MOD HUB series
A Line of Modular Active Hubs for ARCNET®
Local Area Networks
Expansion Modules
Installation Instructions
#TD471100-0II
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
This document provides instructions for installing and removing
expansion modules to be used in the MOD HUB series of
modular ARCNET active hubs. More detailed information
regarding the MOD HUB Series can be obtained by referring to
Contemporary Controls’ MOD HUB Series User Manual.
CABLING CONSIDERATIONS
The MOD HUB Series is a line of modular active hubs for
ARCNET local area networks. These hubs support several
cabling types including coaxial, twisted-pair and glass fiber
optics.
As far as topology is concerned, each MOD HUB expansion
module is designed for use in star or distributed star
configurations. Expansion modules can be used to extend the
length of coaxial and twisted-pair bus segments by connecting
the expansion module at the end of bus segments.
The cabling types supported by the MOD HUB Series are listed
on the following page with their corresponding model numbers.
TD471100-0II
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Model Number
EXP-CXS
Description
4-port coaxial star expansion module
Coax/1300 nm fiber expansion module
EXP-CXS/FG3-ST
EXP-CXS/FOG-SMA 2-port coax/fiber SMA expansion
module
EXP-CXS/FOG-ST
EXP-CXS/485
EXP-CXS/485X
EXP-FOG-SMA
EXP-FOG-ST
EXP-TPS
2-port coax/fiber ST expansion module
2-port coax/485 expansion module
2-port coax/485X expansion module
4-port fiber SMA expansion module
4-port fiber ST expansion module
4-port twisted-pair expansion module
EXP-TPS/CXS
2-port twisted-pair/coax expansion
module
EXP-TPS/FOG-SMA 2-port twisted-pair/fiber SMA expansion
module
EXP-TPS/FOG-ST
2-port twisted-pair/fiber ST expansion
module
EXP-485
4-port DC EIA-485 expansion module
EXP-485/FOG-SMA 2-port 485/fiber SMA expansion module
EXP-485/FOG-ST
EXP-485X
2-port 485/fiber ST expansion module
4-port AC EIA-485 expansion module
EXP-485X/FOG-SMA 2-port 485X/fiber SMA expansion
module
EXP-485X/FOG-ST
2-port 485X/fiber ST expansion module
TD471100-0II
2
Download from Www.Somanuals.com. All Manuals Search And Download.
REMOVING MODULES FROM THE MOD HUB
Before removing the modules from the MOD HUB, turn the unit
off by depressing the power switch located on the front panel of
the MOD HUB. Unplug the power cord from the wall outlet.
Disconnect the cables from the connectors on the module that is
being removed.
Dislodging Modules From The MOD HUB
Loosen the module from the MOD HUB unit by unscrewing
both of the captive screws with your fingers. The captive screws
are located on each end of the module. Loosen the captive
screws until they are unthreaded to the point where they hang
freely from the module.
With your fingers, grasp each of the module's captive screws
and pull the module out of the MOD HUB unit until it is free
from the unit. (If you are removing a blank panel, simply
unscrew the two fasteners.)
INSTALLING MODULES INTO THE MOD HUB
Before installing modules into the MOD HUB, turn the unit off
by depressing the power switch located on the front panel of the
MOD HUB. Unplug the power cord from the wall outlet.
Loading Modules Into The MOD HUB
Remove any of the blank panels or modules being replaced from
the MOD HUB. Unpackage the module to be installed into the
MOD HUB, taking care not to harm the module.
Grasp the module by the faceplate (with the circuitry on the
module facing to the left) and gently place the module into the
empty slot on the MOD HUB. Push the module into the MOD
HUB (you may need to exert some force to seat the module into
position) until the module's face plate is seated against the unit.
TD471100-0II
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Tighten the captive screws on the module panel with your
fingers and fasten them in the locking position.
Attach the cables running from each device in the ARCNET
LAN to the appropriate module connectors on the newly-
installed expansion module.
Refer to the MOD HUB Series User Manual, Chapter 2, to test
the module for proper working operation.
TD471100-0II
4
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDICES
Appendix A–Declaration of Conformity
Applied Council Directives:
Low Voltage Directive 72/23/EEC Council Directive as
amended by Council Directive 93/68/EEC
Electromagnetic Compatibility Directive, 89/336/EEC Council
Directive as amended by Council Directive 92/31/EEC &
Council Directive 93/68/EEC
Standard to which Conformity is Declared
EN 55022:1995 CISPR22: 1993, Class A, Limits and Methods
of Measurement of Radio Disturbance Characteristics of
Information Technology Equipment
EN 55024:1998, Information Technology Equipment —
Immunity Characteristics — Limits and Methods of
Measurement
EN 60950, IEC 950 Safety of Information Technology
Equipment Including Electrical Business Equipment
Manufacturer:
Contemporary Control Systems, Inc.
2431 Curtiss Street
Downers Grove, IL 60515 USA
Authorized Representative:
Contemporary Controls Ltd
Sovereign Court Two
University of Warwick Science Park
Sir William Lyons Road
Coventry CV4 7EZ
UNITED KINGDOM
TD471100-0II
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Type of Equipment:
Industrial local area network modular hub and associated
expansion modules
Directive *
Model
EMC
LVD
MODHUB-16E
MODHUB-16EF
EXP-CXS
EXP-CXS/FG3-ST
EXP-CXS/FOG-SMA
EXP-CXS/FOG-ST
EXP-FOG-SMA
EXP-FOG-ST
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
N/R
N/R
N/R
N/R
N/R
N/R
N/R
N/R
EXP-TPS
EXP-TPS/FOG-ST
* Yes — product is certified to this directive
N/R — this directive is not required for this product
Year of CE Marking (low voltage directive) May 1996
Technical File TD401600-0FA
I, the undersigned, hereby declare that the product(s) specified
above conforms to the listed directives and standards.
George M. Thomas, President
September 15, 2003
TD471100-0II
6
Download from Www.Somanuals.com. All Manuals Search And Download.
|