Ovens with
FL-2269
Microprocessor Controls
Rev. 10 (6/08)
Page 1 of 13
5925 Heisley Road • Mentor, OH 44060-1833
INSTALLATION, OPERATION and MAINTENANCE MANUAL
for Cres Cor
CONVECTION and RETHERM OVENS
with MICROPROCESSOR CONTROLS
CO151FUA12B-Q1
CO151FPUA12B-Q1
CO151F1818B-Q1
RO151FUA18B-Q1
RO151F1332B-Q1
CO151HUA6B-Q1
CO151H189B-Q1
CO151XUA5B-Q1
CO151X185B-Q1
Download from Www.Somanuals.com. All Manuals Search And Download.
Ovens with
FL-2269
Microprocessor Controls
Rev. 10 (6/08)
Page 3 of 13
5925 Heisley Road • Mentor, OH 44060-1833
INSTALLATION INSTRUCTIONS
VENTING YOUR OVEN:
3. Most jurisdictions consider our low-temperature ovens
(maximum temperature is 350°F/177°C) as low-heat
appliances not requiring vent hoods.
1. The purpose of ventilating hoods is to direct and capture
smoke, grease-laden vapors, heat, odors, or fumes.
2. Low temperature equipment (maximum temperature
250°F/121°C) does not produce heat, odors, fumes, grease-
laden vapors or smoke and is not required to be vented.
4. Installation must conform with local codes. The authority
having jurisdiction of enforcement of the codes will have the
responsibility for making interpretations of the rules.
UNIT SPECIFICATIONS: All units use three (3) elements (2670 watts each).
All units are rated 8200 watts. Water units have one (1) immersion element (1850 watts).
ELECTRICAL SPECS
(AC SERVICE)
POWER SUPPLY REQUIREMENT
ALL 3 PHASE IS 3 WIRE + GROUND
MODEL NOS.
ELEC. LOAD
CONVECTION OVENS Volts
Ph
Hz.
Amps Volts Amps
Ph
Volts
NEMA
CO151FUA12B2081Q1
CO151FUA12B2401Q1
208
240
1
1
60
60
39
34
208
240
50
50
1
1
208
240
6-50P
6-50P
CO151FUA12B2083Q1
CO151FUA12B2403Q1
208
240
3
3
60
60
23
20
208
240
30
30
3
3
208
240
L15-30P
L15-30P
CO151FPUA12B2081Q1
CO151FPUA12B2401Q1
208
240
1
1
60
60
39
34
208
240
50
50
1
1
208
240
6-50P
6-50P
CO151FPUA122083Q1
CO151FPUA122403Q1
208
240
3
3
60
60
23
20
208
240
30
30
3
3
208
240
L15-30P
L15-30P
CO151F1818B2081Q1
CO151F1818B2401Q1
208
240
1
1
60
60
39
34
208
240
50
50
1
1
208
240
6-50P
6-50P
CO151F1818B2083Q1
CO151F1818B2403Q1
208
240
3
3
60
60
23
20
208
240
30
30
3
3
208
240
L15-30P
L15-30P
RETHERM OVENS
RO151FUA18B2081Q1
RO151FUA18B2401Q1
208
240
1
1
60
60
39
34
208
240
50
50
1
1
208
240
6-50P
6-50P
RO151FUA18B2083Q1
RO151FUA18B2403Q1
208
240
3
3
60
60
23
20
208
240
30
30
3
3
208
240
L15-30P
L15-30P
RO151F1332B2081Q1
RO151F1332B2401Q1
208
240
1
1
60
60
39
34
208
240
50
50
1
1
208
240
6-50P
6-50P
RO151F1332B2083Q1
RO151F1332B2403Q1
208
240
3
3
60
60
23
20
208
240
30
30
3
3
208
240
L15-30P
L15-30P
HALF-SIZE OVENS Are rated at 4700 watts (three [3] heaters at 1470 watts each)
CO151HUA6B2081Q1
CO151HUA6B2401Q1
208
240
1
1
60
60
24
21
208
240
30
30
1
1
208
240
6-30P
6-30P
CO151HUA6B2083Q1
CO151HUA6B2403Q1
208
240
3
3
60
60
15
13
208
240
20
20
3
3
208
240
L15-20P
L15-20P
CO151H189B2081Q1
CO151H189B2401Q1
208
240
1
1
60
60
24
21
208
240
30
30
1
1
208
240
6-30P
6-30P
CO151H189B2083Q1
CO151H189B2403Q1
208
240
3
3
60
60
15
13
208
240
20
20
3
3
208
240
L15-20P
L15-20P
CO151XUA5B2081Q1
CO151XUA5B2401Q1
208
240
1
1
60
60
24
21
208
240
30
30
1
1
208
240
6-30P
6-30P
CO151XUA5B2083Q1
CO151XUA5B2403Q1
208
240
3
3
60
60
15
13
208
240
20
20
3
3
208
240
L15-20P
L15-20P
CO151X185B2081Q1
CO151X185B2401Q1
208
240
1
1
60
60
24
21
208
240
30
30
1
1
208
240
6-30P
6-30P
CO151X185B2083Q1
CO151X185B2403Q1
208
240
3
3
60
60
15
13
208
240
20
20
3
3
208
240
L15-20P
L15-20P
All models are designed for AC Service. Model numbers may have the letters: P, L, M, T, Q5, Q10 or S.
Download from Www.Somanuals.com. All Manuals Search And Download.
Ovens with
FL-2269
Microprocessor Controls
Rev. 10 (6/08)
Page 4 of 13
5925 Heisley Road • Mentor, OH 44060-1833
INSTALLATION INSTRUCTIONS (continued)
Note: Cold food is NOT to be added when unit is operating
in HOLD mode. For HOLD mode, preheat unit to
180°F/82°C for 60 minutes.
HOW TO INSTALL CABINETS:
1. Remove all packing material from inside and outside of
cabinet.
2. Position cabinet on level floor; install the cabinet
interior (pan slides) if not already installed.
3. Plug power cord into proper wall receptacle.
CAUTION
To install stacking units, refer to instruction sheet FL-2211,
Stacking Installation.
OPERATING INSTRUCTIONS
MICROPROCESSOR
CONTROL
POWER SWITCH
TM
Roast-N-Hold +
MODE
TIME
/
TEMPERATURE
SETPOINTS
( I )
ON
COOK
PROBE
TIMED
PROBE
TIME
SELECT
SET
HEAT
COOK
START
HOLD
OVEN
TEMP
STOP
HOLD
( 0 )
OFF
POWER
Figure 1: Control Panel
HOW TO START UNIT:
(for first-time operation only)
A new oven needs to “burn off” factory oils and glue before
it’s first use. Do NOT load food into oven until this has
been done!
COOKING TEMPERATURE:
1. Press the COOK button and the display will show the
cook/retherm temperature.
2. Use the UP and DOWN arrows to set the desired
temperature.
1. Push power switch to “ON”.
3. Press the SET button to enter the temperature into the
control.
2. Press the SELECT button; choose the TIMED mode.
NOTE: Press the OVEN TEMP button at any time to view
3. Press the COOK button and set the temperature to
the actual oven temperature.
350°F/177°C.
4. Press the HOLD button and set the temperature to
HOLDING TEMPERATURE:
For HOLD mode, preheat unit to 180°F/82°C for 60 minutes.
150°F/66°C.
5. Press the PROBE/TEMP button and set the timer to
one (1) hour.
1. Press the HOLD button; the display will show the
holding temperature.
6. Allow oven to run automatically for one (1) hour of
COOK/RETHERM cycle and 30 minutes of HOLD
cycle.
2. Use the UP and DOWN arrows to set the desired
temperature.
NOTE: Proper food holding temperature is 140°F/60°C or
HOW TO SET THE CONTROL
FOR TIMED COOK OPERATION:
Press the SELECT button to choose the TIMED mode.
higher.
3. Press the SET button to enter the temperature into the
control.
COOKING TIME:
1. Press the PROBE/TIME button. The display will show
the cook/retherm time.
4. Press the START button and the display shows the
remaining time in the cook/retherm cycle.
NOTE: The control will beep after it times down to zero;
it will then automatically switch to the HOLD
mode. The display will then show the hold
setpoint temperature.
2. Use the UP and DOWN arrows to set the desired time.
3. Press the SET button to enter the time into the control.
Download from Www.Somanuals.com. All Manuals Search And Download.
Ovens with
FL-2269
Microprocessor Controls
Rev. 10 (6/08)
Page 5 of 13
5925 Heisley Road • Mentor, OH 44060-1833
OPERATING INSTRUCTIONS (continued)
7. The oven will beep and automatically switch to the
HOLD mode at the end of the cooking cycle. The Cook
lamp will go out and the Hold lamp will light up.
HOW TO SET THE CONTROL, continued
FOR PROBE COOK OPERATION:
Press the SELECT button to choose the probe mode.
Probe Cooking
See “HOW TO SET THE CONTROL” (on page 5) for
programming instructions.
PROBE TEMPERATURE:
1. Press the PROBE/TIME button. The display will show
the probe setpoint temperature.
1. Push power switch to “ON”.
2. Use the UP and DOWN arrows to set the desired
temperature.
2. Press the SELECT button and choose the Probe mode.
3. Insert the probe jack into the receptacle located inside
the oven top, near the fans. The probe temperature
display will show the digital temperature of the probe.
3. Press the SET button to enter the temperature into the
control.
4. Put sanitized probe into center of food product. Make
sure food is in the center of the pan and the pan is
centered in the oven.
NOTE: Press the OVEN TEMP button at any time to view
the actual oven temperature. Press the START
button and the display will show the actual probe
temperature.
5. Press the start button. The cook lamp will light up and
the display will show the internal temperature of the
food being cooked.
NOTE: The control will beep when the probe setpoint
temperature has been reached and then will
automatically switch to HOLD mode. The display
will then show the hold setpoint temperature.
NOTE: Do NOT change the mode of the controls (probe
or timed) while oven is operating in a Cook/
Retherm cycle. Oven must be in the HOLD cycle
to change the timer or probe operation.
To manually end the COOK/RETHERM, PROBE, or
HOLD mode:
Press the STOP button during any of the above modes and
the control will end that mode. If in the Cook/Retherm or
Probe mode, the control will automatically switch into the
HOLD mode.
HOW TO SET HOLD-ONLY MODE:
1. Push power switch to “ON”.
2. Press the STOP button and oven will switch to HOLD
cycle.
3. Press the HOLD button and set the desired hold
temperature.
HOW TO OPERATE WITH FOOD:
Manual (Timed mode) Operation
See “HOW TO SET THE CONTROL” (on page 4) for
programming instructions.
NOTE: Cold food is NOT to be added when unit is
operating in HOLD mode. For HOLD mode,
preheat unit to 180°F/82°C for 60 minutes.
1. Push power switch to “ON”.
2. Press the SELECT button and choose the TIMED
mode.
HOW TO SHUT DOWN OVEN:
Push switch to “OFF”.
3. Press the COOK button and set to desired temperature.
4. Press the PROBE/TIME button and set to the desired
time.
5. Press the HOLD button; set desired temperature.
CAUTION
6. Place the food into oven. Close door and double check
cooking time and temperatures. Then press the START Ventilating fans will continue to run until the cabinet is
button to start the cooking/retherm cycle and the Cook
LED will light up.
cool. Do NOT disconnect the power supply to the cabinet
while the ventilating fan is still operating.
Download from Www.Somanuals.com. All Manuals Search And Download.
Ovens with
FL-2269
Microprocessor Controls
Rev. 10 (6/08)
Page 6 of 13
5925 Heisley Road • Mentor, OH 44060-1833
OPERATING INSTRUCTIONS (continued)
WARNING
BEFORE cleaning the cabinet:
Cleaning Hints:
1. Use the mildest cleaning procedure that will do the job.
1. Unplug cord from wall. Allow cabinet to
cool.
2. Always rub in the direction of the polish lines to avoid
scratching the surface.
2. Do NOT hose cabinet with water.
3. Do NOT get water on controls.
3. Use only a soft cloth, sponge, fibrous brushes, plastic
or stainless steel pad for cleaning and scouring.
4. Rinse thoroughly with fresh water after every cleaning
operation.
4. Do NOT use abrasives or harsh
chemicals.
5. Always wipe dry to avoid water marks.
ꢀ Wipe up spills as soon as possible.
ꢀ Clean regularly to avoid heavy dirt build-up.
HOW TO CLEAN THE UNIT:
SOIL
CLEANER
Soap, ammonia or mild
METHOD
1. Sponge on with cloth
2. Rinse
ROUTINE CLEANING
detergent* and water.
CABINET
STUBBORN SPOTS,
STAINS
Mild abrasive made for
Stainless Steel.
1. Apply with damp sponge or cloth.
2. Rub lightly.
Inside and Outside
(Stainless Steel)
BURNT ON FOODS OR
GREASE
Chemical oven cleaner
made for Stainless Steel.
Follow oven cleaner manufacturer’s
directions.
HARD WATER SPOTS &
SCALE
1. Swab or wipe with cloth.
2. Rinse and dry.
Vinegar
* Mild detergents include soaps and non-abrasive cleaners
MAINTENANCE INSTRUCTIONS
TROUBLE-SHOOTING GUIDE
WARNING
IF UNIT GETS TOO HOT OR WON’T SHUT OFF, DISCONNECT
POWER AT BRANCH PANEL. DO NOT UNPLUG CORD!
If hot unit is NOT working, first check the following causes:
1. Cord is unplugged from wall outlet.
2. Circuit breaker/fuse to wall outlet is blown.
3. Switch is turned off.
4. Thermostat is turned off, or is set too low.
Download from Www.Somanuals.com. All Manuals Search And Download.
Ovens with
FL-2269
Microprocessor Controls
Rev. 10 (6/08)
Page 7 of 13
5925 Heisley Road • Mentor, OH 44060-1833
MAINTENANCE INSTRUCTIONS
TROUBLE-SHOOTING GUIDE (continued)
PROBLEM
POSSIBLE CAUSE
SOLUTION
1. Fuse
2. Control
3. Sensor
4. Heater contactor
5. Loose wiring at heater contactor
6. On/Off Switch
1. Replace
2. Replace
3. Replace
4. Replace
5. Replace
6. Replace
Cabinet does not heat, or doesn’t heat
properly
1. On/Off Switch
2. Fuse
3. Blower
1. Replace
2. Replace
3. Replace
4. Replace
Blowers do not operate
4. Control
Heater will not shut off
Vent fans do not shut off
1. Control defective
1. Replace
1. Replace
2. Wait until it cools
1. Vent fan switch defective
2. Control compartment is still hot.
Check “Heater will not shut off”
1. Fuse
2. Vent fan switch defective
3. Vent fan defective
1. Replace
2. Replace
3. Replace
Vent fans do not operate (See Note)
Control will not switch from “COOK” to
“HOLD” (timed mode)
1. Oven is in “PROBE” mode.
2. Control defective
1. Switch to “TIMED” mode
2. Replace
1. Oven is in the “TIMED” mode
2. Probe not plugged in
3. Control defective
1. Switch to “PROBE” mode
2. Plug in probe
3. Replace
Control will not switch from “COOK” to
“HOLD” (probe mode)
1. Oven in “TIMED” mode
1. Switch to “PROBE” mode
2. Probe temperature setting lower than 2. Set probe temperature to
Control will not switch to “COOK” (probe
mode)
probe temperature
3. Probe not plugged in
4. Control defective
desired temperature
3. Plug in probe
4. Replace
NOTE: Vent fans will not operate until the control compartment requires ventilation to limit temperatures. Replacement
of electrical components must be done by a qualified electrician.
Refer to our Service Agency list, FL-1400 (found in the back of this manual), of authorized service centers.
Instructions for replacing parts are included in replacement parts list.
Download from Www.Somanuals.com. All Manuals Search And Download.
Ovens with
FL-2269
Microprocessor Controls
Rev. 10 (6/08)
Page 8 of 13
5925 Heisley Road • Mentor, OH 44060-1833
REPLACEMENT PARTS
Include all information on nameplate when ordering parts
2
1
TM
Roast-N-Hold +
MODE
TIME / TEMPERATURE
SETPOINTS
( I )
ON
COOK
PROBE
TIMED
PROBE
TIME
SELECT
SET
HEAT
COOK
START
HOLD
OVEN
TEMP
STOP
HOLD
( 0 )
OFF
POWER
FIGURE 2: CONTROL PANEL
Hot Unit Replacement Parts
ITEM DESCRIPTION
1. Switch (On/Off)
Part No.
0808-113-01-K
ITEM DESCRIPTION
PARTS for 8200W, 1-PH UNITS
21. Power Cord
Part No.
0810-124
0810-161
0811-261
0811-262
0818-061
Thermostat/Timer, Cooking/
Holding
2.
0848-070-02
Power Cord (Pass-thru)
22. Heater Kit, 208V
Heater Kit, 240V
3. Vent Fan
4. Fan Guard
5. Fuse (Before 7-08)
Fuse (After 7-08)
Fuse Holder (Before 7-08)
Fuse Holder (After 7-08)
8. Terminal Block, front
9. Terminal Block, rear
10. Switch, Fan
11. Hi Limit Switch
12. Sensor
13. Sensor Bushing
0769-174
0769-167
0807-058
0807-151
0807-048
0807-150
0852-096
0852-093
0848-034
0848-079
23. Strain Relief
PARTS for 8200W, 3-PH UNITS
21. Power Cord
0810-132
0810-162
0811-261
0811-262
0818-050
Power Cord (Pass-thru)
22. Heater Kit, 208V
Heater Kit, 240V
23. Strain Relief
PARTS for 4700W, 1-PH UNITS
21. Power Cord
22. Heater Kit, 208V
Heater Kit, 240V
23. Strain Relief
0810-163
0811-020-K
0811-020-01-K
0818-050
0848-073-01
0818-014
14. Connector, probe (receptacle) 0848-059-01
PARTS for 4700W, 3-PH UNITS
21. Power Cord
Probe 1.5” long
Probe 6” long
0848-059-02
0848-059-04
0810-164
22. Heater Kit, 208V
Heater Kit, 240V
0811-020-K
0811-020-01-K
0818-050
23. Strain Relief
Download from Www.Somanuals.com. All Manuals Search And Download.
Ovens with
FL-2269
Microprocessor Controls
Rev. 10 (6/08)
Page 9 of 13
5925 Heisley Road • Mentor, OH 44060-1833
REPLACEMENT PARTS (continued)
FULL SIZE CABINET REPLACEMENT PARTS:
MODEL PREFIX CO-151, RO-151 (“Q” Series)
DESCRIPTION
Hot Unit, 208V, 1PH
Hot Unit, 208V, 3PH
Hot Unit, 240V, 1PH
Hot Unit, 240V, 3PH
Door Latch Kit
-F1332
-FUA (12), (18)
HU675017Q1
HU675018Q1
HU675019Q1
HU675020Q1
1006-120-01-K
1006-120-02-K
0519-074-K
-FPUA (12), (18)
HU675062Q1
HU675064Q1
HU675063Q1
HU675065Q1
1006-120-01-K
1006-120-02-K
0519-074-K
-F1818
HU675058Q1
HU675060Q1
HU675059Q1
HU675061Q1
1006-120-01-K
1006-120-02-K
0519-074-K
1221-543-K
0861-184
HU675021Q1
HU675022Q1
HU675023Q1
HU675024Q1
1006-120-01-K
1006-120-02-K
0519-074-K
1221-541-K
0861-197-K
1104-106
Door Strike Kit
Door Hinge
Door Assembly
1221-525-K
1221-525-K
Door Gasket
0861-185-K
0861-185-K
Angles/Racks
1104-108
0621-281-K
0621-281-K
Side Handles (2), Black
Recessed
0911-102
0911-102
0911-102
0911-102
HALF SIZE CABINET REPLACEMENT PARTS:
MODEL PREFIX CO-151, RO-151 (“Q” Series)
DESCRIPTION
Hot Unit, 208V, 1PH
Hot Unit, 208V, 3PH
Hot Unit, 240V, 1PH
Hot Unit, 240V, 3PH
Door Latch Kit
-HUA6
-H189
-X185
-XUA5
HU675033Q1
HU675034Q1
HU675035Q1
HU675036Q1
1006-120-01-K
1006-120-02-K
0519-074-K
HU675041Q1
HU675042Q1
HU675043Q1
HU675044Q1
1006-120-01-K
1006-120-02-K
0519-074-K
1221-541-K
0861-197-K
1104-106
HU675033Q1
HU675034Q1
HU675035Q1
HU675036Q1
1006-120-01-K
1006-120-02-K
0519-074-K
1221-546-K
0861-251
HU675041Q1
HU675042Q1
HU675043Q1
HU675044Q1
1006-120-01-K
1006-120-02-K
0519-074-K
Door Strike Kit
Door Hinge
Door Assembly
1221-525-K
1221-545-K
Door Gasket
0861-185-K
0861-250-K
Angles/Racks
0621-281-K
1104-107
0621-281-K
Download from Www.Somanuals.com. All Manuals Search And Download.
Ovens with
FL-2269
Microprocessor Controls
Rev. 10 (6/08)
Page 10 of 13
5925 Heisley Road • Mentor, OH 44060-1833
REPLACEMENT PARTS
for OVENS CO or RO151F SERIES
Include all information on nameplate when ordering parts
11
10
6
8
9
5
4
23
21
7
3
FIGURE 3;
Hot Unit w/o Top cover
(For parts description, refer to page 8.)
22
14
13
12
22
FIGURE 4;
Bottom of Hot Unit, Cover Removed
(For parts description, refer to page 8.)
Download from Www.Somanuals.com. All Manuals Search And Download.
Ovens with
FL-2269
Microprocessor Controls
Rev. 10 (6/08)
Page 11 of 13
5925 Heisley Road • Mentor, OH 44060-1833
REPLACEMENT PARTS
for “PASS-THRU” OVENS CO or RO151FPUA SERIES
Include all information on nameplate when ordering parts
23
21
8
7
3
4
5
6
FIGURE 3; Hot Unit w/o Top cover
(For parts description, refer to page 8.)
11
10
9
12
13 14
22
FIGURE 4; Bottom of Hot Unit, Cover Re-
moved (For parts description, refer to page 8.)
Download from Www.Somanuals.com. All Manuals Search And Download.
Ovens with
FL-2269
Microprocessor Controls
Rev. 10 (6/08)
Page 12 of 13
5925 Heisley Road • Mentor, OH 44060-1833
WIRING DIAGRAM
30
29
1 PHASE
V
HIGH TEMP
V
26
28
G
L2
L1
FUSE
2
1
3
FUSE
4
14
HEATER
CONTACTOR
18
1
2
H1
H2
H3
HIGH LIMIT
7
6
9
12
11
17
16
8
8
10
HIGH LIMIT
6
13
A
18
19
20
21
POWER
SWITCH
14
27
BM
L
BM
R
BM
C
5
22
AC-N
110v
220v
SENSOR
OVEN
24
FAN
RTD1
RTD2
t°
t°
Temp. Control
Board
23
25
SENSOR
PROBE
15
5
HEAT
SINGLE PHASE
30
29
3 PHASE
V
HIGH TEMP
28
V
26
18
G
L3
L2
L1
FUSE
2
1
3
FUSE
4
14
HEATER
CONTACTOR
10
1
2
H1
H2
H3
HIGH LIMIT
7
9
8
12
11
17
16
8
10
HIGH LIMIT
6
13
A
18
19
20
21
POWER
SWITCH
14
27
BM
L
BM
R
BM
C
5
22
AC-N
110v
220v
SENSOR
OVEN
t°
24
FAN
RTD1
Temp. Control
Board
23
SENSOR
PROBE
15
5
HEAT
RTD2
t°
25
THREE PHASE
Download from Www.Somanuals.com. All Manuals Search And Download.
Ovens with
FL-2269
Microprocessor Controls
Rev. 10 (6/08)
Page 13 of 13
5925 Heisley Road • Mentor, OH 44060-1833
OPERATING INSTRUCTIONS
FOR OVENS WITH OPTIONAL PRODUCT KEYS
PROBE RECEPTACLE
POWER SWITCH
PRODUCT KEYS
CONTROL
MODE
SETPOINTS
ON
TIME
-
TEMPERATURE
RETHERM
COOK
PROBE
TIMED
TIME
SET
HEAT
COOK
HOLD
SELECT
PROBE
OVEN
TEMP
START
STOP
HOLD
OFF
POWER
CONTROL PANEL
The Product Keys provide automatic menu selections
(arranged in banks of 5 keys, max. 10 keys). Each Product
Key can be user programmed for desired mode (PROBE or
TIMED) and the required COOK, HOLD, and PROBE or
TIME setpoints.
Product Key Programming
1. Press the desired Product Key.
2. Press and hold the SET key until the Product Key light
begins to flash.
3. Enter the desired Mode, Cook, Hold and Probe/Time
values.
Each Product Key Lights up when pressed “ON”.
The Product Key Light will go “OFF” when pressed a
second time or when changing any setpoint value. This
returns the control to manual operation.
NOTE: Press the SET key after each value is changed or
added to accept and store a new setpoint.
4. To exit; Press the SET key for a few seconds until the
Product Key light is extinguished.
Extra Replacement Parts:
Product Key (5 Keys) 0848-072
For Hot Unit Replacement, See Page 9:
The Hot Unit suffix number will be Q5 (5 Keys)
or Q10 (10 Keys) instead of Q1
Download from Www.Somanuals.com. All Manuals Search And Download.
|