Operator’s Manual
High Pressure Washer
Model 2200H
IMPORTANT:
READ SAFETY RULES AND INSTRUCTIONS CAREFULLY
CUB CADET P.O. BOX 368023 CLEVELAND, OHIO 44136-9722 [www.cubcadet.com]
FORM NO. 770-10449
(9/00)
Download from Www.Somanuals.com. All Manuals Search And Download.
MODEL 2200H OVERVIEW
Specifications
6.0 HP Briggs & Stratton Quantum
Engine
Water volume
Operating pressure
2.0 GPM
2200 PSI
7
9
10
Item Description
1. Water inlet
8
5
2. Detergent tray w/screw
3. Knob Assembly (two)
4. Oil fill cap
5. High pressure hose
6. Detergent suction tube
w/filter
12
11
7. Handle
6
8. Accessory rack
9. Trigger gun safety lock
10. Trigger gun
13
4
11. Pull start
12. Gas tank
13. Throttle
14
15
3
2
14. Choke
15. Wand w/adjustable
spray nozzle
16. High pressure outlet
(not pictured)
16
1
SAFE OPERATION PRACTICES — NEVER!
Never point nozzle at people or animals.
Never drink alcohol or use drugs while operating this equipment.
Never spray electrical connections, electrical outlets or fixtures.
Never add fuel with the engine running or operate where fuel has been spilled.
Never touch hot surfaces or allow accessories to contact hot surfaces.
Never operate in an enclosed space, exhaust fumes are dangerous.
Never operate near utilities with open flames.
Never operate without the water turned on and never use hot water.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFE OPERATION PRACTICES – Read First!
Water Supply
(Cold Water Only)
Safety Warnings
When using this product basic precautions
should always be followed:
•
•
•
Water hose must be at least 3/4 inch in
diameter.
•
Read all the instructions before using the
product.
Flow rate of water supply must not fall
below 2.5 GPM (gallons per minute).
•
FIRE HAZARD! Do not add fuel with the
engine running. Do not operate if fuel
has been spilled. Instead move the
machine to a different location and avoid
creating sparks.
Flow rate can be determined by running
the water for one minute into an empty
5-gallon container.
•
•
The water supply temperature must not
exceed 104°F/40°C.
•
•
Operate and fuel machine in a well
ventilated area, free of devices featuring
an open pilot or flame such as boilers,
water heaters, etc.
Never use the pressure washer to draw
in water contaminated with solvents, e.g.
paint thinners, gasoline, oil, etc.
High pressure jets can be dangerous if
subject to misuse. The jet must not be
directed at persons, animals, electrical
devices or the machine itself.
•
Always prevent debris from being drawn
into the unit by using a clean water
source.
•
•
Wear safety goggles.
We strongly recommend that this high
pressure washer not be left running for
periods of 5 minutes or longer without
the trigger gun being engaged.
Do not use acids, solvents, or any other
flammable material in this product.
These products can cause physical
injuries to the operator and irreversible
damage to the machine. If you have
further questions regarding the use of
This high pressure washer is equipped
with thermal protection to extend the
life of your pressure washer. The
thermal protector will automatically
recommended
cleaning
detergent,
please call your Cub Cadet dealer.
•
The machine has hot surfaces which can
cause burns. Operate the unit in a safe
environment and away from children.
activate
at
a
predetermined
temperature ejecting hot water before
resetting. This ensures that the pump
does not become damaged.
•
•
•
Do not allow the high pressure hose to
come into contact with the muffler guard.
Do not leave the machine running
unattended.
Learn how to stop the machine and
release pressure quickly. Be thoroughly
familiar with the controls.
Caution
•
•
Follow the maintenance instructions
specified in the manual.
•
•
Stay alert — watch what you are doing.
This machine has been designed
for use with cleaning detergent
supplied or recommended by the
manufacturer. The use of other
cleaning detergents may affect the
operation of the machine and void
the warranty.
Do not operate the product when
fatigued or under the influence of alcohol
or drugs.
•
•
Do not stand on unstable surfaces.
Stand with both feet balanced at all
times.
The Gun Safety Lock PREVENTS the
trigger from accidentally being engaged.
This safety feature DOES NOT lock the
trigger in the on position.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY INSTRUCTIONS
Step1 Slide the handle through the
accessory rack.
Step3 Insert the handle into the frame.
Align holes, insert bolt, and tighten with
knob.
Step2 Align the holes of the accessory
rack to the handle and fasten the four
screws.
Step4 Insert the spray wand into the
gun. Push in and turn clockwise to lock
spray wand in place. Turn the wand collar
clockwise onto the spray wand threads
until tight.
Step5 Attach high pressure hose to
trigger gun.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING INSTRUCTIONS
Step1 Fill gas tank with unleaded
Step2 Check oil level. Oil level should
always be between the “FULL” and “ADD”
marks on the dipstick. Be sure the machine
is level when checking the oil level. (Refer
to the engine’s operating manual for
seasonal grades).
gasoline. Do not use leaded gasoline.
Important! Do not run the engine with a
high or low oil level as this can cause
engine damage. If you have further
questions regarding the engine, please
refer to the engine’s operating manual
included with the unit.
Step4 Connect high pressure hose to
Step3 Connect garden hose to unit’s
high pressure outlet.
water inlet.
Step6 Trigger the gun to eliminate
trapped air, wait for a steady flow of water
to emerge from the spray nozzle.
Step5 Connect garden hose to the cold
water source and turn water on completely.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING INSTRUCTIONS - continued
Step8 Pull
the
starter
Step7 Slide the throttle control to the fast position.
Move the ckoke lever to the “CHOKE” position (only
if the engine is cool). After starting, move the choke
to “RUN”.
handle. If the engine fails to
start after 3 pulls squeeze
the trigger gun to release
pressure, and repeat step 8.
USING THE ACCESSORIES
Spray Wand
The spray wand allows you to adjust the cleaning pressure. To clean at maximum
pressure, the wand must be positioned to the high pressure setting (+). To apply
detergent, the wand must be positioned to the low pressure setting (-).
For high pressure turn
wand collar in the plus
(+) direction.
For low pressure turn
wand collar in the
minus (-) direction.
WARNING: TO AVOID SERIOUS INJURY, NEVER POINT SPRAY
NOZZLE AT YOURSELF, OTHER PERSONS OR ANIMALS
7
Download from Www.Somanuals.com. All Manuals Search And Download.
WORKING WITH DETERGENT
Detergents can only be applied in the “low” setting.
Step2 The wand must be set in the low
Step1 Slide the detergent tray into one
of the slots of your choice. Secure the tray
to the frame by fastening the screw.
pressure (-) position to apply detergents.
Step4 With the engine running, pull
trigger to operate unit: Liquid detergent is
drawn into the unit and mixed with water.
Apply detergent to work area. Do not allow
detergent to dry on surface.
Step3 Fill a container with Cub Cadet
detergent. Place the filter end of detergent
suction tube into the container. Be sure to
adjust the filter by turning it to the desired
detergent intake.
Cub Cadet biodegradable detergents are
specially formulated to protect the
environment and your pressure washer.
Special formula won’t clog the suction tube
filter and will protect the internal parts of
the pressure washer for a longer life. For
Cub Cadet Detergents, check your local
Cub Cadet dealer. If you need help locating
a dealer in your area, contact the Customer
Dealer Referral Line by calling:
For best results see Cleaning Tips on
pages 9 & 10 for specific information
on how to clean different surfaces.
Caution
Never use:
•
•
Bleach, Chlorine products and other
corrosive chemicals
Liquids containing solvents (i.e., paint
thinners, gasoline, oils)
1-877-835-7841
•
•
•
Tri-sodium phosphate products
Ammonia products
Acid-based products
One gallon container of the following Cub
Cadet detergents are available:
• Vehicle Wash Part No. KR-9103501
These chemicals will harm the unit and
will damage the surface being cleaned.
• Deck Wash
• Degreaser
• All Purpose
Cleaner
Part No. KR-9103502
Part No. KR-9103503
Part No. KR-9103504
Always Use Cub Cadet Detergents for
Best Results.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
SHUTTING DOWN & CLEAN-UP
Step1 Remove
Step2
Step3
Step4
detergent suction tube Turn off the engine. Turn off the water Press
trigger
to
from container and
insert into one gallon
of fresh water. Siphon
water at low pressure
for one minute.
source.
release
pressure.
water
Step5 Disconnect the
garden hose from the
water inlet on the unit.
Step6 Disconnect the high pressure hose from the high
pressure outlet and engage the gun safety lock.
TAKING A BREAK... five minutes or more
Step3 Engage gun safety
lock.
Step1 Turn off the engine. Step2 Press trigger to
release water pressure.
WINTERIZING AND LONG-TERM STORAGE
1. Disconnect all water connections.
5. Store the machine and accessories in
a room which does not reach freezing
temperatures. The machine should not
be placed near an open flame i.e.
furnace, hot water heater etc.
Caution: Failure to follow the above
directions will result in damage to the
pump assembly and accessories.
2. Start the machine for a few seconds,
until the water which had remained in
the pump exits. Turn off immediately.
3. Drain the gas and oil from the engine.
4. Do not allow high pressure hose to
become kinked.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
CLEANING TIPS
Deck Cleaning
Cement Patios,
Brick and Stone
(with or without detergent)
(with or without detergent)
Pre-rinse deck and surrounding area with
fresh water. If using Cub Cadet Deck
Wash, place detergent suction tube directly
into cleaning solution and apply to surface
at low pressure. For best results, limit your
work area to smaller sections of
approximately 25 square feet. Allow Cub
Cadet Deck Wash to remain on surface 1-3
minutes. Do not allow detergent to dry on
surface. Rinse at high pressure in a long
sweeping motion keeping the spray nozzle
approximately 3-6 inches from the cleaning
surface. Always clean from top to bottom
and from left to right. When moving on to a
new section of the cleaning surface, be
sure to overlap the previous section to
Pre-rinse cleaning surface with fresh water.
If using Cub Cadet All Purpose Cleaner,
place detergent suction tube directly into
cleaning solution and apply to surface at
low pressure. For best results, limit your
work area to smaller sections of
approximately 25 square feet. Allow Cub
Cadet All Purpose Cleaner to remain on
surface 1-3 minutes. Do not allow
detergent to dry on surface. Rinse at high
pressure in a sweeping motion keeping the
spray nozzle approximately 3-6 inches from
the cleaning surface. Always clean from top
to bottom and from left to right.
eliminate stop marks and ensure a more For removing extremely stubborn stains,
even cleaning result.
use the Cub Cadet Rotating Nozzle Spray
Wand.
Caution: Do not use rotating nozzle spray
wand on wood surface as it may cause
damage.
Cars, Boats & Motorcycles
(with or without detergent)
House Siding
(with or without detergent)
Pre-rinse vehicle with fresh water. If using
Cub Cadet Vehicle Wash, place detergent
suction tube directly into cleaning solution
and apply to surface at low pressure. For
best results, clean one side of vehicle at a
time and always apply detergent from
bottom to top, do not allow detergent to dry
on surface. If needed, use special Wash
Brush Attachment to remove stubborn dirt.
Pre-rinse cleaning surface with fresh water.
If using Cub Cadet All Purpose Cleaner,
place detergent suction tube directly into
cleaning solution and apply to surface at
low pressure (for best results, limit your
work area to sections of approximately 6
feet and always apply detergent from
bottom to top). Allow Cub Cadet All
Purpose Cleaner to remain on surface 1-3
minutes. Do not allow detergent to dry on
surface, if surface appears to be drying,
simply wet down surface with fresh water. If
needed, use special Wash Brush
Attachment to remove stubborn dirt. Rinse
at high pressure from top to bottom in an
even sweeping motion keeping the spray
nozzle approximately 6 inches from the
cleaning surface.
Rinse at high pressure in
motion keeping the spray
a
sweeping
nozzle
approximately 6-8 inches from the cleaning
surface (distance should increase when
rinsing pin-striping or other sensitive
surfaces). Always clean from top to bottom
and from left to right. For best results, wipe
surface dry with a chamois or soft dry cloth.
Caution: Do not use rotating nozzle spray
wand on vehicles as it may cause damage.
Caution: Do not use rotating nozzle spray
wand on siding as it may cause damage.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
CLEANING TIPS - continued
Barbecue Grills, Outdoor
Power Equipment &
Gardening Tools
Patio & Lawn Furniture
(with or without detergent)
Pre-rinse furniture and surrounding area
with fresh water. If using Cub Cadet All
Purpose Cleaner, place detergent suction
tube directly into cleaning solution and
apply to surface at low pressure. Allow Cub
Cadet All Purpose Cleaner to remain on
surface 1-3 minutes. Do not allow
detergent to dry on surface. If needed use
special Wash Brush Attachment to remove
stubborn dirt. Rinse at high pressure in a
sweeping motion keeping the spray nozzle
approximately 3-6 inches from the cleaning
surface. For best results, clean from top to
bottom and from left to right. Caution: Do
not use rotating nozzle spray wand on patio
or lawn furniture as it may cause damage.
(with or without detergent)
Pre-rinse cleaning surface with fresh water.
If using Cub Cadet All Purpose Cleaner or
Degreaser, place detergent suction tube
directly into cleaning solution and apply
detergent at low pressure. Allow Cub Cadet
detergent to remain on surface 1-3
minutes. Do not allow detergent to dry on
surface. Rinse at high pressure keeping the
spray nozzle approximately 3-6 inches from
the cleaning surface. For removing
extremely stubborn dirt, it may be
necessary to move the spray nozzle even
closer to the surface for greater dirt cutting
action. To remove caked on mud from
garbage cans, lawn mower blades, wheel
barrels or other non-sensitive metal
surfaces, you may want to use the Cub
Cadet Rotating Nozzle Spray Wand.
Recommendations
•
Before cleaning any surface an
inconspicuous area should be cleaned to
test spray pattern and distance for
maximum cleaning results.
Caution: Do not use rotating nozzle spray
wand on cloth, plastic or other sensitive
surfaces as it may cause damage.
•
If painted surfaces are pealing or
chipping, use extreme caution as
pressure washer may remove the loose
paint from the surface.
OPTIONAL CLEANING ACCESSORIES
To further enhance your cleaning capabilities, optional cleaning accessories are available
from your local Cub Cadet dealer:
•
•
•
•
•
Rotating Wash Brush
Wash Brush
Rotating Spray Wand
Extension Hose 25’
Plastic Hose Reel
Part No. KR-9103105
Part No. KR-9103106
Part No. KR-9103301
Part No. KR-9103006
Part No. KR-9103053
If you need help locating a dealer in your area, contact the Customer Dealer Referral Line
by calling:
1-877-835-7841
11
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
Symptom
Cause
Solution
Fill gas tank.
Add oil.
Engine will not start
No gasoline.
Low oil level.
Choke is not in correct
position.
Slide choke lever to “CHOKE”
position.
For additional engine
problems refer to the
engine owners
manual.
Engine throttle is not in
correct position.
Position the throttle to “FAST”.
Pressure built up in the
high pressure washer.
Squeeze the trigger to release the
pressure.
Unit does not reach
high pressure.
Diameter of garden hose is Replace with a 3/4 inch garden
too small.
hose.
Water supply is restricted.
Check garden hose for kinks, leaks
and blockage.
Not enough inlet water supply Open water source full force.
Water inlet filter is clogged. Remove filter and rinse out in warm
water.
Spray wand is in low
pressure position.
Turn spray wand tip to high
pressure position.
Output pressure
varies high and low.
Not enough inlet water supply. Turn water on full force. Check garden
hose for kinks, leaks or blockage.
Pump is sucking air.
Check that hoses and fittings are air
tight. Turn off machine and purge
pump by squeezing trigger gun until
a steady flow of water emerges
through the nozzle.
Water inlet filter is clogged. Remove filter and rinse out in warm
water.
Discharge nozzle is
obstructed.
Blow out or remove debris with a
fine needle.
Calcified gun, hose or
spray wand.
Run distilled vinegar through
detergent suction tube.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING - continued
Symptom
Cause
Solution
No detergent.
Detergent suction tube not Check connection.
properly connected to the
machine.
Detergent is too thick.
Dilute detergent, for best results
use Cub Cadet detergent.
The filter is closed.
Open the filter by turning it to the
desired detergent intake.
Filter on detergent suction Run warm water through filter to
tube is clogged.
remove debris.
Damaged or clogged
detergent suction tube.
Remove obstruction or replace
detergent suction tube.
Spray wand is in high
pressure position.
Turn spray wand tip to low pressure
position.
Discharge nozzle is
obstructed.
Blow out or remove debris with a
fine needle.
Garden hose
Loose fittings.
Tighten fittings.
connection leaks.
Missing/worn rubber
washer.
Insert new washer.
Spray wand or Spray Spray wand not properly
Insert the spray wand into the spray
wand extension. Carefully press in
against the spring tension and twist
into the locked position.
extension wand
leaks.
attached.
Spray wand extension not
properly attached.
Slide the spray wand extension into
the gun. Turn the wand collar
clockwise onto the gun threads until
tight.
Broken o-ring or plastic
insert.
Contact your local Cub Cadet
dealer.
Pump is noisy.
Pump is sucking air.
Check that hoses and fittings are air
tight. Turn off machine and purge
pump by squeezing trigger gun until
a steady flow of water emerges
through the nozzle.
Water leaks from
pump (up to 10 drops
per minute is
Loose fittings.
Check that all fittings are tight.
Thermal protection device Thermal protection device will
has been activated.
automatically reset.
permissible).
Water seals are damaged
or worn.
Contact your local Cub Cadet
dealer.
Oil Drip.
Oil seals are damaged or
worn.
Contact your local Cub Cadet
dealer.
• If you encounter any additional difficulties not listed, please contact your local Cub
Cadet dealer.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
MANUFACTURER’S LIMITED WARRANTY
for PRESSURE WASHERS
(RESIDENTIAL LINE)
The limited warranty set forth below is given by CUB CADET with respect to new
merchandise purchased and used in the United States, its possessions and territories.
CUB CADET warrants this product against defects in material and workmanship for a period
of one (1) year for residential users, commencing on the date of original purchase and will, at
its option, repair or replace, free of charge, any part found to be defective in material or
workmanship. This limited warranty shall only apply if this product has been operated and
maintained in accordance with the Operator’s Manual furnished with the product, and has not
been subject to misuse, abuse, neglect, accident, improper maintenance, improper storage or
handling, freezing, use of improper chemicals, alterations, vandalism, theft, fire, water, or
damage because of other peril or natural disaster. Damage resulting from the installation or
use of any accessory or attachment not approved by Cub Cadet for use with the product(s)
covered by this manual will void your warranty as to any resulting damages. The following
parts and accessories are subject to separate terms as follows: Limited Warranty: 90-day free
replacement for defects in materials and/or workmanship on hoses, hose reels, spray wands,
brushes, nozzles and/or similar approved accessories.
HOW TO OBTAIN SERVICE: Warranty service is available, WITH PROOF OF
PURCHASE, THROUGH YOUR LOCAL AUTHORIZED CUB CADET or CUB CADET
COMMERCIAL DEALER. To locate the dealer in your area, please check for a listing in
the Yellow Pages or contact CUB CADET by calling 877-835-7841 or writing to PO BOX
368023, Cleveland, Ohio 44136-9723.
This limited warranty does not provide coverage in the following cases:
(a) Routine maintenance items such as lubricants, filters, tune-ups, or adjustments.
(b) Equipment setup, normal wear parts or components.
(c) CUB CADET does not extend any warranty for products sold or exported outside
of the United States, its possessions, and territories.
No implied warranty, including any implied warranty of merchantability or fitness for a
particular purpose, applies after the applicable period of express written warranty
above. No other express warranty or guaranty, whether written or oral, except as
mentioned above, given by any person or entity, including the dealer with respect to any
product shall bind CUB CADET. During the period of the Warranty, the exclusive remedy
is repair or replacement of the product as set forth above. (Some states do not allow
limitations on how long an implied warranty lasts, so the above limitation may not apply to you.)
The provisions as set forth in this Warranty provide the sole and exclusive remedy
arising for the sale. CUB CADET shall not be liable for incidental or consequential loss
or damages including, without limitation, to any claim for loss of profits, loss of
savings or revenue, loss of the use of the equipment or any associated equipment.,
facilities or service, downtime, the claims or costs of third parties including customers,
and injury to property, and further including expenses incurred for substitute or
replacement property care services, for transportation or for related expenses, or for
rental expenses to temporarily replace a warranted product. (Some states do not allow
the exclusion or limitation of incidental or consequential damages, so the above exclusion may
not apply to you.)
In no event shall recovery of any kind be greater than the amount of the purchase price of
the product sold. Alteration of the safety features of the product shall void this warranty. You
assume the risk and liability for loss, damage, or injury to you and your property and/or to
others and their property arising out of use or misuse or inability to use this product.
This limited warranty shall not extend to anyone other than the original purchaser or original lessee,
or the person for whom it was purchased as a gift.
HOW STATE LAW RELATES to this WARRANTY: This limited warranty gives you
specific legal rights, and you may also have other rights which vary from state to state.
Download from Www.Somanuals.com. All Manuals Search And Download.
|