INSTALLER: THESE INSTRUCTIONS MUST BE CONVEYED TO AND REMAIN WITH THE HOMEOWNER.
CERTIFIED UNDER CANADIAN AND AMERICAN NATIONAL STANDARDS, CSA 2.33, ANSI Z21.88 FOR VENTED GAS FIREPLACE HEATERS
GAS-FIRED DIRECT VENT INSERT
INSTALLATION AND OPERATION INSTRUCTIONS FOR:
VENTED GAS FIREPLACE HEATER
NATURAL GAS MODELS CDIZC - N
PROPANE GAS MODELS CDIZC - P
CERTIFIED FOR CANADA AND UNITED STATES USING ANSI / CSA METHODS
WARNING: If the information in these instructions is not followed exactly, a fire or
explosion may result causing property damage, personal injury or death.
FOR YOUR SAFETY
Do not store or use gasoline or other flammable vapours and liquids in the vicinity
of this or any other appliance.
WHAT TO DO IF YOU SMELL GAS:
• Do not try to light any appliance.
• Do not touch any electrical switch.
• Do not use any phone in your building.
supplier's instructions.
• Immediately call your gas supplier
from a neighbour's phone. Follow the gas
• If you cannot reach your gas supplier,
call the fire department.
Installation and service must be performed by a qualified installer, service
agency or the gas supplier.
R-2000
Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON L4M 4Y8 Canada • (705)721-1212 • fax(705)722-6031
W415-0224 / D / 01.15.04
Download from Www.Somanuals.com. All Manuals Search And Download.
3
CONTINENTAL gas fireplaces are manufactured under the strict Standard of the world recognized
ISO 9001 : 2000 Quality Assurance Certificate.
CONTINENTAL products are designed with superior components and materials, assembled by trained craftsmen
who take great pride in their work. The burner and valve assembly are leak and test-fired at a quality test station.
Once assembled the complete fireplace is thoroughly inspected by a qualified technician before packaging to ensure
that you, the customer, receives the quality product that you expect from WOLF STEEL Ltd..
CONTINENTAL GAS FIREPLACE PRESIDENT'S LIFETIME LIMITED WARRANTY
The following materials and workmanship in your new CONTINENTAL gas fireplace are
warranted against defects for as long as you own the fireplace. This covers: combustion cham-
ber, heat exchanger, stainless steel burner, phazer™ logs and embers, ceramic glass (thermal
breakage only), gold plated parts against tarnishing, porcelainized enamelled components and
aluminium extrusion trims.
Electrical (110V and millivolt) components and wearable parts such as blowers, gas valves,
thermal switch, switches, wiring, remote controls, igniter, gasketing, and pilot assembly are
covered and WOLF STEEL LTD. will provide replacement parts free of charge during the first
year of the limited warranty.
Any labour related to warranty repair is not covered.
CONDITIONS AND LIMITATIONS
WOLF STEEL LTD. warrants its products against manufacturing defects to the original purchaser only -- i.e., the individual or legal entity (registered customer) whose name appears on
the warranty registration card filed with WOLF STEEL Ltd. -- provided that the purchase was made through an authorized CONTINENTAL dealer and is subject to the following conditions
and limitations:
This factory warranty is nontransferable and may not be extended whatsoever by any of our representatives.
The gas fireplace must be installed by a licenced, authorized service technician or contractor. Installation must be done in accordance with the installation instructions included with the
product and all local and national building and fire codes.
This limited warranty does not cover damages caused by misuse, lack of maintenance, accident, alterations, abuse or neglect and parts installed from other manufacturers will nullify this
warranty.
This limited warranty further does not cover any scratches, dents, corrosion or discolouring caused by excessive heat, abrasive and chemical cleaners nor chipping on porcelain enamel
parts, mechanical breakage of PHAZER™ logs and embers, nor any venting components used in the installation of the fireplace.
WOLF STEEL Ltd. warrants its stainless steel burners against defects in workmanship and material for life, subject to the following conditions: During the first 10 years WOLF STEEL
Ltd. will replace or repair the defective parts at our option free of charge. From 10 years to life, WOLF STEEL LTD. will provide replacement burners at 50% of the current retail price.
In the first year only, this warranty extends to the repair or replacement of warranted parts which are defective in material or workmanship provided that the product has been operated in
accordance with the operation instructions and under normal conditions.
After the first year, with respect to this President's Limited Lifetime Warranty, WOLF STEEL LTD. may, at its discretion, fully discharge all obligations with respect to this warranty by refunding
to the original warranted purchaser the wholesale price of any warranted but defective part(s).
WOLF STEEL Ltd. will not be responsible for installation, labour, or any other costs or expenses related to the reinstallation of a warranted part, and such expenses are not covered by this
warranty.
Notwithstanding any provisions contained in this President's Limited Lifetime Warranty, WOLF STEEL’S responsibility under this warranty is defined as above and it shall not in any event
extend to any incidental, consequential or indirect damages.
This warranty defines the obligations and liability of WOLF STEELLtd. with respect to the CONTINENTAL gas fireplace and any other warranties expressed or implied with respect to this
product, its components or accessories are excluded.
WOLF STEEL Ltd. neither assumes, nor authorizes any third party to assume, on its behalf, any other liabilities with respect to the sale of this product. WOLF STEEL Ltd. will not be responsible
for: over-firing, downdrafts, spillage caused by environmental conditions such as rooftops, buildings, nearby trees, hills, mountains, inadequate vents or ventilation, excessive venting
configurations, insufficient makeup air, or negative air pressures which may or may not be caused by mechanical systems such as exhaust fans, furnaces, clothes dryers, etc.
Any damages to fireplace, combustion chamber, heat exchanger, brass trim or other component due to water, weather damage, long periods of dampness, condensation, damaging
chemicals or cleaners will not be the responsibility of WOLF STEEL Ltd.
The bill of sale or copy will be required together with a serial number and a model number when making any warranty claims from your authorized dealer. The warranty registration card
must be returned within fourteen days to register the warranty.
WOLF STEEL Ltd. reserves the right to have its representative inspect any product or part thereof prior to honouring any warranty claim.
ALL SPECIFICATIONSAND DESIGNSARE SUBJECTTO CHANGE WITHOUT PRIOR NOTICE DUE TO ON-GOING PRODUCT IMPROVEMENTS. CONTINENTAL® IS AREGISTERED
TRADEMARK OF WOLF STEELLTD. PATENTS U.S. 5.303.693.801 - CAN. 2.073.411, 2.082.915. © WOLF STEELLTD.
W415-0224 / D / 01.15.04
Download from Www.Somanuals.com. All Manuals Search And Download.
4
GENERAL INFORMATION
GENERAL INSTRUCTIONS
THIS GAS FIREPLACE INSERT SHOULD BE INSTALLED FOR YOUR SATISFACTION, THIS FIREPLACE INSERT
AND SERVICED BY A QUALIFIED INSTALLER to con- HAS BEEN TEST-FIRED TO ASSURE ITS OPERATION
form with local codes. Installation practices vary from re- AND QUALITY!
gion to region and it is important to know the specifics that Minimum inlet gas supply pressure is 4.5 inches water
apply to your area,
for example: in Massachusetts State:
column for natural gas and 11 inches water column for
propane. Maximum inlet gas pressure is 7 inches water
column for natural gas and 13 inches water column for
propane. Manifold pressure under flow conditions is 3.5
inches water column for natural gas and 10 inches water
column for propane. When the fireplace is installed at el-
evations above 4,500ft, and in the absence of specific rec-
ommendations from the local authority having jurisdiction,
the certified high altitude input rating shall be reduced at
the rate of 4% for each additional 1,000ft.
• The fireplace damper must be removed or welded in the open
position prior to installation of a fireplace insert or gas log.
• The appliance off valve must be a “T” handle gas cock.
• The flexible connector must not be longer than 36 inches.
• The appliance is not approved for installation in a bedroom or
bathroom unless the unit is a direct vent sealed combustion
product.
• WARNING: This product must be installed by a licensed plumber
or gas fitter when installed within the commonwealth of
Expansion / contraction noises during heating up and cool-
ing down cycles are normal and to be expected.
Massachusetts.
In absence of local codes, install to the current CAN1-
B149 Installation Code in Canada or to the National Fuel
Gas Code, ANSI Z223.1, and NFPA 54 in the United
States. Mobile home installation must conform with local
codes. In the absence of local codes, install to the current
standard for gas equipped mobile housing CAN/CSA
Z240 MH Series in Canada or the manufactured home
construction and safety standard, Title 24 CFR, part 3280,
or the Fire Safety Criteria for manufactured home installa-
tions, Sites and Community Standard ANSI/NFPA 501A in
the United States.
Maximum input is 24,000 BTU/hr for natural gas and pro-
pane. Maximum output for natural gas and propane is
20,400 BTU/hr at an efficiency of 85% with the fan on. Maxi-
mum A.F.U.E. (annual fuel utilization efficiency) rating is
79 % for natural gas and propane. This fireplace insert is
not approved for closet or recessed installations. It is ap-
proved for bathroom, bedroom and bed-sitting room in-
stallations and is suitable for mobile homes. The natural
gas model is suitable for installation in a mobile home that
is permanently positioned on its site and fuelled with natu-
ral gas.
Purge all gas lines with the glass door of the fireplace
insert opened. Assure that a continuous gas flow is at
the burner before closing the door.
This insert must be recessed into a vented noncombus-
tible wood-burning fireplace (prefabricated or masonry)
only. The minimum fireplace opening size in which the
heater is to be installed is:
Under extreme vent configurations, allow several min-
utes (5-15) for the flame to stabilize after ignition.
HEIGHT
WIDTH
DEPTH
14½
25
11
inches
inches
inches
The fireplace insert and its individual shutoff valve must be
disconnected from the gas supply piping system during
any pressure testing of that system at test pressures in
excess of 1/2 psig (3.5 kPa). The fireplace insert must be
isolated from the gas supply piping system by closing its
individual manual shutoff valve during any pressure test-
ing of the gas supply piping system at test pressures
equal to or less than 1/2 psig (3.5 kPa).
The minimum allowable chimney flue size is 6" round.
The minimum distance, from the bottom of a combustible
mantle projecting 3" maximum from the wall to the top of
the aluminium trim, is 3".
CARE OF GLASS, AND PLATED PARTS
Do not use abrasive cleaners to clean these parts. Buff
lightly with a clean dry cloth.
A 1/8 inch NPT plug, accessible for test gauge connection,
must be installed immediately upstream of the gas supply
connection to the fireplace insert.
The glass is 3/16" ceramic glass available from your
Continental / Wolf Steel Ltd. dealer. DO NOT SUBSTITUTE
MATERIALS. Clean the glass after the first 10 hours of op-
eration with a recommended gas fireplace glass cleaner.
Thereafter clean as required. DO NOT CLEAN GLASS
WHEN HOT! If the glass is not kept clean permanent
discolouration and / or blemishes may result.
The fireplace insert must be electrically connected and
grounded in accordance with local codes. In the absence
of local codes, use the current CSA C22.1 CANADIAN
ELECTRICAL CODE in Canada or the ANSI/NFPA 70-1990
NATIONAL ELECTRICAL CODE in the United States. The
blower power cord must be connected into a properly
grounded receptacle. The grounding prong must not be
removed from the cord plug.
W415-0224 / D / 01.15.04
Download from Www.Somanuals.com. All Manuals Search And Download.
5
INSTALLATION
Clean out ashes from the inside of the wood-burning fire-
Provide adequate ventilation air.
place. Make sure that the chimney and wood-burning fire-
place are in a clean and sound condition and constructed
of non-combustible materials. If necessary have any re-
pair work done by a qualified person before installing the
insert. Remove the existing fireplace damper or lock into
an open position.
Using screws, attach the fireplace warning tag
(W385-0199) to the inside of the firebox of the fireplace into
which the insert is being installed.
Provide adequate accessibility clearance for
servicing and operating the fireplace insert.
Never obstruct the front opening of the fire-
place insert.
Objects placed in front of the fireplace must
be kept a minimum of 48" away from the
front face of the unit.
FIGURES1a-c
WARNING: THIS FIREPLACE HAS BEEN CONVERTED FOR USE WITH
A
GAS
FIREPLACE INSERT ONLY AND CANNOT BE USED FOR BURNING WOOD OR SOLID
FUELS UNLESS ALL ORIGINAL PARTS HAVE BEEN REPLACED AND THE FIREPLACE
IS RE-APPROVED BY THE AUTHORITY HAVING JURISDICTION.
ATTENTION: CE FOYER A ETE CONVERTI AFIN D'ETRE UTILISE SEULEMENT COMME
FOYER ENCASTRE AU GAZ ET NE PEUT ETRE UTILSE POUR BRULER DU BOIS OU
TOUT AUTRE COMBUSTIBLE SOLIDE, SANS QUE TOUTES LES PIECES ORIGINALES
AIENT ETE REMPLACEES ET QUE LE FOYER SOIT APPROUVE DE NOUVEAU PAR
LES AUTORITES AYANT JURIDICTION.
W385-0199
The sheet-metal parts of the fireplace, in which the gas
fireplace insert is to be installed, must not be cut.
If the wood-burning factory-built fireplace has no gas
access hole(s) provided, an access hole of 1½ inch or
less may be drilled through the lower sides or bottom
of the fireplace in a proper workman like manner. This
access hole must be plugged with non-combustible in-
sulation after the gas supply line has been installed.
Ensure that existing chimney cleanouts fit properly.
3 SIDED BACKER PLATE
The refractory, glass doors, screen rails, screen mesh
and log grates may be removed from the fireplace be-
fore installing the gas fireplace insert.
Smoke shelves, shields and baffles may be removed if
attached by mechanical fasteners.
The ventilation openings in the fireplace may be ob-
structed by the backer plates, aluminium trim etc. but
these parts are not to be applied so as to have an air-
tight seal.
3 & 4 SIDED BACKER PLATES - SIDE VIEWS
4 SIDED BACKER PLATE - FRONT VIEW
TOP VIEW
W415-0224 / D / 01.15.04
Download from Www.Somanuals.com. All Manuals Search And Download.
6
2. Gently stretch the liners to the required lengths and in-
sert into the chimney. Place the terminal onto the top of the
INSERT VENT CONNECTION
Move the insert close to its final position inside the wood- chimney cap and fit the flashing plate to suit. Make weather
burning fireplace. This unit is equipped with 6 levelling tight by sealing with caulking (not supplied) and fasten to
screws located as follows: two are on either side of the the chimney with screws and plugs (not supplied)
circulation blower on the rear panel; four are located front 3. INSIDE: Attach and secure the flex liners to the vent
and back on either side beneath the log support. Level connection assembly using the same procedure as be-
using four of the levelling screws. See Figure 1a. Levelling fore, ensuring that the marked exhaust liner is attached
the unit will eliminate rocking or excessive noise when the to the exhaust collar.
fan is in operation. Once the unit is level, move it partially
into place within the fireplace to allow for all connections to
be made. It is not practical to level the insert once the it has
been installed. Determine the required depth prior to in-
stalling the unit and adjust the four levelling screws accord-
ingly.
FIGURE 3
FIGURE 4
CHIMNEY CONNECTION
Chimney installation must conform to both national and
local code requirements. The chimney must be lined with
one 2" or 3" diameter liner for intake and one 3" diameter
liner for exhaust. The minimum and maximum vent lengths
are 10 and 35 feet respectively. Recommended Continental
kits come in 3 lengths: While the liners must be continuous
from the fireplace to the terminal, to achieve the needed
length, they may be coupled, using an aluminium coupler,
provided installation is sealed & secured.
1-2" & 1-3" DOUBLE PLY ALUMINUM LINER-INLET AND EXHAUST &
2-3" TO 2" REDUCER:
GDI-2320KT
GDI-2325KT
GDI-2335KT
VENT KIT 20FT
VENT KIT 25FT
VENT KIT 35FT
2-3" DOUBLE PLY ALUMINUM LINER-INLET AND EXHAUST:
4. Detach the two screws from the back of the firebox and
remove the panel, as illustrated.
GDI-320KT
GDI-325KT
GDI-335KT
VENT KIT 20FT
VENT KIT 25 FT
VENT KIT 35 FT
STUDS
We recommend that exhaust vents that pass through
unheated spaces, such as a garage or attic, be
wrapped in a protective sleeve to minimize condensa-
tion and reverse flow symptoms. See Trouble Shooting
for details.
This unit is approved for use with a 2" liner for air intake
and a 3" liner for exhaust. For best performance,
however, it is recommended to use two 3" liners.
If a 2" liner is used for the intake, it is necessary to
adjust the primary air shutter. See "Air Shutter Settings"
VENT CONNECTOR
EXTENSION
RESTRICTOR
PLATE
on page 11.
FIGURE 2
1. OUTSIDE: Slip one
end of a liner a minimum
of 2" over one of the
collars of the terminal. Se-
cure using 3 screws. Then
seal the joint and screw
heads with high tempera-
ture sealant. Repeat with
the other liner.
FIGURE5a-b
5. Reaching in through the insert, manoeuvre the vent con-
nection assembly through the openings in the firebox top,
taking care not to damage the gasket. In case of a low
ceiling fireplace, the extension should be removed and
reinstalled after the vent connection is secured to the fire-
box. Attach the restrictor plate to the centre stud and se-
cure the assembly using the three studs and ¼-20 hex
nuts.
NOTE: We recommend that the other end of the exhaust
liner be marked to eliminate the exhaust liner being con-
nected to the intake collar at the unit.
W415-0224 / D / 01.15.04
Download from Www.Somanuals.com. All Manuals Search And Download.
7
WALL SWITCH / THERMOSTAT
GAS INSTALLATION
Install suitable supply piping connection to the /8" flex
3
For ease of accessibility, an optional remote wall switch
or millivolt thermostat may be installed in a convenient
location. Route 2-strand solid core millivolt wire from
the gas fireplace insert to the wall switch / millivolt ther-
mostat. The recommended maximum lead length de-
pends on the wire size:
connector supplied (as per local gas codes).
FIGURE 6
WIRE SIZE
14gauge
16gauge
18gauge
MAX. LENGTH
100 feet
60 feet
The insert may now be
pushed into its final posi-
tion inside the wood-burn-
ing fireplace. Secure the in-
sert to the fireplace using
perforated strapping at-
40 feet
Do not connect either the wall switch, thermo-
stat or gas valve to electricity (110 VOLTS).
S E C U R I N G
tached to the two securing
HOLES
holes on either side of the
unit as shown. We recom-
mend that the trim be in-
stalled before the unit is
placed into its final position.
FIGURE 7
FINISHING
In order to close off the fireplace opening or if the opening
is larger than the 3- or 4-sided aluminium extrusion trim
kits, it is recommended to reduce the opening using a non-
combustible material such as ceramic tile, marble, etc or
the GIZBP6-3 or GIZBP6-4 backer plate kits. The outside
edge of the backer plate is finished off with gold trim in-
cluded in each kit. A deluxe flashing kit complete with mar-
quis trim may also be used to complete the installation.
These flashing and trim combinations are available in 6
and 9 inch widths as well as many finishes to accent any
room decor. Mounting brackets, GIZBRKT, are required to
install the deluxe flashing. Detailed installation instructions
are included with each kit.
FIRE VIEWING DOOR
VALVE
CONTROL
DOOR
FIGURE 8
FIGURE 10
SLIDE TO
ADJUST
FIGURE 11
If this unit is being installed into an existing wood burning,
zero clearance fireplace, then be aware of this precaution:
Any circulation air opening may be covered (with non-
combustible material) but not sealed!
LOOSEN
SCREWS
ALUMINIUM EXTRUSION TRIM KIT
INSTALLATION
The insert can be equipped
with either a 3- or 4-sided
trim kit to finish off the fire-
place opening. Slide the trim
assembly over the keyholes
(2 per side) and drop into
place. If installing the op-
tional 3- or 4-sided backer
plate (GIZBP6-3 or GIZBP6-
4), it must be hung prior to
the trim kit installation us-
To adjust the trim: If the mitre is out of alignment, open
each side and loosen the two screws at either side trim
hinge. Slide the trim up or down to adjust and re-tighten
screws. There is also a very slight in/out adjustment that
can be made.
Note: Since the side panels open and close, to access
the controls, a gap is necessary at the mitre joint.
ing the same keyholes.
The top trim piece has an adjustable securing bracket
which enables the trim to be secured to the firebox shell.
FIGURE 9
W415-0224 / D / 01.15.04
Download from Www.Somanuals.com. All Manuals Search And Download.
8
LOG PLACEMENT
DOOR INSTALLATION
Positioning the logs improperly will cause flame im- Place the door into the two lower door brackets, and se-
pingement and carboning.
cure at the top of the unit with two #10-24 machine screws.
PHAZERTM logs and glowing embers, exclusive to Continental
Fireplaces, glow when exposed to direct flame and provide
a unique and realistic glowing effect that is different in every
installation. Take the time to carefully position the glowing
embers for a maximum glowing effect. Use only certified
PHAZERTM logs available from your Continental / Wolf Steel
Ltd. dealer.
FIGURE 16
1. Place the rear log (#1) onto the two log supports and
against the air intake pipe.
FIGURE 12
#1
LOWER DOOR BRACKET
2. Position logs #2 and #3 against the grate posts and line up
the studs located on the burner with the holes on the bottom
of the logs. Keep slightly back of the front row of ports.
MANTLE CLEARANCE
This can vary according to the mantle depth. Use the graph
to help evaluate the clearance needed.
FIGURE 13
FIGURE 17
#2
#3
M H
E
I
A
N
3. Fit the centre log (#4) into place behind log #3 and into
the pocket provided on the back log.
FIGURE 14
T G
L H
T
E
#4
MANTLE WIDTH
LOGO PLACEMENT
FIGURE 15
Remove the backing of the logo supplied and place on the
glass viewing door, as indicated.
GLOWING EMBERS
4. Tear the glowing embers into pieces and place along
the front row of ports covering all of the burner area in front
of the logs. Care should be taken to shred the embers into
thin, small irregular pieces as only the exposed edges of
the fibre hairs will glow. The ember material will only glow
when exposed to direct flame; however, care should be
taken to not block the burner ports. Blocked burner ports
can cause an incorrect flame pattern, carbon deposits and
delayed ignition.
½”
LOGO
½”
Log colours may vary. During the initial use of the fireplace,
the colours will become more uniform as colour pigments
FIGURE 18
burn in during the heat activated curing process.
W415-0224 / D / 01.15.04
Download from Www.Somanuals.com. All Manuals Search And Download.
9
OPERATION / MAINTENANCE
When lit for the first time, the fireplace will emit a slight
odour for a few hours. This is a normal temporary con-
The on-off switch is located behind the left side control dition caused by the "burn-in" of paints and lubricants
OPERATING INSTRUCTIONS
door.
used in the manufacturing process and will not occur
again. Simply open a window to sufficiently ventilate
the room. After extended periods of non-operation such
as following a vacation or a warm weather season, the
fireplace may emit a slight odour for a few hours. This is
caused by dust particles in the heat exchanger burning
off. Open a window to sufficiently ventilate the room.
PURGE THE GAS LINE WITH THE GLASS DOOR OPEN.
Purge all gas lines with the glass door open. Assure
that a continuous gas flow is at the burner before clos-
ing the door. Allow several minutes (5-15) for the flame
to stabilize after ignition.
Do not operate the main burner of the in-
sert with the door removed.
WHAT TO DO IF YOU SMELL GAS:
FOR YOUR SAFETY READ BEFORE LIGHTING:
• Turn off all gas to the fireplace.
• Open windows.
A. This fireplace is equipped with a pilot which must be lit
by hand. While following these instructions exactly.
B. Before operating smell all around the fireplace area for
gas and next to the floor because some gas is heavier
than air and will settle on the floor.
C. Use only your hand to turn the gas control knob. Never
use tools. If the knob will not turn by hand, do not try to
repair it. Call a qualified service technician. Force or at-
tempted repair may result in a fire or explosion.
D. Do not use this fireplace if any part has been under water.
Immediately call a qualified service technician to inspect
the fireplace and replace any part of the control system
and any gas control which has been under water.
• Do not try to light any appliance.
• Do not touch any electric switch; do not use any phone in
your building.
• Immediately call your gas supplier from a neighbour's
phone. Follow the gas supplier's instructions.
• If you cannot reach your gas supplier, call the fire depart-
ment.
FIGURE 19
FLAME ADJUSTMENT
KNOB
ON/OFF KNOB
FIGURE 20
7. Turn gas knob counter-clockwise
to pilot.
LIGHTING INSTRUCTIONS
8. Depress slightly and hold gas knob while lighting the pilot
with the push button ignitor. Keep knob depressed for one
minute, then release. If pilot does not continue to burn, re-
peat steps 3 through 7.
When lighting and re-lighting, the gas knob cannot be turned
from pilot to off unless the knob is depressed slightly.
1. Stop! Read the above safety information on this label.
2. Turn off all electric power to the fireplace.
9. With pilot lit, depress and turn gas knob counter-clock-
wise
to on.
3. Turn the gas knob clockwise
to off.
10. If equipped with flame adjustment valve, push and turn
knob to high.
11. If equipped with remote on-off switch/thermostat, main
burner may not come on when you turn valve to on. Remote
switch must be in the on position to ignite burner.
12. Turn on all electric power to the fireplace.
4. Wait five (5) minutes to clear out any gas. If you smell gas
including near the floor. Stop! Follow "B" in the above safety
information on this label. If you don't smell gas go the next step.
5. If fireplace is equipped with flame adjustment valve turn
clockwise to off.
6. Find pilot located in front of back log.
TO TURN OFF GAS
2. Push in gas control knob slightly and turn clockwise
to off. Do not force.
1. Turn off all electrical power to the unit if service is to be
performed.
2. Keep the control compartment, logs, burner, air shutter open-
ing and the area surrounding the logs clean by vacuuming
or brushing, at least once a year.
3. Check to see that all burner ports are burning. Clean out
any of the ports which may not be burning or are not burning
properly.
MAINTENANCE
TURN OFF THE GAS AND UNPLUG ELECTRICAL POWER
BEFORE SERVICING THE FIREPLACE INSERT!
CAUTION: Label all wires prior to disconnection when serv-
icing controls. Wiring errors can cause improper and dan-
gerous operation. Verify proper operation after servicing. 4. Check to see that the pilot flame is large enough to engulf
This insert and its venting system should be inspected
before use and at least annually by a qualified service per-
the thermocouple on one leg and reaches toward the burner
on the other leg.
son. The fireplace area must be kept clear and free of 5. Replace the cleaned logs.
combustible materials, gasoline or other flammable va- 6. Check to see that the main burner ignites completely on all
pours and liquids. The flow of combustion and ventilation
air must not be obstructed.
1. In order to properly clean the burner and pilot assembly,
remove the logs exposing both assemblies.
openings when the gas knob for the burner is turned on. A
5-10 second total light-up period is satisfactory. If ignition
takes longer, consult your Continental dealer/distributor.
7. Check that the door gasketing is not broken or missing.
Replace if necessary.
W415-0224 / D / 01.15.04
Download from Www.Somanuals.com. All Manuals Search And Download.
10
REPLACEMENT BLOWER INSTALLATION
The Napoleon gas fireplace insert comes standard with a
blower, a heat sensor, variable on/off speed control and a
power cord. Because the blower is thermally activated,
when turned on, it will automatically start approximately 15
minutes after lighting the fireplace and will run for approxi-
mately 30 minutes after the fireplace has been turned off.
Use of the fan increases the output of heat. Air, drawn in
through the lower slot, is driven up the back of the firebox,
and exhausted as hot air through the upper slot.
THERMODISC
B R A C K E T
ASSEMBLY
BLOWER
WIRES
FIGURE 24
4. Disconnect the two blower wires. Remove the blower
bracket secured with one wing nut and lock washer.
For thermodisc replacement: Remove the "Z" shaped
mounting bracket secured to the firebox wall to the left of
the blower. Remove the thermodisc from the bracket and
replace.
FIGURE 21
B
C
1. Turn off the electrical power and the gas supply to the
fireplace insert.
2. Remove the fire viewing door. Remove the logs.
A
FIGURE 22
FIGURE 25
FIGURE 26
5. Replace the blower using the existing bracket. Slide the
vibration reducing pad (A) into the clip (C) and up against
the threaded stud (B) at the other end. The blower must be
able to be positioned entirely onto the pad.
Slide the blower into the clip (C). Secure to the threaded
stud using the existing lock washer and wing nut. Ensure
3. Detach the two screws from the back of the firebox and that the blower does not touch the fireplace base or the
firebox.
remove the panel, as illustrated.
6. Reconnect the two wires. Holding the replacement gas-
ket in place, reattach the blower access door and panel.
Replace the logs. Re-install the fire viewing door.
7. Turn the gas supply and electricity back on.
BLOWER ACCESS DOOR
Drywall dust will penetrate into the blower bearings caus-
ing irreparable damage and must be prevented from
coming into contact with the blower or its compartment.
Any damage resulting from this condition is not cov-
ered by the warranty policy.
FIGURE 23
4. Remove the blower access door held on with the re-
maining 8 screws. Replace the blower access door gas-
ket when changing the blower.
W415-0224 / D / 01.15.04
Download from Www.Somanuals.com. All Manuals Search And Download.
11
ADJUSTMENTS
PILOT BURNER ADJUSTMENT
VENTURI ADJUSTMENT
Remove the pilot screw cap. Adjust the pilot screw to pro-
vide properly sized flame. Turn in a clockwise direction to
reduce the gas flow. Replace the pilot screw cap.
This unit is approved for use with a 2" liner for air intake
and a 3" liner for exhaust. For best performance, however,
it is recommended to use two 3" liners.
Air shutter settings will differ depending on the liner sys-
tem used. Use the charts below to determine the correct
air shutter setting:
FIGURE 27
3"/ 3" LINER SYSTEM
NG
LP
1
"
16
/
3
"
/
16
AIR SHUTTER SETTING
2"/ 3" LINER SYSTEM
NG
LP
1 "
/
8
5
"
/
16
AIR SHUTTER SETTING
Closing the air shutter will cause a more yellow flame, but
can lead to carboning. Opening the air shutter will cause a
more blue flame, but can cause flame lifting from the burner
ports. The flame may not appear yellow immediately; allow
15 to 30 minutes for the final flame colour to be estab-
lished.
Air shutter adjustment
must only be done by a
qualified gas installer!
FIGURE 28
VENT RESTRICTION
FIGURE 30
Some vent configurations may display a very active flame. If
this appearance is not desirable, the vent exit may be re-
stricted using the restrictor plate shown in FIGURE 6b. Bend
the flap up as shown to reduce the velocity of the exhaust
gases, slowing down the flame pattern and creating a more
traditional appearance.
HELPFULHINT:
A mirror will let you see the opening of
the air shutter without removing the
burner. Scribe a line along the venturi
tube and air shutter cap. Open or close
according to the original opening by
using the scribed line as your datum.
FIGURE 29
W415-0224 / D / 01.15.04
Download from Www.Somanuals.com. All Manuals Search And Download.
12
REPLACEMENTS
Contact your dealer for questions concerning prices and
When ordering replacement parts always give the follow-
availability of replacement parts. Normally all parts can be
ordered through your Continental dealer or distributor.
ing information:
1. MODEL & SERIAL NUMBER OF FIREPLACE
2. INSTALLATION DATE OF FIREPLACE
3. PART NUMBER
4. DESCRIPTION OF PART
5. FINISH
* IDENTIFIES ITEMS WHICH ARE NOT ILLUSTRATED. FOR
FURTHER INFORMATION, CONTACT YOUR CONTINENTAL
DEALER.
FOR WARRANTY REPLACEMENT PARTS , A PHOTOCOPY OF THE ORIGINAL INVOICE WILL BE REQUIREDTO HONOUR THE CLAIM.
REPLACEMENT PARTS
ACCESSORIES:
1
1
2
3
3
4
4
5
5
6
7
8*
9*
10
11
12
13
14
W725-0039
RBT SHAW VALVE - NG
RBT SHAW VALVE - LP
BURNER
#42 BURNER ORIFICE - NG
#53 BURNER ORIFICE - LP
PILOT ASSEMBLY - LP
PILOT ASSEMBLY - NG
PILOT INJECTOR - NG
PILOT INJECTOR - LP
THERMOCOUPLE
THERMOPILE
HIGH TEMPERATURE SEALANT
PIEZO IGNITOR
LOG SET
REAR LOG
RIGHT LOG
LEFT LOG
CENTER LOG
GLOWING EMBERS
BLOWER
CONTINENTAL LOGO
DOOR GLASS C/W GASKET
DOOR FRAME
DOOR C/W GLASS
BLOWER ACCESS GASKET
MAGNETIC CLOSURE
ON/OFF SWITCH
31*
32*
32*
33*
34
35*
35*
36*
37*
38*
38*
38*
39
39
39
40
40
41
41
41
41
41
41
41
41
41
41
41
41
41
41
42*
43
43
43
43
44*
45
45
W690-0001
W660-0010
W660-0011
GD660
MILLIVOLT THERMOSTAT
REMOTE CONTROL - ADVANTAGE
REMOTE CONTROL - ADVANTAGE PLUS
REMOTE WALL SWITCH C/W 20FT WIRE
DECORATIVE BRICK PANELS
CONVERSION KIT - NG-LP
CONVERSION KIT - LP-NG
3 SIDED BACKER PLATE C/W ACCENT TRIM
4 SIDED BACKER PLATE C/W ACCENT TRIM
ALUMINIUM EXTRUSION - MATTE BLACK
ALUMINIUM EXTRUSION - POLISHED BLACK
ALUMINIUM EXTRUSION - POLISHED BRASS
ALUMINIUM EXTRUSION - MATTE BLACK
ALUMINIUM EXTRUSION - POLISHED BLACK
ALUMINIUM EXTRUSION - POLISHED BRASS
UPPER DOOR TRIM - BRASS
W725-0040
W100-0068
W455-0017
W455-0059
W010-0800
W010-0801
W455-0069
W455-0067
W680-0005
W680-0004
W573-0008
W357-0001
GL-631
GI-790KT
W175-0162
W175-0192
GIZBP6-3
GIZBP6-4
GIZTRM3
GIZTRM3-K
GIZTRM3-B
GIZTRM4
GIZTRM4-K
GIZTRM4-B
GIZUT-B
GIZUT-G
GI-900K6
GI-900B6
GI-900AB6
GI-900SS6
GI-909S6
GI-909K6
GI-909F6
GI-900K9
GI-900B9
GI-900AB9
GI-900SS9
GI-909S9
GI-909K9
GI-909F9
GIZBRKT
CISK-A
W135-0136
W135-0138
W135-0137
W135-0139
UPPER DOOR TRIM - GOLD
6" DELUXE FLASHING W MARQUIS TRIM - BLACK
6" DELUXE FLASHING W MARQUIS TRIM - POLISHED BRASS
6" DELUXE FLASHING W MARQUIS TRIM - ANTIQUE BRASS
6" DELUXE FLASHING W MARQUIS TRIM - BRUSHED STAINLESS STEEL
6" DELUXE FLASHING W MARQUIS TRIM - PORCELAIN ALMOND
6" DELUXE FLASHING W MARQUIS TRIM - PORCELAIN BLACK
6" DELUXE FLASHING W MARQUIS TRIM - PORCELAIN GREEN
9" DELUXE FLASHING W MARQUIS TRIM - BLACK
9" DELUXE FLASHING W MARQUIS TRIM - POLISHED BRASS
9" DELUXE FLASHING W MARQUIS TRIM - ANTIQUE BRASS
9" DELUXE FLASHING W MARQUIS TRIM - BRUSHED STAINLESS STEEL
9" DELUXE FLASHING W MARQUIS TRIM - PORCELAIN ALMOND
9" DELUXE FLASHING W MARQUIS TRIM - PORCELAIN BLACK
9" DELUXE FLASHING W MARQUIS TRIM - PORCELAIN GREEN
MOUNTING BRACKETS (REQUIRED FOR THE 900 SERIES FLASHING KITS)
CAST IRON SURROUND KIT - PAINTED BLACK
CAST IRON SURROUND KIT - PORCELAIN ENAMEL BLACK
CAST IRON SURROUND KIT - PORCELAIN ENAMEL MAJOLICA BROWN
CAST IRON SURROUND KIT - PORCELAIN ENAMEL MAJOLICA GREEN
ADAPTOR KIT FOR CAST IRON SURROUND
ANDIRON - PAINTED BLACK
15* W361-0016
16 GZ552
17* W385-0131
18* W010-0804
19* W225-0095
20
W010-0802
21* W290-0063
22* W430-0013
23* W660-0009
24* W690-0002
25* W380-0002
26* KB35
THERMODISC
VARIABLE SPEED SWITCH KNOB
VARIABLE SPEED SWITCH
RESTRICTOR BRACKET
27
W080-0451
TERMINAL KITS
CISKK-A
CISKN-A
CISKF-A
AK-4
ANI-K
ANI-G
28
GDI-223
TERMINAL KIT
VENT KITS
1-2" & 1-3" DOUBLE PLY ALUMINUM LINER-INLET AND
EXHAUST & 2-3" TO 2" REDUCER:
ANDIRON - GOLD PLATED
29* GDI-2320KT
29* GDI-2325KT
29* GDI-2335KT
VENT KIT 20FT
VENT KIT 25FT
VENT KIT 35FT
2-3" DOUBLE PL Y ALUMINUM LINER-INLET AND
EXHAUST:
30* GDI-320KT
30* GDI-325KT
30* GDI-335KT
VENT KIT 20FT
VENT KIT 25 FT
VENT KIT 35 FT
W415-0224 / D / 01.15.04
Download from Www.Somanuals.com. All Manuals Search And Download.
13
W415-0224 / D / 01.15.04
* WARNING: This is a fast acting thermocouple. It is an integral safety component. Replace only
with a fast acting thermocouple supplied by Wolf Steel Ltd.
Download from Www.Somanuals.com. All Manuals Search And Download.
14
TROUBLE SHOOTING GUIDE
BEFORE ATTEMPTING TO TROUBLESHOOT, PURGE YOUR UNIT AND INITIALLY LIGHT THE PILOT AND THE MAIN BURNER WITH THE GLASS DOOR REMOVED.
SYMPTOM
PROBLEM
TEST SOLUTION
No spark at pilot burner
- check if pilot can be lit by a match
Pilot will not light.
- check that the wire is connected to the push button ignitor.
- check if the push button ignitor needs tightening.
- replace the push button ignitor.
- spark gap should be 0.150" to 0.175" (5/32" to 11/64" approx.)
from the electrode tip and the pilot burner.
Spark gap is incorrect
No gas at the pilot burner
- check that the manual valve is turned on.
- check the pilot orifice for blockage.
- replace the valve.
- call the gas distributor.
Out of propane gas.
- fill the tank.
- purge the gas line with the glass door open.
Pilot goes out when
the gas knob is re-
leased.
System is not correctly purged.
Out of propane gas
- fill the tank.
Pilot flame is not large enough
- turn up the pilot flame.
Pilot flame is not engulfing the - turn up pilot flame.
thermocouple.
-
replace pilot assembly.
- loosen and tighten thermocouple.
- clean thermocouple and valve connection.
- replace thermocouple.
Thermocouple shorting.
- replace valve.
Faultly thermocouple.
Faulty valve.
- replace.
- replace.
- remove stoppage in orifice.
- replace.
Pilot burning; no gas Main burner orifice is plugged.
to main burner; gas
knob is on 'HI'; wall
Faulty themostat or switch.
switch / thermostat is
Faulty thermopile.
- connect a jumper wire across the wall switch terminals; if
main burner lights, replace thermostat.
on.
- disconnect the switch wires & connect a jumper wire across
terminals 1 & 3; if the main burner lights, check the wires for
defects and / or replace wires.
Faulty valve.
- replace.
-
turn on all gas appliances and see if pilot flame flutters,
Gas piping is undersized.
Pilot goes out while
standing; Main burner
is in 'OFF' position.
diminishes or extinguishes, especially when main burner ig-
nites. Monitor supply pressure.
- check if supply piping size is to code. Correct all undersized
piping.
Pilot flame is not large enough - turn up pilot flame.
or not engulfing the thermopile. - replace pilot assembly.
Main burner goes out;
pilot stays on.
- clean thermopile and thermopile connection to valve.
Thermopile shorting
Remote wall switch wire is too
long, too much resistance in
the system
- shorten wire to correct length or wire gauge.
- replace
Faulty thermostat or switch
W415-0224 / D / 01.15.04
Download from Www.Somanuals.com. All Manuals Search And Download.
15
SYMPTOM
PROBLEM
TEST SOLUTION
REFER TO "MAIN BURNER GOES OUT; PILOT STAYS ON"
Main burner goes out;
pilot goes out.
Vent re-circulating
- check joint seals and installation.
Thermocouple shorting or
faulty.
- loosen and tighten thermocouple
- clean thermocouple and valve connection.
- replace thermocouple.
- replace valve.
Vent is reversing
- check all venting and insert seals.
- check that door is properly sealed. If the insert is allowed to
burn with the door off when purging the unit, exhaust products
may escape through the air intake pipe and reverse the venting
action. Let the unit cool down to correct the reversed venting
action.
Exhaust
fumes
- check all seals.
Fireplace is spilling.
smelled in room,
headaches.
Carbon is being de- Air shutter has become
posited on glass, blocked
- ensure air shutter opening is free of lint or other obstruc-
tions.
logs or combustion
chamber surfaces.
Flame is impinging on the - check that the logs are correctly positioned.
logs or combustion chamber. - open air shutter to increase the primary air.
- check the input rate: check the manifold pressure and orifice
size as specified by the rating plate values.
- check that the door gasketing is not broken or missing and
that the seal is tight.
- check that both vent liners are free of holes and well sealed at
all joints.
- check and adjust air shutter to correspond with the fuel type
and air intake size.
Air shutter is not set to specifi-
cations.
Main burner flame is Blockage in vent.
a blue, lazy, transpar-
- remove blockage. In really cold conditions, ice buildup may
occur on the terminal and should be removed as required.
ent flame.
- vent liners are reversed. Refer to Figure 2.
- check all venting and insert seals.
Incorrect installation.
Sulphur from fuel is being de- - clean the glass with a recommended gas fireplace glass
posited on glass, logs or com- cleaner. DO NOT CLEAN GLASS WHEN HOT.
White / grey film
forms.
bustion chamber surfaces.
If deposits are not cleaned off regularly, the glass may be-
come permanently marked.
W415-0224 / D / 01.15.04
Download from Www.Somanuals.com. All Manuals Search And Download.
16
W415-0224 / D / 01.15.04
Download from Www.Somanuals.com. All Manuals Search And Download.
|