SF-5580
SF-5780
SF-5980
Owner’s Manual
Q
Download from Www.Somanuals.com. All Manuals Search And Download.
Before using the Digital Diary for the first time...
Use the following procedure to load battereis and reset the unit before using it for the
first time.
1. Remove the screw that holds the main battery compartment cover in place and
open the cover.
RESET
2. Load two new batteries into the battery compartment.
• Make sure that the positive (+) and negative (–) ends are facing correctly.
RESET
3. Replace the battery compartment cover and secure it with its screw.
• Take care that you do not overtighten the screw.
4. Pull the insulating tape from the back-up battery by pulling in the direction
indicated by the arrow printed on the tape.
RES
– 1 –
Download from Www.Somanuals.com. All Manuals Search And Download.
– 2 –
5. Press the RESET button on the back of the Digital Diary with a thin, pointed
object.
RESET
RESET
button
6. Press Y.
7. Press OK to reset the Digital Diary or ESC to abort.
• At this time the message “SET TIME!” appears.
• After about two seconds, the Home Time screen appears.
8. Press FUNC, select “Time set”, and then use the procedure on page 18 to set the
Home Time.
• If you turn power off without setting the Home Time, the “SET TIME!” message
appears the next time you turn power on. The Digital Diary will not operate
properly until you set the Home Time.
Important!
• Turn on the unit at least once a month to check the current condition of the
batteries.
Download from Www.Somanuals.com. All Manuals Search And Download.
I Turning Power On and Off
Press ON/OFF to turn power on and off.
Important!
• If nothing appears on the display when you turn on power, it means that the main
batteries are low. Replace the batteries (page 13) and press the RESET button
to resume normal operation.
• Be sure to press the RESET button (page 2) after loading main batteries for the
first time or if the previous set of batteries went dead.
– 3 –
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Before using the Digital Diary for the first time... ............... 1
Turning Power On and Off ...........................................................3
Before using the Digital Diary... ............................................ 8
Introduction ...................................................................................8
Write down important data somewhere! ....................................8
Important Precautions .................................................................8
Getting Started ....................................................................... 9
General Guide ...............................................................................9
Display .........................................................................................10
All-Reset ...................................................................................... 11
Power Supply ..............................................................................12
Turning Power On and Off .........................................................15
Function Menus ..........................................................................16
System Language .......................................................................16
Display Contrast .........................................................................16
Key Input Sound .........................................................................16
Destructive Backspace ..............................................................17
Home Time Mode ................................................................. 18
Using the Daily Alarm.................................................................19
World Time Mode ................................................................. 21
Zone Information Screen ...........................................................22
Data Bank Operations.......................................................... 24
Inputting Text ..............................................................................24
Download from Www.Somanuals.com. All Manuals Search And Download.
Inputting Dates and Times .........................................................25
Display Formats ..........................................................................26
Telephone Directory Mode .................................................. 27
Record Summary ........................................................................28
Memo Mode .......................................................................... 29
Record Summary ........................................................................29
Calendar Mode ..................................................................... 30
Maneuvering Around Calendars ...............................................30
Appointment Markers .................................................................31
Highlighting Calendar Dates .....................................................32
Working Day Count ....................................................................33
Weekly Schedule Screen ...........................................................33
Schedule Keeper .................................................................. 34
Maneuvering Around Schedule Keeper Dates .........................34
Schedule Alarms.........................................................................36
How Schedule Keeper Data is Sorted.......................................36
Schedule Type Labels and Icons ..............................................36
Daily Schedule Screen ...............................................................38
Reminder Mode .................................................................... 39
Reminder Alarms ........................................................................40
To Do Mode........................................................................... 41
Record Summary ........................................................................42
How To Do Data is Sorted ..........................................................43
Priority Icons ...............................................................................43
– 5 –
Download from Www.Somanuals.com. All Manuals Search And Download.
– 6 –
Expense Manager Mode ...................................................... 44
Expense Type Labels and Icons................................................45
Payment Type Labels .................................................................46
Exchange Rate ............................................................................46
Periodic Expense Report ...........................................................47
Record Summary ........................................................................47
Searching for Data ............................................................... 48
Scroll Search ...............................................................................48
Initial Character Search .............................................................48
Wild Card Search ........................................................................49
Date Search .................................................................................49
Editing Data .......................................................................... 50
Deleting Data ........................................................................ 51
Deleting a Single Data Item........................................................51
Deleting All Data Items In a Mode .............................................51
Deleting Marked Data Items Only ..............................................52
Deleting All Data Items In Specific Modes ...............................53
Secret Function .................................................................... 54
Conversion Modes ............................................................... 56
Metric Conversions ....................................................................57
Currency Conversions ...............................................................57
Game Modes......................................................................... 59
Poker Game .................................................................................59
Blackjack Game ..........................................................................61
Calculator Mode ................................................................... 63
Download from Www.Somanuals.com. All Manuals Search And Download.
Data Communications ......................................................... 66
Setting Up for Data Communications .......................................66
Sending Data ...............................................................................68
Sending All Data Items In a Mode .............................................69
Technical Appendix ............................................................. 71
Memory Capacity ........................................................................71
How the Digital Diary sorts data ...............................................72
Error Messages...........................................................................73
Message Table ............................................................................73
Specifications .............................................................................74
– 7 –
Download from Www.Somanuals.com. All Manuals Search And Download.
Before using the Digital Diary...
Introduction
Congratulations on your selection of CASIO’s new SF-5580/SF-5780/SF-5980
(referred to as Digital Diary in this manual). Please keep your manual and all
information handy for future reference.
Write down important data somewhere!
The memory of your Digital Diary holds information only while power is supplied by
the batteries. Always write down important data somewhere.
Important!
• Load batteries (page 1) and perform the all-reset operation described on page
11 before using the Digital Diary for the first time.
Important Precautions
• Never expose the Digital Diary to fire.
• Avoid temperature extremes. Do not locate the Digital Diary in direct sunlight,
near a window, near a heater, etc.
• In very low temperatures display response may slow down or fail entirely. This
conditionistemporaryandoperationshouldresumeundernormaltemperatures.
• Avoid areas subject to excessive moisture, dirt, and dust.
• Avoid dropping the Digital Diary and otherwise subjecting it to strong impact.
• Never bend or twist the Digital Diary.
• Never try to take the Digital Diary apart.
• Do not use a pen, pencil, or other sharp object to press keys.
• To clean the exterior of the Digital Diary, wipe it with a soft cloth dampened in a
weak solution of a mild neutral detergent and water. Be sure to wring out any
excess moisture from the cloth before wiping off the Digital Diary. Never use
benzene, thinner, or any other volatile agent to clean the unit. Doing so can
remove the figures printed on the case or otherwise damage the case finish.
• The contents of this manual are subject to change without notice.
• CASIO COMPUTER CO., LTD. assumes no responsibility for any loss or claims
by third parties that may arise from the use of this product.
• Notethatoncethebacklightislit, itwillstayonaslongas youcontinuetooperate
the calculator.
Leaving the backlight on for long periods greatly reduces battery life!
Press the LIGHT key to manually turn off the backlight.
• Be sure to use alkaline batteries only to power this Digital Diary.
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
Make sure you read this part of the manual.
General Guide
Mode key
Memory keys
Display
10-key pad
Operator keys
Display Change
key
ON/OFF key
Mode keys
Light key
Cursor keys
Scroll/Search
keys
ESC key
Function key
Alpha keyboard
– 9 –
Download from Www.Somanuals.com. All Manuals Search And Download.
– 10 –
I Display
Whenlightingisdim, youcanturnonanEL(electro-luminescent)backlightforeasier
viewing.
To turn on the EL backlight
Pressing the LIGHT key turns on the backlight of the display. If you do not perform
any operation for about 15 seconds, the backlight automatically turns off. However,
note that once the backlight is lit, it will stay on as long as you continue to operate the
Digital Diary.
Leaving the backlight on for long periods greatly reduces battery life!
Press the LIGHT key again to manually turn off the backlight when you are finished
using it.
Display Indicators
K
SHIFT
CAPS
CODE
NEW/EDIT
INDEX
w
DATA
SNOOZE
DAILY
f
KEY
C
L
1
2
3
4
5
6
7
8
9
0
q
1 Telephone Directory Mode
2 Memo Mode
3 To Do Mode
4 Reminder Mode
5 Schedule Keeper Mode
6 Calendar Mode
e SHIFT key operation
r Upper-case input
t CODE key operation
y NEW/EDIT screen
u Index display
i Data display
7 Expense Manager Mode
8 Home Time/World Time Mode
9 Calculator Mode
0 Conversion Modes
q Game Modes
o Snooze feature activated
p Daily alarm on
a Key sound on
s Memory locked
d Low battery warning
f Indicates data below
w Indicates data above
Download from Www.Somanuals.com. All Manuals Search And Download.
I All-Reset
Use the following procedure to reset the unit to its initial settings.
Important!
• Do not use a very sharp pencil or other object to press the RESET button.
• Be sure to reset the unit before using it for the first time.
• Perform the reset operation only after main batteries and back-up battery are
correctly installed.
• Be sure to press the RESET button (page 2) after loading main batteries for the
first time or if the previous set of batteries went dead.
To start the all-reset operation
1. Turn power off.
2. Press the RESET button on the back of the Digital Diary with a thin, pointed
object.
3. Now you should press Y for “yes” or N for “no” in accordance with the conditions
described below.
When to press Y for “yes”
• When this is the first time you are using the unit.
• When you want to reset the unit and clear all data and settings.
• When you are resetting the unit after a data error (page 73).
1. Press Y in response to the message that appears on the display when you start
the all-reset operation.
2. Press OK to reset the Digital Diary or ESC to abort.
• At this time the message “SET TIME!” appears.
• After about two seconds, the Home Time screen appears.
– 11 –
Download from Www.Somanuals.com. All Manuals Search And Download.
– 12 –
3. Press FUNC, select “Time set”, and then use the procedure on page 18 to set the
Home Time.
• If you turn power off without setting the Home Time, the “SET TIME!” message
appears the next time you turn power on. The Digital Diary will not operate
properly until you set the Home Time.
When to press N for “no”
• After replacing the main batteries.
• When you are not resetting the unit to clear all data and settings.
• When you are not resetting the unit after a data error (page 73).
1. Press N in response to the message that appears on the display when you start
the all-reset operation.
• At this time the message “SET TIME!” appears.
• After about two seconds, the Home Time screen appears.
2. Press FUNC, select “Time set”, and then use the procedure on page 18 to set the
Home Time.
• If you turn power off without setting the Home Time, the “SET TIME!” message
appears the next time you turn power on. The Digital Diary will not operate
properly until you set the Home Time.
• Following are the initial settings of the unit after you perform the all-reset
operation.
Home Time:
New York
JAN 1, 1996 (MON)
12:00 AM
12-hour format
London
12:00 AM
Daily alarm — OFF
World Time:
Daily Alarm:
Sound:
Key — ON
English
Messages:
Character input: CAPS — OFF
I Power Supply
Your Digital Diary is powered by two AAA-size batteries, and its memory is protected
by a single CR2032 lithium battery.
Low Battery Warning
Failure of anything to appear on the display after you turn on power or appearance
of the low battery message, “MAIN BATTERIES WEAK! REPLACE THEM! UNIT
WILL NOT TURN ON AGAIN!” (followed by the display turning off in about 10
seconds) normally indicates that main battery power is low.
Download from Www.Somanuals.com. All Manuals Search And Download.
Note, however, that pressing the RESET button on the back of the unit and then
performing steps 1 and 2 of the procedure under “When to press N for “no”” above
can sometimes restore normal operation. When the low battery message appears
on the display even if you perform these steps, it means you should replace the main
batteries as soon as possible.
Note
• Take care that you do not make a mistake and delete memory contents at this
time.
Important!
• ReplacebatteriesonlywhenlowbatterypowerisindicatedbyfailureoftheDigital
Diary to turn on when you press the ON key. Do not replace batteries as long as
the Digital Diary turns on normally when you press the ON key.
• There is not low battery warning for the back-up battery. Be sure to replace the
back-up battery once every 5 years.
• BesureyoukeepaseparatecopyofallimportantdatathatyoustoreintheDigital
Diary.
Battery Precautions
Incorrectly using batteries can cause them to burst or leak, possibly damaging the
interior of the Digital Diary. Note the following precautions.
• Be sure to use alkaline batteries only to power this Digital Diary.
• Besurethatthepositive(+)sideofeachbatteryisfacinginthecorrectdirections.
• Never mix batteries of different types.
• Never mix old batteries and new ones.
• Do not expose batteries to direct heat, let them become shorted, or try to take
them apart.
• Never leave dead batteries in the battery compartment.
• Remove batteries if you do not plan to use the unit for a long time.
• Replacebatteriesatleastonceeveryfiveyears, nomatterhowmuchyouusethe
unit during that period.
• Never try to recharge the batteries that come with the unit.
• Should a battery leak, clean out the battery compartment of the unit immediately,
taking care to avoid letting battery fluid come into direct contact with your skin.
Keep batteries out of the reach of small children. If swallowed, consult with a
physician immediately.
– 13 –
Download from Www.Somanuals.com. All Manuals Search And Download.
– 14 –
To replace the main batteries
Important!
• Do not remove the main batteries from the Digital Diary while the back-up battery
is removed.
• Be sure to replace both batteries with two new ones. Do not mix an old battery
with a new one.
• Be sure to press the RESET button (page 2) after loading main batteries for the
first time or if the previous set of batteries went dead.
• ReplacebatteriesonlywhenlowbatterypowerisindicatedbyfailureoftheDigital
Diary to turn on when you press the ON key. Do not replace batteries as long as
the Digital Diary turns on normally when you press the ON key.
1. Press OFF to turn power off.
2. Remove the screw that holds the battery compartment cover in place and open
the cover.
RESET
3. Remove both old batteries and replace them with new ones.
• Make sure that the positive (+) and negative (–) ends are facing correctly.
4. Replace the battery compartment cover and secure it with its screw.
• Take care that you do not overtighten the screw.
5. Press the RESET button.
• This causes the message “ARE YOU USING A NEW UNIT FOR THE FIRST
TIME(Y/N)?”toappear.BesuretopressNinresponsetothismessage(pressing
Ywilldeletealldatainmemory).Next,continuewiththeproceduresinthesection
title “All Reset” on page 11.
To replace the back-up battery
Important!
• Do not remove the back-up battery from the Digital Diary while the main batteries
are removed.
Download from Www.Somanuals.com. All Manuals Search And Download.
• Be sure to replace the back-up battery at least once every 5 years. Otherwise,
you run the risk of losing data stored in memory.
1. Press OFF to turn power off.
2. Remove the screw that holds the back-up battery compartment cover in place
and open the cover.
RESET
3. Insert a thin, pointed object into (A) and remove the old battery.
(A)
4. Load a new battery into the compartment, making sure that its positive side is
facing up (so you can see it).
5. Replace the battery compartment cover and secure it with its screw.
• Take care that you do not overtighten the screw.
I Turning Power On and Off
Press ON/OFF to turn power on and off.
Important!
• If nothing appears on the display when you turn on power, it means that the main
batteries are low. Replace the batteries (page 13) and press the RESET button
to resume normal operation.
Auto Power Off Function
The unit automatically turns power off if you do not press any key for about three
minutes. Any alarms you set still sound, even if power is turned off.
– 15 –
Download from Www.Somanuals.com. All Manuals Search And Download.
– 16 –
I Function Menus
• Pressing FUNC displays a function menu, whose contents differs depending on
the mode.
• Pressing SHIFT FUNC displays a function menu of general system settings
(system function menu).
• Input the number of the left of the function you want to use to select it.
• To exit from a function menu, press ESC.
I System Language
Your Digital Diary is capable of producing messages in any one of three languages
(English, French, Spanish).
To select the system language
1. Press SHIFT FUNC and then select “Language”.
2. Press the number key that corresponds to the language that you want to use.
• To select “English”, you would press 1.
• The system language automatically changes to English whenever you perform
the RESET operation (page 11).
Note
• In this manual, all display messages are shown in English.
I Display Contrast
Use the following procedure to make the figures on the display darker or lighter.
To adjust display contrast
1. Press SHIFT FUNC and then select “Display contrast”.
2. Use H and J to make display images darker or lighter.
3. Press OK to quit.
I Key Input Sound
When the key input sound is turned on, your Digital Diary emits a beep each time
you press one of its keys.
Download from Www.Somanuals.com. All Manuals Search And Download.
To turn key input sound on and off
1. Press SHIFT FUNC and then select “Key tone”.
Currently selected setting
2. Use H and J to turn the key input sound on and off.
KEY
• The
indicator is on the display while the key input sound is on.
3. Press OK to quit.
I Destructive Backspace
When destructive backspace is turned on, the character at the cursor position is
deleted when you press the BS key.
To turn destructive backspace on and off
1. Press SHIFT FUNC and then select “Backspace”.
2. Use H and J to turn destructive backspace on and off.
3. Press OK to quit.
– 17 –
Download from Www.Somanuals.com. All Manuals Search And Download.
Home Time Mode
The time kept in the Home Time Mode is used for control of various time based
functions.
To enter the Home Time Mode
Press the HOME/WORLD key once.
To set your Home Time zone
1. In the Home Time Mode, press FUNC and then select “Time zone change”.
2. Use K and L to scroll through the city names.
• See page 23 for a complete list of time zones.
3. When the city you want is displayed, press OK.
• You can change your Home Time zone later if you like. When you do, only the
zone changes, without affecting the time or date setting.
To set the time and date
1. In the Home Time Mode, press FUNC and then select “Time set”.
• The hour setting flashes on the display.
• Use H and J to move the flashing selection around the display.
2. Input numbers for the year, month, day, hour, and minutes.
• Input the year as four digits in the range of 1901 through 2099.
• Use 12-hour or 24-hour format depending on the Home Time format (page 19).
•
All illegal input is ignored.
3. With 12-hour time format, press A for AM or P for PM.
4. Press OK to quit.
• Pressing OK resets the seconds count to “00”.
Download from Www.Somanuals.com. All Manuals Search And Download.
To switch between standard time and daylight saving time
In the Home Time Mode, press FUNC and then select “Daylight savings”.
• This toggles to the opposite setting and returns to the Home Time Mode screen.
indicates daylight saving time.
To switch between 12-hour and 24-hour timekeeping
In the Home Time Mode, press FUNC and then select “12/24 hours”.
• This toggles to the opposite setting and returns to the Home Time Mode screen.
The AM/PM indicator indicates 12-hour timekeeping.
• The time format you select is applied for all modes.
To select the date format
1. In the Home Time Mode, press FUNC and then select “Date format”.
2. Select the date format that you want to use.
• The following shows and example of each format
[1] Month/Date/Year: JAN 1, 1996 (MON)
[2] Date/Month/Year: 1 JAN, 1996 (MON)
[3] Year/Month/Date: 1996/1/1 (MON)
• The date format you select is applied in all modes.
I Using the Daily Alarm
The Daily Alarm, it sounds at the same time every day for 20 seconds and the Daily
Alarm screen appears.
To change the Daily Alarm time
1. In the Home Time Mode, press FUNC and then select “Daily alarm set”.
• The hour setting flashes on the display.
• Use H and J to move the flashing.
2. Input numbers for the hour and minutes.
•
All illegal input is ignored.
3. For 12-hour time format, press A for AM or P for PM.
4. Press OK to quit.
• Pressing OK automatically turns on the alarm.
To turn the Daily Alarm on and off
1. In the Home Time Mode, press FUNC and then select “Daily alarm sound”.
2. Use H and Jto turn the Daily Alarm on and off.
3. Press OK.
– 19 –
Download from Www.Somanuals.com. All Manuals Search And Download.
– 20 –
How the Daily Alarm works
The daily alarm sounds at the alarm time you set. A snooze feature sounds the alarm
more than once, helping to make sure you don’t oversleep or miss an appointment.
About the snooze feature
The snooze feature activates (and the SNOOZE indicator appears on the display) if
you do not press any key or if you press the SPACE key after the Daily Alarm starts
to sound.
• If you do not press any key, the alarm stops after 20 seconds, and sounds two
more times every 10 minutes. In this case (you do not press any key), the alarm
sounds a total of three times and then stops.
• Pressing the SPACE key while an alarm is sounding stops the alarm and resets
the snooze feature for three more alarm operations spaced at 10-minute
intervals.
• Pressing any key besides the SPACE key while an alarm is sounding stops the
alarm and cancels the snooze feature, so the alarm does not sound again until
an alarm time is reached.
Note
Note the following important points when you are using the Daily Alarm.
• If the alarm time is reached during data communications, the alarm does not
sound until you complete the communications procedure.
• The alarm may fail to sound if battery power is too low.
Download from Www.Somanuals.com. All Manuals Search And Download.
World Time Mode
With World Time you can view the current time in time zones around the world.
To enter the World Time Mode
Press the HOME/WORLD key twice. From the Home Time Mode, press HOME/
WORLD only once.
Hours different from
Home Time zone
Current World Time
setting
• Every time you press HOME/WORLD, the Digital Diary switches between the
Home Time Mode and World Time Mode.
To scroll through World Time Mode zones
In the World Time Mode, use K and L to scroll from zone-to-zone.
• Hold down either button to scroll at high speed.
To change a World Time zone’s settings
1. In the World Time Mode, display the zone you want.
2. Press FUNC.
3. Switch between 12/24 hour (page 19), switch between standard and daylight
saving time (page 19), and set the date format (page 19).
• TimekeepingformatanddateformatsettingsareappliedtoallWorldTimezones
and to the Home Time Mode.
• Thestandard/daylightsavingtimesettingisappliedtothecurrentlyselectedtime
zone only.
• See page 22 for details on using the Zone Change function menu item.
– 21 –
Download from Www.Somanuals.com. All Manuals Search And Download.
– 22 –
I Zone Information Screen
The zone information screen shows the name of a major city and the time difference
from your Home Time for each World Time zone.
To display the zone information screen
In either the World Time Mode or Home Time Mode, press DISP CHNG to change
to the zone information screen for the displayed zone.
Time difference from your Home Time zone
City in zone
• To exit the zone information screen, press DISP CHNG, ESC, or HOME/
WORLD.
To change zone information screen content
Note
If you change the city name of the zone information screen, the name you input will
also appear on the Home Time and World Time screens.
1. In the World Time Mode, display the zone you want.
2. Press FUNC and select “Zone change”.
3. Change the contents of the screen.
• Use H and J to move the cursor.
• You can input up to 13 characters for the city name.
4. After you make changes, press OK.
• At this time the message “Are you sure (Y/N)?” appears.
5. Press Y to store your changes or N to abort.
Download from Www.Somanuals.com. All Manuals Search And Download.
City List
Time
Differ-
ence
City Name
Midway
Other Cities in Zone
– 06
– 05
– 04
– 03
– 02
– 01
+ 00
+ 01
+ 02
+ 03
+ 04
+ 05
+ 06
+ 07
+ 08
+ 09
+ 10
+ 11
+ 12
+ 13
+ 14
+ 15
+ 16
+ 17
Honolulu
Anchorage
Los Angeles
Denver
San Francisco, Seattle, Las Vegas
El Paso
Dallas, Mexico City, Houston
Washington D.C., Boston, Montreal
Caracas
Chicago
New York
Santiago
R. de Janeiro
F. de Noronha
Azores
London
Rome
Jerusalem
Moscow
Abu Dhabi
Karachi
Sao Paulo, Buenos Aires
Greenwich Mean Time
Paris, Madrid, Amsterdam, Berlin
Cairo, Athens, Helsinki, Beirut
Jeddah, Kuwait, Nairobi
Dubai
Dhaka
Bangkok
Hong Kong
Tokyo
Sydney
Noumea
Auckland
Jakarta, Hanoi
Beijing, Taipei, Singapore, Manila
Seoul, Pyongyang
Guam
Port Vila
Wellington
• The time difference values in the above table are what would appear when
New York is set as the home time.
– 23 –
Download from Www.Somanuals.com. All Manuals Search And Download.
Data Bank Operations
This part of the manual tells you how to input and edit text, and how to protect your
personal data with a password.
I Inputting Text
Input or correction is performed at the current cursor location.
About “data items” and “entries”
Data item
Name entry
Phone 1 entry
Phone 2 entry
Phone 3 entry
Company entry
Address entry
Email entry
Note/Title entry
The above shows a typical Telephone Directory data item, which is made up of a
number of entries. When you are inputting data, prompts appear on the display to tell
you what entry needs text input.
To move the cursor around the screen
Use K, L, H, and J.
Note
• The maximum number of characters you can input for each data item is 255,
including newline symbols and separator marks (page 25).
To input letters and numbers
Press the key that is marked with the letter or number.
To input upper-case letters
Press CAPS to switch between upper-case and lower-case letters. The “CAPS”
indicator shows the keyboard is shift-locked for upper-case letters.
Download from Www.Somanuals.com. All Manuals Search And Download.
To shift the keyboard
PressSHIFTtotemporarilyshiftthekeyboard. Theindicator“S”onthescreenshows
that the keyboard is shifted.
If the keyboard is set for upper-case letters (by the CAPS key), pressing SHIFT
changes to lower-case. As soon as you input one character, the keyboard unshifts.
To input punctuation marks and other symbols
Press CODE and then any key marked with the punctuation or symbol you want to
input. The “CODE” indicator shows that the CODE key was pressed.
To input accented characters
Example: To input é
CODE W e
Newline symbols and separator marks
Each press of B inputs a newline symbol ( ).
Don’t confuse the newline symbol with the separator mark ( ), which is automati-
cally added at the end of data that you are inputting when you press OK to advance
to the next entry.
Separator marks are not shown when you recall data.
To change one character to another
1. Move the cursor to the character you want to change.
2. Input the character you want to change to.
To delete a character
1. Move the cursor to the character you want to delete.
2. Press DEL.
To insert characters
1. Move the cursor to the location of the insertion.
2. Press INS.
• Each press of INS opens up a space at the cursor location.
3. Input the characters you want in the space.
I Inputting Dates and Times
General
• Use the cursor keys to move the cursor.
– 25 –
Download from Www.Somanuals.com. All Manuals Search And Download.
– 26 –
Times
• Use the 12-hour/24-hour format setting of the Home Time.
• With 12-hour format, press A for AM or P for PM.
Dates
• Use the preset date format (page 19).
• The year input range is 1901 through 2099.
• You can enter 20th century years using only two digits (96 = 1996). 21st
century years must be entered in four digits.
I Display Formats
Two display formats (data display format and index display format) are used.
Press DISP CHNG to switch between the index and data display formats.
Data Display Format (Telephone Directory)
• The data display format shows all the entries.
• Use K and L to scroll line-by-line.
Index Display Format (Telephone Directory)
Main entry
Currently
selected item
• The index display format shows a list of one or two entries only.
• The item that is in the top line is the one that is currently selected.
• Use K and L to scroll up and down.
Download from Www.Somanuals.com. All Manuals Search And Download.
Telephone Directory Mode
Telephone Directory data is automatically sorted according to name entries.
To enter the Telephone Directory Mode
1. Press TEL to display the initial Telephone Directory Mode screen.
File title
Number of records
stored in area
Memory usage
Initial prompt
2. Press TEL again to change to another telephone file.
• Each press of TEL changes the file in the following sequence.
TEL-1
TEL-2
TEL-3
To input Telephone Directory data
1. Use TEL to display the initial screen of a Telephone Directory file.
2. Input the name last name first and press OK.
3. Input any telephone numbers, company name, address, e-mail address, and
note or title, pressing OK after each one.
• Prompts appear on the display telling you what to input.
• After the last entry, pressing OK stores the data and returns to the index display
(page 26).
• Data is automatically sorted alphabetically according to the name entry.
Note
• You must input a name. After that, you can skip any entry by pressing OKwithout
inputting anything.
To change a file title
1. Use TEL to display the initial screen of a Telephone Directory file.
2. Press FUNC and then select “File title”.
– 27 –
Download from Www.Somanuals.com. All Manuals Search And Download.
– 28 –
Current file title
Cursor
3. Input up to 13 characters for the title.
• See page 24 for details on how to input characters.
4. Press OK to quit.
To specify Telephone Directory Mode index display contents
1. PressTELtodisplaytheinitialTelephoneDirectoryModescreen,andthenpress
K, L, “, or ‘ to change to the index display.
2. Press FUNC and then select “List type”.
3. Press the number key that corresponds to the entry you want to appear on the
index display.
• The unit changes back to the index display showing the data you specified.
I Record Summary
The record summary provides an overview of each Telephone Directory file.
File title
Number of
records stored
To display the record summary
In the Telephone Directory Mode, press FUNC and then Select “Record summary”.
Press ESC to return to the original Telephone Directory Mode display.
Download from Www.Somanuals.com. All Manuals Search And Download.
Memo Mode
Memo data is stored in the sequence it is input, without sorting.
To enter the Memo Mode
1. Press MEMO to display the initial Memo Mode screen.
File title
Number of records
stored in area
Memory usage
Initial prompt
2. Press MEMO again to change to another Memo Mode file.
• Each press of MEMO changes the file in the following sequence.
MEMO-1
MEMO-2
MEMO-3
To input Memo Mode data
1. Use MEMO to display the initial screen of a Memo Mode file.
2. Input the first line and press B.
• A newline symbol is inserted and the cursor goes down to the next line.
3. Input the rest of your memo.
4. Press OK to quit and return to the index display (page 26).
To change a file title
Use the same procedure as that described for changing a Telephone Directory file
title on page 27.
I Record Summary
The record summary provides an overview of each Memo Mode file.
To display the record summary
In the Memo Mode, press FUNC and then select “Record summary”.
Press ESC to return to your original Memo Mode display.
– 29 –
Download from Www.Somanuals.com. All Manuals Search And Download.
Calendar Mode
The Calendar displays calendars from January 1901 through December 2099.
• Pressing SCHEDULE in the Calendar Mode enters the Schedule Keeper Mode
for the date selected on the Calendar Mode Screen.
• IfthedatecursorislocatedatadatethatincludesReminderModedata, pressing
REMINDER enters the Reminder Mode for that date.
To enter the Calendar Mode
Press CALENDAR.
Current date (flashing)
Highlighted date
Morning
appointment
Afternoon appointment
Week/Day/Remaining days
• The current date (according to the Home Time setting) is selected by the date
cursor.
I Maneuvering Around Calendars
The following describes the basic operations for maneuvering around the calendars.
• Use K, L, H and J to move the date cursor. Holding down any of these keys
moves the date cursor at high speed.
• Press “tomovethedatecursortothefirstofthepreviousmonth, and‘tomove
to the first of the following month.
To jump to a specific date
1. In the Calendar Mode, press FUNC and then select “Date search”.
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Input the month, day and year and then press OK.
To jump a specific number of days
1. In the Calendar Mode, move the date cursor to the start date.
2. Press ! (forward) or @ (backward).
3. Input the number of days you want to jump and then press OK.
• You can input a value in the range of 0 to 999.
4. Press Y to include holidays or N to exclude holidays.
• A holiday is any highlighted date.
About the “active” calendar
Thecalendarontheleftsideofthedisplayisthe“active”calendar. AllCalendarMode
operations are performed on the active calendar.
I Appointment Markers
Appointment markers appear next to each date that contains data in the Schedule
Keeper Mode or Reminder Mode.
Morning Schedule Keeper appointment data
Reminder data
Afternoon Schedule Keeper appointment data
– 31 –
Download from Www.Somanuals.com. All Manuals Search And Download.
– 32 –
I Highlighting Calendar Dates
You can highlight calendar dates to indicate holidays or other special events to
remember.
To highlight and unhighlight individual dates
1. Move the date cursor to the date.
2. Press SPACE to highlight or unhighlight the date.
To highlight days of the week for multiple weeks
Example: To highlight all Sundays from July 1996 to December 1997.
1. In the Calendar Mode, press FUNC and then select “Weekly holiday set”.
Starting month
Ending month
2. Input the start month (7) and year (96), and the end month (12) and year (97).
3. Press OK.
• SUN is flashing because it is selected.
4. Use H and J to move the flashing. Press SPACE to highlight or unhighlight a
day of the week.
• You can specify (highlight) as many days of the weeks as you like.
5. After selecting the days you want, press OK.
• You can unhighlight any date by selecting it with the date cursor and pressing
SPACE.
To clear days of the week for multiple weeks
1. In the Calendar Mode, press FUNC and then Select “Weekly holiday clear”.
2. Input the start month and year, and the end month and year, and then press OK.
• At this time the message “Are you sure (Y/N)?” appears.
3. Press Y to unhighlight, or N to abort.
Download from Www.Somanuals.com. All Manuals Search And Download.
I Working Day Count
Use the following procedures to count the number of working days.
To count working days
1. Move the date cursor to the start day.
2. Press FUNC and then select “Working day count”.
Starting date
Currently
selected date
Count
3. Use the K, L, H and J to move the date cursor.
• The count changes whenever you move the date cursor.
• The date cursor does not stop at highlighted dates, and highlighted dates are
never counted.
• If you move the date cursor to a date before the starting date, the working day
count is negative.
I Weekly Schedule Screen
A weekly schedule screen that lets you see everything for an entire week at a glance.
Selected day (flashing)
Appointment scheduled during this time
Other Schedule
Keeper or
Reminder events
Part of a multiple-day schedule
To display the weekly schedule screen
1. In the Calendar Mode, move the date cursor to the week you want to view.
2. Press DISP CHNG.
• Use K and Lto move the date cursor day-by-day, or “ and ‘ to jump week-
by-week.
3. Press ESC to return to the calendar screen.
– 33 –
Download from Www.Somanuals.com. All Manuals Search And Download.
Schedule Keeper
The Schedule Keeper lets you input the time and a description of your appointment
and set Schedule Alarms.
• Pressing REMINDER in the Schedule Keeper Mode enters the Reminder Mode
for the date that is currently selected in the Schedule Keeper Mode. Pressing
CALENDAR displays the month with the date cursor located at the Schedule
Keeper date.
To enter the Schedule Keeper Mode
Press SCHEDULE to display the initial Schedule Keeper Mode screen.
Mode
Number of records
stored in mode
Memory usage
Initial prompt
• Pressing SCHEDULE in the Calendar Mode displays the Schedule Keeper for
the date where the date cursor is located inside the calendar or weekly schedule
screen.
I Maneuvering Around Schedule Keeper Dates
The following describes the basic operations for selecting a date to input Schedule
Keeper data.
To jump to a specific date
1. In the Schedule Mode, press FUNC and then select “Date search”.
Download from Www.Somanuals.com. All Manuals Search And Download.
• Note that this procedure cannot be started from the daily schedule screen.
2. Input the month, day and year, and then press OK.
To scroll from one date to another
While the Schedule Keeper screen for a date is already displayed, press K or “ to
scroll back to the previous date. Pressing L or ‘ scrolls to the following date.
• If the date that is displayed contains more than one Schedule Keeper data entry,
the above keys scroll through the data one-by-one. The above key operations
change the date only when the first (top) or last (bottom) data item is on the
display.
To input Schedule Keeper data
1. Display the Schedule Keeper screen for the date where you want to input data.
2. Input the description of the appointment.
• Even if there is already schedule data on the display, simply start inputting the
description and the previous data will disappear.
3. Press K and the schedule type specification starts to flash.
• Do not press “ or ‘. Doing so will start a search using the text you input (page
48).
4. Press H or J to display the schedule type selection menu.
• If you do not want to change the default setting of Schedule Type 1, press K
again without pressing H or J.
5. Input a value from 1 to 8 to specify a schedule type and return to the Schedule
Keeper display.
6. Press K and the starting time specification starts to flash.
7. Input the start time and end time of the appointment.
• Use the 12-hour/24-hour format of the Home Time (page 19).
• If you want to input only a start time, don’t input anything for the end time (leave
it the same as the start time).
8. After you finish inputting the start and end time, press J to move to the alarm
time. Use K and L to select the alarm time type and input an alarm time, if
necessary.
– 35 –
Download from Www.Somanuals.com. All Manuals Search And Download.
– 36 –
• While the alarm time is selected, pressing K and L selects one of three alarm
types.
Same-day alarm. This type of alarm is indicated when the first alarm time that
appears is the same as the appointment start time input by you in step 7. This is
the only type of alarm that allows you to set a time.
Previous-day alarm. This type of alarm is indicated when the first alarm time that
appears is “-24:00”. This type of alarm sounds 24 hours before the start time of
the appointment start time input by you in step 7.
No alarm. When there is no time shown for the alarm time, it means that no alarm
is set.
9. After making the alarm time settings you want, press OK to move back to the
schedule type.
10. While the cursor is in the description text, press OK to store all the data.
Note
• You must input a description. After that, you can skip any input by pressing OK
without inputting anything.
I Schedule Alarms
An alarm sounds for 20 seconds and the corresponding Schedule Keeper data
appears on the display. Note the following important points when you are using a
Schedule Alarm.
• The snooze feature is applied to the same-day alarm also just like the Daily
Alarm. See “About the snooze feature” on page 20 for details.
• The alarm indicator and time are automatically cleared after the alarm time is
reached.
• If the alarm time is reached during data communications, the alarm does not
sound until you complete the communications procedure.
• The alarm may fail to sound if battery power is too low.
I How Schedule Keeper Data is Sorted
The following shows how Schedule Keeper data is sorted within each date.
1. By date
2. By time within the same date(data without time comes first)
I Schedule Type Labels and Icons
Schedule Keeper Mode data includes an icon and a schedule type label. Initially,
schedule types are labelled “SCH TYPE 1” through “SCH TYPE 8”, and the initial
default schedule type icon is
.
Download from Www.Somanuals.com. All Manuals Search And Download.
To change schedule type labels and icons
1. Press SCHEDULE to display the initial Schedule Keeper Mode screen.
2. Press FUNC and then select “Define type”.
3. Use K and L to move the pointer to the schedule type you want to change.
4. Input up to 13 characters for the new label you want to use.
• Skip this step if you don’t want to change the label or if you want to wait until after
you change the schedule type icon.
5. Press DISP CHNG to display the menu of schedule type icons.
• If you do not want to change the icon assigned to this schedule type, skip steps
5 through 7.
6. Use K, L, H and J to move the cursor to the icon you want to use. Use “
and ‘ to move between menu screens.
7. When the icon you want is selected, press OK to register it and return to the
schedule type menu.
8. Press OK to store all your changes and return to the initial Schedule Keeper
Mode display.
• You could change the schedule type label before pressing OK in step 8 if you
have not already done so.
To specify Schedule Keeper Mode index display contents
1. Press SCHEDULE to display the initial Schedule Keeper Mode screen, and then
press K, L, “, or ‘ to change to the index display.
2. Press FUNC and then select “List type”.
Pointer (selected type)
Marker
(current setting)
3. Use KandLtomovethepointernexttothescheduletypeyouwanttochange,
and then use H and J to change the setting.
• Schedule types set to “Yes” appear in the index display, while those set to “No”
do not.
4. Press OK to quit and return to the index display.
– 37 –
Download from Www.Somanuals.com. All Manuals Search And Download.
– 38 –
I Daily Schedule Screen
The daily schedule screen provides a quick overview of appointments scheduled for
the day.
Multiple-day appointment
Appointment
without time
Normal appointment
(includes time and
description)
You should use the daily schedule screen to input multiple-day appointments.
To display the daily schedule screen
1. In the Schedule Keeper Mode, display the screen for the date whose schedule
you want to view.
2. Press DISP CHNG to change to the daily schedule screen.
• You can use K, L, “ and ‘ to scroll to another day.
3. Press DISP CHNG to return to the Schedule Keeper data screen.
To input multiple-day schedule data
1. Display the Schedule Mode daily schedule screen.
2. Press FUNC and then select “Set multi day schedule”.
3. Input the starting date and the ending date, and then press OK.
4. Input the description of the appointment (page 35) and specify the schedule type
(page 36).
• Note that you cannot specify start time, end time, or alarm time for multiple-day
schedule data.
Download from Www.Somanuals.com. All Manuals Search And Download.
Reminder Mode
The Reminder Mode helps you keep track of anniversaries, birthdays, and other
important events.
To enter the Reminder Mode
Press REMINDER to display the initial Reminder Mode screen.
Mode
Number of records
stored in mode
Memory usage
Initial prompt
• Pressing REMINDER in the Calendar Mode or Schedule Keeper Mode enters
the Reminder Mode for the date selected in the Calendar Mode or Schedule
Keeper Mode.
To input Reminder data
1. Press REMINDER to display the initial Reminder Mode screen.
2. Press any letter key to change to the data input screen.
3. UseKandLtoselectthealarmtimetypeandinputanalarmtime,ifnecessary.
• ThealarmtypesarethesameasthosefortheScheduleKeeperMode. Seepage
36 for details.
• If you select a previous-day alarm (alarm setting of -24:00), the alarm sounds at
noon the day before date you specified for the Reminder Mode data item.
4. After setting the alarm, press OK to advance to icon input.
• At this time the icon in the upper right of the display starts to flash.
5. Press H or J to display the icon menu.
• If you do not want to change the icon, skip steps 6 and 7.
6. Use K, L, H and J to move the flashing cursor to the icon you want to use.
Use “ and ‘ to move between menu screens.
7. When the icon you want is selected, press OK to register it and return to the
Reminder input screen.
8. Input a description of the Reminder.
9. While the cursor is in the description area, press OK to store all the data.
– 39 –
Download from Www.Somanuals.com. All Manuals Search And Download.
– 40 –
Note
• You must input a description. After that, you can skip any input by pressing OK
without inputting anything.
I Reminder Alarms
When a Reminder Alarm time is reached, an alarm sounds for 20 seconds and the
corresponding Reminder data appears on the display. Press any key to stop the
alarmandreturntothescreenthatwasshownbeforethealarmbegantosound.Note
the following important points when you are using a Reminder Alarm.
• The snooze feature is applied to the same-day alarm also just like the Daily
Alarm. See “About the snooze feature” on page 20 for details.
• If the alarm time is reached during data communications, the alarm does not
sound until you complete the communications procedure.
• The alarm may fail to sound if battery power is too low.
Download from Www.Somanuals.com. All Manuals Search And Download.
To Do Mode
You can classify items according to priority, and even input a To Do message and
icon.
To enter the To Do Mode
1. Press TO DO to display the initial To Do Mode screen.
File title
Number of records
stored in area
Memory usage
Initial prompt
2. Press TO DO again to change to another To Do file.
• Each press of TO DO changes the file in the following sequence.
TO DO-1
TO DO-2
TO DO-3
To input To Do data
1. Use TO DO to display the initial screen of a To Do file.
2. Input the date for the item and then press OK to move to the priority.
3. Press Hor J to display a menu of priority levels.
4. Input a number from 1 to 8 to assign a priority.
5. Press OK to advance to the description and then input text.
6. While the cursor is in the description area, press OK to store all the data.
Note
• You must input a description. You can skip any input by pressing OK without
inputting anything.
To change a file title
1. UseTODOtodisplaytheinitialscreenoftheToDoModefilewhosetitleyouwant
to change.
– 41 –
Download from Www.Somanuals.com. All Manuals Search And Download.
– 42 –
2. Press FUNC and then select “File title”.
Cursor Current file title
3. Input up to 13 characters for the title.
4. After you finish, press OK.
To specify To Do Mode index display contents
1. Press TO DO to display the initial To Do Mode screen, and then press K, L,
“ or ‘ to change to the index display.
2. Press FUNC and then select “List type”.
Pointer (selected type)
Marker (current setting)
3. Use K and L to move the pointer next to the priority you want to change, and
then use H and J to change the setting.
• To Do Mode entries of a priority set to “Yes” appear in the index display, while
those with priorities set to “No” do not.
4. Press OK to quit and return to the index display.
I Record Summary
Therecordsummaryprovidesaquickviewofhowmanydataitemsarestoredineach
To Do Mode file.
To display the record summary
In the To Do Mode, press FUNC and then select “Record summary”.
Press ESC to return to your original To Do Mode display.
Download from Www.Somanuals.com. All Manuals Search And Download.
I How To Do Data is Sorted
To Do data is sorted into chronological order when it is stored in memory.
I Priority Icons
To Do Mode priorities are assigned icons that appear on the screen whenever you
assign a priority.
To priority icons
1. Press TO DO to display the initial To Do Mode screen.
2. Press FUNC and then select “Define type”.
Pointer
3. Use KandL tomovethepointertotheprioritywhoseiconyouwanttochange.
4. Press DISP CHNG to display the menu of priority icons.
5. Use K, L, H and J to move the cursor to the icon you want to use. Use “
and ‘ to move between menu screens.
6. WhentheiconyouwantisselectedpressOKtoregisteritandreturntothepriority
menu.
7. Press OK to return to the initial To Do Mode display.
To check and uncheck a To Do item
1. Display the initial To Do Mode screen and press “ or ‘ to display the index
display.
2. Move the item you want to check or uncheck in the top line of the display.
3. Press OK to check or uncheck the item.
• You can also perform the above operation using the data display. Display the
data display of the item you want to check or uncheck, and then press OK.
• You can delete all checked items by performing the procedure under “To delete
all marked data items” (page 53) while in the To Do Mode.
– 43 –
Download from Www.Somanuals.com. All Manuals Search And Download.
Expense Manager Mode
With the Expense Manager you can store expense data and produce a report that
shows totals for any specific period.
To enter the Expense Manager Mode
1. Press EXPENSE to display the initial Expense Manager Mode screen.
File title
Number of records
stored in area
Memory usage
Initial prompt
2. Press EXPENSE again to change to another Expense Manager file.
• Each press of EXPENSE changes the file in the following sequence.
EXPENSE-1
EXPENSE-2
EXPENSE-3
To input Expense Manager data
1. Use EXPENSE to display the initial screen of an Expense Manager file.
2. Input the date of the expense and press OK to advance to the expense type.
• You can also start data input while the Expense Manager index display or data
display is on the screen by pressing FUNC and then selecting “Daily expense”.
3. Press H or J to display a menu of expense types.
4. Select an expense type and then press OK to advance to the amount.
• The icon assigned to the expense type you select appears on the screen.
5. Input the amount of the expense and press OK to advance to the payment type.
6. Press H or J to display a menu of payment types.
7. Select the payment type and then press OK to advance to the receipt indication.
8. Press H or J to toggle between “Yes” and “No”, and then press OK to advance
to the note area.
9. Input any text you want as a memo.
10. While the cursor is in the note area, press OK to store all of the data.
Download from Www.Somanuals.com. All Manuals Search And Download.
To change a file title
1. Use EXPENSE to display the initial screen of an Expense Manager file.
2. Press FUNC and then select “File title”.
Cursor
Current file title
3. Input up to 13 characters for the title.
4. Press OK to quit.
I Expense Type Labels and Icons
Expense type data includes an icon and a label.
To change expense type labels and icons
1. Press EXPENSE to display the initial Expense Manager Mode screen.
2. Press FUNC and then select “Expense types”.
Pointer
3. Use K and L to move the pointer to the expense type you want.
4. Input up to 13 characters for the label.
• Skip this step if you don’t want to change the expense type label or if you want
to wait until after you change the expense icon.
5. Press DISP CHNG to display the menu of expense icons.
• If you do not want to change the icon assigned to this expense type, skip steps
5 through 7.
6. Use K, L, H and J to move the flashing cursor to the icon you want to use.
Use “ and ‘ to move between menu screens.
7. When the icon you want is selected press OK to register it and return to the
expense type menu.
– 45 –
Download from Www.Somanuals.com. All Manuals Search And Download.
– 46 –
8. Press OK to store all your changes and return to the initial Expense Manager
Mode display.
• YoucouldchangetheexpensetypelabelbeforepressingOKinstep8ifyouhave
not already done so.
To specify Expense Manager Mode index display contents
1. Press EXPENSE to display the initial Expense Manager screen, and then press
K, L, “, or ‘ to change to the index display.
2. Press FUNC and then select “List expense type”.
Pointer (selected type)
Marker (current setting)
3. Use K and L to move the pointer to the expense type you want to change, and
then use H and J to change the setting.
• Expense types set to “Yes” appear in the index display, while those set to “No”
do not.
4. After you are finished, press OK to return to the index display.
I Payment Type Labels
Paymenttypedataincludesalabelthatappearsonthescreenwheneveryoudisplay
the expense data.
To change these labels, use the procedure under “To change expense type labels
and icons” on page 45. The only difference is that you select “Payment types” in step
2, and you skip steps 5 through 7 (because there are not payment type icons).
I Exchange Rate
The expense total in the periodic report is multiplied by the exchange rate value to
produce the “Converted” item amount.
Download from Www.Somanuals.com. All Manuals Search And Download.
To set the exchange rate
1. Press EXPENSE to display the initial Expense Manager Mode screen.
2. Press FUNC and then select “Exchange rate”.
Current setting
3. Input an exchange rate.
• The exchange rate can have an integer part up to 12 digits and a decimal part up
to 12 digits.
4. Press OK to quit.
I Periodic Expense Report
The following procedure produces an on-screen report of all your expenses.
To produce a periodic expense report
1. Press EXPENSE to display the initial Expense Manager screen, and then press
K, L, “, or ‘ to change to the index display.
2. Press FUNC and then select “Report”.
3. Input the starting date and the ending date and then press OK.
• Pressing OK produces an expense report like the one shown below.
4. Use “ and ‘ to change screens to view other.
5. Press ESC to return to the Expense Manager Mode initial display.
I Record Summary
Therecordsummaryprovidesaquickviewofhowmanydataitemsarestoredineach
Expense Manager file.
To display the record summary
In the Expense Manager Mode, press FUNC and then Select “Record summary”.
Press ESC to return to your original Expense Manager Mode display.
– 47 –
Download from Www.Somanuals.com. All Manuals Search And Download.
Searching for Data
This section explains everything you need to know about searching for and recalling
data.
I Scroll Search
Scroll search can be used in the Telephone Directory, Memo, Schedule, Reminder,
To Do, and Expense Manager modes.
To recall data using scroll search
1. Display the initial screen of the mode where you want to search.
2. Press “ or ‘ to change to the index display (page 26).
3. Use K and L to scroll line-by-line. Use “ and ‘ to scroll screen-by-screen.
4. When the item you want is located in the top line of the index display, press DISP
CHNG to change to the data display (page 26).
5. Use K, L, “, and ‘ to scroll through the data on the display.
I Initial Character Search
Initial character search can be used in the Telephone Directory, Memo, Schedule,
Reminder, Expense Manager and To Do modes.
To recall data using initial character search
1. Enter the mode where you want to search for data.
• Initial character search can be started from the initial screen, the index display,
or the data display.
2. Input the first few characters of the text entry you want to find and press “ or ‘.
• When you press “ or ‘, the Digital Diary displays a data display of the first data
iteminwhichtheinitialcharactersofthetextentry(name,description,etc.)match
your input characters. If you input “J” in the Telephone Directory Mode, for
example, you will recall such names as Jones, Jackson, Johnson, etc.
3. Use “ and ‘ toscrollbetweenmatchingdataitemswhenthereismorethanone
match.
Download from Www.Somanuals.com. All Manuals Search And Download.
I Wild Card Search
Wild card search can be used in the Telephone Directory, Memo, Schedule,
Reminder, and To Do modes.
To recall data using wild card search
1. Enter the mode where you want to search for data.
• Wild card search can be started from the initial screen, the index display, or the
data display.
2. Press FUNC and then select “Wild card search”.
3. Input some characters and press OK.
• When you press OK, the Digital Diary displays a data display of the first data item
that has a match of your characters anywhere. If you input “E” in the Telephone
Directory Mode, for example, you would recall such names as Evens, Emily,
Pete, Smythe, etc.
4. Use “ and ‘ toscrollbetweenmatchingdataitemswhenthereismorethanone
match.
I Date Search
Date search can be used in the Schedule Keeper and Reminder modes.
To recall data using date search
1. Enter the mode where you want to search for data.
• Date search can be started from the initial screen, the index display, or the data
display.
2. Press FUNC to display the function menu, and then Select “Date search”.
3. Input the date and press OK.
• When you press OK, the Digital Diary displays the date you specified.
• In the Reminder Mode, the date is displayed only if it contains data. If the date
you specified does not contain any data, the message “NOT FOUND! PRESS
ESC TO QUIT.” appears on the display.
• In the Schedule Keeper Mode, the screen for the date you specify appears,
regardless of whether or not it contains data.
– 49 –
Download from Www.Somanuals.com. All Manuals Search And Download.
Editing Data
The procedures described here can be used in the Telephone Directory, Memo,
Schedule, Reminder, To Do, and Expense Manager modes.
To edit data
1. Enter the mode that contains the data you want to edit, and recall the data (page
48).
2. Change to the data display.
3. Press FUNC and then Select “Edit record”.
4. Make any changes in the data that you want.
5. Press OK to quit.
Notes
• With Schedule Keeper data, you cannot use the above procedure to add start,
end, and alarm times to existing data items. You can, however, change existing
start, end, and alarm times.
• With the Reminder data, you can use the above procedure to add an alarm time.
Download from Www.Somanuals.com. All Manuals Search And Download.
Deleting Data
Use these procedures to delete data.
I Deleting a Single Data Item
This procedure can be used in the Telephone Directory, Memo, Schedule, Re-
minder, To Do, and Expense Manager modes.
To delete a single data item
1. Enter the mode that contains the data you want to delete, and recall the data
(page 48).
• If you are using the index display (page 26), move the data item into the first line
of the index display.
• If you are using the data display (page 26), simply display the item.
2. Press DEL and the message “DELETE RECORD (Y/N)?” appears on the
screen.
• Instead of pressing DEL, you could press FUNC and then input the correct number
of select “Delete record” (“Delete selected record” in the Expense Manager Mode).
3. Press Y to delete, or N to abort.
I Deleting All Data Items In a Mode
The procedure you should use depends on whether the mode whose data items you
are deleting has multiple files (Telephone Directory, Memo, To Do, Expense
Manager) or not (Schedule, Reminder).
To delete all data items from a multiple file mode (Telephone
Directory, Memo, To Do, Expense Manager)
1. Display the initial screen of the mode that contains the data you want to delete.
• You can display the initial screen for any file.
2. Press FUNC and then select “Delete all files”.
Pointer (selected file)
Marker (current setting)
– 51 –
Download from Www.Somanuals.com. All Manuals Search And Download.
– 52 –
3. Use K and L to move the pointer to the file whose setting you want to change,
and then use H and J to change the setting.
• Files set to “Yes” will be deleted, while those set to “No” will not.
4. Press OK.
• At this time the message “Are you sure (Y/N)?” appears.
5. Press Y to delete or N to abort.
To delete all data items from a single file mode (Schedule Keeper,
Reminder)
1. Display the initial screen of the mode that contains the data you want to delete.
2. Press FUNC and then select “Delete all records”.
• At this time the message “ARE YOU SURE (Y/N)?” appears.
3. Press Y to delete or N to abort.
To delete all listed records (Schedule Keeper)
1. Specify the schedule types that you want to appear on the Schedule Mode index
display.
• See “To specify Schedule Keeper Mode index display contents” on page 37.
2. While the Schedule Keeper Mode index display is on the screen, press FUNC
and then select “Delete listed records”.
• At this time the message “DELETE LISTED RECORDS (Y/N)?” appears.
3. Press Y to delete or N to abort.
• Pressing Y deletes only the records whose schedule types you have specified in
step 1 for display in the index display.
Important!
• Be sure to specify the contents of the Schedule Mode index display in step 1 first.
Otherwise, the above operation deletes all Schedule Keeper Mode contents.
I Deleting Marked Data Items Only
The To Do and Expense Manager modes let you mark specific data items for
deletion.
To mark data items for deletion
1. Display the initial To Do or Expense Manager Mode screen and press “ or ‘ to
display the index display.
2. Move the item you want to mark in the top line of the display.
3. Press OK to mark or unmark the item.
• You can also perform the above operation using the data display. Display the
data display of the item you want to mark or unmark, and then press OK.
Download from Www.Somanuals.com. All Manuals Search And Download.
To delete all marked data items
1. While the index display of the To Do or Expense Manager Mode is on the screen,
press FUNC and then select “Delete marked records”.
• At this time the message “DELETE MARKED RECORDS (Y/N)?” appears.
2. Press Y to delete or N to abort.
I Deleting All Data Items In Specific Modes
Use this procedure to delete all data items in selected modes.
To delete all data items in specific modes
1. From any screen, press SHIFT FUNC and then select “Delete all”.
Pointer (selected file)
Marker (current setting)
2. Use K and L to move the pointer next to the mode whose setting you want to
change, and then use H and J to change the setting.
• The files in modes set to “Yes” will be deleted, while those set to “No” will not.
• If all modes are set to “Yes”, this procedure deletes all data in all modes.
3. After you are finished making the settings you want, press OK.
• At this time the message “Are you sure (Y/N)?” appears.
4. Press Y to delete or N to abort.
– 53 –
Download from Www.Somanuals.com. All Manuals Search And Download.
Secret Function
Your Digital Diary lets you protect data you store in the Telephone Directory, Memo,
Schedule, Reminder, To Do, and Expense Manager modes (protected modes) with
a password.
To register a password
1. Press SHIFT FUNC and then select “Password”.
• At this time, “ENTER PASSWORD” appears on the display.
2. Input the password and press OK to register it.
• A password can be up to 6 characters long. You can use any alphabetic
characters or numerals, /, @, or spaces inside a password. You cannot use
characters produced with the CODE key.
• After you register a password, the password input screen clears and you return
to the screen you started from in step 1. The next time you turn the Digital Diary
on and try to enter a protected mode, the password input screen will appear and
you will have to input the registered password before you can access these
modes.
To access protected modes
1. Turn on Digital Diary power.
2. Press the mode key for one of the protected modes.
• “INPUT PASSWORD” appears on the display.
• If you were in a protected mode the last time you turned power off, “INPUT
PASSWORD” appears as soon as you turn on the Digital Diary.
3. Input the correct password and press OK.
• If you input the wrong password, the password input screen remains on the
display.
• Once you input your password, you will not have to input it again, even if you exit
a protected mode and then re-enter it later. Your password input remains valid
until you turn the Digital Diary off or until you manually lock memory (page 55).
To change the password
1. Turn on the Digital Diary.
• “INPUT PASSWORD” appears on the display.
2. Input the correct password and press OK.
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Press SHIFT FUNC and then select “Password”.
4. Select “Modify password”, which causes the currently registered password to
appear.
5. Makeanychangestothepasswordyouwant,andthenpressOKtostorethenew
password.
To delete the password
1. Turn on the Digital Diary.
• “INPUT PASSWORD” appears on the display.
2. Input the correct password and press OK.
3. Press SHIFT FUNC and then select “Password”.
4. Select “Delete password”, which causes a confirmation message to appear
asking if you really want to delete your password.
5. Press Y to delete or N to abort.
• After you delete the password data protected modes can be viewed by anyone.
To lock memory without turning power off
1. While using the Digital Diary after you have input your password, press SHIFT
FUNC and then select “Password”.
2. Press 3 to select “Lock system”.
• Now when you try to enter another protected mode, the password input screen
appears and you will have to input your password again.
– 55 –
Download from Www.Somanuals.com. All Manuals Search And Download.
Conversion Modes
Your Digital Diary actually gives you two conversion modes, one for metric conver-
sion and one for currency conversion.
To enter the Conversion Modes
1. Press CONV to display the initial Unit Conversion Mode screen.
Unit Conversion direction
Equivalent
(1 inch = 2.54cm)
Input/result area
2. Press CONV again to change to the Currency Conversion Mode (page 57) and
display the initial Currency Conversion Mode screen.
Currency Conversion direction
Equivalent
Input/result area
Download from Www.Somanuals.com. All Manuals Search And Download.
I Metric Conversions
All conversion values in this mode are preset and cannot be changed.
inches — centimeters
miles — kilometers
knots — kilometers/h
US tons — kilograms
ounces — grams
yards — meters
feet — yards
UK tons — kilograms
pounds — kilograms
carats — grams
UK gallons — liters
US gallons — liters
calories — joules
horsepower — kilowatts
Fahrenheit — Celsius
To perform a metric conversion
1. Enter the Unit Conversion Mode.
2. Use K and L to find the one you want to use.
3. Use H and J to change the direction of the conversion.
4. Input the value you want to convert from and press OK to display the conversion
result.
5. If you want to view your original input value, press OK again.
I Currency Conversions
Use the Currency Conversion Mode to convert between various currencies. The
following are the default currency names that the unit uses. You can change the
default currency names to other currency names if you want.
USD — U.S. Dollar
GBP — British Pound
FFR — French Franc
DM — Deutsche Mark
ITL — Italian Lira
YEN — Japanese Yen
Important!
• Makesureyouinputtheconversionratesyouwanttousebeforetryingtoperform
a currency conversion. The Digital Diary will not convert from one currency to
another until you do.
To change currency labels and rates
1. Enter the Currency Conversion Mode.
2. Use K and L to find the conversion pair you want to change.
– 57 –
Download from Www.Somanuals.com. All Manuals Search And Download.
– 58 –
3. Press FUNC to change to the editing screen.
4. Input up to five characters for the name of the first currency, and press OK.
5. Input up to five characters for the name of the second currency, and press OK.
6. Input up to 12 digits for the integer and 12 digits for the decimal part for the rate
of the first currency, and press OK.
7. Input up to 12 digits for the integer and 12 digits for the decimal part for the rate
of the second currency, and press OK to complete the procedure.
• Note that one of the currency rates is normally set to 1. To set up a conversion
pair where 1 unit of Currency A equals 100 units of Currency B, you could use
either of the following.
Currency A rate = 1 / Currency B rate = 100
Currency A rate = 0.01 / Currency B rate = 1
• Toleaveeithercurrencynameorrateunchangedintheaboveprocedure, simply
press OK without inputting anything.
To perform a currency conversion
1. Enter the Currency Conversion Mode.
2. Use K and L to find the one you want to use.
3. Use H and J to change the direction of the conversion.
4. Input the value you want to convert from and press OK to display the conversion
result.
5. If you want to view your original input value, press OK again.
Download from Www.Somanuals.com. All Manuals Search And Download.
Game Modes
The Game Modes give you a choice between poker and blackjack.
To enter the Game Modes
1. Press GAME to display the initial Poker Mode screen.
Mode name
Game over indicator
Your points
Bet amount
Bet indicator
You win indicator
Your hand
2. Press M to change to the Blackjack Mode (page 61) and display the initial
Blackjack screen.
Mode name
Game over indicator
Your points
Bet amount
Bet indicator
Your hand
I Poker Game
The following describe rules and procedures for playing the poker game.
Poker Game Rules
• The game is 5-card draw.
• Unlike standard poker, you do not play against other players. Instead, you try to
accumulate points. The following table shows how many point are awarded for
each type of hand.
– 59 –
Download from Www.Somanuals.com. All Manuals Search And Download.
– 60 –
Bet 20
Type of Hand
Royal Flush
Straight Flush
Four of a Kind
Full House
Bet 10
2500
500
250
80
Bet 30
7500
1500
750
240
150
120
90
Bet 40
10000
2000
1000
320
Bet 50
12500
2500
1250
400
5000
1000
500
160
100
80
Flush
50
200
250
Straight
40
160
200
Three of a Kind
Two Pair
30
60
120
150
20
40
60
80
100
One Pair (Jacks or better)
10
20
30
40
50
Note that no points are awarded for anything less than a pair of Jacks.
• The relative value of the cards is meaningless. Two pair always scores the same
number of points, regardless of what cards make up the two pair.
• Before cards are dealt to start each hand, you can change the bet amount to 10,
20, 30, 40, 50. The bet amount cannot be changed once a hand is dealt. The bet
amount is automatically deducted from your point total when each hand is dealt.
• You start with 1,000 points, and the maximum number of points you can
accumulate is 999,999. The game ends when your points reach zero or 999,999.
To play the poker game
1. Enter the Poker Mode.
2. Use B to declare the bet amount if you want.
3. Press H to start the game.
• The first five cards are dealt.
4. Use number keys 1 through 5 to select which cards you want to keep (1 through
5 from left to right).
• Pressing a number key causes the letter “H” (for “Hold”) to appear above the
corresponding card. To deselect a card, press its number button again so the “H”
disappears.
• You can mark anywhere from no cards to all your cards.
5. After you select which cards you want to hold, press H.
• The unmarked cards disappear and are replaced by new cards, and the hand
ends.
Download from Www.Somanuals.com. All Manuals Search And Download.
• If you win, the “Win” indicator appears and the number of points based on your
hand and the amount you bet are added to your point total (see the table).
• If you lose, the “Win” indicator does not appear and your point total remains
unchanged.
6. To play the next hand, continue from step 2, above.
• Repeat the above procedure until you run out of points or until you score 999,999
points.
I Blackjack Game
The following describe rules and procedures for playing the blackjack game.
Blackjack Game Rules
• The game is standard blackjack where you play against the dealer’s cards. The
Digital Diary is always the dealer.
• Before cards are dealt to start each hand, you can change the bet amount to 10,
20, 30, 40, 50. The bet amount cannot be changed once a hand is dealt. The bet
amount is automatically deducted from your point total when each hand is dealt.
• You start with 1,000 points, and the maximum number of points you can
accumulate is 999,999. The game ends when your points reach zero or 999,999.
• You are offered the opportunity to insure (by the message “Insure” appearing on
the display) whenever the dealer’s first card is an ace. Press I to insure when
offered. Insuring costs you one half of your original bet. If the dealer ends up
getting a blackjack, your insurance bet wins and your original bet loses (a push).
If the dealer does not get blackjack, the insurance bet loses and you continue to
play your hand.
• You are offered the opportunity to double down (by the message “Double”
appearing on the display) whenever your first two cards total 10 or 11. Press D
to double down when offered. Doubling down doubles your bet, and causes you
to stand automatically after receiving one more card.
• You can surrender your hand by pressing Q at any time before you receive any
cards after your original two. Surrendering immediately ends the hand and you
forfeit half of the amount you bet.
• You can continue to draw more cards as long as the total of the cards you already
have is less than 21.
• The dealer will always take a card when the dealer’s cards total less than 17,
unless you are already busted (over 21). The dealer always stands when you are
busted.
• At the end of a hand, the player with the higher points without going over 21 wins.
• The following table shows the number of points you can win with each type of
hand.
– 61 –
Download from Www.Somanuals.com. All Manuals Search And Download.
– 62 –
Bet 20
Type of Hand
Double Down
Blackjack
Bet 10
40
Bet 30
120
75
Bet 40
160
100
80
Bet 50
200
125
100
75
80
50
40
30
10
25
Win
20
60
Insurance
15
45
60
Surrender (Fold)
5
15
20
25
To play the blackjack game
1. Enter the Blackjack Mode.
2. Use B to declare the bet amount if you want.
3. Press H to start the game.
• Two cards are dealt to the player and one to the dealer.
• The “Hit”, “Stand”, and “Fold” indicators flash on the display, waiting for the
player’s response. In certain cases, the messages “Insure” or “Double” may also
appear.
4. Press the letter key that corresponds to the operation you want to perform.
• H: hit
S: stand
I : insure
D: double down
Q: fold (surrender)
5. If you draw a card and the total of your cards is still less than 21, repeat step 3.
6. Whenyoudon’twantanymorecards, pressStotellthedealeryouwanttostand.
• At this time the dealer’s hand is completed and the winner is determined.
• If you win, the “Win” indicator appears and the number of points based on your
hand and the amount you bet are added to your point total (see the table).
• If you lose, the “Win” indicator does not appear and your point total remains
unchanged.
7. To play the next hand, continue from step 2, above.
• Repeat the above procedure until you run out of points or until you score 999,999
points.
Download from Www.Somanuals.com. All Manuals Search And Download.
Calculator Mode
The Calculator Mode provides you with all the tools you need to perform a variety of
calculations throughout the day. It also includes a calculation editing feature that lets
you recall the steps of a calculation and make changes.
Calculator Mode key
MRC
M
M
+
C
+
%
AC
Memory keys,
number keys,
operator keys,
etc.
7
4
1
0
8
5
2
9
6
3
+
Cursor keys
•
•
•
C/AC — clears the last value input. Press twice to clear a calculation on the
screen and start a new calculation.
Use the number keys ( 0 through 9 ) to enter values. Press • to input a decimal
point.
Use !, @, # and $ to specify the arithmetic operation that is marked on
each key.
•
•
= — executes a calculation and displays its result.
Use MRC, M , and M+ for calculator memory operations.
@
MRC — recalls the content of the memory, and clears it when pressed twice
successively.
M
@
— subtracts the currently displayed value from the current memory
contents.
M+ — adds the currently displayed value to the current memory contents.
Use % for percentage calculations.
Use ^ for square root calculations.
!/@ — switches the sign of a value between positive and negative.
•
•
•
– 63 –
Download from Www.Somanuals.com. All Manuals Search And Download.
– 64 –
To correct errors in calculations
If you enter a wrong value, press C/AC once and then enter the correct value.
Ifyoupressthewrongarithmeticoperatorkey(!, @,#, $), simplypressthecorrect
key before entering anything else.
About calculation errors...
Whenever an error occurs, the indicator “ERROR” appears on the display.
• When the number of digits in the mantissa of an intermediate or a final result
exceeds 12 digits.
• When the number of digits in the mantissa of a value stored in memory exceeds
12 digits. In this case, the Digital Diary automatically retains the last value stored
that did not exceed 12 digits.
• Division by zero.
To clear errors
Press C/AC once to continue with the same calculation. If you want to clear the
calculation and start again, press C/AC twice.
To enter the Calculation Mode
Press } to display the initial Calculation Mode screen.
Example 1: 21 + 3 = 24
Example 2: 11 + 10% = 12.1
Download from Www.Somanuals.com. All Manuals Search And Download.
To use the calculation edit feature
1. After inputting a calculation, press DISP CHNG to change to the calculation edit
screen.
• You can also display the calculation edit screen by pressing FUNC and then
selecting “Edit calculation”.
2. Use K and L to scroll through the steps of the calculation.
• The Digital Diary stores up to 99 lines of a calculation for editing.
3. When any step you want to edit is on the screen, make the changes you want.
4. After you finish editing the calculation, press = or OK to recalculate.
To clear a calculation
Press DEL twice to clear a calculation. You can also clear a calculation by pressing
FUNC and then selecting “Clear all steps”.
Calculation Examples
0.
53 + 123 − 63 =
963 × (23 − 56) =
(56 × 3 − 89) ÷ 5.2 + 63 =
53q123w63u
23w56e963u
56e3w89r5.2
113.
− 31779.
q63u 78.1923076923
123456e741852u 91586080512.
3ye5u 8.66025403784
123456 × 741852 =
3 × 5 =
12% of 1500
1500e12tu
660r880tu
180.
75.
Percentage of 660
against 880
80 × 9 = 720
−) 50 × 6 = 300
20 × 3 = 60
480
80e9u| – M –
50e6u} – M –
20e3u| – M –
– M –
720.
300.
60.
480.
– 65 –
Download from Www.Somanuals.com. All Manuals Search And Download.
Data Communications
You can transfer data between two CASIO SF-5580, SF-5780, or SF-5980 units,
or between your Digital Diary and a personal computer only. You cannot exchange
data with any other CASIO Digital Diary model. Data communications can be
performed while in the Telephone Directory, Memo, Schedule Keeper, Calendar,
To Do, Reminder, or Expense Manager Mode.
I Setting Up for Data Communications
The following describes what you would do to set up for data communications
between two Digital Diary units or between a Digital Diary unit and a personal
computer.
To connect to another Digital Diary unit
1. Make sure that the power of both units is turned off.
2. Remove the covers from the data communications jacks on the two Digital Diary
units.
3. Connect the two units using the SB-62 cable.
Important!
• Be sure to replace the connector covers on the Digital Diary units when you are
not performing data communications.
Download from Www.Somanuals.com. All Manuals Search And Download.
Performing data communications between a Digital Diary unit and
a personal computer
You must purchase an optional CASIO Data Communication Package in order to
perform data communication between your Digital Diary unit and a personal
computer. Please note that there are a number of different CASIO Data Communi-
cation packages to suit various computers and Digital Diary types. Because of this,
you should note the following important points when purchasing a Data Communi-
cation Package. If you have any question about which package you need, consult
with your dealer.
• Make sure the Data Communication Package is designed for you with your
particular model of personal computer.
• If the proper Data Communication Package is not yet available in your area,
consult with your dealer to find out when it is scheduled to go on sale.
• For information on how to connect the Digital Diary to a personal computer, see
the user’s manual that comes with the Data Communication Package.
To set up the Digital Diary to receive data
1. While any screen is displayed, press FUNC (or SHIFT FUNC) and then select
“Receive data”.
• You can perform the above operation in the Telephone Directory, Memo,
Schedule Keeper, Calendar, To Do, Reminder, or Expense Manager Mode.
2. Press Y.
• This message indicates that the unit is standing by to receive data.
• To abort the receive operation, press ESC.
• This procedure is the same regardless of whether data is being received from
another Digital Diary unit or from a personal computer.
– 67 –
Download from Www.Somanuals.com. All Manuals Search And Download.
– 68 –
I Sending Data
This section tells you how to operate the Digital Diary to send data to another unit or
to a personal computer.
About data transfer types...
There are a number of ways you can transfer data.
All Data Items
With this method, you can send all data items stored in the Telephone Directory,
Memo, Schedule Keeper, Calendar, To Do, Reminder, or Expense Manager Mode.
Mode Data Items
With this method, you can send all data items stored in specific modes (Telephone
Directory, Memo, Schedule Keeper, Calendar, To Do, Reminder, Expense Man-
ager).
In the Schedule Keeper Mode, you can send items that appear on the index display
(which you specified using the function menu’s List type item described on page 37).
One Data Item
With this method, you can send one data item stored in the Telephone Directory,
Memo, Schedule Keeper, To Do, Reminder, or Expense Manager Mode.
Note
• For Calendar Mode data, you can send highlight data.
• If an alarm (Daily Alarm, Schedule Alarm, or Reminder Alarm) is reached while
data is being sent, the alarm does not sound until the data send operation is
complete.
To send one data item
1. Display the data display (page 26) of the item you want to send.
2. Press FUNC and then select “Send record”.
• A message appears asking if you are ready to send.
3. Press Y to start the send operation, or N to abort.
• To interrupt the send operation at any time, press ESC.
• After the send operation is complete, the display returns to the screen that was
on the display before you started the send operation. Then you can repeat the
above procedure to send another item.
Download from Www.Somanuals.com. All Manuals Search And Download.
To send all data items in specific modes
1. Press SHIFT FUNC and then select “Send all”.
Pointer (selected file)
Marker (current setting)
2. Use Kand Lto move the pointer to the mode whose data items you want to
send, and then use Hand Jto change the setting.
• Data in modes set to “Yes” will be sent, while data in modes set to “No” will not.
3. Press OK.
• A message appears asking if you are ready to send.
4. Press Y to start the send operation, or N to abort.
• To interrupt the send operation at any time, press ESC.
• After the send operation is complete, the display returns to the screen that was
on the display before you started the send operation.
To send Calendar data (highlights)
1. In the Calendar Mode, press FUNC and then select “Send (Holidays)”.
• A message appears asking if you are ready to send.
2. Press Y to start the send operation, or N to abort.
• To interrupt the send operation at any time, press ESC.
• After the send operation is complete, the display returns to the screen that was
on the display before you started the send operation. Then you can repeat the
above procedure to send another item.
I Sending All Data Items In a Mode
Theprocedureyoushouldusedependsonwhetherthefilewhosedataitemsyouare
sending has multiple files (Telephone Directory, Memo, To Do, Expense Manager)
or not (Schedule, Reminder).
– 69 –
Download from Www.Somanuals.com. All Manuals Search And Download.
– 70 –
To send all data items from a multiple file mode (Telephone
Directory, Memo, To Do, Expense Manager)
1. Display the initial screen of the mode that contains the data you want to send.
• You can display the initial screen for any file.
2. Press FUNC and then select “Send all files”.
3. Use K and L to move the pointer to the file whose data you want to send, and
then use H and J to change the setting.
• Files set to “Yes” will be sent, while those set to “No” will not.
4. Press OK.
• At this time the message “READY TO SEND (Y/N)?” appears.
5. Press Y to send or N to abort.
• In the Telephone Directory, Memo, and To Do Modes you can also use another
method to send all data items. While the index display or data display is on the
screen, press FUNC and then select “Send all records”. This causes the
message “READY TO SEND (Y/N)?” to appear, so press Y to send or N to abort.
To send all data items from a single file mode (Schedule Keeper,
Reminder)
1. Display the initial screen of the mode that contains the data you want to send.
2. Press FUNC and then select “Send all records”.
• At this time the message “READY TO SEND (Y/N)?” appears.
3. Press Y to send or N to abort.
To send listed records in the Schedule Keeper Mode
1. Enter the Schedule Keeper Mode and specify the items you want to send in the
index display contents.
• See “To specify Schedule Keeper Mode index display contents” on page 37.
2. While the Schedule Keeper Mode index display is on the screen, press FUNC
and then select “Send listed records”.
• At this time the message “READY TO SEND (Y/N)?” appears.
3. Press Y to send or N to abort.
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Appendix
I Memory Capacity
Memory capacity differs according to model.
Model Memory
SF-5580: 128K bytes
SF-5780: 256K bytes
SF-5980: 512K bytes
The following shows the number of items that can be stored in each model.
Telephone Directory
8-character name, 10-character Phone 1 number
SF-5580/SF-5780/SF-5980: 4,000/9,000/19,000
8-character name, 10-character Phone 1 number, 20-character address
SF-5580/SF-5780/SF-5980: 2,000/4,500/9,500
Memo
20-character memo
SF-5580/SF-5780/SF-5980: 3,400/7,700/16,000
To Do
20-character description
SF-5580/SF-5780/SF-5980: 3,200/7,200/15,200
Schedule Keeper
20-character description, alarm time setting
SF-5580/SF-5780/SF-5980: 2,900/6,500/13,500
Reminder
10-character description
SF-5580/SF-5780/SF-5980: 5,000/11,250/23,800
Expense Manager
10-character description
SF-5580/SF-5780/SF-5980: 3,500/7,900/18,600
– 71 –
Download from Www.Somanuals.com. All Manuals Search And Download.
– 72 –
I How the Digital Diary sorts data
Sorting Sequence
The following table shows the sequence used for sorting data in the Telephone
Mode.
1
2
3
4
5
6
7
8
(space) 31
>
?
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
b
c
d
e
f
g
h
i
j
k
l
m
n
o
p
q
r
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
ä
à
å
ç
ê
ë
è
ï
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
#
$
±
`
Á
Í
Ó
Ú
À
È
Ì
Ò
Ù
Ë
Ï
Â
Ê
Î
Ô
Û
Ã
ã
Õ
õ
µ
g
m
q
!
”
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
@
A
B
C
D
E
F
G
H
I
#
$
%
&
’
9
(
)
î
ì
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
Ä
Å
É
æ
Æ
ô
ö
ò
û
ù
Ö
Ü
¢
£
á
í
*
+
,
—
.
J
K
L
/
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
0
1
2
3
4
5
6
7
8
9
:
s
t
u
v
w
x
y
z
~
Ç
ü
é
â
ó
ú
ñ
Ñ
;
<
=
´
z
a
ß
Download from Www.Somanuals.com. All Manuals Search And Download.
I Error Messages
Data Error Message
The data error message appears whenever the Digital Diary’s internal check
discovers a problem with data stored in memory.
Appearance of the data error message indicates that you must perform the all-reset
procedure to correct the problem. Start out with the procedure under “To start the all-
reset operation” on page 11, and continue with the procedure under “When to press
Y for “yes”” on page 11.
Important!
• Even though you are not using the unit for the first time, you must press Y (for
“Yes”) when the unit asks “ARE YOU USING A NEW UNIT FOR THE FIRST
TIME (Y/N)?” in order to reset the unit after a data error occurs.
If you still have trouble after trying the RESET operation, you may have a hardware
problem. If so, consult with your nearest CASIO dealer.
I Message Table
Message
Meaning
Action
NOT FOUND!
PRESS ESC TO QUIT.
Data specified in search
operation does not exist in
memory.
Change specification
or cancel search.
MEMORY FULL,
PRESS ANY KEY.
No more room in memory
for storage of data.
Delete unnecessary
data items from
memory.
ALARM TIME COINCI-
DENT!
Attempt to set an alarm that Set a different alarm
is already used for another
time or change the
existing alarm time.
entry.
– 73 –
Download from Www.Somanuals.com. All Manuals Search And Download.
– 74 –
ALARM TIME ALREADY Attempt to set an alarm for a Set a different alarm
PASSED!
time or date that is already
passed.
time.
DATA COMM. ERROR, Error during data communi- Cancel the operation
PRESS ANY KEY.
cations.
and try again.
ARE YOU USING A
NEW UNIT FOR THE
FIRST TIME (Y/N)?
The reset procedure has
started.
See page 11.
CLEAR MEMORY AND The reset procedure is in
SET UP THE UNIT FOR progress.
OPERATION?
See page 11.
See page 73.
YES (OK)/NO (ESC)
DATA ERROR! CHECK Data corrupted by strong
YOUR OWNER’S
MANUAL FOR
PROCEDURE!
impact, electrostatic charge,
etc..
MAIN BATTERIES
WEAK! REPLACE
THEM! UNIT WILL NOT
TURN ON AGAIN!
The main batteries are
getting weak.
Replace main
batteries immediately
(page 12).
I Specifications
Model: SF-5580/SF-5780/SF-5980
Main Modes:
TelephoneDirectory,Memo,ScheduleKeeper,ToDo,ExpenseManager,Reminder,
Calendar, Home Time, World Time, Calculator, Conversion (metric/currency) and
Game (Poker/Blackjack)
Data storage:
Storage and recall of telephone, memo, schedule, to do, expense, reminder data;
calendar display; editing; memory status display
Download from Www.Somanuals.com. All Manuals Search And Download.
Clock:
World time; reminder alarm; schedule alarm; daily alarm; accuracy under normal
temperatures: 3 seconds average
Calculation:
12-digit arithmetic calculations; independent memory; percentages; square roots;
other mixed calculations
General:
Display element: 26-column × 8-line LCD
Memory capacity: SF-5580: 128KB
SF-5780: 256KB
SF-5980: 512KB
Main component: LSI
Power supply:
Main:
Two AAA-size alkaline batteries (Type: LR03 (AM4))
Back-up: One CR2032 lithium battery
Battery life:
Main:
In Telephone Mode, approximately 100 hours continuous display;
approximately 70 hours with 5 minutes operation and 55 minutes
continuousdisplayperhour;approximately60hourswith5minutes
operation and 52 minutes continuous display, and 3 minutes
backlight operation per hour
Back-up: 5 years if main batteries are replaced as soon as they become
weak. 6 months if dead main batteries are left in the unit.
Power consumption: 0.25W
Auto power off: Approximately 3 minutes after last key operation
Operating temperature: 0°C ~ 40°C (32°F ~ 104°F)
Dimensions:
3
7
5
Unfolded: 8.8H × 163W × 169D mm ( / "H × 6 / "W × 6 / "D)
8
7
16
7
8
5
Folded: 21.5H × 163W × 91.5D mm ( / "H × 6 / "W × 3 / "D)
8
16
8
Weight: 251g (8.9 oz) including batteries
– 75 –
Download from Www.Somanuals.com. All Manuals Search And Download.
CASIO ELECTRONICS CO., LTD.
Unit 6, 1000 North Circular Road
London NW2 7JD, U.K.
Download from Www.Somanuals.com. All Manuals Search And Download.
CASIO COMPUTER CO., LTD.
6-1, Nishi-Shinjuku 2-chome
Shinjuku-ku, Tokyo 163-02, Japan
MO9606-A Printed in China
Download from Www.Somanuals.com. All Manuals Search And Download.
|