Carbine Stereo Receiver M9900DVDS User Manual

R
Installation  
and Operations  
Manual  
M9900DVDS  
AM / FM / WB and DVD / CD Stereo Receiver  
U.S. Patent No. D486,815  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Disc Notes  
Disc Formats Supported by this Player:  
Label side up  
I
D
E
O
V
Do not touch  
the underside  
of the disc  
Do not bend  
Discs which Cannot be Played with this Player  
• DVD-ROM  
• DVD-R/DVD-RAM  
• CDV  
Wipe the disc from center  
toward the outside edge  
• CD-G  
Handling and Cleaning  
• Dirt, dust, scratches and warping disc  
will cause non operation.  
• Do not place stickers on disc or  
scratch disc.  
• Do not warp discs.  
• A disc should always be kept in its case when not  
in use to prevent damage.  
• Do not place discs in the following places:  
Preparing New Discs with Rough Spots  
A new disc may have rough edges on its inside  
and outside edges. If a disc with rough edges is  
used, the proper setting will not be performed and  
the player will not play the disc. Therefore, remove  
the rough edges in advance by using a ball point  
pen or pencil as shown. To do this, press the side  
of the pen or pencil against the inside and outside  
edges of the disc.  
1. Direct sunlight.  
2. Dirty, dusty and damp areas.  
3. Near car heaters.  
4. Car seats or dashboard.  
Rough spots on  
outside edge  
Disc Cleaning  
Use a dry soft cloth to wipe the surface. If the disc  
is quite dirty, use a soft cloth slightly moist with  
isopropyl (rubbing) alcohol. Never use solvents  
such as benzine, thinner or conventional record  
cleaners as they may mar the surface of the disc.  
Ball point pen  
or pencil  
Note:  
A
disc may become somewhat scratched  
(although not enough to make it unusable)  
depending on handling and conditions in the  
usage environment.  
Rough spots  
on inside edge  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Radio Button Locations and Functions  
20  
19  
POWER  
EJECT  
1
18  
IR  
4 X 50 WATTS  
VOLUME  
PUSH SEL/  
MENU  
17  
16  
15  
14  
MODE  
AS/PS  
2
DIM  
/ II  
LOUD  
MUTE  
TUNE/TRACK/CH  
13  
12  
PUSH  
SCAN/S-MOD/SETUP  
EQ  
DISP  
ENTER  
BAND  
3
REPEAT  
SHUFFLE  
INTRO  
11  
10  
W-BND  
DISC/CAT  
4
5
6
7
8
9
1. Power On/Off: Push to turn the unit on or off.  
2. Volume/Sound Controls: Rotate to increase or decrease the volume level. Push to scan between the  
different sound controls (Volume, Bass, Treble, Balance and Fader).  
3. Multi-Function Knob:  
Radio Mode:  
Manual Tuning: Rotate the TUNE knob to the left or right and hold until “MANUAL” appears in  
the display then release knob. Rotate the TUNE knob again left or right until the desired  
radio station appears in the display.  
Scan Tuning: Push and release the TUNE knob. The tuner will scan up, pausing for 5 seconds at  
each strong station. Push and release the TUNE knob again to cancel the scan function.  
Seek Tuning: Rotate the TUNE knob to the left or right and release. The tuner will scan to the  
next strong station and stop.  
Sirius Satellite Radio Mode: Push to access Manual Tuning, Category Tuning and Direct Tuning in  
Sirius mode. (See Sirius Radio Operation for more information, page 15)  
DVD Mode: Push to enter DVD Setup Mode (See DVD Setup for more information, page 20)  
CD and CD Changer Mode: Rotate the TUNE knob to the left or right to change the CD track on the disc  
that is playing.  
4. Multi-Function Button #1:  
Radio Mode: Push and hold until a beep is heard to memorize a radio station into memory #1. Push  
and release when recalling preset radio station #1.  
Sirius Satellite Radio Mode: Push and hold until a beep is heard to memorize a radio station into  
memory #1. Push and release when recalling preset radio station #1.  
Push the TUNE button first until “CATEGORY” appears in the display then push button 1 to scroll  
down through the Sirius Radio playback categories.  
CD Changer Mode: Push to change to a lower number disc in the CD changer.  
5. Multi-Function Button #2:  
Radio Mode: Push and hold until a beep is heard to memorize a radio station into memory #2. Push  
and release when recalling preset radio station #2.  
Sirius Satellite Radio Mode: Push and hold until a beep is heard to memorize a radio station into memory  
#2. Push and release when recalling preset radio station #2.  
Push the TUNE button first until “CATEGORY” appear in the display then push button 2 to scroll up  
through the Sirius Radio playback categories.  
CD Changer Mode: Push to change to a higher number disc in the CD changer.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Radio Button Locations and Functions  
6. Multi-Function Button #3:  
Radio and Sirius Satellite Radio Modes: Push and hold until a beep is heard to memorize a radio station  
into memory #3. Push and release when recalling preset radio station #3.  
DVD Mode: Push to select chapter repeat on, title repeat on or repeat off.  
CD Mode: Push to repeat a CD track. Push again to cancel.  
CD Changer Mode: Push to repeat a CD track. Push again to cancel.  
Push and hold to repeat the entire disc. Push again to cancel.  
7. Multi-Function Button #4:  
Radio and Sirius Satellite Radio Modes: Push and hold until a beep is heard to memorize a radio station  
into memory #4. Push and release when recalling preset radio station #4.  
CD Mode: Push to play all the tracks on the CD in random order. Push again to cancel.  
CD Changer Mode: Push to play all the tracks on the CD in random order. Push again to cancel.  
Push and hold to play all the CDs in random order. Push again to cancel.  
8. Multi-Function Button #5:  
Radio and Sirius Satellite Radio Modes: Push and hold until a beep is heard to memorize a radio station  
into memory #5. Push and release when recalling preset radio station #5.  
CD Mode: Push to preview each track on the CD for 10 seconds. Push again to cancel.  
CD Changer Mode: Push to preview each track on the CD for 10 seconds. Push again to cancel.  
Push and hold to preview each track on every CD for 10 seconds. Push again to cancel.  
9. Band Button:  
Radio Mode: Push to select F1, F2, F3, AM1, AM2 or W (weather band).  
Sirius Mode: Push to select SR1, SR2, SR3 or SR4.  
10. Weather Band Radio Button: Push to instantly access the weather band radio. Push the MODE button  
to return to previous source.  
11. Reset Button: Push to restore last programmed settings.  
12. Display Button: Push to display the frequency in radio mode, title/chapter in DVD mode or track in CD  
mode. Push and hold to perform clock setting functions (See Clock Setting for more information,  
page 12).  
13. Equalizer Button: Push to choose between preset sound equalization settings.  
14. Mute Button (DVD,CD Play/Pause) Button:  
Radio and Sirius Satellite Radio Mode: Push to mute volume level. Push again to restore volume.  
DVD, CD and CD Changer Mode: Push to pause disc play, push again to resume play.  
15. Loud (Dim Button): Push and release to boost high and low tones at low volume levels. Push and hold  
to dim or restore backlight of display.  
16. AS/PS (DVD and CD Stop Button):  
Radio Mode: Push for automatic memory storing and preset scan.  
DVD and CD Mode: Push to stop the DVD or CD.  
17. Mode Button: Push to change the play source: Radio, Sirius Satellite Radio, DVD/CD, CD Changer or  
Auxiliary Sources.  
18. Eject Button: Push to eject a DVD/CD.  
19. DVD/CD Slot: To play a disc insert a DVD or CD into slot with label facing up.  
20. Display Area: This area displays all function information for the radios, clock and DVD/CD players.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Remote Control Button Locations and Functions  
Inserting the Remote Control Battery:  
1. Open the battery compartment.  
2. Insert the CR2025 battery. Make  
sure that the positive (+) side of  
the battery is oriented correctly.  
3. Close the battery compartment.  
22  
23  
POWER  
EJECT  
24  
1
W.BAND DISPLAY PROGRAM MUTE  
MODE  
SUBTITLE ANGLE  
ZOOM  
2
3
25  
26  
SHUFFLE REPEAT  
A-B  
4
5
27  
28  
29  
30  
AS PS  
RESUME  
AUDIO  
MENU  
BND  
SETUP  
SCAN  
6
7
S-MODE  
P
N
31  
8
9
OK  
32  
33  
34  
TITLE  
ST  
10  
SEL  
EQ  
11  
13  
12  
14  
16  
CAT  
2
5
8
0
3
1
4
35  
36  
15  
17  
Using the Remote Control:  
Point the remote control towards the  
remote infrared sensor (IR).  
VOLUME  
DISC  
6
18  
TUN TRK CH  
7
9
37  
38  
19  
20  
GOTO  
PBC  
SLOW  
Infrared Sensor  
21  
1. Power  
Push to turn the unit on or off.  
2. W.BAND  
Push to instantly access the weather band radio. Push the MODE button to return to  
previous source.  
3. DISPLAY  
4. SHUFFLE  
Push to display the frequency in radio mode, title/chapter in DVD mode or track in CD  
mode. Push and hold to perform clock setting functions (See Clock Setting for more  
information, page 12).  
CD Mode: Push to play all the tracks on the CD in random order. Push again to cancel.  
CD Changer Mode:  
Push to play all the tracks on the CD in random order. Push again to cancel.  
5. REPEAT  
CD Mode: Push to repeat a CD track. Push again to cancel.  
CD Changer Mode: Push to repeat a CD track. Push again to cancel.  
DVD Mode: Push to select Chapter Repeat On, Title Repeat On or Repeat Off.  
6. (AS/PS)  
Radio Mode: Push and hold for automatic memory storing. Push and release to scan  
preset stations.  
DVD Mode: Push to stop the DVD.  
7. BND (MENU) Radio Mode: Push to select F1, F2, F3, AM1, AM2 or W (weather band).  
Sirius Satellite Radio Mode: Push to select SR1, SR2, SR3, and SR4.  
DVD Mode: Push to access the root menu.  
8. RESUME  
CD Mode: When in stop mode, press this button and play will resume from the stop  
point.  
9. P/N  
10. EQ  
DVD Mode: Switches between PAL, NTSC and AUTO modes.  
Push to choose between preset sound equalization settings.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
Remote Control Button Locations and Functions  
11. AUDIO  
DVD Mode: Changes the audio soundtrack on multi-audio soundtrack DVD disc.  
12. ST (TITLE)  
Radio Mode:  
Mono/Stereo: You can sometimes improve reception of distant stations by selecting mono  
operation. Press and release to select mono or stereo mode in FM band only. Stereo  
mode is indicated by a ST in the display. Mono mode is indicated by a MON in the display  
.
Local/Distant: Local setting is for reception of strong stations, and distant setting is  
for reception of weaker stations. This function is in effect during Scan and Seek tuning.  
Press and hold to select local or distance mode in FM band only. Local mode  
is indicated by a LOC in the display. Distance mode is not indicated in the display.  
DVD Mode: Push to display the Title menu that is stored in DVD disc (when available).  
13. 3  
Radio Mode: Push and hold until a beep is heard to memorize a radio station into  
memory #3. Push and release when recalling preset radio station #3.  
Sirius Satellite Radio Mode: Push and hold until a beep is heard to memorize a radio  
station into memory #3. Push and release when recalling preset radio station #3.  
DVD Mode: Push to select chapter repeat on, title repeat on or repeat off.  
CD Mode: Use in conjunction with other numeric buttons to input track number.  
CD Changer Mode: Push and release to repeat the track playing on the CD and “RPT” will  
appear in the display. Push again to cancel. Push and hold until “DRT” appears in the  
display to repeat the disc playing in the changer. Push again to cancel.  
14. 1 (CAT  
)
)
Radio Mode: Push and hold until a beep is heard to memorize a radio station into  
memory #1. Push and release when recalling preset radio station #1.  
Sirius Satellite Radio Mode: Push and hold until a beep is heard to memorize a radio  
station into memory #1. Push and release when recalling preset radio station #1.  
Push the SCAN button (29) first until “CATEGORY” appears in the display then push  
button 1 to scroll down through the Sirius Radio playback categories.  
CD Mode: Use in conjunction with other numeric buttons to input track number.  
15. 2 (CAT  
Radio Mode: Push and hold until a beep is heard to memorize a radio station into  
memory #2. Push and release when recalling preset radio station #2.  
Sirius Satellite Radio Mode: Push and hold until a beep is heard to memorize a radio  
station into memory #2. Push and release when recalling preset radio station #2.  
Push the SCAN button (29) first until “CATEGORY” appear in the display then push  
button 2 to scroll up through the Sirius Radio playback categories.  
CD Mode: Use in conjunction with other numeric buttons to input track number.  
CD Changer Mode: Push and release to scan each track on the CD and “SCN” will  
appear in the display. Push again to cancel. Push and hold until “DSN” appears in the  
display to scan each track on each disc in the CD Changer. Push again to cancel.  
16. 6 (DISC  
17. 4  
)
CD Mode: Use in conjunction with other numbered buttons to input track number.  
CD Changer Mode: Push to change to a higher disc in the CD changer  
.
Radio Mode: Push and hold until a beep is heard to memorize a radio station into  
memory #4. Push and release when recalling preset radio station #4.  
Sirius Satellite Radio Mode: Push and hold until a beep is heard to memorize a radio  
station into memory #4. Push and release when recalling preset radio station #4.  
CD Mode: Use in conjunction with other numeric buttons to input track number.  
CD Changer Mode: Push and release to play all the tracks on the CD in random order  
and “SHF” will appear in the display. Push again to cancel. Push and hold until “DSF”  
appears in the display to play all the discs in random order. Push again to cancel.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Remote Control Button Locations and Functions  
18. 5 (DISC  
)
Radio Mode: Push and hold until a beep is heard to memorize a radio station into  
memory #5. Push and release when recalling preset radio station #5.  
Sirius Satellite Radio Mode: Push and hold until a beep is heard to memorize a radio  
station into memory #5. Push and release when recalling preset radio station #5.  
CD Mode: Use in conjunction with other numeric buttons to input track number.  
CD Changer Mode: Push to change to a lower disc in the CD changer  
.
19. 7, 8, 9, 0  
20. GO TO  
21. PBC  
Use in conjunction with other numeric buttons.  
DVD Mode: Goes to bookmark function during DVD playback.  
Change between PBC On and PBC Off on VCD discs.  
22. PROGRAM CD Mode: Allows the tracks to be played in the order you programmed (See  
Programming CD Tracks into Memory, page 13).  
23. A-B  
24. (EJECT) Push to eject a DVD/CD.  
25. MODE Push to change the play source: Radio, Sirius Satellite Radio, DVD/CD, CD Changer or  
CD and DVD Modes: Allows a passage to be repeated continuously (CD and DVD).  
Auxiliary Sources.  
26.  
(MUTE) Radio and Sirius Satellite Radio Mode: Push to mute volume level. Push again to  
restore volume.  
CD and CD Changer Mode: Push to pause disc play, push again to resume play.  
DVD Mode: Push to pause movie play, push again to resume play.  
27. ANGLE  
DVD Mode: Changes the view angle on multi-angle DVD disc.  
28. SUBTITLE  
DVD Mode: Changes the Subtitle language on multi-subtitle language DVD disc.  
29. SCAN  
(SETUP)  
Radio Mode: Scan Tuning: Push and release the SCAN button. The tuner will scan up,  
pausing for 5 seconds at each strong station. Push and release the SCAN button again  
to cancel the scan function.  
DVD Mode: Push to enter DVD Setup Mode (See DVD Setup for more information, page 20)  
Sirius Satellite Radio Mode: Push to access Manual Tuning, Category Tuning and Direct  
Tuning. (See Sirius Radio Operation for more information, page 15).  
30. ZOOM  
DVD Mode: Enlarges or reduces size of picture.  
31.  
/
Radio Mode: Manual Tuning: Push and hold one of the buttons until “MANUAL” appears in  
the display then release button. Push the buttons again up or down until the desired radio  
station appears in the display.  
DVD Mode: When the menu is displayed these buttons work as navigational buttons.  
When a movie is playing these buttons work as Chapter Skip buttons.  
32.  
/
Radio Mode: Seek Tuning: Push the left or right button and release. The tuner will scan  
to the next strong station and stop.  
DVD Mode: When the menu is displayed these buttons work as navigational buttons.  
When a movie is playing these buttons work as Fast Forward (FF) and Fast Rewind (FR)  
buttons.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
Remote Control Button Locations and Functions  
33. OK  
DVD Mode: Confirm the Track/Chapter selected with the numeric buttons or selected  
with the cursor buttons on screen display.  
34. SEL  
Push to scan between the different sound controls (Volume, Bass, Treble, Balance and  
Fader). Then push VOL +/ to change the setting.  
-
35.  
36.  
-
/ +  
Push to increase or decrease the volume level.  
VOLUME  
/
Radio Mode: Push the left or right button and release. The tuner will scan to the next  
TUN/TRK/CH  
strong station and stop.  
Sirius Satellite Radio Mode: Push the left or right button and release. The tuner will go  
to the next station and stop.  
CD and CD Changer Mode: Push the left or right button and release to change the  
track on the CD that is playing.  
DVD Mode: When a movie is playing these buttons work as Chapter Skip buttons.  
37.  
/
Radio: Push the left or right button until the desired radio station appears in display.  
CD and CD Changer Mode: Push and hold the left or right button to Fast Rewind or  
Fast Forward the track playing.  
DVD Mode: When a movie is playing push  
to scroll through Fast Forward (FF 2 X,  
to scroll through  
FF 4 X, FF 6 X, FF 8 X and PLAY to return to normal). Push  
Fast Reverse (FR 2 X, FR 4 X, FR 6 X, FR 8 X and PLAY to return to normal).  
38. SLOW  
DVD Mode: Push to scroll through Slow Forward (SF 2 X, SF 4 X, SF 8 X) then Slow  
Reverse (SR 2 X, SR 4 X, SR 8 X) then normal (PLAY).  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Basic Operation  
POWER  
Turning the Unit On and Off: Push the Power button.  
Selecting Play Source: Push the Mode button to choose a play source:  
Radio, Sirius Satellite Radio (if equipped), CD/DVD, External CD Changer  
(if equipped) or Auxiliary Sources (if equipped).  
MODE  
AS/PS  
DIM  
/ II  
Dimming the Display: Push and hold the LOUD button to dim the backlight  
of the display. Push and hold again to return to normal illumination.  
LOUD  
MUTE  
AM/FM Radio Operation  
AM/FM Bands: Push BAND button to select a radio band: F1, F2, F3, AM1,  
AM2 or W (weather band).  
BAND  
W-BND  
TUNE/TRACK/CH  
Manual Tuning:  
PUSH  
SCAN/S-MOD/SETUP  
1. Rotate the TUNE knob left or right and hold until “MANUAL” appears  
in the display, then release knob.  
2. Rotate the TUNE knob again left or right until the desired radio  
station appears in the display.  
TUNE/TRACK/CH  
PUSH  
SCAN/S-MOD/SETUP  
Scan Tuning: Push the TUNE knob to have the radio automatically scan  
every 5 seconds for a different radio station. To stop scanning push the  
TUNE knob again.  
TUNE/TRACK/CH  
PUSH  
SCAN/S-MOD/SETUP  
Seek Tuning: Rotate the TUNE knob left or right, then release to seek for a  
different radio station.  
Preset AM/FM Radio Stations  
Programming AM/FM Radio Stations: You can program up to 15 FM radio  
stations and 10 AM radio stations.  
1. Select from F1, F2, F3, AM1 or AM2 by pushing the BAND button  
repeatedly.  
BAND  
W-BND  
2. Tune to the desired radio station (see AM/FM Radio Operation above  
for more details).  
3. Push and hold one of the five STATION RECALL buttons  
until a short "beep" is heard. The corresponding preset  
button number now appears in the lower right hand  
corner of the display.  
REPEAT  
SHUFFLE  
INTRO  
4. To program additional preset stations, repeat this procedure using the  
other STATION RECALL buttons.  
Automatically Programming AM/FM Radio Stations: You can program up to  
15 FM radio stations and 10 AM radio stations automatically.  
1. Select from F1, F2, F3, AM1 or AM2 by pushing the BAND button  
BAND  
W-BND  
AS/PS  
repeatedly.  
2. Push and hold AS/PS button until the display starts scanning for a  
radio station. The radio will automatically program the 5 strongest  
station into preset memory.  
MODE  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
(continued)  
Preset AM/FM Radio Stations  
Recalling AM/FM Radio Stations:  
BAND  
W-BND  
1. Select from F1, F2, F3, AM1 or AM2 by pushing the BAND button  
repeatedly.  
2. Push button 1, 2, 3, 4 or 5 to recall a preprogrammed radio  
station.  
REPEAT  
SHUFFLE  
INTRO  
Automatically Recalling AM/FM Radio Stations:  
BAND  
MODE  
W-BND  
AS/PS  
1. Select from F1, F2, F3, AM1 or AM2 by pushing the BAND button  
repeatedly.  
2. Push the AS/PS button and release to automatically scan every 5 seconds  
the through preprogrammed radio stations. To stop scanning push the  
AS/PS button again.  
Weather Band Radio Operation  
Weather Band: Push the W-BND button to immediately access the weather  
band. The radio will search for the strongest weather band signal in your area.  
BAND  
W-BND  
PUSH  
TUNE/TRACK/CH  
SCAN/S-MOD/SETUP  
S
can Tuning: Push the TUNE knob to scan every 5 seconds through all 7  
weather band stations. To stop scanning push the TUNE knob again.  
TUNE/TRACK/CH  
Manual Tuning:  
PUSH  
SCAN/S-MOD/SETUP  
1. Rotate the TUNE knob left or right and hold until “MANUAL” appears  
in the display, then release knob.  
2. Rotate the TUNE knob again left or right until the desired weather  
band radio station appears in the display.  
Directly Recalling Weather Band Radio Stations:  
1. Push button 1, 2, 3, 4 or 5 to directly recall weather  
band station 1 thru 5.  
REPEAT  
SHUFFLE  
INTRO  
Sound Controls  
VOLUME  
PUSH SEL/  
MENU  
Volume Control: Rotate the VOLUME knob to the right to increase levels or  
left to decrease levels.  
Bass, Treble, Balance and Fader Controls: Push and release the VOLUME knob  
to scan between the different sound controls. Once the desired function is in  
the display area rotate the knob left or right to achieve the desired level.  
VOLUME  
PUSH SEL/  
MENU  
Bass Control: The bass control adjusts the amount of low frequency that  
you hear.  
4
X
50 WATTS  
H
NU  
SEL/  
LOC  
Treble Control: The treble control adjusts the amount of high frequency  
that you hear.  
USH  
VOLUME  
Balance Control: The balance control adjusts the amount of sound output  
to the left and right speakers.  
PUSH SEL/  
MENU  
Fader Control: The fader control adjusts the amount of sound output to  
the front and rear speakers.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
(continued)  
Sound Controls  
Equalizer: Push the EQ button to choose between preset equalizer settings:  
Classic, Rock, DSP Off (digital sound processor off), Flat, Pop and Jazz,  
as indicated in the display area.  
EQ  
DISP  
DIM  
/ II  
MUTE  
Mute (DVD, CD Play/Pause) Button: Push the MUTE button to mute the  
radio volume. If a DVD or CD is playing the MUTE button will pause the  
disc. Push the MUTE button again to restore the volume or resume play-  
ing the disc.  
LOUD  
Loudness: Push the LOUD button to boost high and low tones at low  
volume levels.  
LOUD  
MUTE  
Clock Setting  
Display Button: Push and hold the DISP button until the clock is flashing in  
EQ  
DISP  
PUSH  
the display.  
TUNE/TRACK/CH  
Adjusting the Minutes: Rotate the TUNE knob to the Left to adjust the Minutes.  
SCAN/S-MOD/SETUP  
Adjusting the Hours: Rotate the TUNE knob to the Right to adjust the Hours.  
Note: the AM/PM indicators.  
When correct time displays wait a few seconds to allow the time to program.  
Minutes  
Hours  
CD Operation  
Playing a CD: Insert a CD (label side up) into the CD slot. The CD will  
auto-load and start playing.  
Note: If a CD does not auto-load DO NOT FORCE IT into the slot, as you  
may already have a disc loaded.  
TUNE/TRACK/CH  
PUSH  
SCAN/S-MOD/SETUP  
CD Track Selection: Rotate the TUNE knob left or right to change the track.  
The track number will appear in the display.  
DIM  
/ II  
Pausing a CD: Push the MUTE button to “Pause” the disc, push again to  
resume play.  
LOUD  
MUTE  
EJECT  
Ejecting a CD: Push the EJECT button to to eject a disc.  
Repeating a CD Track: Select the desired track to repeat then push the  
REPEAT button until “S-RPT” appears in the display. That track will play  
repeatedly. To cancel this feature push the REPEAT button until “S-RPT” dis-  
appears from the display.  
REPEAT  
Random CD Track Play Order: Push the SHUFFLE button until “S-SHF” appears  
in the display. The tracks on the disc will play in a random order. To cancel this  
feature push the SHUFFLE button until “S-SHF” disappears from the display.  
SHUFFLE  
Preview CD Tracks: Push the INTRO button until “S-SCN” appears in the  
display. Each track on the disc will play for 10 seconds. To cancel this  
feature push the INTRO button until “S-SCN” disappears from the display.  
INTRO  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
(continued)  
CD Operation  
Elapse Times: Push the AS/PS button to display running time of CD track,  
push the button again to display the time remaining on the CD track, push  
one more time to display time remaining on CD.  
MODE  
AS/PS  
AS PS  
Programming CD Tracks into Memory (Using the Remote Control):  
1. In CD mode, push the AS/PS button on the remote control  
.
PROGRAM  
2. Push the PROGRAM button and P00-0000 will appear in the display.  
CAT  
2
5
3
1
4
7
3. Push the Numeric buttons to select the first track to be programmed  
into memory. For example: push numeric button 4, “P01-004” appears  
in the display indicating that track 4 will be played first.  
DISC  
6
9
8
0
4. Repeat Step 3 to store up to 99 tracks into memory.  
MUTE  
5. Push the  
MUTE button to play tracks in programmed order.  
Canceling Programmed CD Tracks:  
1. Push the AS/PS button  
AS PS  
.
PROGRAM  
MUTE  
2. Push the PROGRAM button.  
3. Push the  
MUTE button to resume normal play.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CD Changer Operation  
Loading CDs: Load CDs into the CD magazine and insert the magazine into  
the external CD changer  
Selecting the External CD Changer: Push the MODE button until “CDC”  
MODE  
AS/PS  
appears in the display.  
CD Selection: Push button 1 or 2 to scroll through the selection of CDs in the  
CD changer. If a CD is not in one of the trays, the unit will continue until the  
next CD is found.  
DISC/CAT  
TUNE/TRACK/CH  
PUSH  
SCAN/S-MOD/SETUP  
CD Track Selection: Rotate the TUNE knob left or right to change the track.  
The track number will appear in the display.  
Repeating a CD Track: Select the desired track to repeat then push and  
release the REPEAT button until “RPT” appears in the display. The track  
on the disc will play repeatedly. To cancel this feature push the REPEAT  
button until “RPT” disappears in the display.  
REPEAT  
Repeating a CD: Select the desired CD to repeat then push and hold the  
REPEAT button until “DPT” appears in the display. The entire disc will  
play repeatedly. To cancel this feature push the REPEAT button until  
“DPT” disappears from the display.  
Random CD Track Play Order: Push and release the SHUFFLE button until  
“SHF” appears in the display. The tracks on the disc will play in a random  
order. To cancel this feature push the SHUFFLE button until “SHF”  
disappears from the display.  
SHUFFLE  
Random CD Play Order: Push and hold the SHUFFLE button until “DSF”  
appears in the display. The discs will play in a random order. To cancel this  
feature push the SHUFFLE button until “DSF” disappears from the display.  
Preview CD Tracks: Push and release the INTRO button until “SCN” appears  
in the display. Each track on the disc will play for 10 seconds. To cancel  
this feature push the INTRO button until “SCN” disappears from the display.  
INTRO  
Preview CDs: Push and hold the INTRO button until “DSN” appears in the  
display. Each track on every disc will play for 10 seconds. To cancel this  
feature push the INTRO button until “DSN” disappears from the display.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Sirius Satellite Radio Setup  
Note: If your Sirius tuner is not activated, call 1-888-539-SIRIUS to activate. The Sirius Tuner ID Number  
(ESN) is required during the activation process. Following the instructions below to access the Sirius  
Tuner ID Number (ESN):  
Accessing you Sirius Tuner ID Number (ESN):  
MODE  
AS/PS  
1. Push the MODE button until “SIRIUS” appears in the display area.  
TUNE/TRACK/CH  
PUSH  
SCAN/S-MOD/SETUP  
2. Push the TUNE button until “DIRECT” appears in the display area. Wait a  
few seconds and “CH 000” will then appear in the display.  
3. Push the BAND button and the first 4 digits of the 12 digit Sirius Tuner ID  
Number (ESN) will be displayed.  
BAND  
W-BND  
4. Push the DISP button and the last 8 digits of your 12 digit Sirius Tuner  
ID Number (ESN) will be displayed.  
EQ  
DISP  
TUNE/TRACK/CH  
PUSH  
SCAN/S-MOD/SETUP  
5. Push the TUNE button to exit.  
Sirius Satellite Radio Operation  
Please note that satellite radio signal may be blocked by trees, buildings, bridges or tunnels.  
Selecting Sirius Satellite Radio: Push the MODE button until “SIRIUS”  
MODE  
AS/PS  
appears in the display. Please be patient as it may take a minute to receive a  
satellite signal.  
TUNE/TRACK/CH  
Manual Tuning:  
PUSH  
SCAN/S-MOD/SETUP  
1. Push the TUNE knob until “NORMAL” appears in the display.  
2. Rotate the TUNE knob to select a station from 01-182.  
TUNE/TRACK/CH  
Category Tuning:  
PUSH  
SCAN/S-MOD/SETUP  
1. Push the TUNE knob until “CATEGORY” appears in the display.  
2. Push button 1 or 2 to find the desired category.  
DISC/CAT  
TUNE/TRACK/CH  
3. Rotate the TUNE knob and select a station within the category.  
PUSH  
SCAN/S-MOD/SETUP  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Sirius Satellite Radio Operation (Continued)  
TUNE/TRACK/CH  
Direct Tuning:  
PUSH  
SCAN/S-MOD/SETUP  
1. Push the TUNE knob until “DIRECT” appears in the display.  
2. Rotate the TUNE knob and select the first digit (0 or 1).  
3. Push the TUNE knob again.  
4. Rotate the TUNE knob and select the second digit (1-8).  
5. Push the TUNE knob again.  
TUNE/TRACK/CH  
PUSH  
SCAN/S-MOD/SETUP  
6. Rotate the TUNE knob and select the third digit (1-9). The tuner will  
start playing the station you have selected when the third digit stops  
flashing.  
Preset Sirius Satellite Radio Stations  
Programming Satellite Radio Stations: You can program up to 20 Sirius  
Satellite radio stations.  
1. Select from SR1, SR2, SR3 or SR4 by pushing the BAND button  
repeatedly.  
BAND  
W-BND  
2. Tune to the desired radio station (see Sirius Satellite Radio Operation  
for more details).  
3. Push and hold one of the five STATION RECALL buttons  
until a short "beep" is heard. The corresponding preset  
button number now appears in the lower right hand  
corner of the display.  
REPEAT  
SHUFFLE  
INTRO  
4. To program additional preset stations, repeat this procedure using the  
other STATION RECALL buttons as desired.  
Recalling Satellite Radio Stations:  
BAND  
W-BND  
1. Select from SR1, SR2, SR3 or SR4 by pushing the BAND button  
repeatedly.  
2. Push button 1, 2, 3, 4 or 5 to recall a preprogrammed radio  
station.  
REPEAT  
SHUFFLE  
INTRO  
Automatically Recalling Satellite Radio Stations:  
BAND  
MODE  
W-BND  
AS/PS  
1. Select from SR1, SR2, SR3 or SR4 by pushing the BAND button  
repeatedly.  
2. Push AS/PS button and release to automatically scan every 5 seconds  
the pre-programmed radio stations. To stop scanning push the AS/PS  
button again.  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Channel Skip Sirius Satellite Radio  
Programming Channel Skip for Satellite Radio Stations: You can program  
the radio to skip channels which you do not want.  
1. Tune to the station to be skipped (see Sirius Satellite Radio Operation  
for more details).  
TUNE/TRACK/CH  
PUSH  
SCAN/S-MOD/SETUP  
2. Push the TUNE knob until “SET SKIP” appears in the display.  
ENTER  
BAND  
3. Push the BAND button and “SKIP” will appear flashing in the bottom of  
the display. When the “SKIP” stops flashing the channel has been pro-  
grammed to skip.  
W-BND  
TUNE/TRACK/CH  
Release Channel Skip for Satellite Radio Stations:  
PUSH  
SCAN/S-MOD/SETUP  
1. Push the TUNE knob until “DIRECT” appears in the display.  
2. Rotate the TUNE knob and select the first digit of the skipped channel  
(0 or 1).  
3. Push the TUNE knob again.  
TUNE/TRACK/CH  
4. Rotate the TUNE knob and select the second digit of the skipped channel  
(1-8).  
PUSH  
SCAN/S-MOD/SETUP  
5. Push the TUNE knob again.  
6. Rotate the TUNE knob and select the third digit of the skipped channel  
(1-9). The tuner will start playing the station you have selected when the  
third digit stops flashing.  
TUNE/TRACK/CH  
PUSH  
SCAN/S-MOD/SETUP  
7. Push the TUNE knob until “SET SKIP” appears in the display. After a few  
seconds the radio channel will appear in the display with “SKIP”  
flashing at the bottom.  
ENTER  
BAND  
8. Push the BAND button and “SKIP” will stop flashing in the bottom of the  
display. When the “SKIP” disappears the channel has been released from  
Channel Skip.  
W-BND  
Auxiliary Input  
Selecting Auxiliary Input: Push the MODE button until “AV IN1” or “AV IN2”  
appears in the display which indicates that the auxiliary unit is playing  
through the M9900DVDS.  
MODE  
AS/PS  
Note: All sound controls (pages 11-12) are active when the Auxiliary  
source is playing.  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DVD Operation  
Playing a DVD: Insert a DVD (label side up) into the DVD slot.  
Note: If a DVD does not auto-load DO NOT FORCE into the slot, as you  
may already have a CD or DVD loaded.  
1. The DVD will start playback automatically and stop at the menu display.  
OK  
2. Use the Navigation  
highlighted bar in the menu.  
buttons on the remote to move the  
/
,
/
OK  
3. Press OK button on the remote to confirm selection.  
Stopping a DVD: Push the AS/PS button to stop the unit playback, when the  
MUTE button is pressed, normal playback will continue.  
AS PS  
Push the AS/PS button twice to stop the playback and go back to initial  
Chapter.  
MUTE  
Pausing a DVD: Push the  
MUTE button to “Pause” the disc, push it again  
to resume play.  
EJECT  
Ejecting a DVD: Push the EJECT button to eject a disc.  
Previous Chapter Next Chapter  
Chapter Skip: Push the  
button to skip forward to the next chapter. Push  
the  
button to skip backwards to the previous chapter.  
TUN TRK CH  
Fast Reverse/Fast Forward: Push the  
or  
buttons to fast reverse or fast  
Fast Reverse  
Fast Forward  
forward during play. Each time the button is pressed the speed changes.  
2X  
4X  
6X  
8X  
Normal Playback  
Slow Motion Forward/Reverse: Push the SLOW button to scroll through Slow  
Forward (SF 2X, SF 4X, SF 8x) then Slow Reverse (SR 2X, SR 4X, SR 8x)  
then normal (PLAY).  
SLOW  
SF 2X  
SF 4X  
SF 8X  
SR 2X  
SR 4X  
SR 8X  
Normal Playback  
Repeat Play: Push the REPEAT button to scroll through Chapter Repeat On,  
Title Repeat On and Repeat Off.  
REPEAT  
Chapter Repeat On  
Title Repeat On  
Repeat Off  
Passage Repeat: Allows a passage to be repeated continuously.  
1. Push the A-B button at the start of the required passage.  
2. Push the A-B button at the end of the passage. The unit will repeat playing  
the passage set from A to B.  
A-B  
Cancelling Passage Repeat. To revert to normal play push the A-B button again.  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DVD Operation (continued)  
GO TO Title/Chapter Select Function: To directly select a Title/Chapter follow  
these directions:  
GOTO  
1. Push the GO TO button and the screen will display the TITLE and  
CHAPTER information.  
CAT  
1
4
7
2
3
6
9
DISC  
5
2. Use the Numeric buttons to input the Title/Chapter number.  
3. Push the OK button to execute the GO TO function.  
8
0
OK  
GOTO  
GO TO Time Select Function: To directly select a time in the DVD follow these  
X2  
directions:  
1. Push the GO TO button TWICE and the screen will display the TITLE and  
TIME information.  
CAT  
1
2
3
DISC  
4
7
5
6
9
2. Use the Numeric buttons to input the Time.  
8
0
OK  
3. Push the OK button to execute the GO TO function.  
DVD Disc Information: Push the DISPLAY button to scroll through playback to  
display the console information of the current disc onscreen.  
DISPLAY  
TITLE/CHAPTER  
TITLE REMAIN  
CHAPTER ELAPSE  
CHAPTER REMAIN  
Off  
PAL/NTSC System Selection: Press the P/N button to switch between PAL,  
NTSC and AUTO modes.  
P
N
Note: This function is only effective when the DVD logo is displayed or when  
disc play is stopped.  
Audio Languages Function: Push the AUDIO button during playback. Each  
time the button is pressed, the audio soundtrack language changes in  
sequential order.  
AUDIO  
Notes:  
• The language number maybe different according to the disc.  
• Some discs only contain one language soundtrack.  
• When no different language soundtracks are recorded, will be displayed  
in the top left corner of the screen.  
Subtitle Languages Function: Push the SUBTITLE button during playback. Each  
time the button is pressed, the subtitle language changes in sequential order.  
Notes:  
SUBTITLE  
• The language number maybe different according to the disc.  
• Some discs only contain one subtitle language.  
• When no different language soundtracks are recorded, will be displayed  
in the top left corner of the screen.  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DVD Operation  
Angle Function: Push the ANGLE button during playback. Each time the button  
is pressed, the angle changes in sequential order.  
Notes:  
ANGLE  
• The angle number maybe different according to the disc.  
• The function only works for discs having scenes recorded at different  
angles.  
• When no different angles are recorded, will be displayed in the top left  
corner of the screen.  
Zoom Function: Allows the picture to be increased in size. Push the ZOOM  
button during playback. Each time the button is pressed, the zoom changes  
in sequential order.  
ZOOM  
Zoom X 1.5  
Zoom X 2  
Zoom X 3  
Zoom Off  
Note: During ZOOM mode, press the  
/
,
/
buttons to move picture left,  
right, up or down.  
DVD Setup  
Initial Setup  
General Setup  
- - GENERAL PAGE - -  
SETUP MENU -- MAIN PAGE  
TV DISPLAY  
PIC MODE  
NORMAL /PS  
NORMAL /LB  
WIDE  
GENERAL SETUP  
AUDIO SETUP  
ANGLE MARK  
OSD LANG  
PREFERENCES  
CAPTIONS  
EXIT SETUP  
SCREEN SAVER  
MAIN PAGE  
SETUP  
SCAN  
1. Press SCAN/SETUP and the Initial  
Setup Menu is displayed.  
TV DISPLAY Setup: This is to select the appropriate  
TV aspect ratio (4:3 or 16:9) according to the  
connected TV set.  
2. Select the preferred item by using  
the  
buttons.  
/
,
/
OK  
NORMAL /PS (For 4:3 TV): Played back in PAN  
and SCAN style (If connected to wide-screen  
TV, the left and right edges are cut off).  
3. Push OK button to enter selected  
menu.  
Menus  
NORMAL /LB (For 4:3 TV) Played back in letter  
box style (If connected to wide-screen TV,  
black bands appear at top and bottom of the  
screen).  
General Setup: This setup page includes all the  
items of TV display and Audio output features.  
(See General Setup Menu for more information)  
Audio Setup: This setup page includes all the  
items for Audio. (See Audio Setup Menu for  
more information)  
WIDE (For 16:9 TV): Select when a wide-screen  
TV set is connected.  
Preferences Setup: This setup page includes all  
the support features. (See Preferences Setup  
Menu for more information)  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DVD Setup  
- - GENERAL PAGE - -  
TV DISPLAY  
- - GENERAL PAGE - -  
TV DISPLAY  
PIC MODE  
PIC MODE  
ANGLE MARK  
OSD LANG  
AUTO  
HI-RES  
ANGLE MARK  
OSD LANG  
NON-FLICKER  
CAPTIONS  
CAPTIONS  
SCREEN SAVER  
MAIN PAGE  
ON  
SCREEN SAVER  
MAIN PAGE  
OFF  
PIC Setup: Select AUTO, the player PIC mode will  
depend on DVD disc. Select HI-RES format for  
best image resolution. Select NON-FLICKER format  
on image or picture with noise or distortion.  
SCREENSAVER Setup: Select the SCREENSAVER ON  
or OFF.  
Audio Setup  
- - AUDIO PAGE - -  
- - GENERAL PAGE - -  
LPCM OUTPUT  
MAIN PAGE  
LPCM 48K  
LPCM 96K  
TV DISPLAY  
PIC MODE  
ANGLE MARK  
OSD LANG  
ON  
OFF  
LPCM Setup: Select the LPCM (Line Pulse Code  
Modulation) OUTPUT between LPCM 48K and  
LPCM 96K. The higher the sampling frequency is,  
the better the output audio quality will be. It is rec-  
ommended to select LPCM 96K compression.  
CAPTIONS  
SCREEN SAVER  
MAIN PAGE  
ANGLE MARK Display Setup: If it is set ON, when a  
multi-angle DVD disc is playing, “ “ (the angle  
mark) will appear on the screen. If it is set to  
“OFF” the mark will not appear.  
Preferences Setup  
- - PREFERENCES - -  
TV TYPE  
AUDIO  
AUTO  
NTSC  
PAL  
- - GENERAL PAGE - -  
TV DISPLAY  
PIC MODE  
SUBTITLE  
DISC MENU  
PARENTAL  
PASSWORD  
DEFAULTS  
MAIN PAGE  
ANGLE MARK  
OSD LANG  
CAPTIONS  
ENGLISH  
FRENCH  
GERMAN  
SPANISH  
SCREEN SAVER  
MAIN PAGE  
TV TYPE Setup: This play can play discs recorded in  
either PAL or NTSC format. Select NTSC format,  
when the unit is connected to a NTSC TV. Select  
PAL format, when the unit is connected to a PAL  
TV. Select AUTO format, the player TV output for-  
mat will be according to the DVD disc format.  
OSD LANG (On-Screen Language Display) Setup:  
Select the preferred On-Screen Display language  
by using the  
buttons.  
,
/
- - GENERAL PAGE - -  
TV DISPLAY  
PIC MODE  
ANGLE MARK  
OSD LANG  
CAPTIONS  
ON  
SCREEN SAVER  
MAIN PAGE  
OFF  
Captions Setup: When playing DVD disc, activate the  
CAPTIONS feature by selecting ON and the cap-  
tions (such as the actor dialogue) appear on the  
screen. Deactivate this feature by selecting OFF  
and the caption will appear.  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DVD Setup  
Preferences Setup  
- - PREFERENCES - -  
TV TYPE  
- - PREFERENCES - -  
AUDIO  
TV TYPE  
AUDIO  
SUBTITLE  
DISC MENU  
PARENTAL  
PASSWORD  
DEFAULTS  
MAIN PAGE  
ENGLISH  
FRENCH  
SPANISH  
CHINESE  
JAPANESE  
GERMAN  
SUBTITLE  
DISC MENU  
PARENTAL  
PASSWORD  
DEFAULTS  
MAIN PAGE  
CHANGE  
PASSWORD Setup: Select CHANGE and press the OK  
button. Type the old password (The initial factory  
code is 3308) then key-in a new 4-character pass-  
word. Then retype it again to confirm new pass-  
word.  
AUDIO Setup: Select the preferred AUDIO language  
by using the cursor buttons.  
- - PREFERENCES - -  
TV TYPE  
- - PREFERENCES - -  
ENGLISH  
FRENCH  
SPANISH  
CHINESE  
JAPANESE  
GERMAN  
OFF  
AUDIO  
SUBTITLE  
DISC MENU  
PARENTAL  
PASSWORD  
DEFAULTS  
MAIN PAGE  
TV TYPE  
AUDIO  
SUBTITLE  
DISC MENU  
PARENTAL  
PASSWORD  
DEFAULTS  
MAIN PAGE  
RESET  
SUBTITLE Setup: Select the preferred SUBTITLE  
language by using the cursor buttons.  
DEFAULTS: Select reset to revert to factory initial  
settings.  
- - PREFERENCES - -  
TV TYPE  
AUDIO  
DEFAULT SETTINGS  
GENERAL SETUP TV DISPLAY  
PIC MODE  
NORMAL/PS  
AUTO  
ON  
SUBTITLE  
DISC MENU  
PARENTAL  
PASSWORD  
DEFAULTS  
MAIN PAGE  
ENGLISH  
FRENCH  
SPANISH  
CHINESE  
JAPANESE  
GERMAN  
ANGLE MARK  
OSD LANGUAGE ENGLISH  
CAPTIONS  
SCREENSAVER  
LPCM OUTPUT  
TV TYPE  
OFF  
OFF  
LPCM 96K  
AUTO  
DISC MENU Setup: Select the preferred DISC MENU  
language by using the cursor buttons.  
AUDIO SETUP  
PREFERENCES  
AUDIO  
ENGLISH  
ENGLISH  
ENGLISH  
6PG-R  
3308  
- - PREFERENCES - -  
SUBTITLE  
DISC MENU  
PARENTAL  
PASSWORD  
DEFAULT  
TV TYPE  
AUDIO  
1 G  
2
SUBTITLE  
DISC MENU  
PARENTAL  
PASSWORD  
DEFAULTS  
MAIN PAGE  
3 PG  
4 PG13  
5
RESET  
6 PG-R  
7 NC-17  
8 ADULT  
PARENTAL Setup: Select a suitable parental guidance  
by the cursor buttons and confirm by pressing the  
OK button.  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Speciality Features  
Display Button: The factory default setting is clock display priority. Push the  
DISPLAY button at any time to display the radio frequency, CD track, AUX  
1 or AUX 2.  
EQ  
DISP  
Note: In the Sirius mode the factory default setting is Sirius channel  
display priority. Push the DISPLAY button at any time to display the  
CN-NAME, SONG TITLE, ARTIST, CATEGORY and Clock. If clock is cho-  
sen the time will be displayed for approximately 5 seconds then revert to  
displaying the Category.  
Restoring Factory Default Setting: To restore the radio to the factory default  
MODE  
AS/PS  
W-BND  
setting:  
1. Press the MODE button to select the radio band  
.
ENTER  
BAND  
2. Push the BAND button and and hold until “EEP INIT” appears in the  
display. All settings will be restored to the factory default.  
Reset Button: The radio panel or LCD display may fail to function normally  
due to the vehicle’s battery condition, and may require resetting the radio  
microprocessor if:  
• The vehicle has been “jump started” from a dead battery condition.  
• The vehicle battery becomes very low and is quick-charged.  
• The vehicle battery is removed and replaced.  
Should this condition occur, simply press and release the RESET button  
on the radio panel using the tip of a ball point pen. This will reset the  
radio microprocessor to the original factory settings. After pressing the  
RESET button you should recheck to see if the radio functions normally.  
All station programming should remain, but you will have to reset the  
clock. Should the LCD display area show any abnormal error code, please  
refer to the trouble shooting guide and solution chart below.  
Error Code Problem  
Description  
Possible Remedy  
ERR 1  
Mechanism Problem Unknown mechanical  
problem with the CD  
1. Eject the disc and try another.  
2. Press the reset button.  
3. Replace the unit.  
mechanism.  
ERR 2  
TOC Reading Error  
Laser can not read the  
CD disc table of  
contents.  
1. Insert a different disc.  
2. Check disc for excessive scratches.  
3. Check disc for dirt and fingerprints.  
Clean disc and reinsert.  
ERR 3  
ERR 4  
Error from High  
Ambient Temp.  
The temperature of the Reduce the temperature inside the vehicle  
mechanism is too high and try to play a CD at a later time.  
to play CDs without  
damaging them.  
DVD Error  
Disc Error  
Error during playback  
of disc.  
1. Insert a different disc.  
2. Check disc for excessive scratches.  
3. Check disc for dirt and fingerprints.  
Clean disc and reinsert.  
4. Press the reset button.  
ERR 5  
Error during eject  
and loading disc.  
1. Push the reset button.  
2. Replace the unit.  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Changing the Default Settings  
The M9900DVDS has a small group of settings that can be changed to suit your personalized requirement.  
VOLUME  
Button Confirmation Beep: The factory default setting is BEEP ON (a  
confirmation beep every time a button or knob is pushed). To turn the beeps  
off, push and hold the VOLUME knob until “BEEP ON” is in the display then  
release. Rotate the VOLUME knob until “BEEP OFF” is in the display. Wait a  
few seconds, the radio will return to last radio mode selected.  
PUSH SEL/  
MENU  
Power Up Volume Level: The factory default setting for initial power-up volume  
level is 12. To change the initial volume level, push and hold the VOLUME  
knob until “BEEP ON” is in the display then release. Push the VOLUME knob  
until “P-VOL” is in the display. Rotate the VOLUME knob until the desired  
initial volume is achieved. Wait a few seconds, the radio will return to last  
radio mode selected.  
VOLUME  
PUSH SEL/  
MENU  
Radio Frequency Display: The factory default setting is USA. Do not change this  
setting.  
Clock Display When the Radio is Off: When the ignition key is on and the radio  
is off, “clock display on” is the default setting. To change the setting to “clock  
display off”, push and hold the VOLUME knob until “BEEP ON” is in the  
display then release. Push the VOLUME knob until “CLK ON” is in the display.  
Rotate the VOLUME knob until “CLK OFF” is in the display. Wait a few  
seconds, the radio will return to last radio mode selected.  
VOLUME  
PUSH SEL/  
MENU  
Display Priority: The factory default setting for display priority is “CLOCK”  
except in Sirius mode. To change the display priority (either radio frequency  
priority or no priority), push and hold the VOLUME knob until “BEEP ON” is in  
the display then release. Push the VOLUME knob until “CLOCK” is in the  
display. Rotate the VOLUME knob until “FREQ” or “NO PRI” is in the display.  
Wait a few seconds, the radio will return to last radio mode selected.  
VOLUME  
PUSH SEL/  
MENU  
VOLUME  
Clock Type, 12 hour or 24 hour: The factory default setting is 12 hour clock with  
AM and PM indication. To change the clock type to 24 hour military time,  
push and hold the VOLUME knob until “BEEP ON” is in the display then  
release. Push the VOLUME knob until “12 HOUR” is in the display. Rotate the  
VOLUME knob until “24 HOUR” is in the display. Wait a few seconds, the  
radio will return to last radio mode selected.  
PUSH SEL/  
MENU  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation  
White Wire with Black Stripe: Connect this wire to  
the Left Front Speaker (-) negative terminal or wire.  
S
tep 1: The radio chassis is designed to be “Sleeve  
Mounted” through a opening in the dashboard panel.  
The required opening size is 182mm (7-3/16") x  
84mm (3-5/16"). Cut or engage an opening in the  
dashboard to accommodate the mounting sleeve.  
Green Wire with Black Stripe: Connect this wire to  
the Left Rear Speaker (-) negative terminal or wire.  
Green Wire: Connect this wire to the Left Rear  
Speaker (+) positive terminal or wire.  
Step 2: Insert the mounting sleeve into the hole  
in the dashboard. Bend the metal tabs on the  
sleeve to secure the mounting sleeve to the dash-  
board.  
Gray Wire: Connect this wire to the Right Front  
Speaker (+) positive terminal or wire.  
Gray Wire with Black Stripe: Connect this wire to the  
Right Front Speaker (-) negative terminal or wire.  
Step 3: Bring all wiring for the connection of the  
unit (including the antenna) through the center of  
the mounting sleeve. Connect the wiring as follows:  
Purple Wire with Black Stripe: Connect this wire to  
the Right Rear Speaker (-) negative terminal or wire.  
Yellow Wire (w/Fuse): Connect this wire to a  
constant +12 volt power source (a power source  
that is not controlled by the ignition key).  
Purple Wire: Connect this wire to the Right Rear  
Speaker (+) positive terminal or wire.  
Note: This unit is designed to connect to (4) four  
speakers. If the installation only requires (2) two  
speakers, use the White and Gray wire sets to  
connect the speakers.  
Red Wire: Connect this wire to a switched +12 volt  
power source (a power source turned on and off  
by the ignition key).  
Blue Wire: Connect this wire to the (+) power  
antenna activation circuit. If no power antenna  
exists, tape-off the end of this wire to prevent  
shorting out the unit.  
WARNING! Any wires left unconnected must  
be taped-off or capped off to prevent shorting.  
DO NOT connect speaker ground wires together.  
DO NOT connect speaker ground wires to the  
chassis of the vehicle.  
Black Wire: Connect this wire to the frame of the  
vehicle (ground). This wire is the chassis grounding  
wire for the unit.  
DO NOT connect front and rear speaker wires  
together.  
White Wire: Connect this wire to the Left Front  
Speaker (+) positive terminal or wire.  
FAILURE TO FOLLOW ANY OF THESE WARNINGS  
WILL RESULT IN DAMAGE TO THIS UNIT AND  
VOIDS THE WARRANTY.  
Sheet  
Metal  
Screw  
Nut  
Washer  
POWER  
VOLUME  
PUSH SEL/  
MENU  
Metal Strap  
Dashboard  
TUNE/TRACK  
LO  
C
SCAN/SHIFT  
ME  
EJECT  
M
OR  
Y
PRO2  
G
RA  
M
ELAPSE  
MO  
D
D
3
REPE  
AS  
/
AT  
IM  
PS  
4
LOU  
S
H
/
II  
D
U
FF  
LE  
MU  
DI  
T
5
SC  
EQ  
A
N
S
P
BA  
N
D
W-  
B
Mounting Sleeve  
AN  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connection  
Right  
Front Speaker  
Right  
Rear Speaker  
-
+
+
-
Purple Wire: Rear Right Speaker (+)  
Purple/Black Wire: Rear Right Speaker (-)  
Gray/Black Wire: Front Right Speaker (-)  
Gray Wire: Front Right Speaker (+)  
Green Wire: Rear Left Speaker (+)  
Green/Black Wire: Rear Left Speaker (-)  
White/Black Wire: Front Left Speaker (-)  
White Wire: Front Left Speaker (+)  
-
+
+
-
Black Wire: Ground  
Blue Wire: Power Antenna  
Red Wire: Ignition Switched 12 VDC  
Left  
Front Speaker  
Left  
Rear Speaker  
1 AMP  
Yellow Wire: 12 VDC Constant  
Auxiliary Input 1 (Yellow Cable)  
Audio/Video Output  
Red (Audio In / Right)  
White (Audio In / Left)  
Yellow (Video In)  
VCR  
or  
TV  
or  
DVD  
M9900DVDS  
or  
Auxiliary Input 2 (Black Cable)  
Red (Audio In / Right)  
Video  
Game  
White (Audio In / Left)  
Yellow (Video In)  
Audio Amplifier  
Audio/Video Output (Gray Cable)  
Red (Audio Out / Right)  
See Amplifier Instructions  
for Proper Connections  
White (Audio Out / Left)  
Monitor  
Yellow (Video Out)  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Sirius Tuner Connection (Optional)  
M9900DVDS  
M9SIR  
Sirius Satellite Antenna  
Male/Male Mini Din  
(Supplied with Sirius Tuner)  
CD Changer Connection (Optional)  
Male/Male  
(Supplied with  
External  
CD Changer)  
External CD Changer  
M9900DVDS  
Remote IR Sensor Connection (Optional)  
Remote IR Sensor  
(Mounted In-Dash)  
M9900DVDS  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Antenna Connection  
M9900DVDS  
Antenna  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Trouble Shooting  
If it appears that your DVD unit is faulty, first consult  
the checklist below. It may be that something simple  
has been overlooked. Under no circumstance should  
you try to repair the player yourself, as this will  
invalidate the warranty. Only qualified service person-  
nel should remove the cover or service this player.  
The Player Does Not Respond to the Remote  
Control:  
• Aim the remote control directly at the infrared  
sensor on the front of the player.  
• Avoid all obstacles which may interfere with the  
signal path.  
No Power:  
• Inspect or replace the remote control battery.  
• If the power supply is connected to the car  
accessory circuits, but the engine is not run-  
ning, switch the ignition key to “ACC”.  
Distorted or B/W Picture:  
• The disc format is not set according to the TV  
• Check if the fuse is blown. If so, replace it with  
a new fuse of the same value.  
set used (PAL/NTSC).  
Buttons Do Not Work:  
• Press the RESET button on the front panel of  
• Check if the Power On/Off button is set to on.  
the radio.  
No Picture:  
• Check if the monitor or TV is switched on.  
The Radio Does Not Work:  
• Check if DVD mode is selected.  
• Check the video connection.  
• Check if the antenna cable is properly connected.  
The Radio Station Automatic Selection Does Not  
Work:  
Distorted Picture:  
• The signals maybe too weak, select a station  
manually.  
• Check the disc for debris and clean with soft  
cloth, wiping from the center to the edge.  
• Sometimes a small amount of picture distortion  
may appear. This is not a malfunction.  
Completely Distorted Picture:  
• The disc format is not set according to the TV  
set used (PAL/NTSC).  
No Color in Picture:  
• The disc format is not set according to the TV  
set used (PAL/NTSC).  
Disc Does Not Play:  
• Ensure that the disc was inserted label up.  
• Clean the disc.  
• Check if the disc is defective by trying another  
disc.  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Order-By-Mail Replacement Parts  
DESCRIPTION  
MODEL #  
PRICE  
POWER  
EJECT  
MODE  
W.BAND DISPLAY PROGRAM MUTE  
SHUFFLE REPEAT  
A-B  
SUBTITLE ANGLE  
ZOOM  
AS PS  
RESUME  
AUDIO  
MENU  
BND  
SETUP  
SCAN  
S-MODE  
P
N
OK  
M9900DVDS Remote Control  
RC9900DVD  
$39.95 ea.  
TITLE  
ST  
EQ  
SEL  
CAT  
1
4
2
5
8
0
3
VOLUME  
DISC  
6
TUN TRK CH  
7
9
GOTO  
PBC  
SLOW  
Specifications  
General:  
Power Supply Requirements:  
Chassis Dimensions:  
Tone Controls  
DC 12 Volts, Negative Ground  
180mm (W) x 160mm (D) x 80mm (H)  
Bass (at 100 Hz)  
10 dB  
Treble (at 10 kHz)  
Maximum Output Power  
Current Drain  
10 dB  
4 x 40 Watts  
15 Ampere (max.)  
CD Player:  
Signal to Noise Ratio:  
Channel Separation:  
Frequency Response:  
More than 55 dB  
More than 45 dB  
20Hz - 20kHz  
Radio:  
FM  
Frequency Coverage:  
IF  
87.5 to 107.9 MHz  
10.7MHz  
Sensitivity (S/N = 30dB)  
Stereo Separation  
12 dBu  
> 25 dB  
AM  
Frequency Coverage:  
IF  
530 to 1720 kHz  
450 kHz  
Sensitivity (S/N = 20dB)  
36 dBu  
WB  
Frequency Coverage:  
IF  
162.40 to 162.55 MHz  
10.7MHz  
Sensitivity (S/N = 30dB)  
15 dBu  
Note: Due to improvement in technology, specifications and design are subject to change without notice.  
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Replacement Parts Order Form  
Send Orders To: Magnadyne Corporation  
We Accept Checks, Money Orders, Visa and Master Card  
ATTN: Consumer Parts Sales  
Make Checks Payable to: Magnadyne Corporation  
P.O. Box 5365  
Carson, CA 90749-5365  
SHIP TO: (No P.O. Boxes)  
LAST NAME  
FIRST NAME  
INITIAL  
STREET ADDRESS (IF PAYING WITH A CREDIT CARD, YOUR BILLING ADDRESS IS REQUIRED)  
CITY  
STATE  
ZIP CODE  
DAYTIME PHONE NUMBER  
CREDIT CARD INFORMATION:  
CARD TYPE:  
VISA  
MASTER CARD  
CARD NUMBER  
EXP. MONTH  
YEAR  
NAME - EXACTLY AS IT APPEARS ON YOUR CREDIT CARD  
Part #  
Description  
Qty.  
Price Each  
$39.95  
TOTAL  
Remote Control  
RC9900DVD  
Shipping and Handling  
Subtotal = ________ . ______  
Subtotal + Tax  
Up to $20.00  
20.01 to 30.00  
30.01 to 45.00  
45.01 to 70.00  
Over 70.01  
Add  
$5.00  
5.95  
6.50  
6.95  
7.95  
California Residents Add Sales Tax = ________ . ______  
Shipping and Handling (See Chart) = ________ . ______  
TOTAL = ________ . ______  
No C.O.D.’s  
On regular orders please allow 4-5 weeks for delivery. Please give a shipping address where this order  
may be delivered between the hours of 9 a.m. and 5 p.m. weekdays. If UPS is unable to deliver, your order will be  
returned and additional shipping charges will be required.  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Warranty  
ONE (1) YEAR LIMITED WARRANTY  
Magnadyne Corporation or its authorized agents will within 1 year from the date of sale to you,  
repair, replace or refund the retail sales price of said product or any part thereof, at the option  
of the Magnadyne Corporation or its authorized agents, if said product or part is found defec-  
tive in materials or workmanship, when properly connected and operating on the correct power  
requirements designated for the specific product. This warranty and Magnadyne Corporation or  
its authorized agents obligations hereunder do not apply where the product was; damaged  
while in the possession of the consumer, subjected to unreasonable or unintended use, not rea-  
sonably maintained, utilized in commercial or industrial operations, or serviced by anyone other  
than Magnadyne Corporation or its authorized agents, or where the warning seal on the prod-  
uct is broken or the power and/or plugs are detached from the unit. Magnadyne Corporation or  
any of its authorized agents will not assume any labor costs for the removal and re-installation  
of any product found to be defective, or the cost of transportation to Magnadyne Corporation  
or its authorized agents. Such cost are the sole responsibility of the purchaser.  
This warranty does not cover the cabinet appearance items or accessories used in connection  
with this product, or any damage to recording or recording tape, or any damage to the prod-  
ucts resulting from improper installation, alteration, accident, misuse, abuse or acts of nature.  
MAGNADYNE CORPORATION OR ITS AUTHORIZED AGENTS SHALL NOT BE LIABLE TO ANY-  
ONE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES OR CLAIMS EXCEPT THOSE ACCORD-  
ED BY LAW. NO EXPRESSED WARRANTY OR IMPLIED WARRANTY IS GIVEN EXCEPT THOSE  
SET FORTH HEREIN. NO IMPLIED WARRANTY SHALL EXTEND BEYOND 1 YEAR FROM THE  
DATE OF SALE.  
This warranty extends only to the original purchaser of the product and is not transferable.  
Some states do not allow limitations on how long an implied warranty lasts and some states do  
not allow the exclusion or limitation of incidental or consequential damages, so the above lim-  
itations or exclusion may not apply to you. This warranty gives you specific legal rights and you  
may have other rights that vary from state to state.  
Defective merchandise should be returned to the original point of purchase or secondly, to  
Magnadyne Corporation, 1111 W. Victoria Street, Compton CA 90220. Return Authorization  
must be obtained before sending, or merchandise may be refused.  
M9900DVDS-UM  
Rev. C 4-26-06  
© Copyright 2006  
Magnadyne Corporation  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Belkin Network Card F5U103 User Manual
Blackberry Network Card SWD 500612 User Manual
Black Decker Food Processor Fp1400 User Manual
Bosch Power Tools Laser Level GPL3 User Manual
Brother Fax Machine FAX 2910 User Manual
Canon All in One Printer 3555B001AA User Manual
Casio PDAs Smartphones Pocket PC Terminal User Manual
Cerwin Vega Portable Speaker CVA 28 User Manual
Char Broil Gas Grill 463270613 User Manual
Chicago Electric Cordless Saw 94488 User Manual