Cisco MeetingPlace Audio Server Release 5.2
DVD-ROM Upgrade Procedure
Cisco MeetingPlace Audio Server Release 5.2 supports a new DVD-ROM drive that replaces the Travan
NS20 tape drive.
Note
You must upgrade the Cisco MeetingPlace 8112 before upgrading Cisco MeetingPlace Audio Server
Release 5.0.2 or Release 5.1.0 to Release 5.2.
Cisco MeetingPlace Audio Server Release 5.2 DVD-ROM Upgrade Procedure provides instructions for
removing the Travan NS20 tape drive and installing the DVD-ROM drive. For regulatory and compliance
information for Cisco MeetingPlace Audio Servers, see Regulatory Compliance and Safety Information
Contents
•
•
•
•
•
•
•
•
•
•
•
Audience
This upgrade procedure is for Network Consulting Engineers (NCE) or fully trained Cisco partners.
Cisco MeetingPlace Audio Server Release 5.2 DVD-ROM Upgrade Procedure
78-16489-01
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Required Tools and Equipment
Required Tools and Equipment
To upgrade to the Cisco MeetingPlace Audio Server Release 5.2 DVD-ROM, you need the following
tools and equipment:
•
•
•
•
•
•
•
Computer with terminal emulation software installed
DB9-female-to-DB9-female null-modem cable
Phillips #2 screwdriver
ESD protection
Small flashlight
Blank diskette
Releasable cable tie
How to Upgrade to the Cisco MeetingPlace Audio Server
Release 5.2 DVD-ROM
To upgrade to the Cisco MeetingPlace Audio Server Release 5.2 DVD-ROM, perform the following
procedures in the order shown:
•
•
•
•
•
•
•
•
Saving the License Keys
To save the license keys, perform the following steps:
Step 1
Step 2
By using the null-modem cable, connect the laptop to the COM1 service port on the front of the
Cisco MeetingPlace 8112.
Through a Telnet session or HyperTerminal, log in as a technician.
The tech$ prompt appears.
Step 3
Insert a blank disk into the floppy disk drive.
Cisco MeetingPlace Audio Server Release 5.2 DVD-ROM Upgrade Procedure
78-16489-01
3
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Upgrade to the Cisco MeetingPlace Audio Server Release 5.2 DVD-ROM
Step 4
Step 5
To save the license keys, enter savelicense.
You can use these license keys if you need to reinstall the original CPU.
Remove the disk from the floppy disk drive.
Powering Down the Cisco MeetingPlace 8112
To power down the Cisco MeetingPlace 8112, perform the following steps:
Step 1
Step 2
Step 3
Step 4
Step 5
At the tech$ prompt, enter halt disable.
To power down the system, enter y and press Enter.
Wait for the “**** LynxOS is down ****”message to appear.
Turn the power switch to the off position.
Unplug the main power cable from the server.
Removing the Tape Drive from the Cisco MeetingPlace 8112
To remove the tape drive from the Cisco MeetingPlace 8112, perform the following steps:
Step 1
Step 2
From the back of the Cisco MeetingPlace 8112, loosen the screws on the floppy disk housing, located
on the upper left side.
Slowly slide out the floppy disk housing and secure the housing to the back of the
Figure 1
Secured Floppy Disk Housing
Caution
Do not allow the housing to hang by the attached cables.
Cisco MeetingPlace Audio Server Release 5.2 DVD-ROM Upgrade Procedure
78-16489-01
4
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Upgrade to the Cisco MeetingPlace Audio Server Release 5.2 DVD-ROM
Step 3
Disconnect the power cable, a small connector with four connected wires, from the floppy disk drive in
Figure 2
Floppy Disk Drive Inside the Housing
Power Cable
SCSI Cable
Step 4
Step 5
Follow the internal pale yellow SCSI cable, as shown in Figure 2, from the floppy disk drive to identify
its connection to the tape drive, located at the top right and partially covered by the backplane.
Disconnect the SCSI cable from the tape drive.
Caution
Step 6
Do not to pull off the cable from the hard drives.
Figure 3
PWR1 Receptacle
Step 7
Disconnect the connector at PWR1.
Cisco MeetingPlace Audio Server Release 5.2 DVD-ROM Upgrade Procedure
78-16489-01
5
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Upgrade to the Cisco MeetingPlace Audio Server Release 5.2 DVD-ROM
Step 8
Note
Remove the power cable from the top disk drive on the top left from back of server, as shown in Figure 4.
There are two cables connected: the pale yellow SCSI cable and the power cable. Do not remove the
SCSI cable from the disk drive.
You may need to move other cables out of the way to see the connector. Make sure that the power cable
is not tangled with other cables. The power cable will need to extend when you slide out with the tape
drive.
Figure 4
Power Cable Connector on Top Disk Drive
Power Cable Connector
Step 9
Note
At the front of the Cisco MeetingPlace 8112, remove the faceplate to the drive bay by loosening the four
screws at the corners of the drive bay.
Do not turn the drive keys.
Cisco MeetingPlace Audio Server Release 5.2 DVD-ROM Upgrade Procedure
78-16489-01
6
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Upgrade to the Cisco MeetingPlace Audio Server Release 5.2 DVD-ROM
Figure 5
Captive Screws on the Drive Bay
Step 11 Slowly slide out the tape drive. You should be able to slide out the tape drive such that it narrowly clears
the bay.
Tip
If you cannot slide out the tape drive, go to the back of the server to see what is preventing the tape drive
from sliding out.
Step 12 Disconnect the power cable from the tape drive.
Step 13 Remove the tape drive.
Installing the DVD-ROM Drive into the Cisco MeetingPlace 8112
Step 1
Connect one end of the IDE cable to the DVD-ROM drive. The IDE cable is keyed, as shown in Figure 6,
and can only be connected one way.
Figure 6
IDE Cable
Step 2
Step 3
Step 4
From the front of the server, hold the DVD-ROM drive with the ejector button on the top and place the
IDE cable, connector end first, into the drive bay.
Slide in the IDE cable into the drive bay as far as possible so that you can access the cable from the back
of the Cisco MeetingPlace 8112.
Connect the power cable, the previous tape drive power cable, to the DVD-ROM drive.
Cisco MeetingPlace Audio Server Release 5.2 DVD-ROM Upgrade Procedure
78-16489-01
7
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Upgrade to the Cisco MeetingPlace Audio Server Release 5.2 DVD-ROM
Step 5
Step 6
If you have to pull out the power cable to connect it to the DVD-ROM drive, make sure that you put the
power cable back into the drive bay. Slide the power cable back in as far as possible so that you can
access the cable from the back of the server.
Slide the DVD-ROM drive into the drive bay. You may not be able to fully insert the DVD-ROM drive
because the IDE cable may bunch up.
Step 7
Step 8
Go to the back of server and carefully straighten out the IDE cable.
Verify that the IDE cable clips are open and insert the IDE cable connector to the PIDEA receptacle,
When you push in the connector, the top and bottom clips of the receptacle secure the connector.
Figure 7
PIDEA Receptacle
PIDEA Receptacle
Step 9
Reconnect the power cable connector with the red wire on top to the disk drive, located at top left. This
connector is keyed and can only be inserted one way.
Step 10 Reconnect the power cable connector with the red wire on top to the PWR1 receptacle. Use a flashlight
to ensure proper connection. This connector is keyed and can only be inserted one way.
Caution
If you do not reconnect the power cable connector properly, the server will be damaged and will not boot
up.
Step 11 Go to the front of the server and insert fully the DVD-ROM drive into the drive bay and tighten the
captive screws.
Step 12 Replace the face plate of the drive bay and fasten the four screws.
Step 13 After completing the installation, verify all the connections.
Step 14 Remove the releasable tie wrap that is securing the floppy drive housing to the back of the server.
Step 15 Reconnect the power cable connector with the red wire on top to the floppy disk drive. This connector
is keyed and can only be inserted one way.
Step 16 Slide the floppy drive housing back into the server and fasten the four screws. Take care not to pinch any
cables.
Cisco MeetingPlace Audio Server Release 5.2 DVD-ROM Upgrade Procedure
78-16489-01
8
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Upgrade to the Cisco MeetingPlace Audio Server Release 5.2 DVD-ROM
Upgrading the Cisco MeetingPlace 8112 BIOS
Caution
During this process, ensure that the power to the Cisco MeetingPlace 8112 is not turned off at any time.
To upgrade the Cisco MeetingPlace 8112 server BIOS, perform the following steps:
Step 1
Step 2
Step 3
Step 4
Step 5
Step 6
Step 7
Attach the monitor (LILLIPUT) to the Video port on the CPU card of the Cisco MeetingPlace 8112.
Attach the power cable to the monitor (LILLIPUT) and power source.
Attach the keyboard to the Keyboard/Mouse port on the CPU card of the Cisco MeetingPlace 8112.
Turn on the monitor (LILLIPUT).
Plug in the main power cable to the Cisco MeetingPlace 8112 and switch the server power to ON.
To get the log in prompt, press enter a couple of times; then, log in as a technician.
At the tech$ prompt, enter restart disable.
The server will start to come up immediately, and you will see “Press F2 to Enter Set Up” on the bottom
left side of the monitor (LILLIPUT).
Step 8
To enter setup mode, press F2.
Figure 8
BIOS Setup Utility Main Screen
Cisco MeetingPlace Audio Server Release 5.2 DVD-ROM Upgrade Procedure
78-16489-01
9
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Upgrade to the Cisco MeetingPlace Audio Server Release 5.2 DVD-ROM
Step 9
Figure 9 Advanced Screen
Step 11 In the Task Section of the Embedded Flash screen, press Enter.
Figure 10
Embedded Flash Screen
If Device is not set to Disk Drive, use the down arrow key to choose Device and use the + key ('shift' '+'
key) combination to choose Diskette Drive.
Step 14 Insert the BIOS 5.2 upgrade diskette into the floppy disk drive.
It may take up several minutes for the upgrade to begin. The Cisco MeetingPlace 8112 restarts.
Cisco MeetingPlace Audio Server Release 5.2 DVD-ROM Upgrade Procedure
78-16489-01
10
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Upgrade to the Cisco MeetingPlace Audio Server Release 5.2 DVD-ROM
Step 16 During the server reboot, watch for the BIOS revision SMM5370LATUDE BIOS 1.0EA02 on the
verifies that the BIOS was upgraded.
Figure 11
BIOS Revision
Step 17 Remove the BIOS disk from the floppy disk drive.
Step 18 Disconnect the monitor (LILLIPUT) and the keyboard from the Cisco MeetingPlace 8112 and
disconnect the power cable to
Cisco MeetingPlace Audio Server Release 5.2 DVD-ROM Upgrade Procedure
78-16489-01
11
How to Upgrade to the Cisco MeetingPlace Audio Server Release 5.2 DVD-ROM
If the server does not boot up (you cannot get into the Setup mode on the monitor), contact Cisco TAC
Step 5
Step 6
Step 7
In Setup mode, press the right arrow to choose the Advanced menu.
By using the Down arrow, choose IDE Configuration and press Enter.
Note
Do not save when you are prompted.
Figure 12
IDE Configuration Screen
Should be set
to“Both”
Step 8
If the Cisco MeetingPlace 8112 comes up after exiting the BIOS, proceed to the “Installing the
or
If the server does not come up after exiting the BIOS, contact Cisco TAC as described in the “Obtaining
Replacing the CPU and Updating the License Keys
To replace the CPU and update the license keys, perform the following steps:
Step 1
Step 2
Obtain new license keys by contacting Cisco TAC.
Verify that the power is off on the Cisco MeetingPlace 8112 and your laptop is connected to the service
port on the front of the server with the null-modem cable.
Step 3
Step 4
Step 5
Step 6
Step 7
Step 8
Remove the old CPU card and replace it with the new CPU card.
Place the old CPU card in the anti-static bag from which you removed the new CPU card.
Power up the server.
Log in as a technician.
Check for alarms.
Verify that there is a modem line connected to the server.
Cisco MeetingPlace Audio Server Release 5.2 DVD-ROM Upgrade Procedure
78-16489-01
12
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Upgrade to the Cisco MeetingPlace Audio Server Release 5.2 DVD-ROM
Step 9
Inform Cisco TAC that you are ready for the license key replacement.
Step 10 Perform full functionality testing.
Step 11 Return the old CPU card to manufacturing.
Installing the DVD-ROM Drive Software
Step 1
By using the null modem cable, connect the laptop to the COM1 service port on the front of the
Cisco MeetingPlace 8112.
Step 2
Log in to the server as a technician through a telnet session or HyperTerminal.
Tip
We recommend that you log your session.
Step 3
Step 4
Insert the Update Diskette for M3 DVD-ROM into the floppy disk drive.
To install the DVD-ROM software on the system hard drive, enter update at the tech$ prompt and choose
d for diskette.
Step 5
Step 6
When the system reminds you to wait for the blinking light to stop, press Enter.
After the light stops blinking, remove the diskette from the floppy disk drive.
The server is now upgraded to use the DVD-ROM drive.
Step 7
Step 8
Step 9
Insert the CD-ROM that contains the test image into the DVD-ROM drive.
At the tech$ prompt, enter update.
When prompted, choose 1 for CD and press Enter.
Step 10 When prompted to continue or abort, press Enter.
After the update is completed, a CD mounted OK message and more system options appear.
Step 11 To perform the CD Test, choose 1 when you are asked to choose the desired set.
Step 12 When you are prompted to install the CD Test, enter y. Sample output from a CD test is shown in the
Step 13 If the test passes, proceed to “Verifying the Cisco MeetingPlace Audio Server Release 5.2 DVD-ROM
or
If the test fails, contact Cisco TAC.
Installing the DVD-ROM Software Example
The following is sample output from a CD-ROM test that passes.
server: tech$ update
Update is from
1) CD
2) Diskette
3) Remote File
Cisco MeetingPlace Audio Server Release 5.2 DVD-ROM Upgrade Procedure
78-16489-01
13
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Upgrade to the Cisco MeetingPlace Audio Server Release 5.2 DVD-ROM
4) Local File
q) (Quit Update)
Enter choice: 1
Please insert the update CD in the drive, then
wait for the drive to be quiet before continuing.
Press <ENTER> to continue or <CONTROL-C> to abort.
CD mounted OK; checking for update sets...
There is more than one update set on the CD.
Please pick the desired set from the following list:
1) CD Test
2) MP Server 5.2.x
q) Quit
Enter Choice: 1
You wish to install: CD Test
Is this correct? (y or n) y
This test verifies proper operation of the CD drive.
The test image checksum matches.
Starting scan of the CD image. You should see no error messages.
When complete, a report should show the file system size and transfer speed.
dd: read 1341440 bytes; wrote 1341440 bytes; speed = 601.0 KB/s.
PASSED
Verifying the Cisco MeetingPlace Audio Server Release 5.2 DVD-ROM Upgrade
After the upgrade is successful, perform the following applicable system-wide checks to verify that the
Cisco MeetingPlace system is fully functional:
•
•
•
•
Verifying VoIP and PSTN Telephony with a Cisco MeetingPlace System
•
•
•
Verify that users can dial in or out of the Cisco MeetingPlace system using PSTN or VoIP.
Confirm that the server is playing meeting prompts in the correct languages.
Dial the DID number of the server.
The Cisco MeetingPlace system answers the call, and you hear the “Welcome to MeetingPlace”
prompt.
•
Schedule an immediate meeting on each server. Join the meeting and press #31 to dial another phone
number.
Scheduling and Attending New Meetings with a Cisco MeetingPlace System
•
•
•
Schedule and attend an immediate meeting via the phone interface.
Schedule and attend a future meeting via the phone interface.
Via the appropriate Cisco MeetingTime workstation client, log in through a System Manager profile
and schedule and attend an immediate meeting.
Cisco MeetingPlace Audio Server Release 5.2 DVD-ROM Upgrade Procedure
78-16489-01
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional References
Recording Conferences with a Cisco MeetingPlace System
•
Schedule a meeting with recording turned on. Verify that the meeting was recorded and that the
recording was retrievable after the meeting.
•
Schedule a meeting with recording turned off. During the meeting, turn on recording. Verify that the
meeting is recorded and that the recording is retrievable after the meeting.
Verifying Cisco MeetingPlace Gateway Functionality
•
Verify Cisco MeetingPlace notification gateway functionality by performing the following steps:
1. Schedule a meeting with both sending and receiving notification enabled.
2. Verify that the meeting notification is sent via e-mail.
•
Verify Cisco MeetingPlace for Outlook scheduling functionality by performing the following steps:
1. Schedule a meeting by using the Cisco MeetingPlace for Outlook scheduling form.
2. Verify that a confirmation message is sent back to the meeting scheduler indicating that the
meeting scheduling operations succeeded.
•
Verify Cisco MeetingPlace Web Conferencing functionality by performing the following steps:
1. Schedule a meeting through Cisco MeetingPlace Web Conferencing.
2. Attend a web conference.
3. Share and collaborate a document.
4. Test the slide show.
5. Test annotations.
Additional References
•
•
•
•
•
Regulatory Compliance and Safety Information for Cisco MeetingPlace 8100 Series
Addendum to Latitude MeetingPlace Documentation
Customer Engineering Guide for Cisco MeetingPlace Audio Server 5.2
Cisco MeetingPlace Audio Server 5.2 System Manager's Guide for Cisco MeetingPlace 8100 series
Cisco MeetingPlace Audio Server 5.2 Installation Planning Guide for Cisco MeetingPlace 8100
series
Cisco MeetingPlace Audio Server Release 5.2 DVD-ROM Upgrade Procedure
78-16489-01
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Obtaining Documentation
Obtaining Documentation
Cisco documentation and additional literature are available on Cisco.com. Cisco also provides several
ways to obtain technical assistance and other technical resources. These sections explain how to obtain
technical information from Cisco Systems.
Cisco.com
You can access the most current Cisco documentation at this URL:
You can access the Cisco website at this URL:
You can access international Cisco websites at this URL:
Documentation DVD
Cisco documentation and additional literature are available in a Documentation DVD package, which
may have shipped with your product. The Documentation DVD is updated regularly and may be more
current than printed documentation. The Documentation DVD package is available as a single unit.
Registered Cisco.com users (Cisco direct customers) can order a Cisco Documentation DVD (product
number DOC-DOCDVD=) from the Ordering tool or Cisco Marketplace.
Cisco Ordering tool:
Cisco Marketplace:
Ordering Documentation
You can find instructions for ordering documentation at this URL:
You can order Cisco documentation in these ways:
•
Registered Cisco.com users (Cisco direct customers) can order Cisco product documentation from
the Ordering tool:
•
Nonregistered Cisco.com users can order documentation through a local account representative by
calling Cisco Systems Corporate Headquarters (California, USA) at 408 526-7208 or, elsewhere in
North America, by calling 1 800 553-NETS (6387).
Cisco MeetingPlace Audio Server Release 5.2 DVD-ROM Upgrade Procedure
78-16489-01
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Documentation Feedback
Documentation Feedback
You can submit comments by using the response card (if present) behind the front cover of your
document or by writing to the following address:
Cisco Systems
Attn: Customer Document Ordering
170 West Tasman Drive
San Jose, CA 95134-9883
We appreciate your comments.
Cisco Product Security Overview
Cisco provides a free online Security Vulnerability Policy portal at this URL:
From this site, you can perform these tasks:
•
•
•
Report security vulnerabilities in Cisco products.
Obtain assistance with security incidents that involve Cisco products.
Register to receive security information from Cisco.
A current list of security advisories and notices for Cisco products is available at this URL:
If you prefer to see advisories and notices as they are updated in real time, you can access a Product
Security Incident Response Team Really Simple Syndication (PSIRT RSS) feed from this URL:
Reporting Security Problems in Cisco Products
Cisco is committed to delivering secure products. We test our products internally before we release them,
and we strive to correct all vulnerabilities quickly. If you think that you might have identified a
vulnerability in a Cisco product, contact PSIRT:
•
•
Tip
We encourage you to use Pretty Good Privacy (PGP) or a compatible product to encrypt any sensitive
information that you send to Cisco. PSIRT can work from encrypted information that is compatible with
PGP versions 2.x through 8.x.
Never use a revoked or an expired encryption key. The correct public key to use in your correspondence
with PSIRT is the one that has the most recent creation date in this public key server list:
Cisco MeetingPlace Audio Server Release 5.2 DVD-ROM Upgrade Procedure
78-16489-01
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Obtaining Technical Assistance
In an emergency, you can also reach PSIRT by telephone:
•
•
1 877 228-7302
1 408 525-6532
Obtaining Technical Assistance
For all customers, partners, resellers, and distributors who hold valid Cisco service contracts, Cisco
Technical Support provides 24-hour-a-day, award-winning technical assistance. The Cisco Technical
Support Website on Cisco.com features extensive online support resources. In addition, Cisco Technical
Assistance Center (TAC) engineers provide telephone support. If you do not hold a valid Cisco service
contract, contact your reseller.
Cisco Technical Support Website
The Cisco Technical Support Website provides online documents and tools for troubleshooting and
resolving technical issues with Cisco products and technologies. The website is available 24 hours a day,
365 days a year, at this URL:
Access to all tools on the Cisco Technical Support Website requires a Cisco.com user ID and password.
If you have a valid service contract but do not have a user ID or password, you can register at this URL:
Note
Use the Cisco Product Identification (CPI) tool to locate your product serial number before submitting
a web or phone request for service. You can access the CPI tool from the Cisco Technical Support
Website by clicking the Tools & Resources link under Documentation & Tools. Choose Cisco Product
Identification Tool from the Alphabetical Index drop-down list, or click the Cisco Product
Identification Tool link under Alerts & RMAs. The CPI tool offers three search options: by product ID
or model name; by tree view; or for certain products, by copying and pasting show command output.
Search results show an illustration of your product with the serial number label location highlighted.
Locate the serial number label on your product and record the information before placing a service call.
Submitting a Service Request
Using the online TAC Service Request Tool is the fastest way to open S3 and S4 service requests. (S3
and S4 service requests are those in which your network is minimally impaired or for which you require
product information.) After you describe your situation, the TAC Service Request Tool provides
recommended solutions. If your issue is not resolved using the recommended resources, your service
request is assigned to a Cisco TAC engineer. The TAC Service Request Tool is located at this URL:
For S1 or S2 service requests or if you do not have Internet access, contact the Cisco TAC by telephone.
(S1 or S2 service requests are those in which your production network is down or severely degraded.)
Cisco TAC engineers are assigned immediately to S1 and S2 service requests to help keep your business
operations running smoothly.
Cisco MeetingPlace Audio Server Release 5.2 DVD-ROM Upgrade Procedure
78-16489-01
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Obtaining Additional Publications and Information
To open a service request by telephone, use one of the following numbers:
Asia-Pacific: +61 2 8446 7411 (Australia: 1 800 805 227)
EMEA: +32 2 704 55 55
USA: 1 800 553-2447
For a complete list of Cisco TAC contacts, go to this URL:
Definitions of Service Request Severity
To ensure that all service requests are reported in a standard format, Cisco has established severity
definitions.
Severity 1 (S1)—Your network is “down,” or there is a critical impact to your business operations. You
and Cisco will commit all necessary resources around the clock to resolve the situation.
Severity 2 (S2)—Operation of an existing network is severely degraded, or significant aspects of your
business operation are negatively affected by inadequate performance of Cisco products. You and Cisco
will commit full-time resources during normal business hours to resolve the situation.
Severity 3 (S3)—Operational performance of your network is impaired, but most business operations
remain functional. You and Cisco will commit resources during normal business hours to restore service
to satisfactory levels.
Severity 4 (S4)—You require information or assistance with Cisco product capabilities, installation, or
configuration. There is little or no effect on your business operations.
Obtaining Additional Publications and Information
Information about Cisco products, technologies, and network solutions is available from various online
and printed sources.
•
Cisco Marketplace provides a variety of Cisco books, reference guides, and logo merchandise. Visit
Cisco Marketplace, the company store, at this URL:
•
Cisco Press publishes a wide range of general networking, training and certification titles. Both new
and experienced users will benefit from these publications. For current Cisco Press titles and other
information, go to Cisco Press at this URL:
•
Packet magazine is the Cisco Systems technical user magazine for maximizing Internet and
networking investments. Each quarter, Packet delivers coverage of the latest industry trends,
technology breakthroughs, and Cisco products and solutions, as well as network deployment and
troubleshooting tips, configuration examples, customer case studies, certification and training
information, and links to scores of in-depth online resources. You can access Packet magazine at
this URL:
Cisco MeetingPlace Audio Server Release 5.2 DVD-ROM Upgrade Procedure
78-16489-01
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Obtaining Additional Publications and Information
•
iQ Magazine is the quarterly publication from Cisco Systems designed to help growing companies
learn how they can use technology to increase revenue, streamline their business, and expand
services. The publication identifies the challenges facing these companies and the technologies to
help solve them, using real-world case studies and business strategies to help readers make sound
technology investment decisions. You can access iQ Magazine at this URL:
•
•
Internet Protocol Journal is a quarterly journal published by Cisco Systems for engineering
professionals involved in designing, developing, and operating public and private internets and
intranets. You can access the Internet Protocol Journal at this URL:
World-class networking training is available from Cisco. You can view current offerings at
this URL:
Cisco MeetingPlace Audio Server Release 5.2 DVD-ROM Upgrade Procedure
78-16489-01
20
Download from Www.Somanuals.com. All Manuals Search And Download.
|