INSTALLING THE SWITCH
TROUBLESHOOTING
ADJUSTMENTS
WARNING: Turn power off at the circuit breaker before wiring.
If you have a problem with your Wall Switch, first follow this guide. If the problem persists, call the
customer service hotline at 1-866-853-4293 between 8:00 AM and 7:00 PM ET weekdays.
6105
TIME
LIGHT LEVEL
• Remove the decorative coverplate (secured by two
screws).
SYMPTOM
POSSIBLE CAUSE
SYMPTOM
POSSIBLE CAUSE
• Remove Control Cover. (Press in with screwdriver.
Swing out cover to remove.)
• Remove the existing switch (if this is a retrofit
application).
• Connect the detector as shown in the diagram.
Before installing the detector into the box, make
sure there is no wire exposed at the connection.
• Do not connect to neutral wire or damage to unit
will occur.
There are 6 preset selections for the amount
of time the lights stay on: Test (5 seconds),
1, 5, 10, 15, and 20 minutes. Use a small,
phillips screw driver to adjust the TIME
control. Turn the TIME control until it “snaps”
into the desired time position.
The sensor can be prevented from turning on lights
when there is already enough light in the room. Use
a small screw driver to set the light level using this
diagram as a guide. In the fully clockwise position,
the sensor turns on lights even in full daylight. In the
fully counter-clockwise poition, the sensor only turns
on lights when the surrounding light level is very low.
Motion Sensing
Wall Switch
1.
Light does not come
on.
Circuit breaker or fuse is
turned off.
Light does not
turn off.
1. Incorrect wiring.
2. MODE switch is set to
ON instead of AUTO.
3. Motion is still present.
4. Delay set by TIME
control has not
expired.
2.
3.
If the lamp being con-
trolled has another switch,
it may be turned off.
Bulb is defective.
The 6105 Motion Sensing Wall Switch detects motion to turn on
lights for an adjustable amount of time. A built-in photo cell can be set
to keep lights off when the lights aren't needed. The unit has excel-
lent sensitivity and a wide 150° detection range. It can be used with
incandescent lighting as well as rapid start fluorescent lighting. (Not
for use with electronic ballasts)
OFF AUTO
ON
4. LIGHT control is set too
far toward the DARK posi-
1. Heating or cooling ob-
jects (such as air
vents, appliances, or
drafts through the wall
box) are causing false
triggering.
Light comes on for
no reason in the Auto
mode.
5.
tion. MODE switch is set
to OFF instead of AUTO.
Poor connection.
Any Light
Level
Dark (low
light level)
To adjust the photocell:
• When the light in the room is at the
level you want the lights to turn on,
set the switch to the AUTO position.
• Put the TIME control to the 5 sec-
ond position.
• Put the LIGHT control to the mini-
mum dark (fully counter-clockwise)
position. Wait for the lights to turn
off.
• Turn the LIGHT adjustment clock-
wise in very small steps and wait 2
seconds before moving your hand in
front of the sensor. Repeat until the
lights controlled by the sensor come
on. The light will now come on when
the light level is at or below the pres-
ent level and motion is detected.
6.
1.
Installation is as easy as replacing a wall switch. However, some
codes require installation by a qualified electrician.
Lights do not stay
on in the Auto mode.
Motion has stopped in the
room.
TIME control is set for too
short a delay.
+
5
10
2.
2. Switch on the sensor
has been turned off
and back on.
Features include:
• 150° motion detection angle.
1
15
Test
20
• Adjustable on-time from 5 sec. to 20 min.
• Adjustable photocell.
• Works with incandescent and rapid start fluorescent lighting.
(Not for use with electronic ballasts)
• Works with motors up to 1/8 hp.
3. There was a momen-
tary power interrup-
tion. The light will turn
off automatically when
the "on" time expires.
T I M E
L I G H T
5 Seconds
20 Minutes
LOAD
BLACK
(NEUTRAL)
SPECIFICATIONS
• Slide switch selectable OFF, ON AND AUTO modes.
LIGHTING
LOAD
Note: Adjusting screws
found under (Off-Auto-On)
face plate.
Electrical input................................................................................................................................120V, 60 Hz
Fluorescent Load (Not for electronic ballasts)....................(2) 30 Watt minimum 400 Watt maximum Rapid Start
Motor Load.............................................................................................................................1/8 HP maximum
Incandescent.........................................................................................................................500W at 120V AC
On-Time..........................................................................................Adjustable approximately 5 sec. to 20 min.
Photocell Sensor.......................................................................................From dull daylight to less than 1 FC.
Coverage...............................................................................up to 15 ft. at 150°, up to 30 ft. in front of the sensor
Control Cover
Plate Removed
Included are: • The sensor switch • Cover plate • 3 wire connectors • 2 large screws • 2 small screws.
Green ground wire to
junction box screw or
grounding wire.
+
5
10
1
15
Test
20
30'
T
I
M
E
L
I
G
H
T
INSTALLATION
MODE
Selection
Switch
Complete Installation
• Replace control panel cover and install the decorative wall plate. In installations where the Cooper motion
sensor switch is combined with other switches or outlets on an expanded box, a combination wall plate will
need to be purchased. Various combination wall plates are available at Home Centers and Electrical Supply
Stores.
WARNING: For indoor use only.
BLACK
SELECT A LOCATION
HOT
(LINE)
YOUR COOPER WIRING DEVICES MOTION SENSOR TWO YEAR LIMITED WARRANTY
NEW APPLICATION
For a period of 2 years from the date of purchase, Cooper Wiring Devices will replace or repair the motion
sensing switch provided that it has not been subject to abuse, improper installation or improper use, and
is returned prepaid Cooper Wiring Devices Quality Control Department at 203 Cooper Circle, Peachtree
City, GA 30269. If the product has been discontinued, replacement will be made with the nearest available
equivalent model. This warranty does not cover consumables (such as fuses). Proof of purchase in the
form of a bill of sale or receipted invoice that shows that the item is within the applicable warranty period
must be presented to obtain the repair or replacement provided by the warranty. Repair or replacement as
provided under this warranty is the exclusive remedy of the customer. Cooper Wiring Devices shall not be
liable for any incidental or consequential damages for breach of any express or implied warranty on any
of its products. Except to the extent limited or prohibited by applicable law, any implied warranty of mer-
chantability or fitness for a particular purpose on this product is limited in duration to the duration of this
warranty. Some states do not allow the exclusion or limitation of incidental or consequential damages, or
allow limitations on how long an implied warranty lasts, so the above limitations may not apply to you. This
warranty gives you specific legal rights and you may also have other rights which vary from state to state.
Choose a location where the motion sensor has a clear view of
• Slide the switch a couple of times to make sure it operates freely.
the entire area where occupant motion may occur.
15'
TYPICAL INSTALLATION
• Mount the detector into the wall box with the mounting screws.
• For test purposes, use a small screwdriver to turn the time control to TEST and the light control fully clockwise.
Turn the power back on at the circuit breaker.
• Set the switch to the AUTO mode. When unit stabilizes (about 1 minute) the sensor is ready to detect motion. If
motion is detected, the lights will turn on. The lights will turn off 5 seconds after motion is no longer detected.
RETROFIT APPLICATION
0'
Motion sensing switch will replace existing wall switch. Use only
USE
where the existing switch location provides a clear view of the
occupied area.
Typical Plan View of Coverage
MODE Selection Switch
Moving the switch selects one of three modes of operation: OFF, AUTO, ON
GENERAL APPLICATION INFORMATION
The detector is more sensitive to motion across the front of the sensor than to motion towards the sensor.
OFF: Lights stay off.
Questions? Call 1-866-853-4293 8:00 AM to 7:00 PM Eastern Time, weekdays
- 2 -
AUTO: Lights come on for time set when motion is detected and the light level is below the set level.
ON: Lights stay on continuously.
The detector senses heat in motion and possible heat sources that change temperature quickly. Therefore, to
avoid false triggering, avoid placing the sensor where it will be aimed at air conditioners, heaters, and other
sources of heat or cold.
598-1177-03 E
Download from Www.Somanuals.com. All Manuals Search And Download.
- 3 -
- 4 -
469MV-PT
|