Cooper Bussmann TV Receiver BU 905U L R User Manual

Read  
Cooper Bussmann  
BU-905U-L-R Receiver  
Quick Start Guide  
Version 1.8  
and Retain  
for Future  
Reference  
3A1578Rev1.8  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Cooper Bussmann BU-905U-L-R Receiver Quick Start Guide  
Unit Components and Connections  
Your BU-905U-L-R receiver unit has the following components and terminal connections:  
IMPORTANT ELECTRICAL SAFETY INFORMATION  
In order to comply with Electrical Safety Regulations, this module must be installed in an Electrical AND Fire enclosure. This enclosure may be a  
single or multiple enclosures. Access to the module is to be made by a Service Person only.  
In order to comply with Electrical Safety Standards, when connecting SELV AND voltages which are greater than SELV (30Vac or 60Vdc) together,  
then Relay Output 2 must NOT be used in order to provide sufficient isolation between the outputs  
3A1578Rev1.8  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Cooper Bussmann BU-905U-L-R Receiver Quick Start Guide  
Front Panel Components  
SMA Antenna Connector at Top of Unit  
Indicator LEDs  
RS232 Configuration Port  
RSSI Push-Button  
The LEDs on the front panel indicate the unit status:  
LED Status  
None  
Indicates  
No power supply.  
OK LED Green  
OK LED Red  
RX LED Flashes  
CF LED ON  
PG LED on  
Current status of the unit OK.  
Fault condition detected in unit.  
Receiving Message.  
Module Communication Failure Output is active.  
Configuration Cable Connected.  
The Output LEDS (i.e., D1, D2, D3) light when the corresponding output is active.  
Output LED ON  
D1  
D2  
D3  
Relay output D1 is ON (Contact Closed).  
Relay Output D2 is ON.  
Relay Output D3 is ON.  
LEDs with RSSI Push  
Button Pressed  
When you press the RSSI push button, the unit shows the signal strength by lighting the LEDs  
from the bottom to the top. Signal strength is the strength of the last message received that  
was addressed to this station.  
LED Signal Strength  
LED Signal Strength  
D1  
D2  
D3  
More than -85 dBm  
More than -90 dBm  
More than -95 dBm  
RX  
CF  
PG  
More than -100 dBm  
More than -105 dBm  
Always on during RSSI test  
Output LED flashing  
quickly  
If an output is in communication failure, the corresponding LED flashes at 5Hz.  
D1  
D2  
D3  
PG  
Relay Output D1 is in communication failure.  
Relay Output D2 is in communication failure.  
Relay Output D3 is in communication failure.  
Analog output is in communications failure.  
4
3A1578Rev1.8  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Cooper Bussmann BU-905U-L-R Receiver Quick Start Guide  
Antenna Installation  
Resetting Your Unit to Factory Defaults  
You must reset the receiver unit to factory defaults before linking the transmitter and receiver units.  
To reset the default factory configuration:  
1. Press and hold the RSSI push button.  
2. Power on the BU-905U-L-R receiver.  
3. The BU-905U-L-R receiver flashes all LEDs at medium flash (i.e., 1.6Hz).  
NOTE: If the LEDs do not flash, you must repeat steps 1 and 2 until the LEDs flash before continuing.  
4. Release the RSSI push button within 5 seconds.  
5. Within a further 60 seconds, press and hold the RSSI push button for 5 seconds (until the LEDs stop flashing) and then release.  
6. The BU-905U-L-R receiver lights all LEDs for 2 seconds before returning to normal operation.  
NOTE: If the LEDs do not light, you must repeat the process from step 1 until the LEDs light before continuing.  
7. You can now link the transmitter and receiver units.  
3A1578Rev1.8  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Cooper Bussmann BU-905U-L-R Receiver Quick Start Guide  
Linking Your Transmitter and Receiver Units  
You must reset the transmitter unit to factory defaults (to disable encryption) before linking the transmitter and receiver units.  
For more information, see the BU-905U-L-T Transmitter Quick Start Guide.  
NOTE: You must complete the linking process in 60 seconds.  
To link the transmitter and receiver units:  
1. Press and hold down the RSSI Pushbutton on the receiver.  
2. Power on the receiver while holding down the RSSI Pushbutton  
3. Release the RSSI Pushbutton as soon as the Receiver LEDS flash (within 5 seconds of powering the receiver).  
4. The receiver will flash all LEDs for a maximum 60 seconds while it tries to link to the transmitter.  
5. Power on the transmitter. The transmitter sends a special “Link” message to allow the receiver to recognize the transmitter.  
6. When the units link, the receiver lights all LEDs for 2 seconds before returning to normal operation.  
NOTE: If the receiver LEDs continue flashing within the 60 seconds, the units are not linked and you should retry the linking process by powering  
the transmitter off and on again. If you exceed the 60 seconds, you must restart the linking process from step 1.  
7. You can now bench test your configuration before deploying.  
Safety information  
Thank you for selecting the BU-905U-L-R receiver for your telemetry needs. We trust it will give you many years of valuable service. To ensure  
your BU-905U-L-R receiver enjoys a long life, double-check ALL your connections with the user’s manual before powering on the unit.  
WARNING: Incorrect termination of supply wires may cause internal damage and will void warranty.  
Exposure to RF energy is an important safety consideration. The FCC has adopted a safety standard for human exposure to radio frequency  
electromagnetic energy emitted by FCC regulated equipment as a result of its actions in Docket 93-62 and OET Bulletin 65 Edition 97-01.  
FCC Notice When Used in USA: BU-905U-L Wireless I/O Module  
Part  
Additional information  
15  
This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part15 of the FCC  
rules (Code of Federal Regulations 47CFR Part 15). Operation is subject to the condition that this device does not cause  
harmful interference.  
90  
This device has been type accepted for operation by the FCC in accordance with Part90 of the FCC rules (47CFR Part 90).  
See the label on the unit for the specific FCC ID and any other certification designations.  
Industry Canada: BU-905U-L Wireless I/O Module  
RSS-119 - This device has been type accepted for operation by Industry Canada in accordance with RSS-119 of the Industry Canada rules. See  
the label on the unit for the specific Industry Canada certification number and any other certification designations.  
NOTE: Any changes or modifications not expressly approved by Cooper Bussmann P/L could void the user’s authority to operate this equipment.  
To operate this equipment legally the user must obtain a radio-operating license from the government agency. This is done so the government can  
coordinate radio users in order to minimize interference.  
Safety Information - FCC Notice  
This device complies with Part 15.247 of the FCC Rules. Operation is subject to the following two conditions:  
• This device may not cause harmful interference; and  
• This device must accept any interference received, including interference that may cause undesired operation  
NOTE: This equipment is suitable for use in Class 1 Division 2 groups A, B and C or non-hazardous locations only.  
6
3A1578Rev1.8  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Cooper Bussmann BU-905U-L-R Receiver Quick Start Guide  
Unit Specifications  
Input/Output  
Number  
Additional Information  
Digital Outputs  
3
Voltage-free contacts rated at 250Vac 1A, 30Vdc 1A.  
2 for digital inputs and 1 for setpoint.  
Status Outputs  
Analog Output  
Power Supply  
2
1
1
Separate System OK and communication failure output.  
16-bit resolution, 0.1% accuracy, single-ended source output.  
9-30Vdc 0.25 Amp CSA certified Class 2 power supply. For use in Class I Div 2  
hazardous locations, the power supply must be approved for Class I Div 2 use.  
WARNING: Explosion hazard - do not disconnect while circuit is live unless area  
is known to be non-hazardous.  
Radio Receiver  
Frequency  
1
High sensitivity FHSS UHF radio receiver.  
Actual frequency range depends on country.  
At BER 8%.  
902 – 928MHz  
-110 dBm  
Sensitivity  
Document Information  
Quick Start Guide Cooper Bussmann BU-905U-L Wireless I/O Receiver Unit Version 1.8  
Cooper Bussmann Contact Details  
Telephone  
Fax  
636-527-1270  
636-527-1607  
E-mail  
Website  
3A1578Rev1.8  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Customer Assistance  
Customer Satisfaction Team  
Application Engineering  
Available to answer questions regarding Cooper  
Bussmann products & services Monday-Friday,  
8:00 a.m. – 4:30 p.m. for all US time zones.  
Contact:  
Technical assistance is available to all customers.  
Staffed by degreed engineers, this application support  
is available Monday-Friday, 8:00 a.m. – 5:00 p.m. CT  
Contact:  
s Toll-free phone: 855-287-7626 (855-BUSSMANN)  
s Toll-free fax: 800-544-2570  
s E-mail: [email protected]  
s Phone: 636-527-1270  
s Fax: 636-527-1607  
s E-mail: [email protected]  
Emergency and After-Hours Orders  
Online Resources  
resources:  
Next flight out or will call shipment for time-critical needs.  
Customers pay only standard product price, rush freight  
charges, & modest emergency service fee. Place these  
orders through the Customer Satisfaction Team during  
regular business hours. For after-hours, contact:  
s Product search & cross-reference  
s Product & technical materials  
s Solutions centers for information on topical issues  
including arc-flash, selective coordination &  
short-circuit current rating  
s Technical tools, like our arc-flash calculator  
s Where to purchase Cooper Bussmann product  
s Phone: 314-995-1342  
3
C
– the Enhanced, Online Cooper Customer Center  
Provides real time product availability, net pricing, order  
status & shipment tracking across six Cooper divisions:  
B-line, Bussmann, Crouse-Hinds, Lighting, Power  
Systems & Wiring Devices. Available at:  
Services  
Cooper Bussmann Services team provides engineering  
expertise in electrical system reviews, electrical safety  
training & component testing for Agency compliance.  
Contact:  
s 877-995-5955 for log-in assistance  
s Phone: 636-207-3294  
s E-mail: [email protected]  
Cooper Bussmann  
St. Louis, MO 63178  
855.287.7626 (855-BUSSMANN)  
Your Authorized Cooper Bussmann Distributor is:  
©2011 Cooper Bussmann  
PDF Only  
8
3A1578Rev1.8  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Craftsman Tiller 9172933 User Manual
Cuisinart Convection Oven TOB 100 User Manual
Cuisinart Cooktop GC 17N User Manual
Cuisinart Food Processor CH 4DC User Manual
Electro Voice Speaker QRx 218S User Manual
Euro Pro Carpet Cleaner S3305H User Manual
Everpure Water System EV9275 60 User Manual
Fellowes Paper Shredder 420 2HS User Manual
Frigidaire Clothes Dryer 131842900 9903 User Manual
Global Machinery Company Impact Driver ATI2K User Manual