SLIDE RAIL INSTALLATION INSTRUCTIONS
For Cisco C170, M170, and S170
Appliances
and
Cisco 5512-X, 5515-X, 5525-X, 5545-X,
5555-X Adaptive Security Appliances
and
Cisco IPS 4345 and 4360
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Disassemble the Slide Rail
Pull the inner slide rail from the outer slide rail.
Front
Slide the plastic tab forward, and pull the inner slide rail to
disconnect it from the outer slide rail.
Repeat the steps on this page for the other slide rail.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Attach Inner Rails to the Chassis
Align one of the inner slide rail key holes over the chassis
shoulder screw on one side. Slide the inner slide rail forward so
that the shoulder screw is securely in place.
Use a Phillips screwdriver to secure the inner slide rail with one
B
Phillips flat-head screw
.
Secure the other inner slide rail to the chassis by repeating the
previous steps on this page.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Verify the Rack Type
The slide rails are pre-assembled for square hole racks. See the
following steps for the different rack types:
•
•
•
Threaded hole racks. Go to “Threaded Hole Racks” on
The following figure shows the slide rail with square hole rack
inserts.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
5 Round Hole Racks
Using a Phillips head screwdriver, remove the square insert from
the rear of the rail. Keep the two Phillips head screws.
Remove the square insert from the front of the rail. Keep the
two Phillips head screws.
C
Align the round hole insert
to the rear of the rail, and secure
it with two of the saved screws.
C
Align the round hole insert
to the front of the rail over the
hooks, and secure it with two of the saved screws.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
6 Threaded Hole Racks
Using a Phillips head screwdriver, remove the square hole insert
from the rear of the rail.
Remove the square hole insert from the front of the rail.
D
Align the threaded hole bracket
to the front of the rail over
E
the hooks. Secure it with the threaded hole standoff
flat-head screwdriver.
using a
No additional hardware is necessary for the rear adapter.
Repeat these steps page for the other slide rail. Go to the“Attach
7
Download from Www.Somanuals.com. All Manuals Search And Download.
7 Attach the Outer Slide Rail to
Round and Square Hole Racks
Align the front of one of the outer slide rails with the rack
upright, push it forward, and click it into place. Align the rear
of the outer slide rail with the rack upright, pull the release tab,
push the slide rail toward the rack, release the tab, and click it
into place.
Note
For racks shorter than 24 inches in depth, remove the
rear bracket with a Phillips head screwdriver, pull the
release tab, and adjust the slide rail to the appropriate
length for the rack.
Front of
Rack
Rear of
Rack
Rear of
Bracket
Secure the other outer slide rail to the rack by repeating the
previous steps.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
8 Attach the Outer Slide Rail to
Threaded Hole Racks
Align the slide rail to the front rack post. Secure it with two of
F
the included Phillips pan-head screws
.
Align the slide rail to the rear rack post. Secure it with two of
F
the included Phillips pan-head screws
.
Align the other slide rail to the rack by repeating the previous
steps on this page.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
9 Install the Chassis
Align the inner slide rails to the outer slide rails. Install the inner
slide rails into the outer slide rails until they lock into place.
Pull the side release tabs to unlock the inner slide rail, and push
the chassis assembly into the rack.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
10 Secure the Chassis
Secure the chassis to the rack with the front captive screws.
Obtaining Documentation and Submitting a
Service Request
For information on obtaining documentation, submitting a
service request, and gathering additional information, see the
monthly What’s New in Cisco Product Documentation, which
also lists all new and revised Cisco technical documentation, at:
ml
Subscribe to the What’s New in Cisco Product Documentation as
an RSS feed and set content to be delivered directly to your desktop
using a reader application. The RSS feeds are a free service. Cisco
currently supports RSS Version 2.0.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other
relationship between Cisco and any other company. (1110R)
© 2012 Cisco Systems, Inc. All rights reserved.
Americas Headquarters
Cisco Systems, Inc.
San Jose, CA
Asia Pacific Headquarters
Cisco Systems (USA) Pte. Ltd.
Singapore
Europe Headquarters
Cisco Systems International BV Amsterdam,
The Netherlands
Cisco has more than 200 offices worldwide. Addresses, phone numbers, and fax numbers are listed on
Printed in the USA on recycled paper containing 10% postconsumer waste.
78-19691-04
Download from Www.Somanuals.com. All Manuals Search And Download.
|