
V
W
PE PE
0 ft/s
2 ft/s
Blue
Red
Black
P6
Black
COM
N.O.
INTERLOCK
White
20 19 18 17 16 15 14 13 12 11 10
9
8
7
6
5
4
3
2
1
COM
N.O.
N.O.
LIMIT
COM
P2
Blue
1
SLOW DOWN
ALARM
RESET
Yellow
2
3
4
5
6
7
8
Red
COM
N.O.
Green
Black
CURRENT
SENSOR
MID STOP
ALARM
COM
N.O.
SLOW DOWN
DOORKING, INC., INGLEWOOD, CA 90301
White
Title:
Wire Diagram Model 9210 / 9220
230 VAC, 1-Phase, Variable Speed
COM
N.O.
LIMIT
Date:
2/07
Dwg. No. 9210-230-1-VS Rev.
B
Page 56
9210-065-H-8-08
Download from Www.Somanuals.com. All Manuals Search And Download.
230 VAC, 3-Phase Variable Speed
Motor
2600-295 (1 hp) or 2600-404 (3 hp)
Black
Red
Blue
L1
1
L2
2
L3
3
115 VAC Convenience
Orange
Shield
7
8
9
4
5
6
Blue
Red
P4
P5
P6
1
2
3
4
5
Red
Blue
6
10
Shield
Black
Orange
Blue
Red
Black
L1
L2
L3
B- B+
1
ft/s
Black
Black
Black
Green
230 VAC
3-Phase
Input
.5
ft/s
1.5
ft/s
U
V
W
PE PE
0 ft/s
2 ft/s
Blue
Red
Black
P6
Black
COM
N.O.
INTERLOCK
White
20 19 18 17 16 15 14 13 12 11 10
9
8
7
6
5
4
3
2
1
COM
N.O.
N.O.
LIMIT
COM
P2
Blue
1
SLOW DOWN
ALARM
RESET
Yellow
2
3
4
5
6
7
8
Red
COM
N.O.
Green
Black
CURRENT
SENSOR
MID STOP
ALARM
COM
N.O.
SLOW DOWN
DOORKING, INC., INGLEWOOD, CA 90301
White
Title: Wire Diagram Model 9210 / 9220 / 9230
230 Volt, 3-Phase, Variable Speed
COM
N.O.
LIMIT
Date:
2/07
Dwg. No. 9210-230-3-VS Rev.
D
9210-065-H-8-08
Page 57
Download from Www.Somanuals.com. All Manuals Search And Download.
|