3000 RATED WATTs/3500 MAX. WATTs
poRTAblE gEnERAToR
cERTifiED foR All sTATEs EXcEpT cAlifoRniA
Model 65414
sET up, opERATing, AnD sERvicing
insTRucTions
using an engine indoors cAn Kill You in
MinuTEs.
Engine exhaust contains carbon monoxide.
This is a poison you cannot see or smell.
nEvER use inside
a home or garage,
EvEn if doors and
windows are open.
only use ouTsiDE
and far away from
windows, doors, and
vents.
Read this material before using this product.
failure to do so can result in serious injury.
sAvE This MAnuAl.
©
®
Copyright 2009 by Harbor Freight Tools . All rights reserved. No portion of this manual or any artwork
contained herein may be reproduced in any shape or form without the express written consent of
Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein. Tools required for
assembly and service may not be included.
for technical questions or replacement parts, please call 1-800-444-3353.
Manual Revised 09j
Download from Www.Somanuals.com. All Manuals Search And Download.
cAuTion, used
with the safety
alert symbol, indicates a
hazardous situation which, if
not avoided, could result in
minor or moderate injury.
sAvE This MAnuAl
Keep this manual for the safety
warnings and precautions, assembly,
operating, inspection, maintenance and
cleaning procedures. Write the product’s
serial number in the back of the manual
near the assembly diagram (or month
and year of purchase if product has no
number). Keep this manual and the
receipt in a safe and dry place for future
reference.
noTicE is used to
address practices
not related to personal injury.
cAuTion, without
the safety alert
symbol, is used to address
practices not related to
personal injury.
iMpoRTAnT sAfETY
infoRMATion
in this manual, on the labeling,
and all other information
WARning! Read all instructions.
failure to follow all instructions
listed below may result in fire,
serious injury and/or DEATh.
The warnings and precautions
discussed in this manual cannot
cover all possible conditions and
situations that may occur. It must
be understood by the operator that
common sense and caution are
factors which cannot be built into
this product, but must be supplied
by the operator.
provided with this product:
This is the safety alert
symbol. it is used to alert
you to potential personal
injury hazards. obey all
safety messages that
follow this symbol to avoid
possible injury or death.
DAngER indicates
a hazardous
sAvE ThEsE insTRucTions
situation which, if not
avoided, will result in death or
serious injury.
sET up pREcAuTions
1. Gasoline fuel and fumes are
flammable, and potentially explosive.
Use proper fuel storage and handling
procedures. Do not store fuel or
other flammable materials nearby.
WARning
indicates a
hazardous situation which, if
not avoided, could result in
death or serious injury.
2. Have multiple ABC class fire
extinguishers nearby.
3. Operation of this equipment may
create sparks that can start fires
around dry vegetation.
SKU 65414
for technical questions, please call 1-800-444-3353.
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
2.
3.
Keep children away from the equipment,
especially while it is operating.
A spark arrestor may be required.
The operator should contact
local fire agencies for laws or
regulations relating to fire prevention
requirements.
Do not leave the equipment unattended
when it is running. Turn off the
equipment (and remove safety keys, if
available) before leaving the work area.
4. Set up and use only on a flat, level,
well-ventilated surface.
4.
5.
Wear ANSI-approved safety goggles and
hearing protection during use.
5. Wear ANSI-approved safety goggles,
heavy-duty work gloves, and dust
mask/respirator during set up and
use.
People with pacemakers should
consult their physician(s) before use.
Electromagnetic fields in close proximity
to a heart pacemaker could cause
pacemaker interference or pacemaker
failure. Caution is necessary when near
the engine’s magneto or recoil starter.
6. Use only oil and fuel recommended
in the “Specifications” section of this
manual.
6.
Use only accessories that are
recommended by Harbor Freight Tools
for your model. Accessories that may
be suitable for one piece of equipment
may become hazardous when used on
another piece of equipment.
opERATing pREcAuTions
1.
cARbon MonoXiDE
hAzARD
using an engine indoors
cAn Kill You in
MinuTEs.
7.
8.
Do not operate in explosive
atmospheres, such as in the presence
of flammable liquids, gases, or dust.
Gasoline-powered engines may ignite
the dust or fumes.
Engine exhaust contains carbon
monoxide. This is a poison you
cannot see or smell.
Stay alert, watch what you are doing
and use common sense when operating
this piece of equipment. Do not use
this piece of equipment while tired or
under the influence of drugs, alcohol or
medication.
NEVER use inside a home or garage,
EVEN IF doors and windows are
open.
9.
Do not overreach. Keep proper footing
and balance at all times. This enables
better control of the equipment in
unexpected situations.
10. Dress properly. Do not wear loose
clothing or jewelry. Keep hair, clothing
and gloves away from moving parts.
Loose clothes, jewelry or long hair can
be caught in moving parts.
Only use OUTSIDE and far away
from windows, doors, and vents.
Page 4
for technical questions, please call 1-800-444-3353.
SKU 65414
Download from Www.Somanuals.com. All Manuals Search And Download.
11. Parts, especially exhaust system
components, get very hot during use.
Stay clear of hot parts.
equipment and do not use the equipment
for a purpose for which it is not intended.
21. cAuTion: This generator is not
intended to power sensitive electronic
equipment* without the addition of an
appropriate line conditioner and surge
protector (both not included). Sensitive
electronic equipment should be operated
on approved inverter type generators or
pure sine wave generators.
12. Do not cover the engine or equipment
during operation.
13. Keep the equipment, engine, and
surrounding area clean at all times.
14. Use the equipment, accessories, etc., in
accordance with these instructions and
in the manner intended for the particular
type of equipment, taking into account
the working conditions and the work to
be performed. Use of the equipment for
operations different from those intended
could result in a hazardous situation.
If the plugged in product operates
abnormally or unusually slow,
immediately stop using the generator
as a power source. Always read and
adhere to the instruction manual of the
product to be powered, to make sure that
it can be safely and efficiently powered
by a portable generator.
15. Do not operate the equipment with
known leaks in the engine’s fuel system.
note: When using a generator to
provide home standby electricity, a
transfer switch (sold separately) is
needed to prevent back feeding power
into the utility line.
16. This product contains or, when used,
produces a chemical known to the State
of California to cause cancer and birth
defects or other reproductive harm.
(California Health & Safety Code §
25249.5, et seq.)
Connections for standby power to a
building electrical system must be made
by a qualified electrician. The connection
must isolate the generator power from
utility power, and must comply with all
applicable laws and electrical codes.
17. When spills of fuel or oil occur, they must
be cleaned up immediately. Dispose
of fluids and cleaning materials as per
any local, state, or federal codes and
regulations. Store oil rags in a bottom-
ventilated, covered, metal container.
WARning: Improper connections to
a building electrical system can allow
electrical current from the generator
to backfeed into the utility lines. Such
backfeed may electrocute utility company
workers or others who contact the
lines during a power outage, and the
generator may explode, burn, or cause
fires when utility power is restored.
Consult the utility company or a qualified
electrician.
18. Keep hands and feet away from moving
parts. Do not reach over or across
equipment while operating.
19. Before use, check for misalignment
or binding of moving parts, breakage
of parts, and any other condition that
may affect the equipment’s operation.
if damaged, have the equipment
serviced before using. Many accidents
are caused by poorly maintained
equipment.
*sensitive electronic equipment
includes, but is not limited to, audio/
video equipment, some television
sets, computers, and printers.
20. Use the correct equipment for the
application. Do not modify the
SKU 65414
for technical questions, please call 1-800-444-3353.
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Ac ApplicATions
3.
Do not alter or adjust any part of the
equipment or its engine that is sealed
by the manufacturer or distributor.
Only a qualified service technician
may adjust parts that may increase or
decrease governed engine speed.
1.
2.
Before connecting an appliance or
power cord to the generator: Make sure
that it is in good working order. Faulty
appliances or power cords can create a
potential for electrical shock.
4.
5.
Wear ANSI-approved safety goggles,
heavy-duty work gloves, and dust mask/
respirator during service.
If an appliance begins to operate
abnormally, becomes sluggish or
stops suddenly, turn it off immediately.
Disconnect the appliance, and determine
whether the problem is the appliance, or
if the rated load capacity of the generator
has been exceeded.
Maintain labels and nameplates on
the equipment. These carry important
information. If unreadable or missing,
contact Harbor Freight Tools for a
replacement.
3.
4.
Make sure that the electrical rating of
the tool or appliance does not exceed
that of the generator. Never exceed the
maximum power rating of the generator.
Power levels between rated and
maximum may be used for no more than
30 minutes.
6.
Have the equipment serviced by a
qualified repair person using only
identical replacement parts. This will
ensure that the safety of the equipment
is maintained. Do not attempt any
service or maintenance procedures
not explained in this manual or any
procedures that you are uncertain about
your ability to perform safely or correctly.
Substantial overloading will open the
circuit breaker. Exceeding the time limit
for maximum power operation or slightly
overloading the generator may not switch
the circuit breaker or circuit protector
OFF, but will shorten the service life of
the generator.
7.
8.
9.
Store equipment out of the reach of
children.
Follow scheduled engine and equipment
maintenance.
Refueling Precautions:
sERvicE pREcAuTions
a. Do not smoke, or allow sparks, flames,
or other sources of ignition around the
equipment, especially when refuelling.
1.
before service, maintenance, or
cleaning:
b. Do not refill the fuel tank while the
a. Turn the engine switch to its “off”
position.
engine is running or hot.
c. Do not fill fuel tank to the top. Leave
a little room for the fuel to expand as
needed.
b. Allow the engine to completely cool.
c. Then, remove the spark plug wire(s)
from the spark plug(s).
d. Refuel in a well-ventilated area only.
2.
Keep all safety guards in place and in
proper working order. Safety guards
include muffler, air cleaner, mechanical
guards, and heat shields, among other
guards.
sAvE ThEsE
insTRucTions.
Page 6
for technical questions, please call 1-800-444-3353.
SKU 65414
Download from Www.Somanuals.com. All Manuals Search And Download.
5. If you are using one extension cord
for more than one tool, add the
nameplate amperes and use the sum
to determine the required minimum
cord size.
Extension cords
1. Grounded tools require a three wire
extension cord. Double Insulated
tools can use either a two or three
wire extension cord.
(see Table A.)
2. As the distance from the supply
outlet increases, you must use a
heavier gauge extension cord. Using
extension cords with inadequately
sized wire causes a serious drop in
voltage, resulting in loss of power and
possible tool damage.
6. If you are using an extension cord
outdoors, make sure it is marked with
the suffix “W-A” (“W” in Canada) to
indicate it is acceptable for outdoor
use.
7. Make sure the extension cord is
properly wired and in good electrical
condition. Always replace a damaged
extension cord or have it repaired by
a qualified electrician before using it.
(see Table A.)
3. The smaller the gauge number of the
wire, the greater the capacity of the
cord. For example, a 14 gauge cord
can carry a higher current than a 16
gauge cord.
8. Protect the extension cords from
sharp objects, excessive heat, and
damp or wet areas.
(see Table A.)
4. When using more than one extension
cord to make up the total length,
make sure each cord contains at
least the minimum wire size required.
(see Table A.)
REcoMMEnDED MiniMuM WiRE gAugE foR EXTEnsion coRDs* (120/240 volT)
nAMEplATE
EXTEnsion coRD lEngTh
AMpEREs
(at full load)
25 feet
50 feet
75 feet
100 feet
150 feet
0 – 2.0
2.1 – 3.4
18
18
18
18
18
14
12
18
18
18
16
14
12
10
18
18
16
14
12
10
-
18
16
14
12
10
-
16
14
12
12
-
3.5 – 5.0
5.1 – 7.0
7.1 – 12.0
12.1 – 16.0
16.1 – 20.0
TAblE A
-
-
-
* Based on limiting the line voltage drop to five volts at 150% of the rated amperes.
SKU 65414
for technical questions, please call 1-800-444-3353.
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
functions
bAsic spEcificATions
This unit can power items such as the
following:
91+ octane premium
Type
unleaded gasoline
Fuel
Capacity 4 Gallons
iTEM
Running sTART-up
SAE 10W-30 above 32°F
Type
WATTs
1200
700
1050
1000
1650
1400
WATTs
2400
2200
2150
2100
3000
3100
SAE 5W-30 at 32°F or below
Belt Sander
Engine
Oil
Refrigerator/Freezer
1/2 HP Sump Pump
1/2 HP Well Pump
Miter Saw
1-1/2 HP Capacitor Start
& Run Motor
2/3 Quart; Low Oil Shutdown
Sensor
Capacity
Spark Plug Gap
0.030”
Run Time @ 50%
Load
9 Hours with full tank
6.5 HP Four-stroke Overhead
Valve Design
note: The above wattages are estimates.
Check nameplate wattages on all
Engine Type
Ignition
Recoil Start with Electronic
Ignition
loads before connecting to generator.
One 20A duplex NEMA
120V~receptacle
unpAcKing
One 25A NEMA 120V 3 prong
twist lock receptacle
Electrical Plugs
When unpacking, check to make sure
that the item is intact and undamaged. If
any parts are missing or broken, please
call Harbor Freight Tools at 1-800-444-
3353 as soon as possible.
One T-Type 12V outlet
note: Additional specifications found
in the TECHNICAL ENGINE
SPECIFICATIONS chart in this
manual.
The emission control system for
this Generator’s Engine is warranted for
standards set by the U.S. Environmental
Protection Agency. For warranty
information, refer to the last pages of this
manual.
At high altitudes, the engine’s
carburetor, governor (if so equipped), and
any other parts that control the fuel-air
ratio will need to be adjusted by a qualified
mechanic to allow efficient high-altitude
use and to prevent damage to the engine
and any other devices used with this
product.
REMOVE THESE BOLTS AND BRACKETS BEFORE USE!
There are two metal brackets that
secure the generator to the bottom of the
crate. These brackets hold the generator
in place during shipment to prevent
damage. They must be removed before
use. see the photo above.
Page 8
for technical questions, please call 1-800-444-3353.
SKU 65414
Download from Www.Somanuals.com. All Manuals Search And Download.
conTRols
Power Indicator Light
AC Circuit
Breaker Switch
Engine Power Switch
MAin bREAKER
120v Ac ouTlETs onlY
20A
REsET
120 V~ Duplex AC Reset
12 VDC Outlet
Ground Wire
Connection
Receptacle
Switch
120 V~
Twist Lock Receptacle
DC Circuit
Breaker Switch
Plug for up
to 15A
Plug for up
to 20A
120V Duplex
Receptacle
for 15A or 20A
plugs
note: Be sure to use the proper plug for the amps needed.
figure 1
SKU 65414
for technical questions, please call 1-800-444-3353.
Page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
low engine oil WILL permanently
damage the engine. check the oil
level with the engine stopped and
in a level position.
opERATing insTRucTions
Read the EnTiRE iMpoRTAnT
sAfETY infoRMATion
section at the beginning of this
manual including all text under
subheadings therein before set
up or use of this product.
1. Wipe dipstick exterior with a clean
cloth. Remove the dipstick and wipe
it off with a clean rag. Pour engine oil
into the oil fill hole until the level of oil
is even with the bottom edge of the
oil fill hole (if you cannot see the oil
through the oil fill hole, then the oil is
too low and more oil must be added).
To pREvEnT
sERious injuRY:
operate only with proper
spark arrestor installed.
operation of this equipment
may create sparks that can
start fires around dry
vegetation.
A spark arrestor may be
required.
The operator should contact
local fire agencies for laws or
regulations relating to fire
prevention requirements.
2. Reinsert the dipstick into the oil
filler neck, but do not screw in, then
remove it to check the oil level. The
oil level should reach the upper limit
(H) mark on the dipstick (bottom edge
of the oil fill hole).
3. If the oil level is not to the upper limit
mark (bottom edge of the oil fill hole),
add the appropriate type of oil until
the oil level reaches the upper limit
mark.
starting the Engine
This gEnERAToR hAs An AuTo-shuTDoWn
oil sEnsoR. if EnginE sTops oR Will
noT sTART, chEcK oil lEvEl.
inspect engine and equipment
looking for damaged, loose,
and missing parts before
set up and starting. if any
problems are found, do not use
equipment until fixed properly.
Before starting, first familiarize
yourself with proper shut down
and emergency shut down
procedures.
SAE 10W-30 above 32°F
Engine Oil
SAE 5W-30 at 32°F or below
checking and filling Engine oil
4. Replace the Oil Dipstick.
cAuTion! Your Warranty is VOID if the
engine’s crankcase is not properly
filled with oil before each use. Before
each use, check the oil level. Do not
run the engine with low or no engine
oil. Running the engine with no or
The Oil Sensor will automatically
shut down the engine before the oil
level falls below the safe/low limit.
To avoid nuisance tripping of the
Oil Sensor and damage to property,
check that the oil level is at the
Page 10
for technical questions, please call 1-800-444-3353.
SKU 65414
Download from Www.Somanuals.com. All Manuals Search And Download.
bottom edge of the oil fill hole before
each start-up.
b. fill the engine with the
proper amount and type of
fuel and oil.
cAuTion! Do noT run the engine with
low oil or no oil; the engine will be
permanently damaged.
c. Read the Equipment
operation section that
follows.
checking and filling fuel
1. Unplug loads from the Generator and
make sure the AC Circuit Breaker
Switch is in the OFF position before
starting to prevent permanent
generator damage.
1. Check the fuel level. If the fuel level
is more than 1” below the fill neck of
the fuel tank, add more fuel.
note: Do not overfill the fuel tank.
2. Turn the engine fuel valve to its ON
or OPEN position.
WARning! To pREvEnT
sERious injuRY fRoM
fiRE:
3. Turn the engine power switch to its
ON or RUN position.
Fill the fuel tank in a well-
ventilated area away from ignition
sources. Do not smoke.
4. Then, turn the engine choke lever to
its “CHOKE” position. Set the choke
lever in the “RUN” position when
starting a warm engine.
2. To fill the Fuel Tank, first wipe off the
Fuel Tank Cap and the surrounding
area.
5. Grasp the starter handle, and pull
slowly until resistance is felt. While
holding the handle, allow the starter
rope to rewind. Then, pull the starter
handle with a rapid, full arm stroke.
Once again while holding the handle,
allow the rope to rewind. Repeat as
necessary, until the engine starts.
3. Unscrew, and remove the Fuel Tank
Cap.
4. Mix fuel stabilizer (not included)
with 91 octane (or better) premium
unleaded gasoline according to fuel
stabilizer directions.
6. After the engine starts and warms
up, slowly move the choke lever to its
“RUN” position.
note: Use only premium octane unleaded
gasoline.
5. Fill the Fuel Tank to about 1 inch
under the fill neck of the gasoline
tank with the stabilized unleaded
gasoline mixture.
iMpoRTAnT: Allow the engine to run at
no load until warm (1-5 minutes) to
stabilize.
7. Move the AC Circuit Breaker Switch
to its ON or RUN position.
6. Then replace the Fuel Tank Cap.
start procedure
before starting the engine:
a. inspect the equipment and
engine.
SKU 65414
for technical questions, please call 1-800-444-3353.
Page 11
Download from Www.Somanuals.com. All Manuals Search And Download.
break-in period
1. Make sure your generator is properly
grounded to avoid electrical shocks.
Connect a 10 gauge or larger
1. Breaking-in the engine will help
to ensure proper equipment and
engine operation, and will extend
the engine’s lifespan. The warranty
is void if the engine is not broken
in properly. The first 20 hours of
operation is the break-in period.
insulated copper wire to the Ground
Connection on the Control Panel.
Connect this wire to a suitable
external ground, such as a metal
stake in the ground.
2. Don’t overload the generator. The
total wattage used by the appliances
should be less than the output rating
of the generator. If you put too many
appliances on the generator, it could
seriously damage the appliances
and electronics. Overloading the
generator could also cause fires in
the power cord. This generator is
rated at 3000 / 3500 Watts.
2. During the first 3 hours of use:
• Do not apply a heavy load to the
equipment.
3. After the first 20 hours of use:
• Change the engine oil.
Under normal operating conditions
subsequent maintenance follows
the schedule explained in the
MAINTENANCE AND SERVICING
section.
note: At start-up, appliances draw more
power in a surge than they do during
continuous operation. When figur-
ing total wattage of all appliances
connected to this generator, use the
higher start-up amperage rating of
each appliance.
Equipment operation
To pREvEnT
sERious injuRY
AnD DEATh:
Do noT connEcT
3. Do not exceed the current limit
gEnERAToR DiREcTlY To
housEholD WiRing.
A portable electric generator
that is connected to your
household wiring without a
proper cut off switch can
‘back feed’ into the power
lines connected to your home.
power created by your
generator can injure or even
kill a utility lineman making
outage repairs many miles
away.
specified for any one receptacle.
4. Move the AC Circuit Breaker switch
to the ON position.
5. Plug in your extension cord or
appliance.
6. Be sure that all appliances are in
good working order before connecting
them to the generator. If an appliance
begins to operate abnormally,
becomes sluggish, or stops suddenly,
turn off the AC Circuit Breaker and
the generator Engine Power Switch
immediately. Then disconnect the
appliance and examine it for signs of
malfunction.
Only a certified electrician can
safely connect the generator
to your home’s wiring.
Page 12
for technical questions, please call 1-800-444-3353.
SKU 65414
Download from Www.Somanuals.com. All Manuals Search And Download.
note: If an overloaded circuit causes the
AC Circuit Breaker to switch off,
reduce the electrical load on the
circuit and wait a few minutes before
resetting the circuit breaker.
3. AC Circuit Breaker Switch protects
circuits when using AC power.
4. 120 V~ duplex outlet provides two
grounded outlets for standard 110-
120 V~ household appliances.
The outlets are configured for both
standard 15A plugs or 20A plugs -
See Figure 1 “Controls”.
7. The DC terminal may be used
to operate 12 Volt DC portable
appliances only.
cAuTion! Do not use this
generator to charge 12vDc
batteries. Directly charging a 12
volt battery may cause the battery
to overheat and possibly explode.
cAuTion: Do not attempt to start
an automobile engine with this
generator. voltage back feed from
the alternator may damage the
generator.
5. 120 V~ twist lock receptacle provides
a grounded outlet for one 120 Volt
appliance, such as a water heater.
6. 12 VDC outlet provides a power
source for 12 volt DC items, such
as automotive accessories. 12 VDC
Circuit Breaker Switch provides circuit
protection for 12 VDC accessories.
note: The DC terminal may be used
while the AC power is in use. An
overloaded DC circuit will trip the DC
circuit protector (push button comes
out). If this happens, wait a few
minutes before pushing in the circuit
protector to resume operation.
8. Disconnect all loads from the
generator before shutting off. To
prevent accidents, turn off the engine
and disconnect its spark plug wire
after use. Wait for the engine to
cool, clean external parts with clean
cloth, then store the equipment out
of children’s reach according to the
Storage instructions in this manual.
control panel features
1. Engine Power Switch must be in ON
position for engine to start and run.
Move to OFF position to stop engine.
2. Power Indicator Light, when lit,
shows that the generator is producing
electrical energy.
SKU 65414
for technical questions, please call 1-800-444-3353.
Page 13
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance procedures
TEchnicAl
spEcificATions
Many maintenance procedures,
including those not detailed
in this manual, will need to
be performed by a qualified
technician for safety. if you
have any doubts about your
ability to safely service the
equipment or engine, have a
qualified technician service the
equipment instead.
Engine Type
4 Stroke, OHV
68 x 54mm
8.5:1
Bore x Stroke
Compression Ratio
Displacement
196cc
91+ octane premium
unleaded gasoline
Type
Fuel
Capacity
4 Gallons
SAE10W-30 above 32° F
SAE 5W-30 at 32° F or
below
Type
Engine Oil
note: Warranty is void if proper
maintenance and servicing
procedures are not followed.
Capacity
2/3 Quarts
NGK BP61S
Bosch W6DC
Champion N11YC
Compatible
Spark
Types
Plug
Gap
Engine oil change
0.030”
Intake
0.1mm
Valve
Clearance
cAuTion! Oil is very hot during
operation and can cause burns. Wait
for engine to cool before changing oil.
Exhaust
0.15mm
3600 RPM
Speed
1. Place a drain pan (not included)
underneath the crankcase’s drain
plug.
sERvicing
To pREvEnT
sERious injuRY
fRoM AcciDEnTAl
sTARTing:
2. Remove the Drain Plug (1a) and, if
possible, tilt the crankcase slightly to
help drain the oil out. Recycle used
oil.
Turn the power switch of the
equipment to its “off”
position, wait for the engine to
cool, and disconnect the
spark plug wire(s) before
performing any inspection,
maintenance, or cleaning
procedures.
3. If the Drain Plug Washer (2a) is
damaged, replace with a new
Washer.
4. Re-install the Drain Plug and tighten
it in place.
5. Refill the oil to the proper level
following the instructions under the
Starting the Engine section.
To pREvEnT
sERious injuRY
fRoM EquipMEnT fAiluRE:
Do not use damaged
equipment. if abnormal noise,
vibration, or excess smoking
occurs, have the problem
corrected before further use.
Air filter Element Maintenance
1. Wipe off the air cleaner cover.
Page 14
for technical questions, please call 1-800-444-3353.
SKU 65414
Download from Www.Somanuals.com. All Manuals Search And Download.
2. The air cleaner cover is held in place
by clamps. Remove the clamps and
the cover.
Gasket-style: Finger-tighten until the
gasket contacts the cylinder head,
then about 1/2-2/3 turn more.
Non-gasket-style: Finger-tighten until
the plug contacts the head, then
about 1/16 turn more.
3. Remove the air filter element.
4. cleaning:
a. There are two foam filter elements.
Wash them in warm water and mild
liquid soap several times. Rinse.
Squeeze out excess water and allow
it to dry completely.
6. Apply dielectric spark plug boot
protector (not included) to the end of
the spark plug and reattach the wire
securely.
b. Soak the filter in lightweight oil
briefly, then squeeze out the excess
oil.
5. Install the new filter or the cleaned
filter. Secure the Air Cleaner Cover
before use.
spark plug Maintenance
1. Disconnect spark plug wire from
end of plug. Clean out debris from
around spark plug.
2. Using a spark plug wrench, remove
the spark plug.
3. Inspect the spark plug:
If the electrode is oily, clean it using a
clean, dry rag.
If the electrode has deposits on it,
polish it using emery paper.
If the white insulator is cracked or
chipped, the spark plug needs to be
replaced.
4. When installing a new spark
plug, adjust the plug’s gap to the
specification on the Technical
specification chart. Do not pry
against the electrode or the insulator,
the spark plug can be damaged.
5. Install the new spark plug or the
cleaned spark plug into the engine.
SKU 65414
for technical questions, please call 1-800-444-3353.
Page 15
Download from Www.Somanuals.com. All Manuals Search And Download.
Every 300 operation hours:
cleaning, Maintenance, and
lubrication schedule
a. Clean fuel tank and carburetor.
b. Clean carbon build-up from
combustion chamber.
note: This maintenance schedule
is intended solely as a general
guide. If performance decreases
or if equipment operates unusually,
check systems immediately. The
maintenance needs of each piece
of equipment will differ depending
on factors such as duty cycle,
temperature, air quality, fuel quality,
and other factors.
c. Check oil tube condition and replace
as needed.
storage
1. Wait for engine to cool, then clean
engine with clean cloth.
2. When the equipment is to remain idle
for longer than 20 days, prepare the
engine for storage as follows:
note: These procedures are in addition to
the regular checks and maintenance
explained as part of the regular
operation of the engine and
equipment.
a. Change engine oil and empty fuel
tank.
b. Either leave fuel tank empty or
refill fuel tank with fresh unleaded
gasoline mixed with a fuel stabilizer
intended for long term engine
After initial 20 operation hour period:
a. Change engine oil.
storage (not included). After filling,
run engine for about 5-10 minutes
to circulate the treated gasoline
through the carburetor. Wait for
engine to cool before proceeding.
Every 25 operation hours Thereafter:
a. Clean/replace air filter element.
b. Inspect/clean spark plug.
c. Clean out area around spark plug.
Remove spark plug and pour one
tablespoon of engine oil into cylinder
through spark plug hole.
Every 50 operation hours:
a. Change engine oil.
b. Replace fuel filter (if equipped).
c. Check spark plug. Clean and re-gap
as needed.
d. Reinstall spark plug, but leave spark
plug wire disconnected.
e. Pull recoil starter to distribute oil
in cylinder. Stop after one or two
revolutions when you feel the piston
start the compression stroke (when
you start to feel resistance).
Every 100 operation hours:
a. Replace spark plug.
b. Replace air filter element.
c. Clean fuel tank and fuel strainer.
f. Disconnect battery cables (if
equipped).
note: All maintenance procedures
scheduled for 25, 50, and 100
operation hours should be performed
at least yearly.
3. Apply a thin coat of rust preventive oil
to all uncoated metal parts.
Page 16
for technical questions, please call 1-800-444-3353.
SKU 65414
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Cover and store in a dry, well-
ventilated area out of reach of
children.
5. Before starting the engine after
storage, keep in mind that untreated
gasoline will deteriorate quickly.
a. Place a container below the carbure-
tor bowl and drain the fuel from the
fuel tank and carburetor bowl.
b. Discard the drained fuel properly as
per local ordinance.
c. Change to fresh fuel if untreated
gasoline has been sitting for a
month, if treated gasoline has been
sitting beyond the fuel stabilizer’s
recommended time period, or if the
engine does not start properly.
SKU 65414
for technical questions, please call 1-800-444-3353.
Page 17
Download from Www.Somanuals.com. All Manuals Search And Download.
Engine Troubleshooting
Problem: Low power output. Engine bogs down or stops under load. Excess exhaust or
unburned fuel in exhaust. See chart below:
Engine system
possible cause
possible solution
Incorrect Ignition Timing.
Adjust Engine Advance Angle.
Ignition System
1. Air in fuel line or fuel line clogged. 1. Purge air or clear obstruction.
2. Main Jet not adjusted properly. 2. Readjust Main Jet.
3. Metering Jet or Main Jet clogged. 3. Clean and Readjust.
Fuel Supply System
4. Fuel Cock clogged.
4. Clean as needed.
5. Carbon Fouling in Combustion
Chamber.
5. Clean out Combustion Chamber.
6. Clogged Air Filter.
6. Clean or replace Air Filter.
7. Intake Manifold leaking.
7. Repair or replace as needed.
1. Worn Piston, Piston Ring or
Cylinder Wall.
1. Check compression and wear
tolerances, repair or replace as
needed.
Poor Compression
2. Leaking Cylinder Head Gasket.
2. Check compression, replace as
needed.
3. Worn Valves, Valve Seats, Stems 3. Check wear tolerances, repair or
or Valve Guides. replace as needed.
Problem: Engine does not start or does not run smoothly. See chart below:
Symptom
Possible Cause
Possible Solution
Excess wear of:
Check wear, replace as needed.
Engine is Pinging
•
•
•
•
Piston, Cylinder Wall or Rings.
Piston Pin or Piston Pin Hole.
Connecting Rod Wrist Pin.
Crankshaft Roller Bearing.
1. Combustion chamber carbon
fouling.
1. Clean out Combustion chamber and
spark plug.
Abnormal Com-
bustion or engine
running hot or
2. Dirty or old gasoline or oil in gas. 2. Drain gas, clean out fuel filter and
replace with fresh gas, minimum 91
excess smoking.
octane premium unleaded gasoline.
1. Engine Switch in OFF position.
2. Water in Carburetor Bowl.
1. Move Switch to ON position.
Engine does not
start.
2. Drain carburetor Bowl, clean Fuel
Filter.
3. Spark Plug gap not correct.
3. Clean and re-gap plug at 0.030”.
Replace plug if needed.
4. Incorrect Ignition Timing.
5. Damaged coil or ignition wires.
6. Low Oil level.
4. Check timing and adjust.
5. Check for damaged wires, test output.
6. Check oil level, top off as needed.
Page 18
for technical questions, please call 1-800-444-3353.
SKU 65414
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Poor Fuel quality.
1. Replace fuel with 91+ octane premium
unleaded gasoline.
Engine not run-
ning Smoothly
2. Incorrect choke setting.
3. Incorrect Timing.
2. Adjust the choke.
3. Have the timing checked by a qualified
technician.
Problem: Engine stops suddenly while running. See chart below:
Engine system possible cause
possible solution
1. Fuel is used up.
1. Check fuel level and refill as needed.
Fuel Supply
2. Fuel Filter is clogged.
3. Carburetor Float is leaking.
4. Needle Valve sticks.
2. Clean Fuel Filter.
System
3. Replace if needed.
4. Clean and readjust.
1. Engine Switch is in OFF position. 1. Move Switch to ON position.
Ignition System
2. Spark Plug tip is burned through
or carbon fouled.
2. Clean or replace spark plug. Reset
gap to 0.030”.
3. Spark Plug Wire is disconnected. 3. Check connections at both ends.
4. Spark Plug wire is shorting against 4. Check condition of spark plug wire,
engine body or frame.
replace as needed.
5. Ignition Coil is shorted or
damaged.
5. Check coil continuity and output.
1. Engine Piston, Piston Rod, Valve
or Crankshaft may be damaged.
1. Have serviced by a qualified
Mechanical
problem
technician.
2. Generator Shaft may be seized.
2. Disconnect engine and attempt to
rotate generator shaft by hand. Repair
or replace as needed.
Problem: Engine runs excessively hot. See chart below:
Problem
Possible Cause
Possible Solution
1. Improper Ignition Timing.
1. Check and reset Ignition Timing.
Engine runs
excessively
hot
2. Exhaust manifold, muffler or exhaust
2. Check condition of exhaust system,
repair as needed.
pipe damaged or clogged.
3. Intake Manifold leaking.
3. Check condition of intake manifold
and gasket. Repair as needed.
4. Dirty or clogged Cylinder Cooling Fins. 4. Clean Cylinder Wall Cooling Fins.
5. Cooling Fan loose or damaged.
5. Check condition of cooling fan.
Repair or replace as needed.
6. Bent Piston Rod
6. Replace Piston Rod.
7. Worn Piston, Piston Ring or Cylinder
Wall.
7. Check clearances, replace as
needed.
8. Improper engine speed.
8. Engine speed is self-regulating. Be
sure choke if fully open. Reduce
electrical load on generator.
9. Worn Crankshaft Main Bearing.
9. Check for wear. Replace as needed.
SKU 65414
for technical questions, please call 1-800-444-3353.
Page 19
Download from Www.Somanuals.com. All Manuals Search And Download.
Equipment Troubleshooting
problem
possible causes
probable solutions
1. No fuel in tank.
1. Refill the fuel tank.
Engine Will Not
Start
2. Engine Switch in OFF position.
2. Move the Switch to the ON
position.
3. Fuel Valve turned OFF.
4. Engine Oil level low.
5. No spark at spark plug.
3. Turn the fuel valve ON.
4. Top off oil level.
5. Check that the spark plug wire is
not loose or disconnected. Clean
and re-gap spark plug. Replace if
necessary.
6. No fuel reaching carburetor.
6. Clean fuel filter cup. Check fuel line
for leaks or obstructions.
1. Fuel filter dirty.
1. Check and clean the fuel filter.
2. Check and clean the air filter.
Engine misses,
is hard to start or
runs poorly
2. Air cleaner dirty.
3. Spark plug dirty or wrong gap.
3. Check, clean and re-gap spark
plug.
1. Engine is running poorly.
1. Improve engine performance.
2. Connect ground wire.
Power Light does
not come on
2. Ground wire is not connected.
3. Generator is not functioning.
3. Take generator to qualified service
technician.
1. AC Breaker switch in the OFF
position.
1. Reset the Breaker Switch to the ON
position.
No or not enough
power at the AC
outlets
2. AC circuits overloaded.
2. Disconnect some appliances to
reduce the load.
DC Breaker Switch open.
Disconnect the 12 Volt appliance, then
press the 12 VDC breaker switch IN.
Reconnect the 12 V accessory.
No power at the
12 VDC outlet
follow all safety precautions whenever diagnosing or servicing the
equipment or engine. Consult a qualified service technician for any
repairs beyond your training or ability.
plEAsE READ ThE folloWing cAREfullY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY
DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR
DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT
HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS
QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR
DISTRIBUTOR ExPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE
UNDERTAKEN BY CERTIFIEDAND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER
ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL
PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION
OF REPLACEMENT PARTS THERETO.
Page 20
for technical questions, please call 1-800-444-3353.
SKU 65414
Download from Www.Somanuals.com. All Manuals Search And Download.
MAin pARTs lisT
part
1
Description
Gasoline Engine
qty
1
part
24
Description
Exhaust Gasket
qty
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
Front Cover
1
16
7
6
1
1
5
1
1
1
1
1
7
1
8
5
8
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
Muffler
Flange Screw M8
Frame
1
18
1
4
4
10
4
10
1
1
1
1
1
4
1
1
1
1
1
Flange Screw M8x25
Spring Washer 8
Washer 8
Rotor Assembly
Stator Assembly
Plain washer 8
Screw 7/16(24UNC)-210
Protection board
Rear cover
Shock Absorber
Shock Absorber
Flange Screw M6x12
Plain washer 6
Flange Screw M6
Grounding Wire (10cm) φ6+φ6
Toothed Washer 6
Muffler Hood (YAMA)
Muffler Hood (YAMA)
Control Panel Assembly
Flange Bolt M6x16
Fuel Tank
Fuel Marker
Fuel Tank Cap Assembly
Strainer
Fuel Tank Cock Assembly
Fuel Pipe
Hoop
Carbon brush
5 KW Automatic Voltage Regulator
Flange Screw M5x16
Connection pole
Screw M5
Spring Washer 5
Washer 5
Spring Washer 6
Toothed Washer 5
Flange Screw M6x130
Rear cover
5
2
4
1
1
1
2
Flange Screw M5x12
2
Flange Screw M6x45
SKU 65414
for technical questions, please call 1-800-444-3353.
Page 21
Download from Www.Somanuals.com. All Manuals Search And Download.
DiAgRAM
Page 22
for technical questions, please call 1-800-444-3353.
SKU 65414
Download from Www.Somanuals.com. All Manuals Search And Download.
parts list and Diagram A -
crankcase Assembly
noTE: All part numbers listed on the following pages have a letter suffix. For example,
the Crankcase Cover shown in the above diagram is part # 12a. Whenever refer-
ring to engine sub-assembly parts, be sure to include the complete part number
including the letter suffix.
part #
1a
Description
Drain Plug
qty
2
part #
Description
Snap Ring
qty
1
9a
2a
3a
4a
5a
Drain Plug Washer
Crankshaft Oil Seal
Crankcase
Regulating Sway Bar
Washer
2
2
1
1
10a Driven Gear Assembly
11a Dipstick with Seal
12a Crankcase Cover
13a Crankcase Gasket
14a Bearing 6205
1
2
1
1
6a
1
2
7a
8a
Split Pin
Regulating Shaft
1
1
15a Set Pin m 8 x 14
16a Bolt m8 x 33.5
2
6
noTE: Not all engine sub-assembly components shown on the following pages are
available as separate replacement parts. They may be shown for informational
purposes only.
SKU 65414
for technical questions, please call 1-800-444-3353.
Page 23
Download from Www.Somanuals.com. All Manuals Search And Download.
parts list and Diagram b -
cylinder head Assembly
part #
1b
Description
qty
6
1
1
1
part #
13b
Description
Cylinder Head Gasket
Set Pin
Exhaust Valve
Intake Valve
Tappet
qty
1
2
1
1
Bolt m 6 x 12
14b
15b
16b
17b
2b
3b
4b
5b
Cylinder Head Cover
Cylinder Head Cover Gasket
Valve Rocker Assembly
Push Guide
1
2
18b
6b
Cap
1
Pusher
2
19b
20b
21b
22b
7b
8b
9b
10b
11b
12b
Exhaust Spring Seat
Intake Spring Seat
Valve Spring
Bolt m 8 x 60
Stud AM 8 x 34
1
1
2
4
2
1
Stud AM 6 x 112
Lead Wind Cover
Oil Pipe Seal
Clip
2
1
1
2
Cylinder Head Assembly
Page 24
for technical questions, please call 1-800-444-3353.
SKU 65414
Download from Www.Somanuals.com. All Manuals Search And Download.
parts list and Diagram c -
crankshaft, piston, connecting Rod, camshaft and flywheel
Assemblies
part #
1c
Description
qty
part #
7c
Description
qty
Piston Ring Set
1
2
1
1
1
1
Camshaft Assembly
Flywheel
1
1
1
1
1
2c
3c
4c
5c
Piston Ring Circlip
Piston
Piston Pin
Connecting Rod Assembly
Crankshaft Assembly
8c
9c
Flywheel Fan
10c Starting Flange
11c Nut m 14 x 1.5
6c
SKU 65414
for technical questions, please call 1-800-444-3353.
Page 25
Download from Www.Somanuals.com. All Manuals Search And Download.
parts list and Diagram D -
Recoil starter and ignition coil Assembly
part #
1d
Description
qty
part #
7d
Description
qty
Engine Switch
1
2
5
4
1
1
Diode
1
1
2
2
1
1
2d
3d
4d
5d
Fan Hood
Bolt m 6 x 12
Bolt m 6 x 8
Recoil Starter Assembly
Complete Shroud
8d
9d
Oil Sensor
Bolt m 6 x 14
10d Bolt m 6 x 22
11d Ignition Coil Assembly
12d Spark Plug F6TC
6d
Page 26
for technical questions, please call 1-800-444-3353.
SKU 65414
Download from Www.Somanuals.com. All Manuals Search And Download.
parts list and Diagram E -
Air Cleaner and Muffler Assembly
part #
1e
Description
qty
Air Cleaner Assembly
Nut m6
Air Duct
1
2
1
2e
3e
parts list and Diagram f -
fuel supply system
part
Description
qty
2
part
Description
qty
1
1f Pipe Clamp
8f Regulator Assembly
2f Fuel Pipe m 4.5 x 170
3f Intake Gasket
4f Connecting Block
5f Carburetor Gasket
6f Carburetor Assembly
7f Air Cleaner Gasket
1
1
1
1
1
1
9f Back Spring
10f Regulating Spring
11f Pulling Rod
12f Lock Bolt
13f Regulating Spring
14f Nut M6
1
1
1
1
1
1
SKU 65414
for technical questions, please call 1-800-444-3353.
Page 27
Download from Www.Somanuals.com. All Manuals Search And Download.
parts list and Diagram g -
starter and generator Assembly
part #
1g
Description
Starting Motor Assembly
Bolt m6 x 28
Bolt m6 x 32
Crankcase
qty
part #
6g
Description
qty
1
1
1
1
1
Bolt m6 x 35
2
1
2
1
2g
3g
4g
5g
7g
8g
9g
Clamp Cord
Bolt m6 x 12
Flywheel
Charge Coil
Record product’s serial number here:
note: If product has no serial number, record month and year of purchase instead.
note: Some parts are listed and shown for illustration purposes only, and are not avail-
able individually as replacement parts.
Page 28
for technical questions, please call 1-800-444-3353.
SKU 65414
Download from Www.Somanuals.com. All Manuals Search And Download.
Wiring Diagram
SKU 65414
for technical questions, please call 1-800-444-3353.
Page 29
Download from Www.Somanuals.com. All Manuals Search And Download.
quickly provide you with a replacement. We
will return repaired products at our expense,
but if we determine there is no defect, or that
the defect resulted from causes not within
the scope of our warranty, then you must
bear the cost of returning the product.
liMiTED 1 YEAR / 90 DAY
WARRAnTY
Harbor Freight Tools Co. makes every
effort to assure that its products meet high
qualityanddurabilitystandards, andwarrants
to the original purchaser that for a period of
ninety days from date of purchase that the
engine/motor, the belts (if so equipped),
and the blades (if so equipped) are free
of defects in materials and workmanship.
Harbor Freight Tools also warrants to the
original purchaser, for a period of one year
from date of purchase, that all other parts
and components of the product are free from
defects in materials and workmanship (90
days if used by a professional contractor or
if used as rental equipment). This warranty
does not apply to damage due directly or
indirectly, to misuse, abuse, negligence
or accidents, repairs or alterations outside
our facilities, normal wear and tear, or to
lack of maintenance. We shall in no event
be liable for death, injuries to persons
or property, or for incidental, contingent,
special or consequential damages arising
from the use of our product. Some states
do not allow the exclusion or limitation of
incidental or consequential damages, so the
above limitation of exclusion may not apply
to you. THIS WARRANTY IS ExPRESSLY
IN LIEU OF ALL OTHER WARRANTIES,
ExPRESS OR IMPLIED, INCLUDING THE
WARRANTIES OF MERCHANTABILITY
AND FITNESS.
This warranty gives you specific legal
rights and you may also have other rights
which vary from state to state.
3491 Mission Oaks Blvd. • PO Box
6009 • Camarillo, CA 93011 • (800)
444-3353
EMission conTRol
sYsTEM WARRAnTY
united states Emission control Defects
Warranty statement
The United States Environmental Protection Agency (herein
EPA) and Harbor Freight Tools (herein HFT) are pleased to explain
the emission control system warranty on your 1997 and later Small
Off-Road Engine (herein engine). Within the United States, new
off-road, spark-ignition engines certified for model year 1997 and
later, must be designed, built and equipped to meet the stringent
anti-smog standards set forth by the EPA. HFT must warrant the
emission control system on your engine for the periods of time
described below, provided there has been no abuse, neglect or
improper maintenance of your engine.
Your emission control system may include parts such as the
carburetor or fuel-injection system, and the ignition system. Also
included may be hoses, belts, connectors and other emission-
related assemblies.
Where a warrantable condition exists, HFT will repair your
engine at no cost to you including diagnosis, parts and labor.
Manufacturer’s Warranty coverage
The 1997 and later engines are warranted for two (2) years.
If any emission-related part on your engine is defective, the part
will be repaired or replaced by HFT.
harbor freight Tools Emission control Defects
Warranty coverage
To take advantage of this warranty,
the product or part must be returned to us
with transportation charges prepaid. Proof
of purchase date and an explanation of the
complaintmustaccompanythemerchandise.
If our inspection verifies the defect, we will
either repair or replace the product at our
election or we may elect to refund the
purchase price if we cannot readily and
Engines are warranted for a period of two (2) years relative to
emission control parts defects, subject to the provisions set forth
below. If any emission related part on your engine is defective,
the part will be repaired or replaced by HFT.
owner’s Warranty Responsibilities
• As the engine owner, you are responsible for the performance
of the required maintenance listed in your Owner’s Manual.
HFT recommends that you retain all receipts covering
maintenance on your engine, but HFT cannot deny warranty
solely for the lack of receipts or for your failure to ensure the
performance of all scheduled maintenance.
Page 30
for technical questions, please call 1-800-444-3353.
SKU 65414
Download from Www.Somanuals.com. All Manuals Search And Download.
• As the engine owner, you should, however, be aware that
HFT may deny you warranty coverage if your engine or a part
has failed due to abuse, neglect, improper maintenance, or
unapproved modifications.
replacement point for that part. Any replacement part,
provided it is equivalent in durability and performance, may
be used in performance of maintenance or repairs. The
owner is responsible for commissioning a qualified technician/
mechanic to perform all required maintenance, as outlined
in the Inspection, Cleaning, and Maintenance section in this
manual.
• You are responsible for shipping your engine to a HFT
warranty station as soon as a problem exists. Contact the
HFT Customer Service department at the number below to
make shipping arrangements. The warranty repairs should
be completed in a reasonable amount of time, not to exceed
30 days.
6. Warranted parts
1) fuel Metering system
i)
Carburetor and its internal parts.
If you have any questions regarding your warranty rights
and responsibilities, you should contact the Harbor Freight Tools
Customer Service Department at 1-800-444-3353.
ii) Fuel pump (if so equipped).
iii) Cold start enrichment system.
2) Air induction system
harbor freight Tools Emission control Defects
Warranty provisions
i)
Intake pipe/manifold.
ii) Air cleaner.
3) ignition system
1. length of coverage
i)
Spark plug.
HFT warrants to a first retail purchaser and each subsequent
purchaser that the engine is free from defects in materials
and workmanship that cause the failure of warranted parts
for a period of two (2) years after the date of delivery to the
first retail purchaser.
ii) Magneto ignition system.
4) catalyst system (if so equipped)
i)
Exhaust pipe stud.
ii) Muffler.
2. no charge Repair or Replacement
iii) Catalytic converter (if so equipped).
5) Miscellaneous items used in Above systems
Repair or replacement of any warranted part will be performed
at no charge to the owner if the work is performed through a
warranty station authorized by HFT. For emissions warranty
service, contact the HFT Customer Service Department at
1-800-444-3353.
i)
Vacuum, temperature and time sensitive valves
and switches.
ii) Hoses, belts, connectors, and assemblies.
3. consequential Damages coverage
Coverage under this warranty shall also extend to the failure
of any engine components caused by the failure of any
warranted part while it is still covered under this warranty.
4. coverage Exclusions
Warranty claims shall be filed in accordance with the
provisions of the HFT warranty policy explained in the box
at the top of the previous page. HFT shall not be liable for
any loss of use of the engine, for any alternative usage,
for any damage to goods, loss of time, or inconvenience.
Warranty coverage shall also be excluded for any part which
fails, malfunctions, or is damaged due to failure to follow
the maintenance and operating instructions set forth in the
Owner’s Manual including, but not limited to:
a) Use of parts which are not authorized by HFT
b) Improper installation, adjustment or repair of the engine
or of any warranted part unless performed by an
authorized warranty center
c) Failure to follow recommendations on fuel use contained
in the Owner’s Manual
d) Improper or inadequate maintenance of any warranted
parts
e) Repairs performed outside of the authorized warranty
service dealers
f)
Alterations by changing, adding to or removing parts
from the engine.
5. service and Maintenance
Component parts which are not scheduled for replacement
as required maintenance or are scheduled only for regular
inspection to the effect of “repair or replace as necessary”
are warranted for the warranty period. Any warranted part
which is scheduled for replacement as required maintenance
is warranted for the period of time up to the first scheduled
SKU 65414
for technical questions, please call 1-800-444-3353.
Page 31
Download from Www.Somanuals.com. All Manuals Search And Download.
|