8782 Line Powered Caller ID
Speaker Phone
INSTRUCTION MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
Always follow basic safety precautions when using your telephone
equipment to reduce the risk of fire, electrical shock, and injury.
1. Read and understand all instructions in the Owner’s Instruction Manual.
2. Read all warnings and follow all instructions marked on the product.
3. Use a damp cloth for cleaning. Do not use liquid or aerosol cleaners.
4. Do not use the telephone near water. For example, do not use near a
bathtub, wash bowl, kitchen sink, laundry tub, swimming pool, or in a wet
basement.
5. Do not place this product on an unstable cart or stand. The product may
fall causing serious damage to the product.
6. Do not place any objects on the telephone line cord. Do not locate the
telephone where the line cord will be walked on.
7. Do not block or cover ventilation slots and openings in the bottom of the
telephone. The openings should never be blocked by placing the
telephone on a bed, sofa, rug, or other similar surfaces. The telephone
should never be placed near or over a radiator or heat register. The
telephone should never be placed in a built-in installation unless proper
ventilation is provided.
8. Never spill liquid on the telephone or push objects of any kind through
ventilation slots. Liquid or objects may touch dangerous voltage points or
short out parts that could result in a risk of fire or electrical shock.
9. Do not disassemble this product. Opening or removing covers may
expose you to dangerous voltages or other risks. Incorrect reassembly
can cause electrical shock when the product is subsequently used.
10. Avoid using a telephone during a local thunderstorm. There may be a
remote risk of electrical shock from lightning.
11. Do not use a telephone to report a gas leak in the vicinity of the leak.
12. Use only the batteries indicated in this manual. Do not dispose of
batteries in a fire. They may explode. Check your local codes for
possible special disposal instructions for batteries.
13. Unplug the telephone from the wall outlet and refer servicing to
qualified service personnel under the following conditions:
•
•
•
•
When the line cord is frayed or plugs damaged.
If liquid has been spilled into the telephone.
If the telephone has been exposed to rain or water.
If the telephone does not operate properly by following the operating
instructions. (Adjust only those controls covered by the operating
instructions. Improper adjustment of other controls may result in
damage and will often require extensive work by a qualified
technician to restore the product to normal operation.)
If the telephone has been dropped or the housing damaged.
If the telephone exhibits distinct change in performance.
•
•
CAUTION-Always disconnect all telephone lines from the wall outlet before
servicing or disassembling this equipment.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
TELEPHONE PART IDENTIFICATION
1.
2.
3.
Liquid Crystal Display - Displays the phone number, date and
time and other information.
One-Touch Memories - Phone numbers can be stored for
speed dialing.
Call Back
a.When reviewing Caller ID or phone book records, press to
dial the saved number.
b.Press and hold to set alarm.
4.
5.
6.
Store - Press to save numbers in one-touch memory.
- Press to enter the phone book.
Del/Set
a. Press and hold for 3 seconds while on-hook to display set-
up menu.
b. Press to delete letters or digits while editing the phone
book.
c. Press and hold for 3 seconds while viewing phone book to
delete entries.
7.
VOL
a. Press and hold while on-hook to adjust ringer volume.
b. Press while off-hook to adjust handset volume.
c. Press while on speakerphone to adjust speaker volume.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
8.
9.
AUTO RD (Auto Redial/Change Ring Tone)
a. Press to auto redial the last dialed number continuously
until the phone is answered.
b. Press and hold for 3 seconds to change ring tone.
Redial/Pause
a. Press repeatedly while on hook to review dialed numbers.
b. Press while off hook to dial the last dialed number.
c. Press while programming memory dial to store a pause.
10. Flash - Press to provide a line break signal for accessing PBX
services or Call Waiting from your local telephone company.
11.
/In Use/New/Message Waiting
a. Press for handsfree dialing and speak without lifting the
handset.
b. Plug in headset to change to headset mode. Press to
talk or to end the call.
c. Will light when the unit is in use
d. Will flash when the unit has a new call.
e. Will flash when the unit is on hold.
f. Will flash when the unit has a message waiting.
12. Hold - Press to hold the line.
13. Dialing Keys (0-9,*,#)
14. CLID
a.Press to review Caller ID Records
b.While in menu, use to select telephone settings.
15. Speaker
- Review Up and Review Down Buttons
16. Wall Mounting Hook - Turn 180 degrees to hang up the
handset when the unit is mounted on the wall.
17. Hookswitch - Press to end a call.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
18. Message Waiting Switch – Choose different forms of message
waiting.
19. Line Cord Jack - Connects telephone to telephone line.
20. DATA PORT (RJ11) - Used to connect phone to a computer or
modem.
21. Handset Jack
22. 2.5 mm Headset Jack
INSTALLATION
Batteries
1.
2.
Open the battery compartment.
Install 4 AA batteries.
Notes: The batteries are only necessary for the clock function.
They should be replaced every 6 months. Replace all 4
batteries. Observe the polarity when installing batteries.
Disconnect the phone from the line before installing
batteries.
Desk Mount
1.
Connect one end of the coiled cord to the jack in the handset
and connect the other end to the handset jack in the base.
2.
Plug one end of the line cord to the line jack in the base and
connect the other end to the wall jack.
Wall Mount
1.
Connect one end of the coiled cord to the jack in the handset
and connect the other end to the handset jack in the base.
2.
Plug one end of the short line cord to the line jack in the
base. Route the cord through the slot in the wall mount
wedge, and connect the other end to the wall jack.
3.
Install the wall mount wedge in the 4 holes in the base of
the telephone (or rotate 180° to elevate angle of phone in
desk mount position).
6
Download from Www.Somanuals.com. All Manuals Search And Download.
MESSAGE WAITING SETUP
The 8782 Message Waiting switch (see Item 18 for location)
provides 4 positions for different types of message waiting
compatibility with a wide variety of message waiting sources. See
the descriptions below to choose the switch position for your type
of Message Waiting.
1.
SR – Use this setting if you have FSK message waiting. This
is the type of MW that is usually provided by the telephone
company.
2.
3.
HV – Use this setting if your MW is 90V. This is usually
provided by a PBX.
PR1/PR2 – Use one of these settings if your MW is provided
by an Avaya or Siemens PBX with this special function.
Usually PR1 will function with Avaya and PR2 will function
with Siemens.
FUNCTION SETUP
1.
Set the Language – While on-hook, press and hold DEL/SET
for 3 seconds to enter LANGUAGE SETUP. Press CLID
select the language. Press DEL/SET to confirm. The 8782
supports 10 languages: English, Turkish, Dutch, German,
to
Swedish, Italian, Polish, Portuguese, Spanish, and French.
2.
3.
Set the Contrast - After setting the language, press CLID
to select the contrast (1-5). Press DEL/SET to confirm.
Set Year, Date and Time - After setting the contrast, the
digits of the year will flash. Press CLID
to select the
year and press DEL/SET to confirm. Use the same method to
set the month, day, and time. Note that the clock is in 24
hour format.
4.
5.
Set Local Code - After setting the date and time, the first of
five digits of the local area coded will flash. Press CLID
to select the digit and press DEL/SET to confirm. Use the
same method to set the other digits. Example: If you set up
area code 248, a call from (248)123-4567, will show on
Caller ID as 123-4567 only.
Set Prefix Code – These codes are normally used to access
a PSTN line from a PBX. After setting the local area codes,
the first of three digits will flash. Press CLID
to select the
digit and press DEL/SET to save selection. Use the same
method to set other digits if needed.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
6.
7.
8.
9.
Set the Ring Melodies – The 8782 offers a choice of 16
different ring melodies. After setting the prefix code, press
CLID
to select the desired melody (1-16) and press DEL/
SET to confirm.
Set the Ring Volume - The 8782 offers a choice of 8 different
ring volumes. After setting the ring melody, press CLID
to select the desired ring volume (1-8) and press DEL/SET to
confirm.
Set Flash Time - After setting the ring volume, press CLID
to select the flash time (100ms, 200ms, 300ms, 400ms,
600ms, 900ms) and press DEL/SET to confirm. Note: 600
mSec is the standard flash time for the United States.
Set Pause Time - After setting the Flash Time, press CLID
to select the pause time (1.2S, 2.4S, 3.3S) and press
DEL/SET to confirm.
10. Set DTMF or Pulse Mode - After setting the Pause Time,
press CLID to select the mode (DTMF or PULSE) and
press DEL/SET to confirm.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
TELEPHONE
1.
Make a Call - Pick up the handset or press
to get
dial tone and dial the number. When the called party
answers, the LCD will time the call automatically.
2.
3.
Answer a Call - Pick up the handset or press
to
answer a call.
End a Call - Hang up the handset or press
to end a
call.
4.
5.
Switch Handset to Speakerphone - Press
and then
hang up the handset to talk through the speakerphone.
Switch Speakerphone to Handset – While on a
Speakerphone call, pick up the handset and the talk mode
will switch automatically.
6.
Hold
a. Handset – While off-hook with the handset, press HOLD
and the call will be muted. The LCD will say MUTE ON.
You can still hear the other party, but the other party
cannot hear you. Press HOLD again to return to the call.
When the handset is hung up, the call is placed on HOLD
and the IN USE/NEW LED flashes. Pick up the handset
again to return to the call or press to return to the call in
speakerphone mode.
b. Speakerphone – While off-hook with the speakerphone,
press HOLD and the call will be placed on HOLD. Press
HOLD or to return to the call in speakerphone mode.
Pick up the handset again to return to the call in handset
mode.
7.
8.
Flash - This function is used for transfer on most PBX
systems and also for call waiting service from the telephone
company.
Pre-dial – While on-hook, dial the phone number and then
pick up the handset or press
dialed automatically.
. The number will be
9
Download from Www.Somanuals.com. All Manuals Search And Download.
9.
Pause - Press REDIAL/PAUSE to insert a pause in a speed
dial number.
10. Redial
a. Last Number – Go off hook. Press REDIAL/PAUSE and
the last number dialed will be dialed out.
b. Review – While on-hook press REDIAL/PAUSE repeatedly
to review the last 16 dialed numbers. When the desired
number is displayed, go off hook and it will be dialed.
11. Auto Redial – With the phone on-hook, press AUTO RD to
auto redial the last dialed number. If the line is busy when
using the monitor, the phone will automatically redial the
number up to 15 times.
12. One-Touch Speed Dial Memories:
a. STORE - With the phone on-hook, press STORE, then
input the phone number you wish to store (up to 32
digits). Then press the desired one-touch memory key
(M1 – M10).
b. DIAL - Go off hook and press M1 ~ M10 to dial the
stored phone number automatically.
CALLER ID
1.
Caller ID Review – While on-hook, press CLID
or CLID
to
review the caller’s phone number and the call time.
2.
Delete Caller IDs
a. Press CLID
or CLID
to find the call you wish to
delete. Press DEL/SET once quickly to delete a single
call.
b. Press CLID
or CLID
until a Caller ID record is
displayed. Press and Hold DEL/SET for 3 seconds to
delete all calls.
3.
Call Back from the Caller IDs – While on-hook, press CLID
or CLID
to select the number you wish to dial. Press
CALL BACK and the number will be dialed. If you have set up
LOCAL CODE and PREFIX, press CALL BACK twice to add a
prefix and area code.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
PHONE BOOK
1.
Store Phone Book Memories – While on-hook, press
LCD will display ADD SEARCH.
a. Press CLID to add. Enter the name using the keypad.
Use 0 to add a space. Use DEL/SET to delete characters.
.
b. Press
to enter the telephone number.
c. Press
to save and enter another name and phone
number. You can store up to 80 names and phone
numbers in the phone book. Once you reach 80, the
LCD will display MEMORY FULL.
2.
Review Phone Book:
a. Press
to access the phone book page. Press CLID
and LCD will display “PLS Input Name”. Enter the name to
review the telephone number.
b. Press CLID
or CLID
to review the phone book.
c. Alphabetical searching is supported. If you enter a
letter then you can review the phone book by the first
letter of the name.
Delete – While reviewing the phone book, press and hold
DEL/SET for 3 seconds to delete the name and number.
Dialing from the Phone Book
3.
4.
a. While reviewing the phone book on-hook, go off hook to
dial the displayed phone number.
b. While reviewing the phone book off-hook, press CALL
BACK to dial the displayed phone number.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE INFORMATION
Treat your telephone with care for trouble-free performance.
Avoid dropping the handset. Carefully place the handset on-hook
after use. Avoid putting near heating appliances and devices that
generate electrical noise (for example, motors and florescent
lamps).
Clean your telephone with a damp cloth. Stains may be removed
with a mild soap. Do not use liquid or aerosol detergents or
cleaning agents.
Do not expose to direct sunlight or moisture
Retain the original package in case you need to ship it at a later
date.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
TELEPHONE SERVICE PROBLEMS
If you have any problems with your telephone equipment
service, determine if the problem is with your unit or the
telephone company lines. BEFORE CALLING THE TELEPHONE
COMPANY. Be aware that they may charge you for a service call if
the problem is caused by your telephone equipment.
TROUBLESHOOTING
PHONE DOES NOT RING
•
•
•
Line cord is disconnected at telephone outlet or at
telephone end.
Phone is OFF HOOK. Make certain the hookswitch is
depressed when the handset is in the cradle.
SPEAKERPHONE is on. Turn off speakerphone.
NO DIAL TONE
Test the telephone in a different wall jack. If it works, the
first jack may be defective.
HAVE DIAL TONE BUT CANNOT DIAL OUT
•
•
Incorrect dialing mode. Switch to DTMF or PULSE mode as
needed.
BLANK SCREEN
Since this unit is line powered, the screen is blank while not
on a call.
CALLERS ARE NOT DISPLAYED ON THE SCREEN
•
•
Verify that you have subscribed to the appropriate service
(Caller ID and Call Waiting Caller ID) from your telephone
company. If you only subscribed to Caller ID service this
unit will not display the call waiting caller ID information.
Check if your answering machine is set to answer the call
before 2 rings.
•
MESSAGE WAITING LIGHT DOES NOT WORK
•
Verify that the Message Waiting Switch (see Page 6) is set
to the correct position for the MW signalling being
delivered.
CANNOT MAKE CALLS ON HEADSET
•
Verify that the headset is firmly plugged into the headset
jack on the base of the unit.
Always disconnect all the telephone cords, and then reinstall the
unit step by step per this instruction manual before asking for
service.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
TELEPHONE REPAIR
DO NOT ATTEMPT TO REPAIR THIS PRODUCT YOURSELF.
Telephones manufactured by CORTELCO must be returned to us for
repair.
You can return your telephone to CORTELCO for repair or
replacement in accordance with our LIMITED WARRANTY.
CORTELCO warrants THIS PRODUCT against defects in material
and workmanship in accordance with our LIMITED WARRANTY. If
your telephone is returned for repair, include a copy of your sales
receipt containing the date-of-purchase. DO NOT INCLUDE THE
ORIGINAL SALES RECEIPT.
If date-of-purchase is not included, the factory date printed on
the bottom of your telephone will be used as the date-of-purchase.
The factory date allows six months for distribution and sale of this
product.
If you return your telephone for repair, the warranty period is not
extended. The original date-of-purchase continues to apply to your
warranty.
OUT-OF-WARRANTY REPAIR We will repair this product for a
nominal fee after the LIMITED WARRANTY has expired if you send it
to us in a complete and undamaged condition. The repaired
telephone will be shipped to you C.O.D., freight collect.
RETURN-FOR-REPAIR PACKAGING If you are returning a unit to
us for repair, package it carefully, preferably in the original carton.
Be sure to include your return address, a copy of the sales receipt
showing date-of-purchase, and a note describing the problem you
have with your telephone. Shipping must be prepaid. If the
telephone is in warranty, it will be repaired or replaced, at our
option, at no cost to you, and it will be returned shipping prepaid.
Ship your telephone (shipping prepaid) to:
CORTELCO
REPAIR CENTER
1703 SAWYER ROAD
CORINTH, MS 38834
14
Download from Www.Somanuals.com. All Manuals Search And Download.
FCC INFORMATION
Part 68 is a Federal regulation which requires equipment to be
tested and registered with the FCC prior to its connection to the
network. This equipment complies with Part 68 of FCC rules. On the
bottom of the telephone is a label that contains, among other
information, the FCC Registration Number and the Ringer
Equivalence Number (REN) for this equipment. You must, upon
request, provide this information to your telephone company.
The Ringer Equivalence Number, which is used to determine the
number of devices you may connect to your phone line, indicates
the amount of power that your telephone draws from the
telephone company line during ringing. If you have more than one
telephone (or other terminal device) connected to the telephone
company line, you should total the ringer equivalence numbers
(REN s), and be sure that the total is not more than five. Your
telephones may not ring if the total is more than five. Also, in some
rural locations, your telephone may not ring if the REN total is more
than three.
RESTRICTIONS You must not connect your telephone to coin-
operated lines or party lines.
INSTALLATION This model telephone must be connected to the
telephone company lines through a modular jack. The required
USOC for the modular jack is RJ11C for desk mounting and RJ11W
for wall mounting. The USOC number is printed on the label on the
bottom of your telephone.
HEARING-AID COMPATIBILITY The handset on your telephone
will work with magnetically- coupled hearing aids. You can use a
hearing aid equipped with a T (Telephone) switch.
IN CASE OF TROUBLE If your telephone should cause problems
on the telephone line, the telephone company can temporarily
disconnect your service. The telephone company must then notify
and allow you to correct the problem. The telephone company may
from time to time change its lines or equipment. They must notify
you if planned changes will affect your telephone service, to allow
you to take steps to prevent interruptions.
Part 15 regulates the electromagnetic energy emitted by
equipment to minimize interference to radio, television, and other
wireless devices. This telephone complies with Part 15 of the FCC
Rules. In the unlikely event that interference occurs, move the
telephone and/or radio, television, etc. to increase the separation
distance.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY
If you purchased this product new in the U.S. or Puerto Rico,
CORTELCO warrants it against defects in material and
workmanship for a period of two (2) years from the date of original
purchase. This warranty is in lieu of all other express warranties.
During the warranty period, CORTELCO agrees to repair or, at its
option, replace the defective product, or any part of it without
charge for parts or labor. This is your exclusive remedy. This
warranty does not cover damage resulting from accident, misuse,
abuse, improper installation or operation, lack of reasonable care,
the affixing of any attachment not provided by CORTELCO with the
product and loss of parts. The warranty is voided in the event any
unauthorized person alters or repairs the unit.
Telephone companies use different types of equipment and offer
various types of services to customers. CORTELCO does not
warrant that this product is compatible with the type of
equipment of any particular phone company or the services
provided by it.
CORTELCO DISCLAIMS ANY IMPLIED WARRANTY, INCLUDING THE
WARRANTY OF MERCHANTABILITY AND THE WARRANTY OF FITNESS
FOR A PARTICULAR PURPOSE, AS OF THE DATE TWO YEARS FROM
THE ORIGINAL PURCHASE OF THE PRODUCT. CORTELCO ASSUMES
NO RESPONSIBILITY FOR ANY SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY
HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE. SOME
STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF
SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES OR
LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE
ABOVE EXCLUSION AND LIMITATION MAY NOT APPLY TO YOU.
If failure occurs and your telephone is in warranty, service shall be
provided by returning it to CORTELCO - Repair Center, 1703
Sawyer Road, Corinth, Mississippi 38834, shipping prepaid. The
product will be repaired or replaced if examination by us
determines the product to be defective. Telephones received
damaged as a result of shipping will require you to file a claim with
the carrier.
8782 - Rev. 1.1
16
Download from Www.Somanuals.com. All Manuals Search And Download.
|