Operator’s Manual
12 in. SLIDING COMPOUND
MITER SAW WITH LASER TRAC®
Model No. 137.212390
ϥ
Safety Instructions
CAUTION:
ϥ
ϥ
ϥ
ϥ
Installation
Operation
Maintenance
Parts List
Before using this Miter Saw,
read this manual and follow
all its Safety Rules and
Operating Instructions
Customer Help Line
For Technical Support
1-800-843-1682
Sears Parts &
Repair Center
1-800-488-1222
Sears, Roebuck and Co., Hoffman Estates, lL 60179 USA
Part No. 137212390001
Printed in China
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY
CRAFTSMAN ONE YEAR FULL WARRANTY
If this Craftsman tool fails due to a defect in material or workmanship within
one year from the date of purchase, call 1-800-4-MY-HOME R to arrange for
free repair (or replacement if repair proves impossible).
This warranty applies for only 90 days from the date of purchase if this product
is ever used for commercial or rental purposes.
This warranty does not include expendable parts, such as lamps, batteries,
bits or blades.
This warranty gives you specific legal rights, and you may also have other
rights which vary from state to state.
Sears, Roebuck and Co., Hoffman Estates, IL 60179
PRODUCT SPECIFICATIONS
MOTOR
Power Source ............................................................. 120V AC, 60Hz, 15 Amp
Speed ......................................................................... 4200 RPM (No load)
Brake .......................................................................... Electric
Double Insulated.......................................................... Yes
Motor Arbor Shaft Size................................................. 5/8 in.
BLADE SIZE
Diameter...................................................................... 12 in.
Arbor size.................................................................... 1 in. w/a 5/8 in. reducer
Rotating Table:
Diameter...................................................................... 11-13/16 in.
Miter Detent Stops ...................................................... 0, 15, 22.5, 31.6, 45º R & L
Bevel Positive Stops.................................................... 0, 33.9, 45º L
Cutting Capacity:
Crosscut....................................................................... 4 in. x 12-1/4 in.
Miter 45° R & L............................................................ 4 in. x 8-3/4 in. R & L
Bevel 45º L................................................................... 2-1/2 in. x 12-1/4 in. L
45° Miter and 45° Bevel .............................................. 2-1/2 in. x 8-3/4 in.
3
2007/12
Download from Www.Somanuals.com. All Manuals Search And Download.
SYMBOLS
WARNING ICONS
Your power tool and its Owner’s Manual may contain “WARNING ICONS”
(a picture symbol intended to alert you to, and/or instruct you how to avoid,
a potentially hazardous condition). Understanding and heeding these
symbols will help you operate your tool better and safer. Shown below are
some of the symbols you may see.
SAFETY ALERT: Precautions that involve your safety.
PROHIBITION
WEAR EYE PROTECTION: Always wear safety goggles or safety
glasses with side shields.
READ AND UNDERSTAND INSTRUCTION MANUAL: To reduce
the risk of injury, user and all bystanders must read and understand
instruction manual before using this product.
KEEP HANDS AWAY FROM BLADE: Failure to keep your hands away
from the blade will result in serious personal injury.
SUPPORT AND CLAMP WORK
DANGER: indicates an imminently hazardous situation
which, if not avoided, will result in death or serious injury.
! DANGER
ꢀ
WARNING: indicates a potentially hazardous situation
which, if not avoided, could result in death or serious injury.
! WARNING
ꢀ
CAUTION: indicates a potentially hazardous situation which,
if not avoided, may result in minor or moderate injury.
! CAUTION
ꢀ
CAUTION: used without the safety alert symbol indicates
CAUTION
a potentially hazardous situation which, if not avoided,
may result in property damage.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
POWER TOOL SAFETY
GENERAL SAFETY INSTRUCTIONS
BEFORE USING THIS POWER TOOL
6. KEEP CHILDREN AWAY. All
visitors and bystanders should be
kept a safe distance from work area.
Safety is a combination of common
sense, staying alert and knowing how
to use your power tool.
7. MAKE WORKSHOP CHILD PROOF
with padlocks, master switches or by
removing starter keys.
CAUTION
8. DO NOT FORCE THE TOOL. It will
do the job better and safer at the
rate for which it was designed.
To avoid mistakes that could cause
serious injury, do not plug the tool in
until you have read and understood
the following.
9. USE THE RIGHT TOOL. Do not
force the tool or an attachment to do
a job for which it was not designed.
1.
READ and become familiar
with the entire Operator’s
Manual. LEARN the tool’s
application, limitations and
possible hazards.
10.USE PROPER EXTENSION
CORDS. Make sure your extension
cord is in good condition. When
using an extension cord, be sure to
use one heavy enough to carry the
current your product will draw. An
undersized cord will result in a drop
in line voltage and in loss of power
which will cause the tool to overheat.
The table on page 11 shows the
correct size to use depending on
cord length and nameplate ampere
rating. If in doubt, use the next
2. KEEP GUARDS IN PLACE and in
working order.
3. REMOVE ADJUSTING KEYS
AND WRENCHES. Form the habit
of checking to see that keys and
adjusting wrenches are removed
from the tool before turning ON.
4. KEEP WORK AREA CLEAN.
Cluttered areas and benches invite
accidents.
heavier gauge. The smaller the
gauge number, the heavier the cord.
11.WEAR PROPER APPAREL. Do
not wear loose clothing, gloves,
neckties, rings, bracelets or other
jewelry which may get caught in
moving parts. Nonslip footwear is
recommended. Wear protective hair
covering to contain long hair.
5. DO NOT USE IN DANGEROUS
ENVIRONMENTS. Do not use
power tools in damp locations, or
expose them to rain or snow. Keep
work area well lit.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
POWER TOOL SAFETY
17.USE RECOMMENDED
12.ALWAYS WEAR EYE
PROTECTION. Any power
ACCESSORIES. Consult
tool can throw foreign
this Operator’s Manual for
objects into the eyes and
could cause permanent
recommended accessories. The use
of improper accessories may cause
risk of injury to yourself or others.
eye damage. ALWAYS wear Safety
Goggles (not glasses) that comply
with ANSI Safety standard Z87.1.
Everyday eyeglasses have only
impact–resistant lenses. They
ARE NOT safety glasses. Safety
Goggles are available at Sears.
NOTE: Glasses or goggles not in
compliance with ANSI Z87.1 could
seriously injure you when they break.
18.NEVER STAND ON THE TOOL.
Serious injury could occur if the
tool is tipped or if the cutting tool is
unintentionally contacted.
19.CHECK FOR DAMAGED PARTS.
Before further use of the tool, a
guard or other part that is damaged
should be carefully checked to
determine that it will operate
13.WEAR A FACE MASK OR DUST
MASK. Sawing operation produces
dust.
properly and perform its intended
function – check for alignment of
moving parts, binding of moving
parts, breakage of parts, mounting
and any other conditions that may
affect its operation. A guard or other
part that is damaged should be
properly repaired or replaced.
14.SECURE WORK. Use clamps or
a vise to hold work when
practical. It is safer than
using your hand and
it frees both hands to
operate the tool.
20. NEVER LEAVE THE TOOL
RUNNING UNATTENDED. TURN
THE POWER “OFF”. Do not walk
away from a running tool until the
blade comes to a complete stop
and the tool is unplugged from the
power source.
15.DISCONNECT TOOLS FROM
POWER SOURCE before servicing,
and when changing accessories
such as blades, bits and cutters.
16.REDUCE THE RISK OF
UNINTENTIONAL STARTING.
Make sure switch is in the OFF
position before plugging the tool in.
21.DO NOT OVERREACH. Keep
proper footing and balance at all
times.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
POWER TOOL SAFETY
22. MAINTAIN TOOLS WITH CARE.
Keep tools sharp and clean for best
and safest performance. Follow
instructions for lubricating and
changing accessories.
23. WARNING: Dust generated from
certain materials can be hazardous
to your health. Always operate saw
in well-ventilated area and provide
for proper dust removal.
24.
! DANGER
ꢀ
People
with electronic devices, such as
pacemakers, should consult their
physician(s) before using this
product. Operation of electrical
equipment in close proximity to
a heart pacemaker could cause
interference or failure of the
pacemaker.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPOUND MITER SAW SAFETY
SPECIFIC SAFETY INSTRUCTIONS
FOR THIS COMPOUND MITER SAW
10.USE only blade collars specified for
your saw.
1. DO NOT operate the miter saw
until it is completely assembled
and installed according to these
instructions.
11.NEVER use blades larger in
diameter than 12 inches.
12.NEVER apply lubricants to the
blade when it is running.
2. IF YOU ARE NOT thoroughly
familiar with the operation of miter
saws, seek guidance from your
supervisor, instructor or other
qualified person.
13.ALWAYS check the blade for
cracks or damage before operation.
Replace a cracked or damaged
blade immediately.
14.NEVER use blades recommended
for operation at less than 4200
RPM.
3. ALWAYS hold the work firmly
against the fence and table.
DO NOT perform any operation
free hand (use clamp wherever
possible).
15.ALWAYS keep the blade guards in
place and use at all times.
16.NEVER reach around the saw
4. KEEP HANDS out of the path of the
saw blade. If the workpiece you are
cutting would cause your hands to
be within 8-3/4 in. of the saw blade,
the workpiece should be clamped in
place before making the cut.
blade.
17.MAKE SURE the blade is not
contacting the workpiece before the
switch is turned ON.
18.IMPORTANT: After completing the
cut, release the trigger and wait for
the blade to stop before returning
the saw to the raised position.
5. BE SURE the blade is sharp, runs
freely and is free of vibration.
6. ALLOW the motor to come up to full
speed before starting a cut.
19.MAKE SURE the blade has come
to a complete stop before removing
or securing the workpiece, changing
the workpiece angle or changing the
angle of the blade.
7. KEEP THE MOTOR AIR SLOTS
CLEAN and free of chips or dust.
8. ALWAYS MAKE SURE all handles
are tight before cutting, even if the
table is positioned in one of the
positive stops.
20. NEVER cut metals or masonry
products with this tool. This miter
saw is designed for use on wood
and wood-like products.
9. BE SURE both the blade and the
collar are clean and the arbor bolt is
tightened securely.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
21.NEVER cut small pieces. If the
workpiece being cut would cause
your hand or fingers to be within
8-3/4 in. of the saw blade the
workpiece is too small.
ELECTRICAL REQUIREMENTS
POWER SUPPLY AND MOTOR
SPECIFICATIONS
The AC motor used in this saw is
a universal, nonreversible type.
See “MOTOR” in the “PRODUCT
SPECIFICATIONS” section on page 2.
22.PROVIDE adequate support to the
sides of the saw table for long work
pieces.
23.NEVER use the miter saw in an
area with flammable liquids or
gases.
WARNING
!
To avoid electrical hazards, fire
hazards, or damage to the tool,
use proper circuit protection. Your
saw is wired at the factory for 120
V operation. Connect to a 120 V, 15
A circuit and use a 15 A time delay
fuse or circuit breaker. To avoid
shock or fire, if power cord is worn
or cut, or damaged in any way, have
it replaced immediately.
24.NEVER use solvents to clean plastic
parts. Solvents could possibly
dissolve or otherwise damage the
material.
25.SHUT OFF the power before
servicing or adjusting the tool.
26.DISCONNECT the saw from
the power source and clean the
machine when finished using.
27.MAKE SURE the work area is clean
before leaving the machine.
28.SHOULD any part of your miter saw
be missing, damaged, or fail in any
way, or any electrical component
fail to perform properly, lock the
switch and remove the plug from
the power supply outlet. Replace
missing, damaged, or failed parts
before resuming operation.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRICAL REQUIREMENTS AND SAFETY
ELECTRICAL REQUIREMENTS –
cont’d
DOUBLE INSULATED
The power tool is double insulated to
provide a double thickness of insulation
between you and tool’s electrical
system. All exposed metal parts are
isolated from the internal metal motor
components with protecting insulation.
1. Use only identical replacement parts
when servicing a tool with double
insulation. Servicing should be
performed by a qualified technician.
2. Do not use power tools in wet or
damp locations or expose them to
rain or snow.
MOTOR SAFETY PROTECTION
IMPORTANT
Replacement parts – When servicing,
use only identical replacement parts.
To avoid motor damage, the motor
should be blown out or vacuumed
frequently to keep sawdust from
interfering with the motor ventilation.
1. Connect this saw to a 120 V circuit.
This circuit must not be less than a
#12 wire with a 20 A time lag fuse or
a #14 wire with a 15 A time lag fuse.
NOTE: When using an extension
cord on a circuit with a #14 wire, the
extension cord must not exceed 25
feet in length.
Polarized plugs – This saw has a plug
that looks like the one shown below:
2. If the motor will not start, release the
trigger switch immediately. UNPLUG
THE SAW. Check the saw blade to
make sure it turns freely. If the blade
is free, try to start the saw again. If
the motor still does not start, refer to
the TROUBLESHOOTING GUIDE.
3. If the tool suddenly stalls while
cutting wood, release the trigger
switch, unplug the tool and free the
blade from the wood. The saw may
now be started and the cut finished.
4. FUSES may “blow” or circuit
breakers may trip frequently if:
a. MOTOR is overloaded –
To reduce the risk of electrical shock,
this saw has a polarized plug (one
blade is wider than the other). This plug
will fit in a polarized outlet only one
way. If the plug does not fit fully in the
outlet, reverse the plug. If it still does
not fit, contact a qualified electrician to
install the proper outlet. Do not change
the plug in any way.
WARNING
!
Double insulation does not take the
place of normal safety precautions
when operating this tool.
To avoid electrocution:
overloading can occur if you feed
10
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRICAL REQUIREMENTS AND SAFETY
too rapidly or make too many
start/stops in a short time.
b. LINE VOLTAGE is more
cord or have it repaired by a qualified
person before using it. Protect your
extension cords from sharp objects,
excessive heat and damp or wet areas.
Use a separate electrical circuit
for your tools. This circuit must not
be less than a #12 wire with a 20 A
time lag fuse or a #14 wire with a 15
A time lag fuse. NOTE: When using
an extension cord on a circuit with
a #14 wire, the extension cord must
not exceed 25 feet in length. Before
connecting the tool to the power line,
make sure the switch is in the OFF
position and the electric current is
rated the same as the current stamped
on the motor nameplate, running at a
lower voltage will damage the motor.
than 10% above or below the
nameplate voltage rating. For
heavy loads, the voltage at motor
terminals must equal the voltage
specified on the nameplate.
c. IMPROPER or dull saw blades
are used.
5. Most motor troubles may be traced
to loose or incorrect connections,
overload, low voltage or inadequate
power supply wiring. Always check
the connections, the load and supply
circuit if the motor doesn’t run well.
Check minimum gauge for the length
of cord you are using on the chart
below.
GUIDELINES FOR EXTENSION
CORDS
MINIMUM GAUGE FOR EXTENSION CORDS (AWG)
(When using 120 volts only)
Use a proper extension cord. Make
sure your extension cord is in good
condition. When using an extension
cord, be sure to use one heavy enough
to carry the current your product will
draw. An undersized cord will cause
a drop in line voltage, resulting in
loss of power and overheating. The
table below shows the correct size
to use depending on cord length and
nameplate ampere rating. If in doubt,
use the next heavier gauge. The
smaller the gauge number, the heavier
the cord.
Ampere Rating
Total length of Cord
More Than
Not More Than 25ft. 50ft. 100ft. 150ft.
0
6
18
18
16
14
16
16
16
16
14
14
14
12
12
6
10
12
16
10
12
12 Not Recommended
CAUTION: In all cases make certain
the receptacle in question is
properly grounded. If you are not
sure, have a certified electrician check the
receptacle.
Be sure your extension cord is
properly wired and in good condition.
Always replace a damaged extension
11
Download from Www.Somanuals.com. All Manuals Search And Download.
ACCESSORIES AND ATTACHMENTS
RECOMMENDED ACCESSORIES
WARNING
!
Read warnings and conditions on
your CARBIDE TIPPED SAW BLADE.
Do not operate the saw without the
proper saw blade guard in place.
Carbide is a very hard but brittle
material. Care should be taken while
mounting, using, and storing carbide
tipped blades to prevent accidental
damage. Slight shocks, such as
striking the tip while handling, can
seriously damage the blade. Foreign
objects in the workpiece, such as
wire or nails, can also cause tips
to crack or break off. Before using,
always visually examine the blade
and tips for bent blade, cracks,
breakage, missing or loose tips, or
other damage. Do not use if damage
is suspected. Failure to heed safety
instructions and warnings can result
in serious bodily injury.
WARNING
!
● Use only accessories
recommended for this miter
saw. Follow instructions that
accompany accessories. Use of
improper accessories may cause
hazards.
● The use of any cutting tool
except 12 in. saw blades which
meet the requirements under
recommended accessories
is prohibited. Do not use
accessories such as shaper
cutters or dado sets. Ferrous
metal cutting and the use of
abrasive wheels is prohibited.
● Do not attempt to modify this
tool or create accessories not
recommended for use with this
tool. Any such alteration or
modification is misuse and could
result in a hazardous condition
leading to possible serious injury.
ACCESSORIES
Visit your Sears Hardware Department
or see the Sears Power and Hand Tool
Catalog to purchase recommended
accessories for this power tool.
WARNING
!
To avoid the risk of personal injury,
do not modify this power tool or use
accessories not recommended by
Sears.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
TOOLS NEEDED FOR ASSEMBLY
Not supplied
Supplied
Adjustable Wrench
Hex Key
Blade Wrench
Combination Square
Phillips Screwdriver
Slotted Screwdriver
COMBINATION SQUARE MUST BE
TRUE
Should not gap or overlap when square
is flipped over (see dotted figure).
Straight edge or a 3/4 in.
board, this edge must be
perfectly straight.
Draw light line
on board along
this edge.
Should not gap or overlap
when square flipped over
(see dotted figure).
13
Download from Www.Somanuals.com. All Manuals Search And Download.
CARTON CONTENTS
2. Place the saw on a secure
UNPACKING YOUR MITER SAW
stationary work surface.
3. Separate all parts from the packing
material. Check each one with the
illustration to make certain all items
are accounted for, before discarding
any packing material.
WARNING
!
To avoid injury from unexpected
starting or electrical shock, do not
plug the power cord into a source
of power during unpacking and
assembly. This cord must remain
unplugged whenever you are
working on the saw.
WARNING
!
If any part is missing or damaged,
do not attempt to assemble the
miter saw, or plug in the power cord
until the missing or damaged part is
correctly replaced. To avoid electric
shock, use only identical replacement
parts when servicing double insulated
tools. Call 1-800-4-MY-HOME® for
replacement parts.
1. Remove the miter saw from the
carton.
IMPORTANT: Do not lift miter saw
by the trigger switch handle. It may
cause misalignment. Lift machine
by the built-in carry handle.
Miter Saw
Miter Handle
Blade Wrench
Dust Bag
Hold-down Clamp
14
Download from Www.Somanuals.com. All Manuals Search And Download.
KNOW YOUR SLIDING MITER SAW
Switch Handle
Dust Bag
Lower Blade Guard
Carrying Handle
Blade
Bevel Detent Pin
Hold-down Clamp
Laser Guide
Table Insert
Sliding Fence
Miter Handle
Positive Stop Locking Lever
Base
Table
Left Table Extension
Mounting Hole
Stop Latch Knob
Carrying Handle
Slide Carriage
Lock Knob
Laser ON/OFF
Switch
Right Extension Table
ON/OFF Trigger
Switch
Extension Table
Lock Knob
Motor
Stop Plate
Positive Miter Detents
15
Download from Www.Somanuals.com. All Manuals Search And Download.
GLOSSARY OF TERMS
AMPERAGE (AMPS) – A measure
requirements of ANSI Z.87.1 (USA) or
of the flow of electric current. Higher
ratings generally means the tool is
suited for heavier use.
CSA Z94.3-M88 (Canada).
FACE SHIELD – An impact resistant
shield that helps to protect your face
from chips, sparks, small debris.
Should only be used in conjunction with
additional eye protection.
ARBOR LOCK – Allows the user to
keep the blade from rotating while
tightening or loosening the arbor bolt
during blade replacement or removal.
FENCE – Helps to keep the workpiece
from moving when sawing. Scaled to
assist with accurate cutting.
BASE – Supports the table, holds
accessories and allows for workbench
or leg set mounting.
GUARD – Protective devise that forms
a barrier between a hazardous object
such as a blade, wheel or cutter and
the operator.
BEVEL LOCKING HANDLE – Locks
the miter saw at a desired bevel angle.
BEVEL SCALE – To measure the bevel
angle of the saw blade 0° to 45° left.
HOLD DOWN LATCH – Locks the
miter saw in the lowered position for
compact storage and transportation.
CARBIDE TIPPED – Extremely hard
steel pieces with sharp cutting edges
fastened to cutting tools such as saw
blades.
INSTRUCTION OR OWNER’S
MANUAL – Booklet accompanying
your power tool that describes the
hazards and safe operation procedures,
outlines basic tool operation, care and
maintenance.
COVER PLATE SCREW – Loosen this
screw and rotate the plate for access to
the blade arbor bolt.
DOUBLE-INSULATED – A form of
electrical protection featuring two
separate insulation systems to help
protect against electrical shock.
MITER HANDLE – Used to rotate the
table, and to rotate the saw to a right or
left cutting position.
MITER SCALE – Measures the miter
angle 0° to 45° left and right.
EXTENSION CORD – AN electric cord
used between power tools and outlets to
extend the range of the tools. The more
amerage your tool uses, the longer the
distance, the larger the size of the wire
needed in your extension cord.
MOUNTING HOLES – To mount the
miter saw to a stable surface.
ON/OFF TRIGGER SWITCH – To start
the tool, push the safety lock-off button
and squeeze the trigger. Release the
trigger to turn off the miter saw.
EYE PROTECTION – Googles or
spectacles intended to protect your
eyes. Eye protection should meet the
16
Download from Www.Somanuals.com. All Manuals Search And Download.
GLOSSARY OF TERMS
HEEL – Misalignment of the blade.
POSITIVE STOP LOCKING LEVER –
Locks the miter saw at a preset positive
stop for the desired miter angle.
KERF – The width of a saw cut,
determined by the thickness and set of
the blade.
SWITCH HANDLE – The switch handle
contains the trigger switch and safety
lock-off button. The blade is lowered
into the workpiece by pushing down
on the handle. The saw will return to
its upright position when the handle is
released.
KICKBACK – sudden and unintended
movement of the tool or workpiece. It is
typically caused by binding or pinching
of the workpiece
MITER CUT – A miter is a type of joint
where the two parts to be joined are cut
at an angle, and typically the finished
joint forms a 90-degree angle. Also
commonly spelled “miter”.
WARNING LABELS – Read and
understand for your own safety. Make
sure all labels are present on machine
and legible.
REVOLUTIONS PER MINUTE (RPM)
– The number of turns completed by a
spinning object in one minute.
WRENCH STORAGE – Convenient
storage to prevent misplacing the blade
wrench.
SAW BLADE PATH – The area of the
workpiece or table top directly in line
with the travel of the blade or the part
of the workpiece which will be cut.
WOODWORKING TERMS
ARBOR – The shaft on which a blade
is mounted.
SET – The distance between two saw
blade tips, bent outward in opposite
directions to each other. The further
apart the tips are, the greater the set.
BEVEL CUT – An angle cut made
through the face of the workpiece.
COMPOUND CUT – An angled cut
to both the edge and face of a board,
most common use is with crown
molding.
THIN-KERF BLADE – Thinner than
normal blades, remove less material,
smaller kerfs (between .065 and .070).
Blade thinness also may increase the
heat generated while cutting.
CROSS CUT – A cut which runs across
the board perpendicular to the grain.
FREEHAND – Performing a cut without
using a fence (guide), hold down or
other proper device to prevent the
workpiece from twisting during the
cutting operation.
WORKPIECE – The wood being
cut. The surfaces of a workpiece are
commonly referred to as faces, ends
and edges.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY AND ADJUSTMENTS
Estimated Assembly Time: 5 – 10
minutes
SAW BLADE WRENCH (FIG. C)
1. For convenient storage and
prevention of loss, there is a slot (1)
in the rear of the carrying handle
(2) for storing the blade wrench (3)
when not in use.
WARNING
!
To avoid injury, do not connect
this miter saw to the power source
until it is completely assembled and
adjusted and you have read and
understood this Operator’s Manual.
Fig. C
1
2
3
INSTALLING THE MITER HANDLE
(FIG. A)
1. Thread the miter handle (1) into the
hole located at the front of the miter
table.
Fig. A
RELEASING CUTTING HEAD (FIG. D)
Unlocking
WARNING
!
1
To avoid injury and damage to the
saw, transport and store the miter
saw with the cutting head locked in
the down position. Never use the stop
latch to hold the cutting head in a
down position for cutting operations.
UNLOCKING THE SLIDE CARRIAGE
(FIG. B)
After removing the saw from the carton,
loosen the slide carriage lock knob
(1). When transporting or storing the
miter saw, the slide carriage should
always be locked in position. The slide
carriage lock knob (1) is located on the
right side of the slide carriage.
1. Push down slightly on the switch
handle (1).
2. Pull out the stop latch knob (2).
3. Allow the cutting head to rise to the
up position.
Fig. D
Fig. B
1
2
1
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Locking
knob (3) to clamp the workpiece. Do
not use your other hand to hold the
clamp when tightening. Only turn
knob (3) to secure clamp to table.
The clamp will tilt at an angle and
secure itself when tightened.
When transporting or storing the miter
saw, the cutting head should always be
locked in the down position.
1. Push the cutting head down to its
lowest position.
2. Push the stop latch knob (2) into the
locking hole.
3
1
Fig. F
IMPORTANT: To avoid damage,
never carry the miter saw by the switch
handle, the cutting arm or the miter
handle. ALWAYS use the designated
carrying handles located on the top of
the machine and in the back of the unit.
2
INSTALLING THE EXHAUST PORT
AND THE DUST BAG (FIG. E)
1. Squeeze the metal collar wings (2) of
the dust bag (1).
Fig. G
2
2
2. Place the dust bag neck opening
around the exhaust port (3), and
release the metal collar wings.
Fig. E
1
3
2
REMOVING AND INSTALLING THE
TABLE INSERT (FIG. H)
WARNING
!
To avoid injury:
To empty the dust bag, squeeze the
metal collar and remove from exhaust
port. Open zipper on underside of bag
and empty into waste container.
NOTE: Check frequently and empty
bag before it gets full.
● Always unplug the saw to avoid
accidental starting. Remove all small
pieces of material from the table
cavity before performing any cuts.
The table insert may be removed for
this purpose, but always reattach
the table insert prior to performing a
cutting operation.
● Do not start the sliding compound
miter saw without checking for
interference between the blade and
table insert. Damage could result to
the blade, table insert or turntable if
blade strike occurs during the cutting
operation.
INSTALLING THE HOLD-DOWN
CLAMP (FIG. F and G)
1. Place the hold-down clamp assembly
(1) in one of the mounting holes (2),
located behind the fence.
NOTE: There are no screws to
secure clamp. The clamp will secure
itself to the base when turning the
19
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Loosen the miter handle (1). Lift up
the positive stop locking lever (2)
and position the table to left 150.
Release the positive stop locking
lever and lock the miter handle.
2. The sliding fence (3) must be
extended to the left.
3. To remove, loosen and remove the
six screws (4) on the table inserts
(5) with a Phillips screwdriver and
remove the insert.
4. To install, reposition the table insert,
install the six screws and tighten.
5. Check for blade clearance by moving
the slide carriage through the full
motion of the blade in the table slot.
handles located on the top of the
machine. When lifting, bend at
your knees, not from your back.
● Never carry the miter saw by
the power cord or by the switch
handle. Carrying the tool by the
power cord could cause damage
to the insulation or the wire
connections resulting in electric
shock or fire.
● To avoid injury from flying debris,
do not allow visitors to stand
near the saw during any cutting
operation.
● Support the saw on a level work
surface.
● Bolt or clamp the saw to its
support.
Fig. H
4
Mounting instructions
1. For stationary use, place the saw
in the desired location, directly on a
workbench where there is room for
handling and proper support of the
workpiece. The base of the saw has
four mounting holes. Bolt the base of
the miter saw (1) to the work surface
(5), using the fastening method as
shown in Fig I.
3
5
1
2
MOUNTING THE MITER SAW (FIG. I, J)
WARNING
!
To avoid injury form unexpected
saw movement:
● Disconnect the power cord from
the outlet, and lock the cutting
head in the lower position using
the stop latch.
● Lock the slide carriage in place by
tightening the slide carriage lock
knob.
Fig. I
1. Miter saw base
2. Hex head bolt
3. Rubber washer
4. Flat washer
2
3
4
1
5. Workbench
5
6. Flat washer
7. Lockwasher
8. Hex nut
6
7
8
9
● To avoid back injury, lift the saw
9. Jam nut
by using the designated carrying
20
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE: Mounting hardware is not
included with this tool. Bolts, nuts,
washers and screws must be
purchased separately.
4. While holding the lower blade guard,
loosen the cover plate screw (2) with
a Phillips screwdriver. (Fig. K)
5. Rotate the cover plate (3) to expose
the arbor bolt (4). (Fig. K)
2.
For portable use, place the
saw on a 3/4 in. thick piece
6. Place the blade end wrench over
the arbor bolt.
of plywood. Bolt the base
of the miter saw securely to the
plywood using the mounting holes on
the base. Use C-clamps to clamp
this mounting board to a stable work
surface at the worksite.
Fig. K
2
1
3
4
Fig. J
7. Locate the arbor lock (5) on the
motor. (Fig. L)
8. Press the arbor lock, holding it
in firmly while turning the blade
clockwise. The arbor lock will then
engage and lock the arbor. Continue
to hold the arbor lock, while turning
the wrench clockwise to loosen the
arbor bolt.
REMOVING OR INSTALLING THE
BLADE
Fig. L
Removing Blade (Fig. K, L and M)
WARNING
!
5
● To avoid injury from an accidental
start, make sure the switch is in
the OFF position and plug is not
connected to the power source
outlet.
9. Remove the arbor bolt (4), the arbor
collar (6), and the blade (7). Do not
remove the inner blade collar.
(Fig. M)
10.Raise the lower clear plastic blade
guard (1) to the upright position
(Fig. K) to remove the blade.
● Only use a 12-inch diameter blade.
1. Unplug the saw from the outlet
2. Raise the miter saw to the upright
position.
3. Raise the lower clear plastic blade
guard (1) to the uppermost position.
(Fig. K)
21
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE: Pay attention to the pieces
removed, noting their position and
direction they face. Wipe the blade
collars clean of any sawdust before
installing a new blade. Also, the 12 in.
blade has a 1 in. arbor hole with a 5/8
in. reducer (8) to mount onto the saw.
4. Press the arbor lock (5), holding
it in firmly while turning the blade
counterclockwise. When it engages,
continue to press the arbor lock
in, while tightening the arbor bolt
securely. (Fig. L)
5. Rotate the cover plate (3) back to its
original position until the slot in the
cover plate engages with the cover
plate screw (2). While holding the
lower blade guard, tighten the screw
with a Phillips screwdriver. (Fig. K)
NOTE: The lower blade guard must
be raised to the upright position to
access the cover plate screw.
6. Lower the clear retractable blade
guard (1) and verify the operation of
the guard does not bind or stick
(Fig. K).
Fig. M
7
8
6
4
INSTALLING BLADE (FIG. K, L, M)
WARNING
!
7. Be sure the arbor lock is released
so the blade turns freely by spinning
the blade until the arbor lock
Un-plug the miter saw before
changing/installing the blade.
1. Install a 12 in. blade with a 5/8 in.
arbor (or a 1 in. arbor with a 5/8 in.
reducer) making sure the rotation
arrow on the blade matches the
clockwise rotation arrow on the
upper guard, and the blade teeth
are pointing downward.
2. Place the arbor collar (6) against
the blade and on the arbor. Thread
the arbor bolt (4) on the arbor (Fig.
M) in a counterclockwise direction.
IMPORTANT: Make sure the flats of
the blade collars are engaged with
the flats on the arbor shaft. Also, the
flat-side of the arbor collar must be
placed against the blade.
disengages.
WARNING
!
● To avoid injury, never use the
saw without the cover plate
secure in place. It keeps the
arbor bolt from falling out if it
accidentally loosens, and helps
prevent the spinning blade from
coming off the saw.
● Make sure the collars are clean
and properly arranged. Lower the
blade into the table and check for
any contact with the metal base
or the turn table.
3. Place the blade wrench on the arbor
bolt.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
THE LASER BEAM
● NOTE: All the adjustments for the
operation of this machine have
been completed at the factory.
Due to normal wear and use,
some occasional readjustments
may be necessary.
● CAUTION-Use of controls or
adjustments or performance of
procedures other than those
specified herein may result in
hazardous radiation exposure.
● CAUTION-The use of optical
instruments with this product will
increase eye hazard.
WARNING
!
For your own safety, never connect
the plug to power source outlet
until all the adjustment steps
are complete and you have read
and understood the safety and
operational instructions.
Your tool is equipped with the Laser
Trac® cutting
guide using Class II laser beam. The
laser beam will enable to preview the
saw blade path on the stock to be cut
before starting the miter saw. This laser
guide is powered by the transformed
alternating current supply directly
through the power lead. The saw must
be connected to the power source
and the laser on/off switch must be
turned on for the laser line to show.
● Do not attempt to repair or
disassemble the laser. If
unqualified persons attempt
to repair this laser product,
serious injury may result. Any
repair required on this laser
product should be performed
by authorized service center
personnel.
WARNING
!
● AVOID DIRECT EYE CONTACT
Laser radiated when laser guide
is turned on. Avoid direct eye
contact. Always un-plug the miter
saw from power source before
making any adjustments.
● Laser Warning Label: Max output
<1mW DIODE LASER: 630-670
nm, Complies with 21CFR 1040.10
and 1040. 11.
CLASS II LASER PRODUCT.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
BEVEL STOP ADJUSTMENT
90° Bevel Pointer Adjustment (Fig. O)
1. When the blade is exactly 90o (0o) to
the table, loosen the bevel indicator
screw (5) using a # 2 Phillips
screwdriver.
2. Adjust bevel indicator (6) to the
“0” mark on the bevel scale and
retighten the screw.
WARNING
!
To avoid injury from an accidental
start, make sure the switch is in the
OFF position and the plug is not
connected to the power source outlet.
90° (0°) Bevel adjustment (Fig. N)
1. Loosen bevel lock handle (1) and
tilt the cutting arm completely to the
right. Tighten the bevel lock handle.
2. Place a combination square (2) on
the miter table with the ruler against
the table and the heel of the square
against the saw blade.
Fig. O
5
6
3. If the blade is not 90o (0o) square
with the miter table (5), loosen the
bevel lock handle (1), tilt the cutting
head to the left, loosen the locknut
(4) on the bevel angle adjustment
bolt (3) and use a 10 mm wrench
to adjust the stop bolt (3) depth in
or out to increase or decrease the
bevel angle.
45o Bevel Adjustment (Fig. P)
1. Loosen the bevel lock handle (7)
and tilt the cutting head completely
to the left.
2. Using a combination square, check
to see if the blade angle is 45° to
the table.
4. Tilt the cutting arm to back to the
right at 90o (0o) bevel and recheck
for alignment.
5. Repeat steps 1 through 4 if further
adjustment is needed.
6. Tighten bevel lock handle (1) and
locknut (4) when alignment is
achieved.
3. If the blade is not at 45° to the miter
table, tilt the cutting arm to the right,
loosen the locknut (8) on the bevel
angle adjustment bolt (9) and use
a 10 mm wrench to adjust the stop
bolt (9) depth in or out to increase
or decrease the bevel angle.
4. Tilt the cutting arm to the left to 45°
bevel and recheck for alignment.
5. Repeat steps 1 through 4 until the
blade is at 45° to the miter table.
6. Tighten bevel lock handle (7) and
locknut (8) when alignment is
achieved.
3
1
4
Fig. N
5
2
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Fig. P
1. Unlock the miter table by turning the
miter handle (1) counterclockwise.
2. Move the turntable while lifting up
on the positive stop locking lever
(2) to align the indicator (3) to the
desired degree measurement.
3. If the desired angle is one of the
nine positive stops, release the
positive stop locking lever, making
sure the lever snaps into position,
and then secure by tightening the
miter handle.
4. If the miter angle desired is not one
of the nine positive stops, simply
lock the miter table into position
by turning the miter handle in the
clockwise direction.
10
12
9
7
11
8
33.9° Bevel Adjustment (Fig. P)
1. Push the bevel detent pin (10) in
toward the front of the unit.
2. Unlock the bevel lock handle and tilt
the cutting arm to the crown molding
positive stop at 33.9o.
3. Using a combination square, check
to see if the blade angle is 33.9o to
the table.
Fig. Q
4. If the blade is not at 33.9o to the
miter table, loosen locknut (11) and
use a 10 mm wrench to adjust the
bolt (12) in or out until the blade is
at 33.9o to the miter table.
1
5. Secure the locknut (11) into position
after alignment is achieved.
3
4
2
MITER ANGLE ADJUSTMENT
(FIG. Q)
MITER SCALE INDICATOR
ADJUSTMENT (FIG. Q)
The sliding compound miter saw scale
can be easily read, showing miter
angles from 0° to 45° to the left, and 0°
to 45° to the right. The miter saw table
has nine of the most common angle
setttings with positive stops at 0°, 15°,
22.5°, 31.6°, and 45°. These positive
stops position the blade at the desired
angle quickly and accurately. Follow
the process below for quickest and
most accurate adjustments.
1. Move the table to the 0° positive
stop.
2. Loosen the screw (4) that holds the
indicator with a Phillips screwdriver.
3. Adjust the indicator (3) to the 0°
mark and retighten screw.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUSTING FENCE SQUARENESS
(FIG. R)
1. Loosen the three fence locking bolts
2. While holding the upper arm in that
position, turn the stop knob (1) until
it touches the stop plate (2).
(1).
3. Recheck the blade depth by moving
the cutting head front to back
2. Lower the cutting arm and lock in
position.
3. Using a square (3), lay the heel of
the square against the blade and
the ruler against the fence (2) as
shown.
4. Adjust the fence 90° to the blade
and tighten the four fence locking
bolts.
through the full motion of a typical
cut along the control arm.
Fig. S
1
CAUTION: If the saw has not
been used recently, recheck
blade squareness to the fence
and readjust if needed.
2
5. After fence has been aligned, using
a scrap piece of wood, make a cut
at 90o then check squareness on
the piece. Readjust if necessary.
ADJUSTING CUTTING DEPTH
(FIG. S)
The maximum depth travel of the
cutting head was set at the factory.
Check to see that the blade does not
extend more than 1/4 in. below the
table insert, and does not touch the
control arm throat or any part of the
base or table. If the maximum depth
needs readjusting:
Fig. R
1
1 2
1. Loosen the stop knob (1) while
moving the cutting head down until
the blade extends just 1/4 in. below
the table insert.
3
2. Adjust the stop knob (1) to touch the
stop plate (2).
3. Recheck the blade depth by moving
the cutting head front to back
through the full motion of a cut
along the control arm. If the blade
touches the inside of the control
arm, readjust the setting.
SETTING CUTTING DEPTH (FIG. S)
The depth of cut can be preset for even
and repetitive shallow cuts.
1. Adjust the cutting head down (See
CUTTING HEAD section) until the
teeth of the blade are at the desired
depth.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
SLIDING THE REAR EXTENSION
SUPPORT BAR (FIG. T)
!
WARNING
To avoid possible personal injury
or damage to the miter saw due
to tipping, do not operate the saw
without the Rear Extension Support
Bar.
Loosen the two screws (1) and extend
the rear extension support bar (2) by
sliding it out to match position, tighten
the two screws.
Fig. T
1
2
27
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
SAFETY INSTRUCTIONS FOR BASIC
SAW OPERATION
adjustments, including set-up and
blade changes.
● Compare the direction of rotation
arrow on the guard to the direction
arrow on the blade. The blade teeth
should always point downward at the
front of the saw.
BEFORE USING THE MITER SAW
!
WARNING
To avoid mistakes that could cause
serious, permanent injury, do not
plug the tool in until the following
steps are completed:
● Completely assemble and
adjust the saw, following the
instructions. (ASSEMBLY AND
ADJUSTMENTS)
● Learn the use and function of the
ON/OFF switch, lock-off switch,
upper and lower blade guards, hold
down latch, bevel lock handle and
cover plate screws.
● Review and understand all safety
instructions and operating procedures
in this Operator’s Manual. (SAFETY
& OPERATIONS)
● Tighten the arbor bolt.
● Tighten the cover plate screw.
● Check for damaged parts. Check
for:
● Alignment of moving parts
● Damaged electric cords
● Binding of moving parts
● Mounting holes
● Function of arm return spring
and lower guard: Push the cutting
arm all the way down, then let it rise
until it stops. The lower guard should
fully close. Follow instructions in
TROUBLESHOOTING GUIDE for
adjustment if necessary.
● Other conditions that may affect the
way the miter saw works.
● Review the MAINTENANCE and
TROUBLESHOOTING GUIDE for
your miter saw.
● To avoid injury or possible death
from electrical shock:
● Keep all guards in place, in working
order and proper adjustment. If any
part of this miter saw is missing,
bent, damaged or broken in any
way, or any electrical parts don’t
work, turn the saw off and unplug it.
● Replace bent, damaged, missing or
defective parts before using the saw
again.
Make sure your fingers do not
touch the plug’s metal prongs
when plugging or unplugging
your miter saw. (ELECTRICAL
REQUIREMENTS AND SAFETY)
BEFORE EACH USE INSPECT YOUR
SAW.
● Disconnect the miter saw.
To avoid injury from accidental
starting, unplug the saw before any
● Maintain tools with care. Keep the
miter saw clean for best and safest
performance. Follow instructions for
lubricating. Do not put lubricants on
the blade while it is spinning.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
● Remove adjusting wrench from the
● Plan ahead to protect your eyes,
hands, face and ears.
tool before turning it on.
● To avoid injury from jams, slips,
or thrown pieces, use only
recommended accessories.
● Know your miter saw. Read and
understand the Operator’s Manual
and labels affixed to the tool. Learn
its application and limitations as well
as the specific potential hazards
peculiar to this tool. To avoid injury
from accidental contact with moving
parts, do not do layout, assembly, or
setup work on the miter saw while
any parts are moving.
RECOMMENDED ACCESSORIES
● Consult the ACCESSORIES and
ATTACHMENTS section of this
Operators Manual for recommended
accessories. Follow the instructions
that come with the accessory. The
use of improper accessories may
cause risk of injury to persons.
● Choose the correct 12 in. diameter
blade for the material and the type
of cutting you plan to do. Do not use
Thin Kerf blades.
● Avoid accidental starting, make sure
the trigger switch is disengaged
before plugging the miter saw into a
power outlet.
PLAN YOUR WORK
● Make sure the blade is sharp,
undamaged and properly aligned.
With the saw unplugged, push
the cutting arm all the way down.
Manually spin the blade and check
for clearance. Tilt the power-head to
a 45° bevel and repeat the test.
● Make sure the blade and arbor
collars are clean.
● Use the right tool. Don’t force a tool
or attachment to do a job it was not
designed to do. Use a different tool
for any workpiece that can’t be held
in a solidly braced, fixed position.
CAUTION: This machine is not
designed for cutting masonry,
masonry products, ferrous metals
(steel, iron, and iron-based metals.)
Use this miter saw to cut only
wood, wood-like products, or non-
ferrous metals. Other material may
shatter, bind the blade, or create
other dangers. Remove all nails that
may be in the workpiece to prevent
sparking that could cause a fire.
Remove dust bag when cutting non-
ferrous metals.
● Make sure all clamps and locks are
tight and there is no excessive play
in any parts.
KEEP YOUR WORK AREA CLEAN
Cluttered areas and benches invite
accidents.
!
WARNING
To avoid burns or other fire damage,
never use the miter saw near
flammable liquids, vapors, or gases.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
DRESS FOR SAFETY
Any power tool can throw
DO NOT OVER-REACH
Keep good footing and balance. Keep
your face and body to one side, out of
the line of a possible kickback. NEVER
stand in the line of the blade.
Never cut freehand:
● Brace your workpiece firmly against
the fence and table stop so it will not
rock or twist during the cut.
● Make sure there is no debris
between the workpiece and the table
or fence.
● Make sure there are no gaps
between the workpiece, fence and
table that will let the workpiece shift
after it is cut.
foreign objects into the eyes.
This can result in permanent
eye damage. Everyday
eyeglasses have only impact
resistant lenses and are not
safety glasses. Glasses or
goggles not in compliance with
ANSI Z87.1 could seriously
injure you when they break.
● Do not wear loose clothing, gloves,
neckties or jewelry (rings, watches).
They can get caught and draw you
into moving parts.
● Wear non-slip footwear.
● Tie back long hair.
● Keep the cut off piece free to move
sideways after it is cut off. Otherwise,
it could get wedged against the
blade and thrown violently.
● Only the workpiece should be on the
saws table.
● Secure work. Use clamps or a vise
to help hold the work when it’s
practical.
● Roll long sleeves above the elbow.
● Noise levels vary widely. To avoid
possible hearing damage, wear ear
plugs when using any miter saw.
● For dusty operations, wear a dust
mask along with safety goggles.
INSPECT YOUR WORKPIECE
Make sure there are no nails or foreign
objects in the part of the workpiece
being cut.
Plan your work to avoid small pieces
that may bind, or that are too small to
clamp and get a solid grasp on. Plan
the way you will grasp the workpiece
from start to finish. Avoid awkward
operations and hand positions. A
sudden slip could cause your fingers or
hand to move into the blade.
USE EXTRA CAUTION WITH LARGE
OR ODD SHAPED WORKPIECES.
● Use extra supports (tables,
sawhorses, blocks, etc.) for
workpieces large enough to tip.
● Never use another person as a
substitute for a table extension, or as
an additional support for a workpiece
that is longer or wider than the basic
miter saw table, or to help feed,
support, or pull the workpiece.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
● Do not use this saw to cut small
WHEN SAW IS RUNNING
pieces. If the workpiece being cut
would cause your hand or fingers
to be within 8-3/4 inches of the saw
blade the workpiece is too small.
Keep hands and fingers out of the
“no hands zone” area marked on the
saws table.
!
WARNING
Do not allow familiarity from
frequent use of your miter saw
to result in a careless mistake. A
careless fraction of a second is
enough to cause a severe injury.
Before cutting, if the saw makes an
unfamiliar noise or vibrates, stop
immediately. Turn the saw OFF.
Unplug the saw. Do not restart until
finding and correcting the problem.
● When cutting odd shaped
workpieces, plan your work so it
will not bind in the blade and cause
possible injury. Molding, for example,
must lie flat or be held by a fixture or
jig that will not let it move when cut.
● Properly support round material such
as dowel rods, or tubing, which have
a tendency to roll when cut, causing
the blade to “bite”.
!
WARNING
To avoid injury, follow all applicable
safety instructions, when cutting
non-ferrous metals:
● Use only saw blades specifically
recommended for non-ferrous metal
cutting.
● Do not cut metal workpieces
that must be hand held. Clamp
workpieces securely.
● Cut non-ferrous metals only if you
are under the supervision of an
experienced person and the dust
bag has been removed from the
saw.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
BODY AND HAND POSITION (FIG. U) Before freeing jammed material:
● Release trigger switch.
WARNING
!
● Wait for all moving parts to stop.
● Unplug the miter saw.
Never place hands near
the cutting area. Proper
positioning of your
Fig. U
body and hands when
operating the miter saw
will make cutting easier
and safer. Keep children
away. Keep all visitors
at a safe distance from
the miter saw. Make sure
bystanders are clear of
the saw and workpiece.
Don’t force the saw. It will
do the job better and safer
at its designed rate.
No-Hand Zone (1)
Starting a cut:
● Place hands at least 8-3/4 in. away
from the path of the blade – out of
the “no-hands zone” (1). (Fig. U)
● Hold workpiece firmly against the
fence to prevent movement toward
the blade.
● With the power switch OFF, bring
the saw blade down to the workpiece
to see the cutting path of the blade.
● Press in lock-off switch in trigger
switch handle.
8-3/4 in.
BASIC SAW OPERATIONS
8-3/4 in.
WARNING
!
For your convenience, your saw
has a blade brake. The brake is
not a safety device. Never rely on
it to replace the proper use of the
guard on your saw. If the blade
doesn’t stop within approximately
10 seconds, wait for the blade to
stop, unplug the saw and contact
customer service.
● Squeeze trigger switch to start saw.
● Lower blade into workpiece with a
firm downward motion.
Finishing a cut:
● Hold the cutting arm in the down
TURNING THE SAW ON (FIG. V)
Depress the trigger switch (1) to turn
on the miter saw started.
NOTE: Make the ON/OFF switch
childproof. Insert a padlock, or chain
with padlock, through the holes (2) in
the trigger switch, locking the tool’s
switch, preventing children and other
unqualified users from turning the
machine on.
position.
● Release trigger switch and wait
for all moving parts to stop before
moving your hands and raising the
cutting arm.
● If the blade doesn’t stop within
10 seconds, unplug the saw
and follow the instructions in
TROUBLESHOOTING GUIDE
section.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
The miter saw is equipped with an
automatic blade brake. When the
trigger switch is released, the electric
blade brake will stop the blade within
approximately 10 seconds.
NOTE: When transporting the saw,
always secure the sliding fence in
the collapsed position (toward the
saw blade).
Fig. W
Fig. V
2
1
1
2
SLIDING FENCE & REMOVE
SLIDING CARRIAGE SYSTEM
(FIG. X)
SLIDING FENCE (FIG. W)
Sliding Fence
WARNING
!
WARNING
!
To reduce the risk of injury, return
carriage to the full rear position after
each crosscut operation.
The sliding fence must be extended
to the left when making bevel cuts.
The sliding fences note three bevel
angles where the user must adjust
the fences to match the degree of
the bevel cut. Failure to extend the
sliding fence will not allow enough
space for the blade to pass through
which could result in serious injury.
At extreme miter or bevel angles
the saw blade may also contact the
fence.
1. For chop cutting operations on small
workpieces, slide the cutting head
assembly completely toward the rear
of the unit and tighten the carriage
lock knob (1).
2. To cut wide boards up to 12-1/4
in., the carriage lock knob must be
loosened to allow the cutting head to
slide freely.
1. Unlock the fence cam locking lever
(1) by pushing it toward the rear of
the machine.
Fig. X
2. Extend the fence (2) by sliding it out
to match the degree of the bevel cut.
Lock the fence cam locking lever
by pushing it IN toward the fence.
1
33
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE LEAVING THE SAW
● Never leave tool running
Fig. Y
unattended. Turn power OFF. Wait
for all moving parts to stop.
● Make workshop childproof. Lock the
shop. Disconnect master switches.
Store tool away from children and
other unqualified users.
WARNING
!
3
1
2
To avoid injury from materials being
thrown, always unplug the saw
to avoid accidental starting, and
remove small pieces of material
from the table cavity.
WARNING
!
The sliding fence must be extended
to the left when making bevel cuts.
The sliding fences note three bevel
angles where the user must adjust
the fences to match the degree of
the bevel cut. Failure to extend the
sliding fence will not allow enough
space for the blade to pass through
which could result in serious injury.
At extreme miter or bevel angles
the saw blade may also contact the
fence.
MITER CUT (FIG. Y)
1. When a miter cut is required, unlock
the miter table by turning the miter
handle (1) counterclockwise.
2. While holding the miter handle, lift
up on the positive stop locking lever
(2).
3. Rotate the miter table to the right or
left with the miter handle.
4. When the table is in the desired
position, as shown on the miter
scale (3), release the positive stop
locking lever and tighten the miter
handle. The table is now locked at
the desired angle. Positive stops are
provided at 0°, 15°, 22.5°, 31.6° and
45°.
BEVEL CUT (FIG. Z)
1. When a bevel cut is required, loosen
the bevel lock handle (1) by turning
it clockwise.
2. Tilt the cutting head to the desired
angle, as shown on the bevel scale
(2).
3. The blade can be positioned at any
angle, from a 90° straight cut (0
° on the scale) to a 45° left bevel.
Tighten the bevel lock handle (1)
to lock the cutting head in position.
Positive stops are provided at 0°,
33.9° and 45°.
IMPORTANT: Always tighten the
miter table lock handle before
performing every cutting operation.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Fig. Z
angle. Release the positive stop
locking lever and lock the miter
handle.
Fig. BB
2
1
NOTE: The saw comes with a 33.9°
crown molding stop.
1
33.9° BEVEL STOP FOR CROWN
MOLDING (FIG. AA)
3
2
1. Push the bevel detent stop pin (2) in
toward the front of the machine.
2. Loosen the bevel lock handle (1).
3. Rotate the cutting head until the
bevel detent pin stops the bevel
angle at 33.9° on the bevel scale.
4. Tighten the bevel lock handle before
making a cut.
SLIDE CUTTING WIDE BOARDS UP
TO 12-1/4 in. WIDE (FIG. CC)
WARNING
To avoid injury:
!
● Never pull the cutting head
assembly and spinning blade toward
you during the cut. The blade may
try to climb up on the top of the
workpiece, causing the cutting
assembly and spinning blade to kick
back, forcefully. The cutting head
assembly should be drawn back
completely then pushed forward
when sawing.
Fig. AA
2
1
● Let the blade reach full speed before
cutting. This will help reduce the risk
of a thrown workpiece.
COMPOUND CUT (FIG. BB)
A compound cut is the combination of
a miter and a bevel cut simultaneously.
1. Loosen the bevel lock handle (1)
and position the cutting head at the
desired bevel position. Lock the
bevel lock handle.
2. Loosen the miter handle (2). Lift up
the positive stop locking lever (3)
and position the table at the desired
To Slide Cut Wide Boards (Fig. CC)
1. Unlock the carriage lock handle (1)
and allow the cutting head assembly
to move freely.
2. Set both the desired bevel angle
and/or the miter angle and lock into
position.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Use a hold down clamp to secure
the workpiece.
4. Grasp the switch handle (2) and pull
the carriage (3) forward until the
center of the saw blade is over the
front of the workpiece (4).
one stop plate at a time. Loosen the
locking screw (6), rotate the stop
plate (7) to vertical position and
retighten the locking bolt.
Fig. DD
5. Engage the trigger to turn the saw
on.
7
6
6. When the saw reaches full speed,
push the switch handle down,
slowly, cutting through the leading
edge of the workpiece.
7. Slowly move the switch handle
toward the fence, completing the cut.
8. Release the trigger and allow
the blade to stop spinning before
allowing the cutting head to raise.
5
CUTTING BOWED MATERIAL (FIG.
EE)
A bowed workpiece must be positioned
against the fence and secured with
a clamping devise before cutting as
shown. Do not position workpiece
incorrectly or try to cut the workpiece
without the support of the fence. This
will cause the blade to bind and could
result in personal injury.
Fig. CC
3
1
2
Fig. EE
4
WORKPIECE SUPPORT AND
REPETITIVE CUTTING USING THE
STOP PLATE (FIG. DD)
Long pieces need extension table
support.
1. Loosen the knob (5) then slide the
extension table to desired position
and tighten the knob.
2. The stop plate is designed for use
during repetitive cutting. Only use
36
Download from Www.Somanuals.com. All Manuals Search And Download.
AUXILIARY WOOD FENCE (FIG. FF)
CUTTING BASE MOLDING (FIG. GG)
When making multiple or repetitive cuts Base moldings and many other
that result in cut-off pieces of one inch
or less, it is possible for the saw blade
to catch the cut-off piece and throw it
out of the saw or into the blade guard
and housing, possibly causing damage
or injury. To minimize this, an auxiliary
wood fence can be mounted to your
saw.
moldings can be cut on a compound
miter saw. The setup of the saw
depends on molding characteristics
and application, as shown. Perform
practice cuts on scrap material to
achieve best results:
1. Always make sure moldings rest
firmly against fence and table. Use
hold-down, crown molding vise
or C-clamps, whenever possible,
and place tape on the area being
clamped to avoid marks.
2. Reduce splintering by taping the cut
area prior to making the cut. Mark
the cut line directly on the tape.
3. Splintering typically happens due to
an incorrect blade application and
thinness of the material.
Holes are provided in the saw fence
to attach an auxiliary wood fence. This
fence is to be constructed of straight
wood approximately 3/4 in. thick by
2-1/2 in. high by 18 in. long.
Attach the wood fence securely and
make a full depth cut to make a blade
slot.
Check for interference between the
wood fence and the lower blade guard.
Adjust if necessary.
Fig. GG
F
e
n
c
F
e
n
c
NOTE: This auxiliary fence is used
only with the saw blade in the 0° bevel
position (90° to the table). The auxiliary
wood fence must be removed when
bevel cutting.
e
e
Miter saw table
miter at 00, bevel at 450
Miter saw table
miter at 450, bevel at 00
NOTE: Always perform a dry run cut
so you can determine if the operation
being attempted is possible before
power is applied to the saw.
Fig. FF
Blade slot
37
Download from Www.Somanuals.com. All Manuals Search And Download.
CUTTING CROWN MOLDING
(FIG. HH, II)
Bevel/Miter Settings
Fig. II
Your compound miter saw is suited
for the difficult task of cutting crown
molding. To fit properly, crown molding
must be compound-mitered with
extreme accuracy. The two surfaces
on a piece of crown molding that fit
flat against the ceiling and wall are at
angles that, when added together,
equal exactly 90°.
Most crown molding has a top rear
angle (the section that fits flat against
the ceiling) of 52°and a bottom rear
angle (the section that fits flat against
the wall) of 38°.
Settings for standard crown molding
lying flat on compound miter saw
table
Inside corner
OR
OL
IR
IL
Outside corner
Compound cut crown moldings
NOTE: The chart below references
a compound cut for crown molding
ONLY WHEN THE ANGLE BETWEEN
THE WALLS EQUALS 90°.
In order to accurately cut crown
molding for a 90° inside or outside
corner, lay the molding with its broad
back surface flat on the saw table.
Bevel/Miter Settings
KEY BEVEL
SETTING SETTING
Inside corner-Left side
MITER
TYPE OF CUT
When setting the bevel and miter angles
for compound miters, remember that the
settings are interdependent; changing
one changes the other, as well.
33.9°
33.9°
33.9°
33.9°
31.6° Right
1. Position top of molding
against fence.
2. Miter table set at
RIGHT 31.6°.
3. LEFT side is finished
piece.
IL
Fig. HH
Inside corner-Right side
31.6° Left
1. Position bottom of
molding against fence.
2. Miter table set at LEFT
31.6°.
3. LEFT side is finished
piece.
IR
F
e
n
c
Outside corner-Left side
31.6° Left
1. Position bottom of
molding against fence.
2. Miter table set at LEFT
31.6°.
3. RIGHT side is finished
piece.
OL
OR
e
Miter saw table
Outside corner-Right side
31.6° Left
1. Position top of molding
against fence.
2. Miter table set at
RIGHT 31.6°.
3. RIGHT side is finished
piece.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
CROWN MOLDING CHART
Compound Miter saw
Miter and bevel Angle settings
Wall to Crown Molding Angle
52/38° Crown Molding
45/45° Crown Molding
52/38° Crown Molding
45/45° Crown Molding
Angle
Between
Walls
Angle
Between
Walls
Miter
Setting
Bevel
Setting
Miter
Setting
Bevel
Setting
Miter
Setting
Bevel
Setting
Miter
Setting
Bevel
Setting
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
42.93
42.39
41.85
41.32
40.79
40.28
39.76
39.25
38.74
38.24
37.74
37.24
36.75
36.27
35.79
35.31
34.83
34.36
33.90
33.43
32.97
32.52
32.07
31.62
31.17
30.73
30.30
29.86
29.43
29.00
28.58
28.16
27.74
27.32
26.91
26.50
26.09
25.69
25.29
24.89
24.49
24.10
23.71
23.32
22.93
22.55
22.17
21.79
21.42
21.04
20.67
20.30
19.93
19.57
19.20
18.84
18.48
41.08
40.79
40.50
40.20
39.90
39.61
39.30
39.00
38.69
38.39
38.08
37.76
37.45
37.13
36.81
36.49
36.17
35.85
35.52
35.19
34.86
34.53
34.20
33.86
33.53
33.19
32.86
32.51
32.17
31.82
31.48
31.13
30.78
30.43
30.08
29.73
29.38
29.02
28.67
28.31
27.96
27.59
27.23
26.87
26.51
26.15
25.78
25.42
25.05
24.68
24.31
23.94
23.57
23.20
22.83
22.46
22.09
46.89
46.35
45.81
45.28
44.75
44.22
43.70
43.18
42.66
42.15
41.64
41.13
40.62
40.12
39.62
39.13
38.63
38.14
37.66
37.17
36.69
36.21
35.74
35.26
34.79
34.33
33.86
33.40
32.94
32.48
32.02
31.58
31.13
30.68
30.24
29.80
29.36
28.92
28.48
28.05
27.62
27.19
26.77
26.34
25.92
25.50
25.08
24.66
24.25
23.84
23.43
23.02
22.61
22.21
21.80
21.40
21.00
36.13
35.89
35.64
35.40
35.15
34.89
34.64
35.38
34.12
33.86
33.60
33.33
33.07
32.80
32.53
32.25
31.98
31.70
31.42
31.34
30.86
30.57
30.29
30.00
29.71
29.42
29.13
28.83
28.54
28.24
27.94
27.64
27.34
27.03
26.73
26.42
26.12
25.81
25.50
25.19
24.87
24.56
24.24
23.93
23.61
23.29
22.97
22.66
22.33
22.01
21.68
21.36
21.03
20.70
20.38
20.05
19.72
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
18.13
17.77
17.42
17.06
16.71
16.37
16.02
15.67
15.33
14.99
14.66
14.30
13.97
13.63
13.30
12.96
12.63
12.30
11.97
11.64
11.31
10.99
10.66
10.34
10.01
9.69
9.37
9.05
8.73
8.41
8.09
7.77
7.46
7.14
6.82
6.51
6.20
5.88
5.57
5.26
4.95
4.63
21.71
21.34
20.96
20.59
20.21
19.83
19.45
19.07
18.69
18.31
17.93
17.55
17.17
16.79
16.40
16.02
15.64
15.25
14.87
14.48
14.09
13.71
13.32
12.93
12.54
12.16
11.77
11.38
10.99
10.60
10.21
9.82
9.43
9.04
8.65
8.26
7.86
7.47
7.08
6.69
6.30
5.90
5.51
5.12
4.72
4.33
3.94
3.54
20.61
20.21
19.81
19.42
19.03
18.64
18.25
17.86
17.48
17.09
16.71
16.32
15.94
15.56
15.19
14.81
14.43
14.06
13.68
13.31
12.94
12.57
12.20
11.83
11.46
11.09
10.73
10.36
10.00
9.63
9.27
8.91
8.55
8.19
7.83
7.47
7.11
6.75
6.39
6.03
5.68
5.32
4.96
4.61
4.25
3.90
19.39
19.06
18.72
18.39
18.06
17.72
17.39
17.05
16.71
16.38
16.04
15.70
15.36
15.02
14.62
14.34
14.00
13.65
13.31
12.97
12.62
12.29
11.93
11.59
11.24
10.89
10.55
10.20
9.85
9.50
9.15
8.80
8.45
8.10
7.75
7.40
7.05
6.70
6.35
6.00
5.65
5.30
4.94
4.59
4.24
4.32
4.01
3.70
3.39
3.08
2.77
2.47
2.15
1.85
1.54
1.23
0.92
0.62
0.31
3.89
3.53
3.10
2.83
2.47
2.12
1.77
1.41
3.54
3.19
2.83
2.48
2.12
1.77
1.41
1.06
3.15
2.75
2.36
1.97
1.58
1.18
0.79
0.39
1.06
0.71
0.35
0.71
0.35
39
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
MAINTENANCE
The ears on the metal end of the
assembly go in the same hole the
carbon part fits into. Tighten the cap
snugly, but do not overtighten.
WARNING
Never put lubricants on the blade
while it is spinning.
!
NOTE: When reinstalling the same
brushes, put them back in the way they
came out. This will avoid a break-in
period that reduces motor performance
and increases wear.
WARNING
!
● To avoid fire or toxic reaction,
never use gasoline, naphtha
acetone, lacquer thinner or similar
highly volatile solvents to clean
the miter saw.
Fig. JJ
● To avoid injury from unexpected
starting or electrical shock,
unplug the power cord before
working on the saw.
● For your safety, this saw is double
insulated. To avoid electrical
shock, fire or injury, use only
parts identical to those identified
in the parts list. Reassemble
exactly as the original assembly
to avoid electrical shock.
2
1
LOWER BLADE GUARD
Do not use the saw without the lower
blade guard. The lower blade guard is
attached to the saw for your protection.
Should the lower guard become
damaged, do not use the saw until the
damaged guard has been replaced.
Check regularly to make sure the lower
guard is working properly. Clean the
lower guard of any dust or buildup with
a damp cloth.
REPLACING CARBON BRUSHES
(FIG. JJ)
Replace both carbon brushes when
either has less than 1/4 in. length of
carbon remaining, or if the spring or
wire is damaged or burned. To inspect
or replace brushes, first unplug the
saw. Then remove the black plastic
cap (1) on the side of the motor (2).
Carefully remove the spring-loaded
cap. Then pull out the brush and
replace. Replace for the other side. To
reassemble, reverse the procedure.
WARNING
!
● Do not use solvents on the guard.
They could make the plastic
“cloudy” and brittle.
● When cleaning the lower guard,
unplug the saw from the power
source receptacle to avoid
unexpected start-up.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Link: (which actuates the lower guard
SAWDUST
movement) may be oiled at the rear
pivot, greased at ball bearing contact,
and oiled where the link actuates the
acetyl roller of the lower guard, if the
down chop motion is hard to start.
Periodically, sawdust will accumulate
under the worktable and base. This
could cause difficulty in the movement
of the worktable when setting up
a miter cut. Frequently blow out or
vacuum up the sawdust.
Fig. KK
WARNING
!
Link
If blowing sawdust, wear proper
eye protection to keep debris from
blowing into eyes.
Link
LUBRICATION (FIG. KK)
Chop pivot
All the motor bearings in this tool are
lubricated with a sufficient amount of
high-grade lubricant for the life of the
unit under normal operating conditions;
therefore, no further lubrication is
required.
Central pivot of
plastic guard
Lubricate the following as necessary:
Chop pivot: Apply light machine oil to
points indicated in illustration.
Central pivot of plastic guard: Use
light household oil (sewing machine
oil) on metal-to-metal or metal-to-
plastic guard contact areas as required
for smooth, quiet operation. Avoid
excessive oil, to which sawdust will
cling.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING GUIDE
!
WARNING
To avoid injury from accidental starting, always turn switch OFF and unplug
the tool before moving, replacing the blade or making adjustments.
TROUBLESHOOTING GUIDE - MOTOR
SUGGESTED CORRECTIVE
PROBLEM
PROBLEM CAUSE
ACTION
Brake does 1. Motor brushes not sealed 1. Inspect/clean/replace brushes.
not stop blade or lightly sticking.
See MAINTENANCE section.
2. Use a recommended blade. Let
cool down. See REMOVING
OR INSTALLING THE BLADE
section.
within 10
seconds.
2. Motor brake overheated
from use of defective or
wrong size blade or rapid
ON/OFF cycling.
3. Arbor bolt loose.
4. Brushes cracked,
damaged, etc.
3. Retighten. See REMOVING
OR INSTALLING THE BLADE
section.
5. Other.
4. Replace brushes.
5. Contact Sears Service Center.
Motor does 1. Limit switch failure
1. Replace limit switch.
2. Replace brushes. See
MAINTENANCE section.
3. Verify there is electrical power at
the outlet.
not start
2. Brush worn.
3. Fuse blown or circuit
breaker tripped on home
panel.
Brush spark 1. Brush worn.
when switch 2. Other.
released.
1. Replace Brushes. See
MAINTENANCE section.
2. Contact Sears Service Center.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING GUIDE
TROUBLESHOOTING GUIDE - SAW OPERATION
SUGGESTED CORRECTIVE
PROBLEM
PROBLEM CAUSE
ACTION
Blade hits
table.
1. Misalignment.
1. See ADJUSTMENT - Setting
Cutting Depth section.
Angle of cut 1. Miter table unlocked.
not accurate. 2. Sawdust under table.
Can not
1. See OPERATION - Miter Angle
Adjustment section.
2. Vacuum or blow out dust. WEAR
EYE PROTECTION.
adjust miter.
Cutting arm 1. Loose pivot points.
wobbles.
1. Contact Sears Service Center.
Cutting arm 1. Pivot spring not replaced 1. Contact Sears Service Center.
will not fully
raise, or
properly after service.
2. Sawdust build-up.
2. Clean and lubricate moving parts.
blade guard
won’t fully
close.
Blade binds, 1. Improper operation.
jams, burns 2. Dull or warped blade.
1. See BASIC SAW OPERATION
section.
wood.
3. Improper blade size.
2. Replace or sharpen blade.
4 Wood is moving during cut. 3. Replace with 12 in. diameter
blade.
4. Use hold down clamp to secure
workpiece to table.
Saw vibrates 1. Saw blade not round /
1. Replace blade.
or shakes.
damaged / loose.
2. Arbor bolt loose.
2. Tighten arbor bolt.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST
12 in. COMPOUND MITER SAW
MODEL NO. 137.212390
!
WARNING
When servicing use only CRAFTSMAN replacement parts. Use of any other parts many create
a HAZARD or cause product damage. Any attempt to repair or replace electrical parts on this
Miter Saw may create a HAZARD unless repair is done by a qualified service technician. Repair
service is available at your nearest Sears Service Center.
PARTS LIST FOR SAW SCHEMATIC A
I.D.
083Z
Description
CORD CLAMP
Size
QTY I.D.
Description
Size
# 06
QTY
1
1
1
1
1
1
4
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
2
1
1
2
2
1
2
1
1
1
1
2
1
4
1
2
1
2
2
1
2
4
1
1
4
1
1
2
1
2
1
1
2
1
1
2
1
1
262V ANCHOR PLATE
26LU WARNING LABEL
26P7 SHAFT-PIVOT
27AE COLLAR
290M CAUTION LABEL
2C1G SHAFT-PIVOT
2CGT SLOTTED SET SCREW
2D92 CONTROLLER ASS’Y
2DX9 SEGMENT HANDLE
2E63 ROCKER SWITCH
2EXC LOCATION PIN
091S COMPRESSION SPRING
0CKS SPRING WIRE
0CQH HOLD DOWN CLAMP ASS’Y
0DHT SPRING GUARD
0DTZ ARBOR COLLAR
0DVJ BLADE WRENCH
0F1H COLLAR
0J4D FLAT WASHER
0J4E
0J7G FLAT WASHER
0JB0 WAVE WASHER
0JE7
φ5*10-1
φ6*13-1
3/8*29/32-1/8
WW-8
FLAT WASHER
2F39
CLEVIS PIN
C-RING
2F8Y DUST BAG ASS’Y
2F9N STICKER
2GYC SHAFT SLEEVE
2K96 WARNING LABEL
2MGR POWER CABLE
2MN9 LASER PLUNGER HOUSING
2PWU MOTOR
0JMN O-RING
0JMP O-RING
0JXB HEX. SOC. SET SCREW
0JZF
M6*1.0-16
M6*1.0-10
M8*1.25-20
M5*0.8-30
M6*1.0-20
M4*0.7-10
M6*1.0-8
HEX. SOC. SET SCREW
0JZN ARBOR BOLT
0K2V HEX. SOC. HD.CAP SCREW
0K5D CR. RE. COUNT HD. SCREW
0K6Y CR. RE. TRUSS HD. SCREW
0K74 CR. RE. TRUSS HD. SCREW
0K7X
0K7Z
0KA9 CR. RE. PAN HD. TAPPING SCREW M3*24-10
0KB7 CR. RE. PAN HD. TAPPING SCREW M4*18-16
0KBD CR. RE. PAN HD. TAPPING SCREW M4*18-25
0KC6 CR. RE. TRUSS HD. TAPPING SCREW M4*16-12
0KD6 CR. RE. PAN HD. SCREW
0KDK CR. RE. PAN HD. SCREW
0KDM CR. RE. PAN HD. SCREW
0KDR CR. RE. PAN HD. SCREW
0KE0 CR. RE. PAN HD. SCREW
0KL1
0KMS HEX. NUT
0KR1 LOCK NUT
0KTQ CABLE CLAMP
0KUW TERMINAL
0LTQ TRIGGER SWITCH
0S1S
0XQ8 CR. RE. PAN HD. TAPPING SCREW M6*1.0-20
23LN KNOB-HANDLE
23NX GUARD-CORD
2PY1 ARM
# AW
# AW
2PYE DUST COLLECTOR
2PYG CUTTER SHAFT GUARD
2PYJ SHAFT-PIVOT
CR. RE. TRUSS HD. ROUND NECK SCREW
M6*1.0-10
M6*1.0-14
CR. RE. TRUSS HD. ROUND NECK SCREW
2PYK LEVER
2PYL MOTOR HANDLE (UP)
2PYM MOTOR HANDLE (DOWN)
2PYN CABLE SHIELD
2PYP NEEDLE POINTER
2Q19 LEAD WIRE ASS’Y
2Q1F LEAD WIRE ASS’Y
2Q2U TORSION SPRING
2Q41 PC-GUARD ASS’Y
2QBG CLAMP BOLT
2QU7 PLUNGER HOUSING ASS’Y
2QVY SWIVEL SUPPORT ASS’Y
2R2G TRADE-MARK LABEL
2R2M LABEL
# 23
M4*0.7-8
M5*0.8-16
M5*0.8-20
M5*0.8-10
M6*1.0-40
M6*1.0-12
M6*1.0 T=5
M16*2.0 T=16
CR. RE. PAN HD. ROUND NECK SCREW
2R2N TRADE-MARK LABEL
2R2Q CAUTION LABEL
2RAS FLAT WASHER
2RAU COMPRESSION SPRING
2RAV CLAMP BOLT
COLLAR
Φ16*38-3
2RCW BLADE
44
Download from Www.Somanuals.com. All Manuals Search And Download.
12 in. COMPOUND MITER SAW
SCHEMATIC A
MODEL NO. 137.212390
45
Download from Www.Somanuals.com. All Manuals Search And Download.
12 in. COMPOUND MITER SAW
MODEL NO. 137.212390
PARTS LIST FOR SAW SCHEMATIC B
I.D.
Description
CENTER BOLT
REAR EXTENTION STAY
FLAT WASHER
FLAT WASHER
Size
QTY
1
1
1
6
2
3
1
1
6
3
2
2
1
7
1
2
4
3
1
2
1
1
1
1
1
1
4
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
3
1
2
1
1
1
1
1
0DTH
0H9A
0J6A
0J74
0JAZ
0JPF
φ8*16-2.5
1/4*5/8-3/32
WW-6
M6*1.0-25
M6*1.0-16
M8*1.25-16
M6*1.0-16
M8*1.25-30
M6*1.0-8
M6*1.0-16
M5*0.8-10
M4*0.7-8
M5*0.8-40
M6*1.0-12
M6*1.0-16
M6*1.0 T=5
M5*0.8 T=5
M6*1.0 T=6
M8*1.25 T=8
WAVE WASHER
HEX. HD. BOLT
0JXB
0JXG
0K2B
0K2L
0K74
0K7L
0KAE
0KD6
0KDS
0KDU
0KDV
0KMS
0KQW
0KQX
0KR4
2258
2754
20S3
20X5
21EW
25TD
25TE
HEX. SOC. SET SCREW
HEX. SOC. SET SCREW
HEX. SOC. HD. CAP SCREW
HEX. SOC. HD. CAP SCREW
CR. RE. TRUSS HD. SCREW
CR. RE. ROUND WASHER HD. SCREW
CR. RE. PAN HD. TAPPING SCREW
CR. RE. PAN HD. SCREW
CR. RE. PAN HD. SCREW
CR. RE. PAN HD. SCREW
CR. RE. PAN HD. SCREW
HEX. NUT
LOCK NUT
NUT
LOCK NUT
SPECIAL BOLT
WARNING LABEL
LOCKING HANDLE ASS’Y
ASSIST-FENCE
CR. RE. PAN HD. TAPPING SCREW
MITER BAR
STOP BLOCK (LEFT)
STOP BLOCK (RIGHT)
TABLE INSERT
# AW
M5*12-35
# 23
# 23
25TF
27BU
27BV
2C8U
2CD2
2DWL
2DWP
2F76
TABLE INSERT
KNOB
COMPRESSION SPRING
PLUNGER HANDLE
NEEDLE POINTER
FENCE
WARNING LABEL
VISE ASS’Y
# 23
# AW
2K8Q
2LSZ
2PY0
2PY2
2PY7
2PY8
2PYB
2PYD
2PYH
2PYQ
2PYR
2QT8
2QXE
2QZX
2QZZ
2R2R
2R7W
BASE
TABLE
# AW
# AW
# AW
# AW
EXTENSION WING (LEFT)
EXTENSION WING (RIGHT)
SLIDE-BAR BLADE GUARD
SEGMENT HANDLE (REAR)
SET PLATE
SLIDE PLATE
SUPPORT
CR. RE. TRUSS HD. ROUND NECK SCREW
INSTRUCTION MANUAL
SCALE
M6*1.0-17
SCALE
TRADE-MARK LABEL
LOCKING HANDLE ASS’Y
46
Download from Www.Somanuals.com. All Manuals Search And Download.
12 in. COMPOUND MITER SAW
SCHEMATIC B
MODEL NO. 137.212390
47
Download from Www.Somanuals.com. All Manuals Search And Download.
12 in. COMPOUND MITER SAW
PARTS LIST FOR MOTOR
MODEL NO. 137.212390
I.D.
0JCF
0JX2
Description
SPRING PIN
Size
φ4-30
M5*0.8-6
M5*0.8-12
M5*12-60
M5*0.8-6
QTY
1
2
3
2
2
1
1
1
1
2
2
2
1
1
1
HEX. SOC SET SCREW
CR. RE. PAN HD. SCREW & WASHER
CR. RE. PAN HEAD TAPPING & WASHER SCREW
PLASTIC SCREW
FLOW GUIDE
COMPRESSION SPRING
RUBBER CAP
PROTECTOR WIRE
BRUSH HOLDER ASS’Y
BRUSH ASS’Y
BRUSH COVER
BEARING BUSHING
CLEVIS PIN
0K44
0KCP
0KLA
0Q9K
0QGR
0QMK
0QMY
0QQS
0QQT
0QR0
0QR2
21AX
23Z3
GEAR BOX
# AW
23Z4
MOTOR HOUSING
ARMATURE ASS’Y
CUTTER SHAFT ASS’Y
CR. RE. PAN HD. SCREW & WASHER
FIELD ASS’Y
1
1
1
4
240R
27DB
2B79
2PXT
M5*0.8-35
1
2Q0P
LEAD WIRE ASS’Y
1
48
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Get it fixed, at your home or ours!
Your Home
For expert troubleshooting and home solutions advice:
For repair – in your home – of all major brand appliances,
lawn and garden equipment, or heating and cooling systems,
no matter who made it, no matter who sold it!
For the replacement parts, accessories and
owner’s manuals that you need to do-it-yourself.
For Sears professional installation of home appliances
and items like garage door openers and water heaters.
1-800-4-MY-HOME® (1-800-469-4663)
Call anytime, day or night (U.S.A. and Canada)
Our Home
For repair of carry-in items like vacuums, lawn equipment,
and electronics, call anytime for the location of your nearest
Sears Parts & Repair Service Center
1-800-488-1222 (U.S.A.)
1-800-469-4663 (Canada)
To purchase a protection agreement on a product serviced by Sears:
1-800-827-6655 (U.S.A.)
1-800-361-6665 (Canada)
Para pedir servicio de reparación
a domicilio, y para ordenar piezas:
Au Canada pour service en français:
MC
1-800-LE-FOYER
1-888-SU-HOGAR®
(1-800-533-6937)
(1-888-784-6427)
® Registered Trademark / TM Trademark / SM Service Mark of Sears Brands, LLC
® Marca Registrada / TM Marca de Fábrica / SM Marca de Servicio de Sears Brands, LLC
MC Marque de commerce / MD Marque déposée de Sears Brands, LLC
© Sears Brands, LLC
Download from Www.Somanuals.com. All Manuals Search And Download.
|