E
Digital Camera
EX-Z10
User’s Guide
Thank you for purchasing this CASIO
product.
• Before using it, be sure to read the
precautions contained in this User’s Guide.
• Keep the User’s Guide in a safe place for
future reference.
• For the most up-to-date information about
this product, visit the official EXILIM
Website at http://www.exilim.com/.
K805PCM1DKX
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
26 GETTING READY
Contents
About This Manual ..................................................... 26
General Guide ............................................................ 27
2
INTRODUCTION
Camera
27
Unpacking .................................................................... 2
Features ....................................................................... 9
Precautions ................................................................ 12
Monitor Screen Contents ........................................... 30
REC Modes
30
34
35
PLAY Mode
Changing the Contents of the Monitor Screen
General Precautions
Data Error Precautions
Operating conditions
Condensation
12
19
20
20
21
21
21
21
Attaching the Strap .................................................... 37
Power Requirements .................................................. 37
To load batteries
To replace the batteries
Battery Precautions
Using AC Power
Turning the Camera On and Off
Configuring Power Saving Settings
38
41
41
44
46
48
Power Supply
Lens
Caring for your camera
Other
Using the On-screen Menus ...................................... 49
Configuring Display Language and Clock Settings ... 52
22 QUICK START GUIDE
Load the batteries into the camera ............................ 22
To configure display language and clock settings ..... 23
To record an image .................................................... 24
To view a recorded image .......................................... 25
To delete an image..................................................... 25
To configure display language and clock settings
53
Download from Www.Somanuals.com. All Manuals Search And Download.
3
INTRODUCTION
Exposure Compensation (EV Shift) ........................... 87
Adjusting White Balance ............................................ 89
55 BASIC IMAGE RECORDING
Recording an Image ................................................... 55
Configuring the White Balance Setting Manually
90
Specifying the Recording Mode
Aiming the Camera
Recording an Image (Snapshot Mode)
Using the easy Mode
55
56
57
61
62
Specifying the Exposure Mode .................................. 92
Using Aperture Priority AE
92
94
95
96
Using Shutter Speed Priority AE
Setting Exposure Settings Manually
Exposure Mode Recording Precautions
Recording Precautions
Using the Optical Viewfinder ...................................... 64
Using Zoom ................................................................ 65
Recording Consecutive Images
(Continuous Shutter Mode) ........................................ 97
Optical Zoom
Digital Zoom
65
67
Using the BEST SHOT Mode .................................... 98
Displaying Sample Scenes Individually
Creating Your Own BEST SHOT Setup
To delete a BEST SHOT user setup
100
101
102
Using the Flash .......................................................... 69
Flash Unit Status
Changing the Flash Intensity Setting
Using Flash Assist
71
72
72
Reducing the Effects of Hand or
Subject Movement ................................................... 103
Using the Self-timer ................................................... 74
Specifying Image Size ............................................... 77
Specifying Image Quality ........................................... 78
Shooting with High Sensitivity ................................. 104
Recording Images of Business Cards and
Documents (Business Shot) .................................... 105
To use Business Shot
106
79 OTHER RECORDING FUNCTIONS
Recording a Movie ................................................... 107
Specifying Movie Image Quality
Recording a Movie
108
109
Selecting the Focus Mode ......................................... 79
Using Auto Focus
Using the Macro Mode
Using Pan Focus
Using the Infinity Mode
Using Manual Focus
Using Focus Lock
80
83
84
84
85
86
Recording Audio ....................................................... 111
Adding Audio to a Snapshot
Recording Your Voice
111
113
Using the Histogram................................................. 115
Download from Www.Somanuals.com. All Manuals Search And Download.
4
INTRODUCTION
REC Mode Camera Settings ................................... 118
Displaying the 9-image View .................................... 144
Displaying the Calendar Screen .............................. 145
Playing a Slideshow ................................................. 146
Rotating the Display Image ...................................... 149
Adding Audio to a Snapshot .................................... 150
Assigning Functions to the [̇] and [̈] Keys
Turning the On-screen Grid On and Off
Turning Image Review On and Off
Specifying Power On Default Settings
Specifying ISO Sensitivity
119
120
120
121
123
124
126
126
127
127
128
Selecting the Metering Mode
Using the Filter Function
To re-record audio
151
Specifying Outline Sharpness
Specifying Color Saturation
Playing Back a Voice Recording File ....................... 153
Displaying Camera Images on a TV Screen ........... 154
Specifying Contrast
Selecting the Video Output System
156
Resetting the Camera
157 DELETING FILES
129 PLAYBACK
Deleting a Single File ............................................... 157
Deleting All Files ...................................................... 158
Basic Playback Operation ........................................ 129
Playing an Audio Snapshot
130
Zooming the Display Image ..................................... 131
Resizing an Image ................................................... 132
Cropping an Image................................................... 134
Playing and Editing a Movie..................................... 136
Playing a Movie
Editing a Movie
136
137
Capturing a Still Image from a Movie
(MOTION PRINT)
141
Download from Www.Somanuals.com. All Manuals Search And Download.
5
INTRODUCTION
Using World Time ..................................................... 170
159 FILE MANAGEMENT
To display the World Time screen
To configure World Time settings
170
170
Folders...................................................................... 159
Memory Folders and Files
159
Changing the Display Language.............................. 171
Changing the USB Port Protocol ............................. 172
Protecting Files ........................................................ 160
To protect a single file
To protect all files in memory
160
161
Configuring [
] (REC) and [
] (PLAY)
Power On/Off Functions ........................................... 173
Using the FAVORITE Folder .................................... 161
Formatting Built-in Memory...................................... 174
To copy a file to the FAVORITE folder
To display a file in the FAVORITE folder
To delete a file from the FAVORITE folder
To delete all files from the FAVORITE folder
161
163
164
164
175 USING A MEMORY CARD
Using a Memory Card .............................................. 176
165 OTHER SETTINGS
To insert a memory card into the camera
To replace the memory card
Formatting a Memory Card
176
177
178
Configuring Sound Settings ..................................... 165
To configure sound settings
165
165
Copying Files............................................................ 179
To copy all the files in built-in memory to
To set the confirmation tone volume level
To set the audio volume level for movie and audio
snapshot playback
a memory card
180
166
To copy a specific file from a memory card to
built-in memory
181
Specifying an Image for the Startup Screen ........... 166
Specifying the File Name Serial Number Generation
Method...................................................................... 167
Setting the Clock ...................................................... 168
To select your Home Time zone
To set the current time and date
Changing the Date Format
168
169
169
Download from Www.Somanuals.com. All Manuals Search And Download.
6
C
INTRODUCTION
209 USING THE CAMERA WITH A COMPUTER
182 PRINTING IMAGES
Using the Camera with a Windows Computer ......... 209
DPOF........................................................................ 183
About the bundled CD-ROM
Computer System Requirements
Managing Images on a PC
209
211
212
215
217
218
218
218
To configure print settings for a single image
To configure print settings for all images
184
185
Using PictBridge or USB DIRECT-PRINT ............... 186
Retouching, Reorienting, and Printing a Snapshot
Playing a Movie
Date Printing
190
PRINT Image Matching III ............................................ 191
Viewing User Documentation (PDF Files)
User Registration
Exif Print ................................................................... 192
Exiting the Menu Application
Using the Camera with a Macintosh Computer....... 219
193 VIEWING IMAGES ON A COMPUTER
About the bundled CD-ROM
Computer System Requirements
Managing Images on a Macintosh
Playing a Movie
219
220
221
222
222
223
Using the Camera with a Windows Computer ......... 193
Using the Camera with a Macintosh Computer....... 200
Viewing User Documentation (PDF Files)
To register as a camera user
Using a Memory Card to Transfer Images to a
Computer.................................................................. 204
Memory Data............................................................ 205
224 APPENDIX
DCF Protocol
205
206
207
Memory Folder Structure
Image Files Supported by the Camera
Menu Reference ....................................................... 224
Indicator Lamp Reference........................................ 227
Troubleshooting Guide ............................................. 230
If you have problems installing the USB driver...
Display Messages
235
236
Specifications ........................................................... 238
Download from Www.Somanuals.com. All Manuals Search And Download.
7
INTRODUCTION
IMPORTANT!
• Macintosh and QuickTime are trademarks of Apple
Computer, Inc.
• The contents of this manual are subject to change
without notice.
• CASIO COMPUTER CO., LTD. assumes no
responsibility for any damage or loss resulting from
the use of this manual.
• CASIO COMPUTER CO., LTD. assumes no
responsibility for any loss or claims by third parties
which may arise due to the use or malfunction of the
EX-Z10.
• CASIO COMPUTER CO., LTD. shall not be held
liable for any damages or losses suffered by you or
any third party due to the use of Photo Loader and/or
Photohands.
• CASIO COMPUTER CO., LTD. assumes no
responsibility for any damage or loss caused by
deletion of data as a result of malfunction, repairs, or
battery replacement. Be sure to back up all important
data on other media to protect against its loss.
• Note that the example screens and product
illustrations shown in this User’s Guide may differ
somewhat by the screens and configuration of the
actual camera.
•
MultiMediaCard is a trademark of Infineon
Technologies AG of Germany, and licensed to the
MultiMediaCard Association (MMCA).
• Adobe and Reader are either registered trademarks
or trademarks of Adobe Systems Incorporated in the
United States and/or other countries.
• Other company, product and service names used
herein may also be trademarks or service marks of
others.
• Photo Loader and Photohands are the property of
CASIO COMPUTER CO., LTD. Except as stipulated
above, all copyrights and other related rights to these
applications revert to CASIO COMPUTER CO., LTD.
• The SD logo is a registered trademark.
• Windows, Internet Explorer, Windows Media, and
DirectX are registered trademarks of Microsoft
Corporation.
Download from Www.Somanuals.com. All Manuals Search And Download.
8
INTRODUCTION
I LCD Panel
Features
The LCD panel is a product of the latest LCD
manufacturing technology that provides a pixel yield of
99.99%. This means that less than 0.01% of the total pixels
are defective (they do not turn on or always remain turned
on).
• REC mode or PLAY mode power up (page 46)
Press [
] (REC) or [
] (PLAY) to turn on the camera
and enter the mode you want to use.
• Mode dial (page 55)
A turn of the mode dial selects from among eight different
recording modes.
I Copyright Restrictions
Except for the purposes of your own personal enjoyment,
unauthorized copying of snapshot files, movie files, and
audio files violates copyright laws and international
contracts.
Distribution to third parties of such files over the Internet
without permission of the copyright holder, whether for
profit or for free, violates copyright laws and international
contracts.
• 12X zoom (page 65)
3X optical zoom, 4X digital zoom
• Triple Self-timer (page 74)
The self-timer can be set up to repeat three times,
automatically.
• Quick Shutter (page 81)
When you press the shutter button all the way down
without pausing, the camera immediately records the
image without waiting for Auto Focus to be performed.
This helps to avoid missing a special moment while you
wait for the camera to Auto Focus.
• Auto Focus Area Selection (page 82)
When “
Multi” is selected for the Auto Focus area, the
camera takes simultaneous meter readings at nine
different points and automatically selects the best one.
Download from Www.Somanuals.com. All Manuals Search And Download.
9
INTRODUCTION
• Three exposure modes (pages 92, 94, 95)
• Voice Recording (page 113)
Three exposure modes control aperture and shutter
speed: aperture priority AE (A Mode), shutter speed
priority AE (S Mode), and manual exposure (M Mode).
Quick and easy recording of voice input.
• Calendar screen (page 145)
A simple operation displays a full-month calendar on the
camera’s monitor screen. Each day of the full-month
calendar shows a thumbnail of the first file recorded for
that date, which helps to make searching for a particular
file quicker and easier.
• BEST SHOT (page 98)
Simply select the sample scene that matches the type of
image you are trying to record and the camera performs
troublesome setups automatically for beautiful images
every time.
• Slideshow (page 146)
• Business Shot (page 105)
A slideshow automatically plays back images in sequence
Business Shot automatically corrects rectangular shapes
when recording the image of a business card, document,
whiteboard, or similar subjects from an angle.
at a fixed interval.
• Connect the camera to a TV with the AV cable and
use the TV screen for image recording and viewing
(page 154)
• easy mode (page 61)
This feature eliminates troublesome setups.
• Selectable Sound Settings (page 165)
• Movie recording with audio (page 107)
VGA size, 30 fps, Motion JPEG AVI format
You can configure different sounds to play whenever you
turn on the camera, press the shutter button half-way or
all the way, or perform a key operation.
• MOTION PRINT (page 141)
Capture frames from a movie and create still images that
• World Time (page 170)
are suitable for printing.
A simple operation sets the current time for your current
location. You can select from among 162 cities in 32 time
zones.
• Audio Snapshot mode (page 111)
Use this mode to record snapshots that also include
audio.
• Support for SD memory cards and MMC (MultiMedia
Cards) for memory expansion (page 175)
Download from Www.Somanuals.com. All Manuals Search And Download.
10
INTRODUCTION
• Digital Print Order Format (DPOF) (page 183)
Images can be printed easily in the sequence you want
using a DPOF compatible printer. DPOF can also be used
when specifying images and quantities for printing by
professional print services.
• Bundled with Photo Loader and Photohands
(pages 212, 215, 221)
Your camera comes bundled with Photo Loader, the
popular application that automatically loads images from
your camera to your PC. It also comes with Photohands,
and application that makes image retouching quick and
easy.
• PictBridge and USB DIRECT-PRINT support
(page 186)
Connect directly to a PictBridge or USB DIRECT-PRINT
compatible printer and you can print images without going
through a computer.
• PRINT Image Matching III Compatible (page 191)
III
Images include PRINT Image Matching
setting and other camera setup information). A printer that
III
data (mode
supports PRINT Image Matching
reads this data and
adjusts the printed image accordingly, so your images
come out just the way you intended when you recorded
them.
• Transfer images to a computer simply by connecting
the camera with a USB cable (pages 193, 200)
• DCF Data Storage (page 205)
DCF (Design rule for Camera File system) data storage
protocol provides image compatibility between the digital
camera and printers.
Download from Www.Somanuals.com. All Manuals Search And Download.
11
INTRODUCTION
I Directly Viewing the Sun or Bright Light
Precautions
• Never look at the sun or any other bright light through
the camera’s viewfinder. Doing so can damage your
eyesight.
General Precautions
Be sure to observe the following important precautions
whenever using the EX-Z10. All references in this manual
to “camera” refer to the CASIO EX-Z10 Digital Camera.
I Flash
• Never use the flash unit in areas where flammable or
explosive gas may be present. Such conditions create
the risk of fire and explosion.
• Never fire the flash in the direction of a person
operating a motor vehicle. Doing so can interfere with
the driver’s vision and creates the risk of accident.
• Never fire the flash too close to the eyes of the subject.
Doing so creates the risk of loss of eyesight.
I Test for proper operation before using the
camera!
• Before using the camera to record important images,
make sure you first record a number of test images and
check the results to ensure that the camera is
configured correctly and operating properly (page 57).
I Avoid Use While In Motion
• Never use the camera to record or play back images
while operating an automobile or other vehicle, or while
walking. Looking at the monitor while in motion creates
the risk of serious accident.
Download from Www.Somanuals.com. All Manuals Search And Download.
12
INTRODUCTION
I Display Panel
I Smoke, abnormal odor, overheating, and
other abnormalities
• Do not apply strong pressure to the LCD panel surface
or subject it to strong impact. Doing so can cause the
display panel glass to crack.
• Should the display panel ever become cracked, never
touch any of the liquid inside the panel. Doing so
creates the risk of skin inflammation.
• Should display panel liquid ever get into your mouth,
immediately rinse your mouth out and contact your
physician.
• Should display panel liquid ever get into your eyes or
onto your skin, immediately rinse with clean water for at
least 15 minutes and contact your physician.
• Continued use of the camera while it is emitting smoke
or strange odor, or overheating creates the risk of fire
and electric shock. Immediately perform the following
steps whenever any of the above symptoms are
present.
1. Turn off the camera.
2. If you are using the AC adaptor to power the
camera, unplug it from the wall outlet. If you are
using battery power, remove the batteries from the
camera, taking care to protect yourself against burn
injury.
3. Contact your dealer or nearest CASIO authorized
service center.
I Connections
• Never plug any devices that are not specified for use
with this camera into connectors. Connecting a non-
specified device creates the risk of fire and electric
shock.
I Transport
• Never operate the camera inside of an aircraft or
anywhere else where operation of such devices is
restricted. Improper use creates the risk of serious
accident.
Download from Www.Somanuals.com. All Manuals Search And Download.
13
INTRODUCTION
I Water and Foreign Matter
I Dropping and Rough Treatment
• Water, other liquids, or foreign matter (especially metal)
getting inside the camera creates the risk of fire and
electric shock. Immediately perform the following steps
whenever any of the above symptoms are present.
Particular care is required when using the camera
where it is raining or snowing, near the ocean or other
body of water, or in a bathroom.
• Continued use of the camera after it is damaged by
dropping or other rough treatment creates the risk of
fire and electric shock. Immediately perform the
following steps whenever any of the above symptoms
are present.
1. Turn off the camera.
2. If you are using the AC adaptor to power the
camera, unplug it from the wall outlet. If you are
using battery power, remove the batteries from the
camera.
3. Contact your dealer or nearest CASIO authorized
service center.
1. Turn off the camera.
2. If you are using the AC adaptor to power the
camera, unplug it from the wall outlet. If you are
using battery power, remove the batteries from the
camera.
3. Contact your dealer or nearest CASIO authorized
service center.
I Keep Away From Fire
• Never expose the camera to fire, which can cause it to
explode and creates the risk of fire and electric shock.
Download from Www.Somanuals.com. All Manuals Search And Download.
14
INTRODUCTION
I Disassembly and Modification
I Backing Up Important Data
• Never try to take the camera apart or modify it in any
way. Doing so creates the risk of electric shock, burn
injury, and other personal injury. Be sure to leave all
internal inspection, maintenance, and repair up to your
dealer or nearest CASIO authorized service center.
• Always keep backup copies of important data in
camera memory by transferring it to a computer or
other storage device. Note that data can be deleted in
the case of camera malfunction, repair, etc.
I Memory Protection
I Locations To Be Avoided
• Whenever replacing batteries, be sure to follow the
correct procedure as described in the documentation
that comes with the camera. Incorrectly replacing
batteries can result in corruption or loss of data in
camera memory.
• Never leave the camera in any of the following types of
locations. Doing so creates the risk of fire and electric
shock.
— Areas subject to large amounts of humidity or dust
— Food preparation areas or other locations where oil
smoke is present
— Near heaters, on a heated carpet, in areas exposed
to direct sunlight, in a closed vehicle parked in the
sun, or other areas subject to very high
temperatures
• Never place the camera on an unstable surface, on a
high shelf, etc. Doing so can cause the camera to fall,
creating the risk of personal injury.
Download from Www.Somanuals.com. All Manuals Search And Download.
15
INTRODUCTION
I Batteries
I Alkaline Batteries
• Misuse of batteries can cause them to leak, which
damages and corrodes the area around the batteries
and creates the risk of fire and personal injury. Make
sure you observe the following precautions when using
batteries.
• Should liquid from an alkaline battery ever get into your
eyes, take the following steps.
1. Immediately rinse your eyes with clean water. Do not
rub!
2. See a physician as soon as possible.
— Never try to take batteries apart and never allow
them to become shorted.
Failure to clean alkaline battery fluid from the eyes
creates the risk of loss of sight.
— Do not expose batteries to heat or fire.
— Never mix new batteries with old ones.
— Never mix batteries of different types.
— Do not charge non-rechargeable batteries.
— When loading batteries, make sure their positive (+)
and negative (–) ends are facing correctly.
— When using rechargeable batteries, be sure to read
the Safety Precautions section of the user
documentation that comes with them.
— Use only the batteries that are specified for this
camera.
— If you do not plan to use the camera for a long time,
remove its batteries.
I Rechargeable Batteries
• Should you ever notice any of the following conditions
while using, charging, or storing batteries, immediately
remove them from the camera, and keep them away
from open flame:
— Fluid leaking
— Emission of a strange odor
— Heat emission
— Battery discoloration
— Battery deformation
— Any other battery abnormality
Download from Www.Somanuals.com. All Manuals Search And Download.
16
INTRODUCTION
• Failure to observe any of the following precautions
while using batteries creates the risk of overheating,
fire, and explosion.
— Never use or leave batteries near open flame.
— Never place batteries in a microwave oven, throw
them into fire, or otherwise expose them to intense
heat.
• Battery fluid can damage your eyes. Should battery
fluid get into your eyes accidentally, immediately rinse
them with clean tap water and then consult a physician.
• If batteries are to be used by young children, make
sure that a responsible adult makes them aware of the
precautions and proper handling instructions, and make
sure that they handle batteries correctly.
— Make sure batteries are oriented correctly when you
load them into the camera.
— Never carry or store batteries together with items
that can conduct electricity (necklaces, pencil lead,
etc.).
• Should fluid from batteries accidentally get onto
clothing or your skin, immediately rinse it off with clean
tap water. Prolonged contact with battery fluid can
cause skin irritation.
— Never try to take batteries apart, modify them in any
way, or expose them to strong impact.
— Do not immerse batteries in fresh water or salt
water.
— Do not use or leave batteries under direct sunlight,
in an automobile parked in the sun, or in any other
area subject to high temperatures.
Download from Www.Somanuals.com. All Manuals Search And Download.
17
INTRODUCTION
• Use the AC adaptor where it will not be splashed with
water. Water creates the risk of fire and electric shock.
• Do not place a vase or any other container filled with
liquid on top of the AC adaptor. Water creates the risk
of fire and electric shock.
• Never touch the AC adaptor while your hands are wet.
Doing so creates the risk of electric shock.
• Misuse of the optional AC adaptor creates the risk of
fire and electric shock. Make sure you observe the
following precautions when using the AC adaptor.
— Never locate the power cord near a stove or other
heating device.
— When unplugging from the wall outlet, grasp the
plug on the AC adaptor power cord. Never pull on
the power cord.
— Insert the plug into the wall outlet as far as it will go.
— Unplug the AC adaptor from the wall outlet before
leaving the camera unattended for long periods,
such as when leaving on a trip, etc.
I AC Adaptor (Option)
• Misuse of the optional AC adaptor creates the risk of
fire and electric shock. Make sure you observe the
following precautions when using the AC adaptor.
— Use only the optional AC adaptor specified for this
camera.
— Use a 100 to 240V AC (50/60Hz) wall outlet as a
power source.
— Never plug the power cord into a wall outlet that is
shared by other devices, or into a shared extension
cord.
• Misuse of the AC adaptor can cause it to become
damaged, creating the risk of fire and electric shock.
Make sure you observe the following precautions when
using the AC adaptor.
— Never place heavy objects on the AC adaptor or
subject it to direct heat.
— Never try to modify the AC adaptor or subject it to
bending.
— Do not twist or pull on the power cord.
— Should the power cord or plug ever become
damaged, contact your dealer or nearest CASIO
authorized service center.
— At least once a year, unplug the AC adaptor from
the wall outlet and clean off any dust built up around
the prongs.
Download from Www.Somanuals.com. All Manuals Search And Download.
18
INTRODUCTION
I Battery Life
Data Error Precautions
• The battery lives noted in the User’s Guide are
approximate values until power fails, based on use of
batteries of recommended brands at temperature 23°C
(73°F), and do not guarantee you will be able to
achieve operation for the life noted. Actual battery life is
greatly affected by the battery brand, battery production
date, and ambient temperature.
• Leaving the camera on can run down batteries and
cause the low battery warning to appear. Turn off the
camera whenever you are not using it.
• Sometimes, the camera may shutdown after the low
battery warning appears. If this happens, immediately
replace both of the batteries. Leaving low or dead
batteries in the camera can lead to battery leakage and
data corruption.
• Though you could use alkaline batteries when there are
no other types of batteries available, note that the life of
alkaline batteries will be very short. Use of
• Your digital camera is manufactured using precision
digital components. Any of the following creates the risk
of corruption of data in file memory.
— Removing the batteries or memory card from the
camera, or connecting the USB cable to the camera
while the camera is performing a record or memory
access operation
— Removing the batteries or memory card from the
camera, or connecting the USB cable to the camera
while the operation lamp is still flashing after you turn
off the camera
— Disconnecting the USB cable or disconnecting the AC
adaptor from the camera while a USB data
communication operation is being performed
— Low battery power
* Note that continued use of weak batteries can lead to
malfunction of the camera. Replace the batteries with
new ones as soon as possible after signs of low
power appear.
rechargeable nickel-metal hydride batteries or lithium
batteries is recommended.
— Other abnormal operations
Any of the above conditions can cause an error message to
appear on the monitor screen (page 236). Follow the
instructions provided by the message to eliminate the
cause of the error.
Download from Www.Somanuals.com. All Manuals Search And Download.
19
INTRODUCTION
Operating conditions
Condensation
• This camera is designed for use in temperatures ranging
from 0°C to 40°C (32°F to 104°F). When using the
alkaline batteries that come bundled with the camera,
certain conditions (the amount of time the batteries spent
in storage before being used, operating temperature,
recording conditions) can cause failure of the camera to
operate at temperatures below 5°C (41°F). Because of
this, use of rechargeable nickel metal hydride batteries is
recommended.
• Do not use or keep the camera in the following areas.
— In areas subject to direct sunlight
— In areas subject to high humidity or dust
— Near air conditioners, heaters, or other areas subject
to temperature extremes
• When you bring the camera indoors on a cold day or
otherwise expose it to a sudden change of temperature,
there is the possibility that condensation can form on the
exterior or on interior components. Condensation can
cause malfunction of the camera, so you should avoid
exposing it to conditions that might cause condensation.
• To keep condensation from forming, place the camera
into a plastic bag before moving it into a location that is
much warmer or colder than your current location. Leave
it in the plastic bag until the air inside the bag has a
chance to reach the same temperature as the new
location. If condensation does form, remove the batteries
from the camera and leave the battery cover open for a
few hours.
— Inside of a closed vehicle, especially one parked in the
sun
— In areas subject to strong vibration
Download from Www.Somanuals.com. All Manuals Search And Download.
20
INTRODUCTION
Power Supply
Caring for your camera
• SANYO Electric Co., Ltd. brand type HR-3UA, HR-3UB,or
HR-3UF batteries are recommended when using
rechargeable nickel metal hydride batteries to power this
camera.
• This camera does not have separate batteries for the
clock. The date and time settings of the camera are
cleared whenever power is totally cut off (from both the
batteries and AC adaptor). Be sure to reconfigure these
settings after power is interrupted (page 168).
• Fingerprints, dust, or any other soiling of the lens can
interfere with proper image recording. Never touch the
lens with your fingers. You can remove dust particles
from the lens surface by using a lens blower to blow them
off. Next, wipe the surface of the lens with a soft lens
cloth.
• Fingerprints, dirt, and other foreign matter on the flash
can interfere with proper operation of the camera. Avoid
touching the flash. If the flash becomes dirty, wipe it clean
with a soft, dry cloth.
• If the exterior of the camera needs cleaning, wipe it with a
soft, dry cloth.
Lens
• Never apply too much force when cleaning the surface of
the lens. Doing so can scratch the lens surface and cause
malfunction.
Other
• You may sometimes notice some distortion in certain
types of images, such as a slight bend in lines that should
be straight. This is due to the characteristics of lens, and
does not indicate malfunction of the camera.
• The camera may become slightly warm during use. This
does not indicate malfunction.
Download from Www.Somanuals.com. All Manuals Search And Download.
21
QUICK START GUIDE
Load the batteries into the camera
1. Load the bundled AA-size batteries (LR6) into the camera (page 38).
• You can also use commercially available AA-size rechargeable nickel metal hydride batteries and AA-size lithium
batteries (FR6) to power the camera.
• SANYO Electric Co., Ltd. brand type HR-3UA, HR-3UB,or HR-3UF batteries are recommended when using
rechargeable nickel metal hydride batteries to power this camera.
• Be sure to specify the type of battery you are using to power the camera (page 40).
1
3
Stopper
2
Download from Www.Somanuals.com. All Manuals Search And Download.
22
QUICK START GUIDE
To configure display language and clock settings
• Be sure to configure the following settings
before using the camera to record images.
See page 52 for details.
1. Press the power button to turn on the camera.
2. Use [̆], [̄], [̇], and [̈] to select the language you
1
want.
3. Press [SET] to register the language setting.
4. Use [̆], [̄], [̇], and [̈] to select the geographical area
you want, and then press [SET].
5. Use [̆] and [̄] to select the city you want, and then
press [SET].
2, 3, 4, 5, 6, 7, 8, 9
6. Use [̆] and [̄] to select the summer time (DST) setting
you want, and then press [SET].
[̆]
[̇]
[̄]
7. Use [̆] and [̄] to select the date format setting you
[̈]
want, and then press [SET].
[SET]
8. Set the date and the time.
9. Press [SET] to register the clock settings and exit the
setting screen.
Download from Www.Somanuals.com. All Manuals Search And Download.
23
QUICK START GUIDE
To record an image
See page 55 for details.
Before using a commercially available memory card, be
sure to first format it using the camera’s formatting
procedure. For details about formatting a memory card, see
page 178.
Snapshot mode icon
Green operation lamp
3
1
3
4
1. Press [ ] (REC).
• This enters the REC (recording) mode.
Focus frame
2. Align the mode dial with “ ” (Snapshot mode).
3. Point the camera at the subject, use the monitor
screen or viewfinder to compose the image, and
then press the shutter button half way.
• When the camera finishes its Auto Focus operation, the
focus frame will turn green and the green operation lamp
lights.
4. Holding the camera still, gently press the shutter
button all the way down.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
24
QUICK START GUIDE
To view a recorded image
To delete an image
See page 129 for details.
See page 157 for details.
1
1
2, 3, 4, 5
2
1. Press [ ] (PLAY).
1. Press [ ] (PLAY).
2. Press [̄] ( ).
• This enters the PLAY (playback) mode.
2. Use [̇] and [̈] to scroll through the
3. Use [̇] and [̈] to display the image you want to
images.
delete.
4. Use [̆] and [̄] to select “Delete”.
• To exit the image delete operation without deleting anything,
select “Cancel”.
5. Press [SET] to delete the image.
Download from Www.Somanuals.com. All Manuals Search And Download.
25
GETTING READY
This section contains information about things you need to
know about and do before trying to use the camera.
This term as used in this
manual:
Means this:
“digital noise”
Tiny flecks or “snow” in a
recorded image or on the
monitor screen, which makes
the image look grainy.
About This Manual
This section contains information about the conventions
used in this manual.
I Button Operations
Button operations are indicated by the button name inside
of brackets ([ ]).
I Terminology
The following table defines the terminology used in this
manual.
I On-screen Text
This term as used in this
On-screen text is always enclosed by double quotation
marks (“ ”).
Means this:
manual:
“camera”
The CASIO EX-Z10 Digital
Camera
I Supplementary Information
“file memory”
The location where the
camera is currently storing
images you record (page 57)
•
IMPORTANT!
indicates very important
information you need to know in order to use the camera
correctly.
“batteries”
The AA-size alkaline batteries
•
NOTE
operating the camera.
indicates information that is useful when
“a REC mode”
The currently selected
recording mode (Snapshot,
BEST SHOT, easy, Aperture
Priority AE, Shutter Speed
Priority AE, Manual Exposure,
Voice Recording, movie)
Download from Www.Somanuals.com. All Manuals Search And Download.
26
GETTING READY
I File Memory
General Guide
The term “file memory” in this manual is a general term that
refers to the location where your camera is currently storing
the images you record. File memory can be any one of the
following three locations.
The following illustrations show the names of each
component, button, and switch on the camera.
Camera
• The camera’s built-in memory
• An SD memory card loaded in the camera
• A MultiMediaCard loaded in the camera
I Front
For more information about how the camera stores images,
see page 206.
2
3
4
5
6
1
1 Zoom controller
2 Shutter button
3 Power button
4 Flash
8
7
5 Finder
6 Microphone
7 Lens
8 Self-timer lamp
Download from Www.Somanuals.com. All Manuals Search And Download.
27
GETTING READY
I Back
I Side
J [DC IN 3V]
(AC adaptor
connector)
K [USB/AV]
(USB/AV port)
L Terminal panel cover
9
0
A
B
C
J
K
L
D
E
[̆]
[̇]
[̄]
M Memory card slot
N Memory card cover
[̈]
I
H
G
F
[SET]
Open Terminal Panel Cover/
Memory Card Cover
9 Finder
0 Operation lamp
A [ ] (PLAY mode) button
B [ ] (REC mode) button
C Mode dial
M
N
D Strap ring
E [DISP] button
F [̆][̄][̇][̈]
G [SET] button
H [MENU] button
I Monitor Screen
Download from Www.Somanuals.com. All Manuals Search And Download.
28
GETTING READY
I Bottom
O Battery compartment
P Battery cover
Q Stopper
R Tripod screw hole
* Use this hole when attaching to a tripod.
S Speaker
S
R Q P O
Download from Www.Somanuals.com. All Manuals Search And Download.
29
GETTING READY
Monitor Screen Contents
The monitor screen uses various indicators and icons to keep you informed of the camera’s status.
• Note that the example screens in this chapter are for illustrative purposes only. They do not exactly match the screen
contents actually produced on the camera.
REC Modes
1 Flash mode indicator
(page 69)
5 Self-timer (page 74)
I Screen Indicators
•
appears momentarily
when you select auto focus,
and then disappears.
None 1-Image
1234567 8 9
Auto
Self-timer 10 sec
10s
3 White balance indicator
Flash Off
Self-timer 2 sec
Triple self-timer
2
s
(page 89)
Flash On
0
F
E
x3
Auto
Red-eye reduction
AWB
Daylight
Cloudy
Shade
•
•
appears momentarily
when you select Auto as the
flash mode, and then
6 REC modes (page 55)
D
Snapshot
A
B
disappears.
BEST SHOT
easy
If the camera detects that
flash is required while auto
flash is selected, the flash on
indicator will appear when the
shutter button is pressed half
way.
Day White
Daylight
Aperture Priority AE
C
Shutter Speed Priority
AE
Tungsten
Manual
Manual Exposure
Movie
2 Focus mode indicator
(page 79)
Auto Focus
•
appears momentarily
AWB
when you select auto white
balance, and then
disappears.
Voice Recording
Macro
4 Continuous Shutter
Pan Focus
mode (page 97)
Infinity
None Single shot
Manual Focus
Continuous shutter
Download from Www.Somanuals.com. All Manuals Search And Download.
30
GETTING READY
7 Metering mode indicator A EV value (page 87)
NOTE
(page 124)
• Changing the setting of any one of the following
functions will cause Icon Help text to appear on the
monitor screen.
Flash mode, Focus mode, White balance, Self-timer,
REC modes, EV shift
B Date and time
Multi
(page 168)
Center Weighted
C Battery capacity
Spot
(page 39)
8 • Snapshots: Image size
D Histogram (page 115)
(page 77)
9 • Snapshots: Memory capacity
(pages 59, 238)
E Anti Shake indicator
(page 103)
• Movies: Remaining recording
time (page 109)
F Focus frame
0 • Snapshots: Image quality
(page 78)
(page 58)
•
•
Focusing complete: Green
Focusing failed: Red
F : Fine
N : Normal
E : Economy
• Movies: Image quality
(page 108)
HQ
NORMAL : Normal
LP : Long Play
: High Quality
Download from Www.Somanuals.com. All Manuals Search And Download.
31
GETTING READY
I Exposure Panel
G
The exposure panel is an area in the lower right corner of
the REC modes monitor screen that shows various
adjustable parameters. You can also use the exposure
panel to adjust exposure settings.
H
I
J
Exposure
Panel
K
G Digital zoom indicator (page 67)
H ISO sensitivity (page 123)
• The following explains the items that appear on the
exposure panel. Note that the current REC mode
determines which items appear.
I Aperture value (pages 33, 59, 92, 95)
J Shutter speed value (pages 33, 59, 94, 95)
K Zoom indicator (page 67)
•
•
Left side indicates optical zoom.
Right side indicates digital zoom.
NOTE
• An out of range aperture, shutter speed, or ISO
sensitivity setting causes the corresponding monitor
screen value to turn amber.
Download from Www.Somanuals.com. All Manuals Search And Download.
32
GETTING READY
1 Aperture value (pages 92, 95)
Use this item to adjust the aperture.
• The aperture value is displayed in the
exposure panel when the mode dial is
set to “A” (aperture priority AE) or “M”
(manual exposure).
3 EV shift (exposure compensation value)
(page 87)
Use this item to adjust the exposure
compensation (EV shift) value.
• The EV shift value appears in the
exposure panel when the mode dial is
set to “A” (aperture priority AE) or “S”
(shutter speed priority AE). The EV
shift value also appears when the
mode dial is set to any setting other
than “M” (manual exposure) when “EV
Shift” is assigned as the “L/R Key”
function (page 119).
Aperture value
Shutter speed
EV shift
2 Shutter speed (pages 94, 95)
Use this item to adjust the shutter
speed.
• The shutter speed is displayed in the
exposure panel when the mode dial is
set to “S” (shutter speed priority AE) or
“M” (manual exposure).
4 Manual Focus (MF) setting (page 85)
Use this item for adjust focus
manually.
• The manual focus setting item is
displayed in the exposure panel
when manual focus is selected
MF setting
(indicated by “
screen) using [̆] (
” on the monitor
).
Download from Www.Somanuals.com. All Manuals Search And Download.
33
GETTING READY
5 • Snapshots: Image Size
A White balance indicator
PLAY Mode
(page 77)
(page 89)
12
3
• Movies: Image quality
(page 108)
Auto
AWB
HQ
NORMAL : Normal
LP : Long Play
: High Quality
Daylight
Cloudy
Shade
4
F
E
5
6
7
8
9
6 ISO sensitivity (page 123)
Day White
Daylight
7 Aperture value
(pages 59, 92, 95)
Tungsten
Manual
8 Shutter speed value
(pages 59, 94, 95)
D
C B A 0
B Flash mode indicator
(page 69)
9 Date and time
(page 168)
Flash On
0 Metering mode indicator
1 PLAY mode file type
Snapshot
3 Folder name/File name
Flash Off
(page 124)
(page 159)
Example : When a file named
CIMG0023.JPG is stored in a folder
named 100CASIO
Red-eye reduction
Multi
Movie
Center Weighted
Spot
C REC modes (page 55)
Snapshot ,easy
Audio Snapshot
Voice Recording
100-0023
BEST SHOT
Folder name File name
2 Image protection
Aperture Priority AE
Shutter Speed Priority AE
Manual Exposure
indicator (page 160)
4 • Snapshots: Image quality
(page 78)
F : Fine
N : Normal
E : Economy
• Movies: Recording time (page 109)
D Battery capacity
(page 39)
E Histogram (page 115)
F EV value (page 87)
Download from Www.Somanuals.com. All Manuals Search And Download.
34
GETTING READY
IMPORTANT!
Changing the Contents of the Monitor
Screen
Each press of [DISP] changes the contents of the monitor
screen as shown below.
• Some information may not display properly if you
display an image that was recorded using a different
digital camera model.
I REC Modes
Indicators on
Histogram on
Monitor screen off
Indicators off
Download from Www.Somanuals.com. All Manuals Search And Download.
35
GETTING READY
IMPORTANT!
I PLAY Mode
• Pressing [DISP] will not change monitor screen
contents during standby or recording of an audio
snapshot.
• You can use [DISP] to turn off the monitor screen
only when voice recording in a REC mode. You
cannot turn off the monitor screen for any other
recording function.
• Pressing [DISP] in the Voice Recording REC mode
toggles the monitor screen on (“indicators on”) and
off. While a Voice Recording file is displayed in the
PLAY mode, pressing [DISP] toggles between
“indicators on” and “indicators off”.
Indicators on
Histogram/Details on
• When playing back the content of a Voice Recording
file while “indicators off” is selected (Voice Recording
file icon only on the monitor screen), the monitor
screen will go black about two seconds after you
press [SET] to start playback. The Voice Recording
file icon (indicators off) will reappear after playback is
complete.
Indicators off
Download from Www.Somanuals.com. All Manuals Search And Download.
36
GETTING READY
Attaching the Strap
Power Requirements
Attach the strap to the strap ring as shown in the
illustration.
Your camera features a two-way power supply that lets you
use either AA-size batteries or household AC current. A set
of AA-size alkaline batteries is supplied with the camera.
The other items listed below are available separately.
I Batteries
Strap ring
• Two AA-size alkaline batteries: LR6 (bundled)
• Two AA-size rechargeable nickel-metal hydride batteries
(SANYO Electric Co., Ltd.)
: HR-3UA (Rated Capacitance 2100 mAh)
HR-3UB (Rated Capacitance 2300 mAh)
HR-3UF (Rated Capacitance 2500 mAh)
• Two AA-size lithium batteries: FR6
• Proper operation cannot be guaranteed if you use any
other type of battery other than that noted above.
• When being powered by AA-size alkaline batteries (LR6),
the camera may not operate at all at temperatures of 5°C
(41°F) or lower.
IMPORTANT!
• Be sure to keep the strap around your wrist when
using the camera to protect against accidentally
dropping it.
• The supplied strap is intended for use with this
camera only. Do not use it for any other purpose.
• Never swing the camera around by the strap.
Download from Www.Somanuals.com. All Manuals Search And Download.
37
GETTING READY
To load batteries
SANYO Electric Co., Ltd. brand type HR-3UA, HR-
3UB,or HR-3UF batteries are recommended when using
rechargeable nickel metal hydride batteries to power
this camera. For charging, use only a charger
specifically recommended for HR-3UA , HR-3UB, or HR-
3UF batteries.
1. Turn off the camera.
2. Slide the stopper on the bottom of the camera
in the direction indicated by the arrow, and
then slide the battery cover in the direction
indicated by the arrow.
I Household Current
• AC Adaptor: AD-C30
Stopper
Download from Www.Somanuals.com. All Manuals Search And Download.
38
GETTING READY
3. Load batteries as
shown in the
I Low Battery Indicator
The following shows how the battery capacity indicator on
the monitor screen changes as battery power is used. The
indicator means that remaining battery power is low.
Note that you will not be able to record images while the
illustration.
battery indicator is
. Immediately replace the batteries
whenever either of these indicators appears.
Battery Level
Indicator
High
Low
4. While pressing down
at the point indicated
by the arrow in the
• Note that how the battery level indicator changes from
one level to the next depends on the characteristics of the
particular battery being used.
illustration, slide the
battery cover closed.
IMPORTANT!
IMPORTANT!
• See page 241 for information about battery life.
• Use only AA-size alkaline batteries (LR6), AA-size
lithium batteries (FR6), or AA-size rechargeable
nickel metal hydride batteries to power this camera.
• SANYO Electric Co., Ltd. brand type HR-3UA, HR-
3UB,or HR-3UF batteries are recommended when
using rechargeable nickel metal hydride batteries to
power this camera.
Download from Www.Somanuals.com. All Manuals Search And Download.
39
GETTING READY
ITips to Make the Batteries Last Longer
I Specifying the Battery Type
• If you do not need the flash while recording, select
(flash off) for the flash mode (page 69).
The camera optimizes operation for the type of battery you
are using, which helps to maximize battery life.
• Enable the Auto Power Off and the Sleep features (page
48) to protect against wasting battery power when you
forget to turn off the camera.
• You can also conserve battery power by using [DISP] to
turn off the monitor screen.
1. Turn on the camera.
2. Press [MENU].
• See “Using the On-screen Menus” (page 49) for
information about how to use menus.
3. Use [̇] and [̈] to select the “Set Up” tab.
4. Use [̆] and [̄] to select “Battery Type”, and
then press [̈].
5. Use [̆] and [̄] to select the type of battery
you are using, and then press [SET].
When using this type of battery:
AA-size alkaline (LR6)
Select this setting:
Alkaline
AA-size rechargeable nickel metal
hydride (HR-3UA, HR-3UB, or
HR-3UF SANYO Electric Co., Ltd.)
Nickel Metal
Hydride
AA-size lithium (FR6)
Lithium
Download from Www.Somanuals.com. All Manuals Search And Download.
40
GETTING READY
IMPORTANT!
Battery Precautions
• Proper camera operation is not guaranteed when this
setting does not match the type of battery you are
using to power the camera. Specifying the wrong
type of battery can cause power to suddenly turn off
without retracting the lens, improper display of
remaining battery power, etc.
I Battery Handling Precautions
Misuse of batteries can cause them to leak or explode,
which damages and corrodes the area around the batteries
and creates the risk of fire and personal injury. Make sure
you observe the following precautions when using
batteries.
To replace the batteries
• When loading batteries, make sure their positive (+) and
negative (–) ends are facing correctly.
• Never mix new batteries with old ones.
1. Open the battery cover.
• Never mix batteries of different brands.
2. Carefully tilt the
camera until the
• Use only the batteries that are specified for this camera.
• Never try to take batteries apart and always take care to
avoid conditions where their two ends can become
connected to each other (shorting). Never expose
batteries to heat or throw them into fire.
• Dead batteries are susceptible to leakage, which can
cause serious damage to your camera. Remove batteries
from the camera as soon as you notice they are dead.
• Remove batteries from the camera if you do not plan to
use it for more than two weeks.
batteries slide out.
• Take care to avoid
dropping the
batteries.
3. Load a new set of batteries into the camera
(page 38).
• The batteries that power the camera normally become
warm as you use them.
Download from Www.Somanuals.com. All Manuals Search And Download.
41
GETTING READY
Example2 : Approximately 70 shots when shooting at a
temperature of 0°C (32°F).
ꢀ Alkaline Battery Life
The actual life of alkaline batteries is affected by a variety
of factors, including the battery manufacturer, the amount
of time the batteries spend in storage before you use them,
temperature while you are recording, and photographic
conditions. As a rule, we recommend the use of
MX1500 DURACELL ULTRA alkaline
batteries, monitor on, zoom operation
between full wide and full telephoto every 30
seconds, during which two images are
recorded with flash; power turned off and
rechargeable nickel-metal hydride batteries, which have
longer lives than alkaline batteries.
back on every time 10 images are recorded.
• Note that the above number of shots is approximate and
is provided for reference only. They in no way guarantee
that you will be able to achieve a certain level of
performance under the conditions described above. The
characteristics of the alkaline batteries being used and
certain recording conditions may cause the camera to fail
to operate at temperatures of 5°C (41°F) and lower.
• The PLAY mode requires less power than the REC mode.
If you experience a problem turning on the camera in a
REC mode, try switching to the PLAY mode.
• When using alkaline batteries, intermittent use of the
camera can shorten the life of the batteries.
• When using alkaline batteries, use of the camera in cold
temperatures as described below can shorten the life of
the batteries.
Example1 : Approximately 70 shots when shooting at a
temperature of 0°C (32°F).
Matsushita Battery Industrial Co., Ltd. alkaline
batteries, monitor on, zoom operation
between full wide and full telephoto every 30
seconds, during which two images are
recorded with flash; power turned off and
back on every time 10 images are recorded.
Download from Www.Somanuals.com. All Manuals Search And Download.
42
GETTING READY
I Using Rechargeable Batteries
I Refreshing Rechargeable Batteries
SANYO Electric Co., Ltd. brand type HR-3UA, HR-3UB, or
HR-3UF batteries are recommended when using
rechargeable nickel metal hydride batteries to power this
camera.
Batteries can start to lose their ability to retain a charge if
you do not use them for a long time or when you charge
them repeatedly without allowing their current charge to be
used up completely. If this happens, you may be able to
restore battery capacity by performing the following “battery
refresh” operation to fully discharge the batteries.
IMPORTANT!
• Never mix two batteries of different brands, ages, or
charge levels. Doing so creates the risk of shortened
battery life and can even damage the camera.
• Batteries cannot be recharged while they are loaded
in the camera.
1. Load the chargeable batteries into the camera.
2. While holding down [MENU], press the power button.
This should cause the firmware version screen to flash
on the monitor screen.
3. Leave the camera on until the batteries run out of power
and the camera turns off.
• The battery refresh operation can take as long as 10
hours. The actual amount of time required depends on
battery conditions.
4. After the camera turns off, remove the batteries and
charge them.
Download from Www.Somanuals.com. All Manuals Search And Download.
43
GETTING READY
IMPORTANT!
Using AC Power
• Performing the battery refresh operation reduces the
battery charge level to almost zero. Never load
refreshed batteries into the camera without charging
them first. Though you may be able to momentarily
turn on the camera while refreshed uncharged
batteries are loaded, power may suddenly fail,
leaving the lens extended, or some other mis-
operation may occur.
You need to purchase the optionally available AC adaptor
(AD-C30) in order to be able to power the camera using AC
power.
1. Connect the AC power cord to the AC
adaptor.
• You do not need to perform the above operation
each time you charge the batteries. Only use it if you
notice that you are getting less operation between
charges. Note that you may eventually reach the
point when even the above operation will not refresh
batteries. If this happens, it means that the
rechargeable batteries have reached the end of their
service life and that you will need to purchase new
rechargeable batteries.
2. Open the camera’s terminal panel cover and
connect the AC adaptor to the port marked
[DC IN 3V].
• The above procedure and notes are all based upon
use of SANYO Electric Co., Ltd, type HR-3UA, HR-
3UB, or HR-3UF rechargeable nickel metal hydride
batteries.
Download from Www.Somanuals.com. All Manuals Search And Download.
44
GETTING READY
3. Plug the AC power cord into an electrical
outlet.
I Using AC Adaptor In Another Geographic
Area
• The AC adaptor can be used with any power source rated
from 100V to 240V AC. If you plan to use the AC adaptor
in another country, it is up to you to purchase the
applicable AC power cord that matches the configuration
of power receptacles in that country.
[DC IN 3V]
• Never use the AC adaptor with a voltage converter.
AC adaptor
Terminal panel cover
AC power cord
Plug
Download from Www.Somanuals.com. All Manuals Search And Download.
45
GETTING READY
I AC Adaptor Precautions
• Be sure to turn off power before connecting or
disconnecting the AC adaptor.
Turning the Camera On and Off
I To turn on the camera
• Always turn camera power off before disconnecting the
AC adaptor, even if the camera has batteries installed. If
you don’t, the camera will turn off automatically when you
disconnect the AC adaptor. You also run the risk of
damaging the camera whenever you disconnect the AC
adaptor without first turning power off.
• The AC adaptor may become warm to touch after
extended periods of use. This is normal and is not cause
for alarm.
Press the power button, [
] (REC) or [
] (PLAY). The
green operation lamp will light momentarily, and then
power will turn on. The mode the camera enters depends
on which button you pressed to turn it on.
To enter this mode at
Press this button to turn on the camera:
startup:
REC
Power button or [
[ ] (PLAY)
] (REC)
PLAY
• After using the camera, turn it off and unplug the AC
adaptor from the AC outlet.
• The camera automatically switches over to AC adaptor
powered operation whenever the AC adaptor is plugged
into the camera.
Power button
Green operation lamp
• Always use the AC adaptor to power the camera
whenever it is connected to a computer.
• Never place a blanket or any other cover on the AC
adaptor. Doing so creates the risk of fire.
[
] (PLAY)
[
] (REC)
Download from Www.Somanuals.com. All Manuals Search And Download.
46
GETTING READY
NOTE
I To turn off the camera
• Pressing [
the REC mode, while pressing [
] (REC) to turn on the camera enters
] (PLAY) enters
Press the power button to turn off the camera.
the PLAY mode.
NOTE
• Pressing [
] (PLAY) while in a REC mode switches
• You can setup the camera so it does not turn on
to the PLAY mode. The lens retracts about 10
seconds after switching modes.
when you press [
turn off when you press [
For details, see “Configuring [
] (REC) or [
] (PLAY), or to
] (REC) or [ ] (PLAY).
] (REC) and [
]
IMPORTANT!
(PLAY) Power On/Off Functions” on page 173.
• If camera power is turned off by the Auto Power Off
feature, press the power button, [
(PLAY) to turn it back on again.
• Pressing the power button or [
] (REC) or [
]
] (REC) to turn on
the camera also causes the lens to extend. Take
care to avoid any interference with the lens operation
or allowing anything to strike the lens when it is
extended.
Download from Www.Somanuals.com. All Manuals Search And Download.
47
GETTING READY
G See “Using the On-screen Menus” (page 49) for
information about how to use menus.
Configuring Power Saving Settings
You can configure the settings described below to
conserve battery power.
To configure this feature:
Sleep
Select this setting:
Sleep
Sleep
: Automatically turns off the monitor
screen if no operation is performed for a
specified amount of time in a REC
mode. Performing any button operation
causes the monitor screen to turn back
on.
Auto Power Off
Auto Power Off
5. Use [̆] and [̄] to change the currently
selected setting, and then press [SET].
• Available Sleep settings are: “30 sec”, “1 min”, “2 min”,
and “Off”.
Auto Power Off : Turns off power if you do not perform
any operation for a specified amount of
time.
• Available Auto Power Off settings are: “2 min” and
“5 min”.
• Note that the Sleep feature does not operate in the
PLAY mode.
1. Turn on the camera.
2. Press [MENU].
• Pressing any button while the camera is in the Sleep
state immediately turns the monitor screen back on.
3. Use [̇] and [̈] to select the “Set Up” tab.
4. Use [̆] and [̄] to select the feature whose
setting you want to configure, and then press
[̈].
Download from Www.Somanuals.com. All Manuals Search And Download.
48
GETTING READY
• The Auto Power Off and Sleep features are disabled
in the following cases.
Using the On-screen Menus
Pressing [MENU] displays menus on the monitor screen
that you can use to perform various operations. The menu
that appears depends on whether you are in a REC mode
or the PLAY mode. The following shows an example menu
procedure in a REC mode.
— When the camera is connected to a computer or
some other device
— While a slideshow is in progress
— While playing back a voice recording file
— While a movie is being recorded
— While playing back a movie
Power button
1. Press the power
button or [ ] (REC).
• If you want to enter the
PLAY mode instead,
press [
] (PLAY).
[
] [
]
Download from Www.Somanuals.com. All Manuals Search And Download.
49
GETTING READY
Selection cursor (indicates
the currently selected item)
G Menu Screen Operations
2. Press [MENU].
When you want to do this:
Move between tabs
Do this:
Tab
[MENU]
Press [̇] and [̈].
Move from the tab to the
settings
Press [̄].
[̆]
[̈]
Move from the settings to
the tab
Press [̆].
[̇]
[̄]
Move between the settings
Press [̆] and [̄].
Display the options
available for a setting
Press [̈] or press [SET].
Press [̆] and [̄].
Select an option
[SET]
Settings
Apply the setting and exit
the menu screen
Press [SET].
Apply the setting and
return to tab selection
Press [̇].
Exit the menu screen
Press [MENU].
Download from Www.Somanuals.com. All Manuals Search And Download.
50
GETTING READY
3. Press [̇] or [̈] to select the tab you want,
and then press [SET] to move the selection
cursor from the tab to the settings.
6. Perform one of the following operations to
apply the setting you configured.
To do this:
Perform this key operation:
Press [SET].
Apply the setting and exit
the menu screen.
4. Use [̆] and [̄] to
select the feature
whose setting you
want to configure,
and then press [̈].
Apply the setting and
return to feature selection
in step 4.
Press [̇].
Apply the setting and
return to tab selection in
step 3.
1. Press [̇].
2. Use [̆] to move back up to
tab selection.
• Instead of pressing [̈],
you could also press
Example: To select the
[SET].
“Continuous”
IMPORTANT!
item.
• See “Menu Reference” on page 224 for more
information about menus.
• Entering the easy mode (page 61) changes display
contents to three menu items each, using larger size
characters. The easy mode also displays simple on-
screen help.
5. Use [̆] and [̄] to change the currently
selected setting.
Download from Www.Somanuals.com. All Manuals Search And Download.
51
GETTING READY
• A built-in backup battery retains the date and time
settings of the camera for about 48 hours if the
camera is not supplied with power. Date and time
settings will be cleared when the backup battery
goes dead. The following are the conditions when
power is not being supplied to the camera.
— When the batteries are dead or removed from the
camera
Configuring Display Language and Clock
Settings
Be sure to configure the following settings before using the
camera to record images.
• Display language
• Home city
• Date Style
— Disconnecting the AC adaptor while it is being
used to power the camera (without batteries
loaded)
• Date and time
Note that the current date and time settings are used by
the camera to generate the date and time that are stored
along with image data, etc.
• The date and time setting screen will appear on the
monitor screen the next time you turn on the camera
after the date and time settings have been cleared. If
this happens, reconfigure the date and time settings.
• If you make a mistake when setting the language or
clock with the following procedure, you will need to
use the camera’s menu to individually change the
language (page 171) or clock (page 168) settings.
• You will not be able to edit time data stored with
images that are recorded while the camera’s time
setting is wrong.
IMPORTANT!
• Recording images without configuring the clock
settings causes incorrect time information to be
registered. Be sure to configure the clock settings
before using the camera.
• Even if you configure date and time settings, the
date and time are not stamped into the images
themselves. Note, however, that you can specify
inclusion of the date inside of an image when printing
(page 190).
Download from Www.Somanuals.com. All Manuals Search And Download.
52
GETTING READY
3. Use [̆], [̄], [̇], and
[̈] to select the
To configure display language and clock
settings
geographical area
where you live, and
then press [SET].
1. Press the power button, [ ] (REC) or
[
] (PLAY) to turn on the camera.
2. Use [̆], [̄], [̇], and
[̈] to select the
4. Use [̆] and [̄] to
select the name of the
city where you live,
and then press [SET].
language you want,
and then press [SET].
: Japanese
English
: English
Français : French
Deutsch : German
Español : Spanish
5. Use [̆] and [̄] to select the summer time
(DST) setting you want, and then press [SET].
Italiano
Português : Portuguese
: Chinese (Complex)
: Italian
When you want to do this:
Select this setting:
Keep time using summer time
(Daylight Saving Time)
On
Off
: Chinese (Simplified)
: Korean
Keep time using standard time
Download from Www.Somanuals.com. All Manuals Search And Download.
53
GETTING READY
6. Use [̆] and [̄] to
select the date format
setting you want, and
then press [SET].
7. Set the current date
and the time.
Example: December 24, 2005
To do this:
Do this:
Change the setting at the current
cursor location
To display the date like this:
05/12/24
Select this format:
Press [̆] and [̄].
Press [̇] and [̈].
YY/MM/DD
DD/MM/YY
MM/DD/YY
Move the cursor between settings
24/12/05
Toggle between 12-hour and 24-
hour timekeeping
Press [DISP].
12/24/05
8. Press [SET] to register the settings and exit
the setting screen.
Download from Www.Somanuals.com. All Manuals Search And Download.
54
BASIC IMAGE RECORDING
This section describes the basic procedure for recording an
image.
•
•
(Snapshot mode)
Use this mode to record still images. This is the mode you
should normally use for image recording.
(BEST SHOT mode)
Recording an Image
This mode makes camera setup as easy as selecting the
applicable sample scene. Select one of the BEST SHOT
scenes and the camera automatically configures itself
with the setup for that scene (page 98).
Specifying the Recording Mode
Your CASIO digital camera has eight recording modes,
each of which is described below. Before recording an
image, use the mode dial to select the recording mode that
suits the type of image you are trying to record.
•
•
(easy mode)
This mode eliminates troublesome setups (page 61) .
(Aperture Priority AE mode)
In this mode, you select the aperture, and other settings
are adjusted accordingly (page 92).
Snapshot mode
BEST SHOT mode
easy mode
•
•
(Shutter Speed Priority AE mode)
In this mode, you select the shutter speed, and other
settings are adjusted accordingly (page 94).
Aperture Priority AE mode
Shutter Speed Priority AE
mode
(Manual Exposure mode)
Manual Exposure mode
This mode gives you total control over aperture and
shutter speed settings (page 95).
Voice Recording mode
Movie mode
Mode dial
•
•
(Voice Recording mode)
Use this mode to record audio only (page 114).
(Movie mode)
Use this mode to record movies (page 109).
Download from Www.Somanuals.com. All Manuals Search And Download.
55
BASIC IMAGE RECORDING
NOTE
Snapshot mode icon
Aiming the Camera
Use both hands to hold the camera still when shooting an
image. Holding the camera with one hand increases the
chance of movement, which can blur your images.
• The icon of the currently
selected recording mode
(like
for the Snapshot
mode) is displayed on the
monitor screen.
• Horizontal
Hold the camera
still in both
hands, with your
arms firmly
against your
sides.
• Vertical
When holding
the camera
vertically, make
sure that the
flash is above
the lens. Hold
the camera still
with both hands.
Download from Www.Somanuals.com. All Manuals Search And Download.
56
BASIC IMAGE RECORDING
IMPORTANT!
Recording an Image (Snapshot Mode)
• Make sure your fingers and the strap do not block
the flash, microphone, self-timer lamp or lens.
Your camera automatically adjusts shutter speed in
accordance with the brightness of the subject. Images you
record are stored in the camera’s built-in memory, or to a
memory card if you have one loaded in the camera.
• When an optionally available SD memory card or
MultiMediaCard (MMC) is loaded in the camera, images
are stored on the card (page 175).
Self-timer lamp
Flash
Microphone
After purchasing a memory card, be sure to load it into
the camera and format it before trying to use it (page
178).
Lens
NOTE
• Moving the camera as you press the shutter button
or while the Auto Focus operation is being performed
(when you press the shutter button half way) can
cause blurring of the image. Press the shutter button
carefully, taking care to avoid camera movement.
This is especially important when available lighting is
low, which slows down the shutter speed.
Download from Www.Somanuals.com. All Manuals Search And Download.
57
BASIC IMAGE RECORDING
Snapshot mode icon
1. Press the power button or [ ] (REC) to turn
on the camera.
2. Align the mode dial
with “ ” (Snapshot
mode) (page 55).
Power button
[
]
• The
(Snapshot
mode) icon is displayed
on the monitor screen
while the Snapshot
mode is selected.
Focus frame
• This causes an image or a message to appear on
the monitor screen, and then enters the currently
selected recording mode.
3. Compose the image on the monitor screen so
the main subject is within the focus frame.
• The focusing range of the camera depends on focus
mode you are using (page 79).
• If the camera is in the PLAY mode when it turns on,
the message “There are no files.” will appear if you
do not have any images stored in memory yet. In
• You can compose images using either the monitor
screen or the optical viewfinder (page 64).
addition, the
display. If this happens, press [
the currently selected recording mode.
icon will be visible at the top of the
] (REC) to enter
• When using the optical viewfinder to compose
images, you can use [DISP] to turn off the monitor
screen and conserve battery power.
Download from Www.Somanuals.com. All Manuals Search And Download.
58
BASIC IMAGE RECORDING
G Green Operation Lamp and Focus Frame Operation
4. Press the shutter button half
way to focus the image.
When you see this:
It means this:
• When you press the shutter
button half way, the camera’s
Auto Focus feature automatically
focuses the image, and displays
the shutter speed value, the
aperture value, and the ISO
sensitivity.
Green focus frame
Green operation lamp
The image is in focus.
Red focus frame
Flashing green operation lamp
The image is not in focus.
Shutter button
• The monitor screen uses various indicators and
icons to keep you informed of the camera’s status.
Green operation lamp
• You can tell whether
the image is focused
by observing the
focus frame and the
green operation
lamp.
Continuous
Shutter mode
Self-timer
REC modes
White balance
Metering mode indicator
Focus mode
Memory capacity
(Snapshots)
Flash
mode
Image quality
(Snapshots)
Image size
(Snapshots)
EV shift
Date and time
ISO sensitivity
Aperture value*1
Shutter speed value*2
Download from Www.Somanuals.com. All Manuals Search And Download.
59
B
BASIC IMAGE RECORDING
*1 The size of the opening (aperture) that allows light
passing through the lens to reach the CCD. A larger
aperture value indicates a smaller opening for light to
pass through. The camera adjusts this setting
automatically.
*2 The amount of time the shutter remains open, allowing
light passing through the lens to reach the CCD. A
larger shutter speed value indicates that the shutter
remains open longer, which means more light reaches
the CCD. The camera adjusts this setting automatically.
IMPORTANT!
• When the “REC” tab’s “Quick Shutter” setting is
turned on (page 81), the camera immediately records
the image without waiting for Auto Focus to be
performed when you press the shutter release all the
way down without pausing. This helps to ensure that
you are able to capture exactly the moment you
want.
5. After making sure that the
image is focused properly,
press the shutter button the
rest of the way down to
record.
Shutter button
• The number of images you can
record depends on the image
size and the image quality setting
you are using
(pages 77, 78, 238).
Download from Www.Somanuals.com. All Manuals Search And Download.
60
BASIC IMAGE RECORDING
I Using the easy Mode Menu
Using the easy Mode
In the easy mode, menu display is limited to flash, self-
timer, and image size settings. All other settings are fixed
automatically at preset optimum values.
The easy mode eliminates troublesome setups. This mode
is recommended for those who are new to digital imaging.
1. In a REC mode, align the mode dial with “
”
1. Press [MENU].
(page 55).
• The easy menu
displays larger text than
other mode menus.
• This enters the easy mode and causes “
” to
appear on the monitor screen.
2. Compose the image on the monitor screen so
the subject is within the focus frame.
3. Press the shutter button half way to focus the
image.
2. Use [̆] and [̄] to select the menu item you
want, and then press [SET].
• The focus frame will turn green and green operation
lamp will light when focusing is complete.
• On-screen pop-up help text provides a brief
explanation of each setting.
4. After making sure that the image is focused
properly, press the shutter button the rest of
the way down to record.
3. Use [̆] and [̄] to select the setting you
want, and then press [SET].
Download from Www.Somanuals.com. All Manuals Search And Download.
61
BASIC IMAGE RECORDING
Menu Item:
Flash
Available Settings:
Recording Precautions
(Auto Flash) /
(Flash Off)
(Flash On) /
I Recording Precautions
• Never open the battery cover while the green operation
lamp is flashing. Doing so not only causes the current
image to be lost, it can also corrupt images already stored
in file memory and even lead to malfunction of the
camera.
Self-timer
(10-second self-timer) / Off
5M / 3M / VGA
Image Size
• Underlined settings indicate initial defaults.
• Never remove the memory card while an image is being
recorded to the memory card.
4. After making the menu settings you want,
• Fluorescent lighting actually flickers at a frequency that
cannot be detected by the human eye. When using the
camera indoors under such lighting, you may experience
some brightness or color problems with recorded images.
• When “Auto” is selected for the ISO sensitivity setting
(page 123), the camera automatically adjusts its
sensitivity in accordance with the brightness of the
subject. This can cause some digital noise (graininess) to
appear in images of relatively dark subjects.
select “Exit Menu” and then press [SET].
• See the following sections for full details about each
setting.
— Using the Flash (page 69)
— Using the Self-timer (page 74)
— Specifying Image Size (page 77)
Download from Www.Somanuals.com. All Manuals Search And Download.
62
BASIC IMAGE RECORDING
• When recording a dimly lit subject while “Auto” is selected
for the ISO sensitivity setting (page 123), the camera
increases sensitivity and uses a faster shutter speed.
Because of this, you need to guard against camera
ꢀ About Auto Focus
• Proper focus may be difficult or even impossible when
shooting the following types of subjects.
— Solid color walls or subjects with little contrast
— Strongly backlit subjects
movement if you have flash turned off
(page 69).
• Bright light shining on the lens can cause images to
appear “washed out”. This tends to happen when
recording images outdoors in bright sunlight. To protect
against this, use your free hand to shade the lens from
the light.
— Very shiny objects
— Venetian blinds or other horizontally repeating patterns
— Multiple subjects that are varying distances from the
camera
— Subjects in poorly lit areas
— Moving subjects
— Subjects outside the shooting range of the camera
• Proper focus may also be difficult or impossible if the
camera is moving.
• Note that a green operation lamp and focus frame do not
necessarily guarantee that the resulting image will be in
focus.
• If Auto Focus does not produce the results you want for
some reason, try using focus lock (page 86) or manual
focus (page 85).
Download from Www.Somanuals.com. All Manuals Search And Download.
63
C
BASIC IMAGE RECORDING
I About the REC Mode Monitor Screen
Using the Optical Viewfinder
• The image shown on the monitor screen in a REC mode
is a simplified image for composing purposes. The actual
image is recorded in accordance with the image quality
setting currently selected on your camera. The image
saved in file memory has much better resolution and
detail than the REC mode monitor screen image.
• Certain levels of subject brightness can cause the
response of the REC mode monitor screen to slow down,
which causes some digital noise (graininess) in the
monitor screen image.
• Very bright light inside of an image can cause a vertical
band to appear in the monitor screen image. This is a
CCD phenomenon known as “vertical smear”, and does
not indicate malfunction of the camera. Note that vertical
smear is not recorded with the image in the case of a
snapshot, but it is recorded in the case of a movie (page
107).
You can conserve battery power by turning off the
camera’s monitor screen (page 35) and using the optical
viewfinder to compose images. The optical viewfinder also
comes in handy when shooting in areas where the monitor
screen is difficult to view because available lighting is dim,
etc.
IMPORTANT!
• The visible area framed by the viewfinder shows the
image that would be recorded at a distance of about
one meter (3.3˝). When recording a subject that is
closer to you than one meter, the recorded image will
be lower than what you can see inside the viewfinder
area.
Optical viewfinder
Area recorded at
Area visible in
distances less than the viewfinder
one meter (3.3˝)
Download from Www.Somanuals.com. All Manuals Search And Download.
64
BASIC IMAGE RECORDING
• Since the monitor screen shows exactly what will be
recorded, always use it for composing images in the
Macro and Manual Focus modes.
Using Zoom
Your camera is equipped with two types of zoom: optical
zoom and digital zoom. Normally, the camera automatically
switches over to digital zoom after you reach the maximum
limit for optical zoom. You can, however, configure the
camera to disable digital zoom, if you want.
Optical Zoom
The optical zoom range is 1X to 3X.
Zoom controller
1. In a REC mode, move
the zoom controller left
or right to zoom.
• Moving the zoom
controller as far as it
goes in either direction
will zoom at high speed.
Move the zoom
To do this:
controller in this
direction:
Zoom out for a wider view
(main subject becomes smaller)
(Wide Angle)
(Telephoto)
Zoom in for a closer view (main
subject becomes larger)
Download from Www.Somanuals.com. All Manuals Search And Download.
65
BASIC IMAGE RECORDING
NOTE
• The optical zoom factor also affects the lens
aperture.
• Use of a tripod is recommended to protect against
hand movement when using the telephoto setting
(zoom in).
• Whenever you perform an optical zoom operation
while recording with the Auto Focus mode, Macro
mode, or manual focus, a value will appear on the
monitor screen to tell you the focusing range (pages
80, 83, 85).
Zoom out
Zoom in
2. Compose the image, and then press the
shutter button.
• Optical zoom is disabled during movie recording.
Digital zoom only is available. Make sure you select
the optical zoom setting you want to use before you
press the shutter button to start movie recording
(page 107).
Download from Www.Somanuals.com. All Manuals Search And Download.
66
BASIC IMAGE RECORDING
I To record an image using digital zoom
Digital Zoom
Digital zoom digitally enlarges the part of the image at the
center of the image screen. The range of digital zoom is 3X
to 12X (in combination with optical zoom).
Digital zoom indicator
1. In a REC mode, hold
the zoom controller
towards
(telephoto) side.
IMPORTANT!
• This causes the zoom
indicator to appear on
the display.
• When you perform a digital zoom operation, the
camera manipulates the image data to enlarge the
center of the image. Unlike optical zoom, an image
enlarged with digital zoom appears coarser than the
original.
Zoom indicator
2. When the zoom pointer reaches the optical/
digital zoom switch over point, it will stop.
Digital
Zoom range
Optical Zoom range
1X
3X
12X
Zoom pointer
Optical/digital zoom switch over point
• The above shows what the zoom indicator looks like
when digital zoom is turned on (page 68). The digital
zoom range is not displayed when digital zoom is
turned off.
Download from Www.Somanuals.com. All Manuals Search And Download.
67
BASIC IMAGE RECORDING
3. Release the zoom controller momentarily, and
I To turn digital zoom on and off
then slide it towards
(telephoto) side again
to move the zoom pointer into the digital
zoom range.
1. In a REC mode, press [MENU].
2. Use [̇] and [̈] to select the “REC” tab.
• The zoom pointer will also stop when you move the
pointer back to the switch over point to re-enter the
optical zoom range. Release the zoom controller and
3. Use [̆] and [̄] to select “Digital Zoom”, and
then press [̈].
then slide it towards
(wide angle) side again to
move into the optical zoom range.
4. Use [̆] and [̄] to select the setting you
want, and then press [SET].
4. Compose the image, and then press the
shutter button.
To do this:
Select this setting:
Turn on digital zoom
Turn off digital zoom
On
Off
• Only the optical zoom range is displayed in the zoom
indicator when digital zoom is turned off.
Download from Www.Somanuals.com. All Manuals Search And Download.
68
BASIC IMAGE RECORDING
To do this:
Select this setting:
Using the Flash
Have the flash fire automatically when
required (Auto Flash)*
Perform the following steps to select the flash mode you
want to use.
• The approximate effective range of the flash is shown
below.
Turn off the flash (Flash Off)
Always fire the flash (Flash On)
Fire a pre-flash followed by image
recording with flash, reducing the
chance of red-eye in the image (Red-
eye reduction)
In this case, the flash fires automatically
when required
Wide Angle Optical Zoom:
Approximately 0.4 to 3.1 meters
(1.3´ to 10.2´) (ISO Sensitivity: Auto)
Telephoto Optical Zoom:
Approximately 0.4 to 1.8 meters
(1.3´ to 5.9´) (ISO Sensitivity: Auto)
* Depends on zoom factor.
*
appears momentarily when you select Auto as
the flash mode, and then disappears.
1. In a REC mode, press [̄] (
).
2. Press the shutter button to record the image.
• Each press of [̄] (
) cycles through the flash
mode settings described below on the monitor
screen.
Flash mode indicator
[̄] (
)
Download from Www.Somanuals.com. All Manuals Search And Download.
69
BASIC IMAGE RECORDING
IMPORTANT!
I Flash On
• The flash unit of this camera fires a number of times
when you record an image. The initial flashes are
pre-flashes, which the camera uses to obtain
information that it uses for exposure settings. The
final flash is for recording. Make sure that you keep
the camera still until the shutter releases.
Select
(Flash On) as the flash mode when backlighting
causes your subject to appear dark, even though there is
enough light to keep the flash from firing automatically.
This will cause the flash to fire and illuminate your subject
whenever you press the shutter button (daylight synchro
flash).
• Using the flash while “Auto” is selected for the ISO
Sensitivity setting increases sensitivity, which can
cause large amounts of digital noise to appear in the
image. You can reduce digital noise by using a lower
ISO Sensitivity setting. Note, however, that this also
has the effect of shortening the flash range (the
range that is covered by the light from the flash)
(page 123).
I About Red-eye Reduction
Using the flash to record at night or in a dimly lit room can
cause red spots inside the eyes of people who are in the
image. This happens because the light from the flash
reflects off of the retina of the eye.
Download from Www.Somanuals.com. All Manuals Search And Download.
70
BASIC IMAGE RECORDING
IMPORTANT!
Flash Unit Status
You can find out the current flash unit status by pressing
the shutter button half way and checking the monitor
screen and red operation lamp.
Note the following important points when using red-
eye reduction.
• Red-eye reduction does not work unless the people
in the image are looking directly at the camera during
the pre-flash. Before pressing the shutter button, call
out to the subjects so they all look at the camera
while the pre-flash operation is performed.
• Red-eye reduction may not work very well if the
subjects are located far away from the camera.
Red operation lamp*
The
indicator is also shown
on the monitor screen when the
flash unit is ready to fire.
* Red operation lamp
When the red operation
lamp is this:
It means this:
Flashing
Lit
Flash unit is charging
Flash unit is ready to fire
Download from Www.Somanuals.com. All Manuals Search And Download.
71
BASIC IMAGE RECORDING
Changing the Flash Intensity Setting
Using Flash Assist
Perform the following steps to change the flash intensity
setting.
Recording a subject that is outside the flash range can
cause the subject to appear dark in the resulting image,
because not enough of the flash reaches the subject. When
this happens, you can use flash assist to correct the
brightness of the recorded subject, so it appears as if the
flash illumination was sufficient.
1. In a REC mode, press [MENU].
2. Use [̇] and [̈] to select the “Quality” tab.
3. Use [̆] and [̄] to select “Flash Intensity”,
and then press [̈].
4. Use [̆] and [̄] to select the setting you
want, and then press [SET].
To make flash intensity:
Stronger
Select this setting:
Flash assist used
Flash assist not used
+2
+1
0
1. In a REC mode, press [MENU].
Normal
–1
–2
2. Use [̇] and [̈] to select the “Quality” tab.
Weaker
3. Use [̆] and [̄] to select “Flash Assist”, and
then press [̈].
IMPORTANT!
• Flash intensity may not change if the subject is too
far or too close to the camera.
Download from Www.Somanuals.com. All Manuals Search And Download.
72
BASIC IMAGE RECORDING
Flash
4. Use [̆] and [̄] to select “Auto”, and then
I Flash Precautions
press [SET].
• Take care that your fingers
do not block the flash when
you hold the camera.
• Selecting “Off” disables flash assist.
Covering the flash with your
finger can greatly reduce its
effectiveness.
IMPORTANT!
• Flash assist may not produce the desired result for
some types of subjects.
• Flash assist may have little effect on your image if
you changed any of the following settings when you
recorded it.
— Flash intensity (page 72)
— Exposure compensation (EV shift) (page 87)
— ISO sensitivity (page 123)
— Contrast (page 127)
• Using flash assist can cause an increase of digital
noise in recorded images.
• You may not be able to achieve the desired results using
the flash if the subject is too close or too far away.
• The flash takes anywhere from a few seconds to as long
as 10 seconds to attain full charge after being fired. The
actual time required depends on the battery level,
temperature, and other conditions.
• The flash does not fire during movie recording.
• The flash unit may not be able to charge when camera
battery power is low. If this happens, the flash will not fire
properly and you will not be able to obtain the desired
exposure. Be sure to replace the camera’s batteries as
soon as possible when power goes low.
Download from Www.Somanuals.com. All Manuals Search And Download.
73
BASIC IMAGE RECORDING
• When the flash is turned off (
), mount the camera on a
Using the Self-timer
tripod to record images in an area where available lighting
is dim. Recording images under dim lighting without the
flash can cause digital noise, which makes images
appear coarse.
The self-timer lets you select either a 2-second or 10-
second delay of the shutter release after you press the
shutter button. A Triple Self-timer feature lets you perform
three consecutive self-timer operations to record three
images.
• When red-eye reduction (
) is selected, flash intensity
is adjusted automatically in accordance with the
exposure. The flash may not fire at all when the subject is
brightly lit.
• Using flash in combination with another light source
(daylight, fluorescent light, etc.) can result in abnormal
image colors.
1. In a REC mode, press [MENU].
2. Use [̇] and [̈] to select the “REC” tab.
3. Use [̆] and [̄] to select “Self-timer”, and
then press [̈].
4. Use [̆] and [̄] to select the self-timer type
you want to use, and then press [SET].
• Selecting “Off” in step 4 disables the self-timer.
Download from Www.Somanuals.com. All Manuals Search And Download.
74
BASIC IMAGE RECORDING
1. The camera performs a 10-second countdown
and then records the first image.
To do this:
Select this setting:
10 sec
Specify a 10-second self-timer
Specify a 2-second self-timer
Specify Triple Self-timer
Disable the self-timer
10
s
2. The camera prepares to record the next image.
The amount of time required for preparation
depends on the camera’s current “Size” and
“Quality” settings, the type of memory (built-in or
card) you are using for image storage, and
whether or not the flash is charging.
2 sec
X3
2
s
x3
Off
3. After preparation is complete, the indicator “1sec”
appears on the monitor screen, and another
image is recorded one second later.
• This causes an
indicator identifying the
selected self-timer type
to appear on the
4. Steps 2 and 3 are repeated once more to record
the third image.
monitor screen.
• With the Triple Self-timer,
the camera records a
series of three images in
the sequence described
below.
Download from Www.Somanuals.com. All Manuals Search And Download.
75
BASIC IMAGE RECORDING
Self-timer lamp
NOTE
5. Press the shutter
button to record the
image.
• The “2 sec” self-timer setting is best when shooting
with a slow shutter speed, because it helps to avoid
blurring of images due to hand movement.
• The following functions are not available for use in
combination with the Triple Self-timer.
• When you press the
shutter button, the self-
timer lamp flashes and
the shutter releases
after the self-timer
reaches the end of its
countdown (about 10
seconds or two
Business Shot, movie recording functions
seconds).
• You can interrupt an ongoing self-timer countdown
by pressing the shutter button while the self-timer
lamp is flashing.
Download from Www.Somanuals.com. All Manuals Search And Download.
76
BASIC IMAGE RECORDING
Image Size
Print Size
Specifying Image Size
×
5M*
2560 1920 A3 Print
Larger
“Image size” is the size of the image, expressed as the
number of vertical and horizontal pixels. A “pixel” is one of
the many tiny dots that make up the image. More pixels
provide finer detail when an image is printed, but a higher
pixel count also causes the image’s file size to be larger.
You can select an image size to suit your needs for greater
detail or smaller file size.
×
5M
(3:2) (3:2)
2560 1712 A3 Print (3:2 horizontal-to-
vertical ratio)
2304 1728 A4 Print
×
4M
3M
2M
×
2048 1536 A4 Print
×
×
1600 1200 3.5˝ 5˝ Print
E-mail (optimum size when
attaching image to e-mail)
×
VGA 640 480
Smaller
• Note that this setting is valid for snapshots only. For
information about movie image size, see page 108.
* “M” stands for “Mega.”
1. In a REC mode, press [MENU].
• The above print sizes are all approximate values when
printing at a resolution of 200 dpi (dots per inch). Use a
larger setting when you want to print at a higher
resolution or when you plan to produce a larger size print.
• In order to obtain the level of resolution for which your
camera is designed, recording at a maximum image size
(5M) is recommended. Use a smaller image size when
you want to conserve memory capacity.
2. Use [̇] and [̈] to select the “Quality” tab.
3. Use [̆] and [̄] to select “Size”, and then
press [̈].
4. Use [̆] and [̄] to select the setting you
×
• Selecting the “2560 1712 (3:2)” image size records
want, and then press [SET].
images with a 3:2 (horizontal:vertical) aspect ratio, which
is optimal for printing on photographic paper with an
aspect ratio of 3:2.
• When selecting the image size, the image size value
(pixels) will alternate on the display with a
corresponding print size. The print size indicates the
optimum paper size when you print an image that is
the image size you select.
Download from Www.Somanuals.com. All Manuals Search And Download.
77
C
BASIC IMAGE RECORDING
To get this:
Select this setting:
Fine
Specifying Image Quality
High image quality, large file
size
Higher
Quality
Compressing an image before storage can cause a
deterioration of its quality. The more an image is
compressed, the greater the loss of quality. The image
quality setting specifies the compression ratio to be used
when an image is stored in memory. You can select an
image quality setting to suit your needs for higher quality or
smaller file size.
Normal image quality and
normal file size
Normal
Lower
Quality
Low image quality, small file
size
Economy
IMPORTANT!
• Note that this setting is valid for snapshots only. For
information about movie image quality, see page 108.
• Actual file size depends on the type of image you
record. This means that the remaining image
capacity noted on the monitor screen may not be
exactly accurate (pages 31, 238).
1. In a REC mode, press [MENU].
2. Use [̇] and [̈] to select the “Quality” tab.
3. Use [̆] and [̄] to select “
then press [̈].
Quality”, and
4. Use [̆] and [̄] to select the setting you
want, and then press [SET].
Download from Www.Somanuals.com. All Manuals Search And Download.
78
OTHER RECORDING FUNCTIONS
To set up the camera to do this:
Select this setting:
Selecting the Focus Mode
Focus automatically (Auto Focus)
Perform close-up focus (Macro)
Fix the focal distance (Pan Focus)
Perform infinity focus (Infinity)
Focus manually (Manual Focus)
You can select one of five different focus modes: Auto
Focus, Macro, Pan Focus, Infinity, and Manual Focus.
[̆] (
)
1. In a REC mode, press [̆]
(
).
• Each press of [̆] (
)
cycles thorough the focus
mode settings in the
sequence shown below.
Focus mode indicator
Download from Www.Somanuals.com. All Manuals Search And Download.
79
OTHER RECORDING FUNCTIONS
Green operation lamp
Using Auto Focus
As its name suggests, Auto Focus focuses the image
automatically. The automatic focus operation starts when
you press the shutter button down half way. The following
is the Auto Focus range.
Range: 40cm to ∞ (1.3´ to ∞)
• Using optical zoom causes the above range to change.
Focus frame
When you see this:
It means this:
1. Press [̆] (
) to cycle through the focus
mode settings until “ ” is shown as the
Green focus frame
Green operation lamp
The image is focused.
focus mode indicator.
Red focus frame
Flashing green operation lamp
The image is not
focused.
• “
” appears momentarily when you select auto
focus, and then disappears.
2. Compose the image so the main subject is
within the focus frame, and then press the
shutter button half way.
3. Press the shutter button the rest of the way to
record the image.
• You can tell whether the image is focused by
observing the focus frame and the green operation
lamp.
Download from Www.Somanuals.com. All Manuals Search And Download.
80
OTHER RECORDING FUNCTIONS
NOTE
I Quick Shutter
• When proper focusing is not possible because the
subject is closer than the Auto Focus range, the
camera automatically switches to the Macro mode
range (page 83).
• Whenever you perform an optical zoom operation
(page 65) while recording with Auto Focus, a value
will appear on the monitor screen as shown below to
tell you the focusing range.
When Quick Shutter is turned on, the camera immediately
records the image without waiting for Auto Focus to be
performed when you press the shutter release all the way
down. This helps to avoid missing a special moment while
you wait for the camera to Auto Focus.
1. In a REC mode, press [MENU].
Example: AF ȚȚcm - ∞
* ȚȚ will be replaced by the actual focusing range value.
2. Select the “REC” tab, select “Quick Shutter”,
and then press [̈].
3. Use [̆] and [̄] to select the setting you
want, and then press [SET].
To do this:
Select this setting:
Turn on Quick Shutter
Turn off Quick Shutter
On
Off
Download from Www.Somanuals.com. All Manuals Search And Download.
81
OTHER RECORDING FUNCTIONS
I Specifying the Auto Focus Area
For this type of Auto Focus area:
Select this:
Spot
Very limited range in the center of the
screen
• This setting works well with focus lock
(page 86).
You can use the following procedure to change the Auto
Focus area used in the Auto Focus mode and the Macro
mode. Note that the configuration of the focus frame
changes in accordance with the Auto Focus area you
select.
Automatic selection of the focus area where
the subject closest to the camera is located
• With this setting, a wide focus frame,
which contains nine focus points, appears
on the monitor screen first. When you
press the shutter button half way, the
camera automatically selects the focus
point where the subject closest to the
camera is located, and a focus frame
appears at that point.
1. In a REC mode, press [MENU].
Multi
2. On the “REC” tab, select “AF Area”, and then
press [̈].
3. Use [̆] and [̄] to select the Auto Focus area
• This setting works well for group photos.
you want, and then press [SET].
•
Spot
•
Multi
Focus frame
Focus frame
Download from Www.Somanuals.com. All Manuals Search And Download.
82
OTHER RECORDING FUNCTIONS
NOTE
Using the Macro Mode
• When the Macro mode cannot focus properly
because the subject is too far away, the camera
automatically switches to the Auto Focus range
(page 80).
Use the Macro mode when you need to focus on close up
subjects. The following shows the approximate focus range
in the Macro mode.
Range: 6cm to 50cm (2.4˝ to 19.7˝)
• Using optical zoom causes the above range to change.
• Whenever you perform an optical zoom operation
(page 65) while recording with the Macro mode, a
value will appear on the monitor screen as shown
below to tell you the focusing range.
Example: ȚȚcm - ȚȚcm
* ȚȚ will be replaced by the actual focusing range value.
1. Press [̆] (
) to cycle through the focus
mode settings until “ ” is shown as the
focus mode indicator.
IMPORTANT!
2. Press the shutter button to record the image.
• Use of the flash along with the Macro mode can
cause the light of the flash to become blocked, which
can produce unwanted lens shadows in your image.
• The focus and image recording operations are
identical to those in the Auto Focus mode.
Download from Www.Somanuals.com. All Manuals Search And Download.
83
OTHER RECORDING FUNCTIONS
Using Pan Focus
Using the Infinity Mode
Pan Focus comes in handy when recording under
conditions where Auto Focus is difficult for some reason, or
in cases where Auto Focus operation noise is too
noticeable in the movie audio.
The Infinity mode fixes focus at infinity (∞). Use this mode
when recording scenery and other faraway images.
1. Press [̆] (
) to cycle through the focus
mode settings until “ ” is shown as the
1. Press [̆] (
) to cycle through the focus
focus mode indicator.
mode settings until “ ” is shown as the
focus mode indicator.
2. Press the shutter button to record the image.
2. Press the shutter button to record the image.
NOTE
• If you press the shutter button half way, the focus
distance will appear on the monitor screen.
Example: ȚȚm - ȚȚm
* ȚȚ will be replaced by the actual focusing range value.
Download from Www.Somanuals.com. All Manuals Search And Download.
84
OTHER RECORDING FUNCTIONS
2. While watching the
image on the monitor
screen, use [̇] and
[̈] to focus.
Using Manual Focus
With the Manual Focus mode, you can adjust the focus of
an image manually. The following shows focus range in the
Manual Focus mode.
Optical Zoom Factor
Approximate Focus Range
6cm (2.4˝) to infinity (∞)
40cm (15.7˝) to infinity (∞)
1X
3X
Manual focus position
Do this:
• Using optical zoom causes the above range to change.
To do this:
Focus in on the subject
Focus out on the subject
Press [̇].
Press [̈].
1. Press [̆] (
) to
cycle through the
focus mode settings
until “ ” is shown
as the focus mode
indicator.
• Pressing [̇] or [̈] causes the area inside of the
boundary displayed in step 1 to fill the monitor
screen momentarily to aid in focus. The normal
image will reappear a short while later.
• At this point, a
boundary also appears
on the display,
3. Press the shutter button to record the image.
Boundary
indicating the part of the
image that will be used
for manual focus.
Download from Www.Somanuals.com. All Manuals Search And Download.
85
OTHER RECORDING FUNCTIONS
NOTE
Using Focus Lock
Focus lock is a technique you can use to focus on a subject
that is not located within the focus frame when you record
an image. You can use focus lock in the Auto Focus mode
• Whenever you perform an optical zoom operation
(page 65) while recording with manual focus, a value
will appear on the monitor screen as shown below to
tell you the focusing range.
Example: MF ȚȚcm - ∞
* ȚȚ will be replaced by the actual focusing range value.
and the Macro mode (
).
Main subject
1. Using the monitor
screen, compose the
image so the main
subject is within the
focus frame, and then
press the shutter
button half way.
• This locks the focus on
the subject that is
currently within the
focus frame.
Focus frame
Download from Www.Somanuals.com. All Manuals Search And Download.
86
OTHER RECORDING FUNCTIONS
2. Keeping the shutter
button pressed half
way down, re-
Exposure Compensation (EV Shift)
Exposure compensation lets you change the exposure
setting (EV value) manually to adjust for the lighting of your
subject. This feature helps to achieve better results when
recording a backlit subject, a strongly lit subject indoors, or
a subject that is against a dark background.
compose the image
as you like.
Main subject
EV Shift Range: –2.0EV to +2.0EV
Steps: 1/3EV
3. When the image is composed the way you
want, press the shutter button the rest of the
way to record it.
1. In a REC mode, press [MENU].
• The focus and image recording operations are
identical to those in the Auto Focus mode.
2. Select the “Quality”
tab, select “EV Shift”,
and then press [̈].
NOTE
• Locking the focus also locks the exposure.
Exposure compensation
value
Download from Www.Somanuals.com. All Manuals Search And Download.
87
OTHER RECORDING FUNCTIONS
3. Use [̆] and [̄] to change the exposure
4. Press the shutter button to record the image.
IMPORTANT!
compensation value, and then press [SET].
• Pressing [SET] registers the displayed value.
• When shooting under very dark or very bright
conditions, you may not be able to obtain satisfactory
results even after performing exposure
compensation.
[̆] : Increases the EV value. A higher EV value is best
used for light-colored subjects and backlight
subjects.
NOTE
• Performing an EV shift operation while using multi-
pattern metering (page 124) will cause the metering
mode to switch automatically to center weighted
metering. Returning the EV shift value to 0.0 causes
the metering mode to change back to multi-pattern
metering.
• You can use key customization (page 119) to
configure the camera to perform exposure
compensation whenever you press [̇] or [̈] while in
a REC mode. This comes in handy when adjusting
exposure compensation while viewing the on-screen
histogram (page 115).
[̄] : Decreases the EV value. A lower EV value is best
for dark-color subjects and for shooting outdoors
on a clear day.
• To cancel EV Shift, adjust the value until it becomes
0.0.
Download from Www.Somanuals.com. All Manuals Search And Download.
88
OTHER RECORDING FUNCTIONS
3. Use [̆] and [̄] to select the setting you
Adjusting White Balance
want, and then press [SET].
The wavelengths of the light produced by various light
sources (daylight, light bulb, etc.) can affect the color of a
subject when it is recorded. White balance lets you make
adjustments to compensate for different lighting types, so
the colors of an image appear more natural.
When shooting under these conditions: Select this setting:
Normal conditions
Auto
Outdoor daylight on a clear day
Outdoor daylight on an overcast or
rainy day, in the shade of a tree, etc.
1. In a REC mode, press [MENU].
In the shade of a building or any other
area where the color temperature is
high
2. Select the “Quality”
tab, select “White
Balance”, and then
press [̈].
Under white or daylight white
fluorescent light
(suppresses color fogging)
N
D
Under daylight fluorescent light
(suppresses color fogging)
Under incandescent lighting
Difficult lighting that requires manual
control (See “Configuring the White
Balance Setting Manually” (page 90).)
Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
89
B
OTHER RECORDING FUNCTIONS
NOTE
Configuring the White Balance Setting
Manually
Certain complex light sources or other environmental
conditions can make it impossible to obtain good results
when “Auto” or one of the fixed light source settings is
selected for white balance. Manual white balance lets you
configure the camera for a particular light source and other
conditions.
Note that you must perform manual white balance under
the same conditions you will be shooting under. Have a
sheet of white paper on hand before starting the following
procedure.
• When “Auto” is selected for the white balance
setting, the camera automatically determines the
white point of the subject. Certain subject colors and
light source conditions can cause problems when the
camera tries to determine the white point, which
makes proper white balance adjustment impossible.
When this happens, use daylight, cloudy, or one of
the other fixed white balance settings to specify the
type of lighting available.
• You can use the key customization feature (page
119) to configure the camera so the white balance
setting changes whenever you press [̇] or [̈] while
in a REC mode.
• If you have key customization configured to control
1. In a REC mode, press [MENU].
white balance, select “
Auto WB” to change the
AWB
white balance mode to auto.
2. Select a “Quality” tab, select “White
Balance”, and then press [̈].
Download from Www.Somanuals.com. All Manuals Search And Download.
90
OTHER RECORDING FUNCTIONS
• This starts the white balance adjustment procedure.
The message “Complete” appears on the monitor
screen after white balance adjustment is complete.
3. Use [̆] and [̄] to
select “Manual”.
• This causes the object
you last used to adjust
manual white balance to
appear on the monitor
screen. If you want to use
the same settings you
configured during a
5. Press [SET].
• This registers the white balance settings and returns
to the currently selected recording mode.
NOTE
previous manual white
balance setting
operation, skip step 4
and perform step 5.
• After you adjust white balance manually, the setting
remains in effect until you change it or until you turn
off the camera.
4. Point the camera at a white paper or similar
object under the lighting conditions for which
you want to set the white balance, and then
press the shutter button.
White paper
Download from Www.Somanuals.com. All Manuals Search And Download.
91
OTHER RECORDING FUNCTIONS
Wide Aperture
Small Aperture
Specifying the Exposure Mode
You can use the mode dial to select the exposure mode,
which controls the aperture and shutter speed settings
used during image recording.
A mode : Aperture Priority AE
S mode : Shutter Speed Priority AE
M mode : Manual Exposure
1. Align the mode dial
with “A” (Aperture
Priority).
Using Aperture Priority AE
When A mode (aperture priority AE) is selected as the
exposure mode, the camera adjusts the shutter speed
automatically in accordance with a fixed aperture value
specified by you. A wider aperture (a lower aperture value)
provides a shallow depth of field, while a small aperture (a
higher aperture value) provides a greater depth of field.
The shutter speed range in this mode is 1/2000 to 1
second.
Aperture value EV shift
Download from Www.Somanuals.com. All Manuals Search And Download.
92
B
OTHER RECORDING FUNCTIONS
2. Use [̆] and [̄] to select the aperture value
(page 33) in the exposure panel, and then use
[̇] and [̈] to change the setting.
3. Press the shutter button half way.
• This causes the camera to configure shutter speed
automatically in accordance with the aperture value
you selected. Then it focuses the image.
Wide
Small
Aperture value
*
• The shutter speed and aperture values on the
monitor screen will turn amber when you press the
shutter button half way if the image is over-exposed
or under-exposed.
F3.1 ‚ 4.4
Depth of Field
Shallow
Deep
* The above values are full wide angle optical zoom.
Aperture values are different at other optical zoom
settings.
4. When the image is focused, press the shutter
button all the way down to record.
• You could also use [̆] and [̄] to select “EV Shift”
here, and then use [̇] and [̈] to specify an
exposure compensation value (pages 33, 87).
•
If you are using manual focus (pages 33, 85), you can
also use [̆] and [̄] to select “FOCUS” (manual focus
adjustment), and then use [̇] and [̈] to focus
manually.
Download from Www.Somanuals.com. All Manuals Search And Download.
93
OTHER RECORDING FUNCTIONS
1. Align the mode dial
with “S” (Shutter
Speed Priority).
Using Shutter Speed Priority AE
When S mode (shutter speed priority AE) is selected as the
exposure mode, the camera adjusts the aperture
automatically in accordance with a fixed shutter speed
specified by you. You should specify a shutter speed in
accordance with how much your subject is moving.
Slow
Fast
Shutter speed
EV shift
2. Use [̆] and [̄] to select the shutter speed
value (page 33) in the exposure panel, and
then use [̇] and [̈] to change the setting.
Slow
60 seconds
Blurred
Fast
Shutter speed
Movement
1/2000 second
Stopped
• You could also use [̆] and [̄] to select “EV Shift”
here, and then use [̇] and [̈] to specify an
exposure compensation value (pages 33, 87).
• If you are using manual focus (pages 33, 85), you
can also use [̆] and [̄] to select “FOCUS” (manual
focus adjustment), and then use [̇] and [̈] to focus
manually.
Download from Www.Somanuals.com. All Manuals Search And Download.
94
OTHER RECORDING FUNCTIONS
3. Press the shutter button half way.
Setting Exposure Settings Manually
In the M mode (manual exposure), you can adjust shutter
speed and aperture manually.
• This causes the camera to configure the aperture
value automatically in accordance with the shutter
speed you selected. Then it focuses the image.
• The shutter speed and aperture values on the
monitor screen will turn amber when you press the
shutter button half way if the image is over-exposed
or under-exposed.
1. Align the mode dial
with “M” (Manual).
4. When the image is focused, press the shutter
button all the way down to record.
ISO sensitivity Aperture value
Shutter speed
2. Use [̆] and [̄] to select the aperture value
(page 33) in the exposure panel, and then use
[̇] and [̈] to change the setting.
Wide
Small
F3.1 ‚ 4.4
Deep
Aperture value*
Depth of Field
Shallow
* The above values are full wide angle optical zoom.
Aperture values are different at other optical zoom
settings.
Download from Www.Somanuals.com. All Manuals Search And Download.
95
OTHER RECORDING FUNCTIONS
3. Use [̆] and [̄] to select the shutter speed
value (page 33) in the exposure panel, and
then use [̇] and [̈] to change the setting.
Exposure Mode Recording Precautions
• You may not be able to achieve the brightness you want
when recording an image that is very dark or very bright.
If this happens, use the M mode (manual exposure) to
adjust the aperture or shutter speed manually.
• Using slow shutter speeds can cause digital noise
(graininess) to appear in the image. Because of this, the
camera automatically performs a digital noise reduction
process whenever the shutter speed is 1/8 second or
slower. The slower the shutter speed, the greater the
possibility that digital noise will be generated in an image.
Also note that the digital noise reduction process can
cause it to take longer to record each image.
Slow
60 seconds
Blurred
Fast
Shutter speed
Movement
1/2000 second
Stopped
• If you are using manual focus (pages 33, 85), you
can also use [̆] and [̄] to select “FOCUS” (manual
focus adjustment), and then use [̇] and [̈] to focus
manually.
4. Press the shutter button half way.
• At shutter speeds slower than 1/8 second, the brightness
of the recorded image may not be the same as the
brightness of the image that appears on the monitor
screen.
•
This causes the camera to adjust focus automatically.
5. When the image is focused, press the shutter
button all the way down to record.
Download from Www.Somanuals.com. All Manuals Search And Download.
96
OTHER RECORDING FUNCTIONS
IMPORTANT!
Recording Consecutive Images
(Continuous Shutter Mode)
You can configure the camera to record only a single
snapshot each time the shutter button is pressed, or to
keep recording as long as the shutter button remains
depressed (and there is enough memory available to store
the images).
• The speed of continuous shutter recording depends
on the type of memory card loaded in the camera.
When recording to built-in memory, continuous
shutter recording is relatively slow.
• Turning off the camera automatically turns off the
Continuous Shutter mode.
1. In a REC mode, press [MENU].
2. Select the “REC” tab, select “Continuous”,
and then press [̈].
3. Use [̆] and [̄] to select “On”, and then
press [SET].
• This causes “
” to appear on the monitor screen.
• With “Off”, the snapshots are recorded one at a time.
4. Press the shutter button to record.
• Recording continues as long as you keep the shutter
button depressed. Release the shutter button to stop
recording.
Download from Www.Somanuals.com. All Manuals Search And Download.
97
C
OTHER RECORDING FUNCTIONS
1. In a REC mode, align
the mode dial with
Using the BEST SHOT Mode
Selecting one of the BEST SHOT sample scenes
automatically sets up the camera for recording a similar
type of image.
“
”, and then press
[SET].
• This enters the BEST
SHOT mode and displays
all 12 of the BEST SHOT
scenes.
I Example Sample Scene
• Portrait
• Scenery
• Sample scenes are arranged in sequence, starting
from the upper left corner.
2. Use [̆], [̄], [̇], and [̈] to select the sample
scene you want, and then press [SET].
• Use [̆], [̄], [̇], and [̈] to move the selection
boundary around the display. Scrolling past the last
or the first scene scrolls to the next screen of 12-
sample scenes.
• Night Scene
• Night Scene Portrait
• Pressing [MENU] causes the selection boundary to
jump to the first sample scene.
• If you want to check which sample scene is currently
selected or if you want to change to a different
scene, press [SET].
3. Press the shutter button to record the image.
Download from Www.Somanuals.com. All Manuals Search And Download.
98
OTHER RECORDING FUNCTIONS
IMPORTANT!
NOTE
• BEST SHOT scenes were not recorded using this
camera. They are provided as samples only.
• Due to shooting conditions and other factors, an
image recorded using the setup of a BEST SHOT
scene may not produce exactly the results you
expect.
• Operation guidance and the currently selected BEST
SHOT scene appear on the display for about two
seconds if the camera is in the BEST SHOT mode
when you turn it on.
• You can change the camera settings that are made
when you select a BEST SHOT scene. Note,
however, that the BEST SHOT settings revert to their
defaults when you select another BEST SHOT scene
or turn off the camera. If you want to save your
settings for later use, save them as a BEST SHOT
user setup.
• Digital noise reduction processing is performed
automatically when you are recording a night scene,
fireworks, or other image that requires slow shutter
speeds. Because of this, it takes longer to record
images at lower shutter speeds. Make sure that you
do not perform any camera button operations until
the image recording operation is complete.
• When recording the image of a night scene,
fireworks, or some other image using a slow shutter
speed, use of a tripod is recommended to prevent
hand movement.
Download from Www.Somanuals.com. All Manuals Search And Download.
99
OTHER RECORDING FUNCTIONS
3. Use [̇] and [̈] to select the sample scene
Displaying Sample Scenes Individually
You can use the following procedure to display BEST
SHOT sample scenes individually, so you can view the
explanation about each scene’s settings.
you want, and then press [SET].
• Pressing [MENU] jumps to the first sample scene.
4. Press the shutter button to record the image.
1. In a REC mode, align the mode dial with “ ”,
and then press [SET].
2. Move the zoom
controller.
• This displays the
sample scene that was
selected on the 12-
scene screen.
• To return to the 12-
sample scene screen,
move the zoom
controller again.
Download from Www.Somanuals.com. All Manuals Search And Download.
100
C
OTHER RECORDING FUNCTIONS
IMPORTANT!
Creating Your Own BEST SHOT Setup
• BEST SHOT user setups are located in the camera’s
built-in memory following the built-in sample scenes.
• Selecting a user snapshot setup displays the
indicator “U” in the upper right corner of the monitor
screen, followed by a number (that indicates the
setup number).
You can use the procedure below to save the setup of an
snapshot you recorded as a BEST SHOT scene. After that,
you can recall the setup whenever you want to use it.
1. In a REC mode, align the mode dial with “ ”,
and then press [SET].
• Note that formatting built-in memory (page 174)
deletes all BEST SHOT user setups.
2. Use [̆], [̄], [̇], and [̈] to select “Register
User Scene”, and then press [SET].
3. Use [̇] and [̈] to
display the snapshots
whose setup you
want to register as a
BEST SHOT scene.
4. Use [̆] and [̄] to select “Save”, and then
press [SET].
• This registers the setup. Now you can use the
procedure on page 98 to select your user setup for
recording.
Download from Www.Somanuals.com. All Manuals Search And Download.
101
OTHER RECORDING FUNCTIONS
NOTE
To delete a BEST SHOT user setup
• The following are the settings that are included in a
snapshot setup: focus mode, EV shift value, white
balance mode, flash mode, ISO sensitivity, Metering,
Flash Intensity, Flash Assist, Filter, Sharpness,
Saturation, and Contrast.
• Note that snapshots recorded with this camera only
can be used to create a BEST SHOT user setup.
• You can have up to 999 BEST SHOT user setups in
the camera’s built-in memory at one time.
1. In a REC mode, align the mode dial with “ ”,
and then press [SET].
2. Move the zoom controller to switch from the
12-scene screen to the sample scene.
3. Use [̇] and [̈] to display the user setup you
want to delete.
• You can check the current setup of a scene by
displaying the various setting menus.
4. Press [̄] (
) to delete the user setup.
• BEST SHOT snapshot user setups are stored in
camera built-in memory in the folder named
“SCENE”. File names are assigned automatically
using the format “UEZ10nnn.JPE”, where “nnn” is a
value from 000 through 999.
5. Use [̆] and [̄] to select “Delete”.
6. Press [SET] to delete the file.
7. Select another scene, and then press [SET].
• This returns to the recording state.
Download from Www.Somanuals.com. All Manuals Search And Download.
102
C
OTHER RECORDING FUNCTIONS
IMPORTANT!
Reducing the Effects of Hand or Subject
Movement
You can reduce the effects of subject movement, and for
hand movement that tends to occur when shooting a far-
away subject using telephoto, a fast-moving subject, or
under dim lighting conditions.
• Anti Shake is disabled automatically when any
setting other than “Auto” is selected for ISO
sensitivity. If you want Anti Shake to be operational
after turning it on, be sure to change the ISO
sensitivity setting to “Auto” (page 123).
• Recording with Anti Shake can cause an image to
appear somewhat coarser than normal and can
cause slight deterioration of image resolution.
• The Anti Shake feature may not be able to eliminate
the effects of hand or subject movement when
shaking is severe.
1. Perform one of the procedures below to
enable Anti Shake.
Using the BEST SHOT mode
• Anti Shake is disabled during movie recording.
• The Anti Shake feature may not work when using a
very low shutter speed. If this happens, use a tripod
to stabilize the camera.
1. In a REC mode, align the mode dial with “
then press [SET].
”, and
2. Use [̆], [̄], [̇], and [̈] to select the “Anti Shake”
scene, and then press [SET].
Using the Menu Screen
1. In a REC mode, press [MENU].
2. Select the “REC” tab, select “Anti Shake”, and then
press [̈].
3. Use [̆] and [̄] to select “Auto”, and then press
[SET].
•
(Anti Shake indicator) is displayed on the
monitor screen while Anti Shake is turned on.
2. Press the shutter button to record the image.
Download from Www.Somanuals.com. All Manuals Search And Download.
103
OTHER RECORDING FUNCTIONS
IMPORTANT!
Shooting with High Sensitivity
• High Sensitivity is disabled automatically when any
setting other than “Auto” is selected for ISO
sensitivity. If you want High Sensitivity to be
operational after turning it on, be sure to change the
ISO sensitivity setting to “Auto” (page 123).
• Recording with high sensitivity can cause an image
to appear somewhat coarser than normal and can
cause slight deterioration of image resolution.
• A desirable level of image brightness may not be
possible under very dark conditions.
Higher sensitivity makes it possible to record brighter
images, without using flash, even when there is not enough
lighting available to obtain normal exposure.
1. In a REC mode, align the mode dial with “ ”,
and then press [SET].
2. Use [̆], [̄], [̇], and [̈] to select the “High
Sensitivity” scene, and then press [SET].
• When shooting with slow shutter speeds, use a
tripod to protect against the effects of hand
movement.
3. Press the shutter button to record the image.
Download from Www.Somanuals.com. All Manuals Search And Download.
104
C
OTHER RECORDING FUNCTIONS
I Setup Sample Images
Recording Images of Business Cards and
Documents (Business Shot)
Recording a business card, document, whiteboard, or
similarly shaped object from an angle can cause the
subject to appear misshaped in the resulting image.
Business Shot automatically corrects the shape of
rectangular objects to make them appear like the camera
was positioned directly in front of them.
• Business cards and
documents
• White board, etc.
IMPORTANT!
• Before recording, compose the image so outline of
the item you want to record fits entirely within the
monitor screen. The camera will not be able to detect
the shape of the subject correctly unless it is
enclosed entirely within the monitor screen.
• The camera also will be unable to detect the shape
of the subject if it is the same color as the
background. Make sure the subject is against a
background that allows the outline of the subject to
stand out.
Before keystone
correction
After keystone
correction
• Digital zoom is disabled while recording with
Business Shot. However, you can use optical zoom.
Download from Www.Somanuals.com. All Manuals Search And Download.
105
OTHER RECORDING FUNCTIONS
NOTE
To use Business Shot
• When the camera is at an angle to a business card
or document it is recording, the shape of the
business card or document may appear distorted in
the image. Auto keystone correction corrects for this
distortion, which means that subjects appear normal
even if you record at an angle.
1. In a REC mode, align the mode dial with “ ”,
and then press [SET].
2. Use [̆], [̄], [̇] and [̈] to select the
Business Shot image you want, and then
press [SET].
3. Press the shutter
button to record the
image.
• This displays a screen
that shows all of the
objects in the image that
qualify as candidates for
keystone correction. An
error message will
appear (page 236) if the
camera is unable to find
any suitable keystone
correction candidate in
the image. After a short
while, the original image
will be stored in memory,
as-is.
Download from Www.Somanuals.com. All Manuals Search And Download.
106
OTHER RECORDING FUNCTIONS
4. Use [̇] and [̈] to select the candidate you
Recording a Movie
want to correct.
You can record movies with audio. Movie length is limited
only by the amount of memory available for storage. You
can select a resolution setting to suit your needs.
5. Use [̆] and [̄] to
select “Correct”, and
then press [SET].
• File Format: Motion JPEG AVI format
• Selecting “Cancel” in
place of “Correct” stores
the original image as-is,
without correcting it.
• Maximum Movie Length:
The length of a movie is limited only by the amount of
memory available to store it.
• Approximate Movie File Size (1-minute movie):
72.8MB (Quality Setting: HQ)
IMPORTANT!
43.6MB (Quality Setting: Normal)
17.5MB (Quality Setting: LP)
×
• The maximum Business Shot image size is 1600
1200 pixels, even if the camera is configured for a
larger image size. An image size setting smaller than
×
1600 1200 pixels records images at the specified
size.
Download from Www.Somanuals.com. All Manuals Search And Download.
107
OTHER RECORDING FUNCTIONS
Approximate
Data Rate
Specifying Movie Image Quality
Setting
Frame Rate
The image quality setting determines how much the
camera compresses movie images before storing them.
Image quality is expressed as image size in pixels. A
“pixel” is one of the many tiny dots that make up an image.
More pixels (a larger image size) provide finer detail and
higher image quality when a movie is played back.
Before recording a movie, select the image quality setting
that suits your needs.
Higher HQ
10.2 megabits
30 frames/
second
×
Quality (640 480 pixels) per second
Normal 6.1 megabits
(640 480 pixels) per second
Lower LP 2.45 megabits
Quality (320 240 pixels) per second
30 frames/
second
×
15 frames/
second
×
1. In a REC mode, press [MENU].
2. Use [̇] and [̈] to select the “Quality” tab.
3. Use [̆] and [̄] to select “
then press [̈].
Quality” , and
4. Use [̆] and [̄] to select the setting you
want, and then press [SET].
Download from Www.Somanuals.com. All Manuals Search And Download.
108
OTHER RECORDING FUNCTIONS
• Pan Focus (page 84) is selected automatically as the
focus mode in the Movie mode regardless of the
Mode Memory “Focus” setting (page 121) and the
snapshot focus mode setting. You can switch to
another focus mode before you start recording.
Recording a Movie
1. In a REC mode, align the mode dial with
“
”.
• This enters the Movie mode and causes “
appear on the monitor screen.
” to
3. To stop movie recording, press the shutter
button again.
Remaining recording time
2. Point the camera at
the subject and then
press the shutter
button.
• When movie recording is complete, the movie file is
stored in file memory.
• This starts movie
recording.
• This starts movie
recording, which is
REC
indicated by “
the monitor screen.
” on
Recording time
• Movie recording
continues as long as
remaining memory
capacity allows.
Download from Www.Somanuals.com. All Manuals Search And Download.
109
OTHER RECORDING FUNCTIONS
• Very bright light inside of an image can cause a vertical
band to appear in the monitor screen image. This is a
CCD phenomenon known as “vertical smear”, and does
not indicate malfunction of the camera. Note that vertical
smear is not recorded with the image in the case of a
snapshot, but it is recorded in the case of a movie.
• The movie recording capacity of built-in memory is very
small. Use of a memory card (page 175) is recommended
when recording movies.
I Movie Recording Precautions
• The flash does not fire during movie recording
• This camera also records audio. Note the following points
when recording a movie.
— Take care that you do not
block the microphone
with your fingers.
— Good recording results
are not possible when the
camera is too far from the
subject.
— Operating camera
buttons during recording
can cause button noise to
be included in the audio.
— Movie audio is recorded
in monaural.
Microphone
• Certain types of memory cards take longer to record data,
which can cause movie frames to be dropped.
and
REC
flash on the monitor screen during recording to let
you know when a frame has been dropped. Use of an SD
memory card with a maximum transfer speed of at least
10MB per second is recommended.
• Optical zoom is disabled during movie recording. Digital
zoom only is available. Make sure you select the optical
zoom setting you want to use before you press the
shutter button to start movie recording (page 65).
• The effects of camera movement in an image become
more pronounced when you record close ups or recording
with a large zoom factor. Because of this, use of a tripod
is recommended when recording close ups or recording
with a large zoom factor.
— The camera focuses automatically whenever you have
Auto Focus ( ) (page 80) or Macro ( ) (page 83)
selected as the focus mode. Note that the confirmation
tone that sounds during the Auto Focus operation will
be recorded in the audio. If you do not want
confirmation tones in your audio, keep Pan Focus
(
) as the focus mode, or select Manual Focus (
)
and manually focus the image before starting your
recording.
Download from Www.Somanuals.com. All Manuals Search And Download.
110
C
OTHER RECORDING FUNCTIONS
• Images may be out of focus if the subject is outside the
shooting range of the camera.
Recording Audio
• Entering the movie mode automatically changes the focus
mode to Pan Focus (page 84), regardless of the current
mode memory’s (page 121) Focus setting.
Adding Audio to a Snapshot
You can add audio to a snapshot after you record it.
• Image Format: JPEG
JPEG is an image format that provides efficient data
compression.
The file extension of a JPEG file is “.JPG”.
• Audio Format: WAVE/ADPCM recording format
This is the Windows standard format for audio recording.
The file extension of a WAVE/ADPCM file is “.WAV”.
• Recording Time:
Up to about 30 seconds per image
• Audio File Size:
Approximately 165KB (30-second recording of
approximately 5.5KB per second)
NOTE
• You can play back an audio file recorded in the
Audio Snapshot mode on your computer using
Windows Media Player.
Download from Www.Somanuals.com. All Manuals Search And Download.
111
OTHER RECORDING FUNCTIONS
1. In a REC mode, press [MENU].
4. Press the shutter
button to record the
image.
2. Select the “REC” tab, select “Audio Snap”,
and then press [̈].
• After the image is
recorded, the camera
enters audio recording
standby, with the image
you just recorded on the
monitor screen and
3. Use [̆] and [̄] to select “On” and then press
[SET].
• This enters the Audio Snapshot mode.
Remaining recording time
• Selecting “Off” enters the Normal Snapshot mode
(no audio).
displays a
indicator.
• You can cancel audio recording standby by pressing
[MENU].
5. Press the shutter button to start audio
recording.
• The green operation lamp will flash while recording is
in progress.
6. Recording stops after about 30 seconds or
when you press the shutter button.
Download from Www.Somanuals.com. All Manuals Search And Download.
112
C
OTHER RECORDING FUNCTIONS
IMPORTANT!
Recording Your Voice
Voice Recording provides quick and easy recording of your
voice.
• Audio snapshot recording is not supported (audio
cannot be recorded) for the following types of
recording: “X3” self-timer recording (Triple Self-
timer), continuous shutter recording.
• Audio Format: WAVE/ADPCM recording format
This is the Windows standard format for audio recording.
The file extension of a WAVE/ADPCM file is “.WAV”.
• Recording Time:
Approximately 27 minutes with built-in memory
• Audio File Size:
Approximately 165KB (30-second recording of
approximately 5.5KB per second)
NOTE
• You can play back files recorded with Voice
Recording on your computer using Windows Media
Player.
Download from Www.Somanuals.com. All Manuals Search And Download.
113
OTHER RECORDING FUNCTIONS
Recording time
1. In a REC mode, align
the mode dial with
“ ”.
3. Recording stops when you press the shutter
button, when memory becomes full, or when
the camera’s batteries go dead.
• This enters the Voice
Recording mode and
causes “
” to appear
on the monitor screen.
Remaining recording time
2. Press the shutter button to start voice
recording.
• The remaining recording time value counts down on
the monitor screen and the green operation lamp
flashes as recording is performed.
• Pressing [DISP] during voice recording turns off the
monitor screen.
• You can insert index marks while recording by
pressing [SET]. See page 153 for information about
jumping to an index mark during playback.
Download from Www.Somanuals.com. All Manuals Search And Download.
114
OTHER RECORDING FUNCTIONS
I Audio Recording Precautions
Using the Histogram
• Take care that you do not
block the microphone with
your fingers.
Microphone
You can use [DISP] to display a histogram on the monitor
screen (page 35). The histogram lets you check exposure
conditions as you record images. You can also display the
histogram of a recorded image in the PLAY mode.
• Good recording results are not possible when the camera
is too far from the subject.
• Pressing the power button or pressing [
] (PLAY) stops
recording and stores any audio recorded up to that point.
• You can also perform “after-recording” to add audio to a
snapshot after recording it, and also change the audio
recorded for an image. See page 150 for more
information.
Histogram
Download from Www.Somanuals.com. All Manuals Search And Download.
115
OTHER RECORDING FUNCTIONS
• A histogram is a graph that represents the lightness of an
image in terms of the number of pixels. The vertical axis
indicates the number of pixels, while the horizontal axis
indicates lightness. You can use the histogram to
determine whether an image includes the shadowing (left
side), mid tones (center), and highlighting (right) required
to bring out sufficient image detail. If the histogram
appears too lopsided for some reason, you can use EV
shift (exposure compensation) to move it left or right in
order to achieve better balance. Optimum exposure can
be achieved by correcting exposure so the graph is as
close to the center as possible.
NOTE
• You can use key customization (page 119) to
configure the camera to perform exposure
compensation whenever you press [̇] or [̈] while in
a REC mode. If you do this, you can adjust exposure
compensation while viewing the on-screen histogram
(page 87).
• An RGB histogram that shows the distribution of R (red),
G (green), and B (blue) components is also displayed.
This histogram can be used to determine whether there is
too much or too little of each of the color components in
an image.
Download from Www.Somanuals.com. All Manuals Search And Download.
116
OTHER RECORDING FUNCTIONS
• When the histogram is too far
to the left, it means that there
are too many dark pixels.
This type of histogram results
when the overall image is
dark. A histogram that is too
far to the left may result in
“black out” of the dark areas
of an image.
• A centered histogram
indicates that there is good
distribution of light pixels and
dark pixels. This type of
histogram results when the
overall image is at optimal
lightness.
• When the histogram is too far
to the right, it means that
there are too many light
pixels.
This type of histogram results
when the overall image is
light. A histogram that is too
far to the right may result in
“white out” of the light areas of
an image.
Download from Www.Somanuals.com. All Manuals Search And Download.
117
OTHER RECORDING FUNCTIONS
IMPORTANT!
REC Mode Camera Settings
• Note that the above histograms are shown for
illustrative purposes only. You may not be able to
achieve exactly the same shapes for particular
subjects.
• A centered histogram does not necessarily
guarantee optimum exposure. The recorded image
may be over-exposed or under-exposed, even
though its histogram is centered.
• You may not be able to achieve an optimum
histogram configuration due to the limitations of EV
shift.
• Use of the flash as well as certain shooting
conditions can cause the histogram to indicate
exposure that is different from the actual exposure of
the image when it was recorded.
The following are the settings you can configure before
recording an image using a REC mode.
• L/R key setting (key customization)
• Grid on/off
• Image Review on/off
• Power on default settings
• ISO sensitivity
• Metering
• Filter
• Sharpness
• Saturation
• Contrast
• Resetting the camera
• The RGB (color component) histogram is displayed
for snapshots only.
Download from Www.Somanuals.com. All Manuals Search And Download.
118
OTHER RECORDING FUNCTIONS
NOTE
Assigning Functions to the [̇] and [̈]
Keys
• You can also configure the settings listed below. See
the referenced pages for more information.
A “key customization” feature lets you configure the [̇]
and [̈] keys so they change camera settings whenever
they are pressed in a REC mode. After you configure the
[̇] and [̈] keys, you can change the setting assigned to
them without going through the menu screen.
— Continuous (page 97)
— AF Area (page 82)
— Anti Shake (page 103)
— Quick Shutter (page 81)
— Audio Snap (page 112)
— Digital Zoom (page 68)
— Size (page 77)
— Quality (Snapshots) (page 78)
— Quality (Movies) (page 108)
— White Balance (page 89)
— Flash Intensity (page 72)
— Flash Assist (page 72)
1. In a REC mode, press [MENU].
2. Select the “REC” tab, select “L/R Key”, and
then press [̈].
3. Use [̆] and [̄] to select the setting you
want, and then press [SET].
• After you assign a function, you can change its
setting simply by pressing the [̇] and [̈] keys.
— EV Shift (page 87)
— White Balance (page 89)
— ISO (page 123)
— Self-timer (page 74)
— Metering (page 124)
— Off: No function assigned
Download from Www.Somanuals.com. All Manuals Search And Download.
119
OTHER RECORDING FUNCTIONS
Turning the On-screen Grid On and Off
Turning Image Review On and Off
You can display gridlines on the monitor screen to help you
compose images and ensure that the camera is straight
when recording.
Image review displays the images you record on the
monitor screen as soon as you record them. Use the
following procedure to turn image review on and off.
1. In a REC mode, press [MENU].
2. Select the “REC” tab, select “Review”, and
then press [̈].
3. Use [̆] and [̄] to select the setting you
want, and then press [SET].
1. In a REC mode, press [MENU].
To do this:
Select this setting:
On
Display images on the monitor
screen for about one second
immediately after they are recorded
2. Select the “REC” tab, select “Grid”, and then
press [̈].
Do not display images immediately
after they are recorded
Off
3. Use [̆] and [̄] to select the setting you
want, and then press [SET].
To do this:
Select this setting:
Display the grid
Hide the grid
On
Off
Download from Www.Somanuals.com. All Manuals Search And Download.
120
OTHER RECORDING FUNCTIONS
Function
Flash
On
Off
Specifying Power On Default Settings
Auto
Auto
Auto
Auto
The camera’s “mode memory” feature lets you specify the
power on default settings individually for the flash mode,
focus mode, white balance mode, ISO sensitivity, AF Area,
metering, self-timer, flash intensity, digital zoom mode,
manual focus position and zoom position. Turning on mode
memory for a mode tells the camera to remember the
status of that mode when you turn off the camera, and
restore it the next time you turn the camera back on. When
mode memory is turned off, the camera automatically
restores the initial factory default setting for the applicable
mode.
Focus
White Balance
ISO
AF Area
Spot
Metering
Self-timer
Flash Intensity
Digital Zoom
Multi
Off
0
Setting when
camera is
turned off
On
Last Auto Focus
position that was in
effect before you
switched to manual
focus
— The following table shows what happens when you turn
mode memory on or off for each mode.
MF Position
Zoom Position*
Wide
* Only the optical zoom position is remembered.
Download from Www.Somanuals.com. All Manuals Search And Download.
121
OTHER RECORDING FUNCTIONS
IMPORTANT!
1. In a REC mode, press [MENU].
• Note that BEST SHOT mode settings take priority
over mode memory settings. If you turn the camera
off while in the BEST SHOT mode, all settings
except for “Zoom Position” will be configured
according to the BEST SHOT sample scene when
you turn it back on again, regardless of mode
memory on/off settings.
2. Select the “REC” tab, select “Memory”, and
then press [̈].
3. Use [̆] and [̄] to select the item you want to
change, and then press [̈].
4. Use [̆] and [̄] to select the setting you
want, and then press [SET].
To do this:
Select this setting:
On
Turn on mode memory so settings
are restored at power on
Turn off mode memory so settings
are initialized at power on
Off
Download from Www.Somanuals.com. All Manuals Search And Download.
122
OTHER RECORDING FUNCTIONS
IMPORTANT!
Specifying ISO Sensitivity
• Under certain conditions, a high shutter speed in
combination with a high ISO sensitivity setting can
cause digital noise (graininess), which makes an
image appear rough. For clean, good-quality images,
use the lowest ISO sensitivity setting possible.
• Using a high ISO sensitivity setting along with the
flash to shoot a nearby subject may result in
improper illumination of the subject.
You can change the ISO sensitivity setting for better
images in places where lighting is dim or when you are
using faster shutter speeds.
• ISO sensitivity is expressed in terms of values that
originally indicated the sensitivity to light for photographic
film. A larger value indicates higher sensitivity, which is
better for recording when available lighting is dim.
• “Auto” ISO sensitivity always is used for movie
recording, regardless of the current ISO sensitivity
setting.
1. In a REC mode, press [MENU].
2. Select the “Quality” tab, select “ISO”, and
then press [̈].
NOTE
• You can use the key customization feature (page
119) to configure the camera so the ISO sensitivity
setting changes whenever you press [̇] and [̈]
while in a REC mode.
3. Use [̆] and [̄] to select the setting you want
and then press [SET].
To get this:
Select this setting:
Auto
Automatic sensitivity selection
Lower sensitivity
ISO 50
ISO 100
ISO 200
Higher sensitivity
ISO 400
Download from Www.Somanuals.com. All Manuals Search And Download.
123
OTHER RECORDING FUNCTIONS
Multi (Multi pattern)
Selecting the Metering Mode
Multi (Multi pattern) metering divides the
image into sections and measures the
light in each section for a balanced
exposure reading. The camera
automatically determines shooting
conditions according to the measured
lighting pattern, and makes exposure
settings accordingly. This type of
metering provides error-free exposure
settings for a wide range of shooting
conditions.
The metering mode determines what part of the subject is
metered for exposure. You can use the following procedure
to change the camera’s metering mode.
1. In a REC mode, press [MENU].
2. Select the “Quality” tab, select “Metering”,
and then press [̈].
3. Use [̆] and [̄] to select the setting you
want, and then press [SET].
Center Weighted
Center weighted metering measures
light concentrating on the center of the
focus area. Use this metering method
when you want to exert some control
over exposure, without leaving settings
totally up to the camera.
Download from Www.Somanuals.com. All Manuals Search And Download.
124
OTHER RECORDING FUNCTIONS
Spot
IMPORTANT!
Spot metering takes readings at a very
small area. Use this metering method
when you want exposure to be set
according to the brightness of a
particular subject, without it being
affected by surrounding conditions.
• When “Multi” is selected as the metering mode,
certain procedures cause the metering mode setting
to change automatically as described below.
• Changing the exposure compensation setting (page
87) to a value other than 0.0 changes the metering
mode setting to “Center Weighted.” The metering
mode changes back to “Multi” when you return the
exposure compensation setting to 0.0.
NOTE
• You can use the key customization feature (page
119) to configure the [̇] and [̈] buttons so they
select the metering method.
Download from Www.Somanuals.com. All Manuals Search And Download.
125
OTHER RECORDING FUNCTIONS
Using the Filter Function
Specifying Outline Sharpness
The camera’s filter function lets you alter the tint of an
image when you record it.
Use the following procedure to control the sharpness of
image outlines.
1. In a REC mode, press [MENU].
1. In a REC mode, press [MENU].
2. Select the “Quality” tab, select “Filter”, and
2. Select the “Quality” tab, select “Sharpness”,
then press [̈].
and then press [̈].
3. Use [̆] and [̄] to select the setting you
3. Use [̆] and [̄] to select the setting you
want, and then press [SET].
want, and then press [SET].
• Available filter settings are: Off, B/W, Sepia, Red,
Green, Blue, Yellow, Pink, Purple
To get this:
Select this setting:
High sharpness
+2
+1
0
IMPORTANT!
Normal sharpness
Low sharpness
• Using the camera’s filter feature produces the same
effect as attaching a color filter to the lens.
–1
–2
Download from Www.Somanuals.com. All Manuals Search And Download.
126
OTHER RECORDING FUNCTIONS
Specifying Color Saturation
Specifying Contrast
Use the following procedure to control the intensity of the
image you are recording.
Use this procedure to adjust the relative difference
between the light areas and dark areas of the image you
are recording.
1. In a REC mode, press [MENU].
1. In a REC mode, press [MENU].
2. Select the “Quality” tab, select “Saturation”,
2. Select the “Quality” tab, select “Contrast”,
and then press [̈].
and then press [̈].
3. Use [̆] and [̄] to select the setting you
3. Use [̆] and [̄] to select the setting you
want, and then press [SET].
want, and then press [SET].
To get this:
Select this setting:
To get this:
Select this setting:
High color saturation (intensity)
+2
+1
0
High contrast
+2
+1
0
Normal color saturation (intensity)
Low color saturation (intensity)
Normal contrast
Low contrast
–1
–2
–1
–2
Download from Www.Somanuals.com. All Manuals Search And Download.
127
OTHER RECORDING FUNCTIONS
Resetting the Camera
Use the following procedure to reset all of the camera’s
settings to their initial defaults as shown under “Menu
Reference” on page 224.
1. Press [MENU].
2. Select the “Set Up” tab, select “Reset”, and
then press [̈].
3. Use [̆] and [̄] to select “Reset”, and then
press [SET].
• To cancel the procedure without resetting, select
“Cancel” and press [SET].
Download from Www.Somanuals.com. All Manuals Search And Download.
128
PLAYBACK
You can use the camera’s built-in monitor screen to view
images after you record them.
2. Use [̈] (forward) or [̇] (back) to scroll
through files on the monitor screen.
Basic Playback Operation
Use the following procedure to scroll through files stored in
the camera’s memory.
[
]
1. Press [ ] (PLAY) to turn
on the camera.
• This enters the PLAY mode
and causes an image or a
message to appear on the
monitor screen.
PLAY mode file type Folder name/ File name
Image quality
Image size
Date and time
Download from Www.Somanuals.com. All Manuals Search And Download.
129
PLAYBACK
NOTE
Playing an Audio Snapshot
Perform the steps below to display an audio snapshot
• Holding down [̇] or [̈] scrolls images at high
speed.
(indicated by
) and play its audio.
• In order to allow for faster playback image scrolling,
the image that initially appears on the monitor screen
is a preview image, which is of somewhat lower
quality than the actual display image. The actual
display image appears a short while after the preview
image. This does not apply to images copied from
another digital camera.
1. In the PLAY mode, use [̇] and [̈] until the
image you want is displayed.
2. Press [SET].
• This plays back the
audio that accompanies
the displayed image.
• You can perform the
following operations
while audio is playing.
To do this:
Do this:
Fast forward or fast reverse
the audio
Hold down [̇] or [̈].
Pause and unpause audio
playback
Press [SET].
Adjust audio volume
Changing display contents
Cancel playback
Press [̆] or [̄].
Press [DISP] .
Press [MENU].
Download from Www.Somanuals.com. All Manuals Search And Download.
130
PLAYBACK
IMPORTANT!
Zooming the Display Image
• Audio volume can be adjusted only when playback is
being performed or is paused.
Perform the following procedure to zoom the image
currently on the monitor screen up to eight times its normal
size.
1. In the PLAY mode, use [̇] and [̈] to display
the image you want.
Current zoom factor
2. Shift the zoom
controller towards
Original image
(
) to enlarge the
image.
• This zooms the image.
• An indicator appears in
the lower right corner,
that shows what part of
the original image is
currently displayed on
the monitor screen.
Displayed part
• You can toggle display
of the zoom factor on
and off by pressing
[DISP].
Download from Www.Somanuals.com. All Manuals Search And Download.
131
PLAYBACK
3. Use [̆], [̄], [̇], and [̈] to shift the image
Resizing an Image
up, down, left, or right.
You can resize a recorded image to one of three sizes.
4. Press [MENU] to return the image to its
original size.
1. In the PLAY mode, press [MENU].
2. Select the “PLAY”
tab, select “Resize”,
and then press [̈].
IMPORTANT!
• Depending on the original size of the recorded
image, you may not be able to zoom a display image
the full eight times normal size.
• Note that this operation is
possible only when a
snapshot image is on the
monitor screen.
3. Use [̇] and [̈] to scroll through images and
display the one you want to resize.
Download from Www.Somanuals.com. All Manuals Search And Download.
132
PLAYBACK
IMPORTANT!
4. Use [̆] and [̄] to select the setting you
want, and then press [SET].
• Resizing an image creates a new file that contains
the image in the size you select. The file with the
original image also remains in memory.
• Note that you cannot resize the following types of
images.
• When selecting the image size, the image size value
(pixels) will alternate on the display with a
corresponding print size. The print size indicates the
optimum paper size when you print an image that is
the image size you select.
×
— 640 480 pixel and smaller images
— Movie images and the voice recording file icon
— Images created with MOTION PRINT
— Images recorded with another camera
• The resize operation cannot be performed when
there is not enough memory to store the resized
image.
Image Size
Print Size
×
3M
2M
2048 1536 A4 Print
Larger
×
×
1600 1200 3.5˝ 5˝ Print
E-mail (optimum size when
attaching image to e-mail)
×
VGA 640 480
Smaller
• When you display a resized image on the camera’s
monitor screen, the date and time that appear when
the image is displayed indicate when the image was
originally recorded, not when the image was resized.
• When a resized image is displayed on the calendar
screen (page 145), it will appear on the date it was
resized.
* “M” stands for “Mega.”
• To cancel the resize operation, select “Cancel”.
Download from Www.Somanuals.com. All Manuals Search And Download.
133
C
PLAYBACK
Current zoom factor
Original image
3. Select the “PLAY”
tab, select
Cropping an Image
You can use the following procedure to crop a portion of an
enlarged image.
“Trimming”, and then
press [̈].
• An indicator appears in
the lower right corner,
that shows what part of
the original image is
currently displayed on the
monitor screen.
1. In the PLAY mode, use [̇] and [̈] to scroll
through images and display the one you want
to crop.
2. Press [MENU].
Displayed part
• Note that this operation is
possible only when a
snapshot image is on the
monitor screen.
Download from Www.Somanuals.com. All Manuals Search And Download.
134
PLAYBACK
IMPORTANT!
4. Move the zoom controller left and right to
zoom the image.
• Trimming an image causes the original (pre-trimmed)
image and the new (trimmed) version to be stored as
separate files.
• Note that you cannot crop the following types of
images.
— Movie images and the voice recording file icon
— Images created with MOTION PRINT
— Images recorded with another camera
• The cropping operation cannot be performed when
there is not enough memory to store the cropped
image.
• When you display a cropped image on the camera’s
monitor screen, the date and time that appear when
the image is displayed indicate when the image was
originally recorded, not when the image was
cropped.
• The part of the image displayed on the monitor
screen is the cropped part.
5. Use [̆], [̄], [̇], and [̈] to to scroll the part
to be cropped up, down, left, and right.
6. Press [SET] to extract the part of the image
enclosed in the cropping boundary.
• If you want to cancel the procedure at any point,
press [MENU].
• When a cropped image is displayed on the calendar
screen (page 145), it will appear on the date it was
cropped.
Download from Www.Somanuals.com. All Manuals Search And Download.
135
C
PLAYBACK
To do this:
Do this:
Playing and Editing a Movie
Playing a Movie
Use the following procedure to play a movie you recorded
with this camera.
Fast forward or fast reverse
playback
• Each press increases the speed
one more step.
Press [̇] or [̈].
Return fast forward or fast
reverse movie playback to normal Press [SET].
speed
Elapsed recording time
1. In the PLAY mode,
Pause movie playback
Press [SET].
Movie icon
use [̇] and [̈] to
Scroll paused playback one
frame
Press [̇] or [̈].
scroll through movies
on the monitor screen
and display the one
you want.
Stop movie playback
Press [MENU].
Adjust the movie audio volume
level
Press [̆] or [̄].
Toggle monitor screen indicators
on and off
Press [DISP].
Move the zoom
Zoom the movie image
controller towards
Image quality
(
).
Scroll a zoomed movie image on
the monitor screen
Use [̆], [̄], [̇], [̈].
2. Press [SET].
• This starts playback of the movie.
• You can perform the following operations while a
movie is playing.
Download from Www.Somanuals.com. All Manuals Search And Download.
136
PLAYBACK
IMPORTANT!
Editing a Movie
Use the procedure in this section to edit and delete movies.
Editing operations let you cut everything before or after a
specific frame, or to cut everything between two frames.
• You can adjust the volume level of movie audio
during movie playback only.
• You can zoom a movie up to 3.5 times normal size.
• The camera’s playback function may not be able to
play back movies recorded with another camera,
movies transferred from your computer, etc.
IMPORTANT!
• Cut operations cannot be undone. Make sure you
really want to cut the part of the movie you are
specifying before executing the cut operation.
• Movie editing is not possible for movies not recorded
with this camera.
• A movie that is shorter than five seconds cannot be
edited.
• The cut operation can take considerable time. This is
normal and does not indicate malfunction.
• You will not be able to perform the cut operation if
the amount of memory available is less than the size
of the movie file you are cutting. If this happens,
delete any files you no longer need to free up more
memory.
• Splicing of two different movies into a single movie or
cutting one movie into multiple parts are not
supported by camera operations.
Download from Www.Somanuals.com. All Manuals Search And Download.
137
PLAYBACK
3. Use [̆] and [̄] to select the operation you
I To cut everything before or after a specific
frame
want to perform.
To do this:
Select this setting:
Cut
1. While the movie you
are editing is playing,
press [SET].
Cut everything before a
specific frame
Cut everything after a specific
frame
Cut
• This will pause movie
playback.
Exit the cut mode
Cancel
2. Press [̄].
• You can also display the same screen while in the
PLAY mode, by pressing [MENU], selecting the
“PLAY” tab, selecting “Movie Editing”, and then
pressing [̈].
Download from Www.Somanuals.com. All Manuals Search And Download.
138
PLAYBACK
4. Display the frame where you want the cut to
be located.
5. When the frame you
want is displayed,
press [̄].
To do this:
Do this:
Fast forward or fast reverse
playback
Press [̇] or [̈].
Pause or unpause movie
playback
Press [SET].
Scroll paused playback one
frame
Press [̇] or [̈].
6. Use [̆] and [̄] to select “Yes,” and then
Cancel the cut operation
Press [MENU].
press [SET].
• The message “Busy.... Please wait...” will remain on
the display as the cut operation is performed. Cutting
is complete when the message disappears.
• The red portion of the
indicator bar shows
what part will be cut.
• Select “No” to exit the cut mode.
Download from Www.Somanuals.com. All Manuals Search And Download.
139
|