®
ELITE WEATHERMASTER TENT
MODEL 2000005748
Before you begin
Fig. 6
Curved Ridge Poles with Red Markings in center sleeves
Read all instructions before set up.
•
Select a level site clear of rocks, branches, and other hard or sharp
objects, to install your tent.
WARNING: Keep clear of overhead power lines.
Do not set up your tent under trees because of potential lightning strikes or
falling tree limbs in inclement weather.
Secure with all stakes and guylines provided to prevent property damage
or personal injury.
•
•
6. Rotate all eight Leg Poles upright and insert pin on each
web loop at the side locations as shown. (Fig. 7 & 7A)
•
•
For best results in windy conditions, position narrow end of tent into the wind.
Enlist the help of at least one other person to assist you when it is time to
assemble the tent.
7A
Pin
Pole Descriptions
Pole
Pole
Description
Qty. Repair Kit
Replacement Kit
Long Leg Pole, steel
(w/ red marking)
4
4
N/A
N/A
5010000754
5010000755
Short Leg Pole, steel
Curved Ridge Pole, steel
(w/ red marking)
Curved Ridge Pole, steel
Awning Pole, black,
fiberglass, metal tips
Door Pole, long, thin, black,
fiberglass, rubber tips
Vert. Door Pole, short, black,
fiberglass, rubber tips
2
2
N/A
N/A
5010000756
5010000757
2
1
1
5010000543
5010000543
5010000543
5010000545
5010000545
5010000545
Fig. 7
7. Locate the plastic hooks at sides and
corners of tent, then snap onto Leg Poles to
attach. (Fig. 8)
Self-Rolling Window Spring Descriptions
Color Code Description
Qty.
1
Replacement Part No.
5010000624
Fig. 8
Fig. 9
Red
Yellow
Green
Orange
2
1
2
5010000626
5010000627
5010000628
8. To stretch tent to finished size:
•
Push in button on Leg Pole while
twisting lower Leg Pole section
counterclockwise (Fig.9);
Upper
Leg Pole
Section
CAUTION: “Springs” may have sharp edges. Handle with care to avoid injury.
•
•
Pull up on top Leg Pole section until
tent is taut;
Twist the lower Leg Pole clockwise
until the button locks into the center or
lowest hole;
Keep out of reach of children.
Button
Center Hole
Lower Hole
To Set Up Tent
1. Unfold tent and spread out on a clean, level surface with the door facing
Lower
the desired direction. Unzip doors. (Fig. 1)
Leg Pole
Fig. 1
Section
•
Repeat on remaining Leg Poles.
9. Insert plastic stakes through web straps located on
both sides of tent, then drive in to secure. (Fig. 10)
NOTE: It may be necessary to remove metal stakes
through web straps at side of tent and screen room,
pull tent taut, and drive in stakes to secure.
Door
2. Pull four corners of tent taut, then secure by driving
stakes through web loops at an angle for better
anchoring. (Fig. 2)
Fig. 10
Hinged, Rigid Door
1. Assemble Vertical Door Pole (shorter black pole with plastic tips); then insert
through zippered vertical pole sleeve on hinged side of door. (Fig. 11)
2. Insert end of Vertical Door Pole into bottom hinge plate, apply pressure to
form a slight bow, then insert other tip of pole into top hinge. Zip up verti-
cal pole sleeve. (Fig. 12 & 13)
3. Assemble Door Pole (longer black pole with plastic cap tips); then insert
into zippered pole sleeve at top of door. (Fig. 14)
4. Insert end of Door Pole into top hinge plate, apply pressure to form a bow,
then insert other tip of pole into the bottom hinge. (Fig. 15)
5. Zip up pole sleeve to enclose Door Pole. (Fig. 16)
Fig. 2
3. Assemble four, steel, shock-corded, curved
Ridge Poles. Insert Ridge Poles (with red
marking) into center sleeves on top of tent with
the red trim (Fig. 3). Insert the remaining curved
Ridge Poles into the other two sleeves on top of
tent.
Fig. 3
Ridge Pole
with Red
Marking
Sleeve
with Red
Trim
4. Assemble eight, steel, shock-corded, Leg Poles.
Push down on steel button on tapered end and
insert into end with four holes.
Fig. 11
Fig. 12
Fig. 13
Vertical Pole
Sleeve
Button in third hole
NOTE: Make sure steel button locks into third
hole on pole as shown. (Fig.4)
Fig. 4
Door Hinge
5. Insert curved end of Leg Poles
(with red marking) into the
Ridge Pole with
Red Marking
ends of the Ridge Pole (with
Fig. 15
Fig. 14
red marking). Insert curved
end of remaining short Leg
Poles into the ends of the
remaining Ridge Poles.
(Fig. 5 & 6)
Top
Door
Sleeve
with Red
Trim
Pole
Sleeve
Curved End of
Long Leg Pole
Hinge
Fig. 16
Fig. 5
Download from Www.Somanuals.com. All Manuals Search And Download.
(continued on other side)
|