Quick Install Guide
Package Contents
LEDs (from top to bottom)
PowerLED - Asolidlightindicatesaproperconnection
to the power supply.
DIR-600L Wireless N 150 Home
Cloud Router
Internet LED - A solid light indicates connection on the
Internet port. This LED blinks during data transmission.
Power Adapter
WAN LEDs - A solid light indicates that the wireless
segment is ready. This LED blinks during wireless data
transmission.
Wireless N 150 Home
Cloud Router
Ethernet Cable
LAN LEDs (1-4) A solid light indicates a connection
to an Ethernet-enabled device on ports 1-4. This LED
blinks during data transmission.
If any of the above items are missing, please contact your reseller.
to download the user manual.
WPS LED/Button - Located on the side of the router.
Press to initiate the WPS process. The LED will blink
during the WPS configuration process.
DIR-600L
Start Here
To configure your router, go to the Manual Setup Section below and follow
the steps.
Tips for PPPoE and USB connections:
If you have DSL and are connecting via PPPoE, make sure that you disable or uninstall any PPPoE
software such as WinPoet, Broadjump, or Enternet 300 from your computer or you will not be able to
connect to the Internet.
You can only use the Ethernet port on your modem. If you were using USB to connect before, then you
must turn off your modem, disconnect the USB cable and connect an Ethernet cable to the Internet
port on the router, then turn the modem back on. In some cases, you may need to call your ISP to
change connection types (USB to Ethernet).
Important for Manual Setup: For the quick setup wizard to work properly, you
must have a working Internet connection. Ensure that you are able to use your
computer to get on the Internet before disconnecting your computer from your
modem.
mydlink Setup
Manual Setup
2
3
4
1
Modem
Router
Modem
Computer
Router
Computer
Modem
RESET
4
3
LAN
2
1
INTERNET
5
V
1
A
Router
RESET
4
3
LAN
2
1
INTERNET
5
V
1
A
RESET
4
3
LAN
2
1
INTERNET
5
V
1
A
Turn off and unplug your cable or DSL Position your router close to your modem and a computer. If you are currently using a router, disconnect all the
Plug one end of the included blue Ethernet cable that came with your
router into the yellow port labeled INTERNET on the back of the router.
broadband modem.
Place the router in an open area of your intended work area cables connected to it before installing the DIR-605L.
for better wireless coverage.
Unplug the Ethernet cable from your modem that is Plug the other end of this cable into the Ethernet port on your modem.
connected to your computer. Plug it into the LAN port
labeled 1 on the back of your router. The router is now
connected to your computer.
5
6
7
8
Router
Modem
Computer
RESET
Modem
4
3
LAN
2
1
INTERNET
5
V
A
Router
Computer
Modem
Reconnect the power adapter to your
cable or DSL broadband modem and wait
for two minutes.
Plug the power back into the modem and power it on.
Then connect the supplied power adapter into the power
receptor on the back of the router and then plug into a
power outlet or surge protector. Verify the power light is lit.
This is a sample network configuration of the setup after you have
completed all the setup steps.
From the computer you connected the router to, open a web
Press Enter and you will be directed to the D-Link Setup
Wizard page, which will detect your Internet connection type.
Follow the on-screen instructions to configure your Internet
settings. After setting up your router, you will be given the
option to create a mydlink account. Go to www. mydlink.com
and enter your acount information.
Note: Please refer to the user manual for more detailed installation
information and advanced features.
©2012 D-Link Corporation/D-Link Systems, Inc. All rights reserved. D-Link and the D-Link logo are registered trademarks of
D-Link Corporation or its subsidiaries in the United States and/or other countries. Other trademarks or registered trademarks
are the property of their respective owners. Maximum wireless signal rate derived from IEEE Standard 802.11g and 802.11n
specifications. Actual data throughput will vary. Network conditions and environmental factors, including volume of network
traffic, building materials and construction, and network overhead, lower actual data throughput rate. Environmental
conditions will adversely affect wireless signal range. Product specifications, size and shape are subject to change without
notice, and actual product appearance may differ from that depicted on the package.Visit dlink.com (US) or dlink.ca (Canada)
for more details. iPhone, iPad, and iPod touch are registered trademarks of Apple Inc.
Technical Support
If you experience issues registering this Router with your mydlink account, try
performing a hard reset by using an unfolded paperclip to press and hold the reset
button for 10 seconds while the Router is powered on. This may be necessary if
you have purchased an open box or resold unit.
United States
Canada
Version 1.0 (May 3, 2012)
U.S. and Canadian customers can contact D-Link technical support through our web site or by
phone. You can find software updates and user documentation on the D-Link website as well
as frequently asked questions and answers to technical issues.
Before you contact technical support, please have the following ready:
• Model number of the product (e.g. DIR-600L)
• Hardware Revision (located on the label on the bottom of the product (e.g. rev A1))
• Serial Number (s/n number located on the label on the bottom of the product).
Download from Www.Somanuals.com. All Manuals Search And Download.
|