Chief Manufacturing Indoor Furnishings PNRIW User Manual

I N S T A L L A T I O N I N S T R U C T I O N S  
Instrucciones de instalación  
Installationsanleitung  
Istruzioni di installazione  
Installatie-instructies  
Instruções de Instalação  
Instructions d´installation  
Large Flat Panel In-Wall Swing Arm Mount  
Spanish Product Description  
German Product Description  
Portuguese Product Description  
Italian Product Description  
Dutch Product Description  
French Product Description  
PNRIW / PNRIWU  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation Instructions  
PNRIW / PNRIWU  
TOOLS REQUIRED FOR INSTALLATION AND PARTS  
(3/16")  
B (4)  
2 short (SIDES)  
2 long  
I/M  
A (1)  
x1  
E (4)  
5/16"  
D (4)  
5/16"  
C (4)  
5/16-18 x 5/8"  
F (16)  
G (4)  
J (1)  
H (1)  
3/16"  
M(4)  
L (4)  
K (1)  
Figure 1  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
PNRIW / PNRIWU  
Installation Instructions  
Installation  
The following procedure assumes that a Chief Model PAC501  
In-Wall accessory has previously been installed following the  
installation instructions provided with the PAC501. If a PAC501  
is not installed or there are any other questions regarding the  
installation of this accessory, immediately contact a Chief  
Customer Service representative by calling 800-582-6480 or by  
WARNING: IMPROPER INSTALLATION CAN LEAD TO  
MOUNT FALLING CAUSING SEVERE PERSONAL INJURY  
OR DAMAGE TO EQUIPMENT! DO NOT deviate from  
installation instructions provided. DO NOT substitute  
hardware.  
2
1. Align mounting holes in swing arm UPPER and LOWER  
mounting brackets with four mounting holes in PAC501.  
(See Figure 2)  
(E) x4  
(D) x4  
(C) x4  
Upper Mounting Bracket  
Figure 3  
1
Trim Installation  
To install optional trim;  
1. Remove paper covering adhesive and affix three tape  
squares (F) to inside lower flange of each trim piece (B).  
(See Figure 4)  
2. Orient trim pieces (B) as shown in figure below.  
(See Figure 4)  
3. Remove paper covering adhesive back from tape squares  
(F) on trim and press trim (B) against inner wall of box.  
(See Figure 4)  
1
Lower Mounting Bracket  
(B) x 4  
2
1
Figure 2  
2. Secure swing arm to PAC501 using four button head cap  
screws (C), four lock washers (D) and four flat washers (E).  
(See Figure 3)  
3
1
(F) x 12  
Figure 4  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation Instructions  
PNRIW / PNRIWU  
NOTE: Holes are provided in the faceplate for use with a  
padlock or similar locking device, if desired. In addition,  
the pin and nut may be removed from the upper holes  
and moved to the lower holes for use as a more  
permanent locking device. (See Figure 6)  
Display Installation  
WARNING: IMPROPER INSTALLATION CAN LEAD TO  
MOUNT FALLING CAUSING SEVERE PERSONAL INJURY  
OR DAMAGE TO EQUIPMENT! DO NOT install display in a  
manner other than that specified by the manufacturer. Certain  
displays may require the use of an interface bracket for  
proper installation of the display. If an interface bracket is not  
installed or there are any other questions regarding the  
installation of the display, immediately contact a Chief  
Customer Service representative by calling 800-582-6480 or  
Remove pin  
2
and nuts and  
move to lower holes.  
WARNING: IMPROPER INSTALLATION CAN LEAD TO  
MOUNT FALLING CAUSING SEVERE PERSONAL INJURY  
OR DAMAGE TO EQUIPMENT. Displays can weigh in  
excess of 40 lbs (18.1kg). ALWAYS use two people and  
proper lifting techniques when installing display.  
3
WARNING: IMPROPER INSTALLATION CAN LEAD TO  
MOUNT FALLING CAUSING SEVERE PERSONAL INJURY  
OR DAMAGE TO EQUIPMENT. Make sure mounting buttons  
on display are properly seated in mounting holes in faceplate.  
A padlock or bolt may  
be placed through latch  
holes  
To install display:  
1. Move mount faceplate to extended position by grasping  
faceplate and pulling outward away from wall.  
(See Figure 5)  
Figure 6  
Cable Management  
2. While supporting both sides of display, align four mounting  
buttons on display or interface bracket with four mounting  
holes in faceplate. (See Figure 5)  
CABLE MANAGEMENT  
3. Lower display into place listening for audible "click" to  
ensure recessed area of mounting buttons are properly  
seated in lower area of mounting holes and "click lock"  
mechanism has engaged. (See Figure 5) and  
(See Figure 6)  
WARNING: IMPROPER INSTALLATION CAN LEAD TO  
SERIOUS PERSONAL INJURY OR DAMAGE TO  
EQUIPMENT! Make sure cables do not run through pinch  
points.  
1. Loosen front and rear cable clamps on top arm.  
(See Figure 7)  
2. Thread cable ties (M) under cable clamps and secure  
clamps to top arm. (See Figure 7)  
3. Route power/audio/video cables through the cable channel  
in top arm (See Figure 7), allowing sufficient slack in cables  
for left/Right movement of display and swing arm and also  
swing arm extension and retraction.  
2
1
4. Secure cables to top arm using two cable ties (M).  
5. Repeat steps 1 through 4 for lower arm.  
3
WARNING: IMPROPER INSTALLATION CAN LEAD TO  
SERIOUS PERSONAL INJURY OR DAMAGE TO  
EQUIPMENT! DO NOT route cables through holes in  
faceplate.  
Figure 5  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
PNRIW / PNRIWU  
Installation Instructions  
From Display  
2
x 4  
(A) x 1  
3
1
4
3
2
From Display  
(M) x 4  
Figure 7  
Adjustments  
TENSION ADJUSTMENTS  
Pitch Tension Adjustment  
1. With display mounted, check for desired Pitch tension.  
2. If required, adjust the Centris SelectTM knob right or left until  
desired Pitch tension is obtained. (See Figure 8)  
3. To lock the mount at the desired position, tighten the Pitch  
locking screw. (See Figure 9)  
Centris SelectTM  
Pitch Adjustment Knob  
3
Pitch  
Locking Screw  
2
Figure 9  
Roll Tension Adjustment  
CAUTION: IMPROPER INSTALLATION CAN LEAD TO  
SERIOUS PERSONAL INJURY OR DAMAGE TO  
EQUIPMENT!Overtightening lateral adjustment will cause  
excessive wear and may distort adjustment components.  
1. Using a 9/16” wrench (not provided), slightly tighten or  
loosen lateral Roll tension adjustment nut. (See Figure 10)  
2. Mount the display and check for desired roll tension.  
3. Repeat Steps 1 and 2 until desired Roll tension is obtained.  
Figure 8  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation Instructions  
PNRIW / PNRIWU  
(L) x 1  
1
(K) x 1  
2
Socket Head  
Capscrew  
Figure 11  
4. Using the adjustment wrench (L), turn adjustment bar (K)  
clockwise to increase swing arm tension or  
1
counterclockwise to reduce swing arm tension. (Small  
adjustments of 1/8 turn or less are typically all that is  
required to achieve desired tension.) (See Figure 12) and  
(See Figure 13)  
4
DECREASE  
Roll  
Adjustment Nut  
Figure 10  
Swing Arm Tension Adjustment  
Swing arm tension is pre-set at the factory and is adjusted to  
accommodate displays with weights near the top of the mounts  
capacity.  
If smaller displays are used it may be difficult to reposition the  
display after mounting. Swing arm tension can be adjusted to  
compensate for smaller display by:  
Figure 12  
The display must be mounted prior to adjusting swing arm  
tension.  
1. Locate the adjustment bar (K) and adjustment wrench (L).  
2. Place adjustment bar (K) into socket head cap screw  
located at swing arm pivot point. (See Figure 11)  
4
INCREASE  
NOTE: The display may need to be repositioned in order  
to gain access to the tension adjustment  
screw(s).  
3. Check swing arm tension. If desired tension is present,  
tension adjustment is complete. If additional tension  
adjustment is required, repeat steps 2 thru 4 until desired  
tension is achieved.  
NOTE: If changing from a smaller display to a larger  
display may be necessary to increase swing arm  
tension.  
Figure 13  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
PNRIW / PNRIWU  
Installation Instructions  
USA/International  
Europe  
A
P
F
A
P
F
8401 Eagle Creek Parkway, Savage, MN 55378  
800.582.6480 / 952.894.6280  
877.894.6918 / 952.894.6918  
Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands  
+31 40 2668620  
+31 (0) 40 2668615  
Asia Pacific  
A
Room 30I, Block D, Lily YinDu International Building  
LuoGang, BuJi Town, Shenzhen, CHINA. Post Code: 518112  
8805-000242  
©2007 Chief Manufacturing  
10/07  
P
F
+86-755-8996 9226 ; 8996 9236 ; 8996 9220  
+86-755-8996 9217  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Belkin Network Card F5D6020 User Manual
Black Decker Coffee Grinder PRCBM5 User Manual
Black Decker Planer 3375 User Manual
Bretford Surge Protector EPM User Manual
Briggs Stratton Air Cleaner 31Q700 User Manual
BRK electronic Fire Extinguisher FE1A10GO User Manual
Brunton Two Way Radio ROGER 18 SERIES User Manual
Bushnell Binoculars 202342 User Manual
Chief Manufacturing Indoor Furnishings CM2L40 User Manual
Christie Digital Systems Projector LW600 User Manual