7-1/4” METAL CUTTING SAW
94362
ASSEMBLY AND OPERATING INSTRUCTIONS
Due to continuing improvements, actual product may differ slightly from the product described herein.
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
Copyright © 2006 by Harbor Freight Tools®. All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions, please call 1-800-444-3353.
Download from Www.Somanuals.com. All Manuals Search And Download.
2.
3.
Do not operate power tools in explosive atmospheres, such as in the
presence of flammable liquids, gases, or dust. Power tools create sparks
which may ignite the dust or fumes.
Keep bystanders, children, and visitors away while operating a power tool.
Distractions can cause you to lose control. Protect others in the work area from
debris such as chips and sparks. Provide barriers or shields as needed.
ELECTRICAL SAFETY
4.
Grounded tools must be plugged into an outlet properly installed and
grounded in accordance with all codes and ordinances. Never remove the
grounding prong or modify the plug in any way. Do not use any adapter
plugs. Check with a qualified electrician if you are in doubt as to whether
the outlet is properly grounded. If the tools should electrically malfunction or
break down, grounding provides a low resistance path to carry electricity away
from the user.
5.
6.
Double insulated tools are equipped with a polarized plug (one blade is
wider than the other). This plug will fit in a polarized outlet only one way. If
the plug does not fit fully in the outlet, reverse the plug. If it still does not
fit, contact a qualified electrician to install a polarized outlet. Do not
change the plug in any way. Double insulation
eliminates the need for the
three wire grounded power cord and grounded power supply system.
Avoid body contact with grounded surfaces such as pipes, radiators,
ranges, and refrigerators. There is an increased risk of electric shock if your
body is grounded.
7.
8.
Do not expose power tools to rain or wet conditions. Water entering a power
tool will increase the risk of electric shock.
Do not abuse the Power Cord. Never use the Power Cord to carry the tools
or pull the Plug from an outlet. Keep the Power Cord away from heat, oil,
sharp edges, or moving parts. Replace damaged Power Cords immediately.
Damaged Power Cords increase the risk of electric shock.
9.
When operating a power tool outside, use an outdoor extension cord
marked “W-A” or “W”. These extension cords are rated for outdoor use, and
reduce the risk of electric shock.
PERSONAL SAFETY
10.
Stay alert. Watch what you are doing, and use common sense when
operating a power tool. Do not use a power tool while tired or under the
influence of drugs, alcohol, or medication. A moment of inattention while
operating power tools may result in serious personal injury.
SKU 94362
For technical questions, please call 1-800-444-3353.
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
11.
12.
13.
14.
15.
Dress properly. Do not wear loose clothing or jewelry. Contain long hair.
Keep your hair, clothing, and gloves away from moving parts. Loose
clothes, jewelry, or long hair can be caught in moving parts.
Avoid accidental starting. Be sure the Power Switch is off before plugging
in. Carrying power tools with your finger on the Power Switch, or plugging in
power tools with the Power Switch on, invites accidents.
Remove adjusting keys or wrenches before turning the power tool on. A
wrench or a key that is left attached to a rotating part of the power tool may result
in personal injury.
Do not overreach. Keep proper footing and balance at all times. Proper
footing and balance enables better control of the power tool in unexpected
situations.
Use safety equipment. Always wear eye protection. Dust mask, nonskid
safety shoes, hard hat, or hearing protection must be used for appropriate
conditions.
TOOL USE AND CARE
16.
Use clamps (not included) or other practical ways to secure and support
the workpiece to a stable platform. Holding the work by hand or against your
body is unstable and may lead to loss of control.
17.
18.
Do not force the tool. Use the correct tool for your application. The correct
tool will do the job better and safer at the rate for which it is designed.
Do not use the power tool if the Power Switch does not turn it on or off.
Any tool that cannot be controlled with the Power Switch is dangerous and must
be replaced.
19.
Disconnect the Power Cord Plug from the power source before making any
adjustments, changing accessories, or storing the tool. Such preventive
safety measures reduce the risk of starting the tool accidentally.
20.
21.
Store idle tools out of reach of children and other untrained persons. Tools
are dangerous in the hands of untrained users.
Maintain tools with care. Keep cutting tools sharp and clean. Properly
maintained tools with a sharp cutting edge are less likely to bind and are easier
to control. Do not use a damaged tool. Tag damaged tools “Do not use” until
repaired.
SKU 94362
For technical questions, please call 1-800-444-3353.
Page 4
Download from Www.Somanuals.com. All Manuals Search And Download.
22.
23.
Check for misalignment or binding of moving parts, breakage of parts, and
any other condition that may affect the tool’s operation. If damaged, have
the tool serviced before using. Many accidents are caused by poorly
maintained tools.
Use only accessories that are recommended by the manufacturer for your
model. Accessories that may be suitable for one tool may become hazardous
when used on another tool.
SERVICE
24.
25.
Tool service must be performed only by qualified repair personnel. Service
or maintenance performed by unqualified personnel could result in a risk of injury.
When servicing a tool, use only identical replacement parts. Follow
instructions in the “Inspection, Maintenance, And Cleaning” section of this
manual. Use of unauthorized parts or failure to follow maintenance instructions
may create a risk of electric shock or injury.
GROUNDING
WARNING!
Improperly connecting the grounding wire can result in the risk of electric
shock. Check with a qualified electrician if you are in doubt as to whether the
outlet is properly grounded. Do not modify the power cord plug provided with
the tool. Never remove the grounding prong from the plug. Do not use the
tool if the power cord or plug is damaged. If damaged, have it repaired by
a service facility before use. If the plug will not fit the outlet, have a proper
outlet installed by a qualified electrician.
GROUNDED TOOLS: TOOLS WITH THREE PRONG PLUGS
1.
2.
Tools marked with “Grounding Required” have a three wire cord and three prong
grounding plug. The plug must be connected to a properly grounded outlet. If
the tool should electrically malfunction or break down, grounding provides a low
resistance path to carry electricity away from the user, reducing the risk of electric
shock. (See Figure A, next page.)
The grounding prong in the plug is connected through the green wire inside the
cord to the grounding system in the tool. The green wire in the cord must be the
only wire connected to the tool’s grounding system and must never be attached
to an electrically “live” terminal. (See Figure A.)
SKU 94362
For technical questions, please call 1-800-444-3353.
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
3.
Your tool must be plugged into an appropriate outlet, properly installed and
grounded in accordance with all codes and ordinances. The plug and outlet
should look like those in the following illustration. (See Figure A.)
FIGURE A
DOUBLE INSULATED TOOLS: TOOLS WITH TWO PRONG PLUGS
4.
5.
Tools marked “Double Insulated” do not require grounding. They have a special
double insulation system which satisfies OSHA requirements and complies with
the applicable standards of Underwriters Laboratories, Inc., the Canadian
Standard Association, and the National Electrical Code. (See Figure B.)
Double insulated tools may be used in either of the 120 volt outlets shown in the
following illustration. (See Figure B.)
FIGURE B
SKU 94362
For technical questions, please call 1-800-444-3353.
Page 6
Download from Www.Somanuals.com. All Manuals Search And Download.
EXTENSION CORDS
1.
2.
Grounded tools require a three wire extension cord. Double Insulated tools
can use either a two or three wire extension cord.
As the distance from the supply outlet increases, you must use a heavier gauge
extension cord. Using extension cords with inadequately sized wire causes a
serious drop in voltage, resulting in loss of power and possible tool damage.
(See Figure C, and Figure D, next page.)
3.
4.
5.
The smaller the gauge number of the wire, the greater the capacity of the cord.
For example, a 14 gauge cord can carry a higher current than a 16 gauge cord.
(See Figure C, and Figure D.)
If using more than one extension cord to make up the total length, make sure
each cord contains at least the minimum wire size required.
(See Figure C, and Figure D.)
If you are using one extension cord for more than one tool, add the nameplate
amperes and use the sum to determine the required minimum cord size.
(See Figure C, and Figure D.)
6.
7.
If you are using an extension cord outdoors, make sure it is marked with the
suffix “W-A” (“W” in Canada) to indicate it is acceptable for outdoor use.
Make sure your extension cord is properly wired and in good electrical condition.
Always replace a damaged extension cord or have it repaired by a qualified
electrician before using it.
8.
Protect your extension cords from sharp objects, excessive heat, and damp or
wet areas.
RECOMMENDED MINIMUM WIRE GAUGE FOR EXTENSION CORDS*
(120 VOLT)
EXTENSION CORD LENGTH
NAMEPLATE
AMPERES
(At Full Load)
25
Feet
18
18
18
18
18
14
12
50
Feet
18
18
18
16
14
12
75
Feet
18
18
16
14
12
10
-
100
Feet
18
16
14
12
10
-
150
Feet
16
14
12
12
-
0 – 2.0
2.1 – 3.4
3.5 – 5.0
5.1 – 7.0
7.1 – 12.0
12.1 – 16.0
16.1 – 20.0
-
-
10
-
* Based on limiting the line voltage drop
to five volts at 150% of the rated amperes.
FIGURE C
SKU 94362
For technical questions, please call 1-800-444-3353.
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
SYMBOLOGY
Double Insulated
Canadian Standards
Association
Underwriters
Laboratories, Inc.
Volts Alternating Current
V ~
A
Amperes
No Load Revolutions
per Minute (RPM)
no
xxxx/min.
SPECIFIC SAFETY RULES
1.
2.
Maintain a safe working environment. Keep the work area well lit. Make sure
there is adequate surrounding workspace. Always keep the work area free of
obstructions, grease, oil, trash, and other debris. Do not use this product in
areas near flammable chemicals, dusts, and vapors.
Maintain labels and nameplates on the Saw. These carry important
information. If unreadable or missing, contact Harbor Freight Tools for a
replacement.
3.
4.
5.
6.
7.
8.
Use eye and hearing protection. Always wear ANSI-approved safety impact
eye goggles and hearing protectors when using this product.
Make sure to read and understand all instructions and safety precautions
as outlined in the manufacturer’s manual.
When using a handheld power tool, always maintain a firm grip on the tool
with both hands (at all times) to resist starting torque.
Always keep the Power Cord (71) away from moving parts of the Saw. Keep
the Power Cord away from the direction of the cut.
Avoid unintentional starting. Make sure you are prepared to begin work before
turning on the Saw.
Keep hands and fingers away from the Saw Blade (10) at all times. If both
hands are holding the Saw by its Handles (64, 65, 72), they cannot be cut by the
Saw Blade.
SKU 94362
For technical questions, please call 1-800-444-3353.
Page 8
Download from Www.Somanuals.com. All Manuals Search And Download.
9.
Do not reach underneath the workpiece. The Blade Cover (12) can not protect
you from the Saw Blade (10) below the workpiece.
10.
Never hold the workpiece being cut in your hands or across your legs. It is
important to support the workpiece properly with clamps or other appropriate
devices to minimize body exposure, blade binding, or loss of control.
11.
12.
Keep your body positioned to either side of the Saw Blade (10), but not in
line with the Saw Blade. Kickback could cause the Saw to jump backwards.
Causes and operator prevention of “kickback”: Kickback is a sudden reaction
to a pinched, bound, or misaligned Saw Blade (10), causing an uncontrolled
Saw to lift up and out of the workpiece toward the operator. When the Saw Blade
is pinched or bound tightly by the kerf closing down, the Saw Blade stalls and the
motor reaction drives the tool rapidly back toward the operator. If the Saw Blade
becomes twisted or misaligned in the cut, the teeth at the back edge of the Saw
Blade can dig into the top surface of the workpiece causing the Saw Blade to
climb out of the kerf and jump back toward the operator. Kickback is a result of
tool misuse and/or incorrect operating procedures or conditions and can be
avoided by taking proper precautions as given below:
A. Maintain a firm grip with both hands on the Saw, and position your body
and arm to allow you to resist kickback forces. Kickback forces can be
controlled by the operator if proper precautions are taken.
B. When the Saw Blade (10) is binding, or when interrupting a cut for any
reason, release theTrigger Switch (66) and hold the Saw motionless in
the workpiece until the Saw Blade comes to a complete stop. Never
attempt to remove the Saw from the workpiece or pull the Saw backward while
the Saw Blade is in motion or kickback may occur. Investigate and take cor-
rective actions to eliminate the cause of Saw Blade binding.
C. When restarting a Saw in the workpiece, center the Saw Blade (10) in the
kerf and check that the saw teeth are not engaged into the workpiece. If
the Saw Blade is binding, it may walk up or kickback from the workpiece as
the Saw is restarted.
D. Support large panels to minimize the risk of Saw Blade pinching and
kickback. Large panels tend to sag under their own weight. Supports must
be placed under the panel on both sides, near the line of cut and near the
edge of the panel.
E. Do not use a dull or damaged Saw Blade (10). Unsharpened or improperly
set Saw Blades produce a narrow kerf causing excessive friction, Saw Blade
binding and kickback.
SKU 94362
For technical questions, please call 1-800-444-3353.
Page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
F. The Saw Blade (10) depth adjusting Lock Lever (50) and Rip Guide Pins
(29) must be kept tight and secure before making a cut. If Saw Blade
adjustments shift while cutting, it may cause binding and kickback.
13.
Check the Blade Cover (12) for proper closing before each use. Do not
operate the Saw if the Blade Cover does not move freely and close instantly.
Never clamp or tie the Blade Cover into the open position. If theSaw is
accidently dropped, the Blade Cover may be bent. Raise the Blade Cover and
make sure it moves freely and does not touch the Saw Blade (10) or any other
part, in all angles and depths of cut.
14.
15.
Check the operation and condition of the Blade Cover Spring (13). If the
Blade Cover and the Spring are not operating properly, they must be
serviced before use. The Blade Cover may operate sluggishly due to damaged
parts, gummy deposits, or a buildup of debris.
The Blade Cover (12) should be retracted manually only for special cuts
such as “pocket cuts” and “compound cuts”. Raise the Blade Cover by it
retracting handle. As soon as the Saw Blade (10) enters the workpiece, the
Blade Cover must be released. For all other sawing, the Blade Cover should
operate automatically.
16.
17.
Always observe that the Blade Cover (12) is covering the Saw Blade (10)
before placing the Saw down on a bench or floor. An unprotected, rotating
Saw Blade will cause the Saw to walk backward, cutting whatever is in its path.
Be aware of the time it takes for the Saw Blade to stop after the Trigger Switch
(66) is released.
Always hold the Saw by its insulated gripping surfaces when performing an
operation where the cutting tool may accidentally contact wiring or its own
Power Cord (71). Contact with a “live” wire will also make exposed metal parts of
the tool “live” and shock the operator.
18.
19.
When ripping, always use the Rip Guide (73). This improves the accuracy of
the cut, and reduces the chance for Saw Blade (10) binding.
Always use the proper size and type of Saw Blade (10): 7-1/4”diameter,
metal cutting, 3,500 minimum rated RPM or greater.
REV 04/06
SKU 94362
For technical questions, please call 1-800-444-3353.
Page 10
Download from Www.Somanuals.com. All Manuals Search And Download.
20.
21.
Always use Saw Blades with the correct size and shape (diamond
vs. round) arbor holes. Saw Blades that do not match the mounting hardware
of the Saw will run eccentrically, causing loss of control.
Never use damaged or incorrect Saw Blade (part #10) Inner/Outer Flanges
(9, 11) or Screw (15). The Inner and Outer Flanges and Screw were specially
designed for this Saw, for optimum performance and safety ofoperation.
22.
Feed the Saw gradually into the workpiece. Do not attempt to force the Saw
to remove material faster than it was designed to cut.
23.
24.
25.
Secure the workpiece. Whenever possible, secure the workpiece with a vise or
clamps (not included).
Make sure to remove all adjusting wrenches and tools before turning on
the Saw.
Do not force the Saw. This tool will do the work better and safer at the speed
and capacity for which it was designed.
26.
27.
Never leave the Saw unattended when it is plugged into an electrical
outlet. Turn off the tool, and unplug it from its electrical outlet before leaving.
Reduce the risk of accidental starting. Make sure the Trigger Switch (66) is in
the “OFF” position before plugging the Power Cord (71) into a 120 volt, grounded,
electrical outlet.
28.
29.
Do not allow children to use or play with this product.
Store idle equipment. When not in use, tools and equipment should be stored
in a dry location to inhibit rust. Always lock up tools and equipment, and keep out
of reach of children.
30.
31.
Do not use this product if under the influence of alcohol or drugs. Read
warning labels on prescriptions to determine if your judgement or reflexes are
impaired while taking drugs. If there is any doubt, do not attempt to use this
product.
Dress properly. Do not wear loose clothing or jewelry as they can be caught in
moving parts. Wear restrictive hair covering to contain long hair.
32.
33.
Do not overreach. Keep proper footing and balance at all times. Do not reach
over or across running machines.
Industrial applications must follow OSHA requirements.
SKU 94362
For technical questions, please call 1-800-444-3353.
Page 11
Download from Www.Somanuals.com. All Manuals Search And Download.
34.
35.
36.
Maintain this product with care. Keep this product clean for better and safer
performance.
Maintenance: For your safety, service and maintenance should be performed
regularly by a qualified technician.
Check for damaged parts. Before using this product, carefully check that it will
operate properly and perform its intended function. Check for damaged parts
and any other conditions that may affect the operation of this product. Replace
or repair damaged or worn parts immediately.
37.
38.
Replacement parts and accessories: When servicing, use only identical
replacement parts. Only use accessories intended for use with this product.
Use the right tool or attachment for the job. Do not attempt to force a small
tool or attachment to do the work of a larger industrial tool or attachment.
There are certain applications for which this product was designed. It will do the
job better and more safely at the rate for which it was intended. Do not modify
this product, and do not use this product for a purpose for which it was not
intended.
39.
40.
Always turn off the Saw, and unplug it from its electrical outlet before
performing any inspection or maintenance procedures.
WARNING!
Sparking Hazard. Some metal cutting will create sparks. Do not
cut near flammable materials, liquid or vapor. Always wear ANSI-approved eye
protection.
41.
WARNING! Some dust created by power sanding, sawing, grinding, drilling, and
other construction activities, contain chemicals known (to the State of California) to
cause cancer, birth defects or other reproductive harm. Some examples of these
chemicals are: lead from lead-based paints, crystalline silica from bricks and cement or
other masonry products, arsenic and chromium from chemically treated lumber. Your risk
from these exposures varies, depending on how often you do this type of work. To
reduce your exposure to these chemicals: work in a well ventilated area, and work with
approved safety equipment, such as those dust masks that are specially designed to
filter out microscopic particles. (California Health & Safety Code § 25249.5, et seq.)
42.
WARNING! People with pacemakers should consult their physician(s) before
using this product. Operation of electrical equipment in close proximity to a heart
pacemaker could cause interference or failure of the pacemaker.
UNPACKING
When unpacking, check to make sure all the parts shown on the Parts Lists on pages 20
and 21 are included. If any parts are missing or broken, please call Harbor Freight Tools
at the number shown on the cover of this manual as soon as possible.
SKU 94362
For technical questions, please call 1-800-444-3353.
Page 12
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY INSTRUCTIONS
NOTE: For additional information regarding the parts mentioned in the following pages,
refer to the Assembly Diagram on page 22.
To Attach The Rip Guide, And Adjust The Width Of A Cut:
1.
WARNING! Prior to performing this procedure, make sure the Trigger Switch
(66) of the Saw is in its’ “OFF” position and the Power Cord (71) is unplugged
from its electrical outlet.
2.
3.
Slightly loosen the two Pins (29). (See Figure D.)
Slide the arms of the Rip Guide (73) through the slots in the Base (24).
(See Figure D.)
4.
Featured on the arm of the Rip Guide (73) is a width scale, divided in increments
of 1/16”. To adjust the width of the cut, slide the arm of the Rip Guide to the right
or left until the desired width is acquired. Then, retighten the Pins (29) to hold the
Rip Guide in place. (See Figure D.)
TOP
VIEW
RIP GUIDE (#73)
BODY (#32)
BASE (#24)
PIN (#29)
PIN (#29)
SIDE HANDLE
(#72)
FIGURE D
To Attach The Side Handle:
To attach the Side Handle (72), simply screw the Side Handle into the threaded
mounting hole located in the upper/left Body (32) of the Saw. (See Figure D.)
SKU 94362
For technical questions, please call 1-800-444-3353.
Page 13
Download from Www.Somanuals.com. All Manuals Search And Download.
To Adjust The Depth Of Cut:
1.
WARNING! Prior to performing this procedure, make sure the Trigger Switch
(66) of the Saw is in its “OFF” position and the Power Cord (71) is unplugged
from its electrical outlet.
2.
3.
The Saw may be adjusted to cut to a maximum depth of 2-1/4”.
When adjusting the depth of cut, always make sure the teeth of the Saw Blade
(10) cut (or protrude) about 1/4” through the bottom surface of the workpiece.
4.
5.
To adjust the depth of cut, pull up on the Lock Lever (50) located at the rear of the
Saw. (See Figure E.)
Raise or lower the Base (24) until the desired cutting depth is acquired. Then,
push down on the Depth Control Lever (52) to lock the Base in place.
(See Figure E.)
Depth Control Lever (52)
BASE (24)
FIGURE E
To Install A Saw Blade:
1.
WARNING! Prior to performing this procedure, make sure the Trigger Switch
(66) of the Saw is in its “OFF” position and the Power Cord (71) is unplugged from
its electrical outlet.
2.
CAUTION! Always make sure the Saw Blade (10) installed is a 7-1/4”
diameter, metal cutting saw blade, with an RPM rating of 5,800 or greater.
SKU 94362
For technical questions, please call 1-800-444-3353.
Page 14
Download from Www.Somanuals.com. All Manuals Search And Download.
3.
4.
Turn the Knob (1) and remove the Plastic Cover (2). (See Figure F.)
Remove the three phillips Screws (33) located on the left side of the Body (32).
(See Figure G.)
KNOB (#1)
PLASTIC COVER (#2)
FIGURE F
SCREW (#33)
BODY (#32)
SCREW (#33)
SCREW
(#33)
FIGURE G
5.
Depress the Depth Control Lever (52) and lower the Base (24) so that the Inner
Cover (7) and be removed. (See Figure H.)
Depth Control
Lever (52) hidden
from view.
INNER COVER (#7)
Base (24)
FIGURE H
SKU 94362
For technical questions, please call 1-800-444-3353.
Page 15
Download from Www.Somanuals.com. All Manuals Search And Download.
6.
7.
Depress the Depth Control Lever (52) to hold the Saw Blade (10) in place. Use
the Blade Wrench (74) to unscrew and remove the Bolt (8). Release pressure on
the Blade Lock Lever. (See Figure I.)
Remove the Outer Flange (11). Then, raise and hold the Blade Cover (12) in its
“up” position while removing the Saw Blade. (See Figure I.)
DEPTH CONTROL LEVER (#52)
SAW BLADE (#10)
BOLT (#8)
OUTER
FLANGE
(#11)
BLADE COVER (#12)
SAW BLADE (#10)
ARROW POINTING
TO FRONT
BOLT (#8)
FIGURE I
OUTER FLANGE (#11)
8.
Raise and hold the Blade Cover (12) in its “up” position while installing the
new Saw Blade (10). IMPORTANT: When installing the new Saw Blade, make
sure the arrow on the Saw Blade points to the front of the Saw.
(See Figure I.)
9.
Replace the Outer Flange (11) and, while depressing the Depth Control Lever
(52), use the Blade Wrench (74) to firmly tighten the Bolt (8) in place.
(See Figure I.)
10.
11.
Replace the Inner Cover (7). Then replace the Plastic Cover (2), making sure to
turn the Knob (1) to lock the Plastic Cover in place.
(See Figures G, and H.)
Replace the three phillips Screws (33) on the left side of the Body (32).
(See Figure F.)
SKU 94362
For technical questions, please call 1-800-444-3353.
Page 16
Download from Www.Somanuals.com. All Manuals Search And Download.
Proper Operation During The Cutting Process:
WARNING! Never pass hands and fingers directly in front of, to the rear, or
below,the Saw Blade (10) when cutting a workpiece. Always push the Saw
into the workpiece with both hands firmly gripping the Handles (64, 65, 72).
1.
Make all necessary adjustments to the Saw (width and depth) as previously
discussed in this manual.
2.
3.
Make sure the workpiece is free from screws, rivets, and any other foreign objects
which could damage the Saw Blade (10).
Make sure the workpiece is supported at all times. Whenever possible, secure
the workpiece in a vise or with clamps (not included). If necessary, use a roller
stand (not included) with larger workpieces.
4.
Before trying new or complicated cutting techniques, study the procedure and
practice with scrap metal.
5.
6.
Plug the Power Cord (71) into the nearest 120 volt, grounded, electrical outlet.
Firmly grip the Handles (64, 65, 72) of the Saw with both hands. Depress the
Safety Lock Button (63), and squeeze the Trigger Switch (66) to turn on the Saw.
7.
8.
Allow the Saw Blade (10) to spin up to full speed before feeding the Saw Blade
into the workpiece.
Make straight cuts only. Do not attempt to twist the Saw to the right or left while
cutting. If this occurs, the Saw Blade (10) will “bind” in the workpiece causing
kickback, potential personal injury, and/or damage to the workpiece and Saw.
9.
Do not force the Saw to remove material faster than it was designed to cut.
Make sure to feed the Saw Blade (10) gradually into the workpiece.
10.
Turn off the Saw if the Saw Blade (10) is to be backed out of an uncompleted cut.
When turning off the Saw, allow the Saw Blade to fully stop on its own before
removing the Saw. Do not press against the Saw Blade to stop it.
11.
Once the cutting job is completed, turn off the Saw and wait until the Saw Blade
(10) has stopped rotating. Then, unplug the Power Cord (71) from its electrical
outlet.
SKU 94362
For technical questions, please call 1-800-444-3353.
Page 17
Download from Www.Somanuals.com. All Manuals Search And Download.
INSPECTION AND MAINTENANCE
1.
2.
WARNING! Always unplug the Saw from its electrical outlet before
performing any inspection, maintenance, or cleaning.
Before each use: Inspect the general condition of the Saw. Check for
misalignment or binding of moving parts, loose, cracked or broken parts,
damaged wiring, and any other condition that may affect its safe operation. If
abnormal noise or vibration occurs, have the problem corrected before further
use. Do not use damaged equipment.
3.
Daily: The Saw Blade (10) must be sharp and clean to perform properly.
Depending on materials cut and frequency of tool use, the Saw Blade may
become clogged with metal particles and dull. Dull Saw Blades rub the
workpiece rather than cut, which results in increased friction, higher
temperatures, and a burned workpiece. As often as possible, check the condition
of the Saw Blade and, if necessary, replace a worn Saw Blade with a new, 7-1/4”
diameter, metal cutting Saw Blade rated at 5,800 RPM or above.
(See “To Install A Saw Blade” section for further information.)
4.
DAILY: With a vacuum or compressed air, remove all metal debris from the
metal debris compartment of the Saw. To do so, lift up and open the Main Lock
Plate (59) to expose the metal debris compartment. Once cleaned, close and
lower the Main Lock Plate. Do not immerse the Saw in liquid. (See Figure J.)
MAIN LOCK PLATE (#59)
FIGURE J
5.
Periodically: The Saw features two Carbon Brushes (43) which, periodically,
should be examined for wear. The Carbon Brushes are located on each side of
the Motor Housing (41). To inspect or replace the Carbon Brushes, use a small
standard screwdriver to remove the Brush Covers (42). Then, carefully pull out
the Carbon Brushes. Examine the concave surface of the Carbon Brushes.
SKU 94362
For technical questions, please call 1-800-444-3353.
Page 18
Download from Www.Somanuals.com. All Manuals Search And Download.
If the Carbon Brushes appear to be in good condition, but only dirty, they can be
cleaned by rubbing with a pencil eraser. If there are large scratches on the
Carbon Brushes, replace both Carbon Brushes immediately with approved
replacement Carbon Brushes from Harbor Freight Tools. To reinstall the Carbon
Brushes, insert them into the two Brush Holders (44). Turn the Carbon Brushes
vertically so they will fit properly into the Brush Holders. Then, replace the Brush
Covers. (See Figure K.)
6.
Store the Saw in a clean, dry location.
MOTOR HOUSING
(#41)
BRUSH COVER (#42)
CARBON BRUSH (#43)
BRUSH HOLDER (#44)
FIGURE K
SKU 94362
For technical questions, please call 1-800-444-3353.
Page 19
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST
Part #
1
Description
Knob
Part # Description
28
Baffle
2
Plastic
29
Rip Guide Pin
Screw (M5)
Rubber Ring
Body
3
Screw (M5)
Transparent Panel
Cover
30
4
31
5
32*
33*
34*
35*
36*
37*
38*
39*
40*
41*
42
6
Screw
Screw (M5)
Bearing
7
Inner Cover
Bolt (M8)
Inner Flange
Saw Blade
Outer Flange
Blade Cover
Spring
8
Armature
Bearing
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
Ring Fender
Screw
Field
Bearing Sleeve
Motor Housing
Brush Cover
Brush
Plastic Washer
Screw (M5)
Bearing Retainer
Bearing
43
44
Brush Holder
Screw (M5)
Nut
Ring
45
Key
46
Arbor
47
Spring
Gear
48
Screw
Ring
49
Washer
Bearing
50
Lock Lever
Ring
Base
51
Spring
52
Depth Control Lever
Washer
Rivet
53
Screw
54
Screw (M8)
*NOTE: PARTS #32* THROUGH 41* MAY NOT BE ORDERED INDIVIDUALLY,
BUT MUST BE ORDERED AS A COMPLETE MOTOR ASSEMBLY (PART #76*).
SKU 94362
For technical questions, please call 1-800-444-3353.
Page 20
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST (CONTINUED)
Part #
55
Description
Outlet Box
Screw
Part # Description
66
67
68
69
70
71
72
73
74
Trigger Switch
56
Screw
57
Pin
Power Cord Clamp
Soft Grip
58
Screw
59
Main Lock Plate
Spring
Power Cord Guard
Power Cord
Side Handle
Rip Guide
60
61
Vice Lock Plate
Washer
62
63
Safety Lock Button
Handle (R)
Handle (L)
Blade Wrench
64
76* Motor Assembly
65
NOTE: Some parts are listed and shown for illustration purposes only, and are not available individually
as replacement parts.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY
DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR
DISTRIBUTOR MAKES ANY REPRESENTATION ORWARRANTY OF ANY KINDTOTHE BUYERTHAT HE
OR SHE IS QUALIFIEDTO MAKE ANY REPAIRSTOTHE PRODUCT, ORTHAT HE OR SHE IS QUALIFIED
TO REPLACE ANY PARTS OFTHE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR
EXPRESSLY STATESTHAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY
CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL
RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR
REPLACEMENT PARTSTHERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT
PARTSTHERETO.
SKU 94362
For technical questions, please call 1-800-444-3353.
Page 21
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY DIAGRAM
5
3
4
7
2
10
12
6
1
9
11
19
16 14
8
17
23
21
20
22
18
15
27
25
29
13
32*
42
30
33*
34*
39*
38*
37*
55
41*
26
31
43
44
40*
35*
36*
28
46
47
24
54
53
50
66
51
52
45
49
57
48
56
65
60
63
64
62
58
59
61
67
69
#72: SIDE HANDLE NOT SHOWN.
#73: RIP GUIDE NOT SHOWN.
#74:BLADEWRENCH NOT SHOWN.
68
71
70
*NOTE: PARTS #32* THROUGH 41* MAY NOT BE ORDERED INDIVIDUALLY,
BUT MUST BE ORDERED AS A COMPLETE MOTOR ASSEMBLY (PART #76*).
LIMITED 90 DAY WARRANTY
Harbor FreightTools Co. makes every effort to assure that its products meet high quality and durability standards,
and warrants to the original purchaser that this product is free from defects in materials and workmanship for
the period of ninety days from the date of purchase. This warranty does not apply to damage due directly or
indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, or to lack of
maintenance.We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent,
special or consequential damages arising from the use of our product. Some states do not allow the exclusion
or limitation of incidental or consequential damages, so the above limitation of exclusion may not apply to you.
THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with transportation charges
prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise. If our
inspection verifies the defect, we will either repair or replace the product at our election or we may elect to
refund the purchase price if we cannot readily and quickly provide you with a replacement. We will return
repaired products at our expense, but if we determine there is no defect, or that the defect resulted from
causes not within the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
3491 Mission Oaks Blvd.
•
PO Box 6009
•
Camarillo, CA 93011
•
(800) 444-3353
SKU 94362
For technical questions, please call 1-800-444-3353.
Page 22
Download from Www.Somanuals.com. All Manuals Search And Download.
|