Basic V110 for MICA Modems on
Cisco Access Servers
Feature Overview
This feature allows V.110 calls to be originated and terminated over ISDN. The V.110
recommendation of the ITU-T rate adapts a low speed connection to an ISDN-B channel allowing
the remote station or terminal adaptor to use the fast call set-up times offered by ISDN. This feature
enables GSM wireless connectivity.
This document describes the Cisco IOS commands and AT commands required to support V.110 on
MICA modems for AS5X00 Access Servers.
This MICA V.110 implementation supports 60 modems per board on the Cisco AS5300 and supports
other connect standards (V.34, V.90, etc.) in addition to V.110. Modems are not dedicated to V.110
only and are allocated dynamically. On the Cisco AS5200, 30 modems per board is supported and
72 modems per board is supported on the Cisco AS5800.
This V.110 implementation for calls on MICA modems are managed by special boardware and
modem code, along with the appropriate Cisco IOS image, in a manner similar to other modulation
standards.
Note This document is in development. Portions of this document may not be complete or
developed according to the current documentation standards. This document is subject to revision
when the content is available and developed further. Please check the online version periodically
until the document is completed according to the usual documentation standards.
Feature Summary
• Bearer Rate supported range from 600 bps to 38400 bps.
• Modem Management is supported.
• Modem Log for V.110 calls is supported.
• show modem (Number of connections at specific line speeds is supported.)
• show modem (Number of calls counters supported)
• show modem (Display of Tx/Rx line speeds is supported.)
• show modem version is supported.
• show modem configuration is supported.
• show modem operational-status is supported.
• ATDI command is added to AT command set for V.110 modem dialouts.
Basic V110 for MICA Modems on Cisco Access Servers 1
Download from Www.Somanuals.com. All Manuals Search And Download.
Related Features and Technologies
— 64k bps
Related Features and Technologies
This feature requires special modem code to be downloaded to the MICA Modems. See the online
CCO modem information page.
Related Documents
See the modem code online documentation for the platform you are using:
• Firmware and Portware Information
See also the following documents:
• 12.0 Dial Solutions Command Reference (DR)
• Cisco AS5800—Modem and System Management Features for the Cisco AS5800
• Online product-specific release notes for the corresponding platforms on the appropriate Cisco
IOS release. Start from the appropriate Cisco IOS numbered release on this page:
Cisco IOS Software Configuration:
Supported Platforms
• Cisco AS5200 in Cisco IOS Release 12.(4)XI1
• Cisco AS5300 in Cisco IOS Release 12.(4)XI1
• Cisco AS5800 (not currently supported)
Prerequisites
Supporting boardware and modem code on the MICA modems and special versions of the CSM on
Supported MIBs and RFCs
The current Modem Management MIB objects for MICA modems will also be used for V.110. One
minor change is in the SNMP agent code. This change returns the correct modulation type for V.110
when it does a look up of the modulation for MICA modems.
Basic V110 for MICA Modems on Cisco Access Servers 3
Download from Www.Somanuals.com. All Manuals Search And Download.
List of Terms and Acronyms
Boardware—
CSM—
E1—
Software that runs on the CPU on the certain supporting cards
Call Switching Module
European equivalent of T1, 32 channels of 64KHz, 1 for framing, 1 for signaling
Global System for Communications
Hex Modem Module
GSM—
HMM—
IOS—
Internetworking Operating System
ISDN—
Integrated Services Digital Network
LLC—
Link Layer Control
MICA—
MSM—
Portware—
PRI—
Modem ISDN Channel Aggregation
Modem State Machine
Software that runs on MICA digital modem module
Primary Rate Interface
Q.931—
T1—
ISDN User-Network Interface Layer 3 Specification for Basic Call Control
North American Channelized TDM w/ 24 channels of 64Khz each plus 8Khz frame
TA—
Terminal Adapter
V.110—
ITU-T Standard for support by ISDN of Data Terminal Equipment with V-Series Type
Interfaces
Configuration Tasks
There are no configuration tasks. All commands in this feature are modified existing show modem
commands.
Command Reference
This section documents modified commands. All other commands used with this feature are
documented in the Cisco IOS Release 12.0 command references and the Cisco AS5800 online new
feature documentation. For more information, see the documentation for the existing show modem
commands.
No new IOS commands are being added to support V.110 on MICA. However, due to the new V.110
Connect Protocol, Connected Standard, Line Speeds (Bearer Rates) and counters, the code that
handles the following show modem commands has been modified as listed in the following logical
order:
• show modem
Cisco IOS Release 12.0(4)XI1
4
Download from Www.Somanuals.com. All Manuals Search And Download.
show Command Examples
modmgt.htm#xtocid10451223
See also show modem at:
ats/c5800uas.htm#19600
• show modem log
modmgt.htm#xtocid10451261
• show modem configuration
modmgt.htm#xtocid10451239
• show modem connect-speeds
modmgt.htm#xtocid10451245
• show modem operational-status
modmgt.htm#xtocid10451279
For the commands above, MICA Modem Management code has been modified to display the correct
information for V.110 associated Connect Protocol and Connected Standard. In addition, the correct
line speeds for V.110 related Bearer Rates have also be added to commands that display the
information.
For other and related modem management commands, such as modem-at mode, see:
dmgt.htm#xtocid104510
show Command Examples
The show modem command includes outputs for the show modem configuration command and
the show modem connect-speeds command.
show modem
Fields that have been added or changed for this command are:
Modem Type V.110
Protocol: ISDN Mode
Connection Speeds 34000
The show modem command example is as follows:
router# show modem 1/0
Mdm Typ
1/0 V.110
Status
Conn
Tx/Rx
9600/9600
G Duration
0 10:12:19
RTS CTS DCD DTR
x
x
x
x
Modem 1/0, Mica Hex Modem (Managed), Async1, TTY1
Firmware Rev: 2.7.0.6
Modem config: Incoming and Outgoing
Protocol: ISDN Mode, Compression: None
Management config: Status polling
RX signals: 0 dBm
Basic V110 for MICA Modems on Cisco Access Servers 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Last clearing of "show modem" counters never
23 incoming completes, 2 incoming failures
0 outgoing completes, 0 outgoing failures
0 failed dial attempts, 0 ring no answers, 2 busied outs
0 no dial tones, 0 dial timeouts, 0 watchdog timeouts
0 no carriers, 0 link failures, 0 resets, 0 recover oob
0 recover modem, 0 current fail count
0 protocol timeouts, 0 protocol errors, 0 lost events
0 ready poll timeouts
Transmit Speed Counters:
Connection Speeds
# of connections
Connection Speeds
# of connections
Connection Speeds
# of connections
Connection Speeds
# of connections
Connection Speeds
# of connections
Connection Speeds
75
0
7200
1
21600
0
30667
0
300
0
9600
4
24000
0
31200
0
600
0
12000
0
26400
0
32000
0
1200
0
14400
3
28000
0
33333
0
2400
0
16800
0
28800
0
33600
0
4800
1
19200
8
29333
0
34000
0
34667
0
40000
36000
0
41333
37333
0
42000
38000
0
42667
38400
6
44000
38667
0
45333
Receive Speed Counters:
Connection Speeds
# of connections
Connection Speeds
# of connections
Connection Speeds
# of connections
Connection Speeds
# of connections
Connection Speeds
# of connections
Connection Speeds
# of connections
Connection Speeds
# of connections
Connection Speeds
# of connections
75
300
600
1200
2400
4800
0
7200
1
21600
0
30667
0
34667
0
40000
0
46000
0
52000
0
0
9600
4
24000
0
31200
0
36000
0
41333
0
46667
0
53333
0
0
12000
0
26400
0
32000
0
37333
0
42000
0
48000
0
54000
0
0
14400
3
28000
0
33333
0
38000
0
42667
0
49333
0
54667
0
0
16800
0
28800
0
33600
0
38400
6
44000
0
50000
0
56000
0
1
19200
8
29333
0
34000
0
38667
0
45333
0
50667
0
show modem operational-status
Fields that have been added or changed for this command are:
Parameter #1 Connect Protocol: ISDN Mode
Parameter #8 Connected standard V.110
Parameter #41 V110 frames received bad:
Parameter #42 V110 frames received good:
Parameter #43 V110 frames transmitted:
Parameter #44 V110 sync lost:
The show modem operational-status command example is as follows:
router# show modem operational-status 1/0
Modem(1/0) Operational-Status:
Parameter #0 Disconnect Reason Info: (0x0)
Type (=0 ): <unknown>
Class (=0 ): Other
Cisco IOS Release 12.0(4)XI1
6
Download from Www.Somanuals.com. All Manuals Search And Download.
show Command Examples
Reason (=0 ): no disconnect has yet occurred
Parameter #1 Connect Protocol: ISDN Mode
Parameter #2 Compression: None
Parameter #3 EC Retransmission Count: 0
Parameter #4 Self Test Error Count: 0
Parameter #5 Call Timer: 37079 secs
Parameter #6 Total Retrains: 0
Parameter #7 Sq Value: 7
Parameter #8 Connected Standard: V.110
Parameter #9 TX,RX Bit Rate: 9600, 9600
Parameter #11 TX,RX Symbol Rate: 0, 0
Parameter #13 TX,RX Carrier Frequency: 0, 0
Parameter #15 TX,RX Trellis Coding: (n/a), (n/a)
Parameter #16 TX,RX Preemphasis Index: 0, 0
Parameter #17 TX,RX Constellation Shaping: (n/a), (n/a)
Parameter #18 TX,RX Nonlinear Encoding: (n/a), (n/a)
Parameter #19 TX,RX Precoding: (n/a), (n/a)
Parameter #20 TX,RX Xmit Level Reduction: 0, 0 dBm
Parameter #21 Signal Noise Ratio: 0 dB
Parameter #22 Receive Level: 0 dBm
Parameter #23 Frequency Offset: 0 Hz
Parameter #24 Phase Jitter Frequency: 0 Hz
Parameter #25 Phase Jitter Level: 0 degrees
Parameter #26 Far End Echo Level: 0 dBm
Parameter #27 Phase Roll: 0 degrees
Parameter #28 Round Trip Delay: 0 msecs
Parameter #30 Characters transmitted, received: 247, 308
Parameter #32 Characters received BAD: 0
Parameter #33 PPP/SLIP packets transmitted, received: 9, 9
Parameter #35 PPP/SLIP packets received (BAD/ABORTED): 0
Parameter #36 EC packets transmitted, received OK: 0, 0
Parameter #38 EC packets (Received BAD/ABORTED): 0
Parameter #39 Robbed Bit Signalling (RBS) pattern: 0
Parameter #40 Digital Pad: (n/a), Digital Pad Compensation: None
Parameter #41 V110 frames received bad: 0
Parameter #42 V110 frames received good: 7417301
Parameter #43 V110 frames transmitted: 7417310
Parameter #44 V110 sync lost: 0
show modem log
Fields that have been added or changed for this command are:
Connect Protocol: ISDN Mode
Connected Standard V.110
V110 frames received bad:
V110 frames received good:
V110 frames transmitted:
V110 sync lost:
The show modem log command example is as follows:
router# show modem log 1/1
Modem 1/1 Events Log:
...
...
...
4d06h
4d06h
4d06h
:Modem State event:
State: Train Up
:Modem State event:
State: EC Negotiating
:Modem State event:
Basic V110 for MICA Modems on Cisco Access Servers 7
Download from Www.Somanuals.com. All Manuals Search And Download.
State: Steady
4d06h
4d06h
:RS232 event: RTS, DTR, CTS, DCD
:Static event:
Connect Protocol: ISDN Mode
Compression: None
Connected Standard: V.110
TX,RX Symbol Rate: 0, 0
TX,RX Carrier Frequency: 0, 0
TX,RX Trellis Coding: (n/a), (n/a)
Frequency Offset: 0 Hz
Round Trip Delay: 2 msecs
TX,RX Bit Rate: 19200, 19200
Robbed Bit Signalling (RBS) pattern: 0
Digital Pad: (n/a), Digital Pad Compensation: None
4d06h
:Dynamic event:
Sq Value: 7
Signal Noise Ratio: 0 dB
Receive Level: 0 dBm
Phase Jitter Frequency: 0 Hz
Phase Jitter Level: 0 degrees
Far End Echo Level: 0 dBm
Phase Roll: 0 degrees
Total Retrains: 0
EC Retransmission Count: 0
Characters transmitted, received: 0, 0
Characters received BAD: 0
PPP/SLIP packets transmitted, received: 0, 0
PPP/SLIP packets received (BAD/ABORTED): 0
EC packets transmitted, received OK: 0, 0
EC packets (Received BAD/ABORTED): 0
V110 frames received bad: 0
V110 frames received good: 51
V110 frames transmitted: 64
V110 sync lost: 0
...
...
...
1d11h
:Modem State event:
State: Terminate
1d11h
:RS232 event: RTS, DTR, CTS, noDCD
:Modem State event:
State: Idle
1d11h
1d11h
:End Connect event:
Call Timer: 87 secs
Disconnect Reason Info: (0xDF06)
Type (=6 ): Tx (host to line) data flushing - OK
Class (=31): Requested by host
Reason (=6 ): network indicated disconnect
Total Retrains: 0
EC Retransmission Count: 0
Characters transmitted, received: 308, 50042
Characters received BAD: 0
PPP/SLIP packets transmitted, received: 10, 43
PPP/SLIP packets received (BAD/ABORTED): 0
EC packets transmitted, received OK: 0, 0
EC packets (Received BAD/ABORTED): 0
V110 frames received bad: 3
V110 frames received good: 34493
V110 frames transmitted: 34710
V110 sync lost: 1
...
...
...
10:37:18:Static event:
Connect Protocol: ISDN Mode
Cisco IOS Release 12.0(4)XI1
8
Download from Www.Somanuals.com. All Manuals Search And Download.
ATDI Command (place V.110 call)
Compression: None
Connected Standard: V.110
TX,RX Symbol Rate: 0, 0
TX,RX Carrier Frequency: 0, 0
TX,RX Trellis Coding: (n/a), (n/a)
Frequency Offset: 0 Hz
Round Trip Delay: 2 msecs
TX,RX Bit Rate: 9600, 9600
Robbed Bit Signalling (RBS) pattern: 0
Digital Pad: (n/a), Digital Pad Compensation: None
10:37:20:Dynamic event:
Sq Value: 7
Signal Noise Ratio: 0 dB
Receive Level: 0 dBm
Phase Jitter Frequency: 0 Hz
Phase Jitter Level: 0 degrees
Far End Echo Level: 0 dBm
Phase Roll: 0 degrees
Total Retrains: 0
EC Retransmission Count: 0
Characters transmitted, received: 0, 0
Characters received BAD: 0
PPP/SLIP packets transmitted, received: 0, 0
PPP/SLIP packets received (BAD/ABORTED): 0
EC packets transmitted, received OK: 0, 0
EC packets (Received BAD/ABORTED): 0
V110 frames received bad: 0
V110 frames received good: 26
V110 frames transmitted: 33
V110 sync lost: 0
...
...
...
1d06h
:End Connect event:
Call Timer: 105 secs
Disconnect Reason Info: (0xDF06)
Type (=6 ): Tx (host to line) data flushing - OK
Class (=31): Requested by host
Reason (=6 ): network indicated disconnect
Total Retrains: 0
EC Retransmission Count: 0
Characters transmitted, received: 247, 307
Characters received BAD: 0
PPP/SLIP packets transmitted, received: 9, 9
PPP/SLIP packets received (BAD/ABORTED): 0
EC packets transmitted, received OK: 0, 0
EC packets (Received BAD/ABORTED): 0
V110 frames received bad: 3
V110 frames received good: 20758
V110 frames transmitted: 20995
V110 sync lost: 1
ATDI Command (place V.110 call)
The calling user can manually communicate with a V.110 modem in order to originate a remote
V.110 dialout from the called modem. The AT command set now includes the ATDI command
(place V.110 call) to allow a V.110 call to be originated from the called modem. The user enters the
ATDI command after establishing a session with the MICA modem in order to dial-out a V.110 call
from the modem.
Basic V110 for MICA Modems on Cisco Access Servers 9
Download from Www.Somanuals.com. All Manuals Search And Download.
By specifying a value 8 in S29, the user causes the remote modem to implicitly assume that a V.110
connection is to be established. This command indicates that an ISDN call is being requested, and
when used with the S29=8 command, results in modem code issuing a ISDN_DIALSTRING
(0x45) request being made to the host.
After entering the S29=8 command, you can enter the desired user rate if different from the default
value of 9600 bps. This command takes the form: S57=speed. For supported rates, see the
“Restrictions” section. For example:
S57=19200
Debug Commands
There are no debug commands specific to this feature. Existing ISDN debug commands can be used.
Example Debug Commands for Cisco AS5200 and Cisco AS5300
router# debug isdn q931
router# debug modem csm
router# term mon
Example Debug Commands for Cisco AS5800
router# debug isdn q931
router# debug csm
router# term mon
Cisco IOS Release 12.0(4)XI1
10
Download from Www.Somanuals.com. All Manuals Search And Download.
|