IN STAL LA TIO N I NST RUCT IONS
Small Flat Panel Lift Arm
FSA-1004 and KSA-1004
The Lift Arm FSA/KSA-1004 is an accessory that can be
used with a broad range of Small Flat Panel Displays.
Lift Arm
The FSA/KSA-1004 allows the user to move a display
vertically up or down in a 13 inch radius. The lift arm can
be moved vertically 6-1/2” up from center and 6-1/2”
down from center.
The FSA/KSA-1004 is designed to safely hold a display
weighing up to 25 lbs. (11.3kg). The display can be up to
30 inches wide.
The FSA/KSA-1004 accommodates all VESA®
75mm/100mm compliant displays.
BEFORE YOU BEGIN
x
CAUTION: To prevent damage to the mount, which could affect or void the Factory warranty, thoroughly
study all instructions and illustrations before you begin to install the mount brackets. Pay particular atten-
tion to the “Important Precautions” on Page 2.
x
If you have any questions about this installation, contact Chief Manufacturing at 1-800-582-6480 or 952-582-6480.
CHIEF MANUFACTURING INC.
8832-000041 Rev. F
©2007 Chief Manufacturing
03/07
1-800-582-6480 952-894-6280 FAX 952-894-6918
8401 EAGLE CREEK PARKWAY, STE. 700
SAVAGE, MINNESOTA 55378 USA
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
FSA/KSA-1004
PARTS
Tension
adjustment bolt
70
70
50
30
50
70
70
10
30
20
40
80
20
60
Figure 1. Lift Arm Installation Drawing
PARTS LIST
Table 1. Lift Arm Parts
DESCRIPTION
PART
10
QTY
LIFT ARM
1
2
2
1
2
1
4
1
20
WASHER, UHMW, .640 ID X .845 OD
WASHER, UHMWPE, .318 ID X .031 OD
PIVOT PIN, SPF
30
40
50
CAPSCREW, BUTTON HEAD
LOCK NUT, NYLOCK
60
70
SPACER, STAINLESS STEEL, .320 X .018
LARGE LOCK NUT, NYLOCK
80
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
FSA/KSA-1004
INSTALLATION
Adding a lift arm modifies your mount configuration. This
procedure applies to most small flat panel displays,
particularly those with a pivot or swing arm, whether wall
mount or desk mount.
3. To remove the pivot pin (see Figure 2) from the other
end, do the following:
a. If the mount is a pivot/pitch wall mount, remove
the attaching hardware from the display.
b. If the mount is wall mounted, desk mounted, or
has more than one swing arm, remove the
attaching hardware from the arm closest to the
display.
Removing the Display from the Mount
To remove the display from its mount, perform the
following steps:
NOTE: Do not remove the four screws (not shown) that
NOTE: The two button head cap screws removed from
the mount will be replaced with longer screws
when the lift arm is installed.
attach the display to the interface bracket.
1. Disconnect the power/audio/video cables from the
display (not shown).
NOTE: Keep the pivot pin removed in step 2. This part
will be used again when the lift arm is installed.
2. Remove the cap screw, washers, pivot pin, and
retaining nut from the display end of the mount.
Refer to Figure 2. Separate the display from the
mount.
Cap screw
Small
Washer
Display Mount Parts — Typical
PART NAME
SCREW, CAP
QTY
2
Pivot Pin
WASHER, FLAT
4
SMALL WASHER, NYLON
LARGE WASHER, NYLON
NUT, NYLOCK
2
Flat Washers
Large
Washer
2
2
Nut
Figure 2. Single Swing Arm (FWS-110) — Example
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
FSA/KSA-1004
Installing display end of lift arm
Installing the Lift Arm
1. Install the original pivot pin (see Figure 3) that was
retained when the display was removed and a
washer (20) onto the base of the mount.
To install the lift arm, perform the following procedures:
Installing base end of lift arm
2. Assemble a button head cap screw (50), one
stainless steel washer (70), washer (30), and a
second stainless steel washer (70) onto button head
cap screw (50) as shown in Figure 3.
1. Locate the tension adjustment bolt on the lift arm
(see Figure 3). Install the pivot pin (40) and a washer
(20) onto the base of the mount.
2. Assemble a button head cap screw (50), one
stainless steel washer (70), washer (30), and a
second stainless steel washer (70) onto button head
cap screw (50) as shown in Figure 3.
3. Insert the screw assembly (step 2) into the pivot hole
on the lift arm (10) and the display end of the mount.
4. Thread the lock nut (80) to the screw assembly (step
2) at the bottom of the mount.
3. Insert the screw assembly (step 2) into the pivot hole
on the lift arm (10) and the base end of the mount.
CAUTION: Over-tightening a tension screw (50) will
cause excessive wear and may distort
adjustment components.
4. Thread the lock nut (60) to the screw assembly (step
2) at the bottom of the mount.
5. Using the 3/16” hex key (provided), tighten the
button head cap screw (50) into the nut (80) several
turns, leaving flexibility in the hinged joint. Do not
over-tighten the cap screw (50).
CAUTION: Over-tightening a tension screw (50) will
cause excessive wear and may distort
adjustment components.
5. Using the 3/16” hex key (provided), tighten the
button head cap screw (50) into the nut (60) several
turns, leaving flexibility in the hinged joint. Do not
over-tighten the cap screw (50).
Lift Arm Parts
ITEM
10
20
30
40
50
60
70
80
PART NAME
QTY
1
50
30
LIFT ARM
LARGE WASHER, NYLON
SMALL WASHER, NYLON
PIVOT PIN, SPF
2
2
1
50
Original
Pivot
Pin
CAP SCREW, BUTTON HEAD
LOCK NUT, NYLOCK
2
1
70
SPACER, STAINLESS STEEL
LARGE LOCK NUT, NYLOCK
4
20
80
1
40
10
20
60
Figure 3. Installing Lift Arm
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
FSA/KSA-1004
Lateral
Adjusting Lateral Movement
Tension
Adjustment
Bolts
CAUTION: Over-tightening tension bolt will cause
excessive wear and may distort adjustment
components.
(Typical)
To adjust the lateral movement tension, perform the
following procedures:
1. Slightly tighten or loosen the tension adjustment bolt.
2. Check for desired tension. Repeat as necessary.
Adjusting Lift Arm Tension
CAUTION: Over-tightening tension bolt will cause
excessive wear and may distort adjustment
components.
Adjusting Lateral Movement
To adjust the tension of the lift arm:
1. Raise or lower the lift arm until tension adjustment
bolt appears in the opening.
Lift Arm Tension
Adjustment Bolt
2. Using the 5/32” hex key (provided), adjust the
tension adjustment bolt, as follows:
NOTE: There is no fixed number of revolutions to turn
the tension adjustment bolt. Tighten or loosen
the bolt, as needed. When the bolt is adjusted
correctly, the display can be easily raised or
lowered at any time, and stay in place without
sagging.
a. To increase lift arm tension, turn the tension
adjustment bolt counterclockwise.
Adjusting Lift Arm Tension
b. To decrease lift arm tension, turn the tension
adjustment bolt clockwise.
3. Raise or lower the lift arm to check for desired
tension. Repeat step 2 as needed.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
FSA/KSA-1004
7
Download from Www.Somanuals.com. All Manuals Search And Download.
|