VTX15
Guitar Amplifier
User’s Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
VTX15 Guitar Amplifier
The Front Panel:
SOLO
CLEAN EQUALIZATION
DSP
DELAY
FLANGER
FLANGER
CHORUS
1
INPUT
GAIN
LEVEL
VOLUME
LOW
MID
HIGH
POWER
2
1
CHORUS
ROTARY
T-WAH
2
I-WAH
DOUBLER
BYPASS
REVERB
SOLO
CLEAN
CD INPUT
1
2
3
4
5
6
7
8
9
10
11
12
13
CAUTION: To avoid possible damage to your hear-
ing, do not use headphones for extended periods
of time at extremely loud levels.
1: INPUT: Use this jack to connect your guitar to
the amplifier by means of a shielded instrument
cable.
12: SPEAKER: Use this jack to connect the
amplifier to an external speaker. The internal
speaker is disconnected when this jack is used.
The impedance of the external speaker must be 4
ohms or greater.
SOLO CHANNEL: A high gain channel giving you
sounds from a slight edge to serious overdrive.
2: GAIN: Use this control to adjust the amount of
distortion for the Solo channel.
3: LEVEL: Use this control to adjust the output
level of the Solo channel.
WARNING: Do not attempt to use headphones in
the Speaker jack! Permanent hearing damage
could result!
4: SOLO/CLEAN: Use this switch to select the
Solo or Clean channel. With the switch in the out
position, the Clean channel is selected. When the
switch is depressed, the Solo channel is selected.
13: POWER: Use this switch to turn the amplifier
on (top of the switch depressed) and off (bottom of
the switch depressed). The switch illuminates
when the amplifier is turned on.
CLEAN CHANNEL: A normal gain channel
designed to give you crystal clear sounds to medi-
um distortion.
14: POWER CORD (rear panel, not shown):
The grounded power cord should only be plugged
into a grounded power outlet that meets all appli-
cable electrical codes and is compatible with the
voltage, power, and frequency requirements stat-
ed on the rear panel. Do not attempt to defeat
the safety ground connection.
5: VOLUME: Use this control to adjust the output
level of the Clean channel.
6: LOW: Use this control to adjust the low fre-
quency level of the amplifier.
7: MID: Use this control to adjust the midrange fre-
DSP: THE DIGITAL EFFECTS
quency level of the amplifier.
8: HIGH: Use this control to adjust the high fre-
quency level of the amplifier.
DELAY
short delay
medium delay
long delay
“
“
9. DSP: Use this control to select one of the 16
built-in digital effects. The effects are described in
the table to the right.
FLANGER 1 slow shallow flange
FLANGER 2 fast deep flange
CHORUS 1
CHORUS 2
ROTORY
T-WAH
I-WAH
DOUBLER
BYPASS
REVERB
“
slow shallow chorus
fast deep chorus
medium-speed rotating speaker
touch-sensitive wah-wah
inverse wah-wah
adds second signal out of sync
(no effect added)
small room reverb
10: CD INPUT: Use these RCA jacks to connect
the output from a CD player or tape deck to the
amplifier. The signal at these jacks is combined
into a mono signal which is sent to the internal
power amp circuit. Use the CD or tape player’s
output level control to adjust the signal for the
proper mix with your guitar.
medium room reverb
small hall reverb
large hall reverb
11: HEADPHONES: Use this jack to connect
headphones to the amplifier. The internal speaker
is disconnected when headphones are used.
“
“
Download from Www.Somanuals.com. All Manuals Search And Download.
VTX15 Guitar Amplifier
VTX15 TECHNICAL SPECIFICATIONS:
Output Power Rating
Gain
12W RMS @ 5% THD, 4Ω, 120 VAC
Solo Ch
86dB +/-6dB @ 1kHz
46dB +/-6dB @ 1kHz
Clean Ch
CD Input
26dB +/-2dB
Maximum Input Signal Accepted
Tone Controls
2.2 volts RMS min. @ 400Hz
Low
Mid
25dB range @ 80Hz
19dB range @ 900Hz
23dB range @ 5kHz
High
Signal To Noise Ratio
Solo Ch
>50dB
>65dB
Clean Ch
Speaker Size and Rating
Power Requirements
8” Crate Custom Design 4 ohm
120 VAC, 60Hz, 30VA
100/115VAC, 50/60Hz, 30VA
230VAC, 50/60Hz, 30VA
Size and Weight
12-1/2” H x 16” W x 7-5/8” D, 19 lbs.
The VTX15 is covered with a durable Tolex material: wipe it clean with a lint-free cloth.
Never spray cleaning agents onto the cabinet. Avoid abrasive cleansers which would damage the finish.
Crate continually develops new products, as well as improves existing ones. For this reason, the specifications
and information in this manual are subject to change without notice.
Declaration of Conformity
Manufacturer’s Name: SLM Electronics
Corporate Headquarters: 1901 Congressional Drive, St. Louis, Missouri 63146
Primary Production Facility: 700 Hwy 202 W, Yellville, Arkansas, 72687
Product Type: Audio Amplifier
Products meet the regulations for compliance marking under:
ETL standards UL6500, UL60065, or UL813
CSA standards E60065 or C22.2 No.1-M90
CE safety standard EN60065
CE EMC standards EN55103 or EN55013 and EN61000
FCC standards 47CFR 15.107 and 15.109 Class B
C-tick designation Level 2, ABN #56748810738, ARBN# N222
KETI standard K60065 (limited model approval)
Compliance Support Contact: SLM Electronics, Attn: R&D Compliance Engineer
1901 Congressional Drive, St Louis, Missouri, 63146 • Tel.: 314-569-0141, Fax: 314-569-0175
@2004 SLM Electronics, a division of St. Louis Music, Inc • 1400 Ferguson Avenue • St. Louis, MO 63133
47-952-02 • 060904
Download from Www.Somanuals.com. All Manuals Search And Download.
|