Cub Cadet Lawn Mower 190 670 100 190 678 100 User Manual

Operator’s Manual  
Twin Rear Bagger Kit  
Models  
190-670-100  
and  
190-678-100  
IMPORTANT: Read safety rules and instructions carefully  
Warning: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest-covered,  
brush-covered or grass-covered land unless the engine’s exhaust system is equipped with a spark arrester meeting applicable local or state  
laws (if any). If a spark arrester is used, it should be maintained in effective working order by the operator. In the State of California the  
above is required by law (Section 4442 of the California Public Resources Code). Other states may have similar laws. Federal laws apply  
on federal lands. A spark arrester for the muffler is available through your Cub Cadet dealer or contact the service department, P.O. Box  
361131 Cleveland, Ohio 44136-0019.  
Cub Cadet LLC., P.O. Box 361131, Cleveland, Ohio 44136-0019  
PRINTED IN U.S.A.  
769-00657  
(1/2003)  
FORM NO.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SECTION 1: IMPORTANT SAFE OPERATION PRACTICES  
WARNING: This symbol points out important safety instructions which, if not followed, could endanger  
the personal safety and/or property of yourself and others. Read and follow all instructions in this manual  
before attempting to operate this machine. Failure to comply with these instructions may result in personal  
injury. When you see this symbolheed its warning.  
WARNING: The Battery and Engine Exhaust contains chemicals known to the State of California  
to cause cancer, birth defects or other reproductive harm. The battery and posts contain lead;  
wash hands after handling  
.
WARNING: This machine was built to be operated according to the rules for safe operation in this  
manual. As with any type of power equipment, carelessness or error on the part of the operator can result in  
serious injury. This machine is capable of amputating hands and feet and throwing objects. Failure to  
observe the following safety instructions could result in serious injury or death.  
12. A missing or damaged discharge cover can cause blade  
General Operation  
contact or thrown object injuries.  
13. Stop the blade(s) when crossing gravel drives, walks, or  
roads and while not cutting grass.  
14. Watch for traffic when operating near or crossing  
roadways. This machine is not intended for use on any  
public roadway.  
15. Do not operate the machine while under the influence of  
alcohol or drugs.  
16. Mow only in daylight or good artificial light.  
17. Never carry passengers.  
18. Disengage blade(s) before shifting into reverse. Back up  
slowly. Always look down and behind before and while  
backing to avoid a back-over accident.  
19. Slow down before turning. Operate the machine  
smoothly. Avoid erratic operation and excessive speed.  
20. Disengage blade(s), set parking brake, stop engine and  
wait until the blade(s) come to a complete stop before  
removing grass catcher, emptying grass, unclogging  
chute, removing any grass or debris, or making any  
adjustments.  
21. Never leave a running machine unattended. Always turn  
off blade(s), place transmission in neutral, set parking  
brake, stop engine and remove key before dismounting.  
22. Use extra care when loading or unloading the machine  
into a trailer or truck. This unit should not be driven up or  
down ramp(s), because the unit could tip over, causing  
serious personal injury. The unit must be pushed  
manually on ramp(s) to load or unload properly.  
23. Muffler and engine become hot and can cause a burn. Do  
not touch.  
24. Check overhead clearances carefully before driving  
under low tree branches, wires, door openings etc.,  
where the operator may be struck or pulled from the unit,  
which could result in serious injury.  
25. Disengage all attachment clutches, depress the brake  
pedal completely and shift into neutral before attempting  
to start engine.  
1. Read, understand, and follow all instructions on the  
machine and in the manual(s) before attempting to  
assemble and operate. Keep this manual in a safe place  
for future and regular reference and for ordering  
replacement parts.  
2. Be familiar with all controls and their proper operation.  
Know how to stop tractor and disengage controls quickly.  
3. Never allow children under 14 years old to operate this  
machine. Children 14 years old and over should read and  
understand the operation instructions and safety rules in  
this manual and should be trained and supervised by a  
parent.  
4. Never allow adults to operate this machine without proper  
instruction.  
5. To help avoid blade contact or a thrown object injury,  
keep bystanders, helpers, children and pets at least 75  
feet from the machine while it is in operation. Stop  
machine if anyone enters the area.  
6. Thoroughly inspect the area where the equipment is to be  
used. Remove all stones, sticks, wire, bones, toys, and  
other foreign objects which could be picked up and  
thrown by the blade(s). Thrown objects can cause  
serious personal injury.  
7. Plan your mowing pattern to avoid discharge of material  
toward roads, sidewalks, bystanders and the like. Also,  
avoid discharging material against a wall or obstruction  
which may cause discharged material to ricochet back  
toward the operator.  
8. Always wear safety glasses or safety goggles during  
operation and while performing an adjustment or repair to  
protect your eyes. Thrown objects which ricochet can  
cause serious injury to the eyes.  
9. Wear sturdy, rough-soled work shoes and close-fitting  
slacks and shirts. Loose fitting clothes and jewelry can be  
caught in movable parts. Never operate this machine in  
bare feet or sandals.  
10. Be aware of the mower and attachment discharge  
direction and do not point it at anyone. Do not operate the  
mower without the discharge cover or entire grass  
catcher in its proper place.  
11. Do not put hands or feet near rotating parts or under the  
cutting deck. Contact with the blade(s) can amputate  
hands and feet.  
26. Your machine is designed to cut normal residential grass  
of a height no more than 10. Do not attempt to mow  
through unusually tall, dry grass (e.g., pasture) or piles of  
dry leaves. Dry grass or leaves may contact the engine  
exhaust and/or build up on the mower deck presenting a  
potential fire hazard.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
27. Use only accessories and attachments approved for this  
machine by the machine manufacturer. Read,  
understand and follow all instructions provided with the  
accessory or attachment.  
28. Data indicates that operators, age 60 years and above,  
are involved in a large percentage of tractor-related  
injuries. These operators should evaluate their ability to  
operate the tractor safely enough to protect themselves  
and others from serious injury.  
dump cart, lawn roller, etc.) on slopes greater than 5  
degrees. When going down hill, the extra weight tends to  
push the tractor and may cause you to loose control. (e.g.  
tractor may speed up, braking and steering ability are  
reduced, attachment may jack-knife and cause tractor to  
overturn).  
Children  
1. Tragic accidents can occur if the operator is not alert to  
the presence of children. Children are often attracted to  
the machine and the mowing activity. They do not  
understand the dangers. Never assume that children will  
remain where you last saw them.  
29. If situations occur which are not covered in this manual,  
use care and good judgment. Contact your Yard-Man  
dealer for assistance.  
Slope Operation  
a. Keep children out of the mowing area and in  
watchful care of a responsible adult other than the  
operator.  
b. Be alert and turn machine off if a child enters the  
area.  
Slopes are a major factor related to loss of control and tip-  
over accidents which can result in severe injury or death. All  
slopes require extra caution. If you cannot back up the slope  
or if you feel uneasy, do not mow it.  
c. Before and while backing, look behind and down  
for small children.  
d. Never carry children, even with the blade(s) shut  
off. They may fall off and be seriously injured or  
interfere with safe machine operation.  
For your safety, use the slope gauge included as part of this  
manual to measure slopes before operating this unit on a  
sloped or hilly area. If the slope is greater than 15 degrees as  
shown on the slope gauge, do not operate this unit on that  
area.  
e. Use extreme care when approaching blind  
corners, doorways, shrubs, trees or other objects  
that may block your vision of a child who may run  
into the machine.  
f. Disengage the cutting blade(s) before shifting in  
reverse. The No-Cut-In Reversefeature  
emphasises not to cut in reverse and to avoid  
back-over accidents; do not defeat it.  
g. Keep children away from hot or running engines.  
They can suffer burns from a hot muffler.  
h. Remove key when machine is unattended to  
prevent unauthorized operation.  
Do:  
1. Mow up and down slopes, not across. Exercise extreme  
caution when changing direction on slopes.  
2. Watch for holes, ruts, bumps, rocks, or other hidden  
objects. Uneven terrain could overturn the machine. Tall  
grass can hide obstacles.  
3. Use slow speed. Choose a low enough speed setting so  
that you will not have to stop or shift while on the slope.  
Tires may lose traction on slopes even though the brakes  
are functioning properly. Always keep machine in gear  
when going down slopes to take advantage of engine  
braking action.  
4. Follow the manufacturers recommendations for wheel  
weights or counterweights to improve stability of the  
machine. Use extra care with grass catchers or other  
attachments. These can change stability of the machine.  
5. Keep all movement on the slopes slow and gradual. Do  
not make sudden changes in speed or direction. Rapid  
engagement or braking could cause the front of the  
machine to lift and rapidly flip over backwards which  
could cause serious injury.  
9. Never allow children under 14 years old to operate the  
machine. Children 14 years old and over should read and  
understand the operation instructions and safety rules in  
this manual and should be trained and supervised by a  
parent.  
Towing  
1. Tow only with a machine that has a hitch designed for  
towing. Do not attach towed equipment except at the  
hitch point.  
2. Follow the manufacturers recommendation for weight  
limits for towed equipment and towing on slopes.  
3. Never allow children or others in or on towed equipment.  
4. On slopes, the weight of the towed equipment may cause  
loss of traction and loss of control.  
6. Avoid starting or stopping on a slope. If tires lose traction,  
disengage the blade(s) and proceed slowly straight down  
the slope.  
Do Not:  
1. Do not turn on slopes unless necessary; then, turn slowly  
and gradually downhill, if possible.  
5. Travel slowly and allow extra distance to stop.  
6. Do not shift to neutral and coast downhill.  
2. Do not mow near drop-offs, ditches or embankments.  
The mower could suddenly turn over if a wheel is over the  
edge of a cliff, ditch, or if an edge caves in.  
3. Do not try to stabilize the machine by putting your foot on  
the ground.  
4. Do not use a grass catcher on steep slopes.  
5. Do not mow on wet grass. Reduced traction could cause  
sliding.  
Service  
Safe Handling Of Gasoline  
1. To avoid personal injury or property damage use extreme  
care in handling gasoline. Gasoline is extremely  
flammable and the vapors are explosive. Serious  
personal injury can occur when gasoline is spilled on  
yourself or your clothes which can ignite. Wash your skin  
and change clothes immediately.  
6. Do not shift to neutral and coast downhill. Over-speeding  
may cause the operator to lose control of the machine  
resulting in serious injury or death.  
a. Use only an approved gasoline container.  
b. Never fill containers inside a vehicle or on a truck  
7. Do not tow heavy pull behind attachments (e.g. loaded  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
or trailer bed with a plastic liner. Always place  
containers on the ground away from your vehicle  
before filling.  
complete stop within approximately (5) five seconds after  
operating the blade disengagement control. If the blades  
do not stop within the this time frame, your unit should be  
serviced professionally by an authorized dealer.  
4. Check brake operation frequently as it is subjected to  
wear during normal operation. Adjust and service as  
required.  
5. Check the blade(s) and engine mounting bolts at  
frequent intervals for proper tightness. Also, visually  
inspect blade(s) for damage (e.g., excessive wear, bent,  
cracked).  
c. When practical, remove gas-powered equipment  
from the truck or trailer and refuel it on the ground.  
If this is not possible, then refuel such equipment  
on a trailer with a portable container, rather than  
from a gasoline dispenser nozzle.  
d. Keep the nozzle in contact with the rim of the fuel  
tank or container opening at all times until fueling  
is complete. Do not use a nozzle lock-open  
device.  
e. Extinguish all cigarettes, cigars, pipes and other  
sources of ignition.  
f. Never fuel machine indoors.  
g. Never remove gas cap or add fuel while the  
engine is hot or running. Allow engine to cool at  
least two minutes before refueling.  
Replace the blade(s) with the original equipment  
manufacturers (O.E.M.) blade(s) only, listed in this  
manual. Use of parts which do not meet the original  
equipment specifications may lead to improper  
performance and compromise safety!”  
6. Mower blades are sharp. Wrap the blade or wear gloves,  
and use extra caution when servicing them.  
h. Never over fill fuel tank. Fill tank to no more than  
½ inch below bottom of filler neck to allow space  
for fuel expansion.  
i. Replace gasoline cap and tighten securely.  
j. If gasoline is spilled, wipe it off the engine and  
equipment. Move unit to another area. Wait 5  
minutes before starting the engine.  
k. To reduce fire hazards, keep machine free of  
grass, leaves, or other debris build-up. Clean up  
oil or fuel spillage and remove any fuel soaked  
debris.  
l. Never store the machine or fuel container inside  
where there is an open flame, spark or pilot light  
as on a water heater, space heater, furnace,  
clothes dryer or other gas appliances.  
m. Allow a machine to cool at least 5 minutes before  
storing.  
7. Keep all nuts, bolts, and screws tight to be sure the  
equipment is in safe working condition.  
8. Never tamper with the safety interlock system or other  
safety devices. Check their proper operation regularly.  
9. After striking a foreign object, stop the engine, disconnect  
the spark plug wire(s) and ground against the engine.  
Thoroughly inspect the machine for any damage. Repair  
the damage before starting and operating.  
10. Never attempt to make adjustments or repairs to the  
machine while the engine is running.  
11. Grass catcher components and the discharge cover are  
subject to wear and damage which could expose moving  
parts or allow objects to be thrown. For safety protection,  
frequently check components and replace immediately  
with original equipment manufacturers (O.E.M.) parts  
only, listed in this manual. Use of parts which do not  
meet the original equipment specifications may lead to  
improper performance and compromise safety!”  
12. Do not change the engine governor settings or over-  
speed the engine. The governor controls the maximum  
safe operating speed of the engine.  
General Service  
1. Never run an engine indoors or in a poorly ventilated  
area. Engine exhaust contains carbon monoxide, an  
odorless, and deadly gas.  
2. Before cleaning, repairing, or inspecting, make certain  
the blade(s) and all moving parts have stopped.  
Disconnect the spark plug wire and ground against the  
engine to prevent unintended starting.  
13. Maintain or replace safety and instruction labels, as  
necessary.  
14. Observe proper disposal laws and regulations for gas,  
oil, etc. to protect the environment.  
3. Periodically check to make sure the blades come to  
Your Responsibility  
Restrict the use of this accessory and the tractor to persons who read, understand and follow the warnings and  
instructions in this manual and on the machine.  
IMPORTANT: Models 190-670 and 190-678 Twin Rear Bagger Kits are grass collection systems designed  
for use on Cub Cadet Lawn Tractors equipped with 38-inch/42-inch cutting deck and 46-inch cutting deck  
respectively. These will NOT mount, nor operate safely or properly, on any other tractor regardless of the  
tractors compatibility with similar accessories.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
SECTION 2: LOOSE PARTS  
The grass catcher kit is shipped with following loose parts in the carton. Please remove all loose parts from the  
carton before discarding it. Compare with Figure 1 to check that no parts are missingfrom the kit or have been  
misplaced during unpacking.  
Chute Tube  
Grasscatcher Cover  
Assembly  
Support Tube  
(attached to cover)  
Mounting  
Bracket  
Grass Bag  
Assemblies  
Discharge Chute  
Assembly  
Clevis Pin &  
Hairpin Clip  
For decks with grasscatcher  
pin not pre-installed  
G
Blades  
(Model 678 only)  
H
Figure 1  
The loose parts consist of:  
1.  
2.  
3.  
4.  
5.  
6.  
7.  
One Chute Tube  
One Discharge Chute Assembly  
One Set of Blades (Model 678 only)  
Two Grass Bag Assemblies  
One Grass Catcher Cover Assembly  
One Mounting Bracket Assembly w/ Clevis Pin & Hairpin Clip  
One set of grasscatcher pin (G) and lock nut (H).  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
SECTION 3: ASSEMBLY & OPERATION  
NOTE: References to LEFT, RIGHT , FRONT and  
REAR of the tractor are from the operator’s position.  
IMPORTANT:There are two holes in the clevis pin. Be  
sure to insert the hairpin clip in the upper hole to  
properly secure the bracket assembly to the hitch plate.  
Before assembly, place the tractor on a firm and  
level surface, disengage the PTO, stop the tractor  
engine and set the parking brake.  
Attaching the Grasscatcher Cover and Bags  
Slide the support tube down through the holes in  
the left side of the mounting bracket assembly. Use  
the inside hole on the bracket assembly regardless  
of what size deck your tractor is equipped with. See  
Figure 4.  
Mounting Bracket Assembly  
NOTE: For convenience, pivot the seat forward and  
leave it in that position until the grass collector is fully  
mounted and assembled.  
Remove the hairpin clip and clevis pin from the rear  
of the mounting bracket assembly.  
Position the hooked ends of the bracket assembly  
to the outside of the hitch plate and over the  
shoulder bolts. See Figure 2.  
Mounting  
Bracket  
Support  
Tube  
Shoulder  
Bolt  
Clevis Pin  
Bell Washer  
Click Pin  
Holes  
Mounting  
Bracket Assembly  
Hitch Plate  
Figure 4  
Figure 2  
Place the grasscatcher cover assembly in position  
so that the support tube rests on the right side of  
the mounting bracket assembly. Allow the plastic  
cover to rest in the openposition . See Figure 4.  
Reinsert the clevis pin through the aligned holes in  
both the bracket assembly and the hitch plate and  
secure with the hairpin clip. See Figure 3.  
Slots  
Slots  
Clevis  
Pin  
Align these  
holes  
Hairpin Clip  
Figure 3  
Figure 5  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Attach the grass bags using the slots shown in  
Figure 5. Close the grasscatcher cover.  
Chute Deflector  
Attaching the Discharge Chute  
Raise the deck to its highest position.  
On older models: Remove the clip, if already  
installed on the deck next to the discharge chute  
opening, by removing the lock nut, spring washer  
and hex bolt that secure it. See Figure 6A.  
A
C
Hex Lock  
Cutting  
Deck  
Nut  
B
A
B
C
Spring  
Washer  
Pin  
Retainer Strap  
Clip  
Figure 7  
Place the deck at its lowest position.  
Lock the discharge chute in position by hooking the  
retainer strap over the grasscatcher pin on the  
deck. See Figure 7 for the pin position.  
Raise the deck back to its highest position.  
Insert the curved end of chute tube into the hole in  
the grass bag cover. See Figure 8.  
Hex Bolt  
A
Insert chute tube here  
Grasscatcher  
Pin  
Chute  
Tube  
Deck  
Nut  
B
Figure 6  
On older models: A grasscatcher pin (G in Figure  
1) and nut (H in Figure 1) have been supplied in the  
hardware pack. Attach these to the deck in place of  
the clip just removed. Follow Figure 6B for order of  
assembly. Make sure to secure the pin tightly.  
Raise the chute deflector on the deck and hold it  
while you position the discharge chute over the  
chute opening.  
Place the top rear edge of the discharge chute over  
the top rear edge of the chute opening.  
Push down on the discharge chute so that its front  
bottom edge rolls over the bottom of the deck; then  
slide the chute forward to the stop on the deck. See  
Figure 7.  
Figure 8  
Place the lower end of the chute tube over the  
discharge chute so that the two notches on the  
chute tube fit into the two corresponding notches on  
the discharge chute. See Figure 9.  
Notch  
Retainer  
Strap  
Chute  
Tube  
NOTE: The retainer strap is fitted at position B on the  
discharge chute. However, on older models of tractors,  
you may have to change the position of the strap  
depending on the location of the grasscatcher pin on  
the deck. Remove the retainer strap from position B on  
the discharge chute to position A or C corresponding to  
the position of the grasscatcher pin at A, B or C on the  
deck. See Figure 7.  
Figure 9  
Secure by clipping the two retainer straps of the  
discharge chute to the pins on the chute tube. See  
Figure 9.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
NOTE: The hex flange nut has a right-handed thread  
pattern. Do NOT attempt to force the nut in the incorrect  
direction. Doing so may damage the nut and create a  
safety hazard.  
Attaching Blades (Model 190-678 only)  
Remove the blades from your tractors cutting deck as  
follows.  
Remove the cutting deck from beneath the tractor,  
(refer to Deck Removal in the Maintenance section of  
your tractors operators manual for detailed  
instructions) then gently flip the deck over to  
expose its underside.  
Attach the new blades from the bagger kit as follows:  
Install the new blades packed with the bagger. Be  
sure to install the blade with the side of the blade  
marked ‘‘Bottom’’ (or with a part number stamped in  
it) facing the ground when the mower is in the  
operating position.  
Place a block of wood between the center deck  
housing baffle and the cutting blade to act as a  
stabilizer. See Figure 10.  
Use a 15/16" wrench to remove the hex flange nut  
that secures the blade to the spindle assembly. See  
Figure 10.  
Mount the smaller of the three blades to the center  
spindle. The remaining two blades are  
interchangeable.  
IMPORTANT: Use a torque wrench to tighten the blade  
spindle hex flange nut to between 70 foot-pounds and  
90 foot-pounds.  
Hex Flange Nut  
Wood Block  
Re-mount the cutting deck.  
Operation  
Open the grass bag cover by lifting the cover up as  
shown in Figure 11A. Do not remove the chute tube  
assembly from the tractor.  
Remove the grass bags by lifting these up and  
moving the bags away from the support tube  
assembly. See Figure 11B.  
To empty the grass clippings at a proper disposal  
sight, use the handle at the bottom of each grass  
bag. Holding the bag firmly as shown below in  
Figure 11C, empty the contents  
Spindle Assembly  
Figure 10  
A. Open cover  
C. Empty bag  
B. Remove bag  
Figure 11  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
SECTION 4: PARTS LIST  
17  
16  
8
14  
19  
11  
6
25  
2
7
4
24  
3
9
1
18  
12  
13  
11  
5
10  
5
26  
10  
23  
15  
27  
20*  
21*  
* Model 190-678 only  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model 190-678-100  
Ref. No. Part No.  
Description  
16587D  
Support Bracket  
1.  
2.  
3.  
4.  
5.  
6.  
7.  
9.  
10.  
11.  
12.  
13.  
14.  
15.  
16.  
16592  
Support Assembly: Grasscatcher Cover  
Cover Assembly: Grasscatcher  
Hex bolt: 1/4-20 x .620  
Hex Bolt 5/16-18 x 0.75  
Hex Bolt 1/4-20 x 0.75  
Clevis Pin  
664-04017  
710-0751  
710-3008  
710-3015  
711-0309A  
711-1421  
712-3004A  
712-3027  
714-0117  
714-0145  
723-04008  
726-3040  
731-04159  
731-04153  
731-0926B  
731-0899E  
736-0331  
736-3092  
742-3010  
742-3011  
783-0601  
783-0673  
783-0764  
783-0765  
864-0221  
Clevis Pin  
Flange Lock Nut  
Lock Nut 1/4-20  
Hairpin Clip  
Click Pin  
Chute Retainer Strap  
Push Nut  
Discharge Chute (Model 678 only)  
Discharge Chute (Model 670 only)  
Catcher Tube (Model 678 only)  
Catcher Tube (Model 670 only)  
Bell Washer  
17.  
18.  
19.  
20.  
21.  
23.  
24.  
25.  
26.  
27.  
Flat Washer  
Cutting Blade (Model 678 only)  
High Lift Blade (Model 678 only)  
Support Bracket  
Catcher Support Bracket RH  
Catcher Support Bracket LH  
Cross Support Bracket  
Bag Assembly  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MANUFACTURERS LIMITED WARRANTY FOR:  
The limited warranty set forth below is given by Cub Cadet  
LLC with respect to new merchandise purchased and used in  
the United States, its possessions and territories.  
d.  
Cub Cadet LLC does not extend any warranty for  
products sold or exported outside of the United States,  
its possesions and territories, except those sold  
through Cub Cadet LLCs authorized channels of  
export distribution.  
Parts that are not genuine Cub Cadet parts are not  
covered by this warranty.  
Service completed by someone other than an  
authorized service dealer is not covered by this  
warranty.  
Cub Cadet LLC warrants this product against defects for a  
period of two (2) years commencing on the date of original  
purchase and will, at its option, repair or replace, free of  
charge, any part found to be defective in materials or  
workmanship. This limited warranty shall only apply if this  
product has been operated and maintained in accordance  
with the Operators Manual furnished with the product, and  
has not been subject to misuse, abuse, commercial use,  
neglect, accident, improper maintenance, alteration,  
vandalism, theft, fire, water, or damage because of other peril  
or natural disaster. Damage resulting from the installation or  
use of any accessory or attachment not approved by Cub  
Cadet LLC for use with the product(s) covered by this manual  
will void your warranty as to any resulting damage.  
e.  
f.  
g.  
Transportation charges and service calls are not  
covered.  
No implied warranty, including any implied warranty of  
merchantability of fitness for a particular purpose,  
applies after the applicable period of express written  
warranty above as to the parts as identified. No other  
express warranty, whether written or oral, except as  
mentioned above, given by any person or entity,  
including a dealer or retailer, with respect to any product,  
shall bind Cub Cadet LLC. During the period of the  
warranty, the exclusive remedy is repair or replacement  
of the product as set forth above.  
Normal wear parts or components thereof are subject to  
separate terms as follows: All normal wear parts or  
component failures will be covered on the product for a period  
of 90 days regardless of cause. After 90 days, but within the  
two year period, normal wear part failures will be covered  
ONLY IF caused by defects in materials or workmanship of  
OTHER component parts. Normal wear parts and  
components include, but are not limited to: batteries, belts,  
blades, blade adapters, grass bags, rider deck wheels, seats,  
snow thrower skid shoes, shave plates, auger spiral rubber,  
and tires.  
The provisions as set forth in this warranty provide the  
sole and exclusive remedy arising from the sale. Cub  
Cadet LLC shall not be liable for incidental or  
consequential loss or damage including, without  
limitation, expenses incurred for substitute or  
replacement lawn care services or for rental expenses to  
temporarily replace a warranted product.  
HOW TO OBTAIN SERVICE: Warranty service is available,  
WITH PROOF OF PURCHASE, through your local authorized  
service dealer. To locate the dealer in your area, check your  
Yellow Pages, or contact Cub Cadet LLC at P.O. Box 361131,  
Cleveland, Ohio 44136-0019, or call 1-877-282-8684, or log  
Some states do not allow the exclusion or limitation of  
incidental or consequential damages, or limitations on how  
long an implied warranty lasts, so the above exclusions or  
limitations may not apply to you.  
In no event shall recovery of any kind be greater than the  
amount of the purchase price of the product sold. Alteration  
of safety features of the product shall void this warranty.  
You assume the risk and liability for loss, damage, or injury to  
you and your property and/or to others and their property  
arising out of the misuse or inability to use the product.  
This limited warranty does not provide coverage in the  
following cases:  
a.  
The engine or component parts thereof. These items  
carry a separate manufacturers warranty. Refer to  
applicable manufacturers warranty for terms and  
conditions.  
This limited warranty shall not extend to anyone other than the  
original purchaser or to the person for whom it was purchased  
as a gift.  
b.  
c.  
Log splitter pumps, valves, and cylinders have a sepa  
rate one year warranty.  
Routine maintenance items such as lubricants, filters,  
blade sharpening, tune-ups, brake adjustments, clutch  
adjustments, deck adjustments, and normal  
deterioration of the exterior finish due to use or  
exposure.  
HOW STATE LAW RELATES TO THIS WARRANTY: This  
limited warranty gives you specific legal rights, and you may  
also have other rights which vary from state to state.  
Cub Cadet LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019; Phone: 1-877-282-8684  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Compaq Tablet TC1000 User Manual
Conair Food Processor NE4 User Manual
Continental Refrigerator Refrigerator R 404A User Manual
Earthquake Sound Speaker SWS 10X 4 OHM User Manual
Electro Voice Microphone RE90L User Manual
Everpure Water System CG53 20S User Manual
FEIN Power Tools Dust Collector 9 88 35 User Manual
Fender Musical Instrument Amplifier PR 241 User Manual
Garland Double Oven MST47R User Manual
Gigabyte Network Card GA 8IP775 Series User Manual