ED/DF300 22” CCM322/522 Nordic Style Lid Kit Installation Instructions
INSTALLATION INSTRUCTIONS
ED/DF300 22” CCM322/522 NORDIC BLACK/GRAY STYLE LID KITS
This Nordic style kit applies to the Cornelius 22” wide CCM322/522 ice maker.
Item
No.
Part No.
15210
Name
Qty.
1
2
3
4
Lid Assembly
1
2
1
1
22127
50904
52946
52964
91957
Icemaker Mounting Bracket
RTV. 3Oz Tube
Manual Ice Fill Cover, Black
Manual Ice Fill Cover, Gray
5
Label, “Disconnect Power Before
Cleaning”
1
6
7
8
9
620042919
620701601
620701902
620701901
ED300 Ice Baffle
1
8
4
4
4
1
1
#10 x 1/2” LG. Sheetmetal Screw
#8–32 Nylon Acorn Nut
Sealing Washer
10 621701903
#8 Nylon Washer
11 620204725INS Installation Instructions
13 630500109 Bin Stat
CAUTION: Disconnect electrical power to the dispenser before proceeding with the icemaker
adapter kit installation.
WARNING: The dispenser must be secured with 3/8-16 bolts (6) to the counter before installing
this Icemaker Adapter Kit. Refer to the installation manual and Figure 2 for the counter mounting
template.
NOTE: Adjust the automatic agitation timer located in the dispenser’s electrical control box to 5 seconds
on, 20 minutes off. Access to the timer is provided by removing the merchandiser/upper front panel.
1.
Remove the (2) screws from each side of the dispenser cabinet. and the plastic hopper covers (2)
that were shipped with the unit.
2.
3.
Place the “K” style lid on the unit and use the (4) screws that were removed to fasten the lid in
place.
Install the ice baffle on the lid assembly as shown in Figure 2.
IMPORTANT: The baffle prevents ice from over–filling the manual fill area during agitation/
dispensing with a full storage bin and forcing the manual fill cover off.
4.
Seal the icemaker to the top of the dispenser after determining the correct location for the ice maker
(see Figure 1).
A. Run beads of RTV around the opening in the lid and inside of the perimeter of the ice maker
outline so that the ice maker will set on the RTV.
B. Set the ice maker onto the lid and position it as required.
C. Wipe away the excess RTV.
5.
6.
5. Drill .147 diameter holes into the ice maker cabinet and the dispenser lid using the icemaker
mounting brackets as templates. USE CAUTION SO AS NOT TO DRILL INTO ANY ICEMAKER
COMPONENTS (CONDENSER, TUBING, ETC.). Secure the brackets using the #10 sheetmetal
screws provided.
Install the wire form bracket, supplied with the bin stat kit (item 4), through the 5/8” diameter hole in
the bottom of the ice maker. Wrap the eye of the wireform over the stud near the hole to the end of
Release Date: October 5, 2007
© 2007, IMI Cornelius Inc.
Revision: A
Publication Number: 620204725INS
- 1 -
Download from Www.Somanuals.com. All Manuals Search And Download.
ED/DF300 22” CCM322/522 Nordic Style Lid Kit Installation Instructions
8
ICEMAKER SHOWN
4 PLC.
FOR REFERENCE
ONLY
9
4 PLC.
BAFFLE
(ITEM 6)
SHOWN
IN PLACE
1
10
4 PLC.
6
FIGURE 2. ED/DF300 Kit
7/16
Ø
(6) PLCS
44 3/8
40 3/4
1 13/16
20 3/8
16 1/8
2 9/16
4 1/2
1 5/16
OPENING
12
18 5/8
21 1/4
29 3/4
31 1/2
15
8 1/2
REMOVABLE
SINK
TO FRONT OF DRIP TRAY
ON COUNTER
6 11/16
3 1/2
8 5/8
15
TOP
TO FRONT TOP OF
DRIP TRAY
3 3/16
22 3/8
RECOMMENDED COUNTER OPENING SIZE 12” X 15”
FOR UTILITIES AND BEVERAGE TUBING.
FIGURE 3. ED/DF300 Mounting Template
© 2007, IMI Cornelius Inc.
- 3 -
Publication Number: 620204725INS
Download from Www.Somanuals.com. All Manuals Search And Download.
ED/DF300 22” CCM322/522 Nordic Style Lid Kit Installation Instructions
FIGURE 4. Bin Stat
Publication Number: 620204725INS
- 4 -
© 2007, IMI Cornelius Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
|