Casio Watch WV200A1AV User Manual

MA0810-EA  
Operation Guide 3140  
Getting Acquainted  
Congratulations upon your selection of this CASIO watch. To get the most out of your  
purchase, be sure to read this manual carefully.  
This watch does not have a time zone that corresponds to the UTC offset of  
3.5 hours. Because of this, the radio-controlled timekeeping and World Time  
functions will not display the correct time for Newfoundland, Canada.  
Caution!  
Your watch is shipped with its Auto Display feature (which continually changes the  
contents of the digital display) turned on. Calibration signal reception is disabled while  
Auto Display is turned on.  
Press any button to turn off Auto Display and return to the Timekeeping Mode.  
About This Manual  
Button operations are indicated using the letters shown  
in the illustration.  
Each section of this manual provides you with the  
information you need in order to perform operations in  
each mode. Further details and technical information  
can be found in the “Reference” section.  
General Guide  
Press  
to change from mode to mode.  
C
In any mode (except when a setting screen is on the display), press  
to illuminate  
B
the display.  
Timekeeping Mode  
World Time Mode  
Countdown  
Timer Mode  
Stopwatch Mode  
Alarm Mode  
Press  
.
Important!  
Radio-controlled Atomic Timekeeping  
Normally, your watch should show the correct time as soon as you select your Home  
City code. If it does not, it should adjust automatically after the next auto receive  
operation (in the middle of the night). You can also perform manual receive or you  
can set the time manually.  
The watch will receive the time calibration signal automatically from the applicable  
transmitter (in the middle of the night) and update its settings accordingly. For  
information about the relationship between city codes and transmitters, see Home  
City Codes and Transmitters.  
This watch receives a time calibration signal and updates  
its time setting accordingly.  
Supported time calibration signals: United States (Fort  
Collins), England (Anthorn).  
See the information under “Signal Reception  
Troubleshooting” if you experience problems with time  
calibration signal reception.  
Month – Day  
Day of week  
Year  
Current Time Setting  
Under factory default settings, auto receive is turned off for all of the following city  
codes: HNL (Honolulu), ANC (Anchorage), ATH (Athens), and MOW (Moscow). For  
details about turning on auto receive for these city codes, see To turn auto receive  
on and off.  
You can disable time signal reception, if you want. See To turn auto receive on and  
offfor more information.  
This watch adjusts its time setting automatically in  
accordance with a time calibration signal. You can also  
perform a manual procedure to set the time and date,  
when necessary.  
DST  
indicator  
PM indicator  
Home Time  
The first thing you should do after purchasing this  
watch is to specify your Home City (the city where you  
normally will use the watch). For more information,  
see “To specify your Home City”.  
See the maps under Approximate Reception Rangesfor information about the  
reception ranges of the watch.  
(Hour : Minutes Seconds)  
If you are in an area that does not use Daylight Saving Time (summertime), turn off  
the DST setting.  
When using the watch outside the areas covered by the time signal transmitters, you  
will have to adjust the current time setting manually as required. See Timekeeping”  
for more information about manual time settings.  
The U.S. time calibration signal can be picked up by the watch while in North  
America. The term North Americain this manual refers to the area that consists of  
Canada, the continental United States, and Mexico.  
Time Calibration Signal Reception  
There are two different methods you can use to receive the time calibration signal:  
auto receive and manual receive.  
Auto Receive  
With auto receive, the watch receives the time calibration signal automatically up to  
six times a day. When any auto receive is successful, the remaining auto receive  
operations are not performed. For more information, see About Auto Receive.  
To specify your Home City  
1. In the Timekeeping Mode, hold down  
until the city  
A
City code  
code starts to flash, which indicates the setting screen.  
Manual Receive  
2. Press  
(east) and  
D
(west) to select the city code you  
B
Manual receive lets you start a time calibration receive operation with the press of a  
button. For more information, see To perform manual receive.  
want to use as your Home City.  
Time calibration signal reception is supported when  
any one of the city codes shown in the table below is  
selected as your Home City.  
U.S. Signal  
U.K. Signal  
City City  
Code Name  
City City  
Code Name  
City  
Code  
City  
Name  
City City  
Code Name  
HNL Honolulu  
YWG Winnipeg  
LIS  
Lisbon  
London  
Madrid  
Paris  
ATH Athens  
MOW Moscow  
ANC Anchorage CHI Chicago  
YVR Vancouver MIA Miami  
LAX Los Angeles YTO Toronto  
YEA Edmonton  
DEN Denver  
LON  
MAD  
PAR  
ROM  
BER  
STO  
NYC New York  
YHZ Halifax  
Rome  
Berlin  
MEX Mexico City YYT St. Johns  
Stockholm  
3. Press twice to exit the setting screen.  
A
1
Download from Www.Somanuals.com. All Manuals Search And Download.  
Operation Guide 3140  
Signal Reception Troubleshooting  
Check the following points whenever you experience problems with calibration signal  
reception.  
Stopwatch  
The stopwatch lets you measure elapsed time, split times,  
and two nishes.  
Timekeeping Mode time  
(Hour : Minutes Seconds)  
Problem  
Probable Cause  
What you should do  
The display range of the stopwatch is 59 minutes, 59.99  
Cannot perform The watch is not in the Timekeeping Mode. Enter the Timekeeping Mode  
seconds.  
manual receive. Your current Home City is not one of the  
following city codes:  
and try again.  
The stopwatch continues to run, restarting from zero  
after it reaches its limit, until you stop it.  
Exiting the Stopwatch Mode while a split time is frozen  
on the display clears the split time and returns to  
elapsed time measurement.  
The stopwatch measurement operation continues even  
if you exit the Stopwatch Mode.  
Select one of the cities to the  
left as your Home City.  
HNL, ANC, YVR, LAX, YEA, DEN, MEX,  
YWG, CHI, MIA, YTO, NYC, YHZ, YYT, LIS, Stop the countdown timer  
LON, MAD, PAR, ROM, BER, STO, ATH, or and try again.  
MOW.  
Minutes  
The countdown timer is running.  
Seconds  
All of the operations in this section are performed in the  
Auto receive is  
You changed the time setting manually.  
Perform manual signal  
receive or wait until the next  
auto signal receive operation  
is performed.  
1/100 second  
Stopwatch Mode, which you enter by pressing  
.
C
turned on, but the The watch was not in the Timekeeping or  
Level 3 receiving  
indicator does  
World Time Mode, or you performed some  
button operation during the auto receive  
To measure times with the stopwatch  
not appear on the operation.  
Perform manual signal  
receive or wait until the next  
auto signal receive operation  
is performed.  
Elapsed Time  
display.  
Even if receive is successful, the Level 3  
receiving indicator disappears every day  
when the rst auto receive operation of the  
day is performed.  
Start  
Stop  
Re-start  
Stop  
Stop  
Clear  
Clear  
Check to make sure the  
Split Time  
Time data (hour, minutes, seconds) only was watch is in a location where  
received during the last receive operation.  
The Level 3 receiving indicator appears only  
when time data and date data (year, month,  
day) are both received.  
it can receive the signal.  
Split  
Split release  
Start  
(SPL displayed)  
Two Finishes  
Time setting is  
incorrect  
If the time is one hour off, the DST setting  
may be incorrect.  
Change the DST setting to  
Auto DST.  
Split  
Stop  
Split release  
Clear  
Start  
following signal The Home City code setting is not correct for Select the correct Home City  
reception. the area where you are using the watch. code.  
First runner  
Second runner  
finishes.  
Display time of  
second runner.  
finishes.  
Display time of  
first runner.  
For further information, see Important!and Radio-controlled Atomic Timekeeping  
Precautions.  
Alarm  
After you set (and turn on) the daily alarm, the alarm tone  
sounds when the alarm time is reached. You can also turn  
on an Hourly Time Signal that causes the watch to beep  
for about one second every hour on the hour.  
Timekeeping Mode time  
(Hour : Minutes Seconds)  
World Time  
Alarm on indicator  
City code  
The World Time Mode shows you the current time in 48  
cities (29 time zones) around the world.  
If the current time shown for a city is wrong, check  
your Home City time settings and make the necessary  
changes.  
All of the operations in this section are performed in the  
Alarm Mode, which you enter by pressing  
.
C
UTC offset  
All of the operations in this section are performed in the  
World Time Mode, which you enter by pressing  
.
C
Alarm time  
To view the time in another city  
(Hour : Minutes)  
While in the World Time Mode, press  
to scroll  
D
Hourly time signal on  
indicator  
Current time in  
selected city  
eastward through the city codes (time zones).  
For full information on city codes, see the City Code  
Table.  
Timekeeping Mode time  
To set the alarm time  
1. In the Alarm Mode, hold down  
until the hour setting  
A
To toggle a city code time between Standard Time and Daylight Saving Time  
of the alarm time starts to ash, which indicates the  
1. In the World Time Mode, use  
to display the city code  
D
DST indicator  
setting screen.  
(time zone) whose Standard Time/Daylight Saving Time  
This automatically turns on the alarm.  
setting you want to change.  
2. Press  
to move the ashing between the hour and  
C
2. Hold down  
to toggle Daylight Saving Time (DST  
A
minute settings.  
indicator displayed) and Standard Time (DST indicator  
not displayed).  
The DST indicator will appear whenever you display a  
city code for which Daylight Saving Time is turned on.  
Note that the DST/Standard Time setting affects only the  
currently displayed city code. Other city codes are not  
affected.  
3. While a setting is ashing, use (+) and  
() to change it.  
D
B
When setting the alarm time using the 12-hour format, take care to set the time  
correctly as a.m. (no indicator) or p.m. (P indicator).  
4. Press  
to exit the setting screen.  
A
Alarm Operation  
The alarm sounds at the preset time for about 10 seconds (in all modes), or until you  
stop it by pressing any button.  
Countdown Timer  
To test the alarm  
In the Alarm Mode, hold down  
You can set the countdown timer within a range of one  
to 60 minutes. An alarm sounds when the countdown  
reaches zero.  
Timekeeping Mode time  
(Hour : Minutes Seconds)  
to sound the alarm.  
D
To turn the daily alarm and the Hourly Time Signal on and off  
In the Alarm Mode, press to cycle through the settings shown below.  
All of the operations in this section are performed in the  
Countdown Timer Mode, which you enter by pressing  
D
.
C
Alarm On Indicator / Hourly Time Signal On Indicator  
To set the countdown start time  
1. While the countdown start time is on the display in the  
Countdown Timer Mode, hold down  
until the current  
A
Alarm Off  
Signal Off  
Alarm On  
Signal Off  
Alarm Off  
Signal On  
Alarm On  
Signal On  
Minutes Seconds  
countdown start time starts to ash, which indicates the  
setting screen.  
If the countdown start time is not displayed, use the procedure under To use the  
countdown timerto display it.  
The alarm on indicator and the Hourly Time Signal on indicator are shown on the  
display in all modes while these functions are turned on.  
2. While a setting is ashing, use  
(+) and  
() to change it.  
D
B
3. Press  
to exit the setting screen.  
A
To use the countdown timer  
Press while in the Countdown Timer Mode to start the countdown timer.  
D
When the end of the countdown is reached, the alarm sounds for 10 seconds or until  
you stop it by pressing any button. The countdown time is reset automatically to its  
starting value after the alarm stops.  
Press  
while a countdown operation is in progress to pause it. Press  
again to  
D
D
resume the countdown.  
To stop a countdown operation completely, rst pause it (by pressing  
), and then  
D
press  
. This returns the countdown time to its starting value.  
A
Calibration signal reception is disabled while a countdown timer operation is in  
progress.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Operation Guide 3140  
Timekeeping  
Reference  
Use the Timekeeping Mode to set and view the current time and date.  
When setting the time, you can also congure settings for the City Code, the DST  
setting, the 12/24-Hour Format, Year, Month, Day, the Language setting, and the  
Month/Day display format.  
This section contains more detailed and technical information about watch operation.  
It also contains important precautions and notes about the various features and  
functions of this watch.  
Auto Display  
Pressing  
in the Timekeeping Mode will display the Last Signal screen.  
D
Auto Display continually changes the contents of the digital display.  
Current Time and Date Screen  
Day of week  
Month – Day  
Last Signal Screen  
Receive date  
To turn off Auto Display  
Press any button to turn off Auto Display. This returns to the Timekeeping Mode.  
Year  
Press  
.
To turn on Auto Display  
In the Timekeeping Mode, while holding down  
seconds until the watch beeps.  
, hold down  
B
for about two  
D
Note  
Calibration signal reception is disabled while Auto Display is being performed.  
Auto Display cannot be performed while a setting screen is on the display.  
PM indicator  
DST indicator  
Home Time  
(Hour : Minutes Seconds)  
Receive time  
Button Operation Tone  
Note  
The button operation tone sounds any time you press one  
of the watchs buttons. You can turn the button operation  
tone on or off as desired.  
Even if you turn off the button operation tone, the alarm,  
Hourly Time Signal, and Countdown Timer Mode alarm  
all operate normally.  
This watch is capable of displaying text for the day of the week in any one of  
nine different languages (English, Spanish, French, Portuguese, German, Italian,  
Chinese, Russian, and Japanese).  
Setting the Time and Date  
Make sure you select your Home City code before you change the current time  
and date settings. World Time Mode times are all displayed in accordance with the  
Timekeeping Mode settings. Because of this, World Time Mode times will not be  
correct if you do not select the proper Home City code before setting the time and  
date in the Timekeeping Mode.  
To turn the button operation tone on and off  
In any mode (except when a setting screen is on the  
MUTE indicator  
display), hold down  
to toggle the button operation tone  
C
on (MUTE not displayed) and off (MUTE displayed).  
To set the time and date  
Since the  
button is also the mode change button, holding it down to turn the  
C
1. In the Timekeeping Mode, hold down  
until the city  
A
button operation tone on or off also causes the watchs current mode to change.  
The MUTE indicator is displayed in all modes when the button operation tone is  
turned off.  
City code  
code starts to ash, which indicates the setting screen.  
2. Press  
to change the ashing contents in the  
C
sequence shown below to select other settings.  
Auto Return Features  
If you leave the watch with the Last Signal screen in the Timekeeping Mode for one  
or two minutes without performing any operation, it returns to the Current Time and  
Date screen in the Timekeeping Mode automatically.  
If you leave the watch in the Alarm Mode for two or three minutes without performing  
any operation, it returns to the Timekeeping Mode automatically.  
If you leave the watch with a ashing setting on the display for two or three minutes  
without performing any operation, the watch exits the setting screen automatically.  
City  
Code  
12/24-Hour  
Format  
DST  
Seconds  
Hour  
Minutes  
Scrolling  
Month/Day  
Display Format  
Language  
Day  
Month  
Year  
The  
and  
buttons are used in various modes and setting screens to scroll  
B
D
through data. In most cases, holding down these buttons during a scroll operation  
3. When the setting you want to change is ashing, use  
and/or  
to change it as  
B
D
D
scrolls through the data at high speed.  
described below.  
Initial Screens  
Screen:  
To do this:  
Change the city code  
Cycle between auto DST (  
Do this:  
When you enter the World Time or Alarm Mode, the data you were viewing when  
you last exited the mode appears rst.  
Use  
(east) and  
(west).  
B
Radio-controlled Atomic Timekeeping Precautions  
),  
), and Daylight  
Standard Time (  
Saving Time (  
Press  
.
The display of the watch is blank while an auto receive operation is in progress.  
Strong electrostatic charge can result in the wrong time being set.  
The time calibration signal is bounced off the ionosphere. Because of this, such  
factors as changes in the reectivity of the ionosphere, as well as movement of the  
ionosphere to higher altitudes due to seasonal atmospheric changes or the time of  
day may change the reception range of the signal and make reception temporarily  
impossible.  
D
)
Toggle between 12-hour (  
) and  
12H  
Press  
Press  
.
.
D
D
24-hour (  
) timekeeping  
24H  
Reset the seconds to  
Even if the time calibration signal is received properly, certain conditions can cause  
Change the hour, minutes, or year  
the time setting to be off by up to one second.  
Use  
Use  
(+) and  
().  
D
D
B
The current time setting in accordance with the time calibration signal takes priority  
over any time settings you make.  
The watch is designed to update the date and day of the week automatically for  
the period January 1, 2000 to December 31, 2099. Setting of the date by a time  
calibration signal cannot be performed starting from January 1, 2100.  
This watch can receive signals that differentiate between leap years and non-leap  
years.  
Though this watch is designed to receive both time data (hour, minutes, seconds)  
and date data (year, month, day), certain signal conditions can limit reception to time  
data only.  
Normally, the signal reception date shown by the Last Signal screen is the date data  
included in the received time calibration signal. When only time data is received,  
however, the Last Signal screen shows the date as kept in the Timekeeping Mode at  
the time of signal reception.  
If you are in an area where proper time calibration signal reception is impossible, the  
watch keeps time with the precision noted in Specications.  
If you have problems with proper time calibration signal reception or if the time  
setting is wrong after signal reception, check your current city code, DST (summer  
time), and auto receive settings. The following are the initial factory defaults for  
these settings.  
Change the month or day  
Change the language  
ENG: English ESP: Spanish FRA: French  
POR: Portuguese DEU: German  
ITA: Italian CHN: Chinese  
JPN: JapaneseRussian  
and  
.
B
: Russian  
Toggle the month/day display format between  
month/day (M/D) and day/month (D/M).  
Press  
.
D
See the City Code Tablefor a complete list of available city codes.  
See the Day of the Week Listfor information on abbreviations used.  
Auto DST (  
) can be selected only while HNL, ANC, YVR, LAX, YEA,  
DEN, MEX, YWG, CHI, MIA, YTO, NYC, YHZ, YYT, LIS, LON, MAD, PAR,  
ROM, BER, STO, ATH, or MOW is selected as the Home City code. For more  
information, see Daylight Saving Time (DST)below.  
4. Press  
to exit the setting screen.  
A
Daylight Saving Time (DST)  
Setting  
City code  
Initial Factory Default  
Daylight Saving Time (summer time) advances the time setting by one hour from  
Standard Time. Remember that not all countries or even local areas use Daylight  
Saving Time.  
The time calibration signals transmitted from Fort Collins (the United States) or  
Anthorn (England) includes both Standard Time and DST data. When the Auto DST  
setting is turned on, the watch switches between Standard Time and DST (summer  
time) automatically in accordance with the received time signal.  
(New York)  
DST (summer time)  
Auto receive  
(Auto switching)  
(Auto receive)  
Timekeeping  
The default DST setting is Auto DST (  
) whenever you select ANC, YVR,  
Resetting the seconds to 00 while the current count is in the range of 30 to 59  
causes the minutes to be increased by 1. In the range of 00 to 29, the seconds are  
reset to 00 without changing the minutes.  
The day of the week is displayed automatically in accordance with the date (year,  
month, and day) settings.  
LAX, YEA, DEN, MEX, YWG, CHI, MIA, YTO, NYC, YHZ, YYT, LIS, LON, MAD,  
PAR, ROM, BER, STO, ATH, or MOW as your Home City code.  
If you experience problems receiving the time calibration signal in your area, it  
probably is best to switch between Standard Time and Daylight Saving Time (summer  
time) manually.  
The year can be set in the range of 2000 to 2099.  
The watchs built-in full automatic calendar makes allowances for different month  
lengths and leap years. Once you set the date, there should be no reason to change  
it except after you have the watchs battery replaced.  
To change the Daylight Saving Time (summer time) setting  
1. In the Timekeeping Mode, hold down  
until the city code starts to ash, which  
A
indicates the setting screen.  
The times for the Timekeeping Mode and all the city codes of the World Time Mode  
are calculated in accordance with each citys UTC offset.  
2. Press  
and the DST setting screen appears.  
to cycle through the DST settings in the sequence shown below.  
C
3. Use  
D
The UTC offset is a value that indicates the time difference between a reference  
point in Greenwich, England and the time zone where a city is located.  
The letters UTCis the abbreviation for Coordinated Universal Time, which is the  
world-wide scientic standard of timekeeping. It is based upon carefully maintained  
atomic (cesium) clocks that keep time accurately to within microseconds. Leap  
seconds are added or subtracted as necessary to keep UTC in sync with the Earths  
rotation.  
Auto DST  
DST off  
DST on  
(
(
)
(
)
)
4. When the setting you want is selected, press  
to exit the setting screen.  
A
The DST indicator appears to indicate that Daylight Saving Time is turned on.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Operation Guide 3140  
12-hour/24-hour Timekeeping Formats  
The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is also  
applied in all other modes  
.
With the 12-hour format, the PM indicator (P) appears on the display for times in  
the range of noon to 11:59 p.m. and no indicator appears for times in the range of  
midnight to 11:59 a.m.  
With the 24-hour format, times are displayed in the range of 0:00 to 23:59, without  
any indicator.  
Illumination  
This watch has an EL (electro-luminescent) panel that causes the entire display to  
glow for easy reading in the dark. In any mode (except when a setting screen is on the  
display), press  
to illuminate the display for about three seconds  
.
B
Illumination Precautions  
The electro-luminescent panel that provides illumination loses power after very long  
use.  
Illumination may be hard to see when viewed under direct sunlight.  
The watch may emit an audible sound whenever the display is illuminated. This  
is due to vibration of the EL panel used for illumination, and does not indicate  
malfunction.  
Illumination turns off automatically whenever an alarm sounds.  
Frequent use of illumination runs down the battery.  
Day of the Week List  
Sunday Monday Tuesday Wednesday Thursday Friday Saturday  
ENG  
ESP  
FRA  
POR  
DEU  
ITA  
CHN  
SUN  
DOM  
DIM  
DOM  
SON  
DOM  
MON  
LUN  
LUN  
SEG  
MON  
LUN  
TUE  
MAR  
MAR  
TER  
DIE  
MAR  
WED  
MIE  
MER  
QUA  
MIT  
MER  
THU  
JUE  
JEU  
QUI  
DON  
GIO  
FRI  
VIE  
VEN  
SEX  
FRE  
VEN  
SAT  
SAB  
SAM  
SAB  
SAM  
SAB  
JPN  
City Code Table  
City  
City  
UTC  
Other major cities in same time zone  
Code  
PPG  
HNL  
ANC  
YVR  
LAX  
Differential  
–11.0  
Pago Pago  
Honolulu  
Anchorage  
Vancouver  
Los Angeles  
Edmonton  
Denver  
–10.0  
–09.0  
–08.0  
Papeete  
Nome  
San Francisco, Las Vegas,  
Seattle/Tacoma, Dawson City  
El Paso  
YEA  
DEN  
MEX  
YWG  
CHI  
–07.0  
–06.0  
Mexico City  
Winnipeg  
Chicago  
Houston, Dallas/Fort Worth, New Orleans  
MIA  
Miami  
Toronto  
New York  
Caracas  
Halifax  
–05.0  
–04.0  
Montreal, Detroit, Boston,  
Panama City, Havana, Lima, Bogota  
YTO  
NYC  
CCS*  
YHZ  
YYT  
RIO Rio De Janeiro  
RAI  
LIS  
La Paz, Santiago, Port Of Spain  
St. Johns  
–03.5  
–03.0  
–01.0  
+00.0  
Sao Paulo, Buenos Aires, Brasilia, Montevideo  
Dublin, Casablanca, Dakar, Abidjan  
Praia  
Lisbon  
LON  
MAD  
PAR  
ROM  
BER  
STO  
ATH  
CAI  
JRS  
MOW  
JED  
THR  
DXB  
KBL  
KHI  
DEL  
DAC  
RGN  
BKK  
HKG  
BJS  
TPE  
SEL  
TYO  
ADL  
GUM  
SYD  
NOU  
WLG  
London  
Madrid  
Paris  
Rome  
Berlin  
Stockholm  
Athens  
Cairo  
Jerusalem  
Moscow  
Jeddah  
Tehran  
Dubai  
+01.0  
Milan, Amsterdam, Algiers, Hamburg, Frankfurt, Vienna  
+02.0  
+03.0  
Helsinki, Istanbul, Beirut, Damascus,  
Cape Town  
Kuwait, Riyadh, Aden, Addis Ababa, Nairobi  
+03.5  
+04.0  
+04.5  
+05.0  
+05.5  
+06.0  
+06.5  
+07.0  
+08.0  
Shiraz  
Abu Dhabi, Muscat  
Kabul  
Karachi  
Delhi  
Male  
Mumbai, Kolkata, Colombo  
Dhaka  
Yangon  
Bangkok  
Hong Kong  
Beijing  
Taipei  
Jakarta, Phnom Penh, Hanoi, Vientiane  
Singapore, Kuala Lumpur, Manila, Perth, Ulaanbaatar  
Seoul  
Tokyo  
+09.0  
Pyongyang  
Adelaide  
Guam  
Sydney  
Noumea  
Wellington  
+09.5  
+10.0  
Darwin  
Melbourne, Rabaul  
+11.0  
+12.0  
Port Vila  
Christchurch, Nadi, Nauru Island  
Based on data as of June 2007.  
The rules governing global times (GMT differential and UTC offset) and summer time are determined by  
each individual country.  
* In December 2007, Venezuela changed its offset from –4.0 to –4.5. Note, however, that this watch  
displays an offset of –4.0 (the old offset) for the CCS (Caracas, Venezuela) city code.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  

Black Decker Microwave Oven MY26PG User Manual
Bosch Appliances Electric Pressure Cooker 5650 028 820 User Manual
Boss Audio Systems Musical Instrument GT 6B User Manual
Braun Blender MX 2050 R User Manual
Briggs Stratton Air Cleaner 441700 Series User Manual
Broil King Gas Grill 911050 2000 User Manual
Carbine Automobile Accessories PLUS 5900 User Manual
Carrier Heat Pump 50VQP084 300 User Manual
Casio Calculator fx 115ES User Manual
Celestron Computer Monitor 80SLT User Manual