MULTI-FUNCTION POWER TOOL
67256
SET UP aNd OPERaTINg INSTRUCTIONS
Read this material before using this product.
Failure to do so can result in serious injury.
SaVE ThIS MaNUaL.
©
®
Copyright 2009 by Harbor Freight Tools . All rights reserved. No portion of this manual or any artwork
contained herein may be reproduced in any shape or form without the express written consent of
Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein. Tools required for
assembly and service may not be included.
For technical questions or replacement parts, please call 1-800-444-3353.
Revised Manual 10k
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Electrical safety
moment of inattention while operating
power tools may result in serious
personal injury.
a.Power tool Plugs must match the
outlet. Never modify the Plug in
any way. do not use any adapter
plugs with grounded power tools.
Unmodified plugs and matching
outlets will reduce risk of electric
shock.
b.Use personal protective
equipment. always wear aNSI-
approved safety goggles. Safety
equipment such as NIOSH-approved
dust mask/respirator, NIOSH-
approved hearing protection, and
heavy duty work gloves will reduce
personal injuries.
b.avoid body contact with grounded
surfaces such as pipes, radiators,
ranges and refrigerators. There is
an increased risk of electric shock if
your body is grounded.
c.Prevent unintentional starting.
Ensure the Power Switch is in the
off-position before connecting to
the power source or picking up or
carrying the tool. Carrying power
tools with your finger on the Power
Switch invites accidents.
c.do not expose power tools to rain
or wet conditions. Water entering
a power tool will increase the risk of
electric shock.
d.do not abuse the Power Cord.
Never use the Cord for carrying,
pulling or unplugging the power
tool. Keep Cord away from
d.Remove any adjusting key or
wrench before turning the power
tool on. A wrench or a key left
attached to an oscillating part of the
power tool may result in personal
injury.
heat, oil, sharp edges or moving
parts. Damaged or entangled cords
increase the risk of electric shock.
e.do not overreach. Keep proper
footing and balance at all times.
This enables better control of the
power tool in unexpected situations.
e.When operating a power tool
outdoors, use an extension cord
suitable for outdoor use. Use of a
cord suitable for outdoor use reduces
the risk of electric shock.
f. dress properly. do not wear loose
clothing or jewelry. Keep your
hair, clothing and gloves away
from moving parts. Loose clothes,
jewelry or long hair can be caught in
moving parts.
f. If operating a power tool in a damp
location is unavoidable, use a
ground Fault Circuit Interrupter
(gFCI) protected supply. Use of
a GFCI reduces the risk of electric
shock.
4. Power tool use and care
3. Personal safety
a.do not force the power tool. Use
the correct power tool for your
application. The correct power tool
will do the job better and safer at the
rate for which it was designed.
a.Stay alert, watch what you are
doing and use common sense
when operating a power tool. do
not use a power tool while you
are tired or under the influence of
drugs, alcohol or medication. A
b.do not use the power tool if the
Power Switch does not turn it on
SKU 67256
For technical questions, please call 1-800-444-3353.
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
and off. Any power tool that cannot
be controlled with the Switch is
dangerous and must be repaired.
only identical replacement parts.
This will ensure that the safety of the
power tool is maintained.
c.disconnect the Power Cord from
the power source before making
any adjustments, changing
Specific Safety Warnings
1. Maintain labels and nameplates on
the power tool. These carry important
safety information. If unreadable or
missing, contact Harbor Freight Tools
for a replacement.
accessories, or storing the power
tool. Such preventive safety
measures reduce the risk of starting
the power tool accidentally.
d.Store idle power tools out of
the reach of children and do not
allow persons unfamiliar with the
power tool or these instructions
to operate the power tool. Power
tools are dangerous in the hands of
untrained users.
2. CAUTION: Avoid accidental injury.
Keep hands and fingers safely away
from the oscillating Angled Scraper
(4), Blades (501, 503), and Sanding
Pad (502) when operating the Tool.
3. Avoid unintentional starting. Prepare
to begin work before turning on the
power tool.
e.Maintain power tools. Check
for misalignment or binding of
moving parts, breakage of parts
and any other condition that may
affect the power tool’s operation.
If damaged, have the power
tool repaired before use. Many
accidents are caused by poorly
maintained power tools.
4. Do not lay the power tool down until
it has come to a complete stop.
Moving parts can grab the surface
and pull the tool out of your control.
5. When using a handheld power tool,
maintain a firm grip on the tool with
both hands to resist starting torque.
f. Keep cutting accessories sharp
and clean. Properly maintained
cutting accessories with sharp cutting
edges are less likely to bind and are
easier to control.
6. Do not leave the power tool
unattended when it is plugged into
an electrical outlet. Turn off the tool,
and unplug it from its electrical outlet
before leaving.
g.Use the power tool and its
accessories in accordance with
these instructions, taking into
account the working conditions
and the work to be performed.
Use of the power tool for operations
different from those intended could
result in a hazardous situation.
7. This product is not a toy. Keep it out
of reach of children.
8. People with pacemakers should
consult their physician(s) before
use. Electromagnetic fields in close
proximity to heart pacemaker could
cause pacemaker interference or
pacemaker failure. In addition,
people with pacemakers should:
• Avoid operating alone.
5. Service
a.have your power tool serviced by
a qualified repair person using
SKU 67256
For technical questions, please call 1-800-444-3353.
Page 4
Download from Www.Somanuals.com. All Manuals Search And Download.
• Do not use with power switch locked
on.
• Properly maintain and inspect to
avoid electrical shock.
• Any power cord must be properly
grounded. Ground Fault Circuit
Interrupter (GFCI) should also be
implemented – it prevents sustained
electrical shock.
cover all possible conditions and
situations that may occur. It must
be understood by the operator that
common sense and caution are
factors which cannot be built into this
product, but must be supplied by the
operator.
Vibration Safety
9. Some dust created by power
sanding, sawing, grinding, drilling,
and other construction activities,
contains chemicals known [to the
State of California] to cause cancer,
birth defects or other reproductive
harm. Some examples of these
chemicals are:
This power tool vibrates during use.
Repeated or long-term exposure to
vibration may cause temporary or
permanent physical injury, particularly
to the hands, arms and shoulders. To
reduce the risk of vibration-related
injury:
1. Anyone using vibrating power tools
regularly or for an extended period
should first be examined by a doctor
and then have regular medical check-
ups to ensure medical problems are
not being caused or worsened from
use. Pregnant women or people
who have impaired blood circulation
to the hand, past hand injuries,
• Lead from lead-based paints
• Crystalline silica from bricks and
cement or other masonry products
• Arsenic and chromium from
chemically treated lumber
Your risk from these exposures
varies, depending on how often you
do this type of work. To reduce your
exposure to these chemicals: work in
a well ventilated area, and work with
approved safety equipment, such as
those dust masks that are specially
designed to filter out microscopic
particles. (California Health & Safety
Code § 25249.5, et seq.)
nervous system disorders, diabetes,
or Raynaud’s Disease should not
use this tool. If you feel any medical
or physical symptoms related to
vibration (such as tingling, numbness,
and white or blue fingers), seek
medical advice as soon as possible.
10. Handling the Power Cord on this
product will expose you to lead,
a chemical known to the State of
California to cause cancer, and
birth defects or other reproductive
harm. Wash hands after handling.
(California Health & Safety Code §
25249.5, et seq.)
2. Do not smoke during use. Nicotine
reduces the blood supply to the
hands and fingers, increasing the risk
of vibration-related injury.
3. Wear suitable gloves to reduce the
vibration effects on the user.
4. Use power tools with the lowest
vibration when there is a choice
between different processes.
11. The warnings, precautions,
and instructions discussed in
this instruction manual cannot
SKU 67256
For technical questions, please call 1-800-444-3353.
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Include vibration-free periods each
double Insulated Tools: Tools
with Two Prong Plugs
day of work.
6. Grip the power tool as lightly as
possible (while still keeping safe
control of it). Let the tool do the work.
7. To reduce vibration, maintain the
power tool as explained in this
manual. If any abnormal vibration
occurs, stop use immediately.
SaVE ThESE
1. Tools marked “Double Insulated”
do not require grounding. They
have a special double insulation
system which satisfies OSHA
requirements and complies with the
applicable standards of Underwriters
Laboratories, Inc., the Canadian
Standard Association, and the
National Electrical Code.
INSTRUCTIONS.
gROUNdINg
TO PREVENT
ELECTRIC ShOCK
aNd dEaTh FROM
INCORRECT gROUNdINg
WIRE CONNECTION:
Check with a qualified
(See Outlets for 2-Prong Plug.)
electrician if you are in doubt
as to whether the outlet is
properly grounded. do not
modify the Power Cord Plug
provided with the tool. Never
remove the grounding prong
from the Plug. do not use the
tool if the Power Cord or Plug
is damaged. If damaged, have
it repaired by a service facility
before use. If the Plug will not
fit the outlet, have a proper
outlet installed by a qualified
electrician.
2. Double insulated tools may be used
in either of the 120 volt outlets shown
in the preceding illustration.
(See Outlets for 2-Prong Plug.)
Extension Cords
1. Grounded tools require a three wire
extension cord. Double Insulated
tools can use either a two or three
wire extension cord.
2. As the distance from the supply
outlet increases, you must use a
heavier gauge extension cord. Using
extension cords with inadequately
sized wire causes a serious drop in
voltage, resulting in loss of power and
possible tool damage.
(See Table a, next page.)
SKU 67256
For technical questions, please call 1-800-444-3353.
Page 6
Download from Www.Somanuals.com. All Manuals Search And Download.
3. The smaller the gauge number of the
wire, the greater the capacity of the
cord. For example, a 14 gauge cord
can carry a higher current than a 16
gauge cord. (See Table a.)
Symbology
Double Insulated
Canadian Standards Association
Underwriters Laboratories, Inc.
Volts Alternating Current
Amperes
4. When using more than one extension
cord to make up the total length,
make sure each cord contains at
least the minimum wire size required.
(See Table a.)
V~
a
No Load Revolutions per Minute
(RPM)
5. If you are using one extension cord
for more than one tool, add the
nameplate amperes and use the sum
to determine the required minimum
cord size. (See Table a.)
n xxxx/min.
0
SPECIFICaTIONS
Electrical Input
Motor No Load Speed
120 V~ / 60 Hz / 1.6 A
19,000 OPM
6. If you are using an extension cord
outdoors, make sure it is marked with
the suffix “W-A” (“W” in Canada) to
indicate it is acceptable for outdoor
use.
Sanding Pad Dimensions 3” Triangle
Sanding Pad (Qty 1)
Sanding Sheet (Qty 2)
Angled Cutter Blade
(Qty 1)
Angled Scraper (Qty 1)
Half Moon Cutter Blade
(Qty 1)
Accessories
7. Make sure the extension cord is
properly wired and in good electrical
condition. Always replace a damaged
extension cord or have it repaired by
a qualified electrician before using it.
UNPaCKINg
When unpacking, check to make sure
that the item is intact and undamaged. If
any parts are missing or broken, please
call Harbor Freight Tools at
8. Protect the extension cords from
sharp objects, excessive heat, and
damp or wet areas.
1-800-444-3353 as soon as possible.
RECOMMENdEd MINIMUM WIRE
gaUgE FOR EXTENSION CORdS*
(120/240 VOLT)
EXTENSION CORd
NaMEPLaTE
LENgTh
aMPERES
(at full load)
0 – 2.0
2.1 – 3.4
3.5 – 5.0
5.1 – 7.0
7.1 – 12.0
18
18
18
18
18
18
18
18
16
14
18
18
16
14
12
18
16
14
12
10
16
14
12
12
-
* based on limiting the line
voltage drop to five volts at
150% of the rated amperes.
TabLE a
REV 09f, 10b, 10e
SKU 67256
For technical questions, please call 1-800-444-3353.
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
refer to the Assembly Diagram near
the end of this manual.
COMPONENTS
Power Switch (44)
1. Turn the Power Switch off and unplug
the tool.
OFF
ON
Spindle (5)
Tool
attachment
[angled
Figure b
Angled Scraper (4)
Sanding
Pad
Scraper (4)]
(502)
Spindle
(5)
Angled Cutter
Blade (501)
Half Moon Cutter Blade (503)
Sanding
Sheets (504)
Cap Screw (1)
Small Washer (2)
Large Washer (3)
Hex Wrench (505)
2. Place the attachment over the
Spindle (5), shoulder facing away
from the tool. Line up the holes on
the attachment with the pins on the
Spindle shoulder.
(not shown):
Two replacement
Carbon Brushes (40)
Figure a
(See Figure b.)
aSSEMbLY INSTRUCTIONS
Read the ENTIRE IMPORTaNT
SaFETY INFORMaTION
section at the beginning of this
manual including all text under
subheadings therein before set
up or use of this product.
TO PREVENT
SERIOUS INjURY
FROM aCCIdENTaL
OPERaTION:
Figure C
Turn the Power Switch (44) off
and unplug the tool from its
electrical outlet before
assembly.
Note: For additional information regarding
Attachments (with the exception of
the long Angled Cutter Blades) may
the parts listed in the following pages,
REV 10e
SKU 67256
For technical questions, please call 1-800-444-3353.
Page 8
Download from Www.Somanuals.com. All Manuals Search And Download.
be mounted at angles up to 90° left or
right.
Torque to 10 ft-lbs
Angled Cutter Blade (501)
Figure d
Note: The long Angled Cutter Blade (501)
should only be used in the straight
ahead position. (See Figure d.)
Figure F
4. Tighten the cap screw onto the
Spindle using the provided hex key.
Torque firmly (approximately 10
ft-lbs). After securing, the attachment
should not move on the spindle. If it
can move with the power off, remount
it, making sure that the holes on the
attachment line up with the pins on
the spindle. Tighten the cap screw
securely.
Place Large
Washer,
cupped side
down
Figure E
3. Slide the Small Washer (2), then the
Large Washer (3) onto the the Cap
Screw (1). Make sure the cupped
side of the Large Washer is toward
the tool. While holding the attachment
over the pins on the tool, thread the
Cap Screw in place. (See Figure E.)
REV 10e
SKU 67256
For technical questions, please call 1-800-444-3353.
Page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Avoid contact with foreign objects
such as metal screws and nails when
sanding, scraping, or cutting.
OPERaTINg INSTRUCTIONS
Read the ENTIRE IMPORTaNT
SaFETY INFORMaTION
section at the beginning of this
manual including all text under
subheadings therein before set
up or use of this product.
6. Do not apply excessive pressure
on the tool. Allow the tool to do the
work.
7. When finished, turn off the tool and
allow it to completely stop before
setting it down. Then unplug the tool
from its electrical outlet.
Work Piece and Work area Set Up
1. Designate a work area that is clean
and well-lit. The work area must not
allow access by children or pets to
prevent injury and distraction.
8. To replace the Sanding Sheet, simply
pull it off the pad and press a new
sheet in place.
2. Route the Power Cord (46) along a
safe route to reach the work area
without creating a tripping hazard or
exposing the Power Cord to possible
damage. The Power Cord must
reach the work area with enough
extra length to allow free movement
while working.
9. Prior to storing the tool, remove the
attachment and wipe it clean. Store
the Tool in a clean, dry, safe location
out of reach of children and other
unauthorized persons.
3. Secure loose work pieces using
a vise or clamps (not included) to
prevent movement while working.
general Operating Instructions
1. With the tool unplugged, mount the
desired attachment in place.
2. Pull the Power Switch (44) back to
its off position. Then plug the Power
Cord (46) into the nearest 120 volt,
grounded electrical outlet.
3. To turn on the tool, slide the Power
Switch (44) forward.
4. Do not allow contact between
the Sanding Sheet (504), Angled
Scraper (4), or Blade (501, 503) and
workpiece until the tool is running at
full speed.
REV 10e
SKU 67256
For technical questions, please call 1-800-444-3353.
Page 10
Download from Www.Somanuals.com. All Manuals Search And Download.
3. If you notice decreased performance,
have the unit serviced and Carbon
Brushes (40) replaced by a qualified
technician.
MaINTENaNCE aNd
SERVICINg
Procedures not specifically
explained in this manual
must be performed only by a
qualified technician.
4.
WaRNINg! If the Power Cord
(46) of this Tool is damaged,
it must be replaced only by a
qualified service technician.
TO PREVENT
SERIOUS INjURY
FROM aCCIdENTaL
OPERaTION:
PLEaSE REad ThE
FOLLOWINg CaREFULLY
Turn the Power Switch (44) of
the Tool to its “OFF” position
and unplug the tool from its
electrical outlet before
performing any inspection,
maintenance, or cleaning
procedures.
THE MANUFACTURER AND/OR
DISTRIBUTOR HAS PROVIDED THE
PARTS LIST AND ASSEMBLy DIAgRAM IN
THIS MANUAL AS A REfERENCE TOOL
ONLy. NEITHER THE MANUfACTURER
OR DISTRIBUTOR MAKES ANY
REPRESENTATION OR WARRANTY OF
ANY KIND TO THE BUYER THAT HE
OR SHE IS qUALIfIED TO MAKE ANy
REPAIRS TO THE PRODUCT, OR THAT HE
OR SHE IS qUALIfIED TO REPLACE ANy
PARTS OF THE PRODUCT. IN FACT, THE
MANUFACTURER AND/OR DISTRIBUTOR
ExPRESSLy STATES THAT ALL REPAIRS
AND PARTS REPLACEMENTS SHOULD
BE UNDERTAKEN BY CERTIFIED AND
LICENSED TECHNICIANS, AND NOT By
THE BUyER. THE BUyER ASSUMES ALL
RISK AND LIABILITy ARISINg OUT Of
HIS OR HER REPAIRS TO THE ORIgINAL
PRODUCT OR REPLACEMENT PARTS
THERETO, OR ARISING OUT OF HIS OR
HER INSTALLATION Of REPLACEMENT
PARTS THERETO.
TO PREVENT SERIOUS
INjURY FROM TOOL
FaILURE:
do not use damaged
equipment. If abnormal noise
or vibration occurs, have the
problem corrected before
further use.
1. BEFORE EACH USE, inspect the
general condition of the Tool. Check
for loose screws, misalignment or
binding of moving parts, cracked or
broken parts, damaged electrical
wiring, and any other condition that
may affect its safe operation.
The Sanding Sheet (504) should not
be dull or contain excessive debris
build-up.
The Angled Scraper (4) and cutting
Blades (501, 503) should be clean
and sharp.
2. AFTER USE, clean external surfaces
of the tool with clean cloth.
SKU 67256
For technical questions, please call 1-800-444-3353.
Page 11
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Problem
Tool will not start.
Possible Causes
1. Cord not connected.
Likely Solutions
1. Check that cord is plugged in.
2. No power at outlet.
2. Check power at outlet. If outlet is unpowered,
turn off tool and check circuit breaker. If
breaker is tripped, make sure circuit is right
capacity for tool and circuit has no other
loads.
3. Internal damage or wear.
(Carbon brushes or switch,
for example.)
3. Have technician service tool.
Attachment is loose 1. Holes on attachment not
on the tool. lined up with pins on Spindle.
1. Remove the attachment and re-mount,
making sure that the holes in the attachment
are secured over the pins on the Spindle.
2. Cap screw not tight enough. 2. Remove the attachment and re-mount,
making sure that the holes in the attachment
are secured over the pins on the Spindle,
then tighten the Cap Screw to at least 10
ft-lbs.
Tool operates slowly. Extension cord too long or wire Eliminate use of extension cord. If an extension
size too small.
cord is needed, use shorter/heavier gauge cord.
See Extension Cords in GROUNDING section.
Performance
decreases over time.
1. Attachment dull or damaged. 1. Keep cutting accessories sharp. Replace as
needed.
2. Carbon brushes worn or
damaged.
2. Have qualified technician replace brushes.
Excessive noise or Internal damage or wear.
Have technician service tool.
rattling.
(Carbon brushes or bearings,
for example.)
Overheating.
1. Forcing tool to work too fast. 1. Allow tool to work at its own rate.
2. Attachment dull or damaged. 2. Keep cutting accessories sharp. Replace as
needed.
3. Blocked motor housing
vents.
3. Wear ANSI-approved safety goggles and
NIOSH-approved dust mask/respirator while
blowing dust out of motor using compressed
air.
4. Motor being strained by long 4. Eliminate use of extension cord. If an
or small diameter extension
cord.
extension cord is needed, use one with the
proper diameter for its length and load. See
Extension Cords in GROUNDING section.
Follow all safety precautions whenever diagnosing or servicing the
tool. disconnect power supply before service.
REV 10e
SKU 67256
For technical questions, please call 1-800-444-3353.
Page 12
Download from Www.Somanuals.com. All Manuals Search And Download.
PaRTS LIST aNd aSSEMbLY dIagRaM
Part
1
2
3
4
5
6
7
8
description
Cap Screw (M8 x 1.25 x 12)
Small Washer
Qty
Part
27
29
31
32
33
34
36
37
38
39
40
41
42
43
44
45
46
47
48
49
description
Qty
1
1
1
1
2
1
2
2
2
2
2
1
1
2
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
4
4
1
1
1
Stator
Plastic Housing
Link Pole
Cord Clip
Screw (ST4.0 x 14)
Pull Brace
Lug
Brush Holder
Spring
Screw (ST4.0 x 20)
Carbon Brush
Screw (ST4.0 x 10)
Back Housing
Screw (ST4.0 x 16)
Power Switch
Cord Guard
Power Cord
Cap
Large Washer
Angled Scraper
Spindle
Rubber Casing
Circlip for Shaft 26
Spline Spring Washer
Bearing (6000)
Block
Bronze Bushing
Screw (ST4 x 27)
Plain Washer (#4)
Reducer
Circlip for Shaft 5
Bearing (60025)
Sealing Washer
Middle Cover
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
1
1
1
1
Bearing (608)
Balance Block
Switch Holder
Terminal
Armature
1
1
501 Angled Cutter Blade
502 Sanding Pad
Bearing (6017)
Rubber Bushing
Wind Guide Circle
Screw (ST4.0 x 50)
Plain Washer (#4)
1
1
2
2
503 Half Moon Cutter Blade
504 Sanding Sheets
505 Hex Wrench
1
503 - Half Moon Cutter Blade (not shown)
504 - Sanding Sheets (not shown)
505 - Hex Wrench (not shown)
REV 10e, 10k
SKU 67256
For technical questions, please call 1-800-444-3353.
Page 13
Download from Www.Somanuals.com. All Manuals Search And Download.
Record Product’s Serial Number
here:
either repair or replace the product at our
election or we may elect to refund the
purchase price if we cannot readily and
quickly provide you with a replacement. We
will return repaired products at our expense,
but if we determine there is no defect, or that
the defect resulted from causes not within
the scope of our warranty, then you must
bear the cost of returning the product.
Note: If product has no serial number,
record month and year of purchase
instead.
Note: Some parts are listed and shown for
illustration purposes only, and are not
available individually as replacement
parts.
This warranty gives you specific legal
rights and you may also have other rights
which vary from state to state.
LIMITEd 90 daY WaRRaNTY
Harbor Freight Tools Co. makes every
effort to assure that its products meet
high quality and durability standards, and
warrants to the original purchaser that this
product is free from defects in materials
and workmanship for the period of 90 days
from the date of purchase. This warranty
does not apply to damage due directly or
indirectly, to misuse, abuse, negligence
or accidents, repairs or alterations outside
our facilities, criminal activity, improper
installation, normal wear and tear, or to
lack of maintenance. We shall in no event
be liable for death, injuries to persons
or property, or for incidental, contingent,
special or consequential damages arising
from the use of our product. Some states
do not allow the exclusion or limitation of
incidental or consequential damages, so the
above limitation of exclusion may not apply
to you. THIS WARRANTy IS ExPRESSLy
IN LIEU Of ALL OTHER WARRANTIES,
ExPRESS OR IMPLIED, INCLUDINg THE
WARRANTIES Of MERCHANTABILITy
AND FITNESS.
3491 Mission Oaks Blvd. • PO Box
6009 • Camarillo, CA 93011 • (800)
444-3353
To take advantage of this warranty,
the product or part must be returned to us
with transportation charges prepaid. Proof
of purchase date and an explanation of the
complaintmustaccompanythemerchandise.
If our inspection verifies the defect, we will
SKU 67256
For technical questions, please call 1-800-444-3353.
Page 14
Download from Www.Somanuals.com. All Manuals Search And Download.
|