IMI CORNELIUS INC g One Cornelius Place g Anoka, MN 55303-6234
Telephone (800) 238-3600 Facsimile (800) 535-4321
INSTALLATION INSTRUCTIONS, BIN STAT KIT, P/N 630000408
These Bin Stat kits apply to all “I” Series Ice makers
Table 1. Loose–Shipped Parts
Item No.
Part No.
630900413
70894
Name
Qty.
1
1
1
1
1
1
1
1
2
3
4
5
6
7
Spacer, Hex 5/8” Long x 8–32 SS
Screw MA 08–32 TRPH 24 SS
Spacer
Thermostat Asy
Bin Stat Support
51348
630000413
620037008
630460064INS
168833002
Installation Instruction, Thermostat
Washer SR 4W SS E#8
1. Disconnect power.
2. Remove front cover of the unit and the electrical box cover plate.
3. Carefully insert the coiled capillary tube through the bottom hole in the electrical box where the elec-
trical wires are coming through (see Figure 4).
4. If there is not a hole already in the chassis base, drill a ½” hole in the chassis base as indicated in
Figure 3.
5. Straighten approximately 12” of cap tube to go through hole. Re–coil the remainder. Do not disturb
coiled end.
6. Insert the “1/4” diameter wire form support into the coiled end of capillary tube and insert the assem-
bly through the hole in the chassis base. Route capillary tube to follow support as closely as pos-
sible.
7. Remove the 8–32 nut (closest to the ½” DIA hole) that holds the compartment wall to the base. The
adapter kits that have a single level, adapter kits P/N’s 02390, 630200153, 08006, 02388, 08004,
630000191 and 08010) require a 7/8” high spacer be used to mount the binstat support. Thread the
8–32 x 5/8” hex spacer on to the compartment stud. Then fasten the thermostat support to the hex
spacer using the ¼” high plastic spacer, #8 flat washer and 8–32 x ¾” long phil. head screw. The
spacers are not to be used on the elevated adapter kits. Refer to Figure 2.
8. Any excess capillary tubing must be pulled back into the compressor compartment to prevent ice
from damaging it during dispenser operation.
9. Seal ½” diameter hole with sealant (RTV).
March 2, 2004
IMI CORNELIUS INC. 2004
1
Rev A
630460064INS
Download from Www.Somanuals.com. All Manuals Search And Download.
March 2, 2004
Rev A
630460064INS
IMI CORNELIUS INC. 2004
3
Download from Www.Somanuals.com. All Manuals Search And Download.
BIN STAT SUPT ASY FOR
SINGLE LEVEL ADAPTOR KIT NO:
02388, 08004,630000191, 02390,
630200153, 08006, & 08010
WASHER
ICEMAKER E-BOX
8–32 X 3/4 PHMS
620037008, BIN STAT SUPT
CAPILLARY TUBE
COIL CAPILLARY TUBE
AROUND BIN STAT SUPT
1/4 SPACER
5/8 SPACER
ELEVATED
ADAPTOR KIT
CAPILLARY ASY
8–32 NUT (PART OF ICEMAKER)
WASHER
620037008, BIN STAT SUPT.
8–32 STUD (PART OF ICEMAKER)
SINGLE LEVEL
ADAPTOR KIT
BIN STAT SUPT ASY FOR ALL
ELEVATED ADAPTOR LID KITS
FIGURE 2
Download from Www.Somanuals.com. All Manuals Search And Download.
TOP VIEW OF 1230 CHASSIS PLATE
ICE
DROP
ZONE
ICE
DROP
ZONE
ICE
DROP
ZONE
1/2” DRILL
ICE
DROP
ZONE
4.25*
1.50
* DIMENSION IS FROM FRONT
OF UNIT WITHOUT COVER.
15.41
Figure 3
CLEAN MOUNTING AREA WITH
SCOTCH BRITE PAD,
ELECTRICAL BOX ASY
THEN WIPE AREA DOWN WITH
RUBBING ALCOHOL AND LET DRY
THERMOSTAT KIT ASY
630000408
COIL
TO CHASSIS
PLATE
Figure 4
March 2, 2004
Rev A
630460064INS
IMI CORNELIUS INC. 2004
5
Download from Www.Somanuals.com. All Manuals Search And Download.
|