Casio Time Clock MA0905 EB User Manual

MA0905-EB

Operation Guide 3166

Getting Acquainted

Thank you for purchasing this CASIO product. To ensure that it can provide you with

the years of service for which it is designed, be sure to read this manual carefully and

follow the instructions contained herein.

Note that CASIO COMPUTER CO., LTD. assumes no responsibility for any

damage or loss suffered by you or any third party arising through the use of this

product or its malfunction.

Low Battery Warning

If you use the light or alarms a number of times during

a short period, a R (recover) indicator will ﬂash on the

display and the following operations become disabled as

the battery level recovers.

• Pedometer functions

• Alarm and hourly time signal

• Illumination

Normal operation should return after the battery level

recovers, but if the R indicator appears frequently you

should have the watch’s battery replaced.

��

About This Manual

• Button operations are indicated using the letters shown

in the illustration.

• Each section of this manual provides you with the

information you need to perform operations in each

mode.

General Guide

• Use C to navigate between modes.

•

Holding down

for about three seconds in any mode will return to the Timekeeping Mode.

• Pressing L in any mode will illuminate the display.

��

• Resetting the seconds to 00 while the current count is in the range of 30 to 59

causes the minutes to be increased by 1. In the range of 00 to 29, the seconds are

reset to 00 without changing the minutes.

Setting the Time and Date

Use the following procedure to set the current time and

date after having the watch’s battery replaced, etc. World

Time Mode times will not be displayed correctly unless

you conﬁgure your Home Time settings (the time in the

city where you normally will use the watch) correctly.

• If you to use the watch in Japan, select TYO (Tokyo) as

your Home Time.

��

• Resetting the zero count to zero on an accurate time signal about once a month

helps to ensure accurate timekeeping.

• You can set a date in the range of January 1, 2000 to December 31, 2099.

• The day of the week is set automatically in accordance with the date you set.

•

The watch makes adjustments for leap years and month lengths automatically.

• Summer time, or Daylight Saving Time (DST) as is it is called in some countries,

calls for setting clocks ahead one hour during the summer season. Note that the use

of summer time depends on the country and even the local area.

To set the time and date

1. In the Timekeeping Mode, hold down A for about two

seconds until the seconds digits start to ﬂash. This is

the setting screen.

Stopwatch

��

The Stopwatch Mode lets you measure elapsed time, and record lap/split times.

A sensor built into the watch counts your steps while a stopwatch elapsed time

operation is in progress. The watch uses this information to calculate the energy you

consume, the distance you cover, and your average pace in accordance with personal

information you pre-register.

For each elapsed time operation, the watch creates a record in memory to record the

date, lap/split times, distance covered, energy consumption, number of steps, and

other information.

��

Stopwatch

• Minimum Measuring Unit: 1/100 second

• Maximum Measuring Time: 99:59'59.99''

• Lap/Split Count: 999

��

Elapsed Time Measurement

• Workout Time

• Distance Covered

• Energy Consumption

• Average Pace (*)

2. Use C to move the ﬂashing to the time, date, or Home City setting as shown

above, and then use D (+) and B (−) to change the ﬂashing setting.

• Holding down D or B will change the selected setting at high speed.

• Number of Steps

Setting

To do this:

Do this:

Workout Data (Maximum Cumulative Values)

• Laps/splits: 150

Seconds

Reset to 00

Toggle between standard time (OFF) and

daylight saving time (ON)

Change the Home City setting (See the

“City Code Table”.)

Change the hour or minute setting

Toggle between 12-hour and 24-hour

timekeeping

Change the year, month, or day setting

Press D.

• Cumulative Distance: 999.9 km/621.1 miles

• Cumulative Energy Consumption: 23900.5kcal / 99999.9kJ

• Average Pace: 220 (*)

Summer Time (DST)

Press D.

Use D (east) and

B (west).

Use D (+) and B (–).

Home City

• Cumulative Number of Steps: 999999

• Cumulative Exercise Time: 9999 hours, 59 minutes

• Best Lap

Hour, Minute

* Average Pace

12/24-hour Timekeeping

Year, Month, Day

Press D.

• The average pace value shows your average number of steps per minute while

Use D (+) and B (–).

timing your run with the stopwatch.

• When you take a lap reading, this value shows your average pace during that lap.

• When you take a split reading, this value shows your average pace up to the current

split, starting from the start of your timed run.

3. After all of the settings are the way you want, press A twice to exit the setting

screen.

• The watch also will exit the setting screen automatically if you do not perform any

operation for about two or three minutes.

• When setting the hour, make sure you specify AM (no indicator) or PM (P) correctly,

or that you specify the correct 24-hour time.

Download from Www.Somanuals.com. All Manuals Search And Download.

Operation Guide 3166

To view memory data

Using the Stopwatch

Reading the Stopwatch Display

��

1. In the Timekeeping Mode, press C twice to enter the

Recall Mode.

2. Use D to select the record you want to view.

• Each record has a numbered Title Screen (1 = oldest

record).

��

•

A SENSOR indicator appears on the display while the stopwatch is performing an

elapsed time measurement. This indicator ﬂashes if the watch detect you are running.

3. Use E to scroll through the data (lap/split times, cumulative data, average pace,

Target Attainment Graph

etc.) stored in the currently displayed record.

The target attainment graph shows up to what percentage of the target you achieved.

Also, the watch will beep if you attain your preset target. If you do not have a target

value set, this graph will simply indicate elapsed time. See “To conﬁgure target values

and personal information settings” for information about conﬁguring target values.

��

• The BEST indicator alternating with the lap number indicates that the displayed lap

is the best lap in the current record.

• Pressing D while the Cumulative Energy Consumption or Total Steps screen is

displayed will toggle between the two screens.

To switch the display between lap and split times

Press A to switch the display between the lap time and split time.

4. Pressing B while a Title Screen (RUN) is displayed will switch to the Cumulative

Data Title Screen (ALL). To return to the Title Screen from the Cumulative Data

Title Screen, press B.

��

• Pressing D while the Cumulative Data Title Screen (ALL) or Monthly Data Title

Screen (MONTHLY) is displayed will toggle between the two screens.

• Pressing D while the Cumulative Data Title Screen (ALL) is displayed will switch

to the Monthly Data Title Screen (MONTHLY). To return to the Cumulative Data

Title Screen from the Monthly Data Title Screen, press D.

• Pressing E while the Cumulative Data Title Screen (ALL) or Monthly Data Title

Screen (MONTHLY) is displayed will display the details for the applicable data.

• Pressing D while a Cumulative Data Screen or Monthly Data Screen is displayed

will switch between the distance and energy consumption screen.

• Pressing B while the Cumulate Data Screen or Monthly Data Screen is displayed

will return to the applicable title screen.

��

• Up to 16 months of data can be maintained in watch memory at any time. Storing

more data when there are already 16 months of data will cause the oldest data to

be deleted to make room for the new data.

To swap middle and lower display area contents

Hold down D for about two seconds until the following sequence is complete: Display

contents ﬂash.

Display contents stop ﬂashing.

Watch beeps.

➞

• This will swap the contents of the middle display area with the contents of the lower

��

display area.

��

To select display information

Use D to scroll through available display information.

��

5. Press C four times to return to the Timekeeping Mode.

To delete a workout record

While the workout record you want to delete is displayed, hold down A until a

conﬁrmation screen like the one shown below appears. Keep A depressed for about

another two seconds to delete the record.

• Releasing A while the conﬁrmation screen is displayed will exit the delete operation

without deleting the data.

��

• If you start running for a certain amount of time while an elapsed time measurement

operation is in progress, the watch will detect it and start displaying your number of

steps and average pace.

��

• Changes in pace are not reﬂected immediately. If you suddenly drop your speed

while average pace is displayed, the displayed value will maintain the current (pre-

slowdown) pace for a short while before being adjusted.

To delete cumulative data or monthly data

While the screen for the type of data you want to delete (cumulative or monthly) is

displayed, hold down A until a conﬁrmation screen appears. Keep A depressed for

about another two seconds to delete the record.

• The average pace value will show − − − if your lap time is 20 seconds or less.

• Releasing A while the conﬁrmation screen is displayed will exit the delete operation

Viewing Memory Records

without deleting the data.

You can use the Recall Mode to view records currently stored in watch memory.

• Each record shows data for one workout (stopwatch elapsed time operation).

• The date is the date that the record was stored.

• Monthly data shows cumulative data totals (distance and energy consumption) for

one month.

• When you delete cumulative data, the date in the lower display area will change to

the date of deletion.

• If a stopwatch elapsed time operation is in progress when you perform the above

operation, the in-progress data will not be deleted.

• Cumulative data shows cumulative data totals (distance and energy consumption)

since the last time the data was cleared (reset).

• − − − is shown if there is no data recorded.

• The SENSOR indicator will be on the display in the Recall Mode if a stopwatch

elapsed time operation is currently in progress. The SENSOR indicator will be

ﬂashing if the watch detects you are running.

Download from Www.Somanuals.com. All Manuals Search And Download.

Operation Guide 3166

To stop the alarm beeper

Press any button.

Using the Countdown Timer

You can set the start time of the countdown timer in units of one minute up to 100

hours. The watch beeps for 5 seconds when the end of the countdown is reached.

• To enter the Countdown Timer Mode, press C three times while in the Timekeeping

Mode.

To test the alarm

In the Alarm Mode, hold down B to sound the alarm.

To conﬁgure countdown timer settings

Using World Time

1. While the current starting time is displayed in the

��

Countdown Timer Mode, hold down A for about two

seconds until the hour digits start to ﬂash on the display.

• This is the setting screen.

World time lets you display the current time in any one of 48 cities (31 time zones)

around the world.

• When you enter the World Time Mode, the screen for the city that was displayed

when you last exited the mode appears ﬁrst.

• The World Time seconds count is linked with the Timekeeping Mode seconds count.

• The same 12-hour/24-hour format you select for the Timekeeping Mode time is also

applied in the World Time Mode.

• The watch will exit the countdown timer setting

mode automatically if you do not perform any button

operation for about two or three minutes.

2. Use D (+) and B (–) to change the hour setting.

• Holding down either button scrolls the setting at high

speed.

• To enter the World Time Mode, press C ﬁve times while in the Timekeeping Mode.

3. Press C to move the ﬂashing to the minute digits.

• This causes the minute digits to ﬂash.

Important!

If the current time settings of the World Time Mode cities are incorrect, correct the

setting of the current time in the Timekeeping Mode.

• As with the hours setting, use D (+) and B (–) to

��

change the minutes setting.

4. When all of the settings are the way you want, press A

Using World Time

to exit the setting screen.

In the World Time Mode, use D (eastward) and B (westward) to scroll through the

city codes until the one whose time you want to view is displayed.

• Holding down either button will scroll at high speed.

To use the countdown timer

In the Countdown Timer Mode, use E to start the

countdown.

��

• For details about the sequence of the City Codes, see the “City Code Table”.

•

Press B to stop elapsed timing. Press E again to

restart timing.

��

•

The time counts down in 1-second steps.

Pressing B while the countdown timer is stopped will

reset it to the start time.

��

To stop the time up beeper

Pressing any button while the time up beeper is sounding

will stop it.

��

Using Summer Time

Summer time, or Daylight Saving Time (DST) as it is called in some countries, calls for

setting clocks ahead one hour from standard time during the summer season.

Note that the start and end of summer time, and whether summer time is used at all

depends on each country and geographic area.

Alarms and Hourly Time Signal

Your watch comes with ﬁve alarms and an hourly time signal.

Daily Alarms (AL 1 to AL 5)

The watch beeps for about 10 seconds when an alarm time is reached.

• ON

Turns on summer time and advances standard time by one hour.

• OFF

Hourly Time Signal

Turns off summer time and returns to standard time.

The hourly time signal causes the watch to beep every hour on the hour.

• Alarm and hourly time signal settings are conﬁgured in the Alarm Mode, which you

enter by pressing C four times while in the Timekeeping Mode.

To turn on summer time (DST) for a World Time city

1. In the World Time Mode, use D (eastward) and B

��

(westward) to scroll through the city codes until the one

whose summer time (DST) setting you want to change

is displayed.

To display an alarm screen

In the Alarm Mode, use D to cycle through the alarm

��

screens.

2. Hold down A to toggle the displayed city’s summer

time setting on (DST displayed, time advanced by one

hour) or off (DST not displayed, standard time).

• Holding down D scrolls at high speed.

If the currently selected city is also your Home City, the

summer time (DST) setting you select here also will be

applied in the Timekeeping Mode.

��

•

��

Illumination

This watch has an EL (electro-luminescent) panel that causes the entire display to

glow for easy reading in the dark. In any mode, press to illuminate the display for

To set an alarm time

about one second

1. In the Alarm Mode, display the screen of the alarm

whose setting you want to change.

2. Hold down A for about two seconds until the hour

digits of the current alarm time start to ﬂash. This is the

setting screen.

• Displaying the setting screen also turns on the alarm

automatically and causes the alarm on indicator to

appear on the display.

3. Use D (+) and B (–) to change the hour setting.

• Holding down either button changes the setting at

high speed.

• When setting the hour, make sure you specify AM or

PM (P) correctly when using 12-hour timekeeping, or

that you specify the correct 24-hour time. The same

12-hour/24-hour format you select for the Timekeeping

Mode time is also applied in the Alarm Mode.

��

Illumination Precautions

• The electro-luminescent panel that provides illumination loses power after very long

use.

• Illumination may be hard to see when viewed under direct sunlight.

• The watch may emit an audible sound whenever the display is illuminated. This

is due to vibration of the EL panel used for illumination, and does not indicate

malfunction.

• Illumination turns off automatically whenever an alarm sounds.

• Frequent use of illumination runs down the battery.

��

Troubleshooting

The watch does not count my steps.

4. Press C to move the ﬂashing to the minute digits.

• The watch maintains a step count only while a stopwatch elapsed time operation is

in progress. Steps are not counted while the stopwatch is stopped (display showing

all zeros or a timing paused).

5. Use D (+) and B (–) to change the minute setting within the range of 0 to 59.

• Holding down either button changes the setting at high speed.

6. After all the settings are the way you want, press A to exit the setting screen.

• The watch also will exit the setting screen automatically if you do not perform any

operation for about two or three minutes.

��

To turn an alarm or the hourly time signal on or off

While the screen for an alarm or the hourly time signal is on the display, press B to

toggle it on (on indicator displayed) and off (on indicator not displayed).

• When any alarm or the hourly time signal is turned on, the applicable on indicator is

displayed in all other modes.

��

: A SENSOR indicator appears on the display while the stopwatch is

performing an elapsed time measurement. The indicator ﬂashes while steps

are being counted.

Download from Www.Somanuals.com. All Manuals Search And Download.

Operation Guide 3166

• The watch will detect when you start running while an elapsed time measurement

City Code Table

operation is in progress. At this time it will start displaying the number of steps you

take and other data.

City Code

PPG

HNL

ANC

YVR

LAX

YEA

DEN

MEX

CHI

City

Pago Pago

Honolulu

Anchorage

Vancouver

Los Angeles

Edmonton

Denver

UTC Offset/GMT Differential

–11

–10

–9

• This watch is designed to count your steps only while you are running. It will not

count your steps correctly while you are walking.

–8

–7

Running

Walking

Mexico City

Chicago

New York

Santiago

Halifax

–6

–5

–4

NYC

SCL

YHZ

YYT

RIO

The step count does not change while I am running.

• This watch is designed to count your steps only while you are running. A built-in

sensor detects the movement of your arms to determine whether you are running.

Because of this, looking at the watch while running as shown in the illustration may

make it impossible for the watch to detect that you are running. Let your arm swing

naturally by your side as you run.

St. Johns

Rio De Janeiro

Fernando de Noronha

Praia

–3.5

–3

–2

FEN

RAI

–1

UTC

LIS

Coordinate Universal Time

Lisbon

LON

MAD

PAR

ROM

BER

STO

ATH

CAI

JRS

MOW

JED

THR

DXB

KBL

KHI

London

Madrid

Paris

Rome

Berlin

Stockholm

Athens

The measured distance reading is not correct.

• This watch calculates distance based on the number of steps you take and the stride

length you specify as part of your personal information. Check to make sure that the

stride length setting of your personal information is correct.

• The displayed distance will not be correct if you change your stride length while you

are running.

Cairo

Jerusalem

Moscow

Jeddah

Tehran

Dubai

Kabul

Karachi

Delhi

Kathmandu

Dhaka

+3.5

+4.5

+5.5

+5.75

+6.5

The average pace reading is not correct.

• The average pace is displayed for a lap or split time. A sudden drop in running

speed (such as a shift from very fast running to a pace that is close to walking) will

cause the watch to re-evaluate whether you are still running. In this case, if you

reduce your pace, the same average pace value will remain displayed for a short

while.

DEL

KTM

DAC

RGN

BKK

SIN

Steps are not counted while an alarm is sounding.

• This watch is designed to pause its step count while an alarm is sounding. Such a

short interruption should affect only short distance and short time running.

Yangon

Bangkok

Singapore

Hong Kong

Beijing

Taipei

Seoul

Tokyo

Adelaide

Guam

Sydney

Noumea

Wellington

The number of steps suddenly increases.

HKG

BJS

• When the watch’s sensor does not detect running movement for a certain amount

of time, it judges that you are not running and stops the step count. If the sensor

detects running movement again for a certain amount of time, it starts the count. The

watch keeps track of your steps during the time it is making its judgment, and it will

add those steps to your count if it ultimately decides that you are running.

TPE

SEL

TYO

ADL

GUM

SYD

NOU

WLG

+9.5

+10

Speciﬁcations

+11

+12

Accuracy: Within ±15 seconds average per month

• Based on data as of March 2008.

Timekeeping: Month, day, day of the week, hour, minute, second,

a.m./p.m. (P), 12-hour/24-hour time format,

Standard Time/Daylight Saving Time, Full Auto Calendar (2000 to

2099)

•

The rules governing global times (GMT differential and UTC offset) and summer time are

determined by each individual country.

Stopwatch: Measuring unit: 1/100 second

Measuring Capacity: 99:59'59.99'' (100 hours)

Maximum Number of Lap/Split Times: 999

Cumulative Distance: 999.9 km/621.1 miles

Cumulative Energy Consumption: 23,900.5 kcal/99,999.9 kJ

Cumulative Exercise Time: 9999 hours, 59 minutes

Maximum Average Pace: 220

Cumulative Number of Steps: 999,999

Maximum Number of Laps/Splits: 150

Target Value Input: Target type selection (distance, energy consumption, elapsed

time) and target value

Personal Information Input: Stride length, weight, age, gender, unit switching (for

energy consumption, weight, stride length)

Recall Mode: Workout records, monthly data, cumulative data, best lap

Countdown Timer:

Countdown Unit: 1 second

Setting Unit: 1 minute

Setting Range: 100 hours

Time Up Beeper: 5 seconds

Alarms:

Daily alarms: 5

Settings: Hour, minute

Beeper: 10 seconds

Hourly Time Signal: Beeps twice every hour on the hour

World Time: 48 cities, 31 time zones

Hour, minute, second (second count coordinated with Timekeeping Mode)

Standard Time/Daylight Saving Time

Illumination: EL (electronic-luminescent) backlight

Battery: CR2025

Approximate Battery Life: Approximately 3 years

* 1 hour elapsed time operation, 1.5 seconds light operation, 10 seconds buzzer

operation per day

Download from Www.Somanuals.com. All Manuals Search And Download.

Bialetti Coffeemaker MOKAEXPRESS User Manual
Black Decker Microwave Oven MZ2300P User Manual
Boss Audio Systems Stereo System GT480 User Manual
Bradford White Corp Boiler BJVS User Manual
Braun Electric Toothbrush D17511 User Manual
Briggs Stratton Automobile Parts 127700 User Manual
Brocade Communications Systems Iron 53 1001763 02 User Manual
Brother Fax Machine FAX2580C 2480C User Manual
Cannon Printer Accessories iP 1200 User Manual
Carrier Gas Heater 48GS User Manual