OUTDOOR
MODEL
04201101
STOVE TOP
05101194
To installer or assembler:
Leave this manual with consumer
for future reference.
To consumer:
Keep this manual for future reference.
FOR OUTDOOR USE ONLY.
DANGER
WARNING
California Proposition 65
If you smell gas:
1. Shut off gas to the appliance.
2. Extinguish any open flame.
Combustion by-products produced when
using this product contain chemicals
known to the State of California to cause
cancer, birth defects, or other
3. Open lid.
4. If odor continues, keep away from the appliance and
immediately call your gas supplier or your fire department.
reproductive harm.
WARNING
WARNING
Improper installation, adjustment,
alteration, service or maintenance can
cause injury or property damage. Read the
installation, operating and maintenance
instructions thoroughly before installing
or servicing this equipment.
1. Do not store or use gasoline or other flammable liquids or
vapors in the vicinity of this or any other appliance.
2. An LP cylinder not connected for use shall not be stored in
the vicinity of this or any other appliance.
If you have any questions or need assistance during assembly, please call 1-800-232-3398.
To insure your satisfaction and for follow-up service, register your product online at www.grillregistration.com
05101194 • 42804116 • 07-14-05
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Use and Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10
Safety Symbols. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Installation Safety Precautions. . . . . . . . . . . . . . . . . . . 2
Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
LP Cylinder Removal, Transport, and Storage. . . . . . . 4
LP Cylinder. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
LP (Liquefied Petroleum Gas) . . . . . . . . . . . . . . . . . . . 4
LP Cylinder Filling. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
LP Cylinder Exchange . . . . . . . . . . . . . . . . . . . . . . . . . 5
LP Cylinder Leak Test. . . . . . . . . . . . . . . . . . . . . . . . . . 5
Connecting Regulator to the LP Cylinder . . . . . . . . . 5-6
Leak Testing Valve, Hose, and Regulator. . . . . . . . . . . 6
Safety Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Ignitor Lighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Match Lighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Burner Flame Check. . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Burner Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Turning Appliance Off. . . . . . . . . . . . . . . . . . . . . . . . . . 7
Ignitor Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Valve Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Hose Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Natural Hazard • Spiders . . . . . . . . . . . . . . . . . . . . . . . 8
Care and Cleaning of Stainless Steel. . . . . . . . . . . . . . 9
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Parts List. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Parts Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-17
Registration Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
To insure your satisfaction and for follow-up service,
register your product online at:
3
Download from Www.Somanuals.com. All Manuals Search And Download.
LP Cylinder
•
The LP cylinder used with your Outdoor Stove Top
must meet the following requirements:
DANGER
• NEVER store a spare LP cylinder under or near
the appliance or in an enclosed area.
•
Purchase LP cylinders only with these required
measurements: 12” (30.5cm) (diameter) x 18” (45.7
cm) (tall) with 20 lb. (9 kg.) Capacity maximum.
• Never fill a cylinder beyond 80% full.
• An over filled or improperly stored cylinder is a
hazard due to possible gas release from the
safety relief valve. This could cause an intense
fire with risk of property damage, serious injury
or death.
•
•
Be constructed and marked in accordance with
specifications for LP cylinder of the U.S. Department of
Transportation (DOT). See LP cylinder collar for
marking.
• If you see, smell or hear gas escaping,
immediately get away from the LP
cylinder/appliance and call your fire department.
LP cylinder valve must have:
• Type 1 outlet compatible with regulator.
• Safety relief valve.
• UL listed Overfill Protection Device (OPD).
This OPD safety feature is identified by a
unique triangular hand wheel. Use only
cylinders equipped with this type of valve.
LP Cylinder Removal, Transport and Storage
•
Turn OFF control knob and LP cylinder valve. Turn
coupling nut counterclockwise by hand only - do not
use tools to disconnect. Install safety cap onto LP
cylinder valve. Always use cap and strap supplied
with valve. Failure to use safety cap as directed
may result in serious personal injury and/or
property damage.
•
LP cylinder must be arranged for vapor withdrawal and
include collar to protect LP cylinder valve.
LP (Liquefied Petroleum Gas)
•
LP gas is nontoxic, odorless and colorless when
produced. For your safety, LP gas has been given an
odor (similar to rotten cabbage) so that it can be
smelled.
•
LP gas is highly flammable and may ignite
unexpectedly when mixed with air.
Safety
Cap
LP Cylinder
Valve
Retainer
Strap
LP Cylinder Filling
•
•
•
Use only licensed and experienced dealers.
•
A disconnected LP cylinder in storage or being
transported must have a safety cap installed (as
shown). Do not store an LP cylinder in enclosed
spaces such as a carport, garage, porch, covered
patio or other building. Never leave an LP cylinder
inside a vehicle which may become overheated by
the sun.
LP dealer must purge cylinder before filling.
Dealer should NEVER fill LP cylinder more than 80% of
LP cylinder volume. Volume of propane in cylinder will
vary by temperature.
•
•
•
Do not store LP cylinder in an area where children
play.
Always keep new and exchanged LP cylinders in
upright position during use, transit or storage.
Storage of appliance indoors is permissible only if the
cylinder is disconnected and removed from the
appliance.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
•
A frosty regulator indicates gas overfill. Immediately
close LP cylinder valve and call local LP gas dealer
for assistance.
WARNING
If “growing” bubbles appear do not use or
move the LP cylinder. Contact an LP gas
supplier or your fire department!
•
•
Do not release liquid propane (LP) gas into the
atmosphere. This is a hazardous practice.
To remove gas from LP cylinder, contact an LP dealer
or call a local fire department for assistance. Check
the telephone directory under “Gas Companies” for
nearest certified LP dealers.
Connecting Regulator To The LP Cylinder
1. LP cylinder must be properly secured onto appliance.
2. Turn control knob to OFF position.
3. Turn LP cylinder OFF by turning hand-wheel
clockwise to a full stop.
LP Cylinder Exchange
•
4. Remove protective cap from LP cylinder valve. Always
use cap and strap supplied with valve.
Many retailers that sell grills offer you the option of
replacing your empty LP cylinder through an
exchange service. Use only those reputable
exchange companies that inspect, precision fill, test
and certify their cylinders. Exchange your cylinder
only for an OPD safety feature-equipped cylinder
as described in the “LP Cylinder” section of this
manual.
c
o k
l
C
OPD Hand Wheel
Safety Relief
Valve
Type 1 outlet with
thread on outside
•
•
Always keep new and exchanged LP cylinders in
upright position during use, transit or storage.
Strap and Cap
Leak test new and exchanged LP cylinders
BEFORE connecting to appliance.
Do not use a POL transport plug (A)
(plastic part with external threads)! It
will defeat the safety feature of the
valve.
A
LP Cylinder Leak Test
For your safety
•
Leak test must be repeated each time LP cylinder is
exchanged or refilled.
5. Hold regulator, insert nipple (B) into LP cylinder valve.
Hand tighten coupling nut, holding regulator in a
straight line (C) with LP cylinder valve so as not to
cross thread the connection.
•
•
•
Do not smoke during leak test.
Do not use an open flame to check for gas leaks.
Appliance must be leak checked outdoors in a well
ventilated area, away from ignition sources such as
gas fired or electrical appliances. During leak test,
keep appliance away from open flames or sparks.
Nipple has to be centered
into the LP cylinder valve.
B
Use a clean paint brush and 50/50 soap and water
solution. Use mild soap and water. s Do not use
Household cleaning agents. Damage to gas train
components can result.
Brush soapy solution onto the shaded areas.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Leak Testing Valve, Hose and Regulator
1. Turn control knob to OFF.
Straight
Hold coupling nut and regulator
as shown for proper connection
to LP cylinder valve.
2. Be sure regulator is tightly connected to LP cylinder.
3. Completely open LP cylinder valve by turning hand
wheel counter clockwise. If you hear a rushing sound,
turn gas off immediately. There is a major leak at the
connection. Correct before proceeding.
4. Brush soapy solution on areas where bubbles are
shown.
C
6. Turn the coupling nut clockwise to tighten to a full
solid stop. The regulator will seal on the back-check
feature in LP cylinder valve, resulting in some
resistance. An additional one-half to three
quarters turn is required to complete connection.
Tighten by hand only - do not use tools.
NOTE:
If you cannot complete connection, disconnect
regulator and repeat steps 5 and 6. If you are still
unable to complete the connection, do not use this
Regulator!
5. “If growing” bubbles appear, there is a leak. Close
LP cylinder valve immediately and re-tighten
connections. If leaks cannot be stopped “do not try
to repair”. Call for replacement parts. Order new
parts by giving the part number from the parts list to
the Service Center at 1-800-232-3398.
6. Always close LP cylinder valve after performing leak
test by turning hand wheel clockwise.
WARNING
• Do not insert any foreign objects into the
valve outlet. You may damage the valve
and cause a leak. Leaking propane may
result in explosion, fire, severe personal
injury or death.
Safety Tips
s Before opening LP cylinder valve, check the coupling
nut for tightness.
s When appliance is not in use, turn off control knob
and LP cylinder valve.
• Never attempt to attach this appliance to
the self-contained LP gas system of a
camper trailer or motor home.
s Never move appliance while in operation or still hot.
s The regulator may make a humming or whistling
noise during operation. This will not affect safety or
use of fireplace.
s Check appliance before each use for buildup of
any leaves or other material that will burn or block
the burner ports. Clean when needed before
using. Have appliance inspected annually by a
qualified service person.
WARNING
• Do not use appliance until leak checked.
• If leak is detected at any time, STOP and
call your fire department.
• If you cannot stop a gas leak, immediately
close LP cylinder valve and call a LP gas
supplier or your fire department!
6
Download from Www.Somanuals.com. All Manuals Search And Download.
CAUTION
WARNING
For Safe Use of Your Outdoor Stove Top and to
Avoid Serious Injury:
If burner does not light turn knob to OFF, wait 5
minutes, try again. If the burner does not ignite with
valve open, gas will continue to flow out of the burner
and could accidentally ignite with risk of injury.
• Do not let children operate or play near appliance.
• Keep appliance area clear and free from materials that
burn.
Match Lighting
• Do not block holes in sides or back of appliance.
• Check burner flames regularly.
Do not lean over appliance while lighting. Use a large
kitchen match or fireplace match to light the
appliance.
1. Place a lit match to burner.
2. Press and turn control knob
To HI.
• Use appliance only in a well-ventilated space. NEVER
use in enclosed space such as carport, garage, porch,
covered patio, or under an overhead structure of any
kind.
• Do not use charcoal or ceramic briquets in a gas
appliance. (Unless briquets are supplied with your
appliance.)
Burner Flame Check
• Light burner, rotate knob
from HI to LOW. You
should see a smaller
flame in LOW position
HI
• Use appliance at least 3 ft.
from any wall or surface.
Maintain 10 ft. clearance to
objects that can catch fire or
sources of ignition such as
pilot lights on water heaters,
live electrical appliances, etc..
LOW
than seen on HI. Always check flame prior to each use.
Burner Check
• Inspect burner prior to each use. If burner is damaged
do not use. Call manufacturer at 1-800-232-3398 to
obtain a replacement.
• Apartment Dwellers:
Check with management to learn the requirements
and fire codes for using an LP gas appliance in your
apartment complex. If allowed, use outside on the
ground floor with a three (3) foot clearance from walls
or rails. Do not use on or under balconies.
Turning Appliance Off
• Turn knob to OFF position. Turn LP cylinder OFF by
turning handwheel clockwise to a full stop.
• NEVER attempt to light burner with lid closed. A
buildup of non-ignited gas inside a closed
appliance is hazardous.
Ignitor Check
• Turn gas OFF at LP cylinder. Turn ignitor knob rapidly.
“Click” should be heard and spark seen each time
between burner and electrode. See “Troubleshooting” if
no click or spark.
• Never operate appliance with LP cylinder out of
correct position specified in assembly
instructions.
• Always close LP cylinder valve and remove
coupling nut before moving LP cylinder from
specified operation position.
Valve Check
• Important: Make sure gas is OFF at LP cylinder before
checking valves. Knob locks in OFF position. To check
valve, first push in knob and release, knob should
spring back. If knob does not spring back, replace valve
assembly before using appliance. Turn knob to MED
position then turn back to OFF position. Valve should
turn smoothly.
Ignitor Lighting
1. Open lid during lighting.
2. Press and turn the control knob to the HI position.
3. Turn ROTARY IGNITOR knob rapidly.
4. If ignition does not occur in 5 seconds, turn the burner
control knob OFF, wait 5 minutes, and repeat lighting
procedure. If ignition still does not occur, follow “Match
Lighting” instructions.
Hose Check
• Before each use, check to see if hose is cut or worn.
Replace damaged hose before using appliance. Use
only hose/valve/regulator specified by manufacturer.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
General Cleaning
CAUTION
Natural Hazard • Spiders
• Do not mistake brown or black accumulation of grease and
smoke for paint. Interiors of gas appliances are not painted
at the factory (and should never be painted). Apply a strong
solution of detergent and water or use a grill cleaner with
scrub brush on insides of lid and bottom. Rinse and allow to
completely air dry. Do not apply a caustic grill/oven
cleaner to painted surfaces.
FACT: Sometimes spiders and other
small insects climb into the burner tube.
The spiders spin webs, build nests and
lay eggs. The webs or nests can be very
small, but they are very strong and can
block the flow of gas. Clean burner prior to
use after storing, or after a period of one
Month not being used.
• Plastic parts: Wash with warm soapy water and wipe dry.
s Do not use citrisol, abrasive cleaners, degreasers or a
concentrated grill cleaner on plastic parts. Damage to and
failure of parts can result.
• Porcelain surfaces: Because of glass-like composition, most
residue can be wiped away with baking soda/water solution
or specially formulated cleaner. Use nonabrasive scouring
powder for stubborn stains.
Typical spider webs inside burner
• Painted surfaces: Wash with mild detergent or nonabrasive
cleaner and warm soapy water. Wipe dry with a soft
nonabrasive cloth.
An obstruction can result in a “flashback” (a fire in the
burner tube). The appliance may still light, but the
obstruction does not allow full gas flow to the burner.
If you experience the following:
• Stainless steel surfaces: To maintain your appliance’s high
quality appearance, wash with mild detergent and warm
soapy water and wipe dry with a soft cloth after each use.
Baked-on grease deposits may require the use of an abrasive
plastic cleaning pad. Use only in direction of brushed finish to
avoid damage. Do not use abrasive pad on areas with
graphics.
1. Smell gas.
2. Burner will not light.
3. Fire coming from around or behind control knob.
STOP! Immediately turn off gas at LP
cylinder.
• Cooking grate: Coating the cooking grate with spray-on
cooking oil will keep the food from sticking and make clean
up easier. After cooking, scrape the grates with a long
handled, brass wire bristle brush.
SOLUTION: Wait for appliance to cool.
Clean burner often. Spiders and insects
don’t care if your appliance is brand new
or you just cleaned it. Use a hose with a
nozzle attached. Forced water will wash
out the web.
CAUTION
For residential use only. Do not use for commercial
cooking.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
CARE AND CLEANING OF STAINLESS STEEL
Extreme temperatures from charcoal or wood fires will cause discoloration of stainless steel surfaces. Routine cleaning is necessary
to preserve the appearance and corrosion resistance of Stainless Steel. The methods below are suggestions for cleaning stainless
steel surfaces. Choose a cleaning method appropriate to the requirement. If you choose to use scouring powder or solvents, consult
with the solvent manufacturer or supplier before use.
Before cleaning, first test any cleaning product in an inconspicuous location and consider the possibility of scratching and the
potential for corrosion caused by not completely removing cleaners. Never use brushes or steel wool as they will scratch and leave
particles embedded on stainless steel surfaces, which can lead to rusting. Always rub or wipe in the direction of the polish lines in
the stainless steel surface, not across them. Thorough rinsing with clean water is recommended after all cleaning procedures. Dry
all surfaces completely after rinsing. Be careful not to let any stainless steel cleaner come in contact with painted or plastic
components as damage may occur.
Routine Care
The Char-Broil® Stainless Steel Grill Cleaner and the Thermos® Stainless Steel Grill Cleaner are good choices for routine cleaning
of stainless steel surfaces. Mild stains and loose dirt and soil can also be removed with a soft cloth and clean warm water. Rinse
with clean water and wipe dry.
Stubborn Stains
Stubborn stains, discoloration and possibly rust and rust pitting can occur from cooking, exposure to harsh outdoor conditions, or
extreme cooking temperatures. There are many cleaning agents commercially available formulated to restore the finish of stainless
steel. Obtain advice from the solvent manufacturer or supplier when choosing the appropriate cleaner for your requirement. These
cleaners can be acidic. Care should be taken to avoid contact with eyes or mouth. Be careful not let any powder or solvent come in
contact with painted or plastic components as damage may occur.
The chart below has been reproduced with permission from the Specialty Steel Institute of North America. For additional details
Job
Cleaning Agents*
Comments
Routine Cleaning
Warm Water, Soap, Ammonia, Detergent
Apply with sponge or soft cloth.
Can be used on all finishes.
Fingerprints and Smears 3M Stainless Steel Cleaner and Polish, Arcal 20, Lac-O-Nu,
Lumin Wash, O’Cedar Cream Polish, Stainless Shine
Provides barrier film to minimize
fingerprints. Can be used on all finishes.
Stubborn Stains
and Discoloration
3M Stainless Steel Cleaner and Polish, All chem Concentrated Rub lightly, using dry damp cloth, in
Cleaner, Samae, Twinkle, Cameo Copper Cleaner, Grade FFF
or Grade F Italian Pumice, Whiting or Talc, Liquid Nu Steel,
Copper’s or Revere Stainless Steel Cleaner, Household
Cleaners, Lumin Cleaner, Zud Restoro, Sta-Clean, Highlite,
Allen Polish, Penny-Brite, Copper-Brite
the direction of polish lines on the
stainless steel.
Grease and Blood
Burnt-on or
Baked-on Foods
Scotch-Brite Power Pad 2001, Easy-Off, De-Grease-It, 4% to
6% hot solution of such agents as tri-sodium polyphosphate,
5% to 15% caustic soda solution
Excellent removal on acids, all finishes.
Particularly useful where rubbing
is not practical.
Grease and Oil
Any good commercial detergent or caustic cleanser.
Apply with sponge or soft cloth in
direction of polish lines.
*NOTE: Use of proprietary names is intended only to indicate a type of cleaner and does not constitute an endorsement. Omission of
any proprietary cleanser does not imply its inadequacy. All products should be used in strict accordance with instructions on package.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Problem
Possible Cause
Prevention/Cure
Burner will not light
using ignitor.
— Electrode and burner are wet.
— Electrode is cracked or broken, — Replace electrode.
“sparks at crack”.
— Wipe dry with cloth.
— Wire is loose or disconnected.
— Wire is shorting (sparking)
between ignitor and electrode.
— Bad ignitor.
— Reconnect or replace ignitor wire.
— Replace ignitor wire.
— Replace ignitor.
Burner will not match- — No gas flow.
light.
— Check to see if LP cylinder is empty. If LP cylinder is
not empty, refer to “Sudden drop in gas flow”.
— Turn the coupling nut about one-half to three quarters
additional turn until solid stop. Tighten by hand only—
do not use tools.
— Coupling nut and regulator not
fully connected.
— Obstruction of gas flow.
— Disengagement of burner to
valve.
— Clear burner tube.
— Re-engage burner and valve.
— Is appliance assembled
correctly?
— Check assembly instruction steps.
Sudden drop in gas
flow or low flame.
— Out of gas.
— Excess flow valve tripped.
— Check for gas in LP cylinder.
— Turn off knob, wait 30 seconds and light appliance. If
flames are still low, turn off knob and LP cylinder
valve. Disconnect regulator. Reconnect regulator and
leak check. Turn on LP cylinder valve, wait 30
seconds and then light appliance.
Flames blow out.
— High or gusting winds.
— Low on LP gas
— Excess flow valve tripped.
— Increase flame height.
— Refill LP cylinder.
— Refer to “Sudden drop in gas flow” above.
Flashback... (fire in
burner tube).
— Burner is blocked.
— Turn knob to OFF and clean burner.
— The worn nozzles don’t have enough “bite” to engage
the valve. Try a second LP dealer.
Unable to fill LP
cylinder
— Some dealers have older fill
nozzles with worn threads.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts List
Key Qty.
Description
Part No.
A. . . . . . 1 . . . . Cover Assembly. . . . . . . . . . . . . . . . . . . . . 29100873
B. . . . . . 1 . . . . Cast Iron Grate . . . . . . . . . . . . . . . . . . . . . 29100874
C. . . . . . 1 . . . . Burner Assembly Kit. . . . . . . . . . . . . . . . . . 55700664
D. . . . . . 1 . . . . Hose/Valve/Regulator Kit. . . . . . . . . . . . . . 55700665
E. . . . . . 1 . . . . Ignitor Kit . . . . . . . . . . . . . . . . . . . . . . . . . . 55700666
F. . . . . . 1 . . . . Towel Bar Kit . . . . . . . . . . . . . . . . . . . . . . . 55700667
G . . . . . 1 . . . . Stainless Steel Top Kit . . . . . . . . . . . . . . . . 55700668
H. . . . . . 1 . . . . Heat Shield Kit. . . . . . . . . . . . . . . . . . . . . . 55700669
I . . . . . . 1 . . . . Wrap (Body) Kit . . . . . . . . . . . . . . . . . . . . . 55700670
J . . . . . . 1 . . . . Control Panel Kit . . . . . . . . . . . . . . . . . . . . 55700671
K. . . . . . 1 . . . . Base Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . 55700672
L . . . . . . 1 . . . . Caster Kit (Locking) . . . . . . . . . . . . . . . . . . 55700673
M . . . . . 1 . . . . Caster Kit (Non-Locking) . . . . . . . . . . . . . . 55700674
N. . . . . . 1 . . . . Rotary Ignition Knob . . . . . . . . . . . . . . . . . 29000950
O . . . . . 1 . . . . Control Knob . . . . . . . . . . . . . . . . . . . . . . . 29000951
1 . . . . Hardware Bag . . . . . . . . . . . . . . . . . . . . . . 42000138
1 . . . . Assembly Instructions . . . . . . . . . . . . . . . . 42804116
Tools required for assembly: Phillips screwdriver (not provided) • Adjustable wrench (not provided)
Estimated assembly time: 30 – 45 minutes
STOP!
Missing a part?
No need to go back to the store!
Call Our Help Line
The store where you made your purchase
does not stock parts for this item. If you
need parts, whether they are missing or
damaged, call the Customer Service toll
free Help Line.
Call us and we will gladly ship
the part you need
FREE OF CHARGE.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts Diagram
A
B
G
H
C
F
F
J
F
E
D
O
N
C
I
K
L
L
M
M
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Step 1
Slide tool hooks onto one of the towel bars prior to assembly.
Attach each towel bar using two 1/4-20x3/4” machine screws.
1/4-20x3/4”
Machine Screw
DO NOT LIFT UNIT USING TOWEL BARS.
1/4-20x3/4”
Machine Screw
Qty: 4
Tool hook
Towel bar
55700667
Wrap/Body
55700670
Step 2
Feed burner tube through center hole of heat shield. Align the three threaded studs on bottom of burner
with small holes in heat shield. Make sure electrode passes through electrode hole. Secure burner
beneath heat shield using three #10-24 hex/keps nuts. Attach ignitor wire to electrode.
#10-24
Hex/Keps Nut
Qty: 3
Burner assembly
55700664
Electrode
#10-24 Hex/Keps Nut
Ignitor Wire
55700664
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 3
Position rotary ignitor as shown below. Attach ignitor behind
control panel using two #8x1/2” self-tap screws.
#8x1/2”
Self-Tap Screw
Qty: 2
Rotary ignitor
55700666
Control panel
55700671
#8x1/2” Self-Tap Screw
Step 4
Insert valve/hose through front
opening and attach to control
panel using two #8-32x3/8”
machine screws.
#8-32x3/8”
Machine Screw
Qty: 2
NOTE: Screws may already be
installed in valve and must be
removed to attach valve to
control panel.
Hose/Valve/Regulator assembly
55700665
#8-32x3/8”
Machine Screw
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 5
Align valve with burner tube. See Figure A for proper valve-to-burner
engagement. Secure control panel to body at each end using two #10-
24x3/8” machine screws and two #10-24 hex/keps nuts. Inside body,
insert one #10x1/2” self-tap screw through body into panel. It is helpful to
have someone hold panel in position while attaching hardware.
#10x1/2”
Self-Tap Screw Machine Screw Hex/Keps Nut
#10-24x3/8”
#10-24
Qty: 1
Qty: 2
Qty: 2
#10-24
Hex/Keps Nut
inside body.
Figure A
#10-24x3/8”
Machine Screw
#10x1/2”
Self-Tap Screw
from inside body
Burner
Tube
Beneath control panel
#10-24x3/8”
Machine Screw
from inside body
#10-24
Hex/Keps Nut
Step 6
Feed ignitor wire from electrode through opening beneath control panel and
attach to ignitor. Press rotary ignitor knob (smaller knob) onto ignitor stem
and control knob onto valve stem.
Beneath control panel
Rotary
ignitor knob
29000950
Control
knob
29000951
Ignitor wire
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 7
Lift body assembly and place onto
base. Back/open-end of body
#10-24x1/2”
Machine Screw
#10-24x1/2”
Machine Screw
Qty: 9
assembly should face back of base.
Back of base has locking casters,
front has non-locking casters. Attach
body assembly to base using nine
#10-24x1/2” machine screws and
nine #10-24 hex/keps nuts.
#10-24
Hex/Keps Nut
Qty: 9
Base
55700672
Locking
caster
55700673
#10-24
Hex/Keps Nut
Locking
caster
55700673
Step 8
Place cast iron grate onto top. Align grate
legs with slots in top.
Cast iron grate
29100874
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 9
Place cover assembly onto top. Align lower hinge
holes with holes on back side of top. Secure using
two #8x1/2” self-tap screws.
Cover assembly
29100873
#8x1/2”
Self-Tap Screw
Qty: 2
#8x1/2”
Self-Tap Screw
Step 10
LP GAS CYLINDER IS SOLD SEPARATELY. Fill and
leak check the cylinder before attaching to Outdoor Stove
Top and regulator (see Use & Care section). Once
cylinder has been filled and leak checked, place cylinder
into cylinder hole in base. Make sure cylinder valve is
facing to the rear. Secure cylinder with cylinder screw
under base.
Read “Connecting Regulator to the LP Cylinder” in
the Use and Care section of this manual.
See Use & Care section of this manual to perform the
“Burner Flame Check” and for important safety
instructions before using.
Always keep LP cylinders in upright position
during use, transit or storage.
LP gas cylinder
(not included)
CAUTION
Cylinder valve must face to rear of cart once
cylinder is attached. Failure to install cylinder
correctly may allow gas hose to be damaged in
operation, resulting in the risk of fire.
Cylinder screw
17
Download from Www.Somanuals.com. All Manuals Search And Download.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Please register your product online at:
WWW.GRILLREGISTRATION.COM
(If you register online, you do not need to send in this registration card.)
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Char-Broil, LLC • Columbus, GA 31902 • Assembly Instructions © 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
|