Tumble Dryer
Instruction Book
TCS3
You must read these instructions prior to using the appliance and
retain them for future reference
Download from Www.Somanuals.com. All Manuals Search And Download.
Instruction booklet
TUMBLE DRYER
Contents
GB
Installation, 2
Door reversal instructions
Where to put your dryer
Ventilation
Water drain
Electrical connection
Before you start using your dryer
Dryer description, 3
The front
The back
Control panel
Start and programmes, 4
Choosing a programme
Laundry, 5-6
Sorting your laundry
Wash care labels
Special clothing items
Drying times
Warnings and Suggestions, 7
General safety
Disposal
Saving energy and respecting the environment
Maintenance and Care, 8
Switching off the electricity
Cleaning the filter after each cycle
Empty the water container after each cycle
Check the drum after each cycle
Cleaning the condenser unit
Cleaning the dryer
Troubleshooting, 9
Service, 10
Spare parts
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Electrical connections
! Keep this instruction booklet on hand in order to refer to it
when necessary. Take it with you when you move, and
should you sell this appliance or pass it on to another
party, make sure that this booklet is supplied along with
the dryer so that the new owner may be informed about
warnings and suggestions on how the dryer works.
! Read these instructions carefully; the following pages
contain important information on installation and
suggestions on how the appliance works.
GB
Make sure of the following before you insert the plug into
the the electrical socket:
ꢀ
The socket must be grounded.
The socket must be able to sustain the machines
ꢀ
maximum power, which is indicated on the rating label
(see Dryer Description).
Power voltage must be within the values indicated on
ꢀ
the rating label (see Dryer Description).
The socket must be compatible with the dryers plug.
ꢀ
Should this not be the case, replace the plug or the socket.
! The dryer must not be installed outdoors, even if the space is
sheltered. It can be very dangerous if it is exposed to rain
or storms.
Door Reversal Instructions
Door catch
Hinge
! Once installed, the dryers electrical wire and plug must
be within easy reach.
Door latch
! Do not use extension cords.
! The power cord must not be bent or squashed.
! The power cord supplied is fitted with a BS1363 plug and a
13 amp BS1362 fuse. If you need to replace the fuse, use only
those rated at 13 amp (13A) and ASTA approved to
BS1362.
Moulded plug
! The plug must not be used without
the fuse cover in place.
Hinge
If a replacement fuse holder/cover
is required, it must be of the same
colour coding or wording as shown
on the base of the plug.
Replacements are available from
authorised dealers.
The door of your dryer is reversible and can easily be
changed. Exchange diagonally hinge brackets and
blanking screws. Exchange door latch and catch with their
opposite blanking plates (see diagram above).
Where to put your dryer
Changing the plug
The wires in the power cord are coloured in accordance with
the following:
Green and Yellow
(Earth) wire to terminal
ꢀ
Place your dryer at a distance from gas ranges,
stoves, heaters, or cook tops because flames can
damage the appliance.
marked ‘E’, symbol
or coloured green and
yellow.
,
ꢀ
If you are going to install the appliance under a work
13A ASTA approved
fuse to BS1362.
counter, be sure to leave a 10mm space between the
top and any other objects on or above the machine
and a 15mm space between the sides and lateral
furnishings or walls. This is to ensure proper air circulation.
Make sure that the back vents are not obstructed.
Blue (Neutral) wire to
terminal marked ‘N’ or
coloured black.
Brown (Live) wire to
terminal marked ‘L’ or
coloured red.
Cord clamp
Ventilation
! If the plug being replaced is a non-rewirable type, then
the cut-off plug must be disposed of safely. DO NOT leave
it where it can be inserted into a socket and create a shock
hazard.
! The power supply cord should be checked periodically and
replaced by a cord specially prepared for this dryer and fitted
only by authorised technicians (see Service). New or longer
power cords are supplied at an extra charge by authorised
dealers.
When the dryer is in use, there has to be adequate
ventilation. Make sure you put your dryer in an environment
that is not damp and has proper air circulation throughout.
Airflow around the dryer is essential to condense the
water produced during the washing, the dryer will not
operate efficiently in an enclosed space or cupboard.
! If using the dryer in a small or cold room some
condensation could be experienced.
! The manufacturer denies any responsibility should any of
these rules not be followed.
! If in doubt about any of the above consult a qualified
electrician.
Water drain
If your dryer is installed next to a drain the water can be
plumbed into this drain. This does away with the need to
empty the water container. Simply remove the top hose
from its top fitting at the rear of the dryer and plumb the
hose provided to the drain.
Before you start using your dryer
Once you have installed your dryer and before you use it,
clean the inside of the drum to remove any dust that could
have accumulated during transport.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Dryer Description
To open the door
The features
GB
Press and release the front
panel in position shown
Rating plate
Water container
Door lat
Model &
Serial
numbers
Door catch
Air intake
grille
Filter
Condenser cover handle
(Pull to open)
Control panel
Empty Water
Light
HEAT
ALARM
Indicator
Button
Button
START
Button
PROGRAMMES
Drying Guide
Knob
The START button begins drying a selected
programme (see Start and Programmes).
The Drying Guide allows you to consult a user friendly
table of fabric types and load capacities.
The HEAT button selects drying temperature (see
Start and Programmes).
Out: HIGH Heat
The Empty Water light signals that the water container
is full and must be emptied. The light will take a few
seconds to go out after replacing the empty water
container, the dryer must be running for this to happen.
In: GENTLE (LOW) Heat
The ALARM buzzer signals the end of a drying cycle.
Out: buzzer ON
In: buzzer OFF
The PROGRAMMES knob sets the programme:
rotate until the indicator is pointing to the programme
you want to select (see Start and Programmes).
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Start and Programmes
Choosing a programme
6. If you wish the buzzer to sound at the end of the
GB
programme, press the ALARM button.
1. Plug the dryer into the electrical socket.
7. Press the START button to begin.
During the drying programme, you can check on
your laundry and take out items that are dry
while others continue drying. When you close
the door again, press the START button in order
to resume drying.
2. Sort your laundry according to fabric type (see
Laundry).
3. Open the door and make sure the filter is clean
and in place and the water container is empty
and in place (see Maintenance).
8. About 10 minutes before the programme is
completed, it enters the final COOL TUMBLE
phase (fabrics are cooled), which should always
be allowed to complete.
4. Load the machine and make sure items are not
in the way of the door seal. Close the door.
5. Choose a drying programme by checking the
Programmes table (see Programmes) as well as
the indications for the type of fabric (see
Laundry).
9. Open the door, take the laundry out, clean the
filter and replace it. Empty the water container
and replace it (see Maintenance).
- Set the temperature with the HEAT button.
- Select a programme or drying time by rotating
the PROGRAMME knob.
10. Unplug the dryer.
Water container and empty water light
If you have plumbed your dryer to a drain this light can be ignored, as there is no need to empty the water
container.
When this light is on (not flashing) it reminds you to empty the water container.
If the water container fills during a programme, the light flashes and the dryer does the Cool Tumble phase (see
Programmes). You must empty the water container and restart the dryer or the clothes will not dry. After
re-starting the dryer the light will take a few seconds to go out.
To avoid this always empty the water container each time you use the dryer (see Maintenance).
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Start and Programmes
Programmes
GB
Note:
Programme
What it does...
How to set it...
1. Position the PROGRAMMES knob
Options available:
Alarm, High or Low Heat
Dries your clothes, ready for
putting away.
on
.
2. Select High or Gentle Heat.
3. Select Alarm option, if required.
4. Press the START button.
Cupboard dry
! Do not dry Synthetics or
Acrylics on High Heat
(see Laundry).
1. Position the PROGRAMMES knob
Options available:
Alarm
Brief programme
on
.
(approximately 10 minutes)
that softens fibres of clothing
that is ready for ironing.
Speedy Iron
2. Select High Heat.
3. Select Alarm option, if required.
4. Press the START button.
! This is not a drying
programme (see below).
Timed Drying
1. Position the PROGRAMME knob
on the desired time: 140, 120, 110,
100, 90, 80, 70, 60, 50, 40, 30 or
20.
2. Select High or Gentle Heat.
3. Select Alarm option if required.
4. Press the START button.
Options available:
Alarm, High or Low Heat
For drying small loads (less than
1kg) or if you prefer to use a
timed programme.
(140, 120, 110,
100, 90, 80, 70,
60, 50, 40, 30 or
20 minutes)
! Do not dry Synthetics or
Acrylics on High Heat
(see Laundry).
Should be used if you prefer a
damper result than Cupboard
dry.
Consult suggested drying
times (see Laundry).
eg. a damper result suitable for
ironing.
The last 10 minutes of
these programmes is the
Cool Tumble phase (see
below).
1. Position the PROGRAMME knob
Options available:
Alarm
Cool Tumble Brief programme
(approximately 10 minutes)
that cools fibres of clothing.
on
.
2. Select Alarm option, if required.
3. Press the START button.
Speedy Iron
‘Speedy Iron’ is a short 10 minute programme (8 minutes of heat followed by a 2 minute cool tumble period)
which fluffs the fibres of clothing that have been left in the same position/location for an extended period of time.
The cycle relaxes the fibres and makes them easier to iron and fold.
! ‘Speedy Iron’ is not a drying programme and should not be used for wet articles of clothing.
For best results:
1. Do not load more than the maximum capacity.
These numbers refer to the dry weight:
Fabric
Maximum load
Cotton and Cotton mixtures
Synthetics
2.5kg
2kg
Denim
2kg
2. Unload the dryer immediately after the end of the drying programme, hang, fold or iron the articles and put
them away in the closet. Should this not be possible repeat the programme.
The ‘Speedy Iron’ effect varies from one fabric to the next. It works well on traditional fabrics like Cotton or
Cotton mix, and less well on acrylic fibres and on materials such as Tencel®.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Laundry
Sorting your laundry
Wash Care Labels
GB
ꢀ
Check symbols on clothing labels to make sure
that the articles can be tumble dried.
Sort laundry by fabric type.
Empty pockets and check buttons.
Close zippers and hooks and tie loose belts and
strings.
Wring out each item in order to eliminate as much
excess water as possible.
Look at the labels on your garments, especially when
tumble drying for the first time. The following symbols
are the most common:
ꢀ
ꢀ
ꢀ
May be tumble dried
ꢀ
Do not tumble dry
Tumble dry at high heat setting
Tumble dry at low heat setting
! Do not load dripping wet clothes into the dryer.
Maximum load size
Items not suitable for tumble drying
Do not load more than maximum capacity.
These numbers refer to dry weight:
Natural fibres: 6kg max (13lb)
ꢀ
Articles that containing rubber or rubber-like
materials or plastic film (pillows, cushions, or PVC
rainwear), any other flammable articles or objects
that contain flammable substances (towels soiled
with hair spray).
Glass fibres (certain types of draperies)
Items which have been dry cleaned
Synthetic fibres: 3kg max (6.6lb)
! DO NOT overload the dryer as this could result in
reduced drying performance.
ꢀ
ꢀ
ꢀ
Items with the ITCL Code
(see Special clothing
Typical load
items). These can be cleaned with special at-home
dry cleaning products. Follow instructions carefully.
Large bulky items (quilts, sleeping bags, pillows,
cushions, large bedspreads etc). These expand
when drying and would prevent airflow through
the dryer.
ꢀ
Clothes
Blouse
Cotton
Other
Cotton
Other
150g
100g
500g
350g
700g
5oz
3oz
Dress
1lb 2oz
12oz
Jeans
1lb 6oz
10 nappies
Shirt
1000g 2lb 3oz
Cotton
Other
300g
200g
125g
10oz
7oz
T-Shirt
4oz
Household Items
Duvet cover
(Double)
Cotton
Other
1500g 3lb 5oz
1000g 2lb3oz
Large Tablecloth
Small Tablecloth
Tea Towel
700g
250g
100g
700g
350g
500g
350g
1lb 6oz
9oz
3oz
Bath Towel
1lb 6oz
12oz
Hand Towel
Double Sheet
Single Sheet
1lb 2oz
12oz
At the end of a drying cycle, cottons could still be
damp if you grouped cottons and synthetics together. If
this happens simply give them an additional short period
of drying.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Laundry
Special clothing items
Times are approximate and can vary depending
upon:
GB
Blankets and Bedspreads: acrylic items (Acilan,
Courtelle, Orion, Dralon) must be dried with special
care on LOW heat setting. Avoid drying for a long
period of time.
ꢀ
Amount of water retained in clothes after spin
cycle: towels and delicates retain a lot of water.
ꢀ
Fabrics: items that are the same type of fabric but
Pleated or creased garments: read the manufacturer’s
drying instructions on the garment.
different textures and thicknesses may not have
the same drying time.
ꢀ
Starched articles: do not dry these with non-
starched items. Make sure that as much of the starch
solution is removed from the load as possible before
placing it in the dryer. Do not over-dry: the starch will
become powdery and leave your clothing limp, which
defeats the purpose of starch.
Quantity of laundry: single items or small loads
may take longer to dry.
ꢀ
Dryness: If you are going to iron some of your
clothes, they can be taken out while still a bit
damp. Others can be left longer if you need them
to be completely dry.
ꢀ
Heat setting.
Drying times
ꢀ
Room temperature: if the room where the dryer is
The table below presents APPROXIMATE drying
times in minutes. Weights refer to dry garments:
located is cold, it will take longer for the dryer to
dry your clothes.
ꢀ
Bulk: some bulky items can be tumble dried with
Cottons
/
care. We suggest that you remove these items
several times, shake them out, and return them to
the dryer until finished.
High (full) Heat
Drying times 800-1000rpm in washing machine
Half Load
Full Load
1kg
2kg
3kg
4kg
5kg
6kg
! Do not over-dry your clothes.
30-40 40-55 55-70 70-80
80-90 95-120
All fabrics contain a little natural moisture, which
keeps them soft and fluffy.
Synthetics
Low (gentle) Heat
Drying times on reduced spin in washing machine
Half Load
Full Load
1kg
2kg
3kg
40-50
50-70
70-90
Acrylics
/
Low (gentle) Heat
Drying times on reduced spin in washing machine
Half Load
Full Load
1kg
2kg
40-60
55-75
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Warnings and Suggestions
ꢀ
Never dry articles that are contaminated with
flammable substances (petrol, oil, paint, hair spray,
creams, cooking fat or oils).
Do not tumble dry rubber, foam rubber, plastic,
plastic foam, nappy pants or liners, polythene or
paper.
! The appliance has been designed and built
according to international safety standards.
These warnings are given for safety reasons and must
be read carefully.
GB
ꢀ
This appliance conforms to the following
EEC Directives:
ꢀ
ꢀ
ꢀ
Do not tumble dry large, very bulky items.
Do not tumble dry acrylic fibres at high temperatures.
Complete each programme with its Cool Tumble
Phase.
Do not turn off the dryer when there are still warm
items inside.
Clean the filter after each use (see Maintenance).
Empty the water container after each use (see
Maintenance).
Clean the condenser unit after regular intervals
(see Maintenance).
- 72/23/EEC and 93/68/EEC (Low Voltage Equipment)
- 89/336/EEC, 92/31/EEC and 93/68/EEC
(Electromagnetic Compatibility)
ꢀ
General safety
ꢀ
ꢀ
ꢀ
This tumble dryer has been designed for home,
and not professional use.
This dryer must be used by adults, and the instructions
ꢀ
ꢀ
in this booklet should be followed carefully.
Do not touch the appliance while barefoot or with
ꢀ
ꢀ
ꢀ
Do not allow lint to collect around the dryer.
Never climb on top of the dryer. It could result in
damage.
wet hands or feet.
Unplug the machine by pulling on the plug, not the
ꢀ
ꢀ
ꢀ
Always follow electrical standards and
requirements (see Installation).
Always buy original spare parts and accessories
(see Service).
cord.
ꢀ
Children must not be in proximity of the dryer when
in use. After using the dryer, turn it off and unplug
it. Keep the door closed to make sure that children
do not use it as a toy.
ꢀ
The appliance must be installed correctly and have
Disposal
proper ventilation. The air intake at the front of the
dryer and rear vent behind the dryer should never
be obstructed (see Installation).
ꢀ
Disposing of the packaging material: follow local
ꢀ
regulations, so the packaging can be recycled.
Disposal of your old dryer: cut the power cord and
remove the door before disposing of an old dryer.
Never use the dryer on carpeting where the pile
height would prevent air from entering the dryer
from the base.
ꢀ
ꢀ
Check to see if the dryer is empty before loading it.
ꢀ
The back of the dryer could become very hot.
Saving energy and respecting the
environment
Never touch it while in use.
Do not use the dryer unless the filter, water container
and condenser are securely in place (see
Maintenance).
Do not use liquid fabric softeners in the dryer, add
it to the final rinse of your wash.
Do not overload the dryer (see Laundry for maximum
loads).
ꢀ
ꢀ
Wring out items to eliminate excess water before
ꢀ
tumble drying (if you use a washing machine first,
select a high spin cycle). Doing this will save time
and energy during drying.
ꢀ
ꢀ
Always dry full loads - you save energy: single
ꢀ
items or small loads take longer to dry.
Clean the filter after each use to contain energy
Do not load items that are dripping wet.
Tumble dry items only if they have been washed
ꢀ
ꢀ
consumption costs (see Maintenance).
with detergent and water, rinsed and been through
the spin cycle. It is a fire hazard to dry items that
HAVE NOT been washed with water.
ꢀ
Carefully check all instructions on clothing labels
(see Laundry).
Do not dry garments that have been treated with
ꢀ
chemical products.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance and Care
Switching off the electricity
Cleaning the condenser unit
GB
! Unplug your dryer when not using it, when cleaning
it and during all maintenance operations.
Periodically (every month) remove the condenser unit
and clean any build up of fluff from between the plates
by rinsing it under the tap with cold water.
This should be done with cold water from the rear of
the condenser.
Clean the filter after each cycle
The filter is an important part of your dryer:
it accumulates lint and fluff that is formed while drying.
When finished drying, clean the filter by rinsing it
under running water or with your vacuum cleaner.
Should the filter become clogged up, the airflow inside
the dryer will be seriously compromised: drying times
lengthen and you will consume more energy. It may
also damage your dryer.
Removing the condenser:
1. Unplug the dryer and open the door.
2. Pull open the condenser cover (see diagram).
Release the three catches by turning 90˚ counter-
clockwise then pull on the grip and remove from
the dryer.
3. Clean the surface of the seals and replace, making
sure that the catches have been secured.
The filter is found in front of the dryer trim (see diagram).
Cleaning the dryer
Removing the filter:
ꢀ
1. Pull the plastic grip of the filter upwards (see diagram).
2. Clean the filter and replace it correctly.
Ensure the filter is fully located flush into the tumble
dryer trim.
External parts in metal or plastic and rubber parts
can be cleaned with a damp cloth.
Periodically clean the surface of the stainless
ꢀ
steel sensor inside the drum with vinegar to
remove water contaminates. Apply carefully with
a cloth, this will maintain the drying performance
of the dryer. The sensor is located on the plastic
vane inside the drum towards the front of the
dryer. Rotate the drum if necessary to locate it.
! Do not use the dryer without replacing the filter.
Empty the water container after each
cycle
ꢀ
Periodically (every 6 months) vacuum the front air
Pull the container out of the dryer and empty it into a
sink or other suitable drain. Replace the water
container securely.
Always check and empty the container before you
start a new drying programme.
intake grille and vents at the rear of the dryer, to
remove any build up of fluff, lint or dust. Also to
remove accumulation of fluff from the front of the
condenser and filter areas, clean occassionally
with a vacuum cleaner.
! Do not use solvents or abrasives.
! Your dryer uses special bearing components which
do not need lubrication.
! Have your dryer checked regularly by authorised
technicians to ensure electrical and mechanical safety
(see Service).
Check the drum after each cycle
Turn the drum manually in order to remove small
items (handkerchiefs) that could have been left
behind.
Water container
Filter
Tap
Rear
Front
Condenser cover
Air intake
Condenser unit
Catches
Handle
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
One day your dryer seems not to be working. Before you call your Service Centre (see Service), go through the
following troubleshooting suggestions:
GB
Problem:
Possible causes / Solution:
ꢀ
The tumble dryer won’t start.
The plug is not plugged into the socket, or not making contact.
There has been a power failure.
The fuse has blown. Try to plug another appliance into the socket.
You are using an extension cord? Try to plug the dryer’s power cord
ꢀ
ꢀ
ꢀ
directly into the socket.
The door is not closed securely?
The PROGRAMMES knob has not been set properly (see Start and
ꢀ
ꢀ
Programmes).
ꢀ
The START button has not been pressed (see Start and Programmes).
ꢀ
It is taking a long time to dry.
The filter has not been cleaned (see Maintenance).
The temperature setting is not ideal for the type of fabric you are drying
ꢀ
(see Start and Programmes, and see Laundry).
The water container needs emptying? The empty water light is flashing?
ꢀ
(see Maintenance).
The condenser needs cleaning? (see Maintenance).
The correct drying time has not been selected for the load (see Laundry).
The air intake grille or rear vents are obstructed (see Installation, and see
ꢀ
ꢀ
ꢀ
Maintenance).
The items were too wet (see Laundry).
The dryer was overloaded (see Laundry).
ꢀ
ꢀ
ꢀ
Empty water light is on and
the water container is not
full.
This is normal, the light flashes when the container is full. If the light is on
but not flashing it is just a reminder to empty the container (see Start and
Programmes).
Programme finishes and
clothes are damper than
expected.
! For safety the dryer has a maximum programme time of 4 hours. If an automatic
programme has not sensed the required final moisture in this time the dryer will
complete the programme and stop. Check the above points and run the
programme again, if the results are still damp, contact the Service Centre
(see Service).
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Service
Before calling the Service Centre:
Spare Parts
GB
ꢀ
Use the troubleshooting guide to see if you can
solve the problem yourself (see Troubleshooting).
If not, turn off the dryer and call the Service Centre
closest to you.
This dryer is a complex machine. Repairing it
yourself or having a non-authorised person try to
repair it could cause harm to one or more persons,
could damage the machine and could invalidate the
spare parts warranty.
ꢀ
Call an authorised technician if you experience problems
while using the machine.
The spare parts have been designed exclusively for
this appliance and not for other uses.
What to tell the Service Centre:
ꢀ
name, address and post code.
telephone number.
the type of problem.
the date of purchase.
ꢀ
ꢀ
ꢀ
ꢀ
the appliance model (Mod.).
ꢀ
the serial number (S/N).
This information can be found on the data label
inside the door of the machine.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Key Contacts
After Sales Service
Over 1100 trained specialists, directly employed by us, ensure that you can have complete confidence
in both the appliances and services we offer.
Repair Service and Information Help Desk
UK: 08709 066 066
Monday to Friday, 8am to 7.30pm
Saturday, 8.30am to 5.30pm
Sunday, 9.30am to 3.30pm
Republic of Ireland: 1850 302 200
Note: Our operators will require the following information:
Model number
Serial number
Extended Warranties
UK: 08709 088 088
Monday to Sunday, 8am to 8pm
Republic of Ireland: 1850 502 200
Genuine Parts and Accessories
UK: 08709 077 077
Monday to Friday, 8.30am to 5pm
Saturday, 8.30am to 12noon
Republic of Ireland: (01) 842 6836
Indesit Company UK Limited, Morley Way, Peterborough, PE2 9JB
.
PRINTED BY SIMLEX FOUR ASHES, WOLVERHAMPTON.
01/2005 195042652.01
Download from Www.Somanuals.com. All Manuals Search And Download.
|