08/7,0(',$ꢀ352-(&725
8VHU·Vꢀ0DQXDO
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Features and Design. . . . . . . . . . . . . . . . 2
Computer Input . . . . . . . . . . . . . . . . . . 34
Computer System Selection
34
35
36
38
39
Table of Contents . . . . . . . . . . . . . . . . . . 3
ToThe Owner . . . . . . . . . . . . . . . . . . . . . 4
Safety Instructions . . . . . . . . . . . . . . . . . 5
Auto PC Adjustment
Manual PC Adjustment
Image Level Selection
Screen Size Adjustment
Air Circulation
6
7
8
8
Installing the Projector in Proper Directions
Moving the Projector
Video Input . . . . . . . . . . . . . . . . . . . . . . 41
Video System Selection
Image Level Selection
Screen Size Adjustment
41
42
43
Cautions in Handling the Projector
Compliance . . . . . . . . . . . . . . . . . . . . . . . 9
Part Names and Functions. . . . . . . . . . 10
Picture Image . . . . . . . . . . . . . . . . . . . . 45
Front
10
10
10
11
12
13
15
15
15
16
Image Adjustment
45
Back
Setting. . . . . . . . . . . . . . . . . . . . . . . . . . 48
Bottom
Setting
48
RearTerminal
Maintenance and Care . . . . . . . . . . . . . 56
Side Control and Indicators
Remote Control Unit
Remote Control Battery Installation
Remote Control Receivers and Operating Range
Wired Remote ControlTransmitter
Remote Control Code
Filter Instructions
56
57
58
58
59
60
62
62
63
Replacing the Filter Cartridge
Resetting the Filter Counter
Resetting the Scroll Counter
Lamp Replacement
Resetting the Lamp Counter
Cleaning the Projection Lens
Cleaning the Projector Cabinet
Warning Indicators
Installation . . . . . . . . . . . . . . . . . . . . . . 17
Positioning the Projector
17
17
18
Adjustable Feet
Lens Installation
Appendix . . . . . . . . . . . . . . . . . . . . . . . . 64
Connecting to a Computer (Digital and Analog RGB) 20
Troubleshooting
64
66
69
71
73
74
Connecting to Video Equipment (Video, S-Video)
Connecting the AC Power Cord
21
22
MenuTree
Indicators and Projector Condition
Compatible Computer Specifications
Technical Specifications
Optional Parts
Basic Operation . . . . . . . . . . . . . . . . . . 23
Turning On the Projector
Turning Off the Projector
How to Operate the On-Screen Menu
Menu Bar
23
24
25
26
27
28
30
30
Lens Replacement
74
PJ Link Notice
74
Operating with Projector Control
Operating with Remote Control Unit
Pointer Function
Configurations ofTerminals
Dimensions
75
77
78
Serial Control Interface
Wireless Mouse Operation
Input Selection . . . . . . . . . . . . . . . . . . . 31
Input
31
32
33
Computer Input Source Selection
Video Input Source Selection
Trademarks
Each name of corporations or products in this book is either a registered trademark or a trademark of its respective
corporation.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
ToThe Owner
Safety Precaution
Before installing and operating the projector, read this manual
thoroughly.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS APPLIANCE TO
RAIN OR MOISTURE.
The projector provides many convenient features and
functions. Operating the projector properly enables you to
manage those features and maintains it in good condition for
many years to come.
Improper operation may result in not only shortening the
product life, but also malfunctions, fire hazard, or other
accidents.
– This projector produces intense light from the projection
lens. Do not stare directly into the lens, otherwise eye
damage could result. Be especially careful that children do
not stare directly into the beam.
– Install the projector in a proper position. Otherwise it may
result in a fire hazard.
If your projector seems to operate improperly, read this
manual again, check operations and cable connections and try
the solutions in the “Troubleshooting” section in the back of
this booklet. If the problem still persists, contact the dealer
where you purchased the projector or the service center.
– Allowing the proper amount of space on the top, sides,
and rear of the projector cabinet is critical for proper air
circulation and cooling of the unit. The diagrams shown
here indicates the minimum space required. If the projector
is to be built into a compartment or similarly enclosed,
these minimum distances must be maintained.
– Do not cover the ventilation slots on the projector. Heat
build-up can reduce the service life of your projector, and
can also be dangerous.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
SIDE andTOP
REAR
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR
BACK). NO USER-SERVICEABLE PARTS
INSIDE EXCEPT LAMP REPLACEMENT.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
1.5' (50 cm)
3' (1 m)
1.5' (50 cm)
1.5' (50 cm)
THIS SYMBOL INDICATES THAT DANGEROUS
VOLTAGE CONSTITUTING A RISK OF ELECTRIC
SHOCK IS PRESENT WITHINTHIS UNIT.
– If the projector is unused for an extended time, unplug the
projector from the power outlet.
THIS SYMBOL INDICATES THAT THERE ARE
IMPORTANT OPERATING AND MAINTENANCE
INSTRUCTIONS IN THE USER’S MANUAL WITH
THIS UNIT.
CAUTION ON HANGING FROMTHE CEILING
When hanging the projector from the
ceiling, clean the air intake vents and top
of the projector periodically with a vacuum
cleaner. If you leave the projector unclean
for a long time, the cooling fans can be
clogged with dust, and it may cause a
breakdown or a disaster.
CAUTION
Not for use in a computer room as defined in the Standard
for the Protection of Electronic Computer/Data Processing
Equipment, ANSI/NFPA 75.
DO NOT SET THE PROJECTOR IN GREASY, WET,
OR SMOKY CONDITIONS SUCH AS IN A KITCHEN
TO PREVENT A BREAKDOWN OR A DISASTER. IF
THE PROJECTOR COMES IN CONTACT WITH OIL OR
CHEMICALS, IT MAY BECOME DETERIORATED.
NOTE FOR CUSTOMERS INTHE US
Hg LAMP(S) INSIDE THIS PRODUCT CONTAIN MERCURY
AND MUST BE RECYCLED OR DISPOSED OF ACCORDING
TO LOCAL, STATE OR FEDERAL LAWS.
READ AND KEEPTHIS USER'S MANUAL FOR LATER USE.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Instructions
This projector should be operated only from the type of power
All the safety and operating instructions should be read before
the product is operated.
source indicated on the marking label. If you are not sure of
the type of power supplied, consult your authorized dealer or
local power company.
Read all of the instructions given here and retain them for
later use. Unplug this projector from AC power supply before
cleaning. Do not use liquid or aerosol cleaners. Use a damp
cloth for cleaning.
Do not overload wall outlets and extension cords as this can
result in fire or electric shock. Do not allow anything to rest on
the power cord. Do not locate this projector where the cord
may be damaged by persons walking on it.
Follow all warnings and instructions marked on the projector.
Do not attempt to service this projector yourself as opening
or removing covers may expose you to dangerous voltage
or other hazards. Refer all servicing to qualified service
personnel.
For added protection to the projector during a lightning storm,
or when it is left unattended and unused for long periods of
time, unplug it from the wall outlet. This will prevent damage
due to lightning and power line surges.
Unplug this projector from wall outlet and refer servicing to
qualified service personnel under the following conditions:
a. When the power cord or plug is damaged or frayed.
b. If liquid has been spilled into the projector.
Do not expose this unit to rain or use near water... for
example, in a wet basement, near a swimming pool, etc...
c. If the projector has been exposed to rain or water.
d. If the projector does not operate normally by following
the operating instructions. Adjust only those controls that
are covered by the operating instructions as improper
adjustment of other controls may result in damage and will
often require extensive work by a qualified technician to
restore the projector to normal operation.
e. If the projector has been dropped or the cabinet has been
damaged.
f. When the projector exhibits a distinct change in
performance-this indicates a need for service.
Do not use attachments not recommended by the
manufacturer as they may cause hazards.
Do not place this projector on an unstable cart, stand, or
table. The projector may fall, causing serious injury to a child
or adult, and serious damage to the projector. Use only with
a cart or stand recommended by the manufacturer, or sold
with the projector. Wall or shelf mounting should follow the
manufacturer's instructions, and should use a mounting kit
approved by the manufacturers.
An appliance and cart combination
should be moved with care. Quick stops,
excessive force, and uneven surfaces
may cause the appliance and cart
combination to overturn.
When replacement parts are required, be sure the service
technician has used replacement parts specified by the
manufacturer that have the same characteristics as the original
part. Unauthorized substitutions may result in fire, electric
shock, or injury to persons.
Upon completion of any service or repairs to this projector,
ask the service technician to perform routine safety checks to
determine that the projector is in safe operating condition.
Slots and openings in the back and bottom of the cabinet are
provided for ventilation, to ensure reliable operation of the
equipment and to protect it from overheating.
The openings should never be covered with cloth or other
materials, and the bottom opening should not be blocked
by placing the projector on a bed, sofa, rug, or other similar
surface. This projector should never be placed near or over a
radiator or heat register.
This projector should not be placed in a built-in installation
such as a book case unless proper ventilation is provided.
Never push objects of any kind into this projector through
cabinet slots as they may touch dangerous voltage points
or short out parts that could result in a fire or electric shock.
Never spill liquid of any kind on the projector.
Do not install the projector near the ventilation duct of air-
conditioning equipment.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Instructions
Air Circulation
Openings in the cabinet are provided for ventilation.
To ensure reliable operation of the product and to
protect it from overheating, these openings must not
be blocked or covered.
IMPORTANT!
Filter Maintenance!!
The projector uses a lamp which generates
significant heat. The cooling fans and air vents are
provided to dissipate the heat by drawing air into the
housing and the filter is located in the intake vents to
prevent dust from getting inside of the projector.
CAUTION
Hot air is exhausted from the exhaust vent. When
using or installing the projector, the following
precautions should be taken.
–Do not put any flammable object or spray can near
the projector, hot air is exhausted from the air
vents.
In order to care for the projector appropriately,
regular cleaning is required. Remove any dirt or dust
that has accumulated on the projector.
–Keep the exhaust vent at least 3’ (1 m) away from
any objects.
If the projector reaches a time set in the timer
setting, a Filter replacement icon (Fig. 1) appears on
the screen and WARNING FILTER indicator on the
top panel lights up (see below), indicating that the
filter replacement is necessary.
–Do not touch peripheral parts of the exhaust vent,
especially screws and metallic parts. These areas
will become hot while the projector is being used.
–Do not put anything on the cabinet. Objects put on
the cabinet will not only get damaged but also may
cause fire hazard by heat.
If the projector detects that the filter is clogged and
no scroll is left in the filter cartridge, a Filter cartridge
replacement icon (Fig. 2) appears on the screen and
WARNING FILTER indicator on the top panel lights
up (see below). Stop using the projector immediately
and replace the filter cartridge.
Cooling fans are provided to cool down the projector.
The fans’ running speed is changed according to the
temperature inside the projector.
Blocking the air vents and leaving the projector
uncleaned for a long time may not only damage the
projector and may require costly repairs but may also
cause accidents or fire.
Exhaust Vent
(Hot air exhaust)
Air flow
For maintenance of the filter, refer to “Filter counter”
on page 55 and “Maintenance and Care” on pages
56–58.
Damages to the projector caused by using an
uncleaned filter or improper maintenance will
void the warranty on the projector.
Air Intake Vent
Top Panel
Fig.1 Filter replacement icon
Fig.2 Filter cartridge replacement
WARNING FILTER
indicator
icon
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Instructions
Installing the Projector in Proper Directions
Use the projector properly in specified positions. Improper positioning may reduce the lamp life and result in
severe accident or fire hazard.
This projector can project the picture in upward, downward, or inclined position in perpendicular direction to the
horizontal plane. When installing the projector in downwardly inclined position, install the projector bottom side
up.
ꢀNote:
• When the image is top/bottom and left/right reversed, set the ceiling function to “On.” (pp. 40, 44)
Positioning Precautions
Avoid positioning the projector as described below when installing.
10˚
10˚
Do not tilt the projector more than
10 degrees from side to side.
In upward projection, do
not tilt the projector over 10
degrees right and left.
10˚
10˚
Do not put the projector on either
side to project an image.
In downward projection, do
not tilt the projector over 10
degrees right and left.
10˚
10˚
CAUTION ON CEILING MOUNTING
For ceiling mounting, you need the ceiling mount kit designed for this
projector. When not mounted properly, the projector may fall, causing
hazards or injury. For details, consult your dealer. The warranty on
this projector does not cover any damage caused by use of any non-
recommened ceiling mount kit or installation of the ceiling mount kit in an
improper location.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Instructions
Moving the Projector
Use the handle grip when moving the projector.
Retract the adjustable feet to prevent damage to the lens
and cabinet when carrying.
When this projector is not in use for an extended period, put
it into a suitable case to protect the projector.
CAUTION IN CARRYING OR
TRANSPORTINGTHE PROJECTOR
– Do not drop or bump the projector, otherwise damages
or malfunctions may result.
– When carrying the projector, use a suitable carrying
case.
– Do not transport the projector by courier or any other
transport service in an unsuitable transport case. This
may cause damage to the projector. For information
about transporting the projector by courier or any other
transport service, consult your dealer.
– Do not put the projector in a case before it is cooled
enough.
Cautions in Handling the Projector
Do not hold the lens or the top cover when lifting or moving
the projector. Doing so may cause damage to the lens and
the projector.
Care must be taken when handling the projector; do not
drop, bump, subject it to strong forces, or put other things
on the cabinet.
Do not hold the lens and the peripheral part.
CAUTION
This projector has a motorized lens. Please note
the followings when using the projector.
L Do not touch the lens while it is moving as this
could cause injury to the fingers.
L Never allow children to touch the lens.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Compliance
Federal Communications Commission Notice
Multimedia Projector, Model: LV-7585
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1)This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
Note:This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
–
–
–
–
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Use of shielded cable is required to comply with class B limits in Subpart B of Part of FCC Rules.
Do not make any changes or modifications to the equipment unless otherwise specified in the instructions. If such changes or
modifications should be made, you could be required to stop operation of the equipment.
Canon U.S.A., Inc.
One Canon Plaza, Lake Success, NY 11042-1198, U.S.A.
Tel No. (516)328-5000
Canadian Radio Interference Regulations
This Class B digital apparatus complies with Canadian ICES-003.
AC POWER CORD REQUIREMENT
The AC Power Cord supplied with this projector meets the requirement for use in the country you purchased it.
AC Power Cord for the United States and Canada:
AC Power Cord used in the United States and Canada is listed by the Underwriters Laboratories
(UL) and certified by the Canadian Standard Association (CSA).
AC Power Cord has a grounding-type AC line plug. This is a safety feature to be sure that the
plug will fit into the power outlet. Do not try to defeat this safety feature. Should you be unable
to insert the plug into the outlet, contact your electrician.
GROUND
THE SOCKET-OUTLET SHOULD BE INSTALLED NEARTHE EQUIPMENT AND EASILY ACCESSIBLE.
European Union (and EEA) only.
This symbol indicates that this product is not to be disposed of with your household waste, according to the WEEE
Directive (2002/96/EC) and your national law. This product should be handed over to a designated collection point, e.g.,
on an authorized one-for-one basis when you buy a new similar product or to an authorized collection site for recycling
waste electrical and electronic equipment (EEE). Improper handling of this type of waste could have a possible
negative impact on the environment and human health due to potentially hazardous substances that are generally
associated with EEE. At the same time, your cooperation in the correct disposal of this product will contribute to
the effective usage of natural resources. For more information about where you can drop off your waste equipment
for recycling, please contact your local city office, waste authority, approved WEEE scheme or your household
waste disposal service. Your cooperation in the correct disposal of this product will contribute to the effective usage
of natural resources and will avoid incurring administrative sanctions according to art. 50 and following of Italian
legislative decree 22/97. For more information regarding return and recycling of WEEE products, please visit www.
canon-europe.com/environment.
(EEA: Norway, Iceland and Liechtenstein)
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Part Names and Functions
DꢃIndicators
JꢃTop Cover
8
Front
J
D
8 Top Cover Release Button
EꢃLens Cap
CAUTION
Do not turn on the projector with the lens
cap attached. High temperature from light
beam may damage the lens cap and result
in fire hazard.
GꢃInfrared Remote Receiver (Front)
L Projection Lens
HꢃLight-Block Sheet
< Adjustable Feet
B Air IntakeVent
ꢀ Filter Cover
ꢀ Lamp Cover
E
G
L
H
<
B
ꢀ
ꢀ
ꢀꢃExhaustVent
ꢀ
ꢀ
ꢀ
Back
CAUTION
Hot air is exhausted from the exhaust
vent. Do not put heat-sensitive objects
near this side.
ꢀ Terminals and Connectors
ꢀ Infrared Remote Receiver (Back)
ꢀ Power Cord Connector
ꢀ Optional Parts Attachment
ꢀꢃSide Controls
ꢀꢃHand Grip
ꢀ
ꢀ
ꢀ
<
Bottom
ꢀ
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Part Names and Functions
Rear Terminal
ꢀ
D
=
B
;
J
8
E
G
<
H
L
LꢃUSB CONNECTOR (Series B)
DꢃCOMPUTER INPUT TERMINAL (DIGITAL)
Connect the computer output digital signal to this
terminal. The HDTV (HDCP compatible) signal can
also be connected (pp.20-21).
Use this connector when controlling a computer
with the remote control unit of the projector.
Connect the USB terminal of your computer to this
connector with the supplied USB cable (p.20).
HꢃCONTROL PORT CONNECTOR
ꢀNote:
• Use a DVI-Digital cable which fits the width of the rear
terminal.
When controlling the projector from a computer,
connect the computer to this connector with a
control cable (p.20).
JꢃCOMPUTER INPUT TERMINAL (ANALOG)
Connect the computer (or RGB scart) output signal
to this terminal (pp.20-21).
<ꢃS-VIDEO INPUT JACK
Connect the S-VIDEO output signal from video
equipment to this jack (p.21).
8ꢃ5 BNC INPUT JACKS
Connect the component or composite video output
signal from video equipment to VIDEO/Y, Pb/Cb,
and Pr/Cr jacks or connect the computer output
signal (5 BNCType [Green, Blue, Red, Horiz. Sync,
and Vert. Sync.]) to G, B, R, H/V, and V jacks (pp.20–
21).
BꢃMONITOR OUT TERMINAL
This terminal can be used to output the incoming
analog RGB signal from INPUT 1-3 terminal to the
other monitor (pp.20-21).
ꢀꢃINFRARED REMOTE RECEIVER (Back)
The infrared remote receiver is also located in the
front (pp.10, 15).
EꢃVIDEO INPUT JACK
Connect the component or the composite video
output signal from video equipment to this jack
(p.21).
= Kensington Security Slot
This slot is for a Kensington lock used to deter theft of the
projector.
GꢃR/C JACK
*Kensington is a registered trademark of ACCO Brands Corporation.
When using the wired remote control unit, connect
the wired remote control unit to this jack with a
remote control cable (not supplied).
; RESET button
A built-in micro processor which controls this unit may
occasionally malfunction and need to be reset. This can
be done by pressing the RESET button with a pen, which
will shut down and restart the unit. Do not use the RESET
function excessively.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Part Names and Functions
Side Control and Indicators
Side Control
Indicators (on the top panel)
D
H
J
8
<
B
ꢀ
ꢀ
E
G
L
DꢃPOWER button
HꢃPOWER indicator
Turn the projector on or off (pp.23–24).
– Light when in stand-by mode and during
operations.
– Blink in the Power management mode (p.52).
JꢃINPUT button
Select an input source (pp.31–33).
<ꢃLAMP indicator
Light red during operations.
8ꢃLENS button
Enter the focus, zoom, and lens shift adjustment
mode (p.27).
BꢃLAMP REPLACE indicator
Light orange when the projection lamp reaches its
end of life (pp.59, 70).
EꢃPoint ! ꢀ buttons
– Select an item or adjust the value in the On-
Screen Menu (p.25).
– Pan the image in Digital zoom + mode (p.40).
ꢀꢃWARNING FILTER indicator
– Blink slow when the filter is being scrolled (pp.
56, 69).
– Blink fast when the filter scroll is not working
properly or the filter cartridge is not installed
(p.56, 70).
GꢃMENU button
Open or close the On-Screen Menu (p.25).
– Light orange when the clogging of the filter is
detected or the filter counter reaches a time set
in the timer setting, urging immediate filter/ filter
cartridge replacement (p.55, 56 70).
LꢃOK button
– Execute the selected item (p.25).
– Expand or compress the image in the Digital
zoom mode (p.40).
ꢀꢃWARNINGTEMP. indicator
Blink red when the internal temperature of the
projector exceeds the operating range (pp.63, 69-
70 ).
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Part Names and Functions
Remote Control Unit
8
J
D
E
G
ꢀ
L
H
ꢀ
ꢀ
B
<
B OK button
D STAND-BY button
– Execute the selected item (p.25).
– Expand or compress the image in the Digital
zoom mode (p.40).
Turn the projector off (p.24).
J WIRED REMOTE jack
Connect the remote control cable (not supplied)
to this jack when using as a wired remote control
unit.
ꢀ MOUSE POINTER button
Move a pointer of the projector or a pointer for
wireless mouse operation (p.30).
8 SIGNAL EMISSION indicator
Light red while a signal is being sent from the
remote control unit to the projector.
ꢀ NETWORK button
Select the Network input. (Optionally available).
E ON button
ꢀ L-CLICK button
Turn the projector on (p.23).
Act as the left mouse button for wireless mouse
operation (p.30).
G INPUT 1 – 3 buttons
Select an input source (INPUT 1 – INPUT 3)
(pp.31–33).
LꢃAUTO PC button
Automatically adjust the computer image to its
optimum setting (pp.28, 35).
To ensure safe operation, observe the following
precautions:
H FREEZE button
Freeze the picture on the screen (p.28).
– Do not bend, drop, or expose the remote control
unit to moisture or heat.
<ꢃPOINT ! ꢀ buttons
– For cleaning, use a soft dry cloth. Do not apply
benzene, thinner, splay, or any other chemical
materials.
– Select an item or adjust the value in the On-
Screen Menu (p.25).
– Pan the image in Digital zoom + mode (p.40).
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Part Names and Functions
Remote Control Unit
ꢌ
ꢀ
ꢀ
ꢌ
ꢌ
ꢌ
ꢌ
ꢀ
ꢀ
For PIN code
and remote
control code.
ꢌ
ꢌ
ꢀ
ꢀ
ꢌ
ꢀ
ꢌꢃKEYSTONE button
ꢀ MENU button
Correct keystone distortion (p.29).
Open or close the On-Screen Menu (p.25).
ꢌ LENS-SHIFT button
ꢀꢃP-TIMER button
Operate the P-timer function (p.29).
Select the Lens Shift function (p.28).
ꢀꢃD-ZOOM button
ꢌ ASPECT button
Select the Digital zoom +/- mode and resize the
image (p.40).
Select the screen size (p.28).
ꢌ R-CLICK button
ꢀꢃZOOM ! buttons
Act as the right mouse button for wireless mouse
operation (p.30).
Zoom in and out the images (p.28).
ꢀꢃINFO. button
ꢌ POINTER button
Display the input source information (p.28).
Act as the On-Off switch for the Pointer (p.29, 30).
ꢀꢃFILTER button
ꢌ NUMBER buttons
Scroll the filter (p.29).
Act as number buttons. Use these buttons when
setting the remote control codes (p.16) or when
entering the PIN code numbers (pp. 23, 50, 51, 54).
ꢀ RESET/ON/ALL-OFF switch
When using the remote control unit, set this switch
to “ON.” Set it to “ALL OFF” for power saving when it
is not in use. Slide this switch to “RESET” to initialize
the remote control code.
ꢌꢃFOCUS buttons
Adjust the focus (p.28).
ꢌꢃBLANK button
Temporarily turn off the image on the screen (p.29).
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Part Names and Functions
Remote Control Battery Installation
Open the battery
compartment lid.
Install new batteries into
the compartment.
Replace the
compartment lid.
1
2
3
Press the lid downward and
slide it.
Two AAA size batteries
For correct polarity (+ and –),
be sure battery terminals are
in contact with pins in the
compartment.
To insure safe operation, please observe the following precautions :
L Use two (2) AAA or LR03 type alkaline batteries.
L Always replace batteries in sets.
L Do not use a new battery with a used battery.
L Avoid contact with water or liquid.
L Do not expose the remote control unit to moisture or heat.
L Do not drop the remote control unit.
L If the battery has leaked on the remote control unit, carefully
wipe the case clean and install new batteries.
L Risk of an explosion if battery is replaced by an incorrect type.
L Dispose of used batteries according to the instructions.
Remote Control Receivers and Operating Range
16.4’
(5 m)
Point the remote control unit toward the projector (to
Infrared Remote Receivers) when pressing the buttons.
Maximum operating range for the remote control unit is
about 16.4’ (5 m) and 60 degrees in front and rear of the
projector.
Infrared Remote Receivers are provided both in front and
back of the projector. You can conveniently use both of
the receivers (pp. 10, 51).
16.4’
(5 m)
Wired Remote Control Transmitter
The remote control unit can be used as a wired remote control unit.
Wired remote control unit helps you use the remote control unit
outside of the operating range (16.4’/ 5 m). Connect the remote
control unit and the projector with the remote control cable (sold
separately). Connected with the remote control cable, the remote
control unit does not emit wireless signal.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Part Names and Functions
Remote Control Code
The eight different remote control codes (Code 1–Code 8) are assigned to this projector. Switching the
remote control codes prevents interference from other remote control units when several projectors or video
equipment next to each other are operated at the same time. Change the remote control code for the projector
first before changing that for the remote control unit. See “Remote control” in the Setting Menu on page 51.
Press and hold the MENU and a number button (1–8)
for more than 5 seconds to switch between the codes.
1
To initialize the remote control code, slide the RESET/
ON/ALL-OFF switch to “RESET,” and then to “ON.”The
initial code is set to Code 1.
2
MENU button
Number buttons
RESET/ON/ALL
OFF Switch
Press and hold the MENU and a number button
(1–8) that corresponds to the remote control code
for more than 5 seconds to switch between the
codes.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Positioning the Projector
For projector positioning, see the figures below. The projector should be set perpendicularly to the plane of the
screen.
ꢀNotes:
• The brightness in the room has a great influence on picture quality. It is recommended to limit
ambient lighting in order to obtain the best image.
• All measurements are approximate and may vary from the actual sizes.
(Inch Diagonal)
48.2’ (14.7m)
36.1’ (11.0m)
Max. Zoom
Min. Zoom
400”
308”
24.0’ (7.3m)
11.8’ (3.6m)
300”
231”
4.6’ (1.4m)
200”
154”
100”
77”
40”
31”
(Center)
40”
100”
200”
300”
400”
Screen Size
(W x H) mm
813 x 610
5.9’ (1.8 m)
4.6’ (1.4 m)
2032 x 1524
15.4’ (4.7 m)
11.8’ (3.6 m)
4064 x 3048
6096 x 4572
46.6’ (14.2 m)
36.1’ (11.0 m)
8128 x 6096
–––––
Zoom (min.)
Zoom (max.)
30.8’ (9.4 m)
24.0’ (7.3 m)
48.2’ (14.7 m)
Adjustable Feet
Projection angle can be adjusted up to 6.5 degrees with the
adjustable feet.
Rotate the adjustable feet and tilt the projector to the proper
height; to raise the projector, rotate the both feet clockwise.
To lower the projector or to retract the adjustable feet, rotate the
both feet counterclockwise.
To correct keystone distortion, press the KEYSTONE button on the
remote control unit or select Keystone from the menu (see pages
14, 29, 40, 44).
ADJUSTABLE FEET
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Lens Installation
When replacing the lens or using an optional lens, install the lens by following the instructions below. Ask the
sales dealer for detailed information of the optional lens specifications.
Top cover release button
Removing the lens
Top cover
Shift the lens to the center position by using the
1
Lens shift function (p. 27).
While pressing the top cover release button on
the top cover, slide the top cover toward front to
remove it
2
Slide the light-block sheet upward and remove it.
3
4
Hold the lens with one hand and pull the Lens
Lock Lever upward with the other hand. Remove
the lens from the projector.
Light-block sheet
=Do not touch the glass part of the lens with your
hand.
CAUTION
Be careful when handling the lens. Do not
drop.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Attaching the lens to the projector
Fit the lens to the projector. Make sure that the
lens is fully inserted to the projector.
1
Push the Lens Lock Lever downward. Make sure
that the lens is properly locked.
2
Slide the light-block sheet in the groove to mount.
3
While pressing the top cover release button on the
top cover, slide the top cover back to the projector.
4
Groove
NOTES ON LENS INSTALLATION
L Do not touch or remove any parts except the lens and related parts. It may result in
malfunctions, electrical shock, fire hazard or other accidents.
L Before installing or replacing the lens, check that the Model No. of the Projection Lens
matches to the projector.
L For details of the lens and installation, contact the sales dealer where you purchased the
projector.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Connecting to a Computer (Digital and Analog RGB)
Cables used for connection (= = Cables not supplied with this projector.)
• VGA Cable (One cable is supplied.)
• DVI-Digital Cable =
• BNC Cable =
• Serial Cross Cable=
• USB Cable
USB port
Monitor Output
Monitor Output
Monitor Output
Monitor Input
Serial out
V
USB
cable
DVI-Digital
cable
VGA
cable
VGA
cable
Serial Cross
cable
BNC
cable
USB
G
B
R
H/V V
DIGITAL IN
ANALOG IN
MONITOR OUT
CONTROL PORT
Unplug the power cords of both the
projector and external equipment from
the AC outlet before connecting cables.
V
See the next page for the signals that can output to the
MONITOR OUT terminal.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Connecting to Video Equipment (Video, S-Video)
Cables used for connection (= = Cables not supplied with this projector.)
Monitor Out SignalTable
• Video Cable (RCA x 1 or RCA x 3) =
• BNC Cable =
InputTerminal
Monitor Out
YES
Cable
• S-VIDEO Cable =
• Scart-VGA Cable =
RGB (PC analog)
D-sub15
DVI-D
RGB (SCART)
RGB (PC digital)
RGB (AV HDCP)
RGB
NO
NO
NO
YES
Input 1
1
A cable with one
end D-sub 15 and
the other end (Black
box) compatible with
each equipment is
necessary.
Video
Y, Cb/Cr
Y, Cb/Cr
S-video
YES
YES
YES
NO
YES
NO
Input 2 5BNC
1
1
1
Unplug the power cords
of both the projector
and external equipment
from the AC outlet before
connecting cables.
RCA
Input 3 S-Video
Video
Video
1
Network
Component Video
Digital Output
S-video
Output
Output
RGB Scart
21-pin Output
(HDCP
Component Video
Output
Composite Video
(Y, Pb/Cb, Cr/Pr) Composite Video
compatible)
Refer to the
Monitor Out
SignalTable
(above).
S-video
cable
RCA
cable
BNC
cable
DVI-Digital
cable
Scart-VGA
cable
Y - Pb/Cb - Pr/Cr
Y - Pb/Cb - Pr/Cr
Video
Video
DIGITAL IN
ANALOG IN
MONITOR OUT
S-VIDEO
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Connecting the AC Power Cord
This projector uses nominal input voltages of 100–120 V or 200–
240 V AC and it automatically selects the correct input voltage. It
is designed to work with single-phase power systems having a
grounded neutral conductor. To reduce the risk of electrical shock,
do not plug into any other type of power system.
If you are not sure of the type of power being supplied, consult
your authorized dealer or service station.
Connect the projector with all peripheral equipment before turning
on the projector.
CAUTION
For safety, unplug the AC power cord when the projector is not
in use. When the projector is connected to an outlet with AC
power cord, it is in stand-by mode and consumes a little electric
power.
Connect the AC power cord (supplied) to the
projector.
The AC outlet must be near this equipment and
must be easily accessible.
NOTE ONTHE POWER CORD
AC power cord must meet the requirements of the country where you use the projector.
Confirm the AC plug type with the chart below and proper AC power cord must be used.
If the supplied AC power cord does not match your AC outlet, contact your sales dealer.
Projector side
AC Outlet side
For the U.S.A. and Canada
For Continental Europe
For the U.K.
Ground
To POWER CORD
CONNECTOR on your
projector.
To the AC Outlet.
(120V AC)
To the AC Outlet.
(200–240V AC)
To the AC Outlet.
(200–240V AC)
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operation
Turning On the Projector
Complete peripheral connections (with a computer,
VCR, etc.) before turning on the projector.
16
1
2
Connect the projector’s AC power cord into an AC
outlet. The LAMP indicator lights red and the POWER
indicator lights green.
Press the POWER button on the side control or the
ON button on the remote control unit. The LAMP
indicator dims and the cooling fans start to operate.
The preparation display appears on the screen and the
countdown starts.
3
The preparation display will disappear after 30
seconds.
Selected Input Source and Lamp mode
After the countdown, the input source that was
selected the last time and the Lamp mode status icon
(see page 51) appear on the screen.
4
Lamp mode status
See page 51 for the Lamp mode status
If the projector is locked with a PIN code, PIN code
Input Dialog Box will appear. Enter the PIN code as
instructed below.
ꢀNote:
• The Lamp replacement icon and the Filter
replacement or the Filter cartridge replacement
icon may appear on the screen depending on the
usage state of the projector.
Enter a PIN code
Use the Point ! buttons on the side control or Number
buttons on the remote control unit to enter a number.
• When the filter cartridge replacement icon
keeps appearing on the screen at turning on the
projector for some time and no action is taken
to replace the filter cartridge, the projector will
be automatically shut down in 3 minutes after
turning on to protect the projector. (pp. 56-58, 70)
When using side control
Use the Point ! buttons on the side control to select a
number. Press the Point button to fix the number and
move the red frame pointer to the next box. The number
changes to “3.” Repeat this step to complete entering a
four-digit number. After entering the four-digit number, move
the pointer to “Set.” Press the OK button so that you can
start to operate the projector.
PIN code Input Dialog Box
When using remote control unit
After the OK icon
disappears, you can
operate the projector.
Press the Number buttons on the remote control unit to
enter a number (p.14). When you complete entering a four-
digit number, the pointer moves to “Set.” Press the OK
button so that you can start to operate the projector.
ꢀNote:
• When the Logo select function is set to “Off,” the
logo will not be shown on the screen (p.49).
• When the “Countdown off” or “Off” is selected
in the Display function, the countdown will not
be shown on the screen (p.48).
• During the countdown period, all operations are
invalid.
• If the correct PIN code number is not entered
within three minutes after the PIN code dialog
box appeared, the projector will be turned off
automatically.
If you fixed an incorrect number, use the Point ꢀ button to
move the pointer to the number you want to correct, and
then enter the correct number.
If you entered an incorrect PIN code, “PIN code” and the
number (3333) will turn red for a moment. Enter the
correct PIN code all over again.
What is PIN code?
• The “1234” is set as the initial PIN code at the
factory.
PIN (Personal Identification Number) code is a security
code that allows the person who knows it to operate the
projector. Setting a PIN code prevents unauthorized use of
the projector.
A PIN code consists of a four-digit number. Refer to the PIN
code lock function in the Setting Menu on page 53-54 for
locking operation of the projector with your PIN code.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operation
Turning Off the Projector
Press the POWER button on the side control or the
STAND-BY button on the remote control unit, and
“Power off?” appears on the screen.
1
2
Press the POWER button on the side control or the
STAND-BY button on the remote control unit again to
turn off the projector. The LAMP indicator lights bright
and the POWER indicator turns off. After the projector
is turned off, the cooling fans operate for 90 seconds.
You cannot turn on the projector during this cooling
down period.
“Power off?” disappears after 4 seconds.
When the projector has cooled down enough, the
POWER indicator lights green and then you can turn on
the projector. To unplug the AC power cord, wait until
the projector is completely cooled down.
3
TO MAINTAINTHE LIFE OFTHE LAMP, ONCEYOU
TURNTHE PROJECTOR ON, WAIT AT LEAST FIVE
MINUTES BEFORETURNING IT OFF.
DO NOT UNPLUGTHE AC POWER CORD WHILE
COOLING FANS ARE RUNNING OR BEFORETHE
POWER INDICATOR LIGHTS GREEN AGAIN.
OTHERWISE IT WILL RESULT IN SHORTENING OF
THE LAMP LIFE.
DO NOT OPERATETHE PROJECTOR CONTINUOUSLY
WITHOUT REST. CONTINUOUS USE MAY RESULT
IN SHORTENINGTHE LAMP LIFE. TURN OFFTHE
PROJECTOR AND LET STAND FOR ABOUT AN HOUR
IN EVERY 24 HOURS.
ꢀNote:
• When the On start function is set to “On,” the projector will be
turned on automatically by connecting the AC power cord to an AC
outlet (p.52).
• The running speed of cooling fans is changed according to the
temperature inside the projector.
• Do not put the projector in a case before the projector is cooled
enough.
• If the WARNINGTEMP. indicator blinks red, see “Warning
Indicators” on page 63.
• The projector cannot be turned on during the cooling period with
the POWER indicator turned off.You can turn it on again after the
POWER indicator becomes green again.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operation
How to Operate the On-Screen Menu
The projector can be adjusted or set via the On-Screen
Menu. For each adjustment and setting procedure, refer to
the respective sections in this manual.
Side Control
Press the MENU button on the side control or the
remote control unit to display the On-Screen Menu.
POINT buttons
1
Use the Point ꢀ buttons to select a Menu icon. Use
the Point ! buttons to select an item in the selected
menu.
2
OK button
MENU button
Press the OK button to show the item data. Use the
Point ꢀ buttons to adjust the values.
3
Remote Control Unit
To close the On-Screen Menu, press the MENU button
again.
POINT buttons
OK button
ꢀNote:
• The selected item is not active until the OK button is pressed.
MENU button
On-Screen Menu
Menu icon
Pointer
Menu bar
Pointer (red frame )
(red frame)
Press the Point ! buttons
to move the pointer.
Item
OK
button
Item data
Press the Point ꢀ
buttons to adjust the
value.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operation
Menu Bar
For detailed functions of each menu, see “MenuTree” on pages 66-68.
For Computer Source
Information Menu
Image Select Menu
Screen Menu
Display the input
source information
(p. 28).
Used to select
an image level
among Standard,
High contrast, and
Custom 1–10 (p.38). Digital zoom +/–] (pp.39-40).
Used to adjust the size of
the image. [Normal/True/
Wide/Full screen/Custom/
Keystone/Ceiling/Rear/Reset/
GuideWindow
PC System Menu
Show the selected Used to select
Menu of the On-
Screen Menu.
computer system
(p. 34).
Image Adjust Menu
Input Menu
PC Adjust Menu
Setting Menu
Used to adjust the
computer image.
Used to select an
input source (Input
1, Input 2, or Input 3) to match with the
Used to adjust
the parameters
Used to set
the projector’s
operating
configurations
(pp. 48–55).
[Contrast/ Brightness/Color
management/Auto picture
control/Color temp./White
balance (R/G/B)/Offset (R/
G/B)/Sharpness/ Gamma/
Reset/Store/Quit]
(pp. 31, 32).
input signal format
(pp. 35–37).
(pp. 45–47).
For Video Source
Screen Menu
Input Menu
Image Select Menu
Used to adjust the
size of the image.
[Normal/Wide/Custom/
Keystone/Ceiling/Rear/
Reset] (pp. 43-44).
Used to select
an input source
(Input 1, Input 2,
or Input 3)
Used to select an
image level among
Standard, Cinema, and
Custom 1–10
(pp.31, 33).
(p. 42).
AV System Menu
Image Adjust Menu
Same function as menu
for Computer Source.
Same function as menu
for Computer Source.
Used to select the
system of selected
video source
Used to adjust the picture
image. [Contrast/Brightness/
Color/Tint/Color management/
Auto picture control/Color temp./
White balance (R/G/B)/ Offset
(R/G/B)/Sharpness/Gamma/Noise
reduction/Progressive/Reset/
Store/Quit]
(p. 41).
(pp. 45–47.)
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operation
Operating with Projector Control
Lens Operation
The following lens operation can be made with the Lens
button on the side control.
Side Control
LENS button
Press the LENS button to enter each lens operation mode.
The selected adjustment display appears on the screen.
Zoom
Focus
POINT buttons
Lens Shift
Zoom Adjustment
Display “Zoom” on the screen. Use the Point ! buttons
to zoom in and out the image.
ZOOM
Focus Adjustment
Display “Focus” on the screen. Use the Point ! buttons
to adjust focus of the image.
FOCUS
Lens Shift Adjustment
Display “Lens shift” on the screen. Use the Point ! ꢀ
buttons to position the screen to the desired point without
having picture distortion.
The screen can be moved up or down to 50 percent, or
sideways up to 10 percent from the central axis of the
lens shift.
ꢀNote:
• The arrow disappears at the maximum lens shift
in each direction.
• The arrow turns red when the lens shift comes to
the center position of the screen.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operation
Operating with Remote Control Unit
Using the remote control unit for some frequently used operations is advisable. Just pressing one of the
buttons enables you to make the desired operation quickly without calling up the On-Screen Menu.
FREEZE button
Press the FREEZE button on the remote control unit to
freeze the picture on the screen. To cancel the FREEZE
function, press the FREEZE button again or press any other
button.
Remote Control Unit
AUTO PC button
AUTO PC
button
FREEZE button
Press the AUTO PC button on the remote control unit to
operate the Auto PC Adj. function. The computer screen
adjustment can be done easily by pressing this button. See
page 35 for details.
POINT ! ꢀ
buttons
D-ZOOM button
Press the D-ZOOM button on the remote control unit to
enter to the Digital zoom +/– mode. See page 40 for details.
D-ZOOM
button
ASPECT button
LENS-SHIFT
button
ASPECT button
ZOOM
buttons
Press the ASPECT button on the remote control unit to
select the desired screen size. The selected screen size
symbol appears on the screen for 4 seconds. See pages 39
to 40 and 43 to 44 for details.
INFO.
button
FOCUS
buttons
Press and hold the ASPECT button for more than 5 seconds
to return all the screen size adjustment setting to the factory
default setting.
ꢀNote:
• See the next page for the description
of other buttons.
LENS-SHIFT button
See page 27 for details.
ZOOM buttons
Press the ZOOM buttons on the remote control unit to zoom
in and out the image.
Information Menu
FOCUS buttons
Press the FOCUS buttons on the remote control unit to
adjust focus of the image.
Information Menu
INFO. button
Information display can be used to confirm the current
operating condition of the projector and the signal being
projected through the projector.
Press the INFO. button on the remote control unit to
display the information window on the screen. To hide the
information window, press the INFO. button again or Point ꢀ
buttons.
The information window can also be selected from the
menu.
*The H- and V-sync freq. values described in this figure
may be different from the actual values.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operation
Remote Control Unit
FILTER button
Press and hold the FILTER button for more than 5 seconds
to operate electrically operated filter to replace the filter.
ꢀNote:
• When the filter is replaced, the total accumulated time of the filter
use is automatically set to 0.
BLANK button
MOUSE
POINTER
button
Press the BLANK button on the remote control unit to black
out the image. To restore to normal, press the BLANK button
again or press any other button.
POINTER
button
P-TIMER
button
KEYSTONE
button
BLANK
button
FILTER
button
“Blank” disappears after 4 seconds.
MOUSE POINTER button
Move the pointer on the screen with this button.
ꢀNote:
• See the previous page for the
description of other buttons.
POINTER button
Press POINTER button on the remote control unit to display
the Pointer on the screen.
P-TIMER button
Press the P-TIMER button on the remote control unit. The
Timer display “00 : 00” appears on the screen and starts to
count time (00 : 00–59 : 59).
To stop the P-TIMER, press the P-TIMER button.
To cancel the P-TIMER, press the P-TIMER button again.
P-Timer display
KEYSTONE button
Press the KEYSTONE button on the remote control unit. The
“Keystone” appears on the screen.
• The white arrows indicate that there is no correction.
• A red arrow indicates the direction of correction.
• An arrow disappears at the maximum correction.
• If you press the KEYSTONE button on the remote
control unit again while the Keystone dialog box is
being displayed, the keystone adjustment will be
canceled.
Use the Point ! ꢀ buttons to correct keystone
distortion. The keystone adjustment can be stored (pp.40,
44).
• “Keystone” disappears after 10 seconds.
Reduce the upper width with
Point ! button.
Reduce the lower width
with Point button.
Reduce the left part with
Point ꢀ button.
Reduce the right part with
Point button.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operation
Pointer Function
You can move the Pointer of the projector with the remote control unit to emphasize a part of the projected
image.
Press the POINTER button to activate the Pointer
function.
1
MOUSE POINTER button
Use the MOUSE POINTER button to move the Pointer.
2
POINTER button
To cancel the Pointer function, press the POINTER
button again or press any other button.
3
Pointer
ꢀNote:
• You can choose the pattern of Pointer (Arrow/Cross/Dot) in the
Setting Menu (p. 52)
Wireless Mouse Operation
The remote control unit can be used as a wireless mouse for your computer.
Before operating the wireless mouse, connect your
computer and the projector with the supplied USB
cable (p. 20).
1
MOUSE POINTER
button
Move the pointer on
the screen with this
button.
When the Pointer function is used, the wireless mouse
is not available.
When a USB cable is connected to the computer
and the projector, turn on the projector first, then
the computer. If you turn on the computer first, the
wireless mouse function may not operate properly.
2
R-CLICK button
Acts as right (click)
mouse button while
the projector and
a computer are
connected with a USB
cable.
L-CLICK button
Acts as left (click)
mouse button while
the projector and
a computer are
connected with a USB
cable.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Input Selection
Input
Side Control
Side Control button operation
INPUT button
INPUT button
Input 1
Input 2
Input 3
Side Control Operation
Press the INPUT button on the side control. It switches to
INPUT 1, INPUT 2, and INPUT 3 as you press the INPUT
button.
Before using the INPUT button on the side control, you
must select a correct input source by On-Screen Menu and
the latest input source will be displayed.
Remote Control button operation
INPUT 1 button
Input 1
Remote Control Unit
RGB (PC analog)
RGB (Scart)
RGB (PC digital)
RGB (AV HDCP)
INPUT buttons
INPUT 2 button
Remote Control Operation
Input 2
Video
Press the INPUT 1, INPUT 2, or INPUT 3 buttons on the
remote control unit. The input source appears on the screen
as you press each button. Select the connected input
source.
Y,Pb/Cb,Pr/Cr
RGB
INPUT 3 button
Input 3
Video
Y,Pb/Cb,Pr/Cr
S-video
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Input Selection
Computer Input Source Selection
Menu Operation
WHEN SELECTING INPUT 1 (COMPUTER INPUTTERMINALS )
Press the MENU button to display the On-Screen Menu. Use
the Point ꢀ buttons to move the red frame pointer to the
INPUT Menu icon.
INPUT MENU
1
2
3
Input Menu icon
Use the Point ! buttons to move the red arrow pointer to
the desired input and then press the OK button. The Source
Select Menu appears.
Move the pointer (red arrow) to Input
1 and press the OK button.
Use the Point ! buttons to select the desired source and
then press the OK button.
Input 1
RGB (PC analog)
When your computer is connected to the INPUT 1 (ANALOG)
terminal, select RGB (PC analog).
Source Select Menu
Move the pointer (red
arrow) to the desired source
and press the OK button.
RGB (PC digital)
When your computer is connected to INPUT 1 (DIGITAL)
terminal, select RGB (PC digital).
ꢀNote:
• INPUT SOURCE changes if the INPUT 1 button on the remote
control unit is pressed.
• HDCP (High-bandwidth Digital Content Protection) is a system
for protecting digital entertainment content which is delivered by
DVI (Digital Visual Interface) from being copied.The specification
of HDCP is decided and controlled by Digital Content Protection,
LLC. Should the specification be changed, this projector may not
display the digital content protected by HDCP.
WHEN SELECTING INPUT 2 (5 BNC INPUT JACKS )
INPUT MENU
When connecting the computer output [5 BNCType (Green,
Blue, Red, Horiz. Sync, and Vert. Sync.)] from the computer
to G, B, R, H/HV, and V jacks:
INPUT Menu icon
Move the pointer (red arrow) to Input
2 and press the OK button.
RGB
When your computer is connected to the INPUT 2 (5 BNC
INPUT JACKS) terminal, select RGB.
Input 2
Source Select Menu
Move the pointer (red
arrow) to RGB and press the
OK button.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Input Selection
Video Input Source Selection
Menu Operation
WHEN SELECTING INPUT 1 (COMPUTER INPUTTERMINALS )
INPUT MENU
When connecting to video equipment, select the type of
Video source in the Source Select Menu.
Input Menu icon
RGB (Scart)
When scart video equipment is connected to the INPUT 1
(ANALOG) terminal, select RGB (Scart).
Move the pointer (red arrow) to Input
1 and press the OK button.
RGB (AV HDCP)
Input 1
If the HDCP-compatible signal source is connected to the
INPUT 1 (DIGITAL) terminal, select RGB (AV HDCP).
Source Select Menu
Move the pointer (red
arrow) to RGB (Scart) or
RGB (AV HDCP) and press
the OK button.
WHEN SELECTING INPUT 2 (5 BNC INPUT JACKS )
INPUT MENU
When connecting to video equipment, select the type of
Video source in the Source Select Menu.
Input Menu icon
When the video input signal is connected to the
Video
VIDEO jack, select Video.
Move the pointer (red arrow) to Input
2 and press the OK button.
When the video input signal is connected to theY-
Pb/Cb-Pr/Cr jacks, selectY, Pb/Cb, Pr/Cr.
Y, Pb/Cb, Pr/Cr
Input 2
Source Select Menu
Move the pointer (red
arrow) to Video orY, Pb/Cb,
Pr/Cr and press the OK
button.
WHEN SELECTING INPUT 3 (AVTERMINALS )
INPUT MENU
When connecting to video equipment, select the type of
Video source in the Source Select Menu.
Input Menu icon
When the video input signal is connected to the
VIDEO jack, select Video.
Video
Move the pointer (red arrow) to Input
3 and press the OK button.
When the video input signal is connected to theY-
Pb/Cb-Pr/Cr jacks, selectY, Pb/Cb, Pr/Cr.
Y, Pb/Cb, Pr/Cr
Input 3
When the video input signal is connected to the S-
VIDEO jack, select S-Video.
S-Video
Source Select Menu
Move the pointer (red
arrow) to the desired source
and press the OK button.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Input
Computer System Selection
Automatic Multi-Scan System
This projector automatically tunes to various types of computers based on VGA, SVGA, XGA, SXGA, SXGA+,
WXGA, or UXGA (refer to “Compatible Computer Specifications” on pages 71–72). If a computer is selected
as a signal source, this projector automatically detects the signal format and tunes to project a proper image
without any additional settings. (Some computers need to be set manually.)
One of the following messages may appear when:
The projector cannot recognize the connected signal
conforming to the provided PC Systems. The “Auto” is
Auto
PC SYSTEM MENU
displayed on the System Menu box and the Auto PC
Adjustment function works to display proper images.
If the image is not projected properly, a manual
adjustment is required. (pp. 36–37.)
PC System Menu icon
Selected system is displayed.
There is no signal input from the computer. Check the
connection between your computer and the projector.
(See “Troubleshooting” on page 64.)
-----
The preset system is manually adjustted in the PC
Adjust Menu. The adjusted data can be stored in the
Mode 1–10. (pp. 36-37)
Mode 1
SVGA 1
PC systems provided in this projector is chosen. The
projector chooses a proper system provided in the
projector and displays it.
= Mode 1 and SVGA 1 are examples.
PC SYSTEM MENU
Selecting Computer System Manually
PC system can also be selected manually.
PC System Menu icon
Selected system is displayed
Press the MENU button to display the On-Screen Menu. Use
1
the Point ꢀ buttons to move the red frame pointer to the
PC System Menu icon.
Systems in this dialog box can be
selected.
Use the Point ! buttons to move the red arrow pointer to
the desired system, and then press OK button.
Custom Mode (1–10) set in PC Adjust
Menu. (pp.36–37)
2
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Input
Auto PC Adjustment
Auto PC Adjustment function is provided to automatically adjust Fine sync, Total dots, Horizontal and Vertical
positions to conform to your computer.
Direct Operation
Remote Control Unit
The Auto PC adjustment function can be operated directly
by pressing the AUTO PC button on the remote control unit.
AUTO PC button
Menu Operation
Auto PC adj.
Press the MENU button to display the On-Screen Menu. Use
PC ADJUST MENU
1
the Point ꢀ
buttons to move the red frame pointer to the
PC Adjust Menu icon.
Use the Point ! buttons to move the red frame pointer to
the AUTO PC adj. icon and then press the OK button twice.
PC Adjust Menu icon
2
Move the red frame pointer to the Auto PC
adj. and press the OK button twice.
“Please wait...” appears while the Auto PC
adjustment is in process.
To store the adjusted parameters.
The adjusted parameters from the Auto PC Adjustment can be stored in
the projector. Once the parameters are stored, the setting can be done
just by selecting Mode in PC SYSTEM Menu (p.34). See MANUAL PC
ADJUSTMENT on pages 36–37.
ꢀNote:
• Fine sync, Total dots, Horizontal and Vertical position of certain
computers cannot be fully adjusted with the Auto PC Adjustment
function. When the image is not provided properly with this
operation, manual adjustments are required. (pp. 36–37.)
• Auto PC Adjustment cannot be operated in Digital Signal Input on
the DVI terminal and “480p,” “575p,” “480i,” “575i,” “720p,” “1035i,”
or “1080i” is selected on the PC SYSTEM Menu.
• Depending on the condition of signals and the type and
length of cables, the signals may not be properly viewed.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Input
Manual PC Adjustment
Some computers employ special signal formats which may not be tuned by Multi-Scan system of this projector.
Manual PC Adjustment enables you to precisely adjust several parameters to match those special signal formats.
The projector has 10 independent memory areas to store those parameters manually adjusted. It allows you to
recall the setting for a specific computer.
ꢀNote: The PC Adjust Menu cannot be operated when the digital signal input on the DVI terminal is selected on
PC System Menu.
Press the MENU button to display the On-Screen Menu. Use
the Point ꢀ buttons to move the red frame pointer to the
PC Adjust Menu icon.
1
PC ADJUST MENU
Use the Point ! buttons to move the red frame pointer to
the desired item and then press the OK button to display the
adjustment dialog box. Use the Point ꢀ buttons to adjust
2
PC Adjust Menu icon
the setting value.
Move the red frame pointer to the
desired item and press the OK button.
Fine sync
Use the Point ꢀ buttons to adjust the value, eliminating a flicker
from the image displayed (from 0 to 31).
Status (Stored/Free) of the
Selected Mode.
Total dots
Use the Point ꢀ buttons to adjust the number of total dots in one
horizontal period to match your PC image.
Selected Mode
Position H
Use the Point ꢀ buttons to adjust the horizontal picture position.
Press the Point ꢀ buttons to adjust
the value.
Press the OK button at this icon to
adjust “Clamp,” “Display area H,” or
“Display area V.”
PositionV
Use the Point ꢀ buttons to adjust the vertical picture position.
Current mode
Press the OK button to show H-sync freq. and V-sync freq. of the
connected computer.
Current mode
Clamp
Use the Point ꢀ
buttons to adjust the clamp level. When the
image has dark bars, try this adjustment.
Display area H
Press the OK button at
Current mode icon to
show the information
of the connected
computer.
Use the Point ꢀ
buttons to adjust the horizontal area displayed
by this projector.
Display areaV
Press the OK button at this icon to
display the previous items.
Use the Point ꢀ buttons to adjusts the vertical area displayed by
this projector.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Input
Reset
To reset the adjusted data, select Reset and press the OK button. A
confirmation box appears and then select [Yes]. All adjustments will
return to their previous figures.
Mode free
To clear the adjusted data.
To clear the adjusted data, select Mode free and then press the OK
button. Move the red arrow pointer to the Mode that you want to
clear and then press the OK button.
Store
To store the adjusted data, select Store and then press the OK
button. Move the red arrow pointer to one of the Mode 1 to 10 in
which you want to store, and then press the OK button.
Close this dialog box.
Quit
Confirmation box appears
and then select [Yes].
Exit the PC Adjust Menu.
To store the adjusted data.
This Mode has stored parameters.
Close this dialog box.
Vacant
Values of “Total dots,” “Position
H,” “Position V,” “Display area
H,” and “Display area V.”
Confirmation box appears
and then select [Yes].
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Input
Image Level Selection
Menu Operation
Press the MENU button to display the On-Screen Menu. Use
the Point ꢀ buttons to move the red frame pointer to the
Image Select Menu icon.
IMAGE SELECT MENU
1
Use the Point ! buttons to move the red frame pointer to
the desired image level and then press the OK button.
2
Image Select Menu icon
Standard
Move the red frame pointer to the desired
level and press the OK button.
Normal picture level preset on the projector.
High contrast
Picture level with improved halftone for graphics.
Custom 1–10
User preset picture adjustment in the Image Adjust Menu. (p. 47)
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Input
Screen Size Adjustment
Select the desired screen size that conforms to the input signal source.
Press the MENU button to display the On-Screen Menu. Use
the Point ꢀ buttons to move the red frame pointer to the
Screen Menu icon.
SCREEN MENU
1
2
Use the Point ! buttons to move the red frame pointer to
the desired function and then press the OK button.
Screen Menu icon
Move the red frame pointer to the desired
function and press the OK button.
Normal
Provide the image at the normal computer aspect ratio of 4:3.
True
Provide the image in its original size. When the original image size
is larger than the screen size (1024 x 768), the projector enters to
ꢀNote:
the panning mode automatically. Use the Point ! ꢀ buttons
to pan the image. When adjusted, the arrows will turn red. When
reached to the correction limits, the arrows will disappear.
• The projector cannot display any resolution
higher than 1600 x 1200. If your computer’s
screen resolution is higher than 1600 x 1200,
lower the resolution before connecting the
projector.
• The image data other than XGA (1024 x 768) is
modified to fit the screen size in initial mode.
• True, Full screen, and Digital zoom +/– cannot
be selected when no signal is detected in the PC
System Menu. (p.34)
Wide
Provide the image to fit the wide video aspect ratio (16:9) by
expanding the image width uniformly. This function can be used to
provide the squeezed video signal at 16:9.
Full screen
Provides the full screen image.
Custom
Adjust the screen scale and position manually with this function.
Press the OK button at Custom and the “Custom” is displayed on
the screen for a few seconds. To display the Aspect dialog box,
press the OK button at Custom again and then the Aspect dialog
box appears.
Scale H/V.............. Adjust the Horizontal/Vertical screen scale.
H&V...................... When set to “On,” the aspect ratio is fixed.
The “Scale V” appears dimmed and becomes
unavailable. Adjust “Scale H,” then the screen
scale is automatically modified based on the
aspect ratio.
Position H/V.......... Adjust the Horizontal/Vertical screen position.
Common .............. Save the adjusted scale to all the inputs.
Press the OK button at Common to display a
confirmation box. To save the scale, press the
OK button at “Yes.” When Custom is selected,
the saved scale is used.
Reset.................... Reset the all adjusted values. Press the OK
button at Reset to display a confirmation box.
To reset, press the OK button at “Yes.”
Press the OK button at Common or Reset,
to display a confirmation box.
ꢀNote:
• When no signal is detected, “Normal” is
set automatically and the Aspect dialog box
disappears.
• The adjustable range for Scale H/V and Position
H/V is limited depending on the input signal.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Input
Keystone
SCREEN MENU
This function is used to store or reset the keystone correction
when the AC power cord is unplugged. Use the Point ꢀ buttons
to switch between each option.
Store. . . Keep the keystone correction even when the AC power
cord is unplugged.
Reset . . Release the keystone correction when the AC power
cord is unplugged.
Move the red frame pointer to the desired
function and press the OK button.
To correct keystone distortion, press the OK button. The Keystone
dialog box appears. Use the Point ! ꢀ buttons to correct
keystone distortion. (p.29)
Ceiling
Ceiling
When this function is set to “On,” the picture is top/bottom and
left/right reversed. This function is used to project the image from a
ceiling-mounted projector.
Rear
Rear
When this function is set to “On,” the picture is left/right reversed.
This function is used to project the image from the rear of the
screen.
Reset
This function returns all adjusted values to the factory default
settings. Press the OK button at Reset to display a confirmation
box. To reset, press the OK button at “Yes.”
ꢀNote:
Quit
• The panning function may not operate properly if
the stored Mode in the PC Adjust Menu is used.
(p. 37)
Exit the Screen Size Adjustment Menu.
• The minimum compression ratio can be limited
depending on the input signal or when the
Keystone function is working.
• Digital zoom +/– cannot be selected when Full
screen orTrue is selected.
For zooming in and out the images
Digital zoom +
Select Digital zoom +. The On-Screen Menu disappears and
“D- zoom +” appears. Press the OK button to expand the image
size. Use the Point ! ꢀ buttons to pan the image. The Panning
function can work only when the image is larger than the screen
size.
You can also enter the Digital zoom + mode by pressing the
D-ZOOM button on the remote control unit.
Digital zoom –
Select Digital zoom –. The On-Screen Menu disappears and
“D- zoom –” appears. Press the OK button to compress the image
size.
You can also enter the Digital zoom – mode by pressing the
D-ZOOM button on the remote control unit.
To exit the Digital Zoom +/– mode, press any button except the
D-ZOOM , OK, and Point buttons.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Video Input
Video System Selection
Press the MENU button to display the On-Screen Menu. Use
the Point ꢀ buttons to move the red frame pointer to the
AV System Menu icon.
1
2
Use the Point ! buttons to move the red arrow pointer to
the desired system and then press the OK button.
Video Jack or S-Video Jack
AV SYSTEM MENU (VIDEO OR S-VIDEO)
Auto
The projector automatically detects an incoming video system, and
adjusts itself to optimize its performance.
When Video System is PAL-M or PAL-N, select the system manually.
AV System Menu icon
The selected system is displayed
PAL/SECAM/NTSC/NTSC4.43/PAL-M/PAL-N
Move the pointer to the desired
system and press the OK button.
If the projector cannot reproduce proper video image, select a
specific broadcast signal format from among PAL, SECAM, NTSC,
NTSC 4.43, PAL-M, and PAL-N.
Y, Pb/Cb, Pr/Cr Jacks
AV SYSTEM MENU (COMPONENTVIDEO)
Auto
The projector automatically detects an incoming video signal, and
adjusts itself to optimize its performance.
When the Video System is 1035i or 1080i, select the system
manually.
AV System Menu icon
The selected system is displayed.
Move the pointer to the desired
system and press the OK button.
COMPONENTVIDEO SIGNAL FORMAT
If the projector cannot reproduce proper video image, select a
specific component video signal format from among 480i, 575i,
480p, 575p, 720p, 1035i, and 1080i.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Video Input
Image Level Selection
Menu Operation
Press the MENU button to display the On-Screen Menu. Use
the Point ꢀ buttons to move the red frame pointer to the
Image Select Menu icon.
IMAGE SELECT MENU
1
Use the Point ! buttons to move the red frame pointer to
the desired image level and then press the OK button.
Image Select Menu icon
2
Standard
Move the red frame pointer to the desired
level and press the OK button.
Normal picture level preset on the projector.
Cinema
Picture level adjusted with fine tone.
Custom 1–10
User preset picture adjustment in the Image Adjust Menu. (p. 47)
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Video Input
Screen Size Adjustment
Press the MENU button to display the On-Screen Menu. Use
the Point ꢀ buttons to move the red frame pointer to the
Screen Menu icon.
SCREEN MENU
1
Use the Point ! buttons to move the red frame pointer to
the desired function and then press the OK button.
Screen Menu icon
2
Move the red frame pointer to the desired
function and press the OK button.
Normal
Provide the image at the normal video aspect ratio of 4:3.
ꢀNote:
• Wide cannot be operated when “720p,” “1035i,”
or “1080i” is selected on AV System Menu (p.41).
Wide
Provide the image at the wide screen ratio of 16:9.
Custom
Adjust the screen scale and position manually with this function.
Press the OK button at Custom and the “Custom” is displayed on
the screen for a few seconds. To display the Aspect dialog box,
press the OK button at Custom again and then the Aspect dialog
box appears.
Scale H/V.............. Adjust the Horizontal/Vertical screen scale.
H&V...................... When set to “On,” the aspect ratio is fixed.
The “Scale V” appears dimmed and becomes
unavailable. Adjust “Scale H,” then the screen
scale is automatically modified based on the
aspect ratio.
Position H/V.......... Adjust the Horizontal/Vertical screen position.
Common .............. Save the adjusted scale to all the inputs.
Press the OK button at Common to display a
confirmation box. To save the scale, press the
OK button at “Yes.” When Custom is selected,
the saved scale is used.
Press the OK button at Common or Reset,
to display a confirmation box.
Reset.................... Reset the all adjusted values. Press the OK
button at Reset to display a confirmation box.
To reset, press the OK button at “Yes.”
ꢀNote:
• When no signal is detected, “Normal” is
set automatically and the Aspect dialog box
disappears.
• The adjustable range for Scale H/V and Position
H/V is limited depending on the input signal.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Video Input
Keystone
SCREEN MENU
This function is used to store or reset the keystone correction
when the AC power cord is unplugged. Use the Point ꢀ buttons
to switch between each option.
Store. . . Keep the keystone correction even when the AC power
cord is unplugged.
Reset . . Release the keystone correction when the AC power
cord is unplugged.
Move the red frame pointer to a function and
press the OK button.
To correct keystone distortion, press the OK button. The Keystone
dialog box appears. Use the Point ! ꢀ buttons to correct
keystone distortion. (p.29)
Ceiling
Ceiling
When this function is set to “On,” the picture is top/bottom and
left/right reversed. This function is used to project the image from a
ceiling-mounted projector.
Rear
Rear
When this function is set to “On,” the picture is left/right reversed.
This function is used to project the image from the rear of the
screen.
Reset
This function returns all adjusted values to the factory default
settings. Press the OK button at Reset to display a confirmation
box. To reset, press the OK button at “Yes.”
Quit
Exit the Screen Size Adjustment Menu.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Picture Image
Image Adjustment
Press the MENU button to display the On-Screen Menu. Use
the Point ꢀ buttons to move the red frame pointer to the
Image Adjust Menu icon.
IMAGE ADJUST MENU
1
2
Use the Point ! buttons to move the red frame pointer to
the desired item and then press the OK button to display the
adjustment dialog box. Use the Point ꢀ buttons to adjust
Image Adjust Menu icon
the setting value.
Move the red frame pointer to the desired
item and then press OK button.
Contrast
Press the Point ꢀ button to decrease contrast; press the Point
button to increase the contrast (from 0 to 63).
Brightness
Press the Point ꢀ button to decrease the brightness; press the
Point button to increase the brightness (from 0 to 63).
=
Color
Press the Point ꢀ button to decrease the intensity of the color;
press the Point button to increase the intensity of the color (from
0 to 63).
=
Tint
Press the Point ꢀ buttons to adjust the tint value to obtain
proper color balance (from 0 to 63).
Color Management
Use the Point ꢀ
buttons to adjust the
The Color Management function can be used to adjust the LEVEL,
PHASE, and GAMMA of the selected display colors (except for
black, white, and gray) on the screen and replace these colors with
other colors if required.
setting value.
You can store up to eight (8) color management data.
Use the Point ! buttons to move the red frame pointer
to Color Management, and then press the OK button. The
projected image freezes, and the COLOR MANAGEMENT
POINTER appears.
1
POINTER MODE
Use the Point ! ꢀ buttons to move the pointer to the
spot where you want to adjust the color and then press the
OK button. The COLOR SELECTION window appears, and
the color in the center of the pointer is selected and you can
adjust the color.
2
COLOR MANAGEMENT
POINTER
Use the Point ! ꢀ buttons to adjust the LEVEL and
PHASE of the color, and then press the OK button to confirm
the setting. Then use the Point ! buttons to adjust the
GAMMA for the color and press the OK button to accept
the setting. After adjusting, press the OK button to go to the
COLOR MANAGEMENT LIST.
3
ꢀNote:
=
•
Displayed only in Video Input.
• Tint cannot be selected when the video system
is PAL, SECAM, PAL-M, or PAL-N (p.41).
COLOR SELECTION MODE
LIST
Go to the COLOR MANAGEMENT LIST.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Picture Image
COLOR SELECTION MODE (continued)
COLOR SELECTION MODE
COLOR M.
Level and phase
adjustment palette.
Gamma
adjustment palette.
Return to the COLOR MANAGEMENT POINTER. (If you press
the MENU button on the side control or the remote control
unit, it returns to the COLOR MANAGEMENT POINTER and
you will need to reselect and readjust the color.)
MENU
Return to the IMAGE ADJUST Menu. Any settings that
have been changed will not be stored. To store the changed
settings, be sure to select “LIST” and go to the COLOR
MANAGEMENT LIST.
In the COLOR MANAGEMENT LIST, the adjusted color data
are checkmarked. You can decide whether or not to apply the
adjusted color data in the list to the projected image (see
below).
4
LIST
COLOR M.
MENU
LIST MODE
LIST MODE
Clear the check mark if you do not want to apply the adjusted
color data; select the check mark and then press the OK
button. The check mark disappears.
COLOR PALETTE
DEL
COLOR PALETTE
Return to the COLOR SELECTION mode so that you can
readjust the setting for the color in that line. (This option is
not available if the check mark is cleared.)
DEL
Select the DEL box if you want to delete the adjusted data.
Press the OK button and a confirmation box appears and then
select [Yes]
ALL DEL
Delete all the data in the list. Press the OK button and a
confirmation box appears and then select [Yes].
MENU
The same function as stated above.
ALL DEL
MENU
COLOR M.
COLOR M.
The same function as stated above.
Auto picture control
Use the Point ꢀ buttons to select the desired Auto picture
control position (Off, L1 or L2).
Off . . . . Auto picture control OFF position.
L1 . . . . . Auto picture control LEVEL 1 position.
L2 . . . . . Auto picture control LEVEL 2 position.
Color temp.
Use the Point ꢀ buttons to select the desired Color temp. level
(High, Mid, Low, or XLow).
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Picture Image
White balance (Red/Green/Blue)
Press the Point ꢀ button to lighten red/green/blue tone; press the
Point button to deepen red/green/blue tone (from 0 to 63).
Offset (Red/Green/Blue)
Press the Point ꢀ button to lighten red/green/blue tone of the black
level of an image; press the Point button to deepen red/green/
blue tone of the black level of an image (from 0 to 63).
Press the OK button at this icon to display
other items.
Sharpness
Press the Point ꢀ button to decrease the sharpness of the image;
press the Point button to increase the sharpness of the image
(from 0 to 31).
Gamma
Press the OK button at this icon to
display the previous items.
Use the Point ꢀ buttons to adjust the gamma value to obtain a
better balance of contrast (from 0 to 15).
=
Noise reduction
Noise interference on the screen can be reduced. Press the Point
buttons to change the noise reduction mode.
Press the Point ꢀ
buttons to
adjust the setting value.
ꢀ
Off . . . . Noise reduction mode is “Off”
On . . . . Noise reduction mode is “On”
=
Progressive
An interlaced video signal can be displayed in progressive mode.
Press the Point ꢀ buttons to change the progressive scan mode.
Off . . . . Progressive scan mode is “Off.”
On . . . . Progressive scan mode is “On.”
Film . . . For watching a film. With this function, the projector
reproduces pictures faithful to the original film quality.
Reset
To reset the adjusted data, select Reset and press the OK button. A
confirmation box appears and then select [Yes]. All adjustments will
return to their previous figures.
Store
To store the adjusted data, move the red frame pointer to the Store
icon and press the OK button. The Image Level Menu appears.
Move the red arrow pointer to any of the Custom 1 to 10 in which
you want to set and press the OK button. A confirmation box
appears and then select [Yes].
Image Level Menu
Move the red frame pointer to an
image item to be set and then press
the OK button.
Quit
Exit the Image Adjust Menu.
ꢀNote:
=
•
Displayed only in Video Input.
• When the White balance Red, Green, or Blue is adjusted, the Color
temp. level will change to “Adj.”
• The Film mode in the Progressive function cannot be selected
when the video signal format is 1080i or 1035i.
• Progressive cannot be selected when “480p,” “575p,” or “720p” is
selected (p.41).
Store icon
Press the OK button at this icon
to store the adjustment.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting
Setting
This projector has a Setting menu that allows you to set up other various functions.
Press the MENU button to display the On-Screen Menu. Use
the Point ꢀ buttons to move the red frame pointer to the
Setting Menu icon.
1
SETTING MENU (Language)
Use the Point ! buttons to move the red frame pointer to
2
the desired item and then press the
dialog box appears.
OK button. The Setting
Setting Menu icon
Set the red frame pointer
to the item and press the
OK button.
Language
The language used in the On-Screen Menu is available in English,
German, French, Italian, Spanish, Portuguese, Dutch, Swedish,
Russian, Chinese, Korean, or Japanese.
Menu
This function allows you to adjust the position of the On-Screen
Display and the value adjustment bar in the Picture Image
Adjustment Menu.
Position
Press the OK button at
Language, then the Language
Menu appears.
This function is used to adjust the On-Screen Menu display
position. Press the OK button and the adjustment screen appears
(arrows appear). Use the Point ! ꢀ buttons to adjust the
position. After making the adjustment, press the OK button to
return to the Menu screen.
Simple menu
When this function is set to “On,” the value adjustment bar in the
Picture Image Adjustment Menu appears on the screen.
Display
This function decides whether to display On-Screen Displays.
On . . . . . . . . . . . . Shows all the On-Screen Displays. Use this
function when you want to project images
after the lamp becomes bright enough. The
factory default setting is in this option.
Countdown Off. . . Show the input image instead of the
countdown when turning on the projector.
Use this function when you want to project
the image as early as possible even when the
lamp is not bright enough.
Menu
Off . . . . . . . . . . . . Hide the On-Screen Displays except:
L On-Screen Menu
L “Power off?” (p.24)
L Color management operation screen
(pp.45-46)
L “No signal” for Power management (p.52)
L P-TIMER (p.29)
L ”Please wait....”
L Arrows for theTrue function in the Screen
Menu (p.39)
Set the red frame pointer
to the item and press the
OK button.
Background
The selected background screen will be displayed when no input
signal is detected.
ꢀNote:
Blue . . . Blue colored background.
User . . . The image you captured.
Black. . . Black colored background.
• User cannot be selected when the image is not
captured.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting
Logo
This function allows you to customize the screen logo with Logo
select, Capture, and Logo PIN code lock functions.
Logo
ꢀNote:
• When “On” is selected in the Logo PIN code lock function, Logo
select and Capture functions cannot be selected.
Logo select
This function decides on the starting-up display from among the
following options.
User . . . Show the image you captured.
Default . Show the factory-set logo.
Off . . . . Show the countdown display only.
Capture
Set the red frame
pointer to the item and
press the OK button.
Select [Yes]
to capture
the projected
image.
This function enables you to capture an image being projected to
use it for a starting-up display or interval of presentations.
Select Capture and press the OK button.
A confirmation box appears and select [Yes] to capture the
projected image.
Select [Yes] to stop
capturing.
After capturing the projected image, go to the Logo select
function and set it to “User”. Then the captured image will be
displayed the next time you turn on the projector.
Capture
To cancel the Capture function, select [No].
ꢀNote:
• Before capturing an image, select “Standard” in the Image
Select Menu to capture a proper image (pp. 38, 42). Adjusted
image on the screen cannot be captured.
• A signal from a computer can be captured up to XGA (1024 X
768).
• Certain signals may not be captured properly.
• When capturing the image that has been adjusted by the
Keystone function, the adjusted data is automatically reset and
the projector captures an image without keystone correction.
• When starting to capture a new image, the previously stored
image is cleared even if you cancel the capturing.
• Once you exit the Logo Menu after setting the Logo lock to
"On," you are required to enter the PIN code every attempting to
change the Logo setting.
• User cannot be selected when the image is not captured.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting
Logo PIN code lock
Logo PIN Code Lock
This function prevents an unauthorized person from changing the
screen logo.
Off . . . . The screen logo can be changed freely from the Logo
Menu.
On . . . . The screen logo cannot be changed without a Logo
PIN code.
If you want to change the Logo PIN code lock setting, press the
OK button and the Logo PIN code dialog box appears. Enter a
Logo PIN code by following the steps below. The initial Logo PIN
code is set to “4321” at the factory.
Enter a Logo PIN code
Enter a Logo PIN code
Use the Point ! buttons on the side control or Number buttons
on the remote control unit to enter a number.
When using side control
Use the Point ! buttons on the side control to select a number.
Press the Point button to fix the number and move the red
frame pointer to the next box. The number changes to “3.”
Repeat this step to complete entering a four-digit number. After
entering the four-digit number, move the pointer to “Set.” Press
the OK button so that you can change the Logo PIN code lock
setting.
After a correct Logo PIN code is
entered, the following dialog box
appears.
Change the Logo PIN code lock setting
When using remote control unit
Press the Number buttons on the remote control unit to enter a
number (p.14). When you complete entering a four-digit number,
the pointer moves to “Set.” Press the OK button so that you can
change the Logo PIN code lock setting.
Use the Point ꢀ buttons to switch On/Off,
If you fixed an incorrect number, use the Point ꢀ button to move
the pointer to the number you want to correct, and then enter the
correct number.
Change the Logo PIN code
If you entered an incorrect PIN code, “Logo PIN code” and the
number (3333) will turn red for a moment. Enter the correct PIN
code all over again.
Change the Logo PIN code lock setting
CAUTION:
Use the Point ꢀ buttons to switch On/Off, and then press the
Point button to move the pointer to “Quit.” Press the OK button
to close the dialog box.
WHENYOU HAVE CHANGEDTHE LOGO PIN
CODE,WRITE DOWNTHE NEW PIN CODE
IN COLUMN OFTHE LOGO PIN CODE NO.
MEMO ON PAGE 76, AND KEEP IT SECURELY.
SHOULDTHE LOGO PIN CODE BE LOST OR
FORGOTTEN,THE LOGO PIN CODE SETTING
CAN NO LONGER BE CHANGED.
Change the Logo PIN code
Logo PIN code can be changed to your desired four-digit number.
Press the Point button to select “Logo PIN code change” and
then press the OK button. The New Logo PIN code input dialog
box appears. Set a new Logo PIN code.
NOTE:
Be sure to note the new Logo PIN code and keep it at hand. If you
lost the number, you could no longer change the Logo PIN code
setting. For details on PIN code setting, refer to “PIN code lock”
on pages 53–54.
If you forget your Logo PIN code and unable to change
it, the Logo PIN code can be reset to the factory default
setting (4321) according to the following procedures.
When you reset the Logo PIN code, the PIN code and
Key lock will be reset, as well.
1.Unplug the AC Power Cord from the AC outlet.
2. Hold down the OK button on the projector and
connect the AC Power Cord into the outlet again.
Keep holding down the OK button until the POWER
indicator lights. The Logo PIN code returns to the
factory default setting while the Logo PIN code lock
state will remain the same as the previous set state.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting
Lamp mode
This function allows you to change the brightness of the screen.
Auto mode . . . . . . Brightness according to the input signal.
Normal mode . . . . Normal brightness.
Eco 1 mode . . . . . Lower brightness and Fan control set to
Normal. Lower brightness reduces the
lamp power consumption and extends the
lamp life.
Eco 2 mode . . . . . Lower brightness and Fan control set to
Max. Lower brightness reduces the lamp
power consumption and extends the lamp
life. It is recommended to use Eco 2 mode
when using the projector continuously
over a long period of time. The fan noise
becomes louder in Ecot 2 mode than in
Eco 1 mode. Select the suitalbe mode for
the used environment.
Filter control
ꢀNote:
You can replace the filter with this function. Press the OK button at
Filter control to display a confirmation box. To replace, press the OK
button at “YES” and the electrically operated filter starts to scroll.
• Filter replacement icon and “Please wait...”
message appear on the screen when the
filter is being scrolled.
• When the filter is replaced, the total
accumulated time of the filter use is
automatically set to 0.
You can also replace the filter by using the remote control unit (p.
29).
Fan control
Choose the running speed of cooling fans from the following
options.
Normal....... Operate in this mode under normal conditions.
Max ........... Use this mode when you want to increase the
cooling effect when operating the projector in high
ambient temperature environment. Fan noise is
lounder than “Normal”.
Remote control
Remote control
The eight different remote control codes (Code 1–Code 8) are
assigned to the projector; the factory-set, initial code (Code 1) and
the other seven codes (Code 2 to Code 8).
The same code should set on both the projector and the remote
control unit. For example, operating the projector in “Code 7”, the
remote control code also must be switched to “Code 7”.
When pressing the OK button at
Remote control unit, the Remote
control code menu appears.
To change the code for the projector
Select a remote control code in this Setting Menu.
To change the code for the remote control unit:
Press and hold the MENU button and a number button (1–8) on
the remote control unit for more than 5 seconds to switch
between the codes (p. 16).
RC sensor
Select a location of the infrared remote receiver of the remote
control unit. See “Remote Control Receivers and Operating Range”
on page 15 for details.
Both......... Activate both the front and back receiver.
Front........ Activate only the front receiver.
Back......... Activate only the back receiver.
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting
USB
The Projector has a USB port for interactive operation between
the projector and computers. Set the mode by following the steps
below.
Wireless Mouse mode
Select “
” when controlling a computer with the remote control
unit of this projector.
Projector mode:
“
” Not used.
Power management
Power management
For reducing power consumption as well as maintaining the lamp
life, the Power management function turns off the projection lamp
when the projector is not used for a certain period.
If the input signal is interrupted and no button is pressed for more
than 30 seconds, the timer display with “No signal” appears. It
starts the countdown until the lamp is turned off. The countdown
time can be set between 1 and 30 minutes.
Time left before the lamp is off
Use the Point ꢀ buttons to set the countdown timer.
Select one of the following options:
Ready . . . . When the lamp has been fully cooled down, the
POWER indicator starts blinking. In this condition,
the projection lamp is turned on if the input signal
is reconnected or any button on the side control or
remote control unit is pressed .
Shutdown. . When the lamp has been fully cooled down, the
power is turned off.
Press the OK button at Power
management and the dialog box
appears. Use the Point ꢀ
buttons to choose one of the three
options.
Press the Point button to select
the timer, and then use the Point ꢀ
buttons to set the timer
Off . . . . . . . Power Management function is off.
ꢀNote:
• Factory default is “Ready: 5 min.”
On start
When this function is set to “On,” the projector will be
automatically turned on just by connecting the AC power cord to
the wall outlet.
ꢀNote:
• Be sure to turn off the projector properly (see “Turning Off the
Projector” on page 24). If the projector is turned off in the incorrect
sequence, the On start function does not work properly.
Pointer
You can emphasize a part of the projected image with this function.
Use the Point ꢀ buttons to select a pattern of the Pointer (Arrow,
Cross, or Dot) (P. 30)
ꢀNote:
• The Point ! ꢀ buttons and OK button are invalid when the
Pointer function is operating.
52
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting
Security
Security
Key lock
This function locks the side control and remote control buttons to
prevent operation by unauthorized persons.
. . . . . Unlocked.
. . . . . Lock the side control buttons.
To unlock, use the remote control unit.
. . . . . Lock the remote control buttons.
To unlock, use the side control.
Set the red frame
pointer to the item
and press the OK
button.
If the side control accidentally becomes locked and you
do not have the remote control unit nearby and unable to
operate the projector, contact the service station.
Key lock
PIN code lock
Select Key lock and
this box appears.
Choose one of the
alternatives with the
Point ! buttons
and select [Yes] to
activate it.
This function prevents the projector from being operated by
unauthorized persons and provides the following setting options
for security.
Off . . . . Unlocked.
On1 . . . Enter the PIN code every time turning on the projector.
On2 . . . Enter the PIN code to operate the projector once the
power cord is disconnected; as long as the AC power
cord is connected, the projector can be operated
without a PIN code.
PIN code lock
Whenever you change the PIN code lock setting or the PIN code
(the four-digit number), you are required to enter the PIN code.
“1234” is set as the initial PIN code at the factory.
If you want to change the PIN code lock setting, press the OK
button and the PIN code dialog box appears. Enter a PIN code by
following the steps on the next page.
When the projector
is locked with a PIN
code, the PIN code
lock symbol appears
on the menu bar.
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting
Enter a PIN code
Enter a PIN code
Use the Point ! buttons on the side control or Number buttons
on the remote control unit to enter a number.
When using side control
Use the Point ! buttons on the side control to select a number.
Press the Point button to fix the number and move the red
frame pointer to the next box. The number changes to “3.”
Repeat this step to complete entering a four-digit number. After
entering the four-digit number, move the pointer to “Set.” Press
the OK button so that you can change the PIN code lock setting.
After a correct Logo PIN code is
entered, the following dialog box
appears.
When using remote control unit
Press the Number buttons on the remote control unit to enter a
number (p.14). When you complete entering a four-digit number,
the pointer moves to “Set.” Press the OK button so that you can
change the PIN code lock setting.
Change the PIN code lock setting
Use the Point ꢀ
buttons to switch
between the options.
If you fixed an incorrect number, use the Point ꢀ button to move
the pointer to the number you want to correct, and then enter the
correct number.
If you entered an incorrect PIN code, “PIN code” and the number
(3333) will turn red for a moment. Enter the correct PIN code all
over again.
Change the PIN code
Change the PIN Code Lock setting
Use the Point ꢀ button to select Off, On1, or On2 and then
move the pointer to “Quit” with the Point button. Press the OK
button to close the dialog box.
Change the PIN Code
NOTE:
The PIN code can be changed to your desired four-digit number.
Press the Point buttons to select “PIN code change” and press
the OK button. The New PIN code input dialog box appears. Set a
new PIN code.
If you forget your PIN code and unable to change
it, the PIN code can be reset to the factory default
setting (1234) according to the following procedures.
When you reset the PIN code, the Logo PIN code and
Key lock will be reset, as well.
1.Unplug the AC Power Cord from the AC outlet.
2. Hold down the OK button on the projector and
connect the AC Power Cord into the outlet again.
Keep holding down the OK button until the POWER
indicator lights. The PIN code returns to the factory
default setting while the PIN code lock state will
remain the same as the previous set state.
CAUTION:
WHENYOU HAVE CHANGEDTHE PIN CODE,WRITE DOWN
A NEW PIN CODE IN COLUMN OFTHE PIN CODE NO. MEMO
ON PAGE 76, AND KEEP IT SECURELY. IFYOU FORGETYOUR
PIN CODE,THE PROJECTOR CAN NO LONGER BE STARTED.
Lamp counter
This function is used to reset the lamp counter.
When the lamp life reaches a recommended lamp replacement
This icon appears on the screen when the end of lamp life is
approaching.
time, the time shown in the dialog box turns red and the Lamp
replacement icon appears on the screen, indicating that the end of
lamp life is approaching.
ꢀNote:
• This icon also appears at turning on and
selecting input source.
When replacing the projection lamp, reset the lamp counter. See
“Resetting the Lamp Counter” on page 60.
ꢀNote:
• The Lamp replacement icon will not appear when the Display
function is set to “Off” (p.48), during “Freeze” (p.28), or “Blank”
(p.29).
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting
Filter counter
Filter counter
This function is used to set a frequency for the filter replacement.
Use the Point ! buttons to move the red frame pointer to
Filter counter and then press the OK button. A dialog box appears
showing the Used time option and the Scrolls remaining option.
Set the red frame pointer
to the item and press the
OK button.
UsedTime . . . . . . Show the total accumulated time of the
filter use, timer setting option and the Reset
options. When the projector reaches a time
set in the timer setting, the Filter replacement
icon (Fig. 1) appears on the screen and the
total accumulated time turns red, indicating
that the filter replacement is necessary. If
the filter is out of scroll and the projector
reaches a time set in the timer setting, Fig.
2 appears on the screen, indicating that the
Use the Point ꢀ buttons
to set the timer. Select from
(Off/ 400H/700H/1000H)
depending on the use
environment.
filter cartridge replacement is necessary.
Scrolls remaining . . Show the scroll counter and the Reset
options. When the filter scroll is counted
Fig.1 Filter replacement icon
Filter replacement icon appears on the screen
at a set time.
down to 1 (Scroll counter on the screen is
showing “0 scroll(s)” , the last scroll icon
(Fig. 3) appears on the screen. When the
filter scroll is counted down to 0, the Filter
cartridge replacement icon (Fig. 4) appears
on the screen and the WARNING FILTER
indicator lights orange, indicating that the
filter cartridge replacement is necessary.
Fig.2
Fig.3 Last scroll icon
To set a timer, press the OK button on Used time option. Move the
red arrow pointer to the timer setting option and use the Point ꢀ
buttons to select from (Off/ 400H/700H/1000H) depending on the
Last scroll icon appears on the screen when
the filter is down to the last scroll.
use environment.
Fig.4 Filter cartridge replacement icon
When replacing the Filter cartridge, reset the Filter counter and the
Scroll counter (p.58).
Filter cartridge replacement icon appears on
the screen when the filter scroll is counted
down to 0 scroll.
ꢀNote:
ꢀNote:
• Do not reset the counter(s) when the filter or the filter cartridge are
not replaced.
• Fig.1, Fig. 2, Fig. 3 and Fig. 4 appear at turning
on and selecting input source.
• Timer setting notifies that the filter needs replacement.To replace
the filter, use the filter control function (p.51).
• Fig.1, Fig. 2, Fig. 3 and Fig. 4 will not appear
when the Display function is set to “Off” (p.48),
during “Freeze” (p.28), or “Blank” (p.29).
Factory default
Test pattern
Set the red frame pointer
to the item and press the
OK button.
Various test pattern are available for use when setting up the
projector.
Select Factory default and this box
appears. Select [Yes], and the next
box appears.
Factory default
This function returns all setting values except for the user logo, PIN
code lock, Logo PIN code lock, lamp counter, and filter counter to
the factory default settings.
Quit
Exit the Setting Menu.
Select [Yes] to
activate it.
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance and Care
Filter Instructions
Filter prevents dust from accumulating on the optical elements inside the projector. Should the filter becomes
clogged with dust particles, it will reduce cooling fans’ effectiveness and may result in internal heat buildup
and adversely affect the life of the projector. This projector has an electrically operated filter which helps you to
replace the filter easily. The projector monitors the condition of the filter at all time and replaces a filter with a
new one automatically when it detects the clogging.
If the projector reaches a time set in the timer setting (p.
55), a Filter replacement icon (Fig.1) appears on the screen
and the WARNING FILTER indicator on the top panel lights
up (p.70). When you see this icon, replace the filter as soon
as possible (pp.29, 51). If the filter is out of scroll and the
projector reaches a time set in the timer setting, Fig. 2
appears on the screen, indicating that the filter cartridge
replacement is necessary.
Fig.1 Filter replacement icon
When the filter scroll is counted down to 1, the Last scroll
icon (Fig.3) appears on the screen, indicating that there is
one scroll left in the filter cartridge (p.55).
Fig.2
If the projector detects that the filter is clogged and no scroll
is left in the filter cartridge, a Filter cartridge replacement
icon (Fig. 4) appears on the screen and the WARNING
Fig.3 Last scroll icon
FILTER indicator on the top panel lights up (p.70). When you
see this icon, replace the filter cartridge (p.57) and reset the
Filter counter (p.58) and the Scroll counter (p.58).
When the filter is being scrolled using the remote control
Fig.4 Filter cartridge replacement icon
unit (p.29) or the Filter control function in the setting
menu (p.51), a Filter replacement icon and “Please wait...”
message (Fig.5) appear on the screen and the WARNING
FILTER indicator blinks slow (approx. 2 seconds ON, 2
seconds OFF) (p.69).
Fig.5 Filter replacement icon and
“Please wait...” message.
The WARNING FILTER indicator blinks fast when the
projector detects an abnormal condition, the filter cartridge
is not installed properly, or the filter scroll is not working
properly (p.70).
ꢀNote:
• Do not use the filter cartridge with other projector.The filter
counter and the scroll counter do not recognize the correct
number of remaining scrolls of the used filter cartridge and
the reset function cannot work properly. It may cause a
breakdown.
• Make sure that the projection lamp is turn off when you
are replacing the filter cartridge. If you replace the filter
cartridge when the projection lamp is turn on, the projector
will be shut down automatically for safety purpose
• When you forget to reset the filter counter, the projector
cannot recognize the correct number of remaining scrolls
and may cause a breakdown.
• Do not forget to reset the filter counter and the scroll
counter in the setting menu after replacing the filter
cartridge. If you forget to reset the filter counter and the
scroll counter, the projector cannot recognize the correct
number of remaining scrolls and may cause a breakdown.
• Fig.1, Fig.2, Fig.3, Fig. 4 and Fig.5 will not appear when the
Display function is set to “Off” (p.48), during “Freeze” (p.28),
or “Blank” (p.29).
• The filter cannot be rewinded.
• The filter can be scrolled 9 times since the filter cartridge
has 10 scrolls.
• The filter cartridge is disposable. Do not clean and reuse the
filter cartridge.
• Do not expose the filter cartridge to water or liquid, or it
may cause a breakdown.
• Replace the filter cartridge after all the scroll is used up. If
you replace the filter cartridge when there are some scrolls
left in the filter cartridge, the filter counter and the scroll
counter do not recognize the correct number of remaining
scrolls and the reset function cannot work properly. It may
cause a breakdown.
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance and Care
Replacing the Filter Cartridge
Turn off the projector, and unplug the AC power cord
from the AC outlet.
1
Filter cover
First, clean up the dust on the projector and around the
air vents.
2
Press S on the filter cover to release the latch and open
the filter cover.
3
Pull out the filter cartridge. When taking out the filter
cartridge, put your finger on the filter cartridge’s tab
and then pull.
4
Latch
Put the new one back into the position and close
the filter cover. Make sure that the filter cartridge is
properly and fully inserted.
5
Connect the AC power cord to the projector and turn
on the projector.
6
Reset the filter counter and the scroll counter (p.58).
7
CAUTION
Make sure the filter cartridge is inserted in the
projector. If the filter cartridge is not inserted, the
projector cannot be turned on.
Do not put anything into the air vents. Doing so
may result in malfunction of the projector.
RECOMMENDATION
We recommend avoiding dusty/smoky environments when
operating the projector. Usage in these environments may
cause a poor image quality.
When using the projector under dusty or smoky conditions,
dust may accumulate on a lens, liquid crystal panels, or optical
elements inside the projector. Such condition may degrade the
quality of the projected image.
Filter cartridge
Tab
When the symptoms above are noticed, contact your authorized
dealer or service station for proper cleaning.
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance and Care
Resetting the Filter Counter
Be sure to reset the Filter counter after replacing the filter
cartridge.
Filter counter
Press the MENU button to display the On-Screen Menu. Use
the Point ꢀ buttons to move the red frame pointer to the
Setting Menu icon.
1
Use the Point ! buttons to move the red frame pointer
to Filter counter and then press the OK button. A dialog
box appears showing the Used time option and the Scrolls
2
Select “Used time” and the
dialogue box below appears.
remaining option. Use the Point ! buttons to select Used
time.
Used time shows the total accumulated time of the filter
use, a timer setting option, and the Reset option. Select
Reset and the “Filter counter Reset?” appears. Select [Yes]
to continue.
3
Select Reset and the “Filter
counter Reset?” appears.
Another confirmation dialog box appears, select [Yes] to
reset the Filter counter.
4
Select [Yes],
then another
confirmation
box appears.
Select [Yes] again to reset
the Filter counter.
Resetting the Scroll Counter
Be sure to reset the Scroll counter after replacing the filter
Scroll counter
cartridge.
Press the MENU button to display the On-Screen Menu. Use
the Point ꢀ buttons to move the red frame pointer to the
Setting Menu icon.
1
Use the Point ! buttons to move the red frame pointer
to Filter counter and then press the OK button. A dialog
box appears showing the Used time option and the Scrolls
2
Select “Scrolls remaining” and
the dialogue box below appears.
remaining option. Use the Point ! buttons to select
Scroll(s) remaining.
Scroll(s) remaining shows the number of the remaining
scrolls and the Reset option. Select Reset and the “Scroll
counter Reset?” appears. Select [Yes] to continue.
3
Select Reset and the “Scroll
counter Reset?” appears.
Another confirmation dialog box appears, select [Yes] to
reset the Scroll counter.
4
Select [Yes],
then another
confirmation
box appears.
Select [Yes] again to reset
the Scroll counter.
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance and Care
Lamp Replacement
When the projection lamp of the projector reaches its end of life, the Lamp replacement icon appears on the
screen and LAMP REPLACE indicator lights orange. Replace the lamp with a new one promptly. The timing
when the LAMP REPLACE indicator should light is depending on the lamp mode.
Filter cover
Lamp cover
Top Panel
Lamp replacement icon
Screw
LAMP REPLACE indicator
ꢀNote:
• The Lamp replacement icon will not appear when
the Display function is set to “Off” (p.48), during
“Freeze” (p.28), or “Blank” (p.29).
Follow these steps to replace the lamp.
Turn off the projector and unplug the AC power cord. Let
the projector cool for at least 45 minutes.
1
Open the filter cover. (p.57)
2
3
Loosen the screw and open the lamp cover. Pull out the
lamp by using the built in handle.
Handle
Lamp
Replace the lamp with a new one. Make sure that the
lamp is properly and fully inserted.
4
Close the lamp cover and secure the screw.
5
6
Close the filter cover.
Connect the AC power cord to the projector and turn on
the projector.
7
Reset the Lamp counter (p.60)
8
ꢀNote:
• Be sure to insert the lamp in the correct direction.
• Do not reset the Lamp counter when the projection lamp is
not replaced.
CAUTION
Allow a projector to cool for at least 45 minutes
before you open the lamp cover. The inside of the
projector can become very hot.
CAUTION
For continued safety, replace with a lamp of the
same type. Do not drop the lamp or touch the
glass bulb!The glass can shatter and may cause
injury.
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance and Care
Resetting the Lamp Counter
Be sure to reset the Lamp counter after the lamp is replaced. When the Lamp counter is reset, the LAMP
REPLACE indicator stops lighting and the Lamp replacement icon disappears.
Lamp counter
Press the MENU button to display the On-Screen Menu. Use
the Point ꢀ buttons to move the red frame pointer to the
Setting Menu icon
1
2
Use the Point ! buttons to move the red frame pointer to
Lamp counter and then press the OK button. A dialog box
appears showing the total accumulated time of the lamp
usage and the reset option. Select Reset and the “Lamp
replacement coutner Reset?” appears. Select [Yes] to
continue.
Select Reset and the “Lamp
replacement counter Reset?”
appears.
Another confirmation dialog box appears and select [Yes] to
reset the Lamp counter.
3
ꢀNote:
• Do not reset the Lamp counter without replacing the lamp. Be sure
to reset the Lamp counter only after replacing the lamp.
Select [Yes], then another
confirmation box appears.
Select [Yes] again
to reset the lamp
counter.
ORDER REPLACEMENT LAMP
Replacement lamp can be ordered through your dealer. When ordering, give the following information to the
dealer.
L Model No. of your projector
L Replacement LampType No.
:
:
LV-7585
LV-LP29
60
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance and Care
LAMP HANDLING PRECAUTIONS
This projector uses a high-pressure lamp which must be handled carefully and properly.
Improper handling may result in accidents, injury, or create a fire hazard.
L Lamp lifetime may differ from lamp to lamp and according to the environment of use. There is no
guarantee of the same lifetime for each lamp. Some lamps may fail or terminate their lifetime in a
shorter period of time than other similar lamps.
L If the projector indicates that the lamp should be replaced, i.e., if the LAMP REPLACE indicator lights
up, replace the lamp with a new one IMMEDIATELY after the projector has cooled down. (Follow
carefully the instructions in the Lamp Replacement section of this manual.) Continuous use of the lamp
with the LAMP REPLACE indicator lighted may increase the risk of lamp explosion.
L Lamp may explode as a result of vibration, shock or degradation as a result of hours of use as its
lifetime draws to an end. Risk of explosion may differ according to the environment or conditions in
which the projector and lamp are being used.
IF A LAMP EXPLODES,THE FOLLOWING SAFETY PRECAUTIONS SHOULD BETAKEN.
If a lamp explodes, disconnect the projector’s AC plug from the AC outlet immediately. Contact an
authorized service station for a checkup of the unit and replacement of the lamp. Additionally, check
carefully to ensure that there are no broken shards or pieces of glass around the projector or coming out
from the cooling air circulation holes. Any broken shards found should be cleaned up carefully. No one
should check the inside of the projector except those who are authorized trained technicians and who
are familiar with projector service. Inappropriate attempts to service the unit by anyone, especially those
who are not appropriately trained to do so, may result in an accident or injury caused by pieces of broken
glass.
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance and Care
Cleaning the Projection Lens
Unplug the AC power cord before cleaning.
Gently wipe the projection lens with a cleaning cloth that
contains a small amount of non-abrasive camera lens
cleaner, or use a lens cleaning paper or commercially
available air blower to clean the lens.
Avoid using an excessive amount of cleaner. Abrasive
cleaners, solvents, or other harsh chemicals might scratch
the surface of the lens.
Cleaning the Projector Cabinet
Unplug the AC power cord before cleaning.
Gently wipe the projector body with a soft dry cleaning
cloth. When the cabinet is heavily soiled, use a small amount
of mild detergent and finish with a soft dry cleaning cloth.
Avoid using an excessive amount of cleaner. Abrasive
cleaners, solvents, or other harsh chemicals might scratch
the surface of the cabinet.
When the projector is not in use, put the projector in
an appropriate carrying case to protect it from dust and
scratches.
62
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance and Care
Warning Indicators
The WARNING indicators show the state of the function which protects the projector. Check the state of the
WARNING indicators and the POWER indicator to take proper maintenance.
The projector is shut down and the WARNING TEMP.
indicator is blinking red.
Top Panel
When the temperature inside the projector reaches a
certain level, the projector will be automatically shut down
to protect the inside of the projector. The LAMP indicator
turns red and the WARNINGTEMP indicator blinks while
the projector is being cooled down. When the projector has
cooled down enough (to its normal operating temperature),
it can be turned on again by pressing the POWER button.
ꢀNote:
• The WARNINGTEMP. indicator continues to blink even after the
temperature inside the projector returns to normal. When the
projector is turned on again, the WARNINGTEMP. indicator stops
blinking.
WARNINGTEMP.
blinking red
Then check the matters below:
– Did you provide appropriate space for the projector to be
ventilated? Check the installing condition to see if the air
vents of the projector are not blocked.
– Has the projector been installed near an Air-Conditioning/
Heating Duct or Vent? Move the installation of the
projector away from the duct or vent.
– Is the filter clean? Replace the filter with a new one.
The projector is shut down; and the LAMP indicator is
lighting and other four indicators are blinking.
Top Panel
When the projector detects an abnormal condition, it will
be automatically shut down to protect the inside of the
projector and the LAMP indicator lights on and other four
indicators blink. In this case, unplug the AC power cord and
plug it, and then turn on the projector once again to verify
operation. If the projector cannot be turned on and these
indicators are still lighting and blinking, unplug the AC power
cord and contact the service station.
CAUTION
DO NOT LEAVETHE PROJECTOR WITHTHE
AC POWER CORD CONNECTED UNDER AN
ABNORMAL CONDITION. IT MAY RESULT IN FIRE
OR ELECTRIC SHOCK.
LAMP indicator lights on
and other four indicators
blink
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Troubleshooting
Before calling your dealer or service center for assistance, check the items below once again.
1. Make sure you have properly connected the projector to peripheral equipment as described on pages 20–21.
2. Check the cable connection. Make sure that all computers, video equipment, and power cords are properly
connected.
3. Make sure that all power is switched on.
4. If the projector still does not produce an image, restart your computer.
5. If an image still does not appear, disconnect the projector from your computer and check your computer
monitor’s display. A problem may be noticed with your graphics controller rather than with the projector.
(When you reconnect the projector, be sure to turn the computer and monitor off before you turn on the
projector. Turn on equipment in the order of the projector and computer.)
6. If a problem still persists, check the following solutions.
Problem:
No power.
TryThese Solutions
L Plug the power cord of the projector into the AC outlet.
L Wait until the POWER indicator stops blinking to turn on the projector again. (See page
23)
L Check the WARNING TEMP. indicator. If the WARNING TEMP. indicator is blinking, the
projector cannot be turned on. (See page 63.)
L Check the projection lamp. (See page 59.)
L Unlock the Key lock function for the projector. (See page 53)
L See if the filter cartridge is inserted. (See page 57)
L Adjust the focus of the projector.
L Make sure the projection screen is at least 4.6’ (1.4 m) away from the projector.
L Check the projection lens to see if it needs cleaning.
Image is out of focus.
NOTE: Moving the projector from a cool to a warm place may result in moisture
condensation on the projection lens. If this happens, leave the projector off and
wait until condensation evaporates.
L Check the Ceiling/Rear function. (See pages 40, 44)
L Check the Ceiling function. (See pages 40, 44.)
L Check the Display function. (See page 48.)
Picture is left/right
reversed.
Picture is top/bottom
reversed.
Some displays are
not seen during
operations.
L Check the connection between your computer or video equipment and the projector.
L It takes about 30 seconds to display an image after turning on the projector.
L See if the selected system is corresponding with your computer or video equipment.
L Make sure the temperature is not out of specified operating temperature (41˚F–104˚F
[5˚C–40˚C]).
No image.
L The end of lamp life is approaching. Replace the lamp with a new one promptly. (See
page 59)
appears on the
screen
L The filter is out of scroll. Replace the filter cartridge with a new one promptly. (See pages
56-57)
appears on the
screen
64
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Problem:
Remote control unit
does not work.
TryThese Solutions
L Check the batteries.
L Check if the ALL-OFF switch on the remote control unit is set to “ON.”
L Check if the RC sensor is set properly. (See page 51)
L Make sure no obstruction is between the projector and the remote control unit.
L Make sure you are not too far from the projector when using the remote control unit.
Maximum operating range is 16.4’ (5 m).
L Make sure that the remote control code conforms to the projector’s code.
(See page 51.)
L Unlock the Key lock function for the remote control unit. (See page 53).
L Wireless remote control unit does not work when the remote control cable is connected
to the projector. (See page 15).
L Check the cable connection between the projector and your computer.
L Check the mouse setting on your computer.
L Turn on the projector before you turn on the computer.
Wireless mouse
function does not
work.
L Contact the service station.
Unable to unlock the
Logo PIN code lock,
Security key lock or
Security PIN code
lock.
L Your operation is invalid. Operate correctly.
appears on the
screen
WARNING:
High voltages are used to operate this projector. Do not attempt to open the cabinet.
If problems still persist after following all operating instructions, contact the dealer where you purchased the projector
or the service center. Specify the model number and explain about the problem. We will advise you how to obtain
service.
65
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Menu Tree
Computer Input/Video Input
(1)
(1)
Input 1
RGB (PC analog)
RGB (Scart)
Go to System
Go to System
Input
RGB (PC digital)
RGB (AV HDCP)
(2)
(3)
(1)
(2)
(3)
(2)
Input 2
Input 3
Video
Go to System
Go to System
Go to System
Go to System
Go to System
Go to System
Y, Pb/Cb,Pr/Cr
RGB
Video
Y, Pb/Cb,Pr/Cr
S-video
Network
Information
Image Adjust
Image Adjust
Contrast
Brightness
Color =
0–63
0–63
0–63
0–63
Color
Input
H-sync freq.
V-sync freq.
Screen
Language
Lamp status
Power management
Security
Information
Tint =
Color
management
Gamma
List
Color M.
Key lock
PIN code lock
AllDel
Menu
Menu
Remote control code
Color M.
Off/L1/L2
Auto picture
control
Color temp.
High
Mid
Low
XLow
Adj.
Red
Green
Blue
0–63
0–63
0–63
Offset
Red/Green/Blue
Sharpness
Gamma
0–31
0–15
Noise reduction = Off/On
Progressive =
Off/On/Film
Reset
Store
Yes / No
Custom 1
Custom 10
Quit
Quit
=
Displayed only in Video Input
ꢀNote:
• The Menu display varies depending on the input signal.
66
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Computer Input
(1)
Mode 1
Mode 2
SVGA 1
SVGA 2
SVGA 3
Standard
System
Image Select
High contrast
Custom 1
Custom 10
= System displayed in the System Menu varies depending on the input signal.
Auto PC adj.
Normal
PC Adjust
Screen
Fine sync.
Total dots
Position H
Position V
Current mode
Clamp
0–31
True
Wide
Full screen
Digital zoom +
Digital zoom -
Custom
Scale
H & V
Position
Common
Reset
H / V
On/Off
H / V
Display area - H
Display area - V
Reset
Yes/No
Mode free
Store
Keystone
Store
Mode 1
Reset
On/Off
On/Off
Ceiling
Rear
Mode 10
Quit
Reset
Quit
Quit
Video Input
(2)
(3)
Auto
Auto
System
System
PAL
1080i
1035i
720p
575p
480p
575i
SECAM
NTSC
NTSC 4.43
PAL-M
PAL-N
480i
Standard
Cinema
Normal
Wide
Image Select
Screen
Custom 1
Scale
H / V
Custom
H & V
On/Off
Position
Common
Reset
H / V
Custom 10
Keystone
Store
Reset
On/Off
On/Off
Ceiling
Rear
Reset
Quit
ꢀNote:
• The Menu display varies depending on the input signal.
67
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Computer Input/Video Input
Language
12 languages provided.
Quit
Setting
Menu
Position/Simple Menu
On/Countdown Off/Off
Blue/User/Black
Display
Background
Logo
User/Default/Off
Logo select
Capture
Yes/No
Logo PIN code lock
On/Off
Logo PIN code change
Quit
Quit
Lamp mode
Filter control
Fan control
Auto mode/Normal mode /Eco 1 mode/Eco 2 mode
Yes/No
Normal/Max
Code 1
Remote Control
Code 8
Quit
RC sensor
USB
Both/Front/Back
Mouse
Projector
Off
Power management
Ready
Shut down
1–30 Min.
Quit
On start
Pointer
On/Off
Arrow/Cross/Dot
Security
Key lock
Off
Projector
Remote Control
PIN code lock
Quit
Off/On1/On2
PIN code change
Lamp counter
Filter counter
Hour(s)
Reset
Yes/No
Quit
Used time
Off/400H/700H/1000H
Yes/No
Reset
Quit
Scrolls remaining
Scroll(s)
Yes/No
Reset
Quit
Test pattern
8 test patterns provided
Quit
Factory default
Quit
Yes/No
68
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Indicators and Projector Condition
Check the indicators for the projector condition.
The projector is operating normally.
Indicators
WARNING WARNING
LAMP
REPLACE
orange
Projector Condition
POWER
green
LAMP
TEMP.
FILTER
red
red
orange
The projector is off. (The AC power cord is unplugged.)
=
=
=
V
V
V
The projector is in stand-by mode. Press the POWER button
to turn on the projector.
The projector is operating normally.
The projector is preparing for stand-by or the projection lamp
is being cooled down. The projector cannot be turned on until
cooling is completed and the POWER indicator lights green.
=
=
V
The projector is in the Power management mode.
V
V
The filter is scrolled using the FILTER button on the remote
control unit or the Filter control function in the setting menu.
When the filter is being scrolled, the Filter replacement icon
and “Please wait...” message (Fig. 1) appear on the screen for
10 seconds.
Fig.1 Filter replacement icon and “Please wait...”
The projector is detecting abnormal condition.
Indicators
WARNING WARNING
LAMP
REPLACE
orange
Projector Condition
POWER
green
LAMP
TEMP.
FILTER
red
red
orange
The temperature inside the projector is elevated close to the
abnormally high level.
V
V
=
=
The temperature inside the projector is abnormally high. The
projector cannot be turned on. When the projector is cooled
down enough and the temperature returns to normal, the
POWER indicator lights green and the projector can be turned
on. (The WARNINGTEMP. indicator keeps blinking.) Check and
replace the filter.
• • • blinking slow
• • • on
• • • dim
• • • off
• • • blinking at the normal rate
(approx. 1 second ON,
1 second OFF)
(approx. 2 seconds ON,
2 seconds OFF)
• • •blinking fast
(approx. 0.5 seconds ON,
0.5 seconds OFF)
69
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Indicators
WARNING WARNING
LAMP
REPLACE
orange
Projector Condition
POWER
green
LAMP
TEMP.
FILTER
red
red
orange
The projector has been cooled down enough and the
temperature returns to normal. When turning on the projector,
the WARNINGTEMP. indicator stops blinking. Check and
replace the filter.
V
=
The lamp cannot light up. (The projector is preparing for stand-
by or the projection lamp is being cooled down. The projector
cannot be turned on until cooling is completed.)
=
=
=
The lamp cannot light up. (The lamp has been cooled down
enough and the projector is in stand-by mode and ready to be
turned on with the POWER button.)
The lamp has been used overtime. Replace the lamp
immediately and then reset the lamp counter. The indicator
will be turned off after resetting the counter.
If the Filter counter reached a time set in the timer setting,
a Filter replacement icon (Fig.2) appears on the screen and
the WARNING FILTER indicator on the top panel lights up.
Replace the filter as soon as possible. If the filter is out of
scroll and the projector reaches a time set in the timer setting,
Fig. 3 appears on the screen and the WARNING FILTER
indicator lights up. Replace the filter cartridge as soon as
possible.
V
Fig.2 Filter replacement icon
If the filter is clogged and no scroll is left in the filter cartridge,
a Filter cartridge replacement icon (Fig.4) appears on the
screen and the WARNING FILTER indicator lights up. Replace
the filter cartridge as soon as possible.
Fig.3
ꢀNote:
• Fig.2, Fig.3 and Fig.4 icon will not appear when the Display function
is set to “Off” (p.48), during “Freeze” (p.28), or “Blank” (p.29).
Fig.4 Filter cartridge replacement icon
The filter cartridge is not installed in the projector. Check the
filter compartment to see if the filter cartridge is installed in
the projector. When the filter cartridge is installed and the
indicators continue to light and blink, read the column below.
The projector detects an abnormal condition and cannot be
turned on. Unplug the AC power cord and plug it again to turn
on the projector. If the projector is turned off again, unplug the
AC power cord and contact the dealer or the service center.
Do not leave the projector on. It may cause an electric shock
or a fire hazard.
=
When the filter detects clogging, reaches a time set in the timer setting or runs out of the filter scroll, the WARNING
FILTER indicator lights orange. When this indicator lights orange, replace the filter or the filter cartridge with a new one
promptly. Reset the Filter counter and Scroll counter after replacing the filter cartridge (p.58).
When the projection lamp reaches its end of life, the LAMP REPLACE indicator lights orange. When this indicator lights
orange, replace the projection lamp with a new one promptly. Reset the lamp counter after replacing the lamp (p.59).
V
70
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Compatible Computer Specifications
Basically this projector can accept the signal from all computers with the V- and H-Frequency mentioned below
and less than 180 MHz of Dot Clock.
PC Adjustment is limited when selecting these modes.
ON-SCREEN
DISPLAY
H-Freq.
(kHz)
V-Freq.(Hz)
ON-SCREEN
DISPLAY
H-Freq.
(kHz)
V-Freq.(Hz)
RESOLUTION
RESOLUTION
VGA 1
VGA 2
VGA 3
VGA 4
VGA 5
VGA 6
VGA 7
MAC LC13
MAC 13
480p
640x480
720x400
640x400
640x480
640x480
640x480
640x480
640x480
640x480
640x480
768x575
31.470
31.470
31.470
37.860
37.860
37.500
43.269
34.970
35.000
31.470
31.250
15.625
59.880
70.090
70.090
74.380
72.810
75.000
85.000
66.600
66.670
59.880
50.000
50.000
SXGA 4
SXGA 5
SXGA 6
SXGA 7
SXGA 8
SXGA 9
SXGA 10
SXGA 11
SXGA 12
SXGA 13
1400x1050
1400x1050
1280x1024
1280x1024
1280x1024
1280x1024
1280x960
1152x900
1152x900
64.030
62.500
71.690
81.130
63.980
79.976
60.000
61.200
71.400
50.000
60.010
58.600
67.190
76.107
60.020
75.025
60.000
65.200
75.600
86.000
1280x1024
(Interlace)
1280x1024
(Interlace)
575p
575i
SXGA 14
50.000
94.000
768x576
(Interlace)
640x480
(Interlace)
SXGA 15
SXGA 16
SXGA 17
SXGA 18
SXGA 19
SXGA 20
SXGA+ 1
SXGA+ 2
SXGA+ 3
SXGA+ 4
SXGA+ 5
MAC 21
MAC
1280x1024
1280x1024
1152x900
63.370
76.970
61.850
46.430
63.790
91.146
63.970
65.350
65.120
64.030
62.500
68.680
75.000
80.000
48.360
47.700
48.360
56.160
47.776
60.289
68.633
49.600
41.200
75.000
81.250
87.500
93.750
45.000
37.500
33.750
60.010
72.000
66.000
86.700
60.180
85.024
60.190
60.120
59.900
60.010
58.600
75.060
75.080
75.080
60.000
60.000
60.000
72.000
59.870
74.893
84.837
60.050
50.000
60.000
65.000
70.000
75.000
60.000
50.000
60.000
480i
15.734
60.000
SVGA 1
SVGA 2
SVGA 3
SVGA 4
SVGA 5
SVGA 6
SVGA 7
SVGA 8
SVGA 9
SVGA 10
SVGA 11
MAC 16
XGA 1
XGA 2
XGA 3
XGA 4
XGA 5
XGA 6
XGA 7
XGA 8
XGA 9
800x600
800x600
800x600
800x600
800x600
800x600
800x600
800x600
800x600
800x600
800x600
832x624
1024x768
1024x768
1024x768
1024x768
1024x768
1024x768
1024x768
1024x768
35.156
37.880
46.875
53.674
48.080
37.900
34.500
38.000
38.600
32.700
38.000
49.720
48.360
68.677
60.023
56.476
60.310
48.500
44.000
63.480
36.000
56.250
60.320
75.000
85.060
72.190
61.030
55.380
60.510
60.310
51.090
60.510
74.550
60.000
84.997
75.030
70.070
74.920
60.020
54.580
79.350
87.170
1280x1024
(Interlace)
1280x1024
1280x1024
1400x1050
1400x1050
1400x1050
1400x1050
1400x1050
1152x870
1280x960
1280x1024
1366x768
1360x768
1376x768
1360x768
1280x768
1280x768
1280x768
1280x800
1280x800
1600x1200
1600x1200
1600x1200
1600x1200
1280x720
1280x720
=
MAC
WXGA 1
WXGA 2
WXGA 3
WXGA 4
WXGA 6
WXGA 7
WXGA 8
WXGA 9
WXGA 10
UXGA 1
UXGA 2
UXGA 3
UXGA 4
720p
1024x768
(Interlace)
=
XGA 10
XGA 11
XGA 12
1024x768
1024x768
1024x768
(Interlace)
62.040
61.000
35.522
77.070
75.700
86.960
=
=
=
XGA 13
XGA 14
XGA 15
MAC 19
SXGA 1
SXGA 2
SXGA 3
1024x768
1024x768
1024x768
1024x768
1152x864
1280x1024
1280x1024
46.900
47.000
58.030
60.240
64.200
62.500
63.900
58.200
58.300
72.000
75.080
70.400
58.600
60.000
720p
1035i
1920x1035
(Interlace)
1920x1080
(Interlace)
1920x1080
(Interlace)
1080i
33.750
28.125
60.000
50.000
=
True cannot be selected when UXGA1, UXGA2, UXGA3, and UXGA4 are selected (p.39)
71
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
When an input signal is digital from the DVI terminal, refer to the chart below.
ON-SCREEN
DISPLAY
H-Freq.
(kHz)
V-Freq.(Hz)
ON-SCREEN
DISPLAY
H-Freq.
(kHz)
V-Freq.(Hz)
RESOLUTION
RESOLUTION
D-VGA
D-480p
D-575p
D-SVGA
640x480
720x480
720x575
800x600
1024x768
1366x768
1360x768
1376x768
1360x768
1366x768
1280x768
1280x768
31.470
31.470
31.250
37.879
43.363
48.360
47.700
48.360
56.160
46.500
47.776
60.289
59.940
59.880
50.000
60.320
60.000
60.000
60.000
60.000
72.000
50.000
59.870
74.893
D-WXGA 9
D-WXGA 10
D-720p
D-720p
D-1035i
1280x800
1280x800
1280x720
1280x720
49.600
41.200
45.000
37.500
33.750
60.050
50.000
60.000
50.000
60.000
1920x1035
(Interlace)
D-XGA
1920x1080
(Interlace)
1920x1080
(Interlace)
D-WXGA 1
D-WXGA 2
D-WXGA 3
D-WXGA 4
D-WXGA 5
D-WXGA 6
D-WXGA 7
D-1080i
33.750
28.125
60.000
50.000
D-1080psf/30
D-1080psf/25
D-1080psf/24
1920x1080
1920x1080
1920x1080
33.750
28.125
27.000
60.000
50.000
48.000
ꢀNote:
• When the input signal is D-SXGA 1, D-SXGA 2, and D-SXGA 3, images may not be displayed properly depending
on computers.
• Depending on the condition of signals and the type and length of cables, these signals may not be properly
viewed.
• Specifications are subject to change without notice.
72
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Technical Specifications
Mechanical Information
ProjectorType
Multi-media Projector
Dimensions (W x H x D)
Net Weight
14.57” x 7.36” x 19.37” (370 mm x 187 mm x 492 mm) (Not including raised portions)
28.7 lbs (13.0 kg)
0˚ to 6.5˚
Feet Adjustment
Panel Resolution
LCD Panel System
Panel Resolution
1.3”TFT Active Matrix type, 3 panels
1,024 x 768 dots
Number of Pixels
2,359,296 (1,024 x 768 x 3 panels)
Signal Compatibility
Color System
PAL, SECAM, NTSC, NTSC4.43, PAL-M, and PAL-N
480i, 480p, 575i, 575p, 720p, 1035i, and 1080i
H-sync. 15 kHz–100 kHz, V-sync. 48 Hz–100 Hz
High DefinitionTV Signal
Scanning Frequency
Optical Information
Projection Image Size (Diagonal)
Throw Distance
Adjustable from 31” to 400”
4.6’ - 48.2’ (1.4 m - 14.7 m)
Projection Lens
F= 1.7 to 2.0, f= 48.2 to 62.6 mm with motor zoom and focus
330 W NSHA lamp
Projection Lamp
Interface
Input 1
Digital (DVI-D) x 1, Analog (Mini D-sub 15 pin) x 1
Analog RGB (Mini D-sub 15 pin)Terminal x 1
BNCType x 5 (G or Video/Y, B or Cb-Pb, R or Cr-Pr, HV and V)
RCAType x 3 (Video/Component), Mini DIN 4 pin x 1 (S-video)
Mini jack (stereo) (Wired Remote) x 1
D-sub 9 pin x 1
Monitor Out
Input 2
Input 3
R/C Jack
Control Port
USB Connector
Option
USB Series B x 1
Network ImagerTerminal x 1
Power
Voltage and Power Consumption
AC 100–120 V (4.6A Max. Ampere), 50/60 Hz (The U.S.A and Canada)
AC 200–240 V (2.3A Max. Ampere), 50/60 Hz (Continental Europe andThe U.K.)
490W (17.6W in stand-by mode)
Operating Environment
OperatingTemperature
StorageTemperature
41˚F–104˚F (5˚C–40˚C)
14˚F–140˚F (-10˚C–60˚C)
Remote Control Unit
Battery
AAA or LR03Type x 2
Operating Range
Dimensions
16.4’ (5 m/ 30˚)
1.8” (W) x 1.0” (H) x 5.7” (D) (45 mm x 25 mm x 145 mm)
3.5 oz (99 g) (including batteries)
Net Weight
Accessories
User’s Manual (CD-ROM)
Quick Start Guide
AC Power Cord
Light-block sheet (For option lens)
Spacer (For option lens)
Logo Plate
Remote Control Unit and Batteries
VGA Cable
L The specifications are subject to change without notice.
L LCD panels are manufactured to the highest possible standards. Even though
99.99% of the pixels are effective, a tiny fraction of the pixels (0.01% or less)
may be ineffective by the characteristics of the LCD panels.
USB Cable
PIN Code Label
73
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Optional Parts
The parts listed below are optionally available. When ordering those parts, specify the item name and Model No.
to the sales dealer.
Model No.
Ultra Wide Angle Lens
Wide Angle Zoom Lens
Long Focus Zoom Lens
Ultra Long Focus Zoom Lens
Ceiling Attachment
High Ceiling Attachment
DVI Cable
Type No. : LV-IL01
Type No. : LV-IL02
Type No. : LV-IL03
Type No. : LV-IL04
Type No. : LV-CL13
Type No. : LV-CL14
Type No. : LV-CA29
Type No. : LV-CA31
Type No. : LV-NI02
Scart-VGA Cable
Network Imager
Lens Replacement
The lens of this projector can be replaced with other optional lens. This feature enables you to use the projector
for wide variety of uses.
For installation and replacement of the lens, always contact the sales dealer. The projector lens must be
installed or replaced by well-trained sales or service engineers. Do not attempt to install and replace the lens by
yourself as it may cause injury.
Do not hold the lens when carrying or lifting the projector. It may cause serious damage to the projector.
To the sales and service engineers:
For the lens replacement and lens installation, refer to the installation manual of the optional lens. Before replacing and
installing the lens, make sure that you are using the lens with the correctType No.
PJ Link Notice
This projector is compliant with PJLink Standard Class 1 of JBMIA (Japan Business Machine and Information
System Industries Association). The projector supports all commands defined by PJLink Class 1 and is verified
conformance with PJLink Standard Class 1.
Projector Input
Input 1
PJLink Input
RGB 1
RGB 2
Parameter
RGB (PC analog)
RGB (Scart)
RGB (PC digital)
RGB (AV HDCP)
Video
Y, Pb/Cb,Pr/Cr
RGB
Video
11
12
31
32
21
22
13
23
24
25
51
DIGITAL 1
DIGITAL 2
VIDEO 1
VIDEO 2
RGB 3
VIDEO 3
VIDEO 4
VIDEO 5
NETWORK 1
Input 2
Input 3
Input 4
Y, Pb/Cb,Pr/Cr
S-video
Network
PJLink is a registered trademark of JBMIA and pending trademark in some countries.
74
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Configurations of Terminals
ANALOG/ MONITOR OUT (Mini D-sub 15 pin)
Red Input
Green Input
Blue Input
+5V Power
Ground (Vert. sync.)
Sense 0
DDC Data
Horiz. sync.
Vert. sync.
1
2
3
4
5
6
7
8
9
2
5
1
4
3
10
11
12
13
14
15
10
9
8
7
6
15
12
11
14
13
Sense 2
Ground (Horiz.sync.)
Ground (Red)
Ground (Green)
Ground (Blue)
DDC Clock
DIGITAL DVI-D (DVI 24 PIN)
T.M.D.S. Data2–
T.M.D.S. Data2+
T.M.D.S. Data2 Shield
No Connect
No Connect
DDC Clock
T.M.D.S. Data1–
T.M.D.S. Data1+
T.M.D.S. Data1 Shield
No Connect
No Connect
+5V Power
T.M.D.S. Data0–
T.M.D.S. Data0+
T.M.D.S. Data0 Shield
No Connect
1
2
3
4
5
6
7
8
9
17
18
19
20
21
22
23
24
10
11
12
13
14
15
16
1
9
2
3
4
5
6
7
8
10 11 12 13 14 15 16
17 18 19 20 21 22 23 24
No Connect
T.M.D.S. Clock Shield
T.M.D.S. Clock+
T.M.D.S. Clock–
DDC Data
No Connect
Ground (for +5V)
Hot Plug Detect
USB CONNECTOR (Series B)
1
2
3
4
Vcc
- Data
+ Data
Ground
2
3
1
4
CONTROL PORT CONNECTOR (D-sub 9 pin)
Serial
1
2
3
4
5
6
7
8
9
-----
R X D
T X D
-----
SG
-----
RTS
CTS
-----
75
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
While the projector is locked with the PIN code...
Put the label below (supplied) on in a prominent place of
the projector’s body while it is locked with a PIN code.
The logo is upside down when hanging the projector from the ceiling...
When hanging the projector from the ceiling, the logo looks
upside down. To display the logo in correct direction, put the
logo plate (supplied) on the reversed logo.
76
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Dimensions
14.57 (370)
Unit: inch (mm)
4.33 (110) 4.33 (110)
6.5º MAX
5.75 (146)
5.20 (132) 4.13 (105)
Screw Holes for Ceiling Mount
Screw: M6
Depth: 0.393 (10.0)
77
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Serial Control Interface
This projector provides a function to control and monitor the projector's operations by using the RS-232C serial
port.
Operation
Connect a RS-232C serial cross cable to CONTROL
PORT on the projector and serial port on the PC.
(See p.20)
1
Launch a communication software provided with PC
and setup the communication condition as follows:
2
Baud rate
Parity check
Stop bit
Flow control
Data bit
: 9600 / 19200 bps
: none
: 1
: none
: 8
ꢀNote:
• The default of the baud rate is set to 19200 bps. If an
error occurs in the communication, change the serial
port and the communication speed (baud rate).
Type the command for controlling the projector and
then enter the "Enter" key.
3
Example
When you want to change the input to INPUT 2, Type
'C' '0' '6' 'Enter'.
ꢀNote:
• Enter with ASCII 64-byte capital characters and one-
byte characters.
78
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Functional Execution Command
Format
The command is sent from PC to the projector with
the format below;
'C' [Command] 'CR'
Command: two charactors (refer to the
command table below.
-The projector decodes the command and returns the
'ACK' with the format below;
'ACK' 'CR'
-When the projector can not decode the command, it
returns with format below.
‘?’ ‘CR’
Command
C00
Function
Turn the projector ON
Command
C3A
C3B
C3C
C3D
C3F
C46
C47
C4A
C4B
C50
C51
C52
C53
C5D
C5E
C5F
C60
C89
C8E
C8F
C90
C91
Function
Pointer RIGHT
Pointer LEFT
Pointer UP
Pointer DOWN
Enter
Zoom DOWN
Zoom UP
Focus DOWN
Focus UP
Select Input 1 Analog RGB
Select Input 1 SCART
Select Input 1 DVI (PC Digital)
Select Input 1 DVI (AV HDCP)
Lens shift UP
Lens shift DOWN
Lens shift LEFT
Lens shift RIGHT
Auto PC Adj.
Turn the projector OFF
(immediately OFF)
C01
C02
C05
C06
C07
C08
C0D
C0E
C0F
C10
C1C
C1D
C20
C21
C23
C24
C25
C28
C29
C33
C34
C35
Turn the projector OFF
Select Input 1
Select Input 2
Select Input 3
Select Network
Video mute ON
Video mute OFF
Aspect 4:3
Aspect 16:9
Menu ON
Menu OFF
Brightness UP
Brightness DOWN
Select Input 2 Video
Select Input 2Y, Pb/Cb,Pr/Cr
Select Input 2 RGB
ON Start ON
Keystone UP
Keystone DOWN
Keystone RIGHT
Keystone LEFT
ON Start OFF
Select Input 3 Video
Select Input 3 S-video
Select Input 3Y, Pb/Cb,Pr/Cr
79
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Status Read Command
Format
The command is sent from PC to the projector with
the format below;
'CR' [Command] 'CR'
Command: one character (refer to the command
table below.
The projector decodes the command and returns the
'Charactor string' with the format below;
Projector
Return
Command
Function
Projectro status
Power On
00
80
40
20
10
28
24
04
Stand-by mode
Countdown
Cooling down
Power Malfunction
Cooling down at the temperature abnormally
Cooling down at Power Management mode
Power Management mode after Cooling down
CR0
Status Read
Cooling down after the projector is turned off when the lamps
are out.
Stand-by mode after Cooling down when the lamps are out.
21
81
88
Stand-by mode after Cooling down at the temperature
abnormally.
S1 =Temperature at Sensor 1 (˚C)
S2 =Temperature at Sensor 2 (˚C)
S3 =Temperature at Sensor 3 (˚C)
(ex.) S1 = 12.3˚C, S2 = 23.4˚C, S3 = 34.5˚C
-->The projector displays “12.3 23.4 34.5”
CR6
Temperature Read
S1 S2 S3
(For each sensor, two digit and the tenth place numbers are
displayed with a space between each temperature.)
Communication failure
?
The tables on page 79 and 80 show the typical command lists for controlling the projector. Please consult your
local dealer for further information of other commands.
80
Download from Www.Somanuals.com. All Manuals Search And Download.
CANON INC.
30-2, Shimomaruko 3-chome, Ohta-ku,
Tokyo 146-8501, Japan
CANON (Schweiz) A.G.
Industriestrasse 12, 8305 Dietlikon,
Switzerland
CANON U.S.A., INC.
One Canon Plaza, Lake Success, NY 11042,
U.S.A.
CANON BELGIUM N.V./S.A
Bessenveldstraat 7, 1831 Diegem, Belgium
CANON GmbH
Zetschegasse 11,A-1230 Wien,Austria
CANON CANADA, INC.
6390 Dixie Road Mississauga, Ontario L5T
1P7 Canada
CANON ESPANA S.A.
C/Joaquin Costa 41, 28002 Madrid, Spain
CANON LATIN AMERICA, INC.
703 Waterford Way Suite 400 Miami, Florida
33126 U.S.A.
CANON SVENSKA AB
Gustav III:s, Boulevard 26, 169 88 Solna, Sweden
CANON NORGE A/S
Hallagerbakken 110, P.O. Box 33, Holmlia,
N-1201 Oslo, Norway
CANON MEXICANA, S. de R.L. de C.V.
Boulevard Manuel Avila Camacho, No. 138
PB, Pisos 15, 16 y 17Col. Lomas de
CANON OY
Huopalahdentie 24, P.O. Box 1, FIN-00351
Helsinki, Finland
Chapultepec, CP 11000, Mexico D.F., Mexico
CANON EUROPA N.V.
P.O.Box 2262, 1180 EG Amstelveen,The
Netherlands
CANON HONGKONG CO., LTD.
19/F.,The MetropolisTower, 10 Metropolis
Drive, Hunghom, Kln., H.K.
CANON COMMUNICATION & IMAGE
FRANCE S.A.
12 Rue De L’Industrie, 92414 Corbevoie, Cedex, France
CANON SINGAPORE PTE. LTD.
1 HarbourFront Avenue #04-01, Keppel Bay
Tower Singapore 098632
CANON (UK) LTD.
Woodhatch, Reigate, Surrey RH2 8BF,
United Kingdom
CANON AUSTRALIA PTY. LTD.
1Thomas Holt Drive, North Ryde, Sydney,
N.S.W.2113,Australia
CANON DEUTSCHLAND GmbH
Europark Fichtenhain A 10, 47807 Krefeld,
Germany
CANON NEW ZEALAND LTD.
Akoranga Business Park,Akoranga Drive,
Northcote,Auckland, New Zealand
CANON ITALIA S.p.A.
Via Milano, 8 San Donato M. se-20097 (MI), Italy
CANON DANMARK A/S
Knud Hoejgaards Vej 1, DK-2860 Soeborg, Denmark
© CANON INC. 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Black Decker Lawn Mower CM1640 User Manual
BridgeWave Switch AR80 User Manual
Brinkmann Landscape Lighting Solar Powered LED Garden Accent Light User Manual
Canon Camera Lens 16 35mm f 40L IS USM User Manual
Canon Server A1200 User Manual
Casio Tablet IT 300 User Manual
Casio Watch 2456 User Manual
Changhong Electric Flat Panel Television LT1512E, LT1712E, LT2012E, LT2612E, LT3212E User Manual
Chauvet Landscape Lighting 230SR User Manual
Cisco Systems Cordless Telephone 7942G User Manual