HALOGEN FLOOR SHOP LIGHT
30858
ASSEMBLY & OPERATING INSTRUCTIONS
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
Copyright© 2005 by Harbor Freight Tools®. All rights reserved. No portion of this manual or
any artwork contained herein may be reproduced in any shape or form without the
express written consent of Harbor Freight Tools.
For technical questions and replacement parts please call 1-800-444-3353.
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRICAL SAFETY
4.
5.
Grounded lights must be plugged into an outlet properly installed and grounded in ac-
cordance with all codes and ordinances. Never remove the grounding prong or mod-
ify the plug in any way. Do not use any adapter plugs. Check with a qualified elec-
trician if you are in doubt as to whether the outlet is properly grounded. If the tools
should electrically malfunction or break down, grounding provides a low resistance path to
carry electricity away from the user.
Double insulated lights are equipped with a polarized plug (one blade is wider than
the other). This plug will fit in a polarized outlet only one way. If the plug does not fit
fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician
to install a polarized outlet. Do not change the plug in any way. Double insulation elimi-
nates the need for the three wire grounded power cord and grounded power supply system.
6.
7.
8.
Avoid body contact with grounded surfaces such as pipes, radiators, ranges, and
refrigerators. There is an increased risk of electric shock if your body is grounded.
Do not expose the Halogen Light to rain or wet conditions. Water entering a power tool
will increase the risk of electric shock.
Do not abuse the Power Cord. Never use the Power Cord to carry the light or pull the
Plug from an outlet. Keep the Power Cord away from heat, oil, sharp edges, or moving
parts. Replace damaged Power Cords immediately. Damaged Power Cords increase
the risk of electric shock.
9.
When operating a light outside, use an outdoor extension cord marked “W-A” or “W”.
These extension cords are rated for outdoor use, and reduce the risk of electricshock.
PERSONAL SAFETY
10.
Stay alert. Watch what you are doing, and use common sense when operating the
Halogen Light. Do not use the Halogen Light while tired or under the influence of
drugs, alcohol, or medication. A moment of inattention while operating the light may
result in serious personal injury.
11.
12.
Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your
hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or long hair
can be caught in moving parts.
Avoid accidental starting. Be sure the Power Switch is off before plugging in.
Carrying the Light with your finger on the Power Switch, or plugging in the light with
the Power Switch on, invites accidents.
13.
14.
Remove adjusting keys or wrenches before turning the Halogen Light on. A wrench or
a key that is left attached to a rotating part of the light may result in personal injury.
Do not overreach. Keep proper footing and balance at all times. Proper footing and
balance enables better control of the Halogen Light in unexpected situations.
SKU 30858
For technical questions please call 1-800-444-3353.
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
15.
16.
Use safety equipment. Always wear eye protection.
LIGHT USE AND CARE
Do not force the Halogen Light. Use the correct light for your application. The correct
light will do the job better and safer at the rate for which it is designed.
17.
18.
Do not use the light if the On/Off Switch does not turn it on or off.
Disconnect the Power Cord Plug from the power source before making any adjust-
ments, changing accessories, or storing the tool. Such preventive safety measures
reduce the risk of starting the tool accidentally.
19.
20.
21.
Store the Light out of reach of children and other untrained persons. The Halogen
Light is dangerous in the hands of untrained users.
Maintain the Light with care. Do not use a damaged light. Tag damaged light “Do not
use” until repaired.
Check for misalignment or binding of moving parts, breakage of parts, and any other
condition that may affect the light’s operation. If damaged, have the light serviced
before using. Many accidents are caused by poorly maintained lights.
22.
Use only accessories that are recommended by the manufacturer for your model.
Accessories that may be suitable for one tool may become hazardous when used on
another light.
SERVICE
23.
24.
Light service must be performed only by qualified repair personnel. Service or mainte-
nance performed by unqualified personnel could result in a risk of injury.
When servicing a light, use only identical replacement parts. Follow instructions in
the “Inspection, Maintenance, And Cleaning” section of this manual. Use of unauthor-
ized parts or failure to follow maintenance instructions may create a risk of electric shock or
injury.
GROUNDING
WARNING!
Improperly connecting the grounding wire can result in the risk of electric shock. Check with
a qualified electrician if you are in doubt as to whether the outlet is properly grounded. Do
not modify the power cord plug provided with the Light. Never remove the grounding prong
from the plug. Do not use the Light if the power cord or plug is damaged. If damaged, have
it repaired by a service facility before use. If the plug will not fit the outlet, have a proper
outlet installed by a qualified electrician.
SKU 30858
For technical questions please call 1-800-444-3353.
Page 4
Download from Www.Somanuals.com. All Manuals Search And Download.
GROUNDED TOOLS:TOOLS WITH THREE PRONG PLUGS
Note: The Light has a Three Prong Plug.
1.
2.
3.
Tools marked with “Grounding Required” have a three wire cord and three prong grounding
plug. The plug must be connected to a properly grounded outlet. If the Light
should electrically malfunction or break down, grounding provides a low resistance path to
carry electricity away from the user, reducing the risk of electric shock. (See Figure A.)
The grounding prong in the plug is connected through the green wire inside the cord to the
grounding system in the tool. The green wire in the cord must be the only wire connected to
the Light’s grounding system and must never be attached to an electrically “live” terminal.
(See Figure A.)
A grounded appliance must be plugged into an appropriate outlet, properly installed and
grounded in accordance with all codes and ordinances. The plug and outlet should look like
those in the following illustration. (See Figure A.)
Figure A
DOUBLE INSULATED APPLIANCES: APPLIANCES WITH TWO PRONG PLUGS
1.
2.
Appliances marked “Double Insulated” do not require grounding. They have a special double
insulation system which satisfies OSHA requirements and complies with the applicable
standards of Underwriters Laboratories, Inc., the Canadian Standard Association, and the
National Electrical Code. (See Figure B.)
Double insulated tools may be used in either of the 120 volt outlets shown in the following
illustration. (See Figure B.)
Figure B
SKU 30858
For technical questions please call 1-800-444-3353.
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
EXTENSION CORDS
1.
2.
Grounded appliances require a three wire extension cord. Double Insulated products can
use either a two or three wire extension cord.
As the distance from the supply outlet increases, you must use a heavier gauge extension
cord. Using extension cords with inadequately sized wire causes a serious drop in voltage,
resulting in loss of power and possible tool damage. (See Figure C, next page.)
3.
4.
5.
6.
7.
The smaller the gauge number of the wire, the greater the capacity of the cord. For
example, a 14 gauge cord can carry a higher current than a 16 gauge cord. (See Figure C.)
When using more than one extension cord to make up the total length, make sure each cord
contains at least the minimum wire size required. (See Figure C.)
If you are using one extension cord for more than one tool, add the nameplate amperes and
use the sum to determine the required minimum cord size. (See Figure C.)
If you are using an extension cord outdoors, make sure it is marked with the suffix “W-A”
(“W” in Canada) to indicate it is acceptable for outdoor use.
Make sure your extension cord is properly wired and in good electrical condition. Always
replace a damaged extension cord or have it repaired by a qualified electrician before using
it.
8.
Protect your extension cords from sharp objects, excessive heat, and damp or wet areas.
Figure C
SKU 30858
For technical questions please call 1-800-444-3353.
Page 6
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFIC SAFETY RULES
1.
2.
WARNING! Do not mount the Halogen Light on or in any residential structure. Mounting
in such a location creates a fire hazard that can result in property damage, severe personal
injury, and/or death.
ALWAYS point the Light away from the wall, whether the unit is in use or not. If the
light is accidentally pointed at the wall while it is on or while it is still hot when turned off, a
fire may result.
3.
4.
5.
6.
7.
Keep all flammable materials and wall hangings at least 10 feet from the mounting
location.
Make sure to turn off the Halogen Light and unplug the unit from its electrical outlet
when unattended.
Immediately upon turning on the Halogen Light, the Halogen Bulb become VERY
hot. While operating the unit, do not touch the Halogen Bulb, or grid.
Avoid excessive UV radiation. Should your skin begin to feel hot while operating the
Halogen Light, immediately remove yourself from the unit’s light rays.
Avoid serious eye injury. Do not look directly into the Halogen Bulb when operating this
product. Always wear ANSI approved safety goggles when working with tools and
equipment.
8.
Do not touch the Halogen Bulb at any time. Oil from skin will drastically shorten the
bulb’s life-span if not cleaned (with rubbing alcohol) before use. Handle with a soft, clean
cloth instead.
9.
Do not operate the Light with a missing or damaged Lens or Grid.
Do not operate the Halogen Light with the Grid open.
10.
11.
Turn off the Halogen Light, unplug its Power Cord from its 120 volt, grounded,
electrical outlet, and allow it to completely cool down prior to performing any
inspection, maintenance, or cleaning on the unit.
12.
After its use, make sure to allow the Light to completely cool down before storing the
unit.
13.
14.
Do not obstruct walkways or common areas with the cord.
The Light is weatherproof but not waterproof. Do not submerge the Light in water.
SKU 30858
For technical questions please call 1-800-444-3353.
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
SYMBOLOGY
Double Insulated
Canadian Standards
Association
Underwriters
Laboratories, Inc.
Volts Alternating Current
V ~
Amperes
A
n
No Load Revolutions
Per Minute (RPM)
o
xxxx/min.
WARNING! The warnings, precautions, and instructions discussed in this manual cannot
cover all possible conditions and situations that may occur. The operator must understand
that common sense and caution are factors which cannot be built into this product, but
must be supplied by the operator.
Unpacking
When unpacking the Halogen Floor Shop Light, check to make sure parts on page 10 are included.
If any parts are missing or broken, please call HARBOR FREIGHT TOOLS at 1-800-444-3353.
Assembly
Your Halogen Floor Shop Light will require some minor assembly. The Light requires special
conditions for set up and operation. It is important that you read the entire manual to become
familiar with the product BEFORE you use the Light.
1.
2.
Slide the Halogen Lamp onto the Steel Stand (4). Place the Mounting Bracket on the Light
onto the Steel Stand (4) and thread in the Knob (1).
Loosen the Knob (1) to pivot the Light. The Light Pivots 180 degrees up and down. To pivot
the Light, move it by the Handle at the top of the Steel Stand. NEVER touch the Halogen
Light to move it or pivot it.
Bulb Replacement
1.
Make certain that the product is OFF and unplugged. With leather gloves on, squeeze and
remove the Grid from the front of the Light.
2.
3.
4.
Remove the Bolt from the top of the Light.
Pull out the Lens from the front of the Light.
Make certain that the Halogen Bulb (3) has had sufficient time to cool. Gently pull out the
Halogen Bulb.
SKU 30858
For technical questions please call 1-800-444-3353.
Page 8
Download from Www.Somanuals.com. All Manuals Search And Download.
5.
6.
1.
Making certain NOT TO TOUCH the new Halogen Bulb (3), insert it into the Light left side
first.
Do not touch the Halogen Bulb at any time. Oil from skin will drastically shorten the
bulb’s life-span if not cleaned (with rubbing alcohol) before use. Handle with a soft, clean
cloth instead.
Insert the Bolt (2) and replace the Grid.
Operation
To turn on the Light, plug the Power Cord into a 120 volt, grounded, electrical outlet.
WARNING! Always point the light away from the wall, whether the unit is in use or not. If
the unit is accidentally pointed at the wall while turned on or still hot
after turned off, a fire may result.
2.
Unplug the light to turn it off.
Inspection, Maintenance and Cleaning
1.
2.
Always unplug the Halogen Light from its electrical outlet and allow the unit to
completely cool down before performing any inspection, maintenance, or cleaning.
Before each use: Inspect the general condition of the Halogen Light. Check for
misalignment or binding of moving parts, cracked or broken parts, damaged Power Cord,
damaged Grid, Lens and any other condition that may affect its safe operation. If a problem
occurs with the Light, have the problem corrected before further use. Do not use damaged
equipment.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDEDTHE PARTS DIAGRAM INTHIS MANUAL AS A REFERENCETOOL
ONLY. NEITHERTHE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KINDTO
THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED
TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES
THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS
AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE
ORIGINAL PRODUCT OR REPLACEMENT PARTSTHERETO,OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT
PARTS THERETO.
SKU 30858
For technical questions please call 1-800-444-3353.
Page 9
REV 12/06
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts List
Part
1
Description
Q’ty
1
Knob
Bolt
2
1
3
Halogen Bulb
Steel Stand
Light Housing w/cord
Grid
1
4
1
5
1
6
1
2
5
3
6
4
1
SKU 30858
For technical questions please call 1-800-444-3353.
Page 10
Download from Www.Somanuals.com. All Manuals Search And Download.
|