Owner's Manual
®
7-in.
Buffer / Polisher
Model No.
172.107210
Double Insulated
WARRANTY
CAUTION: Read, understand and follow
all Safety Rules and Operating Instructions
in this manual before using this product.
•
SAFETY
•
•
•
•
•
•
UNPACKING
DESCRIPTION
OPERATION
MAINTENANCE
ACCESSORIES
Sears Brands Management Corporation,
Hoffman Estates, IL 60179 U.S.A.
3025736
7/11/12
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INSTRUCTIONS cont.
SAFETY INSTRUCTIONS
TOOL USE AND CARE SAFETY
!
WARNING: Read all safety warnings and instructions. Failure to
follow the warnings and instructions may result in electric shock, fire
and/or serious injury.
!
WARNING: BE SURE to read and understand all instructions before
operating this tool. Failure to follow all instructions listed below may result
in electric shock, fire and/or serious personal injury.
Save all warnings and instructions for future reference.
The term power tool in the warnings refers to your electric (corded)
power tool or battery-operated (cordless) power tool.
1. Do not force the power tool. Use the correct power tool for your application.
The correct power tool will do the job better and safer at the rate for which it was
designed.
2. Do not use the power tool if the switch does not turn it on and off. Any power
WORK AREA SAFETY
tool that cannot be controlled with the switch is dangerous and must be repaired.
1. Keep work area clean and well lit. Cluttered or dark areas invite accidents.
3. Disconnect the plug from the power source and/or the battery pack from the
power tool before making any adjustments, changing accessories, or storing
power tools. Such preventive safety measures reduce the risk of starting the
power tool accidentally.
2. Do not operate power tools in explosive atmospheres, such as in the presence
of flammable liquids, gases or dust. Power tools create sparks which may ignite
the dust or fumes.
4. Store idle power tools out of the reach of children and do not allow persons
unfamiliar with the power tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained users.
3. Keep children and bystanders away while operating a power tool. Distractions
can cause you to lose control.
4. Make your workshop childproof with padlocks and master switches. Lock
5. Maintain power tools. Check for misalignment or binding of moving parts,
breakage of parts and any other condition that may affect the power tools
operation. If damaged, have the power tool repaired before use. Many
accidents are caused by poorly maintained power tools.
tools away when not in use.
5. MAKE SURE the work area has ample lighting so you can see the work and that
there are no obstructions that will interfere with safe operation BEFORE using your
power tool.
6. Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp
cutting edges are less likely to bind and are easier to control.
PERSONAL SAFETY
7. Use the power tool, accessories and tool bits etc., in accordance with these
instructions and in the manner intended for the particular type of power tool,
taking into account the working conditions and the work to be performed.
Use of the power tool for operations different from those intended could result in a
hazardous situation.
1. Stay alert, watch what you are doing and use common sense when operating
a power tool. Do not use a power tool while you are tired or under the
influence of drugs, alcohol or medication. A moment of inattention while
operating power tools may result in serious personal injury.
8. Use clamps or another practical way to secure and support the workpiece to
2. Use personal protective equipment. Always wear eye protection. Protective
equipment such as dust mask, non-skid safety shoes, hard hat, or hearing
protection used for appropriate conditions will reduce personal injuries.
a stable platform.
9. Holding the work by hand or against your body leaves it unstable and may
lead to loss of control.
3. Prevent unintentional starting. Ensure the switch is in the off-position before
connecting to power source and/or battery pack, picking up or carrying the
tool. Carrying power tools with your finger on the switch or energizing power tools
that have the switch on invites accidents.
ELECTRICAL SAFETY
1. Double insulated tools are equipped
with a polarized plug (one blade is wider
than the other). This plug will fit in a
4. Remove any adjusting key or wrench before turning the power tool on.
A wrench or a key left attached to a rotating part of the power tool may result in
personal injury.
polarized outlet only one way. If the plug
does not fit fully in the outlet, reverse the plug.
If it still does not fit, contact a qualified
electrician to install a polarized outlet. Do
not change the plug in any way.
Cover of
Grounded
Outlet Box
5. Do not overreach. Keep proper footing and balance at all times. This enables
better control of the power tool in unexpected situations.
6. Dress properly. Do not wear loose clothing or jewelry. Keep your hair,
clothing and gloves away from moving parts. Loose clothes, jewelry or long hair
can be caught in moving parts.
!
WARNING: Do not permit fingers
7. If devices are provided for the connection of dust extraction and collection
facilities, ensure these are connected and properly used. Use of dust collection
can reduce dust-related hazards.
to touch the terminals of plug when
installing or removing the plug from
the outlet.
5
4
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INSTRUCTIONS cont.
SAFETY INSTRUCTIONS cont.
ELECTRICAL SAFETY cont.
SAFETY SYMBOLS FOR YOUR TOOL
2. Power tool plugs must match the outlet. Never modify the plug in any way.
Do not use any adapter plugs with grounded power tools. Unmodified plugs
and matching outlets will reduce risk of electric shock.
The label on your tool may include the following symbols.
V.......................................................................Volts
A......................................................................Amps
!
WARNING: Double insulation DOES NOT take the place of normal
Hz....................................................................Hertz
safety precautions when operating this tool.
W.....................................................................Watts
min..................................................................Minutes
3. Avoid body contact with grounded surfaces such as pipes, radiators, ranges
and refrigerators. There is an increased risk of electric shock if your body is
grounded.
....................................................................Alternating current
..................................................................Direct current
no ....................................................................No-load speed
....................................................................Class II construction, Double Insulated
RPM……………………….............................. .Revolutions per minute
SPM…...........................…………………….....Strokes per minute
OPM………………..........................………..... Orbits per minute
4. Do not expose power tools to rain or wet conditions. Water entering a power
tool will increase the risk of electric shock.
5. Do not abuse the cord. Never use the cord for carrying, pulling or unplugging
the power tool. Keep cord away from heat, oil, sharp edges or moving parts.
Damaged or entangled cords increase the risk of electric shock.
....................................................................Indicates danger, warning or caution.
It means attention! Your safety is involved.
!
6. When operating a power tool outdoors, use an extension cord suitable for
outdoor use marked “W-A” or “W”. Use of a cord suitable for outdoor use
reduces the risk of electric shock.
7. If operating a power tool in a damp location is unavoidable, use a Ground
Fault Circuit Interupter (GFCI) protected supply. Use of a GFCI reduces the
risk of electric shock.
SERVICE SAFETY
1. If any part of this tool is missing or should break, bend, or fail in any way;
or should any electrical component fail to perform properly: SHUT OFF the
power switch and remove the tool’s plug from the power source and have the
missing, damaged or failed parts replaced BEFORE resuming operation.
EXTENSION CORDS
USE PROPER EXTENSION CORD. Make sure your extension cord is in good
condition. When using an extension cord, be sure to use one heavy enough to carry
the current your product will draw. An undersized cord will cause a drop in line
voltage resulting in loss of power and overheating. Table 1 shows the correct size to
use depending on cord length and nameplate ampere rating. If in doubt, use the
next heavier gage. The smaller the gage number, the heavier the cord.
2. Have your power tool serviced by a qualified repair person using only
identical replacement parts. This will ensure that the safety of the power tool
is maintained.
3. If the replacement of the supply cord is necessary, this has to be done by the
manufacturer or his agent in order to avoid a safety hazard.
Table 1: Minimum Gage for Cord
Rating
Volts
120V
Total cord length (in feet)
50 100
AWG
SAFETY RULES FOR BUFFER / POLISHERS
Ampere
25
150
More Than Not More
Than
!
WARNING: USE OF ACCESSORIES THAT ARE NOT RECOMMENDED
FOR USE WITH THIS TOOL MAY CREATE A HAZARDOUS CONDITION.
0
6
6
18
18
16
14
16
16
16
12
16
14
1. Read, understand and follow all safety rules and user instructions in this manual
and all directions and warnings on polishes and waxes BEFORE using this
buffer / polisher.
2. Vehicle should be clean and dry before using your buffer polisher. Remove all road
tar, excess grease spots and bug stains.
10
12
16
14
14
12
12
10
12
Not recommended
3. ALWAYS make sure the vehicle’s surface is cool before washing and using the
!
CAUTION: Keep the extension cord clear of the working area.
buffer / polisher.
Position the cord so that it will not get caught on lumber, tools, parts of the
vehicle or other obstructions while you are working with a power tool.
4. When changing accessories, BE SURE that the switch is in the OFF position and
the cord is unplugged.
5. DO NOT apply wax directly on car.
!
WARNING: Check extension cords before each use. If damaged
replace immediately. Never use tool with a damaged cord since touching
the damaged area could cause electrical shock, resulting in serious injury.
7
6
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INSTRUCTIONS cont.
SAFETY INSTRUCTIONS cont.
SAFETY RULES FOR BUFFER / POLISHERS cont.
ADDITIONAL RULES FOR SAFE OPERATION
6. To avoid splashing wax, ALWAYS start and stop the buffer/polisher on or against
the surface to be polished.
!
WARNING: BE SURE to read and understand all instructions.
Failure to follow all instructions listed below may result in electric shock,
fire and/or serious personal injury.
7. After plugging in extension cord, loop extension cord over tool’s stub length plug.
Then wrap hook and loop strip around extension cord to secure it in place.
8. Place extension cord over your shoulder to keep it safely out of your way.
1. Inspect the sponge pad before use. Do not use chipped, cracked or otherwise
defective products.
9. DO NOT apply excessive pressure against the work surface with this tool. The
random orbital motion feature on this tool will perform better when less pressure
is applied. Applying excessive pressure will slow the random orbital motion and
reduce the effectiveness of the tool.
2. Ensure that the bonnets are fitted in accordance with the manufacturer's instructions.
3. Ensure that the bonnet is correctly mounted and tightened before use and run the
tool at no-load for 30 seconds in a safe position. Stop immediately if there is
considerable vibration or if other defects are detected. If this condition occurs, check
the machine to determine the cause.
10. To prolong the life of the pad on the buffer / polisher, ALWAYS store the
buffer / polisher with the pad face up.
11. DO NOT USE ABRASIVE COMPOUNDS WITH THIS TOOL.
12. DO NOT immerse any part of the buffer / polisher in liquid.
4. For cleaning, personal protective equipment such as gloves and apron should be worn.
5. The wheel continues to rotate after the tool is switched off. Only withdraw the sponge
pad when the pad has stopped moving.
6. Do not use the polisher as a fixed tool.
7. SAVE THESE INSTRUCTIONS. Refer to them frequently and use them to
instruct others who may use this tool. If someone borrows this tool, make
sure they have these instructions also.
!
WARNING: Some dust created by using power tools contains
chemicals known to the State of California to cause cancer and birth
defects or other reproductive harm. Some examples of these chemicals are:
• Lead from lead-based paints.
• Crystalline silica from bricks and cement and other masonryproducts.
• Arsenic and chromium, from chemically treated lumber.
Your risk from these exposures varies, depending upon how often you do
this type of work. To reduce your exposure to these chemicals:
• Work in a well-ventilated area.
• Work with approved safety equipment, such as those dust
masks that are specially designed to filter out microscopic particles.
Avoid prolonged contact with dust from power sanding, sawing, grinding,
drilling and other construction activities. Wear protective clothing and wash
exposed areas with soap and water. Allowing dust to get into your mouth,
eyes, or lay on the skin may promote absorption of harmful chemicals.
!
WARNING: Use of this tool can generate and/or disburse dust, which
may cause serious and permanent respiratory or other injury. Always use
NIOSH/OSHA approved respiratory protection appropriate for the dust
exposure. Direct particles away from face and body.
8
9
Download from Www.Somanuals.com. All Manuals Search And Download.
UNPACKING
DESCRIPTION
KNOW YOUR BUFFER / POLISHER
!
WARNING: Your tool should NEVER be connected to the power
source when you are assembling parts, making adjustments, installing or
removing bonnets, cleaning or when it is not in use. Disconnecting the tool
will prevent accidental starting, which could cause serious personal injury.
NOTE: Before attempting to use your buffer / polisher, familiarize yourself
with all of the operating features and safety requirements.
1. Remove the buffer / polisher from the carton and inspect it carefully to make sure
that no breakage or damage has occurred during shipping.
2. Do not discard any of the packing materials until all parts are accounted for.
3. Two bonnets are included: wax applicator bonnet for applying waxes, and a
reusable terry cloth bonnet for removing waxes and polishing.
4. If any of the parts are damaged or missing (refer to PARTS LIST below), return the
buffer / polisher to your nearest Sears store or Craftsman outlet to have the tool
replaced.
Your Craftsman buffer / polisher has a precision-built electric motor and it should be
connected to a 120-volt, 60-Hz AC ONLY power supply (normal household current).
DO NOT operate on direct current (DC). The large voltage drop will cause a loss of
power and the motor will overheat. If the tool does not operate when plugged into
correct 120-volt, 60-Hz AC ONLY outlet, check the power supply. This buffer / polisher
has a stub length, 2-wire power cord (no adapter needed).
This Craftsman Buffer / Polisher has the following features:
!
WARNING: If any parts are missing, DO NOT operate this
1. Powerful 1.0 Amp permanent magnet Motor with 3800 Orbits per Minute
buffer / polisher until the missing parts are replaced. Failure to do so could
result in possible serious personal injury.
provides the power needed for quality waxing, buffing and polishing.
2. Precision tuned Counterweight system reduces vibration for smooth,
comfortable operation with less operator fatigue
PARTS LIST (Fig. 1)
3. Precision tuned Counterweight System matched with Orbital Motion provides
a “swirl-free” shine.
4. Ergonomically designed Perimeter Handle System provides maximum balance,
control and gripping comfort on any horizontal or vertical surface.
5. Hook and Loop Strip helps keep extension cord securely plugged into
buffer / polisher.
6. On / Off Slide Switch conveniently located for ease in control.
7. 7-in. diameter Foam Pad follows surface contours for efficient buffing / polishing.
Chemical resistant for long life.
8. One Wax Applicator Bonnet for applying wax.
Buffer / Polisher
9. One Reusable Terry Cloth Bonnet for removing wax and polishing.
10. Non-marring Flat Top of buffer / polisher provides a stable base when applying
wax to bonnets and changing bonnets.
11. Permanently lubricated Ball Bearings for smooth, efficient operation.
12. Lightweight, High-impact Resistant Housing reduces weight, helps protect
tool from damage.
Wax
Applicator
Bonnet
Reusable Terry
Cloth Bonnet
Operator’s Manual
10
11
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION cont.
DESCRIPTION cont.
BEFORE YOU BEGIN TO WAX, BUFF AND POLISH YOUR CAR:
1. Remove all road tar, excess grease spots and bug stains with a general-purpose
cleaner.
2. Wash, clean and dry your vehicle.
3. Make sure the work area is dry.
KNOW YOUR BUFFER / POLISHER cont.
Perimeter
Non-marring Flat Top Cap
Fig. 2
On/Off
Slide Switch
Handle System
ATTACHING THE WAX APPLICATOR BONNET TO THE FOAM PAD
(See Figure 3)
Fig. 3
!
WARNING: When changing
Stub Lengh
Cord
accessories, BE SURE that the switch is
in the OFF position and the cord is
unplugged.
1. Place wax applicator bonnet on foam pad
as shown in Fig. 3.
2. ALWAYS make sure that the elastic strip
on the bottom of the bonnet is securely
tucked on the underside of the foam pad.
Hook and
Loop Strip
Foam Pad Base
APPLYING WAX TO BONNET (See Figures 4 and 5)
IMPORTANT: DO NOT APPLY WAX DIRECTLY
ON CAR!
Fig. 4
Applying Paste Wax to Bonnet (See Figure 4)
1. Spread a heaping teaspoon of wax evenly over
entire surface of applicator bonnet using a
putty knife or any other flat object (See Fig. 4).
PRODUCT SPECIFICATIONS
Pad Diameter
Motor OPM
Rating
7-in.
3800
120 volts, 60 Hz AC
1.0
Amps
Applying Liquid Wax to Bonnet (See Figure 5)
Fig. 5
1. Apply three swirls of wax over applicator
bonnet (See Fig. 5).
2. This should be enough to cover 1/4 of car
surface.
OPERATION
3. For the second and third and fourth applications,
only use about one half as much as on first
application. The bonnet will not absorb as
much wax on these applications.
Before attempting to use your tool, familiarize yourself with all of the operating
features and safety requirements.
!
WARNING: IF ANY PARTS ARE MISSING, DO NOT OPERATE THIS
BUFFER / POLISHER UNTIL THE MISSING PARTS ARE REPLACED.
FAILURE TO DO SO COULD RESULT IN POSSIBLE SERIOUS PERSONAL
INJURY.
!
CAUTION: ALWAYS wear eye protection while operating this power
tool.
12
13
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION cont.
OPERATION cont.
RUNNING YOUR BUFFER / POLISHER AND WAXING VEHICLE
RUNNING YOUR BUFFER / POLISHER AND WAXING VEHICLE cont.
1. After plugging tool into extension cord, loop
11. When you have finished applying wax with
Fig. 10
Fig. 6
extension cord over tool’s stub length plug.
Then wrap hook and loop strip around
extension cord to secure it in place.
the applicator, bonnet, SHUT OFF the
buffer / polisher before removing from the
car’s surface.
2. To avoid splashing wax, ALWAYS start and
stop the buffer / polisher against the surface
to be polished.
3. Place the extension cord over your shoulder
to keep it safely out of your way (see Fig. 6).
12. Remove the wax applicator bonnet and use
it to hand polish all the hard-to-reach
surfaces (under bumpers, around door
handles, etc.) (see Fig. 10).
13. Properly dispose of wax applicator bonnet.
4. Place buffer / polisher against vehicle and
turn buffer / polisher ON by sliding switch
to On position.
ATTACHING THE POLISHING BONNET TO THE FOAM PAD (Fig. 11)
5. Apply wax in a straight line with either a
side-to-side or back and forth motion.
ALWAYS use broad, even strokes when
applying wax (See Fig. 7).
6. Start applying wax to the flat surfaces (hood,
trunk and roof) first. Wax one section at a
time (see Fig. 8).
Fig. 11
!
WARNING: When changing
accessories, BE SURE that the switch is
in the OFF position and the cord is
unplugged.
Fig. 7
1. Place the terry bonnet on foam pad as
shown in Fig. 11.
7. After flat surfaces are covered with wax,
do the sides. The perimeter handle system
allows easy polishing of horizontal and
vertical surfaces. Hold tool with the cord
hanging free (see Fig. 9).
8. Apply wax in a thin, even coat. Too much wax
does not add any more protection and only
makes the wax removal more difficult.
2. ALWAYS make sure that the elastic strip
on the bottom of the bonnet is securely
tucked on the underside of the foam pad.
Fig. 8
BUFFING AND POLISHING - REMOVING THE WAX FROM THE SURFACE
(See Fig. 12)
1
2
3
4
Fig. 12
NOTE: Remove wax in the same order in which
it was applied.
1. Wait until wax has dried to an even haze
on vehicle.
LEFT
RIGHT
9. The random orbit motion of the buffer /
polisher provides was application that cannot
be duplicated, not even “by hand”.
2. Place extension cord over your shoulder.
3. Turn buffer / polisher ON.
IMPORTANT: DO NOT apply excessive
pressure against the work surface with this tool.
The random orbital motion feature on this tool
will perform better when less pressure is
applied. Applying excessive pressure will slow
the random orbital motion and reduce the
effectiveness of the tool.
IMPORTANT: DO NOT apply excessive
pressure against the work surface with this tool.
The random orbital motion feature on this tool
will perform better when less pressure is applied. Appling excessive pressure will
slow the random orbital motion and reduce the effectiveness of the tool.
Fig. 9
10. It is easiest to apply the wax to the entire
surface before starting the removal phase;
however, follow the specific
NOTE: For best results, use long, sweeping strokes in a criss-cross pattern when
removing wax.
4. Buff and polish the entire surface until all dried wax is removed. Remove the
bonnet from time to time and shake out the dried wax residue. A bonnet with
excess residue will cause streaking. You may need to replace the bonnet with a
new one if you can’t get it clean enough to avoid streaking.
recommendations of the wax or polish
being used.
5. Use a clean terry cloth bonnet for final buffing and polishing. Or use a foam
polishing bonnet (sold separately) for the ultimate “showroom” shine.
14
15
Download from Www.Somanuals.com. All Manuals Search And Download.
ACCESSORIES
OPERATION cont.
CAR CARE TIPS
!
WARNING: The use of attachments or accessories that are not
1. Wash and polish the car 3 to 4 times a year to help ensure paint protection.
recommended for this tool might be dangerous and could result in serious
injury.
2. Wash the car at least every 2 weeks with a car wash solution which will not harm
the finish or strip the wax. AVOID washing with household detergents.
3. Wash with a clean sponge and dry with a terry cloth towel to help prevent dirt from
scratching the paint. Start on the top and work down.
4. Remove bugs, bird droppings, tree sap and tar from the car’s surface on a daily
basis.
Sears and other Craftsman® outlets offer a large selection of Craftsman
buffer / polisher accessories designed for all your buffing and polishing
applications.
Look for these Craftsman accessories. They are specially designed to make
your 7-in. Buffer / Polisher more efficient to use.
5. ALWAYS make sure that the car’s surface is cool before washing.
6. Avoid parking near sprinklers, because water spots are difficult to remove.
7. ALWAYS keep glass cleaner chemicals away from painted surfaces. Spray the
cleaner onto a towel, NOT directly on the windows.
Wax Applicator Bonnets for applying waxes and polishes.
Terry Cloth Bonnets use for removing wax and for buffing and polishing.
Polishing Bonnets for final buffing and polishing to a “showroom” shine.
Quality Waxes for the finest protection and appearance.
MAINTENANCE
1. Terry cloth bonnets can be machine washed in cold water, using a small amount
of detergent. Machine dry at medium temperature. HOWEVER, we recommend
hand washing and air drying for longer bonnet life.
Visit your local Sears store or other Craftsman outlets or shop
sears.com/craftsman for all of the accessories for your buffer / polisher.
2. Wax applicator bonnets should only be used once, then disposed of properly.
3. Remove the bonnet from the foam pad when the buffer / polisher is not is use,
so the pad can dry out and retain its original shape.
4. To prolong the life of the foam pad, ALWAYS store the buffer / polisher with the
pad face up.
5. NEVER USE ABRASIVE COMPOUNDS WITH THIS TOOL.
6. DO NOT apply too much wax to the bonnet. Applying too much wax causes the
bonnet to become saturated and it will not last as long. THIS MAKES
POLISHING MORE DIFFICULT AND IT TAKES LONGER.
7. If the bonnet is continually coming off the pad, you may be using too much wax.
8. If buffing seems difficult, you have used too much wax.
9. ONLY USE a mild soap solution and a damp sponge to clean the buffer / polisher.
10. DO NOT immerse any part of the buffer / polisher in liquid.
16
17
Download from Www.Somanuals.com. All Manuals Search And Download.
7-in. Buffer / Polisher
PARTS LIST
MODEL NUMBER 172.107210
The model number will be found on the nameplate of the buffer/polisher.
Always mention the model number in all correspondence regarding your tool.
Item No.
Custom Parts No.
Parts No.
Parts Description
Qty.
1
2
3
4
5
6
7
8
10721-1-00
10721-2-00
10721-3-00
10721-4-00
10721-5-00
10721-6-00
10721-7-00
10721-8-00
10721-9-00
10721-10-00
10721-11-00
10721-12-00
10721-13-00
10721-14-00
10721-15-00
10721-16-00
10721-201-00
10721-17-00
10721-18-00
10721-19-00
10721-202-00
10721-20-00
10721-21-00
10721-22-00
10721-24-00
10721-60-01
10721-25-00
10721-26-00
10721-27-00
10721-28-00
10721-33-00
10721-34-00
10721-35-00
10721-37-00
10721-38-00
10721-203-00
10721-39-00
10721-40-00
10721-41-00
10721-42-00
10721-43-00
10721-52-00
10721-53-00
SW01.01.27-00
ST05.01.03-00
ST08.01.07-00
SW55.57.0-00
SA30.0.09.0-01
SA30.0.01-01
SA30.0.04-01
SA30.0.13-00
ST05.04.32-00
SA30.0.03-00
SW02.44-00
Cord & Plug
Cord Protector
Cord Clamp
Screw
1
1
1
2
1
1
1
1
2
1
1
1
1
4
2
1
1
1
2
1
1
3
1
1
1
1
1
2
2
2
1
1
10
2
2
1
1
2
1
8
2
1
1
Brand
Left Housing
Top Cover
Cushion Block
Rubber Pole
Switch Pusher
Switch
Terminal Block
Inner Wiring 110
Square Nut
Screw
Stator
Stator Set
Rotator
Bearing
Balance Block7
Plate Set
9
10
11
12
13
14
15
16
201
17
18
19
202
20
21
22
24
60
25
26
27
28
33
34
35
37
38
203
39
40
41
42
43
52
53
SW09.01-00
ST25.35.02.1-00
SA30.0.06-00
SW56.22.1-00
STA50.12.00-00
SA30.2.00
STA51.12.00-00
SW50.11.3-00
SA30.2.01-00
SA30.6.00
SW55.18.1-00
SA30.5.01-00
SW50.14.3-00
SA30.6.10-00
SW60.05.0-00
SA30.0.07-00
SA30.012-00
ST02.16.00-00
ST03.14.00-00
SA30.0.11.0-01
SA30.0.02-01
SW55.58.1-00
SA30.0.05-00
SA30.4.04-00
SA30.4.00
SA30.4.03-00
SA30.4.01-00
SA30.4.02-00
SW55.58.1-00
SW56.18.1-00
SA30.1.00.2-00
ST19.02.00-00
Screw
Press Plate
Ball Bearing
Base Plate
Washer
Screw
Rubber-Gasket
Carbon Brush
Brush Holder
Nameplate
Right Housing
Screw
Screw
Ring
Handle Set
Position Block
Top-handle7
Bottom-handle7
Screw
Screw
Rectifier-Connector
Hook And Loop
18
19
Download from Www.Somanuals.com. All Manuals Search And Download.
|