I N S T A L L A T I O N I N S T R U C T I O N S
Instrucciones de instalación
Installationsanleitung
Istruzioni di installazione
Installatie-instructies
Instruções de Instalação
Instructions d´installation
JWD
JWP
JWS
Medium Flat Panel Wall Mount
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
J-Series
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
J-Series
DIMENSIONS
JWS
332.93
13.11
300.97
11.85
80.36
3.16
152.40
6.00
81.77
3.22
100
3.94
100
3.94
139.62
5.50
292.47
11.51
215.36
8.48
120.65
4.75
175.87
6.92
JWD
516.87
20.35
307.72
12.11
215.90
8.50
215.90
8.50
152.40
6.00
81.77
3.22
68.25
2.69
231.52
9.11
26.20
1.03
100
3.94
100
3.94
220.66
8.69
373.33
14.70
120.65
4.75
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
J-Series
LEGEND
Tighten Fastener
Pencil Mark
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Potloodmerkteken
Marquage au crayon
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Drill Hole
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Percez un trou
Phillips Screwdriver
Adjust
Destornillador Phillips
Ajustar
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Remove
Quitar
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Entfernen
Remover
Rimuovere
Verwijderen
Retirez
Clé à fourche
By Hand
Optional
Opcional
Optional
Opcional
Opzionale
Optie
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main
En option
Hex-Head Wrench
Security Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Llave de seguridad
Sicherheitsschlüssel
Chave de segurança
Chiave di sicurezza
Veiligheidssleutel
Clé de sécurité
Zeskantsleutel
Clé à tête hexagonale
4
Download from Www.Somanuals.com. All Manuals Search And Download.
J-Series
Installation Instructions
TOOLS REQUIRED FOR INSTALLATION
#2
1/8"
PARTS
A
B
I/M
E
x1
D
Interface
Bracket
C
Kit
(Including Hardware)
G
F
x 1
Table 1: Parts
QUANTITY By
MODEL
ITEM DESCRIPTION
JWP JWS JWD
A
B
C
D
E
F
PIVOT PITCH WALL MOUNT
SINGLE ARM WALL MOUNT
DUAL ARM WALL MOUNT
J-SERIES WALL PLATE
1
-
-
-
1
-
-
-
1
1
2
2
4
1
-
1
1
2
2
CABLE MANAGEMENT COVER
HEX HEAD LAG SCREW, 3/8" X 3"
2
-
G
PHILLIPS FLAT MACHINE SCREW, 8-32 X 3/8"
5
Download from Www.Somanuals.com. All Manuals Search And Download.
J-Series
Installation Instructions
INSTALLATION
WARNING: FAILURE TO PROVIDE ADEQUATE
STRUCTURAL STRENGTH FOR THIS MOUNT CAN
RESULT IN SERIOUS PERSONAL INJURY OR DAMAGE
TO EQUIPMENT! It is the installer’s responsibility to make
sure the structure to which this mount is attached can support
five times the combined weight of the mount and all
equipment attached to it. Reinforce the structure as required
before installing the mount.
(D)
(A, B or C)
5
1. Determine location for mount keeping in mind display size,
extension, height adjustment (if applicable), and pitch/roll
requirements.
NOTE: Wall plate (D) MUST be installed into wood stud.
2. Using wall plate (D) as a template, mark then drill two 1/8"
diameter pilot holes through top and bottom holes of wall
bracket into wall structure. (See Figure 1)
6
(F) x 2
3
2
Figure 2
7. Tighten set screw in bottom of wall mount. (See Figure 3)
NOTE: Ensure set screw engages on back side of wall plate to
properly secure wall mount.
(A, B or C)
(D)
Figure 1
3. Install two 3/8" x 3" hex head lag screws (F) through wall
plate (D) and drywall into wood stud. (See Figure 1)
4. Ensure wall plate (D) is vertical, then tighten screws (D).
Set
Screw
7
CAUTION: Overtightening screws may cause wall bracket
to compress into soft wall surface, resulting in difficult mount
installation or improper engaging of set screw in later step.
Figure 3
5. Insert top of wall mount (A, B or C) over lip on top of wall
plate (D). (See Figure 2)
6. Swing wall mount down flush against wall.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
J-Series
DISPLAY INSTALLATION
1. Determine mounting pattern on display.
WARNING: IMPROPER INSTALLATION CAN LEAD TO
EQUIPMENT FALLING CAUSING SERIOUS PERSONAL
INJURY AND DAMAGE TO EQUIPMENT! DO NOT
substitute hardware. Use only hardware supplied by
manufacturer!
1
WARNING: IMPROPER INSTALLATION CAN LEAD TO
ELECTRIC SHOCK OR DAMAGE TO EQUIPMENT! Screw
length must not exceed the depth of threaded mounting insert
in display.
WARNING: OVERTIGHTENING OF SCREWS CAN
DAMAGE PARTS AND LEAD TO SERIOUS PERSONAL
INJURY AND DAMAGE TO EQUIPMENT! DO NOT over
tighten screws when installing interface bracket.
x2
NOTE: If the display being installed has a 100x100 VESA
mounting pattern, no interface bracket is required and
the display can be mounted directly to the mounting
plate as outlined below.
Figure 4
2. Align two screws in display back with upper teardrop
mounting holes in mounting plate and lower display until
screws are seated in lower area of teardrop mounting holes.
(See Figure 5)
NOTE: If the display being installed requires an interface
bracket, refer to the interface bracket installation
instructions.
WARNING: IMPROPER INSTALLATION CAN LEAD TO
DISPLAY FALLING CAUSING SERIOUS PERSONAL
INJURY OR DAMAGE TO EQUIPMENT! Using screws of
improper size may damage your display! Proper screws will
easily and completely thread into display mounting holes.
Ensure that screws are not too long.
2
(A, B or C)
WARNING: IMPROPER INSTALLATION CAN LEAD TO
DISPLAY FALLING CAUSING SERIOUS PERSONAL
INJURY OR DAMAGE TO EQUIPMENT! Inadequate thread
engagement in display may cause display to fall! Back out
screws ONLY as necessary to allow installation of mounting
plate!
1. Start two M4 x 8mm Phillips pan head screws (included in
hardware kit) into upper mounting holes in display back.
(See Figure 4)
NOTE: Leave at least 1/8" of each screw protruding out back
of display.
Figure 5
3. Install two more of the same screws through lower mounting
holes in display mounting plate and into display back.
(See Figure 6)
7
Download from Www.Somanuals.com. All Manuals Search And Download.
J-Series
Installation Instructions
ADJUSTMENTS
Swing Arm
x 2
3
PIVOT / SWING TENSION
1. Slightly loosen or tighten the adjustment screw(s) as
necessary (See Figure 8).
1
Figure 8
Figure 6
4. Tighten all hardware.
DISPLAY ROLL / PITCH / YAW TENSION:
CABLE MANAGEMENT
1. Disconnect all wires and cable from the display.
2. Remove two Lower screws securing display to Centris cup.
3. Loosen two Upper screws securing display.
4. Lift display upward and away from mount.
1. Attach all cables to display.
CAUTION: Ensure that adequate cable slack exists for
movement of display, and that cables will not be pinched by
installation of cable management cover(s) (E) or screws (G).
5. Turn the tension adjustment screw clockwise to increase
tension, or counter-clockwise to decrease tension.
(See Figure 9)
2. Carefully insert cables in cavity located in lower portion of
mount arm (See Figure 7).
3. Install cover (E) with two 8-32 x 3/8" Phillips screws (G).
(See Figure 7)
Cable Path
(typical)
2
(E) x 1 (JWS)
(E) x 2 (JWD)
5
(G) x 2 (JWS)
3
(G) x 4 (JWD)
Figure 9
Figure 7
Re-install display.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
J-Series
9
Download from Www.Somanuals.com. All Manuals Search And Download.
J-Series
Installation Instructions
USA/International
Europe
A
P
F
A
P
F
8401 Eagle Creek Parkway, Savage, MN 55378
800.582.6480 / 952.894.6280
877.894.6918 / 952.894.6918
Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands
+31 (0)40 2668620
+31 (0)40 2668615
Chief Manufacturing, a division of
Milestone AV Technologies
Asia Pacific
A
Room 24F, Block D, Lily YinDu International Building
LuoGang, BuJi Town, Shenzhen, CHINA.
8832-000253
P
F
+86-755-8996 9226
+86-755-8996 9217
¤2008 Milestone AV Technologies
06/08
Download from Www.Somanuals.com. All Manuals Search And Download.
|