Canon Printer 6219B002 User Manual

PIXMA iP7200 series  
Setup Guide  
© CANON INC. 2012  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Network Connection  
Wireless Connection  
a Preparation for Connection  
Before Starting Wireless Connection Setup  
1. Make sure that the printer is turned on.  
If the power is on, the POWER lamp (A) will be lit.  
Notes on Wireless Connection  
Make sure that the computer is connected to the access point (A) (or wireless network router) you want to connect your  
printer to.  
The configuration, router functions, setup procedures and security settings of the network device vary depending on your  
system environment. For details, refer to the manual of your network device or contact its manufacturer.  
Check if your device supports IEEE802.11n, 802.11g or 802.11b.  
If your device is set to the "IEEE802.11 n only" mode, WEP or TKIP cannot be used as a security protocol. Change the  
security protocol for your device to something other than WEP and TKIP or change the setting to something other than  
"IEEE802.11 n only."  
For office use, consult your network administrator.  
Take added care when connecting to a network that is not protected with security measures, as there is a risk of disclosing  
data such as your personal information to a third party.  
An "Ad-hoc connection," which establishes a direct connection to the computer over a wireless connection without an  
access point, is not supported. Be sure to prepare an access point.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
b Connection Using WPS  
1. Press and hold the Wi-Fi button (A) on the printer when you are ready to press the button on the  
access point.  
2. Make sure that the (blue) Wi-Fi lamp flashes quickly and the POWER lamp is lit as shown in the  
illustration above, then press and hold the button on the access point within 2 minutes.  
3. Make sure that the (blue) Wi-Fi lamp and POWER lamp are lit.  
The network connection setup is now complete.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Troubleshooting  
WPS  
When the (blue) Wi-Fi lamp flashes slowly and the (orange) Alarm lamp is lit:  
• Press the button on only one access point.  
• Check the security settings of the access point.  
After checking the above points, wait for a while and configure wireless connection setting again.  
For details on how to check the security settings of the access point, refer to the manual supplied with the access  
point or contact its manufacturer.  
When the (blue) Wi-Fi lamp flashes quickly and the (orange) Alarm lamp is lit:  
• Is the network device (router, etc.) turned on? If the network device is already turned on, turn it off, then turn it back  
on.  
Are the computer and network device configured?  
• Are the access point and printer installed in an open space where wireless communications are possible?  
• Is the access point operating in IEEE802.11n (2.4 GHz), IEEE802.11g or IEEE802.11b?  
Wait for a while, then bring the access point and printer close to each other, and configure wireless connection  
settings again within a specified time.  
For details on how to check the settings of the access point, refer to the manual supplied with the access point or  
contact its manufacturer.  
To configure wireless connection settings again  
To configure wireless connection settings again, press the RESUME/CANCEL button (A).  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Black Decker Saw 587384 00 User Manual
Blanco Indoor Furnishings 157 066 User Manual
Bradford White Corp Water Heater IGI 180R User Manual
Briggs Stratton Portable Generator 30358 User Manual
Brother Sewing Machine XC8324021 User Manual
Cambridge SoundWorks Speaker System THX 250D User Manual
Casio Musical Toy Instrument CTK 2080 User Manual
CDA Cooktop HCG601 User Manual
Celestron Telescope 4SE User Manual
Chromalox Electric Heater SRCCH 1 User Manual