ColdFusion Icemaker Adapter Kit Installation Instructions
INSTALLATION INSTRUCTIONS
FOR ADAPTER KIT P/N 629096828
This adapter kit is recommended for use with Cold Fusion Dispensers and Icemakers that measure 30" wide X
24.5" deep. The icemaker drop zone and bin stat must fit within the footprint shown in figure 1.
30.30”
1.67”
(BACK SIDE OF DISPENSER)
27.40”
ICE MAKER DROP ZONE
21.50”
AND BIN STAT MUST FIT
WITHIN THE
27.40 X 21.50” OPENING
Figure 1
!
WARNING:
Disconnect power to the unit before installing adaptor following all lock out / tag out procedures established by the
user. Verify all of the power is off to the unit before performing any work. Failure to comply could result in serious
injury, death or damage to the equipment.
!
WARNING:
All of the attachment screws and plates must be installed as directed in this manual. Failure to comply could result in
serious Injury, Death or Damage to the equipment.
Release Date: October 8, 2008
© 2008-2010, IMI Cornelius Inc.
Revision: B
1 of 4
Publication Number: 629096828INS
Download from Www.Somanuals.com. All Manuals Search And Download.
ColdFusion Icemaker Adapter Kit Installation Instructions
5.
6.
When ready, lift the machine onto the counter.
Position the icemaker on top of the kit. Do not slide the icemaker into position. This may tear the gasket
material on top. Instead, lift and position the icemaker into place. The back side of the icemaker should line
up with the back of the kit. Side walls should also be centered from left to right. Connect the icemaker
according to the manufacturer’s requirements.
7.
8.
Apply a continuous bead of silicone (supplied) around the icemaker to seal it to the kit. (For reference -
Silicone is NSF International Listed Silastic Sealant, Dow 732 or equivalent).
The next step is to secure the icemaker to the kit. Use the brackets (supplied) as templates to drill four 9/64”
(.140” Dia.) holes into the adapter kit (2 per side). When drilling holes, the maximum distance from the back
of the kit is 7.50 inches (refer to Figure 4) . Failure to comply will result in damage to the sliding arm
mechanisms internal to the kit. Drill four holes of the same diameter into the icemaker (2 per side). Ensure
the location of the brackets will not damage the kit or the icemaker prior to drilling any holes. USE
EXTREME CAUTION NOT TO DRILL INTO ANY OTHER COMPONENTS. Drill depths should not go
further than the thickness of the material being drilled (just enough to go through). Secure the two brackets
using the screws provided.
DETAIL “A”
DEATIL A
Figure 4
Installation is complete. For optimal performance, Do not fill ice bin to more than 2/3 of capacity. Recommended
maximum fill height is four (4) inches from the top of the bin.
© 2008-2010, IMI Cornelius Inc.
3 of 4
Publication Number: 629096828INS
Download from Www.Somanuals.com. All Manuals Search And Download.
ColdFusion Icemaker Adapter Kit Installation Instructions
Adapter Kit Operating Instructions
1.
The plastic lid of the kit slides in and out and also hinges upward. This provides access to the hopper in the
event manual ice filling is required. Simply pull out the lid and hinge upward. The lid will remain in the up
position on its own.
2.
If manual filling is required, the lid must be pulled out and lifted up out of the way. Do not leave the lid down
and rest a bucket of ice on it while manual filling as this may cause damage to the lid.
- COMPLETED ASSEMBLY –
COLD FUSION DISPENSER WITH ADAPTER KIT
P/N 629096828, AND 30” X 24.5” ICE MAKER
Figure 5
Publication Number: 629096828INS
4 of 4
© 2008-2010, IMI Cornelius Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
|