I N S T A L L A T I O N I N S T R U C T I O N S
Instrucciones de instalación
Installationsanleitung
Istruzioni di installazione
Installatie-instructies
Instruções de Instalação
Instructions d´installation
Medium Flat Panel In-Wall Mount
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
MIWRF SERIES
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
MIWRF SERIES
TOOLS REQUIRED FOR INSTALLATION AND PARTS
1/2"
1/8"
7/16"
9/16"
1"
Universal Interface Bracket provided with Models MIWRFUB and MIWRFVB not shown.
I/M
B (2)
x1
A (1)
C (4)
D (4)
E (2)
F (1)
G (2)
F1 (4)
F2 (4)
5/16"
5/16" x 2 1/2"
H (8)
L (4)
J (8)
K (4)
5/16-18
Figure 1
3
Download from Www.Somanuals.com. All Manuals Search And Download.
MIWRF SERIES
Installation Instructions
Installation
Cutout Area
WARNING: IMPROPER INSTALLATION CAN RESULT IN
DEATH OR SERIOUS PERSONAL INJURY! This accessory
should be installed by qualified personnel only.
WARNING: IMPROPER INSTALLATION CAN LEAD TO
MOUNT FALLING CAUSING SEVERE PERSONAL INJURY
OR DAMAGE TO EQUIPMENT! DO NOT deviate from
installation instructions provided. DO NOT substitute
hardware.
The MIW Series is designed to accommodate up to 3 1/2" of
lateral shift adjustment (right or left display offset from center of
studs). This is accomplished by aligning the upper and lower
mounting studs on the housing with either the right hand or left
hand mounting holes in the upper and lower mounting brackets.
(See Figure 3)
15"
IMPORTANT ! : Using the lateral shift feature will impact
the location of J-Box installation on the housing. If
housing lateral shift is used any J-box must be installed
to the side opposite the direction of adjustment.
1. Determine desired mounting location and locate studsusing
a stud finder or similar method.
2. Accurately locate center of studs.
7.65"
3. Determine desired lateral shift required. (See Figure 3)
4. Using a level mark housing opening location on wall using
the dimensions identified. (See Figure 2)
Figure 2
Upper Mounting Bracket
1
1
1
(Display Offset Left)
(Display Offset Right)
3 1/2"
Lower Mounting Bracket
Figure 3
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
MIWRF SERIES
WARNING: ELECTRICAL SHOCK HAZARD! CUTTING
OR DRILLING INTO ELECTRICAL WIRES OR CABLES
CAN CAUSE DEATH OR SERIOUS PERSONAL INJURY!
ALWAYS make certain area behind mounting surfaces is free
of electrical wires and cables before cutting, drilling, or
installing fasteners.
WARNING: IMPROPER INSTALLATION CAN LEAD TO
MOUNT FALLING CAUSING SEVERE PERSONAL INJURY
OR DAMAGE TO EQUIPMENT! Wiring of equipment must
be performed by properly trained and certified persons
following all applicable codes.
8. Slide mount (A) enclosure into opening in wall. (See Figure
5)
WARNING: EXPLOSION AND FIRE HAZARD! CUTTING
OR DRILLING INTO GAS PLUMBING CAN CAUSE DEATH
OR SERIOUS PERSONAL INJURY! ALWAYS make certain
area behind mounting surfaces is free of gas, water, waste, or
any other plumbing before cutting, drilling, or installing
fasteners.
(A) x 1
8
5. Cut drywall on outside edge of lines and remove.
6. Assemble upper and lower mounting rails (B) to mount (A)
in slots that correspond to the desired lateral shift offset
identified during step 3 above using four flanged nuts (K).
(See Figure 3) and (See Figure 4)
(A) x1
(K) x4
6
Figure 5
Place spacers (C) provided between wall and upper and lower
mounting rails (B) if required. (See Figure 6)
(B) x 2
(C) x 4
6
8
(B) x2
Figure 4
7. Install J-box (s) and route all in-wall cables and wiring to
mount encloser keeping in mind and lateral shift offset
determined during step 3 above. (See Figure 3)
Figure 6
9. Secure mount to studs using four flat washers (F2) and four
Lag screws(F1). (See Figure 7)
5
Download from Www.Somanuals.com. All Manuals Search And Download.
MIWRF SERIES
Installation Instructions
Cover and Trim Installation
Cover Installation
To install covers:
(F1) x4
(F2) x4
1. Install upper and lower wall channel covers (E) by tipping
cover top down and positioning as shown in end view of
figure below. (See Figure 8)
2. Tap firmly across bottom of channels to lock in place as
shown in figure below. (See Figure 8)
3. Install four R.H. and L.H. end caps (D) by aligning tabs on
end caps (F) with slots in wall channel covers (E) and sliding
tabs in until end caps (D) are flush with wall channel covers
(E). (See Figure 8)
9
(A) x1
9
Figure 7
2
(E) x 2
(D) x 4
1
1
2
1
2
Figure 8
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
MIWRF SERIES
To install display:
Trim Installation
To install optional trim;
1. Install interface bracket (if model MIWRFUB or MIWRFVB)
following the installation instructions provided with the
interface bracket.
2. Move mount faceplate to extended position by grasping
faceplate and pulling outward away from wall.
(See Figure 10)
1. Orient two trim pieces (G) as shown in figure below.
(See Figure 9)
2. Slide slat in trim edge over lip in mount enclosure and press
trim (G) onto enclosure. (See Figure 9)
3. While supporting both sides of display, align four mounting
buttons on display or interface bracket with four mounting
holes in faceplate. (See Figure 10)
(G) x 2
4. Lower display into place listening for audible "click" to
ensure recessed area of mounting buttons are properly
seated in lower area of mounting holes and "click lock"
mechanism has engaged. (See Figure 10) and
(See Figure 11)
4
2
1
2
3
Figure 9
Figure 10
Display Installation
NOTE: Holes are provided in the faceplate for use with a
padlock or similar locking device, if desired. In addition,
the pin and nut may be removed from the upper holes
and moved to the lower holes for use as a more
permanent locking device. (See Figure 11)
WARNING: IMPROPER INSTALLATION CAN LEAD TO
MOUNT FALLING CAUSING SEVERE PERSONAL INJURY
OR DAMAGE TO EQUIPMENT! DO NOT install display in a
manner other than that specified by the manufacturer. Certain
displays may require the use of an interface bracket for
proper installation of the display. If an interface bracket is not
installed, or there are any other questions regarding the
installation of the display, immediately contact a Chief
Customer Service representative by calling 800-582-6480 or
by visiting www.chiefmfg.com.
Remove pin
4
and nuts and
move to lower holes.
WARNING: IMPROPER INSTALLATION CAN LEAD TO
MOUNT FALLING CAUSING SEVERE PERSONAL INJURY
OR DAMAGE TO EQUIPMENT. Displays can weigh in
excess of 40 lbs (18.1kg). ALWAYS use two people and
proper lifting techniques when installing display.
5
WARNING: IMPROPER INSTALLATION CAN LEAD TO
MOUNT FALLING CAUSING SEVERE PERSONAL INJURY
OR DAMAGE TO EQUIPMENT. Make sure mounting buttons
on display are properly seated in mounting holes in faceplate.
A padlock or bolt may
be placed through latch
holes
Figure 11
7
Download from Www.Somanuals.com. All Manuals Search And Download.
MIWRF SERIES
Installation Instructions
CABLE MANAGEMENT
ADJUSTMENTS
Pitch Tension Adjustment
WARNING: IMPROPER INSTALLATION CAN LEAD TO
SERIOUS PERSONAL INJURY OR DAMAGE TO
EQUIPMENT! Make sure cables do not run through pinch
points.
To adjust display pitch tension:
1. With display installed, tighten or loosen two screws, one on
each side. (See Figure 14)
2. Check for desired tension.
3. Repeat Steps 1 and 2 until desired tension is obtained.
1. Locate and install cable tie clips (J) where desired for proper
cable routing. (See Figure 12)
1
1
(J) x 8
Figure 12
2. Route cables down arms on mount. (See Figure 13)
3. Position cable covers (L) over arm and cable and press
cable covers (L) down on to arms to secure cables.
(See Figure 13)
WARNING: IMPROPER INSTALLATION CAN LEAD TO
SERIOUS PERSONAL INJURY OR DAMAGE TO
EQUIPMENT! DO NOT route cables through holes in
faceplate.
Figure 14
Roll Adjustment
The mount allows for the horizontal alignment (Roll) of the
display to be adjusted up to 2 deg. right or left to level the
display after installing.
2
To adjust Roll:
3
1. Loosen the roll tension adjustment nut located on the back
side of the faceplate assembly. (See Figure 15)
2. Level display.
NOTE: If display will not level slightly loosen top nut as well.
3. Tighten roll tension adjustment nut. (See Figure 15)
(L) x 4
From Display
Figure 13
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
MIWRF SERIES
2
1
1
(on back side
in this view)
3
2
Figure 16
Display Height Adjustment
The mount is designed to accommodate up to 1" of display
height adjustment.
To adjust display height:
1. With display installed, loosen adjustment locking screw
using hex wrench. (See Figure 17)
2. Adjust display height by turning adjustment nut in desired
direction. (See Figure 17)
Figure 15
Extend/Retract Tension Adjustment
3. Tighten adjustment locking screw when display is at desired
height. (See Figure 17)
Arm Extend and Retract tension is pre-set at the factory and is
adjusted to accommodate displays with weights near the top of
the mounts capacity.
If smaller displays are used it may be difficult to reposition the
display after mounting. Arm Extend and Retract tension can be
adjusted to compensate for smaller display by:
1
3
The display must be mounted prior to adjusting swing arm
tension.
1. With display installed, tighten or loosen adjustment screw
using hex wrench. (See Figure 16)
2. Check for desired tension.
3. Repeat Steps 1 and 2 until desired tension is obtained.
NOTE: If changing from a smaller display to a larger display
may be necessary to increase tension.
2
Figure 17
9
Download from Www.Somanuals.com. All Manuals Search And Download.
MIWRF SERIES
Installation Instructions
YAW Tension Adjustment
The mount is designed to accommodate up to 37.5 deg. of
travel to left and right of center.
To adjust YAW tension:
1. With display installed, loosen adjustment screw using hex
wrench. (See Figure 18)
2. Check for desired tension.
3. Repeat Steps 1 and 2 until desired tension is obtained.
NOTE: If changing from a smaller display to a larger display
may be necessary to increase tension.
1
3
TOP VIEW
Figure 18
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
MIWRF SERIES
DIMENSIONS
11
Download from Www.Somanuals.com. All Manuals Search And Download.
MIWRF SERIES
Installation Instructions
USA/International
Europe
A
P
F
A
P
F
8401 Eagle Creek Parkway, Savage, MN 55378
800.582.6480 / 952.894.6280
877.894.6918 / 952.894.6918
Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands
+31 (0)40 2668620
Chief Manufacturing, a products division
of Milestone AV Technologies
+31 (0)40 2668615
Asia Pacific
A
Room 24F, Block D, Lily YinDu International Building
LuoGang, BuJi Town, Shenzhen, CHINA.
8805-000249 Rev A
¤2008 Milestone AV Technologies
11/08
P
F
+86-755-8996 9226
+86-755-8996 9217
Download from Www.Somanuals.com. All Manuals Search And Download.
|