Safe Operation Practices • Set-Up • Operation • Maintenance • Service • Troubleshooting • Warranty
OperatOr’s Manual
GT 2000, GTX 2000 & GTX 2100
WARNING
READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS IN THIS MANUAL
BEFORE ATTEMPTING TO OPERATE THIS MACHINE.
FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY.
CUB CADET LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019
Printed In USA
Form No. 769-08611
(November 2, 2012)
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safe Operation Practices
2
WARNING! This symbol points out important safety instructions which, if not followed,
could endanger the personal safety and/or property of yourself and others. Read and follow
all instructions in this manual before attempting to operate this machine. Failure to comply
with these instructions may result in personal injury.
When you see this symbol. HEED ITS WARNING!
CALIFORNIA PROPOSITION 65
WARNING! Engine Exhaust, some of its constituents, and certain vehicle components
contain or emit chemicals known to State of California to cause cancer and birth defects
or other reproductive harm.
WARNING! Battery posts, terminals, and related accessories contain lead and lead
compounds, chemicals known to the State of California to cause cancer and reproductive
harm. Wash hands after handling
DANGER! This machine was built to be operated according to the safe operation practices in
this manual. As with any type of power equipment, carelessness or error on the part of the
operator can result in serious injury. This machine is capable of amputating hands and feet
and throwing objects. Failure to observe the following safety instructions could result in
serious injury or death.
6.
Thoroughly inspect the area where the equipment is to be
used. Remove all stones, sticks, wire, bones, toys, and other
foreign objects which could be picked up and thrown by
the blade(s). Thrown objects can cause serious personal
injury.
General Operation
1.
Read, understand, and follow all instructions on the
machine and in the manual(s) before attempting to
assemble and operate. Keep this manual in a safe place for
future and regular reference and for ordering replacement
parts.
7.
Plan your mowing pattern to avoid discharge of material
toward roads, sidewalks, bystanders and the like. Also,
avoid discharging material against a wall or obstruction
which may cause discharged material to ricochet back
toward the operator.
2.
Be familiar with all controls and their proper operation.
Know how to stop the machine and disengage them
quickly.
3.
Never allow children under 14 years of age to operate this
machine. Children 14 and over should read and understand
the instructions and safe operation practices in this manual
and on the machine and should be trained and supervised
by an adult.
8.
9.
Always wear safety glasses or safety goggles during
operation and while performing an adjustment or repair
to protect your eyes. Thrown objects which ricochet can
cause serious injury to the eyes.
Wear sturdy, rough-soled work shoes and close-fitting
slacks and shirts. Loose fitting clothes and jewelry can be
caught in movable parts. Never operate this machine in
bare feet or sandals.
4.
5.
Never allow adults to operate this machine without proper
instruction.
To help avoid blade contact or a thrown object injury,
keep bystanders, helpers, children and pets at least 75 feet
from the machine while it is in operation. Stop machine if
anyone enters the area.
10. Be aware of the mower and attachment discharge direction
and do not point it at anyone. Do not operate the mower
without the discharge cover or entire grass catcher in its
proper place.
11. Do not put hands or feet near rotating parts or under the
cutting deck. Contact with the blade(s) can amputate
hands and feet.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
12. A missing or damaged discharge cover can cause blade
Slope Operation
contact or thrown object injuries.
Slopes are a major factor related to loss of control and tip-over
accidents which can result in severe injury or death. All slopes
require extra caution. If you cannot back up the slope or if you
feel uneasy on it, do not mow it.
13. Stop the blade(s) when crossing gravel drives, walks, or
roads and while not cutting grass.
14. Watch for traffic when operating near or crossing
roadways. This machine is not intended for use on any
public roadway.
For your safety, use the slope gauge included as part of this
manual to measure slopes before operating this machine on
a sloped or hilly area. If the slope is greater than 15 degrees as
shown on the slope gauge, do not operate this machine on that
area or serious injury could result.
15. Do not operate the machine while under the influence of
alcohol or drugs.
16. Mow only in daylight or good artificial light.
17. Never carry passengers.
Do:
1.
Mow up and down slopes, not across. Exercise extreme
caution when changing direction on slopes.
18. Disengage blade(s) before shifting into reverse. Back up
slowly. Always look down and behind before and while
backing to avoid a back-over accident.
2.
Watch for holes, ruts, bumps, rocks, or other hidden
objects. Uneven terrain could overturn the machine. Tall
grass can hide obstacles.
19. Slow down before turning. Operate the machine smoothly.
Avoid erratic operation and excessive speed.
3.
Use slow speed. Choose a low enough speed setting so
that you will not have to stop or shift while on the slope.
Tires may lose traction on slopes even though the brakes
are functioning properly. Always keep machine in gear
when going down slopes to take advantage of engine
braking action.
20. Disengage blade(s), set parking brake, stop engine and wait
until the blade(s) come to a complete stop before removing
grass catcher, emptying grass, unclogging chute, removing
any grass or debris, or making any adjustments.
21. Never leave a running machine unattended. Always turn
off blade(s), place transmission in neutral, set parking
brake, stop engine and remove key before dismounting.
4.
5.
6.
Follow the manufacturer’s recommendations for wheel
weights or counterweights to improve stability.
22. Use extra care when loading or unloading the machine into
a trailer or truck. This machine should not be driven up or
down ramp(s), because the machine could tip over, causing
serious personal injury. The machine must be pushed
manually on ramp(s) to load or unload properly.
Use extra care with grass catchers or other attachments.
These can change the stability of the machine.
Keep all movement on the slopes slow and gradual. Do
not make sudden changes in speed or direction. Rapid
engagement or braking could cause the front of the
machine to lift and rapidly flip over backwards which could
cause serious injury.
23. Muffler and engine become hot and can cause a burn. Do
not touch.
24. Check overhead clearances carefully before driving under
low hanging tree branches, wires, door openings etc.,
where the operator may be struck or pulled from the
machine, which could result in serious injury.
7.
Avoid starting or stopping on a slope. If tires lose traction,
disengage the blade(s) and proceed slowly straight down
the slope.
25. Disengage all attachment clutches, depress the brake
pedal completely and shift into neutral before attempting
to start engine.
Do Not:
1.
Do not turn on slopes unless necessary; then, turn slowly
and gradually downhill, if possible.
26. Your machine is designed to cut normal residential grass of
a height no more than 10”. Do not attempt to mow through
unusually tall, dry grass (e.g., pasture) or piles of dry leaves.
Dry grass or leaves may contact the engine exhaust and/
or build up on the mower deck presenting a potential fire
hazard.
2.
Do not mow near drop-offs, ditches or embankments. The
mower could suddenly turn over if a wheel is over the edge
of a cliff, ditch, or if an edge caves in.
3.
Do not try to stabilize the machine by putting your foot on
the ground.
4.
5.
Do not use a grass catcher on steep slopes.
27. Use only accessories and attachments approved for this
machine by the machine manufacturer. Read, understand
and follow all instructions provided with the approved
accessory or attachment.
Do not mow on wet grass. Reduced traction could cause
sliding.
6.
7.
Do not shift to neutral and coast downhill. Over-speeding
may cause the operator to lose control of the machine
resulting in serious injury or death.
28. Data indicates that operators, age 60 years and above, are
involved in a large percentage of riding mower-related
injuries. These operators should evaluate their ability
to operate the riding mower safely enough to protect
themselves and others from serious injury.
Do not tow heavy pull behind attachments (e.g. loaded
dump cart, lawn roller, etc.) on slopes greater than 5
degrees. When going down hill, the extra weight tends
to push the tractor and may cause you to loose control
(e.g. tractor may speed up, braking and steering ability are
reduced, attachment may jack-knife and cause tractor to
overturn).
29. If situations occur which are not covered in this manual, use
care and good judgment. Contact your customer service
representative for assistance.
4
Section 2 — important Safe operation practiceS
Download from Www.Somanuals.com. All Manuals Search And Download.
Children
Service
1.
Tragic accidents can occur if the operator is not alert to the
Safe Handling of Gasoline:
presence of children. Children are often attracted to the
machine and the mowing activity. They do not understand
the dangers. Never assume that children will remain where
you last saw them.
1.
To avoid personal injury or property damage use extreme
care in handling gasoline. Gasoline is extremely
flammable and the vapors are explosive. Serious
personal injury can occur when gasoline is spilled on
yourself or your clothes which can ignite. Wash your skin
and change clothes immediately.
a. Keep children out of the mowing area and in
watchful care of a responsible adult other than the
operator.
a. Use only an approved gasoline container.
b. Be alert and turn machine off if a child enters the
area.
b. Never fill containers inside a vehicle or on a truck
or trailer bed with a plastic liner. Always place
containers on the ground away from your vehicle
before filling.
c. Before and while backing, look behind and down for
small children.
d. Never carry children, even with the blade(s) shut off.
They may fall off and be seriously injured or interfere
with safe machine operation.
c. When practical, remove gas-powered equipment
from the truck or trailer and refuel it on the ground.
If this is not possible, then refuel such equipment on
a trailer with a portable container, rather than from a
gasoline dispenser nozzle.
e. Use extreme care when approaching blind corners,
doorways, shrubs, trees or other objects that may
block your vision of a child who may run into the
path of the machine.
d. Keep the nozzle in contact with the rim of the fuel
tank or container opening at all times until fueling is
complete. Do not use a nozzle lock-open device.
f.
To avoid back-over accidents, always disengage
the cutting blade(s) before shifting into Reverse. If
equipped, the “Reverse Caution Mode” should not
be used when children or others are around.
e. Extinguish all cigarettes, cigars, pipes and other
sources of ignition.
f.
Never fuel machine indoors.
g. Keep children away from hot or running engines.
They can suffer burns from a hot muffler.
g. Never remove gas cap or add fuel while the engine
is hot or running. Allow engine to cool at least two
minutes before refueling.
h. Remove key when machine is unattended to
prevent unauthorized operation.
h. Never over fill fuel tank. Fill tank to no more than
the bottom of filler neck to allow space for fuel
expansion.
2.
Never allow children under 14 years of age to operate this
machine. Children 14 and over should read and understand
the instructions and safe operation practices in this manual
and on the machine and should be trained and supervised
by an adult.
i.
j.
Replace gasoline cap and tighten securely.
If gasoline is spilled, wipe it off the engine and
equipment. Move machine to another area. Wait 5
minutes before starting the engine.
Towing
1.
Tow only with a machine that has a hitch designed for
towing. Do not attach towed equipment except at the
hitch point.
k. To reduce fire hazards, keep machine free of grass,
leaves, or other debris build-up. Clean up oil or fuel
spillage and remove any fuel soaked debris.
2.
Follow the manufacturers recommendation for weight
limits for towed equipment and towing on slopes.
l.
Never store the machine or fuel container inside
where there is an open flame, spark or pilot light
as on a water heater, space heater, furnace, clothes
dryer or other gas appliances.
3.
Never allow children or others in or on towed equipment.
4.
On slopes, the weight of the towed equipment may cause
loss of traction and loss of control.
m. Allow a machine to cool at least five minutes before
storing.
5.
Always use extra caution when towing with a machine
capable of making tight turns (e.g. “zero-turn” ride-on
mower). Make wide turns to avoid jack-knifing.
General Service
1.
Never run an engine indoors or in a poorly ventilated area.
Engine exhaust contains carbon monoxide, an odorless,
and deadly gas.
6.
7.
Travel slowly and allow extra distance to stop.
Do not shift to neutral and coast downhill.
2.
Before cleaning, repairing, or inspecting, make certain the
blade(s) and all moving parts have stopped. Disconnect the
spark plug wire and ground against the engine to prevent
unintended starting.
Section 2 — important Safe operation practiceS
5
Download from Www.Somanuals.com. All Manuals Search And Download.
3.
Periodically check to make sure the blades come to
complete stop within approximately (5) five seconds after
operating the blade disengagement control. If the blades
do not stop within the this time frame, your machine
should be serviced professionally by an authorized Cub
Cadet Service Dealer.
Do not modify engine
To avoid serious injury or death, do not modify engine in any
way. Tampering with the governor setting can lead to a runaway
engine and cause it to operate at unsafe speeds. Never tamper
with factory setting of engine governor.
4.
5.
Check brake operation frequently as it is subjected to wear
during normal operation. Adjust and service as required.
Notice Regarding Emissions
Engines which are certified to comply with California and federal
EPA emission regulations for SORE (Small Off Road Equipment)
are certified to operate on regular unleaded gasoline, and
may include the following emission control systems: Engine
Modification (EM), Oxidizing Catalyst (OC), Secondary Air
Injection (SAI) and Three Way Catalyst (TWC) if so equipped.
Check the blade(s) and engine mounting bolts at frequent
intervals for proper tightness. Also, visually inspect blade(s)
for damage (e.g., excessive wear, bent, cracked). Replace
the blade(s) with the original equipment manufacturer’s
(O.E.M.) blade(s) only, listed in this manual. “Use of parts
which do not meet the original equipment specifications
may lead to improper performance and compromise
safety!”
When required, models are equipped with low permeation fuel
lines and fuel tanks for evaporative emission control. California
models may also include a carbon canister. Please contact
Customer Support for information regarding the evaporative
emission control configuration for your model.
6.
7.
Mower blades are sharp. Wrap the blade or wear gloves,
and use extra caution when servicing them.
Keep all nuts, bolts, and screws tight to be sure the
equipment is in safe working condition.
Spark Arrestor
8.
9.
Never tamper with the safety interlock system or other
safety devices. Check their proper operation regularly.
WARNING! This machine is equipped with an
internal combustion engine and should not be used
on or near any unimproved forest-covered,
brushcovered or grass-covered land unless the
engine’s exhaust system is equipped with a spark
arrestor meeting applicable local or state laws (if
any).
After striking a foreign object, stop the engine, disconnect
the spark plug wire(s) and ground against the engine.
Thoroughly inspect the machine for any damage. Repair
the damage before starting and operating.
10. Never attempt to make adjustments or repairs to the
If a spark arrestor is used, it should be maintained in effective
working order by the operator. In the State of California the
above is required by law (Section 4442 of the California Public
Resources Code). Other states may have similar laws. Federal laws
apply on federal lands.
A spark arrestor for the muffler is available through your
nearest engine authorized service dealer or contact the service
department, P.O. Box 361131 Cleveland, Ohio 44136-0019.
machine while the engine is running.
11. Grass catcher components and the discharge cover are
subject to wear and damage which could expose moving
parts or allow objects to be thrown. For safety protection,
frequently check components and replace immediately
with original equipment manufacturer’s (O.E.M.) parts only,
listed in this manual. “Use of parts which do not meet the
original equipment specifications may lead to improper
performance and compromise safety!”
12. Do not change the engine governor settings or over-speed
the engine. The governor controls the maximum safe
operating speed of the engine.
13. Maintain or replace safety and instruction labels, as
necessary.
14. Observe proper disposal laws and regulations for gas, oil,
etc. to protect the environment.
15. According to the Consumer Products Safety Commission
(CPSC) and the U.S. Environmental Protection Agency (EPA),
this product has an Average Useful Life of seven (7) years,
or 390 hours of operation. At the end of the Average Useful
Life have the machine inspected annually by an authorized
service dealer to ensure that all mechanical and safety
systems are working properly and not worn excessively.
Failure to do so can result in accidents, injuries or death.
WARNING! Your Responsibility—Restrict the use of this power machine to persons who read, understand and
follow the warnings and instructions in this manual and on the machine.
SAVE THESE INSTRUCTIONS!
6
Section 2 — important Safe operation practiceS
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Symbols
This page depicts and describes safety symbols that may appear on this product. Read, understand, and follow all instructions on the
machine before attempting to assemble and operate.
Symbol
Description
READ THE OPERATOR’S MANUAL(S)
Read, understand, and follow all instructions in the manual(s) before attempting to
assemble and operate
DANGER— ROTATING BLADES
Never carry passengers. Never carry children, even with the blades off.
DANGER— ROTATING BLADES
Always look down and behind before and while backing to avoid a back-over accident.
WARNING— ROTATING BLADES
Do not put hands or feet near rotating parts or under the cutting deck. Contact with the
blade(s) can amputate hands and feet.
WARNING—THROWN OBJECTS
This machine may pick up and throw and objects which can cause serious personal injury.
WARNING—THROWN OBJECTS
This machine may pick up and throw and objects which can cause serious personal injury.
BYSTANDERS
Keep bystanders, helpers, children and pets at least 75 feet from the machine while it is in
operation.
WARNING— SLOPE OPERATION
Do not operate this machine on a slope greater than 15 degrees.
WARNING— HOT SURFACE
Engine parts, especially the muffler, become extremely hot during operation. Allow engine
and muffler to cool before touching.
DANGER — ROTATING BLADES
To reduce the risk of injury, keep hands and feet away. Do not operate unless discharge cover
or grass catcher is in its proper place. If damaged, replace immediately.
WARNING— TOWING
Avoid jack-knifing when towing, go slow and make wide turns.
Section 2 — important Safe operation practiceS
7
Download from Www.Somanuals.com. All Manuals Search And Download.
8
Section 2 — important Safe operation practiceS
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly & Set-Up
3
Contents of Crate
•
One Garden Tractor
•
One Operator’s Manual
•
One Engine Operator’s Manual
NOTE: This Operator’s Manual covers several models. Tractor
features may vary by model. Not all features in this manual are
applicable to all tractor models and the tractor depicted may
differ from yours.
Connecting the Battery Cables
CALIFORNIA PROPOSITION 65 WARNING!
Battery posts, terminals, and related accessories
contain lead and lead compounds, chemicals known
to the State of California to cause cancer and
reproductive harm. Wash hands after handling.
Tractor Set-Up
Moving The Tractor Manually
CAUTION: When attaching battery cables, always
connect the POSITIVE (red) wire to its terminal first,
followed by the NEGATIVE (black) wire.
Your tractor’s transmission is equipped with a hydrostatic
relief valve for occasions when it is necessary to move the
tractor manually. Opening this valve permits the fluid in the
transmission to bypass its normal route, allowing the rear tires
to “freewheel.” To open the hydrostatic relief valve, proceed as
follows:
For shipping reasons, both battery cables on your equipment
may have been left disconnected from the terminals at the
factory. To connect the battery cables, proceed as follows:
NOTE: The positive battery terminal is marked Positive (+). The
negative battery terminal is marked Negative (–).
1.
Locate the hydrostatic bypass rod in the rear of the tractor.
See Figure 3-1.
1.
Remove the plastic cover, if present, from the positive (+)
battery terminal and attach the red cable to the positive (+)
battery terminal with the bolt and hex nut. See Figure 3-2.
Figure 3-1
2.
Pull the hydrostatic bypass rod down, outward and then up
to lock it in place.
Figure 3-2
NOTE: If the tractor will not move or does not move freely when
pushing check if the bypass lever is fully open.
2.
Remove the plastic cover, if present, from the negative (–)
battery terminal and attach the black cable to the negative
(–) battery terminal with the bolt and hex nut. See Figure 3-2.
NOTE: The transmission will NOT engage when the hydrostatic
bypass rod is pulled out. Return the rod to its normal position
prior to operating the tractor. If the tractor will not move when
pushing on the forward/reverse pedals, or moves slowly, check to
see of the bypass valve is on.
3.
Position the red rubber boot over the positive (+) battery
terminal to help protect it from corrosion.
NOTE: If the battery is put into service after the date shown on
top or side of battery, charge the battery as instructed in the
Maintenance section your Operator’s Manual prior to operating the
tractor.
CAUTION: Never attempt to move the tractor
manually without first opening the hydrostatic relief
valve. Doing so will result in serious damage to the
tractor’s transmission.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Checking Tire Pressure
Gas and Oil
The fuel tank is located at the rear of the tractor and holds
4-1⁄2 gallons of gas. Remove the fuel cap by turning it counter-
clockwise. Use only clean, fresh (no more than 30 days old),
unleaded gasoline. Fill the tank no higher the bottom of the fill
neck to allow space for fuel expansion.
WARNING! Maximum tire pressure under any
circumstances is 10 psi on rear tires and 12 psi on
front tires. Equal tire pressure should be maintained
at all times.
The tires on your tractor may be over-inflated for shipping
purposes. Reduce the tire pressure before operating the tractor.
Recommended operating tire pressure is approximately 10 p.s.i.
for the rear tires & 12 psi for the front tires. Check sidewall of tire
for maximum psi.
WARNING! Use extreme care when handling
gasoline. Gasoline is extremely flammable and the
vapors are explosive. Never fuel the machine
indoors or while the engine is hot or running.
Extinguish cigarettes, cigars, pipes and other
sources of ignition.
Adjusting the Seat
To adjust the position of the seat, push the seat adjustment lever
to the left. Slide the seat forward or rearward to the desired
position; then release the adjustment lever. Make sure seat is
locked into position before operating the tractor. See Figure 3-3.
NOTE: Your tractor is shipped with oil in the engine. However,
you MUST check the oil level before operating.
CAUTION: Always check the engine oil level before
each use as instructed in the Kohler Owner’s Manual.
Add oil as necessary. Failure to do so may result in
serious damage to your engine
Figure 3-3
10
Section 2 — ASSembly & Set-Up
Download from Www.Somanuals.com. All Manuals Search And Download.
Controls & Features
4
Hour Meter/Service Indicator
PTO/Blade Engage Lever
Choke Control
Cruise Control/
Parking Brake Lever
Throttle Control
Ignition Switch Module
Forward Drive Pedal
Brake Pedal
Steering Tilt Lever
Reverse Drive Pedal
Electric Lift Switch
Cup Holder
Storage Compartment
Fuel Cap
Manual Lift
Handle
Cutting Height Lever
Low Gas Window
Hydrostatic Transmission
Dipstick/Fill Tube
Transmission
Bypass Rod
Throttle Control Lever
The throttle control lever is located on the left side of
Garden Tractor controls and features are illustrated in Fig 4-1 and
described on the following pages.
FAST
NOTE: This Operator’s Manual covers several models. Tractor
features may vary by model. Not all features in this manual are
applicable to all tractor models and the tractor depicted may
differ from yours.
the tractor’s dash panel and slides between the FAST
(rabbit) and SLOW
(turtle) positions. This
lever controls the speed of the engine. When set in
a given position, the throttle will maintain a uniform
engine speed.
WARNING! Read and follow all safety rules and
instructions in this manual, including the entire
Operation section, before attempting to operate
this machine. Failure to comply with all safety rules
and instructions may result in personal injury.
NOTE: When operating the tractor be certain that
the throttle lever is always in the FAST
(rabbit)
position. Operating with the throttle at less than full
throttle may lead to shortened battery life and poor
cut quality.
SLOW
Choke Control
The choke control can be found on the left side
of the dash panel and is activated by sliding the
lever forward. Activating the choke control closes
the choke plate on the carburetor and aids in
starting the engine. Refer to Starting The Engine in the Operation
section of this manual for detailed starting instructions.
Brake Pedal
The brake pedal is located on the left
front side of the tractor. The brake pedal
can be used for sudden stops or setting
the parking brake.
NOTE: The brake pedal must be fully depressed to activate the
safety interlock switch when starting the tractor.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Manual Lift Lever (If so equipped)
Forward Drive Pedal
The forward drive pedal is located on the right side
of the tractor, along the running board. Press the
drive pedal forward to cause the tractor to travel
forward. Ground speed is also controlled with
the drive pedal. The further forward the pedal is
pivoted, the faster the tractor will travel. The pedal
will return to its original position when it’s not
pressed.
The lift lever is located in the right fender and is used to raise
and lower the deck. Pull the handle to the left out of the index
notch and push downward to lower the deck, or pull upward to
raise the deck. When the desired height is attained, move the lift
handle to the right until fully in the index notch.
Reverse Pedal
The reverse drive pedal is located on the right side of
the tractor along the running board. Ground speed
is also controlled with the reverse pedal. The further
downward the pedal is pivoted, the faster the tractor
will travel. The pedal will return to its original position
when it’s not pressed.
Electric Lift Switch (If so equipped)
nt
djustme
eight A
ck Lift H
tric De
ate Elec
To Oper
Raise Ele
ion.
Lift
ighe
st Posit
To The H
eck Lift
ctric D
ic Deck
r Electr
t. Lowe
ing Heigh
Set Cutt
ion.
g Posit
n Cuttin
To Chose
PTO/Blade Engage Lever
Activating the PTO engages power to the cutting
deck or other (separately available) attachments.
Lift up on the PTO/Blade Engage lever to activate
it. Push down on the PTO/ Blade Engage lever to
disengage the power to the cutting deck or other
(separately available) attachments.
The electric lift switch located in the right fender and is used to
raise and lower the deck. To lower the deck press down on the
front of the switch and to raise the deck push down on the rear of
the switch.
Cutting Height Lever (If so equipped)
NOTE: The PTO/Blade Engage lever must be in
the disengaged (OFF) position when starting the
engine.
LO
1
2
3
4
5
HI
The cutting height lever is used to set the distance the deck can
be lowered. The cutting height lever can be set to six different
positions by moving the lever up or down to the desired setting.
Parking Brake/Cruise Control Lever
Ignition Switch Module
The parking brake/cruise control lever is located
on the left of the tractor’s dash panel. It is used
to engage the parking brake when the tractor is
at rest. Engaging the lever while the tractor is in
motion allows the tractor to remain at a constant
ground speed without applying pressure to the
forward drive pedal. Refer to the Operation section
of this manual for detailed instructions regarding
the parking brake as well as the cruise control
feature.
WARNING! Never
leave a running
machine unattended.
Always disengage
PTO, set parking brake, stop
engine and remove key to prevent
unintended starting.
To start the engine, insert the
key into the ignition switch and
NOTE: Cruise control can NOT be engaged at the
tractor’s fastest ground speed. If the operator should attempt
to do so, the tractor will automatically decelerate to the fastest
optimal mowing ground speed
turn clockwise to the START
position. Release the key into the
NORMAL MOWING MODE
position once the engine has
fired.
NOTE: The parking brake must be set if the operator leaves the
seat with the engine running or the engine will automatically
shut off.
To stop the engine, turn the ignition key counterclockwise to the
STOP position.
CAUTION: Prior to operating the tractor, refer to
WARNING! Never leave a running machine
unattended. Always disengage PTO, set parking
brake, stop engine and remove key to prevent
unintended starting.
both Safety Interlock Switches and Starting The
Engine in the Operation section of this manual for
detailed instructions regarding the Ignition Switch
Module and operating the tractor in REVERSE
CAUTION MODE
.
12
Section 4 — controlS & FeatureS
Download from Www.Somanuals.com. All Manuals Search And Download.
LCD
Low Gas Window
The low gas window is located at the rear of
the tractor. If the gas level is visible in this
window, the tank should be re-filled.
FILL TANK IF GAS
LEVEL IS SHOWN
IN WINDOW
When the ignition key is rotated out of the STOP position but not
into the START position, the systems indicator monitor displays the
battery’s output, in volts, on its LCD for approximately five seconds,
after which it displays an hour glass and the hours of tractor
operation. Once the tractor is started, the monitor continually
displays an hour glass and the hours of tractor operation on its LCD.
Transmission Bypass Rod
The transmission bypass rod is located at the rear of the tractor
on the lower right section of the frame.
NOTE: Hours of tractor operation are recorded any time the
ignition key is rotated out of the STOP position, regardless of
whether the engine is started.
The Indicator Monitor will also remind the operator of
When engaged, the rod opens a bypass within the hydrostatic
transmissions, which allows the tractor to be pushed short
distances by hand. Refer to the Assembly & Set-Up section for
instructions on using the bypass feature.
maintenance intervals for changing the engine oil. The LCD will
alternately flash the recorded hours, “CHG” and “OIL” for five
minutes, after every 50 hours of recorded operation elapse. The
maintenance interval lasts for two hours (from 50-52, 100-102,
150-152, etc.). The LCD will also flash as described above for five
minutes every time the tractor’s engine has been started during
this maintenance interval. Before the interval expires, change the
engine oil as instructed in the Engine Operator’s Manual.
NOTE: If the tractor will not move or does not move freely when
pushing check if the bypass lever is fully open.
NOTE: The transmission will NOT engage when the hydrostatic
bypass rod is pulled out. Return the rod to its normal position
prior to operating the tractor. If the tractor will not move when
pushing on the forward/reverse pedals, or moves slowly, check to
see of the bypass valve is on.
Brake
CAUTION: Never tow your tractor. Towing the
tractor with the rear wheels on the ground may
cause severe damage to the transmissions.
If the Brake light illuminates when attempting to start the
tractor’s engine, depress the brake pedal.
Hydrostatic Transmission Oil Plug/Dipstick
PTO (Blade Engage)
The hydrostatic transmission oil plug/dipstick is located on the
back of the tractor frame and is used to check the level of the
hydrostatic transmission oil. The oil fill port is where hydrostatic
transmission oil can be added.
Systems Indicator Monitor/Hour Meter
If the PTO light illuminates when attempting to start the tractor’s
engine, move PTO lever into the disengaged (OFF) position.
Oil
BATT.
OIL
It is normal for the Oil light to illuminate while the engine is
cranking during start-up, but if it illuminate’s during operation,
while the engine is running, stop the tractor immediately and
check the engine oil level as instructed in this Owner’s Manual.
PTO /
BLADE
PARK
BRAKE
Battery
It is normal for the Battery light to illuminate while the engine is
cranking during start-up, but if it illuminate’s during operation,
while the engine is running, the battery is in need of a charge
or the engine’s charging system is not generating sufficient
amperage. Charge the battery as instructed in the Service
section of this manual or have the charging system checked by
your Cub Cadet dealer.
Section 4 — controlS & FeatureS
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
5
5.
6.
Move the throttle control lever to midway between the
FAST and SLOW positions.
NOTE: When operating the tractor be certain that the
throttle lever is always in the FAST (rabbit) position.
WARNING! Avoid serious injury or death. Go up
and down slopes, not across. Avoid sudden turns.
Do not operate unit where it could slip or tip. If
machine stops going uphill, stop PTO and back
down the hill safely. Keep safety devices (guards,
shields and switches) in place and working. Remove
objects that could be thrown by the blades. Know
location and function of all controls. Be sure the
blades and the engine are stopped before placing
hands or feet near blades. Before leaving operator’s
position, disengage PTO, engage brake lock, shut off
and remove key.
Operating with the throttle at less than full throttle may
lead to shortened battery life.
Turn the ignition key clockwise to the START
After the engine starts, release the key. It will return to the
NORMAL MOWING position.
position.
CAUTION: Do NOT hold the key in the START
position for longer than ten seconds at a time. Doing
so may cause damage to your engine’s electric
starter.
Safety Interlock Switches
This tractor is equipped with a safety interlock system for the
protection of the operator. If the interlock system should ever
malfunction, do not operate tractor. Contact your Cub Cadet dealer.
6.
After the engine starts, deactivate the choke control.
NOTE: Do NOT leave the choke control on while operating the
tractor. Doing so will result in a “rich” fuel mixture and cause the
engine to run poorly.
•
The safety interlock system prevents the engine from
cranking or starting unless the parking brake is engaged,
and the PTO (Blade Engage) knob is in the disengaged
(OFF) position.
Stopping the Engine
•
•
The engine will automatically shut off if the operator leaves
the seat before engaging the parking brake.
WARNING! If you strike a foreign object, stop the
engine and disconnect the spark plug wire(s).
Thoroughly inspect the machine for any damage.
Repair the damage before restarting and operating
The electric PTO (Blade Engage) clutch will automatically
shuts off if the operator leaves the tractor’s seat with the
PTO (Blade Engage) knob in the engaged (ON) position,
regardless of whether the parking brake is engaged.
1.
If the blades are engaged, place the PTO/Blade Engage
lever in the OFF position.
Place the throttle control near the SLOW
•
With the ignition key in the NORMAL MOWING position,
the electric PTO (Blade Engage) clutch will automatically
shut off if the PTO (Blade Engage) knob is moved into the
engaged (ON) position with the drive pedal in position for
Reverse travel.
2.
position
3.
Turn the ignition key counterclockwise to the STOP
position.
4.
Remove the key from the ignition switch to prevent
unintended starting.
WARNING! Do not operate the tractor if the
interlock system is malfunctioning. This system was
designed for your safety and protection.
Starting the Engine
WARNING! Do not operate the tractor if the
interlock system is malfunctioning. This system was
designed for your safety and protection.
NOTE: Refer to the Assembly & Set-up section of this manual for
Gasoline and Oil fill-up instructions.
1.
2.
3.
4.
Insert the tractor key into the ignition switch module.
Place the PTO/Blade Engage lever to OFF position.
Engage the tractor’s parking brake
.
Push the choke control upward into the choke on
position.
NOTE: If the engine is warmed up, it may not be necessary
to place the choke control in the choke position.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Reverse Caution Mode
Driving The Tractor
WARNING! Avoid sudden starts, excessive speed
and sudden stops.
The REVERSE CAUTION MODE
module allows the tractor to be operated in reverse with the
position of the key switch
blades (PTO) engaged.
NOTE: Mowing in reverse is not recommended.
1.
Lightly press the brake pedal
to release the parking brake
position.
WARNING! Use extreme caution while operating
the tractor in the REVERSE CAUTION MODE
Always look down and behind before and while
backing. Do not operate the tractor when children
or others are around. Stop the tractor immediately if
someone enters the area.
. Move the throttle lever into the FAST
.
2.
To travel FORWARD, slowly press the forward drive pedal
forward until the desired speed is achieved. See Figure 5-2.
To use the REVERSE CAUTION MODE
:
NOTE: The operator MUST be seated in the tractor seat.
1.
Start the engine as previously instructed on the previous
page.
2.
Turn the key from the NORMAL MOWING
position to the REVERSE CAUTION MODE
(Green)
(Yellow)
position of the key switch module. See Figure 5-1.
Forward Drive Pedal
Reverse Drive Pedal
Reverse
Push Button
Indicator
Light
Reverse
Caution Mode
Position
Stop
Position
Figure 5-2
Start
Position
3.
To travel in REVERSE, check that the area behind is clear then
slowly depress the reverse drive pedal until the desired
speed is achieved. See Figure 5-2.
CAUTION: Do NOT attempt to change the
direction of travel when the tractor is in motion.
Always bring the tractor to a complete stop before
changing from forward to reverse or vice versa.
WARNING! Do not leave the seat of the tractor
without first placing the PTO/Blade Engage lever in
the OFF position and engaging the parking brake. If
leaving the tractor unattended, also turn the engine
off and remove the ignition key.
Figure 5-1
Press the REVERSE PUSH BUTTON
3.
at the top, right
corner of the key switch module. The red indicator light
at the top, left corner of the key switch module will be ON
while activated. See Figure 5-1.
4.
5.
Once activated (indicator light ON), the tractor can be
driven in reverse with the cutting blades (PTO) engaged.
Always look down and behind before and while backing to
make sure no children are around. After resuming forward
motion, return key to the NORMAL MOWING
position.
The REVERSE CAUTION MODE
will remain activated until:
a. The key is placed in either the NORMAL MOWING
position or STOP position or
b. The operator leaves the seat.
Section 5 — operation
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Driving On Slopes
Setting The Cruise Control
Refer to the SLOPE GAUGE on page 8 to help determine slopes
where you may operate the tractor safely.
WARNING! Never engage the cruise control lever
while traveling in reverse.
WARNING! Do not mow on inclines with a slope in
excess of 15 degrees (a rise of approximately 2-1⁄2
feet every 10 feet). The tractor could overturn and
cause serious injury.
To set the cruise control:
1.
Slowly press the forward drive pedal with your right foot
until the desired speed is achieved.
•
•
Mow up and down slopes, NEVER across.
Exercise extreme caution when changing direction on
slopes.
2.
Lift the parking brake/cruise control lever upward and
hold it in that position.
•
•
•
Watch for holes, ruts, bumps, rocks, or other hidden
objects. Uneven terrain could overturn the machine. Tall
grass can hide obstacles.
3.
Remove your foot from the forward drive pedal
Release pressure from the parking brake/cruise control
lever
.
4.
Avoid turns when driving on a slope. If a turn must be
made, turn down the slope. Turning up a slope greatly
increases the chance of a roll over.
.
After completing step 3, the forward drive pedal should remain
in the down position and the tractor will maintain the same
forward speed. If it doesn’t, the cruise control is not engaged.
Repeat steps 1-4 to engage the cruise control.
Avoid stopping when driving up a slope. If it is necessary
to stop while driving up a slope, start up smoothly and
carefully to reduce the possibility of flipping the tractor
over backward.
To disengage the cruise control, lightly press the forward drive
Engaging the Parking Brake
pedal or the brake pedal
.
NOTE: The parking brake must be set if the operator leaves the
seat with the engine running or the engine will automatically
shut off.
NOTE: Cruise control can not be set at the tractor’s fastest
ground speed. If the operator should attempt to do so, the
tractor will automatically decelerate to the fastest optimal
mowing ground speed.
To set the parking brake:
1.
Press the brake pedal
foot and hold it in that position.
completely down with your left
To change the direction of travel from forward to reverse when
cruise control is engaged, press the brake pedal to disengage
the cruise control and bring the tractor to a complete stop. Then
slowly press the reverse drive pedal with the ball of your foot to
travel in reverse.
2.
Lift the parking brake/cruise control lever upward and
hold it in that position.
3.
Remove your foot from the brake pedal
Release pressure from the parking brake/cruise control
lever
.
Using the Lift Lever
4.
Manual Lift Lever (If so equipped)
To raise or lower the cutting deck, move the lift lever to the left,
then place it in the notch best suited for your application.
.
After completing step 3, the brake pedal should remain in the
down position. If it doesn’t, the parking brake is not engaged.
Repeat steps 1-4 to engage the parking brake.
Electric Lift Switch (If so equipped)
To disengage the parking brake, lightly press the brake pedal .
When operating the tractor’s electric lift switch, always complete
the following steps.
WARNING! Never leave a running machine
unattended. Always disengage PTO, set parking
brake, stop engine and remove key to prevent
unintended starting
1.
Press down on the rear of the lift switch to raise the deck all
the way into its highest position.
2.
Position the cutting height lever in the desired setting.
3.
Press down on the front of the lift switch to lower the deck
into the position set in the previous step.
NOTE: The deck will automatically stop lowering when
it reaches the point determined by the position of the
cutting height lever.
CAUTION: Failure to follow these instructions
when operating the tractor’s electric lift switch will
result in premature wear of the tractor’s electric lift
system.
Section 5 — operation
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating the Headlights
The lamps are ON whenever the ignition key is rotated out of the
STOP
position. The lamps turn OFF when the ignition key is
moved to the STOP
position.
Engaging the PTO
Engaging the PTO transfers power to the cutting deck or other
(separately available) attachments. To engage the PTO:
1.
Move the throttle control lever to the FAST
position.
2.
Pull the PTO/Blade Engage lever
position. See Figure 5-3.
upward into the ON
Figure 5-3
NOTE: When operating the tractor be certain that the
throttle lever is always in the FAST (rabbit) position.
Operating with the throttle at less than full throttle may
lead to premature battery wear and a poor quality cut.
Section 5 — operation
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance & Adjustments
6
Maintenance Schedule
Before
Every
Every
Every
Prior
Each use
10 Hours
25 Hours
200 Hours
to Storing
Check/Clean Engine Intake Screen
P
P
P
Clean Hood/Dash Louvers
P
P
Check Engine Oil Level
P
P
Check Transmission Oil
Change Transmission Oil & Filter *
Clean Battery Terminals
P
P
P
P
Lube Front Axles and Rims
Lube Pedal Pivot Points
P
P
* — For break-in operation, change after the first 50 hours of use and then every 200 hours thereafter.
NOTE: This Operator’s Manual covers several models. Tractor
features may vary by model. Not all features in this manual are
Engine
applicable to all tractor models and the tractor depicted may
differ from yours.
Refer to the Kohler Owner’s Manual for all engine maintenance
procedures and instructions.
WARNING! Before performing any maintenance or
repairs, disengage PTO, set parking brake, stop
engine and remove key to prevent unintended
starting.
Changing the Engine Oil
WARNING! If the engine has been recently run, the
engine, muffler and surrounding metal surfaces will
be hot and can cause burns to the skin. Exercise
caution to avoid burns.
Battery
To complete an oil change, proceed as follows:
CALIFORNIA PROPOSITION 65 WARNING!
Battery posts, terminals, and related accessories
contain lead and lead compounds, chemicals known
to the State of California to cause cancer and
reproductive harm. Wash hands after handling.
1.
Run the engine for a short time to warm the engine oil. The
oil will flow more freely and carry away more impurities.
Use care to avoid burns from hot oil.
2.
Locate the oil drain hose on the left side of the engine.
The battery is sealed and is maintenance-free. Acid levels cannot
be checked and fluid can not be added.
3.
Remove the hose from the retaining loop-clamp. Route
the free end of the oil drain hose toward an appropriate
oil collection container with at least a 2.5 quart capacity,
to collect the used oil. Remove the oil fill cap/dipstick from
the oil fill tube.
•
Always keep the battery cables and terminals clean and
free of corrosive build-up.
•
After cleaning the battery and terminals, apply a light coat
of petroleum jelly or grease to both terminals.
CAUTION: If removing the battery for cleaning,
disconnect the NEGATIVE (Black) wire from it’s terminal
first, followed by the POSITIVE (Red) wire. When re-
installing the battery, always connect the POSITIVE
(Red) wire its terminal first, followed by the NEGATIVE
(Black) wire. Be certain that the wires are connected to
the correct terminals; reversing them could result in
serious damage to your engine’s alternating system.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
4.
While holding the free end of the oil drain hose over the oil
collection container, unscrew the square head hose plug
from the end of the hose. See Figure 6-1. Drain the engine
oil into the collection container.
Hydrostatic Transmission Oil
Checking the Hydrostatic Transmission Oil
The dipstick to check the hydrostatic transmission oil level is
located on the back of the mower on the upper section of the
frame. Refer to the Controls & Features section of this manual.
1.
Remove the dipstick and check the level. See Figure 6-2.
Oil Drain Hose
F
Full
OK
A
Add
Square Head Plug
Figure 6-1
5.
After draining the oil, wipe any residual oil from the oil
drain hose. Thread the square head plug into the drain
hose fitting and fully tighten the plug.
Figure 6-2
6.
7.
Replace the oil filter, and refill the engine with new oil as
instructed in the Kohler Owner’s Manual.
2.
If the level is above the “ADD” level and in the “OK” range, it
is not necessary to add any transmission oil. If the level is at
or below the “ADD” level add transmission oil into the oil fill
port until the level is in the “OK” range. For best results, fill
to the “FULL” mark on the dipstick as opposed to adding a
specific volume of oil. Do NOT overfill.
Re-insert hose through the retaining loop-clamp.
To refill the oil, re-install the square head plug at the end of
the hose and refer to the Engine Operator’s Manual for refilling
instructions, oil type and amount.
NOTE: The approved fluid is Cub Cadet Drive System Fluid
Plus. (1 quart — Part No. 737-3120/1 gallon — 737-3121).
NOTE: Maintenance, repair, or replacement of the emission control
devices and systems which are being done at owner’s expense may
be performed by any engine repair establishment or individual.
Warranty repairs must be performed by a Cub Cadet Dealer.
3.
Reinstall the transmission oil fill plug/dipstick securely into
the oil fill port.
4.
Start the engine and allow it to run for a few minutes. Shut
the engine off, then check for leaks and re-check the oil
level in the transmission case.
Changing the Hydrostatic Transmission Oil
CAUTION: Never overfill the transmission case.
Damage or leakage may result if the oil level in the
transmission case is below the “ADD” mark or over
the “FULL” mark of the dipstick.
1.
Place the tractor on a level surface and engage the brake pedal
lock. Stop the tractor engine and remove the ignition key.
2.
Clean the area around the transmission drain plug to
prevent debris from entering the transmission case.
Section 6 — Maintenance & adjuStMentS
19
Download from Www.Somanuals.com. All Manuals Search And Download.
3.
Remove the drain plug and allow the transmission oil to
drain into a clean container having a capacity of more than
six quarts. Reinstall the drain plug. See Figure 6-3.
Cleaning the Tractor
Any fuel or oil spilled on the machine should be wiped off
promptly. Do NOT allow debris to accumulate around the cooling
fins of the engine, the transmission’s cooling fan or on any other
part of the machine.
Cleaning the Engine Intake Screen
The engine intake screen area is located on the lower half of the
dash. It is important to keep this area free of debris. Clean this
area prior to each use. See Figure 6-4.
Oil Filter
Oil Drain Plug
Figure 6-3
4.
5.
Clean around the base of the transmission oil filter and
remove the filter by turning it counterclockwise. Refer to
Figure 6-3.
Engine Intake Screen
Apply a light coating of clean transmission oil to the gasket
of the new filter. Install the filter by turning it clockwise,
by hand. When the gasket contacts the filter base on the
transmission housing, tighten the filter an additional 1⁄2-turn.
Figure 6-4
6.
7.
Clean the area around the transmission oil fill plug/dipstick
to prevent debris from entering the transmission case.
Lubrication
Remove the oil fill plug/dipstick from the oil fill port and
SLOWLY pour oil into the oil fill port. Fill the transmission
case until the oil level reaches the “FULL” mark on the
dipstick Refer to Figure 6-2.
WARNING! Before lubricating, repairing, or
inspecting, always disengage PTO, set parking
brake, stop engine and remove key to prevent
unintended starting.
NOTE: The transmission has a capacity of approximately
5-1⁄2 quarts.
8.
9.
Reinstall the oil fill plug/dipstick securely into the oil fill
port.
Start the engine and allow it to run for a few minutes. Shut
the engine off, then check for leaks and re-check the oil
level in the transmission case.
CAUTION: The transmission oil fill plug/dipstick
must be installed securely into the fill port at all
times when the engine is operating.
Hydrostatic Neutral Adjustment
If the tractor creeps forward or rearward when neither the
forward nor reverse pedal is depressed, contact your local
Cub Cadet dealer to have the hydrostatic control rods properly
adjusted.
Section 6 — Maintenance & adjuStMentS
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Steering Housing & Steering Shaft
Parking Brake Adjustment
The steering housing and steering shaft should be lubricated
after every 25 hour of operation. To access the lube fittings,
proceed as follows:
If the tractor does not come to a complete stop when the brake
pedal is completely depressed, or if the tractor’s rear wheels can
roll with the parking brake applied (and the hydrostatic relief
valve open), the brake is in need of adjustment. See your Cub
Cadet dealer to have the brake adjusted.
1.
Raise the tractor’s hood.
2.
Locate the grease fitting for the steering housing and
steering shaft under the battery. See Figure 6-5.
Wheel Alignment
The front wheels should toe-in approximately 1⁄8 to 1⁄4”, as
measured across dimensions A and B. See Figure 6-6.
Steering Gear
Centered
Pivot Hole
Centering Hole
A
C
C
Grease Fittings
D
D
B
Figure 6-5
3.
Using a pressure lubricating gun, apply 251H EP grease, or
an equivalent No. 2 multipurpose lithium grease, through
the grease fittings.
Figure 6-6
Steering/Toe-in Adjustment
To adjust front wheel toe-in, proceed as follows:
4.
Close the tractor hood
Deck Wheels
1.
Check the steering gear to ensure it is in the centered
position. The hole in the steering segment gear will align
with the hole in the steering housing (See Figure 6-6).
Each of the tractor deck’s gauge wheels is equipped with a grease
fitting. Lubricate with a No. 2 multi-purpose grease applied with a
grease gun after every 25 hours of tractor operation.
NOTE: A 5⁄16” pin can be used in the alignment holes to
assure the steering segment is centered.
Pivot Points & Linkage
2.
3.
4.
Mark the front horizontal diameter of both front wheels at
the same spot on each wheel-preferably the inner bead
flange of the wheel rims. Mark the rear horizontal diameter
of both front wheels in the same manner.
Lubricate all the pivot points on the drive system, parking brake
and lift linkage at least once a season with light oil.
Adjustments
Measure the distance between the bottom edges of the
tractor frame channels and the marks on the front of each
wheel (See measurement D in Figure 6-6). These two
measurements should be equal.
WARNING! Shut the engine off, remove the
ignition key and engage the parking brake before
making adjustments. Protect your hands by using
heavy gloves when handling the blades.
Measure the distance between the frame and the marks on
the rear of each front wheel (See measurement C in Figure
6-6). Measurement D should be approximately 1⁄16- to 1⁄8-
inch less than measurement C on each side of the tractor.
NOTE: Check the tractor’s tire pressure before performing
any deck leveling adjustments. Refer to Tires on page 10 for
information regarding tire pressure.
Seat Adjustment
Refer to the Assembly & Set-Up section of this manual for seat
adjustment instructions.
WARNING! Before operating the tractor, make
sure the seat is engaged in the seat-stop. Engage the
parking brake. Stand behind the machine and pull
back on seat until it clicks into place.
Section 6 — Maintenance & adjuStMentS
21
Download from Www.Somanuals.com. All Manuals Search And Download.
5.
Loosen the jam nuts from the ball joints. See Figure 6-7.
Pivot Bar Adjustment
CAUTION: The tractor should be checked every 50
hours of operation for play between the frame
channel and the pivot bar.
Check and adjust the pivot axle as follows:
Hex Lock Nut
Ball Joint
1.
Raise the front of the tractor and set it on jack stands, so
the front wheels are suspended above the ground.
WARNING! When jacking up the front end of the
tractor, always chock the rear wheels to prevent the
tractor from rolling, tipping or sliding off the jack
stands.
Steering Arm
Jam Nut
2.
Move the ends of the pivot bar up and down to check for
binding. If binding is present, loosen the lock nuts until
binding is eliminated. See Figure 6-8.
Drag Link
Adjustment Bolts
Figure 6-7
6.
Disconnect the front ball joints from the steering arms by
removing the hex lock nuts. Refer to Figure 6-7. Manually
move each wheel to achieve the required toe-in and equal
D measurements.
7.
Making sure not to move the steering gear or either wheel,
turn the ball joint in or out on each drag linkas necessary to
align with the hole in each steering arm.
Frame Channel
Lock Nuts
8.
Reinstall the ball joints in the steering arms and secure with
the hex lock nuts. Tighten the jam nuts against the ball
joints.
Pivot Bar
Figure 6-8
3.
Grasping the ends of the pivot bar, attempt to move each
end of the axle forward and rearward to check for side play
between the pivot bar and frame channel. If play is present,
gradually tighten the lock nuts until play is minimized.
4.
5.
Repeat steps 2 and 3 until minimum play without binding
is achieved.
Raise the front of the tractor, remove jack stands, and lower the
tractor to the ground. Remove the blocks from the rear wheels.
22
Section 6 — Maintenance & adjuStMentS
Download from Www.Somanuals.com. All Manuals Search And Download.
Lift Handle Adjustment (If so equipped)
The effort required to operate the implement lift handle can be
varied by loosening or tightening the lift assist spring adjusting
bolt on the left side of the tractor. See Figure 6-9.
Increase effort
Decrease effort
Adjustment Bolt
Figure 6-9
NOTE: The deck and/or attachment should be installed before
making adjustments to this spring.
Place the deck/attachment into the lowest position for making
adjustments. This ensures that the spring is extended the furthest.
The bolt can be accessed from the rear of the tractor, inside the left
rear wheel. Turning adjusting bolt clockwise will decrease the manual
effort required for lifting attachments; turning counterclockwise will
increase the effort needed to lift the attachment.
NOTE: Overtightening of the spring could cause the deck to
float and/or fail out of the notches. There should always be a
downward/forward bias on the lever for proper operation.
Section 6 — Maintenance & adjuStMentS
Download from Www.Somanuals.com. All Manuals Search And Download.
23
Service
7
3.
4.
5.
Note which battery tray hole the RH side of the hold-down
rod is hooked into.
Battery
Common Causes For Battery Failure
Rotate the hold-down rod upward, over and around the
battery to unhook from the battery tray.
1.
2.
3.
4.
5.
Overcharging
Lift the battery out off the battery tray and remove from
the tractor.
Undercharging
Loose and/or corroded connections
Excessive loads
6.
7.
Position the new battery and lower into the battery tray.
Hook the hold-down rod into the previously noted battery
tray hole, then rotate the rod around and over the battery.
Freezing of electrolyte
* These causes do not constitute warranty in the event of a
battery failure.
8.
9.
Align the LH side of the hold-down rod with the hole in the
battery tray and secure with hex screw remove earlier.
Battery Removal or Installation
Connect the positive cable to the positive terminal of the
battery, then connect the negative cable to the negative
terminal.
WARNING! Battery posts, terminals and related
accessories contain lead and lead compounds. Wash
Hands after handling.
Charging The Battery
Test and, if necessary, recharge the battery after the tractor has
been stored for a period of time.
When removing the battery, disconnect the battery cables in the
following order to avoid arcing and the resulting sparks:
•
A voltmeter or load tester should read 12.6 volts (DC) or
higher across the battery terminals. See Figure 7-2.
Battery Removal
1.
Disconnect the Negative cable.
Disconnect the Positive cable.
2.
Voltmeter
State of Charge Charging Time
Reading
When installing the battery, connect the battery cables in the
following order:
12.7
12.4
12.2
12.0
100%
75%
50%
25%
Full Charge
90 Min.
Battery Installation
1.
Connect the Positive cable.
Connect the Negative cable.
180 Min.
280 Min.
2.
To replace the battery, proceed as follows:
Figure 7-2
1.
Remove the negative cable from the negative terminal of the
battery, then remove positive cable from the positive terminal.
•
Charge the battery with a 12-volt battery charger at a
MAXIMUM rate of 10 amps.
2.
Remove the hex screw securing the LH side of the hold
down rod to the battery tray. See Figure 7-1.
Hold Down Rod
Rotate
Upward
Hex
Screw
Battery Tray
Figure 7-1
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Headlights
Refer to Replacement Parts section when replacement of head
lamp bulbs is necessary.
Replace headlight bulbs as follows:
1.
Fully raise the hood of the tractor.
2.
Unplug the wire harness leads from the headlight socket
terminals. Note which wire connects to each terminal
before disconnecting.
3.
Rotate the socket assembly approximately 1⁄4 turn to align
the socket tab with the reflector housing notch; then
withdraw the bulb and socket assembly from the reflector
housing. See Figure 7-3.
Terminal
Socket Tab
Socket
Reflector Housing
Reflector Notch
Figure 7-3
4.
5.
Push the bulb inward and turn counterclockwise to remove
from the socket.
Align a locking post of the bulb base with the notch in the
socket, then push the bulb inward and turn clockwise to
lock. See Figure 7-3.
6.
7.
Align the socket tab with the notch of the reflector
housing; then push the socket inward and turn as
necessary to lock the socket in the housing:
Connect the wire harness leads to the appropriate socket
terminals.
Fuses
Always use the same capacity fuse for replacement. If the
electrical system does not function, check the fuses.
To replace a fuse, pull the old fuse from the fuse holder and
install the new fuse.
Section 7 — Service
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
8
Problem
Cause
Remedy
1. Tighten blade and spindle.
Excessive vibration
1. Cutting blade loose or unbalanced.
2. Damaged or bent cutting blade.
2. Replace blade.
Mower will not mulch grass
(If equipped)
1. Engine speed too low.
1. Place throttle in FAST (rabbit) position.
2. Wet grass.
2. Do not mulch when grass is wet.
3. Excessively high grass.
3. Mow once at a high cutting height, then
mow again at desired height or make a
narrower cutting swath.
4. Dull blade.
4. Sharpen or replace blade.
Uneven cut
1. Deck not leveled properly.
1. Perform side-to-side deck adjustment.
2. Dull blade.
2. Sharpen or replace blade.
3. Uneven tire pressure.
3. Check tire pressure in all four tires.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacement Parts
9
Component
Part Number and Description
925-1707D
Battery
951-12725
Fuel Cap
946-04759A
Choke Control Cable
946-04771A
Throttle Control Cable
925-2054A
Ignition Key
925-0963
12V Bulb
Phone (800) 965-4CUB to order replacement parts or a complete Parts Manual (have your full model number and serial number
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Attachments & Accessories
10
GTX2100
GT2000 & GTX2000
The following attachments and accessories are compatible for
Cub Cadet GTX2100. See your Cub Cadet dealer or the retailer
The following attachments and accessories are compatible for
Cub Cadet GT2000. See your Cub Cadet dealer or the retailer
from which you purchased your tractor for information regarding from which you purchased your tractor for information regarding
price and availability.
price and availability.
Model Number
Description
Model Number
Description
19A40012100
19A40015100
19A40013100
19A40016100
19A40014100
19A40022100
19A40019100
19A40022100
19A40021100
19A70016100
190-193-000
19A70023100
590-507-100
19A40003100
19A40004100
190-307-100
490-241-0026
490-850-0008
490-850-0005
42” Staggered Deck
48” Fabricated Deck
50” Stamped Deck
54” Fabricated Deck
54” Stamped Deck
46” Snow Blade
19A40012100
19A40013100
19A40014100
19A40022100
19A40019100
19A40022100
19A40021100
19A70016100
190-193-000
19A70023100
590-507-100
19A40003100
19A40004100
190-307-100
490-241-0026
490-850-0008
490-850-0005
42” Staggered Deck
50” Stamped Deck
54” Stamped Deck
46” Snow Blade
44” Snow Thrower
46” Snow Thrower
42” Mulch Kit
44” Snow Thrower
46” Snow Thrower
42” Mulch Kit
48” Fabricated Mulch Kit
50” Mulch Kit
48” Fabricated Mulch Kit
50” Mulch Kit
54” Fabricated Mulch Kit
54” Stamped Mulch Kit
Twin Bagger
54” Fabricated Mulch Kit
54” Stamped Mulch Kit
Twin Bagger
Triple Bagger
Weight Kits
Tire Chains
Triple Bagger
Oil Siphon
Weight Kits
Blade Removal Tool
Tire Chains
Oil Siphon
Blade Removal Tool
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
11
29
Download from Www.Somanuals.com. All Manuals Search And Download.
FEDERAL and/or CALIFORNIA EMISSION CONTROL WARRANTY STATEMENT
YOUR WARRANTY RIGHTS AND OBLIGATIONS
MTD Consumer Group Inc, the United States Environmental Protection Agency (EPA), and, for those products certified for sale in the state of
California, the California Air Resources Board (CARB) are pleased to explain the emission (evaporative and/or exhaust) control system (ECS)
warranty on your outdoor 2006 and later small off-road spark-ignited engine and equipment (outdoor equipment engine) In California, new
outdoor equipment engines must be designed, built and equipped to meet the State’s stringent anti-smog standards (in other states, 1997 and
later model year equipment must be designed, built, and equipped to meet the U.S. EPA small off-road, spark ignition engine regulations. MTD
Consumer Group Inc must warrant the ECS on your outdoor equipment engine for the period of time listed below provided there has been no
abuse, neglect or improper maintenance of outdoor equipment engine.
Your ECS may include parts such as the carburetor, fuel-injection system, the ignition system, catalytic converter, fuel tanks, fuel lines, fuel caps,
valves, canisters, filters, vapor hoses, clamps, connectors, and other associated emission-related components.
Where a warrantable condition exists, MTD Consumer Group Inc will repair your outdoor equipment engine at no cost to you including
diagnosis, parts and labor.
MANUFACTURER’S WARRANTY COVERAGE:
This emission control system is warranted for two years. If any emission-related part on your outdoor equipment engine is defective, the part
will be repaired or replaced by MTD CONSUMER GROUP INC.
OWNER’S WARRANTY RESPONSIBILITIES:
As the outdoor equipment engine owner, you are responsible for performance of the required maintenance listed in your owner’s manual. MTD
Consumer Group Inc recommends that you retain all receipts covering maintenance on your outdoor equipment engine, but MTD Consumer
Group Inc cannot deny warranty solely for the lack of receipts.
As the outdoor equipment engine owner, you should however be aware that MTD Consumer Group Inc may deny you warranty coverage if
your outdoor equipment engine or a part has failed due to abuse, neglect, or improper maintenance or unapproved modifications.
You are responsible for presenting your outdoor equipment engine to MTD Consumer Group Inc’s distribution center or service center as soon
as the problem exists. The warranty repairs should be completed in a reasonable amount of time, not to exceed 30 days. If you have a question
regarding your warranty coverage, you should contact the MTD Consumer Group Inc Service Department at 1-800-800-7310 or via email at
GENERAL EMISSIONS WARRANTY COVERAGE:
MTD Consumer Group Inc warrants to the ultimate purchaser and each subsequent purchaser that the outdoor equipment engine is: Designed,
built and equipped so as to conform with all applicable regulations; and free from defects in materials and workmanship that cause the failure
of a warranted part to be identical in all material respects to that part as described in MTD Consumer Group Inc’s application for certification.
The warranty period begins on the date the outdoor equipment engine is delivered to an ultimate purchaser or first placed into service. The
warranty period is two years.
Subject to certain conditions and exclusions as stated below, the warranty on emission-related parts is as follows:
1.
Any warranted part that is not scheduled for replacement as required maintenance in the written instructions supplied, is warranted for
the warranty period stated above. If the part fails during the period of warranty coverage, the part will be repaired or replaced by MTD
Consumer Group Inc according to subsection (4) below. Any such part repaired or replaced under warranty will be warranted for the
remainder of the period.
2.
Any warranted part that is scheduled only for regular inspection in the written instructions supplied is warranted for the warranty period
stated above. Any such part repaired or replaced under warranty will be warranted for the remaining warranty period.
3.
Any warranted part that is scheduled for replacement as required maintenance in the written instructions supplied is warranted for the
period of time before the first scheduled replacement date for that part. If the part fails before the first scheduled replacement, the part
will be repaired or replaced by MTD Consumer Group Inc according to subsection (4) below. Any such part repaired or replaced under
warranty will be warranted for the remainder of the period prior to the first scheduled replacement point for the part.
4.
5.
6.
7.
Repair or replacement of any warranted part under the warranty provisions herein must be performed at a warranty station at no charge
to the owner.
Notwithstanding the provisions herein, warranty services or repairs will be provided at all of our distribution centers that are franchised to
service the subject engines or equipment.
The outdoor equipment engine owner will not be charged for diagnostic labor that is directly associated with diagnosis of a defective,
emission-related warranted part, provided that such diagnostic work is performed at a warranty station.
MTD Consumer Group Inc is liable for damages to other engine or equipment components proximately caused by a failure under
warranty of any warranted part.
8.
9.
Throughout the off-road engine and equipment warranty period stated above, MTD Consumer Group Inc will maintain a supply of
warranted parts sufficient to meet the expected demand for such parts.
Any replacement part may be used in the performance of any warranty maintenance or repairs and must be provided without charge to
the owner. Such use will not reduce the warranty obligations of MTD Consumer Group Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
10. Add-on or modified parts that are not exempted by the Air Resources Board may not be used. The use of any non-exempted add-on or
modified parts by the ultimate purchaser will be grounds for disallowing a warranty claims. MTD Consumer Group Inc will not be liable to
warrant failures of warranted parts caused by the use of a non-exempted add-on or modified part.
WARRANTED PARTS:
The repair or replacement of any warranted part otherwise eligible for warranty coverage may be excluded from such warranty coverage if
MTD Consumer Group Inc demonstrates that the outdoor equipment engine has been abused, neglected, or improperly maintained, and that
such abuse, neglect, or improper maintenance was the direct cause of the need for repair or replacement of the part. That notwithstanding,
any adjustment of a component that has a factory installed, and properly operating, adjustment limiting device is still eligible for warranty
coverage. Further, the coverage under this warranty extends only to parts that were present on the off-road engine and equipment purchased.
The following emission warranty parts are covered (if applicable):
1.
Fuel Metering System
•
•
•
•
Cold start enrichment system (soft choke)
Carburetor and internal parts (or fuel injection system)
Fuel pump
Fuel tank
2.
3.
4.
5.
6.
Air Induction System
•
•
Air cleaner
Intake manifold
Ignition System
•
•
Spark plug(s)
Magneto ignition system
Exhaust System
•
•
Catalytic converter
SAI (Reed valve)
Miscellaneous Items Used in Above System
•
•
Vacuum, temperature, position, time sensitive valves and switches
Connectors and assemblies
Evaporative Control
•
•
•
•
•
Fuel hose
Fuel hose clamps
Tethered fuel cap
Carbon canister
Vapor lines
GDOC-100223 Rev. A
Download from Www.Somanuals.com. All Manuals Search And Download.
CUB CADET LLC
MANUFACTURER’S LIMITED WARRANTY FOR
SERIES 2000 TRACTORS
IMPORTANT: To obtain warranty coverage owner must present an
In the U.S.A.
original proof of purchase and applicable maintenance records to the
servicing dealer. Please see the operator’s manual for information on
required maintenance and service intervals.
Check your Yellow Pages, or contact Cub Cadet LLC at P.O. Box 361131,
Cleveland, Ohio 44136-0019, call 1-877-282- 8684
The limited warranty set forth below is given by Cub Cadet LLC with
respect to new merchandise purchased or leased and used in the
United States and/or its territories and possessions, and by MTD
Products Limited with respect to new merchandise purchased or
leased and used in Canada and/or its territories and possessions
(either entity respectively, “Cub Cadet”).
In Canada
Contact MTD Products Limited, Kitchener, ON N2G 4J1, call 1-800-
Without limiting the foregoing, this limited warranty does not
provide coverage in the following cases:
a.
Routine maintenance items such as lubricants, filters, blade
sharpening, tune-ups, brake adjustments, clutch adjustments,
deck adjustments, and normal deterioration of the exterior
finish due to use or exposure.
Cub Cadet warrants this product (excluding its Normal Wear Parts,
Batteries, Frame, Front Axle and Drive Shaft and Attachments as
described below) against defects in material and workmanship for
a period of four (4) years or three hundred (300) operation hours,
whichever comes first, commencing on the date of original retail
purchase or lease and will, at its option, repair or replace, free of
charge, any part found to be defective in materials or workmanship.
b.
c.
Service completed by someone other than an authorized
service dealer.
Cub Cadet does not extend any warranty for products sold
or exported outside of the United States and/or Canada, and
their respective possessions and territories, except those sold
through Cub Cadet’s authorized channels of export distribution.
Normal Wear Parts are warranted to be free from defects in material
and workmanship for a period of thirty (30) days from the date of
original purchase or lease. Normal wear parts include, but are not
limited to items such as: belts, blades, blade adapters, grass bags,
rider deck wheels, seats, and tires.
d.
e.
Replacement parts and\or accessories that are not genuine Cub
Cadet parts.
Batteries have a one-year prorated limited warranty against defects
in material and workmanship, with 100% replacement during the
first three months. After three months, the battery replacement
credit is based on the months remaining in the twelve (12) month
period dating back to the original date of original sale or lease. Any
replacement battery will be warranted only for the remainder of the
original warranty period.
Transportation charges and service calls.
There are no implied warranties, including without limitation
any implied warranty of merchantability or fitness for a
particular purpose. No warranties shall apply after the applicable
period of express written warranty above. No other express
warranties beyond those mentioned above, given by any person
or entity, including a dealer or retailer, with respect to any
product, shall bind Cub Cadet. The exclusive remedy is repair or
replacement of the product as set forth above. The terms of this
warranty provide the sole and exclusive remedy arising from the
sale and/or lease of the products covered hereby. Cub Cadet shall
not be liable for any incidental or consequential loss or damage
including, without limitation, expenses incurred for substitute
or replacement lawn care services or for rental expenses to
temporarily replace a warranted product.
Frame, Front Axle and Drive Shaft — Cub Cadet warrants the frame,
front cast iron pivot axle and drive shaft against defects in material
and workmanship for a period of five (5) years or 500 hours, whichever
occurs first, commencing on the date of original purchase or lease.
Attachments — Cub Cadet warrants attachments for this product
against defects in material and workmanship for a period of two (2)
years, commencing on the date of the attachment’s original purchase
or lease. Attachments include, but are not limited to items such as:
grass collectors and mulch kits.
Some jurisdictions do not allow the exclusion or limitation of
incidental or consequential damages, or limitations on how long an
implied warranty lasts, so the above exclusions or limitations may not
apply to you.
This limited warranty shall only apply if this product has been
operated and maintained in accordance with the Operator’s
Manual furnished with the product, and has not been subject to
misuse, abuse, neglect, accident, improper maintenance, alteration,
vandalism, theft, fire, water, or damage because of other peril or
natural disaster. Damage resulting from the installation or use of any
part, accessory or attachment not approved by Cub Cadet for use
with the product(s) covered by this manual will void your warranty as
to any resulting damage. In addition, Cub Cadet may deny warranty
coverage if the hour meter, or any part thereof, is altered, modified,
disconnected or otherwise tampered with.
In no event shall recovery of any kind be greater than the amount of
the purchase price of the product sold. Alteration of safety features
of the product shall void this warranty. You assume the risk and
liability for loss, damage, or injury to you and your property and/or to
others and their property arising out of the misuse or inability to use
the product.
This limited warranty shall not extend to anyone other than the
original purchaser or to the person for whom it was purchased as a
gift.
HOW TO OBTAIN SERVICE: Warranty service is available, WITH
PROOF OF PURCHASE AND APPLICABLE MAINTENANCE RECORDS,
through your local authorized service dealer. To locate the dealer in
your area:
HOW LOCAL LAWS RELATE TO THIS WARRANTY: This limited
warranty gives you specific legal rights, and you may also have other
rights that vary in different jurisdictions.
Cub Cadet LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019, Phone: 1-877-282-8684
MTD Products Limited, Kitchener, ON N2G 4J1, Phone: 1-800-668-1238
GDOC-100259 REV. A
Download from Www.Somanuals.com. All Manuals Search And Download.
|