MA0804-EA
Operation Guide 3149
About This Manual
• Button operations are indicated using the letters shown
in the illustration.
• Each section of this manual provides you with the
information you need to perform operations in each
mode. Further details and technical information can be
found in the “Reference” section.
• In any mode, hold down C for about two seconds to return to the Timekeeping
Mode.
General Guide
• Press C to change from mode to mode.
• In any mode, press B to illuminate the display.
Timekeeping Mode
Alarm Mode
Countdown Timer Mode
Stopwatch Mode
Dual Time Mode
Press
.
To set an alarm time
Timekeeping
1. In the Alarm Mode, use D to scroll through the alarm
screens until the one whose time you want to set is
displayed.
Use the Timekeeping Mode to set and view the current
time and date.
Month – Day
Day of week
To set the time and date
1. In the Timekeeping Mode, hold down A until the
seconds start to flash, which indicates the setting
screen.
2. Press C to move the flashing in the sequence shown
below to select other settings.
1
2
• You can configure Alarm as a snooze alarm or a one-time alarm. Alarms
PM indicator
5
Seconds
Day
Hour
Minutes
Year
through can be used as one-time alarms only.
• The snooze alarm repeats every five minutes.
Hour : Minutes Seconds
2. After you select an alarm, hold down A until the hour setting of the alarm time
Month
starts to flash. This indicates the setting screen.
3. When the setting you want to change is flashing, press D to change it as
described below.
3. Press C to move the flashing in the sequence shown
below to select other settings.
To change this setting
Seconds
Perform this button operation
Press D to reset to 00.
Hour
Minutes
Month
Day
Hour, Minutes, Year, Month, Day Press D to increase the setting.
• Pressing D while the seconds are in the range of 30 to 59 resets them to 00 and
adds 1 to the minutes. In the range of 00 to 29, the minutes are unchanged.
4. Press A to exit the setting screen.
• The day of the week is automatically displayed in accordance with the date (year,
month, and day) settings.
4. While a setting is flashing, press D to increase it.
• To set an alarm that does not include a month (Daily alarm, Monthly alarm),
x
x
set for the month. Press D until the mark appears (between 12 and 1) while
month setting is flashing.
• The year can be set in the range of 2000 to 2099.
• To set an alarm that does not include a day (Daily alarm, 1-Month alarm),
xx
xx
mark appears (between the end of the
• The watch’s built-in full automatic calendar automatically makes allowances for
different month lengths and leap years. Once you set the date, there should be no
reason to change it except after you have the watch’s battery replaced.
set
for the day. Press D until the
month and 1) while the day setting is flashing.
• When setting the alarm time using the 12-hour format, take care to set the time
correctly as a.m. or p.m. (P indicator).
To toggle between 12-hour and 24-hour timekeeping
In the Timekeeping Mode, press D to toggle between 12-hour timekeeping and
24-hour timekeeping.
• With the 12-hour format, the P (PM) indicator appears to the left of the hour digits for
times in the range of noon to 11:59 p.m. and no indicator appears to the left of the
hour digits for times in the range of midnight to 11:59 a.m.
• With the 24-hour format, times are displayed in the range of 0:00 to 23:59, without
any indicator.
5. Press A to exit the setting screen.
Alarm Operation
The alarm sounds at the preset time for about 10 seconds. In the case of the snooze
alarm, the alarm operation is performed a total of seven times, every five minutes, or
until you turn the alarm off or change it to a one-time alarm.
Note
• The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is
applied in all other modes.
• Pressing any button stops the alarm tone operation.
• Performing any one of the following operations during a 5-minute interval between
snooze alarms cancels the current snooze alarm operation.
Displaying the Timekeeping Mode setting screen
1
Displaying the Alarm setting screen
Alarms
You can set five independent Daily Alarms. When an
alarm is turned on, the alarm tone sounds when the alarm
time is reached. One of the alarms can be configured as a
snooze alarm or a one-time alarm, while the other four are
one-time alarms.
To test the alarm
In the Alarm Mode, hold down D to sound the alarm.
2
5
To turn Alarms through on and off
1. In the Alarm Mode, use D to select a one-time alarm
One-time alarm on
indicator
2
5
You also can turn on an hourly time signal that causes the
watch to beep twice every hour on the hour.
(alarm number through ).
2. Press A to toggle the displayed alarm on and off.
1
5
2
5
• There are five alarm screens numbered through
.
• Turning on a one-time alarm ( through ) displays the
one-time alarm on indicator on its screen.
• The one-time alarm on indicator is displayed in all
modes.
Hour : Minutes
:00
.
The hourly time signal screen is indicated by
• When you enter the Alarm Mode, the screen you were
viewing when you last exited the mode appears first.
• All of the operations in this section are performed in the
Alarm Mode, which you enter by pressing C.
• If any alarm is on, the one-time alarm on indicator is
shown on the display in all modes.
1
To select the operation of Alarm
Alarm Types
1
1. In the Alarm Mode, use D to select Alarm
2. Press A to cycle through the available settings in the sequence shown below.
.
The alarm type is determined by the settings you make, as described below.
• Daily alarm
Set the hour and minutes for the alarm time. This type of setting causes the alarm to
sound everyday at the time you set.
Snooze alarm on indicator and one-time alarm on indicator
• Date alarm
Set the month, day, hour and minutes for the alarm time. This type of setting causes
the alarm to sound at the specific time, on the specific date you set.
One-time alarm on
Snooze alarm on
Alarm off
• 1-Month alarm
Set the month, hour and minutes for the alarm time. This type of setting causes the
alarm to sound everyday at time you set, only during the month you set.
• The applicable indicator is displayed in all modes when an alarm is turned on.
• The snooze alarm on indicator flashes during the 5-minute intervals between
alarms.
• Monthly alarm
1
• Displaying the Alarm setting screen while the snooze alarm is turned on turns off
Set the day, hour and minutes for the alarm time. This type of setting causes the alarm
to sound every month at time you set, on the day you set.
1
the snooze alarm automatically (making Alarm a one-time alarm).
1
Download from Www.Somanuals.com. All Manuals Search And Download.
|