SB_PC1270D_FG_EN.book Page i Monday, February 18, 2002 12:20 PM
Canon
SmartBase PC1270D
Fax Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
SB_PC1270D_FG_EN.book Page iii Monday, February 18, 2002 12:20 PM
Contents
Chapter 1: Introduction
Chapter 4: Sending Faxes
Customer Support.................................................1-1
Operation Panel ....................................................1-1
Standby Display ....................................................1-3
Preparing to Send a Fax .......................................4-1
Documents You Can Fax...................................4-1
Adjusting the Quality of Your Faxes...................4-1
Dialling Methods ................................................4-2
Sending Methods ..................................................4-5
Memory Sending................................................4-5
Cancelling Sending ...............................................4-7
Redialling When the Line is Busy..........................4-8
Manual Redialling ..............................................4-8
Automatic Redialling ..........................................4-8
Sequential Broadcasting .......................................4-9
Delayed Sending.................................................4-11
Confirming Transmission Status and Sending
Reservation.........................................................4-12
Confirming Transmission Status......................4-12
Confirming Sending Reservation .....................4-12
Documents Stored in Memory.............................4-13
Printing a List of Documents in Memory ..........4-13
Resending a Document in Memory..................4-14
Printing a Document in Memory.......................4-15
Deleting a Document from Memory .................4-16
Chapter 2: Registering Information
Methods of Registering Information in the Machine2-
1
Guidelines for Entering Numbers, Letters, and
Symbols ................................................................2-1
Correcting a Mistake..........................................2-2
Registering Sender Information ............................2-3
What is Sender Information? .............................2-3
Entering the Date and Time...............................2-4
Registering Your Fax/Telephone Number and
Name .................................................................2-4
Printing a List to Check Information Registered in
Your Machine.....................................................2-6
Setting the Telephone Line Type ..........................2-7
Dialling Through a Switchboard ............................2-7
Chapter 3: Speed Dialling
What is Speed Dialling?........................................3-1
Speed Dialling Methods.....................................3-1
One-Touch Speed Dialling....................................3-2
Registering Numbers for One-Touch Speed Dialling
3-2
Changing/Deleting a One-Touch Speed Dialling
Entry...................................................................3-3
Coded Speed Dialling ...........................................3-4
Registering Numbers for Coded Speed Dialling 3-4
Changing/Deleting a Coded Speed Dialling Entry3-
5
Group Dialling .......................................................3-7
Creating Groups.................................................3-7
Speed Dialling Lists...............................................3-9
Printing Speed Dialling Lists ..............................3-9
Cancelling the Print Out List ............................3-11
Registering a Password and Subaddress...........3-12
Chapter 5: Receiving Faxes
Different Ways to Receive a Fax...........................5-1
Setting the Receive Mode.....................................5-2
Setting the Options for FaxTel Mode .................5-3
Receiving Faxes Manually ....................................5-5
Registering a Password and Subaddress for Polling.
5-6
Receiving While Performing Other Tasks .............5-8
Receiving Faxes in Memory When a Problem Occurs
5-8
Cancelling Receiving.............................................5-8
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
SB_PC1270D_FG_EN.book Page iv Monday, February 18, 2002 12:20 PM
Chapter 6: Special Features
Special Dialling......................................................6-1
Dialling an Overseas Number (With Pauses) ....6-1
Switching Temporarily to Tone Dialling..............6-2
Confirming a Dial Tone ......................................6-3
Dialling Through a Switchboard.........................6-3
Restricting Use of Your Machine...........................6-4
Chapter 7: Reports and Lists
Summary of Reports and Lists .............................7-1
ACTIVITY REPORT..............................................7-2
TX (Transmission) REPORT.................................7-3
MULTI TX/RX (Transaction) REPORT ..............7-4
RX (Reception) REPORT......................................7-4
Chapter 8: Troubleshooting
LCD Messages......................................................8-1
Faxing Problems ...................................................8-2
Sending Problems..............................................8-2
Receiving Problems...........................................8-3
Telephone Problems.............................................8-5
If a Power Cut Occurs...........................................8-5
If You Cannot Solve the Problem..........................8-6
Chapter 9: Setting the Additional Functions
Understanding the “Additional Functions”.............9-1
Accessing the Additional Functions ...................9-1
Menu Descriptions .............................................9-2
Appendix: Specifications
Facsimile ............................................................. A-1
Telephone ............................................................ A-1
Index...............................................................I-1
iv
Download from Www.Somanuals.com. All Manuals Search And Download.
SB_PC1270D_FG_EN.book Page v Monday, February 18, 2002 12:20 PM
Type Conventions Used in This Guide
Please read the following list of symbols, terms, and abbreviations used in this guide.
• Indicates a warning concerning operations that may lead to death or injury to persons or damage to property
if not performed correctly. In order to use the machine safely, always pay attention to these warnings.
• Indicates an operational warning or restriction. Be certain to read these items to operate the machine correctly, and to
avoid damage to the machine.
• Indicates a note for operation or an additional explanation. Reading these is highly recommended.
(→ p. n-nn)
A number preceded by an arrow and enclosed in parenthesis refers to a page in this guide where
more information on the topic of the previous sentence can be found.
→ Quick Start Guide
→ Reference Guide
machine
Refer to the Quick Start Guide for details on the topic of the previous sentence.
Refer to the Reference Guide for details on the topic of the previous sentence.
The word “machine” refers to the PC1270D.
default
A setting that remains in effect unless you change it.
document or fax
menu
The original sheet(s) of paper you send or receive with the machine.
A list of settings from which you select an item to set up or change. A menu has a title which appears
in the LCD.
transaction number
When you send or receive a document, your machine automatically assigns the document a unique
transaction number. A transaction number is a four-digit number that will help you keep track of
documents you send and receive.
TX/RX NO.
TX/RX NO. is the abbreviation used for Transaction number.
Denotes Sending.
TX
RX
Denotes Receiving.
In addition, this guide uses distinctive typefaces to identify keys and information in the LCD:
• The keys you press appear in this typeface: Stop/Reset.
• Information in the LCD appears in this typeface: FAX SETTINGS.
v
Download from Www.Somanuals.com. All Manuals Search And Download.
SB_PC1270D_FG_EN.book Page vi Monday, February 18, 2002 12:20 PM
vi
Download from Www.Somanuals.com. All Manuals Search And Download.
01_EN.fm Page 1 Tuesday, February 19, 2002 8:13 AM
Chapter 1
Introduction
Customer Support
Your machine is designed with the latest technology to provide trouble-free operation. If you encounter a problem with the
machine’s operation, try to solve it by using the information in Chapter 8. If you cannot solve the problem or if you think your
machine needs servicing, contact your local authorised Canon dealer or the Canon Help Desk.
1
Operation Panel
This section describes keys used when sending and receiving faxes. For buttons not described here, → Reference Guide.
FAX Key
LCD
Switches standby display to Fax Mode.
Displays messages and
selections, and prompts during
operation.
In Use/Memory indicator
Flashes green when a fax is being received or
sent. Lights green when the reservation of fax
transmission is set, or a fax is received into
the memory.
Alarm indicator
Additional Functions
Key
Customises the way your
machine operates.
Flashes orange when the machine has
a problem such as paper jams, etc.
(The error message is displayed in the
LCD).
Energy Saver Key
Sets or cancels the energy saver
mode manually.
The key lights green when the
energy saver mode is set, or
goes off when the mode is
cancelled.
COPY Key
Switches standby
display to Copy
Mode.
Function
Fax Monitor
R
Redial / Pause
Coded Dial
Directory
ABC
JKL
DEF
MNO
Memory
Reference
D.T.
Report
Tone / +
Space
Delete
Clear
GHI
Delayed
Transmission
Receive Mode
Fax Resolution
PQRS
TUV
WXYZ
Book Sending
(–),
(+) Keys
Numeric Keys
Start Key
Starts sending faxes.
Scroll through the selection Enter numbers when
so you can see other
selections.
dialling or registering fax/
telephone numbers.
Also enter characters
when registering names.
Stop/Rest Key
Cancels sending or receiving
faxes and other operations, and
returns the machine to standby
mode.
OK Key
Determines the contents you set or registered.
Also, if the document being scanned stops in the ADF,
pressing this key makes the document come out
automatically.
1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
SB_PC1270D_FG_EN.book Page 2 Monday, February 18, 2002 12:20 PM
One-Touch Speed Dialling Keys
The keys marked 01 to 12 can be used to dial fax/telephone numbers pre-registered under these keys. To dial using
these keys, you need to register the numer for one-touch speed dialling.
When the Function key is pressed and the indicator lights green, the following keys can be used for the fax
functions.
Also, if fax functions are programmed into these keys, they can be used directly as One-Touch Keys without
pressing Function to execute the fax functions.
Fax Monitor Key
Confirms the status of fax communication.
Memory Reference Key
Confirms documents stored in the machine for memory sending or memory receiving.
Report Key
Prints the report listing fax communications, dial list, data list or document list.
Delayed Transmission Key
Specifies the fax sending time for the delayed sending function.
Book Sending Key
This key can be used to send documents from the platen glass.
R Key
Press to dial an outside telephone number, or an extension number, when the fax is connected through a
switchboard (PBX).
D.T. Key
Press to confirm the dial tone when registering a telephone number.
Tone/+ Key
Enters a plus sign in a fax number. Connects to information services that accept tone dialling only, even if you are
using a rotary pulse.
Space Key
Enters a space between letters and numbers.
Delete Key
Deletes a character one by one.
Clear Key
Deletes all characters.
Function Key
After pressing this key, you can use the keys marked 01 to 12 (except for
06) for the fax functions.
Lights green when the key is pressed and goes off when the key is
pressed again.
Function
Fax Monitor
R
Redial/Pause Key
Dials the last number dialled with the numeric keys, or inserts a pause
within and/or after a number.
Redial / Pause
Coded Dial
Directory
Memory
Reference
D.T.
Coded Dial Key
Report
Tone / +
Space
Delete
Clear
The key can be used to dial fax/telephone numbers pre-registered under a
two-digit code. To dial by using this key, you need to register a number for
the coded speed dialling.
Delayed
Transmission
Receive Mode
Fax Resolution
Directory Key
Book Sending
Searches fax/telephone numbers pre-registered under the One-Touch
Speed Dialling Keys or Coded Speed Dialling Keys using the names of the
registers.
Receive Mode Key
Selects the receive mode.
Fax Resolution Key
Selects the fax resolution: STANDARD, FINE, PHOTO, SUPER FINE or ULTRA
FINE.
1-2
Download from Www.Somanuals.com. All Manuals Search And Download.
SB_PC1270D_FG_EN.book Page 3 Monday, February 18, 2002 12:20 PM
Standby Display
The standby display differs depending on which mode is selected. When the machine is plugged in, the Copy Mode standby
display appears. You can switch Copy Mode to Fax Mode by pressing FAX.
The standby display in Fax Mode is as follows:
■ Fax Mode
1
Copy Quantity
FAX 03/12 2001 15:30
FaxTel
STANDARD
Receive Mode
Fax Resolution
• The standby display in Copy Mode is, → Reference Guide.
1-3
Download from Www.Somanuals.com. All Manuals Search And Download.
SB_PC1270D_FG_EN.book Page 4 Monday, February 18, 2002 12:20 PM
1-4
Download from Www.Somanuals.com. All Manuals Search And Download.
SB_PC1270D_FG_EN.book Page 1 Monday, February 18, 2002 12:20 PM
Chapter 2
Registering Information
Methods of Registering Information in the Machine
To customise the machine to your particular needs, you can adjust the general operation, sending, receiving, printing, system
settings, and speed dialling settings.
You can adjust settings directly via the operation panel of the machine. Detailed instructions are described in this guide.
2
Guidelines for Entering Numbers, Letters, and Symbols
When you come to a step that requires you to enter a name or number, refer to the table below to determine which numeric key
to press for the character you want:
Key
Uppercase Letter
Lowercase Letter
Number Mode
Mode (:A)
Mode (:a)
(:1)
1
ABC
1
2
3
4
5
6
7
8
9
0
2
3
4
5
ABCÅÄÁÀÃÂÆÇ abcåäáàãâæç
DEF
DEF-DËÉÈÊ
GHIÏÍÌÎ
defdëéèê
ghiïíìî
GHI
JKL
JKL
jkl
MNO
6
PQRS
MNOÑØÖÓÒÕÔ
PQRS
mnoñøöóòõô
pqrs
7
TUV
8
WXYZ
TUVÜÚÙÛ
WXYZY
tuvüúùû
wxyzy
9
0
#
– . A # ! " , ; : ^ ` _ = ⁄ | ’ ? $ @ % & +
( ) [ ] { } < >
Uppercase Letter
Mode (:A)
Lowercase Letter
Mode (:a)
Number Mode (:1)
• If you do not press any key for more than 2 minutes, when you enter data, the machine will automatically return to standby mode with
the auto clear function.
• AUTO CLEAR can be set within a range of 1 to 9 minutes at one minute intervals. You can also disable the auto clear function, →
Reference Guide.
2-1
Download from Www.Somanuals.com. All Manuals Search And Download.
SB_PC1270D_FG_EN.book Page 2 Monday, February 18, 2002 12:20 PM
• The Function key will light up by pressing Function to be able to operate Space, Delete or Clear.
■ Entering Letters
1
2
Press to switch to uppercase letter mode (:A) or lowercase letter mode
(:a).
:A
:A
Ex:
Ex:
Press the numeric key that contains the letter you want.
• Press repeatedly until the letter you want appears. Each key cycles through the
letters it contains.
C
• If you are unsure which key to press for the letter you want, → p. 2-1.
3
Continue entering other letters using the numeric keys.
• If the next letter you want to enter is under a different numeric key, simply press
that key until the letter you want appears.
:A
CA
Ex:
-or-
If the next letter you want to enter is under the same numeric key you pressed in
step 2, use (+) to move the cursor to the right. Then press that same numeric
key repeatedly until the letter you want appears.
• Press Space to enter a space and move the cursor to the right.
■ Entering Symbols
1
2
3
Press to switch to letter mode (:A) or (:a).
:A
:A
:A
_
Ex:
Ex:
Ex:
Press repeatedly until the symbol you want appears.
If you want to enter another symbol, use (+) to move the cursor to the
right, then press repeatedly until the symbol you want appears.
-
■ Entering Numbers
1
2
3
Press to switch to number mode (:1).
:1
:1
:1
_
Ex:
Ex:
Ex:
Press the numeric key that contains the number you want.
• Press Space to enter a space and move the cursor to the next digit.
1_
10_
Continue entering other numbers using the numeric keys.
■ Correcting a Mistake
If you make a mistake while entering letters or numbers, you can delete it by pressing Delete or Clear.
■ To Delete the Last Letter/Number
Press Delete once to delete the last letter or the last number you entered.
■ To Delete All Letters/Numbers
Press Clear to delete all letters or all numbers you entered.
2-2
Download from Www.Somanuals.com. All Manuals Search And Download.
SB_PC1270D_FG_EN.book Page 3 Monday, February 18, 2002 12:20 PM
Registering Sender Information
■ What is Sender Information?
When you receive a fax, the name of the person or company who sent you the fax, their fax/telephone number, and the date and
time of transmission may be printed in small type at the top of each page. This information is called the Sender information or
the Transmit Terminal Identification (TTI). Similarly, you can register your details in your machine so that whenever you send
a fax, the other party knows who sent it, and when it was sent. Below is an example of how your sender information would be
printed on a fax sent from your machine:
03/12 2001 15:33 FAX 123 4567
CANON
CANON CANADA
001/001
2
DATE AND TIME
Date and time of
transmission.
THE SLEREXE COMPANY LIMITED
SAPORS LANE•BOOLE•DORSET•BH25 8ER
TELEPHONE BOOLE (945 13) 51617
–
FAX 1234567
FAX/TELEPHONE
NUMBER
Your fax/telephone
number.
You can select FAX or TEL
to be displayed in front of
the number.
Our Ref. 350/PJC/EAC
(→ p. 9-4)
UNIT NAME
Your name or
company name.
DESTINATION
If you used memory sending and dialled the
fax number using one-touch or coded speed
dialling, the other party’s name appears
here.
PAGE NUMBER
The page number of the
fax.
• You can set the sender information to print inside or outside the image area. (→ p. 9-4)
• You can enter the sender information from the Additional Functions. (→ p. 9-4)
2-3
Download from Www.Somanuals.com. All Manuals Search And Download.
02_EN.fm Page 4 Tuesday, February 19, 2002 8:20 AM
■ Entering the Date and Time
1
Press Additional Functions.
2
Use (–) or (+) to select 5.TIMER SETTINGS.
ADDITIONAL FUNCTIONS
5.TIMER SETTINGS
3
4
Press OK twice.
TIMER SETTINGS
The date and time currently set for the machine are displayed.
1.DATE/TIME SETTING
DATE/TIME SETTING
03/12 ’01 12:10
Ex:
Ex:
Use the numeric keys to enter the correct day, month, year, and time in this
order.
• Use (–) or
then press the numeric key.
DATE/TIME SETTING
03/12 ’01 15:30
(+) to move the cursor under the number you want to change,
• Enter only the last two digits of the year.
• Use the 24-hour format for the time setting (e.g. 1:00 p.m. as 13:00).
5
6
Press OK.
DATE/TIME SETTING
DATA ENTRY OK
TIMER SETTINGS
2.AUTO CLEAR
Press Stop/Reset to return to standby display.
■ Registering Your Fax/Telephone Number and Name
• The Function key will light up by pressing Function to be able to operate the Space, Delete, Clear or Tone/+ key.
1
2
Press Additional Functions.
Use (–) or (+) to select 3.FAX SETTINGS.
ADDITIONAL FUNCTIONS
3.FAX SETTINGS
3
Press OK four times.
FAX SETTINGS
1.USER SETTINGS
USER SETTINGS
1.TEL LINE SETTINGS
TEL LINE SETTINGS
1.USER TEL NO.
USER TEL NO.
TEL=
Ex:
Ex:
4
Use the numeric keys to enter your fax number (max. 20 digits, including
spaces).
• If you have already registered your fax/telephone number, previous entry will be
displayed. To change your fax/telephone number, use the numeric keys to enter
your fax number.
USER TEL NO.
TEL=
123 4567
• Press Space to enter a space.
• To enter a plus sign (+) before the number, press the Tone/+ key.
• If you make a mistake, press Delete to delete the last number or press Clear to
delete all numbers you entered.
2-4
Download from Www.Somanuals.com. All Manuals Search And Download.
02_EN.fm Page 5 Tuesday, February 19, 2002 8:20 AM
5
Press OK.
USER TEL NO.
DATA ENTRY OK
TEL LINE SETTINGS
2.TEL LINE TYPE
6
7
8
9
Press Additional Functions.
Use (–) or (+) to select 2.UNIT NAME.
Press OK.
USER SETTINGS
1.TEL LINE SETTINGS
USER SETTINGS
2.UNIT NAME
2
:A
_
Ex:
Ex:
Use the numeric keys to enter your name or company name (max. 24
characters, including spaces).
• If you are unsure how to enter characters, → p. 2-1.
• If you have already registered your name or company name, the previous entry
will be displayed. To change your name, press Clear to delete the previous entry
and re-enter.
:A
CANON
• Press Space to enter a space and move the cursor to the right.
• If you make a mistake, press Delete to delete the last character, or press Clear
to delete all characters you entered.
10 Press OK.
:A
DATA ENTRY OK
Ex:
USER SETTINGS
3.TX TERMINAL ID
11 Press Stop/Reset to return to standby display.
2-5
Download from Www.Somanuals.com. All Manuals Search And Download.
02_EN.fm Page 6 Tuesday, February 19, 2002 8:20 AM
■ Printing a List to Check Information Registered in Your Machine
You can print the USER’S DATA LIST to check the sender information and current settings of your machine.
1
2
Press Additional Functions.
Use (–) or (+) to select 7.PRINT LISTS.
ADDITIONAL FUNCTIONS
7.PRINT LISTS
3
Press OK twice.
PRINT LISTS
1.USER DATA
• The machine returns to standby mode then prints the USER’S DATA LIST.
The sender information is shown at the beginning of the list. The current settings of the machine are listed after this.
03/12 2001 16:40 FAX 123 4567
CANON
001
✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱
✱✱✱ USER’S DATA LIST ✱✱✱
✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱
1.COMMON SETTINGS
DEFAULT SETTINGS
SW AFTER AUTO CLR
VOLUME CONTROL
KEYPAD VOLUME
VOLUME
COPY
DEFAULT MODE
ON
1
ALARM VOLUME
VOLUME
ON
1
TX DONE TONE
VOLUME
ERROR ONLY
1
2-6
Download from Www.Somanuals.com. All Manuals Search And Download.
SB_PC1270D_FG_EN.book Page 7 Monday, February 18, 2002 12:20 PM
Setting the Telephone Line Type
Before using your machine, you need to make sure it is set for your telephone line type. If you are unsure of your telephone line
type, check with your local telephone company. The factory default setting of your machine varies depending on the current
country selection. You can print the USER’S DATA LIST to check the current setting. (→ p. 2-6). If you need to change the
setting, follow this procedure.
1
2
Press Additional Functions.
Use (–) or (+) to select 3.FAX SETTINGS.
ADDITIONAL FUNCTIONS
3.FAX SETTINGS
2
3
Press OK three times.
FAX SETTINGS
1.USER SETTINGS
USER SETTINGS
1.TEL LINE SETTINGS
TEL LINE SETTINGS
1.USER TEL NO.
4
5
6
Use (–) or (+) to select 2.TEL LINE TYPE.
Press OK.
TEL LINE SETTINGS
2.TEL LINE TYPE
TEL LINE TYPE
TOUCH TONE
Ex:
Ex:
Use (–) or (+) to select the telephone line type setting you want to set.
• You can select from the following:
– ROTARY PULSE (For pulse dialling)
TEL LINE TYPE
ROTARY PULSE
– TOUCH TONE (For tone dialling)
7
8
Press OK.
TEL LINE SETTINGS
3.TX START SPEED
Press Stop/Reset to return to standby display.
Dialling Through a Switchboard
A PBX (Private Branch Exchange) is an on-site telephone switchboard. If your machine is connected through a PBX or other
telephone switching system, you have to dial the outside line access number first, and then the number of the party you are
calling.
To facilitate this procedure, you can register the PBX access type and the outside line access number under the R key so that
you only need to press this key before dialling the fax/telephone number you want to reach. See below for details.
The settings available and the factory default setting vary depending on the current country selection. You can print the USER’S
DATA LIST to check the current setting. (→ p. 2-6)
1
2
Press Additional Functions.
Use (–) or (+) to select 3.FAX SETTINGS.
ADDITIONAL FUNCTIONS
3.FAX SETTINGS
2-7
Download from Www.Somanuals.com. All Manuals Search And Download.
SB_PC1270D_FG_EN.book Page 8 Monday, February 18, 2002 12:20 PM
3
Press OK twice.
FAX SETTINGS
1.USER SETTINGS
USER SETTINGS
1.TEL LINE SETTINGS
4
5
6
7
8
Use (–) or (+) to select R-KEY SETTING.
USER SETTINGS
7.R-KEY SETTING
Press OK.
R-KEY SETTING
PSTN
Use (–) or (+) to select PBX.
R-KEY SETTING
PBX
Press OK.
PBX
EARTH CONNECTION
Ex:
Ex:
Use (–) or (+) to select the access type of your switching system.
PBX
HOOKING
❚ If you selected HOOKING or EARTH CONNECTION in step 8:
Press OK.
9
FAX SETTINGS
2.REPORT SETTINGS
10 Press Stop/Reset to return to standby display.
❚ If you selected PREFIX in step 8:
9
Press OK.
PREFIX
10 Use the numeric keys to enter the outside line access number (max. 20
PREFIX
123456
digits).
Ex:
Ex:
11 Press Redial/Pause to enter a pause.
12 Press OK.
PREFIX
123456P
FAX SETTINGS
2.REPORT SETTINGS
13 Press Stop/Reset to return to standby display.
2-8
Download from Www.Somanuals.com. All Manuals Search And Download.
SB_PC1270D_FG_EN.book Page 1 Monday, February 18, 2002 12:20 PM
Chapter 3
Speed Dialling
What is Speed Dialling?
Speed dialling allows you to simplify dialling procedures by registering a fax/telephone number(s) and name under a one-touch
speed dialling key or coded speed dialling keys. You can then dial that number by pressing only one or a few keys.
■ Speed Dialling Methods
There are three speed dialling methods available with your machine as follows:
■ One-Touch Speed Dialling (→ p. 3-2)
3
Allows you to dial a fax or telephone number by pressing only one key. You can register up to 12 destinations for one-touch
speed dialling.
■ Coded Speed Dialling (→ p. 3-4)
Allows you to dial a fax or telephone number by pressing Coded Dial followed by a two-digit code of your choice. You
can register up to 100 different destinations.
■ Group Dialling (→ p. 3-7)
Allows you to dial a group of registered one-touch and/or coded speed dialling fax numbers. By registering a group for one-
touch or coded speed dialling, you press only one or a few keys to send the same document to several destinations.
The following pages describe how to register numbers for speed dialling.
• For instructions on dialling using the speed dialling methods, → pp. 4-3, 4-4.
3-1
Download from Www.Somanuals.com. All Manuals Search And Download.
SB_PC1270D_FG_EN.book Page 2 Monday, February 18, 2002 12:20 PM
One-Touch Speed Dialling
■ Registering Numbers for One-Touch Speed Dialling
• The Function key will light up by pressing Function to be able to operate Space, Delete or Clear.
1
2
Press Additional Functions.
Use (–) or (+) to select 4.ADD. REGISTRATION.
ADDITIONAL FUNCTIONS
4.ADD. REGISTRATION
3
Press OK twice.
ADD. REGISTRATION
1.1-TOUCH SPD DIAL
1-TOUCH SPD DIAL
01=
905 795 1111
Ex:
Ex:
4
Use (–) or (+) to select a one-touch speed dialling key (01 to 12).
• You can directly select the one-touch speed dialling key by pressing it.
• If a one-touch speed dialling key has already been registered, the number
registered under that key appears.
1-TOUCH SPD DIAL
04=
• If a group is already registered under a one-touch speed dialling key, GROUP DIAL appears.
• If the fax functions have been programmed into the keys marked 01 to 12 using PROG 1-TOUCH KEY in the Additional
Functions, PROG 1-TOUCH KEY will appear.
5
6
Press OK twice.
1-TOUCH SPD DIAL
1.TEL NUMBER ENTRY
TEL NUMBER ENTRY
TEL=_
Use the numeric keys to enter the fax/telephone number you want to
register (max. 120 digits, including spaces and pauses).
• Press Space to enter a space and move the cursor to the next digit. Spaces are
optional and are ignored during dialling.
TEL NUMBER ENTRY
TEL=2 50921_
Ex:
• Press Redial/Pause to enter a pause.
• If you make a mistake, move the cursor to the last number by pressing (–), and press Delete repeatedly to delete the
numbers one by one starting from the last number. Or, press Clear to delete all the numbers you have entered.
7
8
Press OK twice.
TEL NUMBER ENTRY
DATA ENTRY OK
1-TOUCH SPD DIAL
2.NAME
:A
:A
_
Use the numeric keys to enter the name that goes with the number (max.
16 characters, including spaces).
• If you are unsure how to enter characters, → p. 2-1.
Canon ITALIA
Ex:
3-2
Download from Www.Somanuals.com. All Manuals Search And Download.
03_EN.fm Page 3 Tuesday, February 19, 2002 8:21 AM
9
Press OK.
:A
• For details of OPTIONAL SETTING, refer to the following items as required.
– Registering a Password and Subaddress (→ p. 3-12)
– Registering a Password and Subaddress for Polling (→ p. 5-7)
– TX TIME SETTING in the Additional Functions (→ p. 9-9)
DATA ENTRY OK
1-TOUCH SPD DIAL
3.OPTIONAL SETTING
Ex:
10 To continue registering other one-touch speed dialling keys, press Additional Functions then repeat the
procedure from step 4.
– or –
Press Stop/Reset to return to standby display.
• You can use the destination labels. Put these labels on your machine for easy reference when dialling.
■ Changing/Deleting a One-Touch Speed Dialling Entry
• The Function key will light up by pressing Function to be able to operate Space, Delete or Clear.
3
1
2
Follow steps 1 to 3 of “Registering Numbers for One-Touch Speed
Dialling.” (→ p. 3-2)
Use (–) or (+) to select the one-touch speed dialling key assigned to
the entry you want to change or delete.
• You can directly select the one-touch speed dialling key by pressing it.
1-TOUCH SPD DIAL
06=
1 432 2015
Ex:
3
Press OK twice.
1-TOUCH SPD DIAL
1.TEL NUMBER ENTRY
TEL NUMBER ENTRY
TEL=1 432 2015_
❚ To Change a One-Touch Speed Dialling Entry:
4
Press Function, then Clear to delete the previous entry, then re-enter the
fax/telephone number.
• If you do not want to change the fax/telephone number, ignore this step.
• Press Space to enter a space and move the cursor to the next digit. Spaces are
optional and are ignored during dialling.
TEL NUMBER ENTRY
TEL=1 432 2060_
Ex:
• Press Redial/Pause to enter a pause.
• If you make a mistake, move the cursor to the last number by pressing (–), and
press Delete repeatedly to delete the numbers one by one starting from the last
number. Or, press Clear to delete all the numbers you have entered.
5
6
Press OK twice.
TEL NUMBER ENTRY
DATA ENTRY OK
1-TOUCH SPD DIAL
2.NAME
:A
Canon OPTIX_
Canon OPTICS
Ex:
Ex:
Press Clear to delete the previous entry, then re-enter the name.
• If you do not want to change the name, ignore this step.
• If you are unsure how to enter characters, → p. 2-1.
:A
3-3
Download from Www.Somanuals.com. All Manuals Search And Download.
03_EN.fm Page 4 Tuesday, February 19, 2002 8:21 AM
7
8
Press OK.
:A
DATA ENTRY OK
1-TOUCH SPD DIAL
3.OPTIONAL SETTING
Press Stop/Reset to return to standby display.
❚ To Delete a One-Touch Speed Dialling Entry:
4
5
Press Function, then Clear to delete the fax/telephone number.
TEL NUMBER ENTRY
TEL=
Press OK.
TEL NUMBER ENTRY
ERASING END
1-TOUCH SPD DIAL
2.NAME
6
Press Stop/Reset to return to standby display.
• The registered name is automatically cleared when you clear the fax/telephone
number.
Coded Speed Dialling
■ Registering Numbers for Coded Speed Dialling
• The Function key will light up by pressing Function to be able to operate Space, Delete or Clear.
1
2
Press Additional Functions.
Use (–) or (+) to select 4.ADD. REGISTRATION.
ADDITIONAL FUNCTIONS
4.ADD. REGISTRATION
3
4
5
6
Press OK.
ADD. REGISTRATION
1.1-TOUCH SPD DIAL
Use (–) or (+) to select 2.CODED SPD DIAL.
Press OK.
ADD. REGISTRATION
2.CODED SPD DIAL
CODED SPD DIAL
00=
2131 1250
Ex:
Ex:
Use (–) or (+) to select a coded speed dialling code (00 to 99).
• You can also select a code by pressing Coded Dial and then entering a two-digit
code with the numeric keys.
CODED SPD DIAL
02=
• If a coded speed dialling code has already been registered, the number registered
under that code appears.
• If a group is already registered under a coded speed dialling code, GROUP DIAL
appears.
7
Press OK twice.
CODED SPD DIAL
1.TEL NUMBER ENTRY
TEL NUMBER ENTRY
TEL=_
3-4
Download from Www.Somanuals.com. All Manuals Search And Download.
03_EN.fm Page 5 Tuesday, February 19, 2002 8:21 AM
8
9
Use the numeric keys to enter the fax/telephone number you want to
register (max. 120 digits, including spaces and pauses).
• Press Space to enter a space and move the cursor to the next digit. Spaces are
optional and are ignored during dialling.
TEL NUMBER ENTRY
TEL=1 49 39 25 25_
Ex:
• Press Redial/Pause to enter a pause.
• If you make a mistake, move the cursor to the last number by pressing (–), and
press Delete repeatedly to delete the numbers one by one starting from the last
number. Or, press Clear to delete all the numbers you have entered.
Press OK twice.
TEL NUMBER ENTRY
DATA ENTRY OK
CODED SPD DIAL
2.NAME
:A
:A
3
_
10 Use the numeric keys to enter the name that goes with the number (max.
16 characters, including spaces).
Canon FRANCE
Ex:
Ex:
• If you are unsure how to enter characters, → p. 2-1.
11 Press OK.
:A
• For details of OPTIONAL SETTING, refer to the following items as required.
– Registering a Password and Subaddress (→ p. 3-12)
– Registering a Password and Subaddress for Polling (→ p. 5-7)
– TX TIME SETTING in the Additional Functions (→ p. 9-9)
DATA ENTRY OK
CODED SPD DIAL
3.OPTIONAL SETTING
12 To continue registering other coded speed dialling codes, press
Additional Functions then repeat the procedure from step 6.
– or –
Press Stop/Reset to return to standby display.
• You can print the CODED DIAL LIST showing all the numbers and names
registered for coded speed dialling (→ pp. 3-9, 3-10). Keep this list near your
machine for easy reference when dialling.
■ Changing/Deleting a Coded Speed Dialling Entry
• The Function key will light up by pressing Function to be able to operate Space, Delete or Clear.
1
2
Follow steps 1 to 5 of “Registering Numbers for Coded Speed Dialling.”
(→ p. 3-4)
Use (–) or (+) to select the coded speed dialling code assigned to the
entry you want to change or delete.
• You can also select the code by pressing Coded Dial and then entering the two-
digit code with the numeric keys.
CODED SPD DIAL
32= 81 773 3115
Ex:
3
Press OK twice.
CODED SPD DIAL
1.TEL NUMBER ENTRY
TEL NUMBER ENTRY
TEL=81 773 3115_
3-5
Download from Www.Somanuals.com. All Manuals Search And Download.
03_EN.fm Page 6 Tuesday, February 19, 2002 8:21 AM
❚ To Change a Coded Speed Dialling Entry:
4
5
Press Function, then Clear to delete the previous entry, then re-enter the
fax/telephone number.
• If you do not want to change the fax/telephone number, ignore this step.
• Press Space to enter a space and move the cursor to the next digit. Spaces are
optional and are ignored during dialling.
TEL NUMBER ENTRY
TEL=81 773 3173_
Ex:
• Press Redial/Pause to enter a pause.
• If you make a mistake, move the cursor to the last number by pressing (–), and
press Delete repeatedly to delete the numbers one by one starting from the last
number. Or, press Clear to delete all the numbers you have entered.
Press OK twice.
TEL NUMBER ENTRY
DATA ENTRY OK
CODED SPD DIAL
2.NAME
:A
:A
Canon UC_
Canon UK
Ex:
Ex:
6
7
Press Function, then Clear to delete the previous entry, then re-enter the
name.
• If you do not want to change the name, ignore this step.
• If you are unsure how to enter characters, → p. 2-1.
Press OK.
:A
DATA ENTRY OK
CODED SPD DIAL
3.OPTIONAL SETTING
8
Press Stop/Reset to return to standby display.
❚ To Delete a Coded Speed Dialling Entry:
4
5
Press Function, then Clear to delete the fax/telephone number.
TEL NUMBER ENTRY
TEL=
Press OK.
TEL NUMBER ENTRY
ERASING END
CODED SPD DIAL
2.NAME
6
Press Stop/Reset to return to standby display.
• The registered name is automatically cleared when you clear the fax/telephone
number.
3-6
Download from Www.Somanuals.com. All Manuals Search And Download.
SB_PC1270D_FG_EN.book Page 7 Monday, February 18, 2002 12:20 PM
Group Dialling
■ Creating Groups
• The Function key will light up by pressing Function to be able to operate Clear.
1
2
Press Additional Functions.
Use (–) or (+) to select 4.ADD. REGISTRATION.
ADDITIONAL FUNCTIONS
4.ADD. REGISTRATION
3
4
5
6
Press OK.
ADD. REGISTRATION
1.1-TOUCH SPD DIAL
3
Use (–) or (+) to select 3.GROUP DIAL.
Press OK.
ADD. REGISTRATION
3.GROUP DIAL
GROUP DIAL
01=1-TOUCH SPD DIAL
Ex:
Select a one-touch speed dialling key or coded speed dialling code under
which you want to register the group.
• If you wish to register a group under the already registered one-touch speed dialling
key or coded speed dialling code, or you want to re-enter a group, you must delete
the previous information first. (→ pp. 3-3, 3-5, 3-6)
• Do not register a group under a one-touch speed dialling key or coded speed
dialling code, in which SUBADDRESS TX or POLLING RX has been set. If you
do so, you cannot send faxes to the other party’s which have a subaddress
registered.
❚ To register a group under a one-touch speed dialling key:
Use (–) or (+) to select the key under which you want to register the
group (01 to 12).
• If a one-touch speed dialling key has already been registered, 1-TOUCH SPD
DIAL or GROUP DIAL appears.
GROUP DIAL
03=
Ex:
• If the fax functions have been programmed into the keys marked 01 to 12 using
PROG 1-TOUCH KEY in the Additional Functions, PROG 1-TOUCH KEY will
appear.
❚ To register a group under a coded speed dialling code:
Press Coded Dial, then use the numeric keys to enter the code under
which you want to register the group (00 to 99).
• If a coded speed dialling code has already been registered, CODED SPD DIAL
or GROUP DIAL appears.
GROUP DIAL
21=
Ex:
7
Press OK twice.
GROUP DIAL
1.TEL NUMBER ENTRY
TEL=
3-7
Download from Www.Somanuals.com. All Manuals Search And Download.
SB_PC1270D_FG_EN.book Page 8 Monday, February 18, 2002 12:20 PM
8
Enter the one-touch and/or coded speed dialling numbers you want to
register in the group.
• You cannot register numbers in groups that have not been registered for speed
dialling.
• You can review the numbers registered under the group by pressing (–) or
(+).
– If you want to delete one of these numbers from the group, press (–) or (+)
to display the number you want to delete and press Clear (ERASING END is
displayed).
– If you want to delete all numbers in the group, press (–) or (+) to display
the number and press Clear repeatedly until all numbers are deleted. Deleting
all numbers will cancel the group. If there is a group that has already been
registered, the group’s name will not be deleted even if you delete all the
numbers.
• You can cancel registering numbers and return to standby display by pressing the
Stop/Reset anytime before pressing OK in step 9.
❚ To enter a destination registered for one-touch speed dialling:
Press the one-touch speed dialling key assigned to each number you want
to register in the group. Repeat for other keys.
TEL=
2 50921
04 Canon ITALIA
Ex:
Ex:
❚ To enter a destination registered for coded speed dialling:
Press Coded Dial, then use the numeric keys to enter the two-digit code
assigned to the number you want to register in the group. Repeat for other
codes.
TEL=
02 Canon FRANCE
1 49 39 25 25
9
Press OK twice.
GROUP DIAL
2.NAME
:A
:1
_
10 Use the numeric keys to enter a name for the group (max.16 characters,
including spaces).
Canon GROUP 2_
Ex:
• If you do not want to register a name, ignore this step.
• If you are unsure how to enter characters, → p. 2-1.
11 Press OK.
:1
• You can specify up to 5 different time settings for transmission time. (→ p. 9-9)
DATA ENTRY OK
GROUP DIAL
3.TX TIME SETTING
12 To continue registering other groups, press Additional Functions then
repeat the procedure from step 6.
– or –
Press Stop/Reset to return to standby display.
• You can print the GROUP DIAL LIST showing all the numbers and names
registered for group dialling (→ pp. 3-9, 3-11). Keep this list near your machine for
easy reference when dialling.
3-8
Download from Www.Somanuals.com. All Manuals Search And Download.
03_EN.fm Page 9 Tuesday, February 19, 2002 8:28 AM
Speed Dialling Lists
You can print lists of fax/telephone numbers registered for speed dialling. Keep these lists near your machine so you can refer
to them when dialling.
■ Printing Speed Dialling Lists
1
Press Additional Functions.
2
Use (–) or (+) to select 7.PRINT LISTS.
ADDITIONAL FUNCTIONS
7.PRINT LISTS
3
4
5
6
Press OK.
PRINT LISTS
1.USER DATA
3
Use (–) or (+) to select 2.SPEED DIAL LIST.
Press OK.
PRINT LISTS
2.SPEED DIAL LIST
SPEED DIAL LIST
1.1-TOUCH LIST
Use (–) or (+) to select the list you want to print.
• You can select from the following:
– 1-TOUCH LIST
– CODED DIAL LIST
– 1-TOUCH (DETAIL)
SPEED DIAL LIST
2.CODED DIAL LIST
Ex:
Ex:
– CODED (DETAIL)
– GROUP DIAL LIST
7
8
Press OK.
1-TOUCH LIST
1.NO SORT
• If you selected 1-TOUCH LIST, or 1-TOUCH (DETAIL), CODED DIAL
LIST or CODED (DETAIL) above, select SORT or NO SORT depending on
what order you want the destinations to be printed:
Select 1.NO SORT to print the list in key number order.
-or-
Select 2.SORT to print the list with the names of the destinations in alphabetical
order.
Press OK.
• The machine prints the list and returns to standby mode.
• You can also print the list using Report. Press Function (the Function key
lights up), then press Report, and select a report you want, then press OK. This
procedure must be performed in Fax Mode.
3-9
Download from Www.Somanuals.com. All Manuals Search And Download.
03_EN.fm Page 10 Tuesday, February 19, 2002 8:28 AM
Samples of the lists are shown below.
■ 1-TOUCH LIST
03/12 2001 17:02 FAX 123 4567
CANON
001
03/12 2001 17:03 FAX 123 4567
CANON
001
✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱
NO.
✱✱✱ ONE-TOUCH SPEED DIAL TEL LIST 1 ✱✱✱
✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱
[
[
[
[
[
01]
03]
04]
06]
12]
905 79
GROUP
2 5092
1 432
NO.
DESTINATION TEL
DESTINATION ID
Canon AUSTRALIA
Canon CANADA
Canon GROUP 2
Canon ITALIA
TX TYPE
[
[
[
[
[
12] 2 887 0166
REGULAR TX
REGULAR TX
2 887
01] 905 795 1111
03] GROUP DIAL
04] 2 50921
REGULAR TX
REGULAR TX
06] 1 432 2060
Canon OPTICS
UNSORTED LIST: DESTINATIONS LISTED
IN KEY ORDER.
SORTED LIST: DESTINATIONS LISTED IN
ALPHABETICAL ORDER.
■ 1-TOUCH (DETAIL)
03/12 2001 17:07 FAX 123 4567
CANON
001
03/12 2001 17:07 FAX 123 4567
CANON
001
✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱
[
[
01]
03]
DESTIN
DESTIN
✱✱✱ ONE-TOUCH SPEED DIAL TEL LIST 2 ✱✱✱
✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱
TX TYP
[
[
12] DESTINATION TEL
2 887 0166
DESTINATION ID
Canon AUSTRALIA
DESTIN
DESTIN
TX TYPE
REGULAR TX
01] DESTINATION TEL
DESTINATION ID
905 795 1111
Canon CANADA
UNSORTED LIST: DESTINATIONS LISTED
IN KEY ORDER.
SORTED LIST: DESTINATIONS LISTED IN
ALPHABETICAL ORDER.
■ CODED DIAL LIST
03/12 2001 17:04 FAX 123 4567
CANON
001
03/12 2001 17:05 FAX 123 4567
CANON
001
✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱
NO.
✱✱✱ CODED SPEED DIAL TEL LIST 1 ✱✱✱
✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱
[
[
[
[
[
00]
02]
03]
21]
32]
2131 1
1 49 3
516p48
GROUP
81 773
NO.
DESTINATION TEL
DESTINATION ID
Canon DEUTSCH.
Canon FRANCE
Canon GROUP 1
Canon U.S.A.
TX TYPE
REGULAR TX
REGULAR TX
[
[
[
[
[
00] 2131 1250
02] 1 49 39 25 25
21] GROUP DIAL
03] 516p488 6700
32] 81 773 3173
REGULAR TX
REGULAR TX
Canon UK
UNSORTED LIST: DESTINATIONS LISTED
IN KEY ORDER.
SORTED LIST: DESTINATIONS LISTED IN
ALPHABETICAL ORDER.
3-10
Download from Www.Somanuals.com. All Manuals Search And Download.
03_EN.fm Page 11 Tuesday, February 19, 2002 8:28 AM
■ CODED (DETAIL)
03/12 2001 17:07 FAX 123 4567
CANON
001
03/12 2001 17:07 FAX 123 4567
CANON
001
✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱
[
[
00]
02]
DESTIN
DESTIN
✱✱✱ CODED SPEED DIAL TEL LIST 2 ✱✱✱
✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱
TX TYP
[
[
00] DESTINATION TEL
2131 1250
DESTINATION ID
Canon DEUTSCH.
DESTIN
DESTIN
TX TYPE
REGULAR TX
02] DESTINATION TEL
DESTINATION ID
1 49 39 25 25
Canon FRANCE
3
UNSORTED LIST: DESTINATIONS LISTED
IN KEY ORDER.
SORTED LIST: DESTINATIONS LISTED IN
ALPHABETICAL ORDER.
■ GROUP DIAL LIST
03/12 2001 17:06 FAX 123 4567
CANON
001
✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱
✱✱✱ GROUP DIAL TEL LIST ✱✱✱
✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱
[
[
21] Canon GROUP 1
03] Canon GROUP 2
[
[
03] 516p488 6700
01] 905 795 1111
Canon U.S.A.
Canon CANADA
[
[
[
[
00] 2131 1250
02] 1 49 39 25 25
32] 81 773 3173
04] 2 50921
Canon DEUTSCH.
Canon FRANCE
Canon UK
Canon ITALIA
■ Cancelling the Print Out List
You can cancel printing lists even after performing the printing procedure.
1
2
Press Additional Functions.
Use (–) or (+) to select 7.PRINT LISTS.
ADDITIONAL FUNCTIONS
7.PRINT LISTS
3
4
5
6
Press OK.
PRINT LISTS
1.USER DATA
Use (–) or (+) to select 3.CANCEL REPORT.
Press OK.
PRINT LISTS
3.CANCEL REPORT
CANCEL REPORT?
<YES
NO>
Press (–).
• Printing is cancelled.
• If you change your mind and want to continue the printing, press (+).
• You can also cancel the printing by pressing Function (the Function key lights
up) then pressing Report.
3-11
Download from Www.Somanuals.com. All Manuals Search And Download.
SB_PC1270D_FG_EN.book Page 12 Monday, February 18, 2002 12:20 PM
Registering a Password and Subaddress
The password and subaddress is required when you send faxes to the other party’s fax machine that has a password and
subaddress.
• You can register the password and subaddress with a one-touch speed dialling key or coded speed dialling code.
• You must also know the password and subaddress of the other party’s fax so that you can enter them on your fax. If you do not know
the password and subaddress, contact the other party.
• The Function key will light up by pressing Function to be able to operate Space, Delete or Clear.
1
2
Press Additional Functions.
Use (–) or (+) to select 4.ADD. REGISTRATION.
ADDITIONAL FUNCTIONS
4.ADD. REGISTRATION
3
4
5
6
7
8
9
Press OK.
ADD. REGISTRATION
1.1-TOUCH SPD DIAL
Use (–) or (+) to select 1.1-TOUCH SPD DIAL or 2.CODED SPD
DIAL.
ADD. REGISTRATION
1.1-TOUCH SPD DIAL
Ex:
Ex:
Ex:
Press OK.
1-TOUCH SPD DIAL
01=
905795 1111
Use (–) or (+) to select the one-touch speed dialling number or coded
speed dialling code.
1-TOUCH SPD DIAL
02=
81 773 3115
Press OK.
1-TOUCH SPD DIAL
1.TEL NUMBER ENTRY
Use (–) or (+) to select 3.OPTIONAL SETTING.
Press OK.
1-TOUCH SPD DIAL
3.OPTIONAL SETTING
OPTIONAL SETTING
OFF
Ex:
10 Use (–) or (+) to select ON.
11 Press OK.
OPTIONAL SETTING
ON
OPTIONAL SETTING
1.TX TIME SETTNG
12 Use (–) or (+) to select 2.TX TYPE.
13 Press OK.
OPTIONAL SETTING
2.TX TYPE
TX TYPE
REGULAR TX
Ex:
14 Use (–) or (+) to select SUBADDRESS TX.
15 Press OK twice.
TX TYPE
SUBADDRESS TX
SUBADDRESS TX
1.PASSWORD
PASSWORD
Ex:
3-12
Download from Www.Somanuals.com. All Manuals Search And Download.
SB_PC1270D_FG_EN.book Page 13 Monday, February 18, 2002 12:20 PM
16 Enter a password.
PASSWORD
• You can enter a password up to 20 digits long using the numeric keys,
,
or
12345
Ex:
Space.
• Be sure to enter the password of the other party correctly, taking into account the
position of spaces.
• If you make a mistake, press Delete to delete the last character or press Clear to
delete all characters you entered.
17 Press OK twice.
SUBADDRESS TX
2.SUBADDRESS
SUBADDRESS
Ex:
Ex:
18 Enter a subaddress.
SUBADDRESS
• You can enter a subaddress up to 20 digits long using the numeric keys,
,
or
123456789012
3
Space.
• Be sure to enter the subaddress of the other party correctly, taking into account
the position of spaces.
• If you make a mistake, press Delete to delete the last character or press Clear to
delete all the characters you entered.
19 Press OK.
1-TOUCH SPD DIAL
03=GROUP DIAL
Ex:
20 To continue registering other passwords and subaddresses, press
Additional Functions then repeat the procedure from step 4.
– or –
Press Stop/Reset to return to standby display.
3-13
Download from Www.Somanuals.com. All Manuals Search And Download.
SB_PC1270D_FG_EN.book Page 14 Monday, February 18, 2002 12:20 PM
3-14
Download from Www.Somanuals.com. All Manuals Search And Download.
SB_PC1270D_FG_EN.book Page 1 Monday, February 18, 2002 12:20 PM
Chapter 4
Sending Faxes
Preparing to Send a Fax
■ Documents You Can Fax
For information on the types of documents you can fax, their requirements, and details on loading documents, → Reference
Guide.
■ Adjusting the Quality of Your Faxes
Canon’s Ultra High Quality (UHQ™) imaging technology enables you to send documents that are very close to the quality of
the original. The machine allows you to adjust the resolution and contrast to best suit your particular document.
4
• Please note that you cannot change settings while your machine is scanning a document.
Setting the Scanning Resolution
Resolution is a measure of the fineness or clarity of a printout. Low resolutions may cause text and graphics to have a jagged
appearance, while higher resolutions provide smoother curves and lines, crisp text and graphics, and a better match to traditional
typeface designs.
• The higher the resolution, the higher the output quality, but the longer the transmission time.
1
Press Fax Resolution to select the resolution.
• You can select from the following:
– STANDARD
FAX RESOLUTION
STANDARD
Ex:
Suitable for most text-only documents.
– FINE
Suitable for fine-print documents.
– PHOTO
Suitable for documents that contain photographs.
– SUPER FINE
Suitable for documents that contain fine print and images (the resolution is four
times that of STANDARD).
– ULTRA FINE
Suitable for documents that contain fine print and images (the resolution is eight
times that of STANDARD).
2
Press OK.
FAX 03/12 2001 15:30
FaxTel FINE
Ex:
• You can set the Fax Resolution so that the desired resolution such as STANDARD
is automatically returned after the AUTO CLEAR function activates or documents
are scanned. (→ p. 9-8)
Since RESOLUTION of FAX DEFAULT is set to OFF in the factory default setting,
the resolution set using Fax Resolution will remain unchanged.
4-1
Download from Www.Somanuals.com. All Manuals Search And Download.
SB_PC1270D_FG_EN.book Page 2 Monday, February 18, 2002 12:20 PM
■ Dialling Methods
There are several ways of dialling the number of the party to which you want to send a fax. They are as follows:
■ When the Fax Number is Not Registered in the Machine
• Regular Dialling
• Redialling
■ When the Fax Number is Registered in the Machine
• One-Touch Speed Dialling
• Coded Speed Dialling
• Group Dialling
• Directory Dialling
• If you are unsure of the registered fax number, check the destination labels, or print each list and check the numbers. (→ p. 3-9)
• For details on registering a fax number for speed dialling, → Chapter 3.
Regular Dialling
Dial a fax number by using the numeric keys, just like dialling a telephone number.
Ex:
1
9
0
5
9
5
1
1
1
1
7
Function
Fax Monitor
R
Redial / Pause
Coded Dial
Directory
ABC
JKL
DEF
MNO
Memory
Reference
D.T.
Tone / +
Space
Delete
Clear
Report
GHI
Delayed
Transmission
Receive Mode
Fax Resolution
PQRS
TUV
WXYZ
Book Sending
Ä Press Start.
TEL=
9057951111
Ex:
• If you enter the wrong number, press Stop/Reset or Clear to delete the number, then enter the correct number.
• The Function key will light up by pressing Function to be able to operate Clear.
4-2
Download from Www.Somanuals.com. All Manuals Search And Download.
SB_PC1270D_FG_EN.book Page 3 Monday, February 18, 2002 12:20 PM
One-Touch Speed Dialling
Dial a fax number by pressing the one-touch speed dialling key (01 to 12) to which the number is assigned.
Ex:
1
Function
Fax Monitor
R
Redial / Pause
Coded Dial
Directory
ABC
JKL
DEF
MNO
Memory
Reference
D.T.
Report
Tone / +
Space
Delete
Clear
GHI
Delayed
Transmission
Receive Mode
Fax Resolution
PQRS
TUV
WXYZ
Book Sending
4
TEL=
905 795 1111
01 Canon CANADA
Ex:
• The number registered under that one-touch speed dialling key is displayed.
• If you press the wrong key, press Stop/Reset, then press the correct key.
• NO TEL
appears if no fax number is assigned to the one-touch speed dialling key you pressed.
Coded Speed Dialling
Dial a fax number by pressing Coded Dial followed by the two-digit code (00 to 99) to which the number is assigned.
Ex:
1
Coded Dial
2
0
2
Function
Fax Monitor
R
Redial / Paus
Coded Dial
Directory
ABC
JKL
DEF
MNO
Memory
Reference
D.T.
Report
Tone / +
Space
Delete
Clear
GHI
Delayed
Transmission
Receive Mode
Fax Resolution
PQRS
TUV
WXYZ
Book Sending
TEL=
1 49 39 25 25
02 Canon FRANCE
Ex:
• The number registered under that coded speed dialling code is displayed.
• If you enter the wrong code, press Stop/Reset. Then press Coded Dial and enter the correct code.
• NO TEL
appears if no fax number is assigned to the coded speed dialling code you entered.
4-3
Download from Www.Somanuals.com. All Manuals Search And Download.
SB_PC1270D_FG_EN.book Page 4 Monday, February 18, 2002 12:20 PM
Group Dialling
Dial a group of fax numbers registered under a one-touch speed dialling key or coded speed dialling code.
❚ To enter a group registered under a one-touch speed dialling key:
Press the one-touch speed dialling key assigned to the group you wish to fax. (→ p. 4-3)
TEL=GROUP DIAL
03 Canon GROUP 2
Ex:
• The name of the group is displayed.
• If you press the wrong key, press Stop/Reset, then press the correct key.
• NO TEL
appears if no fax number is assigned to the one-touch speed dialling key you pressed.
❚ To enter a group registered under a coded speed dialling code:
Press Coded Dial, then using the numeric keys to enter the two-digit code assigned to the group you wish to fax. (→ p. 4-3)
TEL=GROUP DIAL
21 Canon GROUP 1
Ex:
• The name of the group is displayed.
• If you enter the wrong code, press Stop/Reset. Then press Coded Dial and enter the correct code.
• NO TEL
appears if no fax number is assigned to the coded speed dialling code you entered.
Directory Dialling
Directory dialling allows you to look up the other party’s name and retrieve the number for dialling. This feature is convenient
when you know the other party’s name but cannot recall the One-Touch Speed Dialling key, the code for Coded Speed Dialling,
or Group Dialling where the number is registered.
1
2
Press Directory.
:A
• NO TEL appears if the name of the other party is not registered and the display
_
Ex:
will return to dial entry mode.
Press a numeric key to enter the first letter of the name of the party you are
searching for.
For example, if you want to search for a name that starts with the letter “H”, press
4 (GHI) twice.
3
4
5
Press OK.
• The names of other parties are displayed according to the first letter you entered.
• If there is no name that starts with the letter you entered, other names that start
with the next letter will appear.
Press (–) or (+) to display the other names.
• Pressing (+) will display the names of other parties in alphabetical order.
Pressing (–) will display them in reverse order.
• When you reach the last name, the display will return to the first name.
Press OK.
• The other party’s fax number and name or GROUP DIAL and the group’s name
will appear.
4-4
Download from Www.Somanuals.com. All Manuals Search And Download.
SB_PC1270D_FG_EN.book Page 5 Monday, February 18, 2002 12:20 PM
Sending Methods
■ Memory Sending
The machine begins calling the other party and transmitting the information after all documents are scanned into the memory.
Since the machine is multitasking, you can perform other operations while the machine is sending a fax.
The machine has enough memory to store up to approximately 79 pages* (fewer if the document contains many graphics or
particularly dense text).
* Based on Canon FAX Standard Chart No. 1, standard mode.
• When a large amount of memory is used, MEMORY FULL may be displayed depending on the documents to be sent, and the machine
can neither store the scanned documents in memory nor send them. In this case, print or delete any documents in memory, or select a
lower fax resolution such as STANDARD, then send the documents.
■ Using the ADF
1
2
Press FAX to set to Fax Mode.
FAX 03/12 2001 15:30
4
FaxTel
STANDARD
Ex:
Ex:
Prepare the document and load it face down in the ADF. (→ Reference
MEM IN USE
Guide)
0%
• To adjust the resolution, → p. 4-1.
(Currently used memory)
• To adjust the contrast, → p. 9-4.
DOCUMENT READY
(Standby to scan)
3
4
Dial the other party’s fax number.
TEL=
9057951111
• For dialling methods, → p. 4-2.
Ex:
• If you enter the wrong number, press Stop/Reset, then enter the correct number.
• If you must first dial a digit to get an outside line (“9”, for example), add a pause
after that digit by pressing Redial/Pause.
Press Start to begin scanning for sending.
• The machine begins calling the other party after all documents are scanned into
the memory.
• When you use speed dialling, scanning starts automatically without pressing
Start when the TIME OUT setting is on. (→ p. 9-6)
• To cancel sending once dialling has started, press Stop/Reset then press (–).
(→ p. 4-7)
• You can scan a document up to 356 mm long.
• You can load up to 30 pages in the ADF.
• You can make up to 21 reservations.
4-5
Download from Www.Somanuals.com. All Manuals Search And Download.
SB_PC1270D_FG_EN.book Page 6 Monday, February 18, 2002 12:20 PM
■ Using the Platen Glass
• When documents are loaded in the ADF, the machine will scan them. You need to remove documents from the ADF in advance, in
order to fax from the platen glass.
• You can operate Book Sending, Delete or Clear when the Function key is lit. If the Function key is not lit, press it. However,
you do not need to press Function in step 3 to execute the Book Sending function if BOOK SENDING is programmed in PROGRAM
1-TOUCH KEY. (→ p. 9-4)
1
2
Press FAX to set to Fax Mode.
FAX 03/12 2001 15:30
FaxTel STANDARD
Ex:
Prepare the document and place it face down on the platen glass. (→
Reference Guide)
• To adjust the resolution, → p. 4-1.
• To adjust the contrast, → p. 9-4.
3
4
5
Press Function.
Press Book Sending.
Press (–) or (+) to select the document size.
BOOK TX SCAN SIZE
A4
Ex:
Ex:
6
7
Press OK.
Dial the other party’s fax number.
• For dialling methods, → p. 4-2.
TEL=
9057951111
• If you enter the wrong number, press Delete to delete the last number or press
Clear to delete all the numbers you entered, then enter the correct number.
• If you must first dial a digit to get an outside line (“9”, for example), add a pause
after that digit by pressing Redial/Pause.
8
9
Press Start to begin scanning.
NEXT PAGE
:[START]
FINISH SCAN :[OK]
Set the next document on the platen glass and press Start to begin
scanning.
• Repeat for other documents.
10 After all the documents have been scanned, press OK to begin sending.
• To cancel sending after dialling has started, press Stop/Reset then press (–).
(→ p. 4-7)
• You can scan up to approximately 79 pages* of different documents for memory
sending.
* Based on Canon FAX Standard Chart No. 1, standard mode.
• The Function key will light up by pressing Function to be able to operate
Delete or Clear.
4-6
Download from Www.Somanuals.com. All Manuals Search And Download.
SB_PC1270D_FG_EN.book Page 7 Monday, February 18, 2002 12:20 PM
Cancelling Sending
Cancelling Memory Sending
■ To cancel memory sending while documents are being scanned using the ADF
1
Press Stop/Reset.
• Scanning is cancelled.
■ To cancel memory sending after all documents have been scanned
❚ While documents are being sent:
Press Stop/Reset.
1
2
CANCEL DURING TX/RX?
< YES NO >
• The machine asks you to confirm that you want to cancel.
Press (–) to cancel sending.
• If you change your mind and want to continue sending, press (+).
• The machine prints an ERROR TX REPORT. (→ p. 7-3)
4
❚ While documents are waiting to be sent:
• You can operate Fax Monitor or Delete when the Function key is lit. If the Function key is not lit, press it. However, you do not
need to press Function in step 1 to execute the Fax Monitor function if FAX MONITOR is programmed in PROGRAM 1-TOUCH
KEY. (→ p. 9-4)
1
2
3
Press Function.
Press Fax Monitor.
Use (–) or (+) to select 2.TX RESERVE STATUS.
FAX MONITOR
2.TX RESERVE STATUS
4
Press OK.
--:-- 0013 TX STNDBY
905795 1111
Ex:
5
6
Use (–) or (+) to select the document to be cancelled by checking the
reservation number and the fax number.
Press Delete.
OK TO DELETE?
< YES
• The machine asks you to confirm that you want to delete the document.
NO >
0013
7
Press (–) to cancel sending.
• If you change your mind and want to continue sending, press (+).
TX/RX NO.
ERASING END
Ex:
• You can also cancel sending in Memory Reference. (→ p. 4-16)
4-7
Download from Www.Somanuals.com. All Manuals Search And Download.
SB_PC1270D_FG_EN.book Page 8 Monday, February 18, 2002 12:20 PM
Redialling When the Line is Busy
There are two methods of redialling: Manual redialling and Automatic redialling. This section explains these two methods.
■ Manual Redialling
Press Redial/Pause to dial the last number you dialled with the numeric keys. (This starts redialling regardless of whether
automatic redialling is enabled.)
Cancelling Manual Redialling
To cancel manual redialling, press Stop/Reset.
■ Automatic Redialling
The fax automatically redials after the first attempt at sending fails (e.g. the line is busy).
The number of redialling attempts and the time interval between attempts can be adjusted by changing the settings in the AUTO
REDIAL. Automatic redialling can also be set off and on. (→ p. 9-6)
If all attempts are unsuccessful, the machine cancels the transmission and prints an ERROR TX REPORT. (→ p. 7-3)
Cancelling Automatic Redialling
• If you want to cancel a transmission while the machine is waiting to redial, you will have to delete the document from memory using
Memory Reference. (→ p. 4-16)
1
2
Wait until the machine begins redialling.
Press Stop/Reset.
• The machine asks you to confirm that you want to cancel.
CANCEL DURING TX/RX?
< YES NO >
3
Press (–) to cancel redialling.
• If you change your mind and want to continue redialling, press (+).
• The machine prints an ERROR TX REPORT. (→ p. 7-3)
4-8
Download from Www.Somanuals.com. All Manuals Search And Download.
SB_PC1270D_FG_EN.book Page 9 Monday, February 18, 2002 12:20 PM
Sequential Broadcasting
Sending a Document to More Than One Destination
This feature allows you to scan a document once and send it to several destinations. You can send the document to a maximum
of 122 destinations using a combination of the following dialling methods:
• One-touch speed dialling: up to 12 destinations
• Coded speed dialling: up to 100 destinations
• Regular dialling (using the numeric keys): 10 destinations
You can enter the destinations in any order. (Be sure to press OK after your entry with the numeric keys.)
• If you frequently send documents to the same group of destinations, you can group them and register these numbers for group dialling.
You can register up to 111 fax numbers with group dialling and send the same document to these numbers. (→ p. 3-7)
• The Function key will light up by pressing Function to be able to operate Clear.
1
2
Press FAX to set to Fax Mode.
Prepare the document and load it face down in the ADF.
• If you use the platen glass to send a document → p. 4-6.
• To adjust the resolution, → p. 4-1.
MEM IN USE
4
0%
Ex:
(Currently used memory)
• To adjust the contrast, → p. 9-4.
DOCUMENT READY
(Standby to scan)
3
Enter up to 122 fax numbers using any of the following methods:
❚ One-touch speed dialling:
Press the desired one-touch speed dialling key(s).
TEL=
2 50921
04 Canon ITALIA
Ex:
Ex:
Ex:
❚ Coded speed dialling:
Press Coded Dial, then use the numeric keys to enter the two-digit code. Repeat
for other codes.
TEL=
02 Canon FRANCE
1 49 39 25 25
❚ Regular dialling:
Use the numeric keys to enter the fax number, then press OK.
TEL=
9057951111
• If you enter an incorrect destination, press Clear to delete it.
• You must enter the second fax number within five seconds of entering the first one.
After that, all subsequent fax numbers must be entered within 10 seconds of each
other. If you wait longer than this, the machine automatically begins scanning the
document for sending. If you prefer the machine not to do this, disable the TIME
OUT setting. (→ p. 9-6)
• If you want to review the numbers you entered, use
through the numbers.
(–) or
(+) to scroll
4-9
Download from Www.Somanuals.com. All Manuals Search And Download.
SB_PC1270D_FG_EN.book Page 10 Monday, February 18, 2002 12:20 PM
4
Press Start.
• After the scanning is finished, the machine starts to dial the number.
• The machine will first send the document to the one-touch speed dialling
destinations, then the coded speed dialling destinations, and finally to the
destination dialled using regular dialling.
• If you prefer the machine never to scan a document automatically after a few
seconds, disable the TIME OUT setting. (→ p. 9-6)
• To cancel sending, press Stop/Reset then press (–). Sending to all
destinations specified in step 3 will be cancelled. You cannot cancel just one
destination.
After cancelling, the machine will print a MULTI TX/RX REPORT. (→ p. 7-4)
• If a number is busy, the machine will continue sending to the other destinations and
then redial the number that was busy.
• If the machine’s memory becomes full while scanning your document, MEMORY
FULL will appear in the LCD and the document being scanned stops in the ADF.
Press OK to make the document come out automatically. If this happens, divide the
documents into several sections and send each section separately.
4-10
Download from Www.Somanuals.com. All Manuals Search And Download.
SB_PC1270D_FG_EN.book Page 11 Monday, February 18, 2002 12:20 PM
Delayed Sending
You can use your machine to send faxes at a preset time. This feature is called Delayed sending or Timer sending. By using this
feature, you can take advantage of lower long distance rates at night, for example.
You can set up to 122 destinations, and up to 21 reservations of delayed sending.
• You can perform other tasks even when you have set the machine for delayed sending.
• You can operate Book Sending, Delayed Transmission or Clear when the Function key is lit. If the Function key is not lit,
press it. However, you do not need to press Function in step 1 or 2 to execute the Delayed Transmission function or Book Sending
function if DELAYED TX or BOOK SENDING is programmed in PROGRAM 1-TOUCH KEY. (→ p. 9-4)
1
Prepare the document and place it on the platen glass or load it face down
in the ADF.
• When using the platen glass, press Function and select the document size with
(–) or
(+). (→ p. 4-6) In this case, you do not need to press Function in step 2.
2
3
4
Press Function.
Press Delayed Transmission.
4
Use the numeric keys to enter the reservation time to send faxes.
DELAYED TX
TX TIME SETTNG 15:30
Ex:
5
Press OK.
DELAYED TX
SELECT LOCATIONS
TEL=
6
Enter a destination using a one-touch speed dialling key, coded speed
dialling keys, Redial/Pause key or the numeric keys.
• You can use the one-touch speed dialling key when the Function key is not lit. If
the Function key is lit, press it.
• If you enter an incorrect destination, press Clear to delete it.
7
Press Start to begin scanning.
• When you use speed dialling, scanning starts automatically without pressing
Start when the TIME OUT setting is on. (→ p. 9-6)
• When the time you set in step 4 comes, the machine will begin sending faxes.
4-11
Download from Www.Somanuals.com. All Manuals Search And Download.
SB_PC1270D_FG_EN.book Page 12 Monday, February 18, 2002 12:20 PM
Confirming Transmission Status and Sending Reservation
You can check the status of sending or receiving fax, or sending reservation.
• You do not need to press Function in step 1 to execute the Fax Monitor function if FAX MONITOR is programmed in PROGRAM 1-
TOUCH KEY. (→ p. 9-4)
■ Confirming Transmission Status
The sending or receiving status can be confirmed using the following method:
1
2
Press Function while In Use/Memory is flashing.
Press Fax Monitor.
FAX MONITOR
1.RX/TX STATUS
3
Press OK.
16:50 0056 TX
12345
Ex:
• To return to standby display, press Stop/Reset.
• If you perform the procedure above when the machine is not sending or receiving
faxes, NO CURRENT RX/TX JOB will appear, and the display will return to the
display shown in step 2.
• The transaction number, TX/RX NO. means the following:
– 0001 to 4999: A sent document;
– 5001 to 9999: A received document.
■ Confirming Sending Reservation
Sending reservation or checking if there is a document being scheduled to be sent can be confirmed using the following method:
1
2
Press Function.
Press Fax Monitor.
FAX MONITOR
1.RX/TX STATUS
3
4
Press (–) or (+), to select 2.TX RESERVE STATUS.
FAX MONITOR
2.TX RESERVE STATUS
Press OK.
16:00 0056 TX STNDBY
• The sending reservation can be confirmed by checking the sending time, TX/RX
905 795 1111
Ex:
Ex:
NO. or fax number.
5
Press (–) or (+) to confirm the sending reservation.
17:00 0058 TX STNDBY
20 545 8584
• To return to standby display, press Stop/Reset.
• If you perform the procedure above when there is no sending reservation, NO
DOC. STORED will appear, and the display will return to the display shown in step
3.
• You can also check the reservations by printing out the DOCUMENT MEMORY
LIST. (→ p. 4-13)
4-12
Download from Www.Somanuals.com. All Manuals Search And Download.
SB_PC1270D_FG_EN.book Page 13 Monday, February 18, 2002 12:20 PM
Documents Stored in Memory
• If there are no documents stored in memory, the machine will return to standby mode when you select Memory Reference.
• You do not need to press Function in step 1 to execute the Memory Reference function if MEMORY REFERENCE is programmed in
PROGRAM 1-TOUCH KEY. (→ p. 9-4)
■ Printing a List of Documents in Memory
The machine can print a list of documents stored in memory, along with the transaction number (TX/RX NO.) of each
document.
1
2
Press Function.
Press Memory Reference.
MEMORY REFERENCE
1.DOC. MEMORY LIST
3
Press OK.
4
• The machine prints the DOCUMENT MEMORY LIST and returns to standby
mode.
• Once you know the transaction number of a document stored in memory, you can
print it or delete it. (→ pp. 4-15, 4-16)
03/12 2001 17:15 FAX 123 4567
CANON
001
✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱
✱✱✱ DOCUMENT MEMORY LIST ✱✱✱
✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱
TX/RX NO
0046
MODE
DELAYED TX
DELAYED TX
DEL SQ BDCST
DESTINATION TEL/ID
01] Canon TOKYO
04] Canon ITALIA
PGS.
SET TIME
ST. TIME
14:00
[
[
[
[
[
3
2
1
03/12 16:30
03/12 16:37
03/12 16:42
0047
14:05
14:07
14:07
14:10
0048
02] Canon FRANCE
01] Canon CANADA
03] Canon GROUP 2
0049
DEL SQ BDCST
1
03/12 16:55
4-13
Download from Www.Somanuals.com. All Manuals Search And Download.
SB_PC1270D_FG_EN.book Page 14 Monday, February 18, 2002 12:20 PM
■ Resending a Document in Memory
You can resend documents that are stored in memory. The machine stores faxes that are received but not printed because paper
or toner has run out, a paper jam has occurred, or documents have not been transmitted due to a transmission error.
You can send such faxes to another fax machine to be printed.
1
2
Press Function.
Press Memory Reference.
MEMORY REFERENCE
1.DOC. MEMORY LIST
3
Use (–) or (+) to select 4.RESEND DOCUMENT.
MEMORY REFERENCE
4.RESEND DOCUMENT
• The sending error document also can be resent using 2.MEMORY RETRANSMT.
4
5
6
Press OK.
RESEND DOCUMENT
TX/RX NO.
0051
Ex:
Ex:
Use (–) or (+) to select the transaction number (TX/RX NO.) of the
document you want to send again.
RESEND DOCUMENT
TX/RX NO.
0053
Press OK.
RESEND DOCUMENT
SELECT LOCATIONS
TEL=
7
8
Enter the fax number.
Press OK.
• The machine begins sending.
4-14
Download from Www.Somanuals.com. All Manuals Search And Download.
SB_PC1270D_FG_EN.book Page 15 Monday, February 18, 2002 12:20 PM
■ Printing a Document in Memory
1
Press Function.
2
Press Memory Reference.
MEMORY REFERENCE
1.DOC. MEMORY LIST
3
4
5
Use (–) or (+) to select 3.PRINT DOCUMENT.
Press OK.
MEMORY REFERENCE
3.PRINT DOCUMENT
PRINT DOCUMENT
TX/RX NO.
0001
Ex:
Ex:
Use (–) or (+) to select the transaction number (TX/RX NO.) of the
document you want to print.
• You can enter the transaction number using the numeric keys.
PRINT DOCUMENT
TX/RX NO.
0003
6
7
Press OK.
PRINT 1ST PAGE ONLY?
< YES NO >
4
Press (–) to print the first page only, or press (+) to print all pages of
the document.
• The machine prints the document.
• Pressing
(–) prints the first page when sending (this is the last scanned page),
not the first page when scanning with the ADF.
8
To continue printing other documents in memory, repeat the procedures
from step 5.
– or –
Press Stop/Reset to return to standby display.
4-15
Download from Www.Somanuals.com. All Manuals Search And Download.
SB_PC1270D_FG_EN.book Page 16 Monday, February 18, 2002 12:20 PM
■ Deleting a Document from Memory
1
2
3
Press Function.
Press Memory Reference.
Use (–) or (+) to select 5.DELETE DOCUMENT.
MEMORY REFERENCE
5.DELETE DOCUMENT
4
5
Press OK.
DELETE DOCUMENT
TX/RX NO.
0001
Ex:
Ex:
Use (–) or (+) to select the transaction number (TX/RX NO.) of the
document you want to delete.
• You can enter the transaction number using the numeric keys.
DELETE DOCUMENT
TX/RX NO.
0004
NO >
6
7
Press OK.
OK TO DELETE?
< YES
• The machine asks you to confirm that you want to delete the document.
Press (–) to delete the document.
• The machine deletes the document.
• If you change your mind and want to keep the document in memory, press (+).
8
To continue deleting other documents in memory, repeat the procedures
from step 5.
– or –
Press Stop/Reset to return to standby display.
4-16
Download from Www.Somanuals.com. All Manuals Search And Download.
SB_PC1270D_FG_EN.book Page 1 Monday, February 18, 2002 12:20 PM
Chapter 5
Receiving Faxes
Different Ways to Receive a Fax
The machine provides you with several modes for receiving faxes. Once you have decided which mode is suitable for your needs,
set the mode as described in the Quick Start Guide. You can change the mode when the machine is in standby mode. To
determine which mode best suits your requirements, refer to the table below:
Receive Mode
FaxTel*
Main Use
Fax/Tel
Operation
Requirements
Automatically switches between fax calls Telephone connected to the machine.
and voice calls. Receives faxes
automatically and rings for voice calls. To
set the details, → pp. 5-3, 5-4.
FaxOnly
Manual
Fax
Tel
Machine answers all calls as fax calls. It
receives faxes automatically and
disconnects voice calls.
Separate telephone line for fax use
only.
5
Machine rings for every call, whether it is Telephone connected to the machine.
a fax call or a voice call. For a fax call, you
have to manually activate reception of the
fax.
AnsMode
Fax/Tel
Receives faxes automatically and routes
voice calls to the answering machine.
Answering machine connected to the
machine.
*
Factory default setting
You can confirm which receive mode is set by checking the standby display. The receive mode is displayed in the lower left of
the LCD.
FAX 03/12 2001 15:30
FaxTel
STANDARD
Ex:
5-1
Download from Www.Somanuals.com. All Manuals Search And Download.
SB_PC1270D_FG_EN.book Page 2 Monday, February 18, 2002 12:20 PM
Setting the Receive Mode
The setting of the receive mode can be changed if necessary.
1
Press Receive Mode until the mode you want appears.
• You can select from the following:
– FaxTel* :
RECEIVE MODE
Manual
Ex:
when a telephone is connected to the machine, the machine automatically
switches between fax calls and voice calls.
– FaxOnly :
if you use your machine to receive only faxes.
– Manual :
when a telephone is connected to the machine, you can receive faxes by pressing
Start before replacing the handset on the telephone.
– AnsMode :
if you want to receive faxes automatically and route voice calls to an answering
machine.
*
You can set details for the FaxTel mode. (→ pp. 5-3, 5-4)
2
Press OK.
FAX 03/12 2001 15:30
The selected receive mode is set and the machine returns to standby mode. The
current date and the selected receive mode are displayed.
Manual
STANDARD
Ex:
• The machine does not ring when it receives a fax in FaxOnly. If you want to be
alerted when a fax call is received, connect a telephone to the machine, and enable
the INCOMING RING setting.
• When an answering machine or a telephone with an answering machine is
connected to your machine, select AnsMode. (→ Quick Start Guide)
• Follow these guidelines when using the machine with an answering machine:
– Set the answering machine to answer on the first or second ring.
– When recording the outgoing message on the answering machine, the entire
message must be no longer than 15 seconds.
Ex: “Hello, I can’t answer the phone right now, but please leave a message after
the beep. I’ll return your call as soon as possible.”
5-2
Download from Www.Somanuals.com. All Manuals Search And Download.
SB_PC1270D_FG_EN.book Page 3 Monday, February 18, 2002 12:20 PM
■ Setting the Options for FaxTel Mode
When selecting FaxTel mode, the following options can be set.
• Adjust the time the machine takes to check whether a call is from a fax machine or a telephone (RING START TIME setting).
• Adjust the length of time the machine rings when the call is a voice call (F/T RING TIME setting).
• Set whether the machine switches to receive mode after the ring time set in F/T RING TIME has elapsed (F/T SWITCH
ACTION setting).
• The default settings and selectable settings vary depending on the current country selection.
■ What Happens When FaxTel Mode is Selected
Type of call
Telephone
Telephone
Fax
Fax
Fax
Fax
Sending document
manually
Sending document
automatically
Telephone charges
begin for the caller.
The machine answers without ringing.
5
The machine listens for the fax tone.
The fax tone is
detected.
The document is
received automatically.
RING START TIME
The fax tone is detected
and the machine
switches to receive
mode.
The fax tone is not detected.
The machine starts ringing.
Pick up the handset to
talk.
F/T RING TIME
If you do not pick up the handset.
F/T SWITCH ACTION
Choose between:
RECEIVE and DISCONNECT.
DISCONNECT
The machine
disconnects the call.
RECEIVE
Not all fax machines are capable of sending a fax tone.
For those cases if you set the F/T SWITCH ACTION to
RECEIVE, the machine switches to receive mode
automatically and starts receiving the document. If no
document comes in, it disconnects the call after
approximately 40 seconds.
5-3
Download from Www.Somanuals.com. All Manuals Search And Download.
SB_PC1270D_FG_EN.book Page 4 Monday, February 18, 2002 12:20 PM
1
2
Press Additional Functions.
Use (–) or (+) to select 3.FAX SETTINGS.
ADDITIONAL FUNCTIONS
3.FAX SETTINGS
3
4
5
6
7
Press OK.
FAX SETTINGS
1.USER SETTINGS
Use (–) or (+) to select 4.RX SETTINGS.
Press OK.
FAX SETTINGS
4.RX SETTINGS
RX SETTINGS
1.ECM RX
Use (–) or (+) to select 2.FAX/TEL OPT.SET.
Press OK twice.
RX SETTINGS
2.FAX/TEL OPT.SET
FAX/TEL OPT. SET
1.RING START TIME
RING START TIME
08SEC
Ex:
Ex:
8
9
Use (–) or (+) to set the time the machine waits before ringing when
it receives a call.
RING START TIME
09SEC
• You can use the numeric keys instead of using (–) or (+) to set the time.
Press OK twice.
FAX/TEL OPT. SET
2.F/T RING TIME
F/T RING TIME
022SEC
Ex:
Ex:
10 Use (–) or (+) to set the time the machine rings while waiting for
F/T RING TIME
030SEC
someone to pick up the handset.
11 Press OK twice.
FAX/TEL OPT. SET
3.F/T SWITCH ACTION
F/T SWITCH ACTION
RECEIVE
Ex:
Ex:
12 Use (–) or (+) to select RECEIVE or DISCONNECT.
• This setting tells the machine what to do if no one picks up the handset within the
specified ring time set in step 10.
F/T SWITCH ACTION
DISCONNECT
13 Press OK.
RX SETTINGS
3.INCOMING RING
14 Press Stop/Reset to return to standby display.
• The default settings and selectable settings vary depending on the current country selection.
5-4
Download from Www.Somanuals.com. All Manuals Search And Download.
SB_PC1270D_FG_EN.book Page 5 Monday, February 18, 2002 12:20 PM
Receiving Faxes Manually
In Manual mode, if you connect a telephone to your machine, you can receive voice calls as well as manually activate reception
of faxes. You can activate reception from the machine or from the telephone connected to the machine (this is called Remote
receiving).
• For this mode, you need to connect a telephone to your machine. (→ Quick Start Guide)
• Make sure there are no documents in the ADF.
• Make sure the REMOTE RX setting is enabled. (→ p. 9-7)
• If your telephone line uses rotary pulse and the telephone connected to the machine cannot be switched to tone dialling, you cannot
activate Remote receiving.
1
Make sure Manual is displayed in the LCD.
• To set Manual, → p. 5-2.
FAX 03/12 2001 15:30
Manual STANDARD
Ex:
2
3
4
Make sure you have connected a telephone to the machine.
When you hear the telephone ring, pick up the handset.
❚ If you hear a person’s voice:
Start your conversation. If the caller wants to send a fax after talking to you, ask
them to press Start on their fax machine.
When you hear a slow beep, press Start on the machine to begin receiving the fax.
Hang up the handset.
5
❚ If you hear a slow beep tone or silence:
Someone is trying to send you a fax.
If the telephone is close to your machine, press Start on the machine to begin
receiving the fax. Hang up the handset.
• When no paper is loaded in the cassette, the LCD displays SUPPLY REC.
PAPER. When paper is loaded, the machine automatically resumes printing.
• If the telephone is located away from your machine, dial 25 (the remote receiving
ID) on your telephone and hang up. When your telephone line uses rotary pulse,
switch to tone dialling on your telephone before dialling 25 (the remote receiving
ID).
• You can change the number for the remote receiving ID, with a combination of two
characters using 0 to 9,
and , or disable remote receiving. (→ p. 9-7)
• If you have an answering machine connected to your machine that can carry out
remote-control operations (controlling your answering machine from a remote
telephone), the security code for this function may be the same as the remote
receiving ID. If so, make sure you change the machine’s remote receiving ID to
make it distinct from the answering machine’s security code. (→ p. 9-7)
• The machine will beep and HANG UP PHONE will be displayed if the handset is
not hung up properly. Make sure the handset is seated properly in its cradle. If you
do not want the machine to beep, disable the OFFHOOK ALARM setting. (→ p. 9-5)
5-5
Download from Www.Somanuals.com. All Manuals Search And Download.
SB_PC1270D_FG_EN.book Page 6 Monday, February 18, 2002 12:20 PM
Registering a Password and Subaddress for Polling
The polling feature allows you to request a document to be faxed to you from another fax machine. The sender only needs to
make sure that the document is on his fax machine and ready to be sent.
When this machine polls the sender’s machine, the document is sent automatically.
• You can register a password and subaddress with a one-touch speed dialling key or coded speed dialling code.
• You must know if the other party’s fax is holding the document under both a password and subaddress or only a password or
subaddress. You must also know the password and subaddress so that you can enter them on your fax. If you do not know the password
and subaddress, contact the other party.
• The Function key will light up by pressing Function to be able to operate Space, Delete or Clear.
1
2
Press Additional Functions.
Use (–) or (+) to select 4.ADD. REGISTRATION.
ADDITIONAL FUNCTIONS
4.ADD. REGISTRATION
3
4
5
6
7
8
9
Press OK.
ADD. REGISTRATION
1.1-TOUCH SPD DIAL
Use (–) or (+) to select 1.1-TOUCH SPD DIAL or 2.CODED SPD
DIAL.
ADD. REGISTRATION
1.1-TOUCH SPD DIAL
Ex:
Ex:
Ex:
Press OK.
1-TOUCH SPD DIAL
01=
905795 1111
Use (–) or (+) to select the one-touch speed dialling number or coded
speed dialling code.
1-TOUCH SPD DIAL
02=
81 773 3115
Press OK.
1-TOUCH SPD DIAL
1.TEL NUMBER ENTRY
Use (–) or (+) to select 3.OPTIONAL SETTING.
Press OK.
1-TOUCH SPD DIAL
3.OPTIONAL SETTING
OPTIONAL SETTING
OFF
Ex:
10 Use (–) or (+) to select ON.
11 Press OK.
OPTIONAL SETTING
ON
OPTIONAL SETTING
1.TX TIME SETTING
12 Use (–) or (+) to select 2.TX TYPE.
13 Press OK.
OPTIONAL SETTING
2.TX TYPE
TX TYPE
SUBADDRESS TX
POLLING RX
Ex:
14 Use (–) or (+) to select POLLING RX.
TX TYPE
5-6
Download from Www.Somanuals.com. All Manuals Search And Download.
SB_PC1270D_FG_EN.book Page 7 Monday, February 18, 2002 12:20 PM
15 Press OK twice.
POLLING RX
1.PASSWORD
PASSWORD
Ex:
Ex:
16 Enter a password.
PASSWORD
• You can enter a password up to 20 digits long using the numeric keys,
,
or
12345
Space.
• Be sure to enter the password of the other party correctly, taking into account the
position of spaces.
• If you make a mistake, press Delete to delete the last character or press Clear to
delete all the characters you entered.
17 Press OK twice.
SUBADDRESS
SUBADDRESS
Ex:
Ex:
18 Enter a subaddress.
• You can enter a subaddress up to 20 digits long using the numeric keys,
,
or
123456789012
Space.
• Be sure to enter the subaddress of the other party correctly, taking into account
the position of spaces.
• If you make a mistake, press Delete to delete the last character or press Clear to
delete all the characters you entered.
5
19 Press OK.
1-TOUCH SPD DIAL
03=GROUP DIAL
Ex:
20 To continue registering other passwords and subaddresses, press
Additional Functions then repeat the procedure from step 4.
– or –
Press Stop/Reset to return to standby display.
Cancelling Polling Receiving
To cancel polling receiving, follow the same procedure as for cancelling receiving. (→ p. 5-8)
5-7
Download from Www.Somanuals.com. All Manuals Search And Download.
SB_PC1270D_FG_EN.book Page 8 Monday, February 18, 2002 12:20 PM
Receiving While Performing Other Tasks
Since the machine is a multitasking device, it can receive faxes and voice calls while you are performing other tasks.
If you receive a fax while you are performing certain tasks, the machine stores the incoming fax in memory. Then, as soon as
you finish your task, the machine automatically prints the fax.
• If you copy or print a document from the PC, printing of the received fax is suspended and resumed after copying or printing from the
PC is finished.
Receiving Faxes in Memory When a Problem Occurs
If the machine encounters a problem when it is receiving a fax, the machine automatically stores the unprinted pages of the fax
in memory, and the LCD displays RECEIVED IN MEMORY as well as one or more messages. When the problem is cleared,
the machine automatically prints the fax which was stored in memory. For an explanation of the message(s) and details on the
action to take, → p. 8-1.
• The machine memory can store up to approximately 79 pages.*
• Once the pages are printed, they are deleted from memory.
• If the memory becomes full, you will not be able to receive the remaining pages. Contact the other party and ask them to resend the
remainder of the fax.
*
Based on Canon Fax Standard Chart No. 1, standard mode.
Cancelling Receiving
Follow this procedure if you want to stop receiving a fax before reception is completed:
1
2
Press Stop/Reset.
CANCEL DURING TX/RX?
< YES NO >
• The machine asks you to confirm that you want to cancel.
Press (–) to cancel receiving.
• If you change your mind and want to continue receiving, press (+).
5-8
Download from Www.Somanuals.com. All Manuals Search And Download.
SB_PC1270D_FG_EN.book Page 1 Monday, February 18, 2002 12:20 PM
Chapter 6
Special Features
Special Dialling
This section explains special dialling features, such as dialling through a switchboard, dialling an overseas number, and
switching temporarily to tone dialling.
■ Dialling an Overseas Number (With Pauses)
When you dial or register an overseas number, you may need to insert a pause within and/or after the number. The length and
location of the pause depends on the telephone system of your country.
1
2
Press FAX to set to Fax Mode.
FAX 03/12 2001 15:30
FaxTel
STANDARD
Ex:
Ex:
Prepare the document and load it facing down into the ADF.
• If you use the platen glass to send a document, → p. 4-6.
MEM IN USE
0%
(Currently used memory)
DOCUMENT READY
6
(Standby to scan)
3
4
Use the numeric keys to dial the international access code.
• If you enter the wrong number, press Stop/Reset, then enter the correct number.
• For details on international access codes, contact your local telephone company.
TEL=
00
Ex:
Ex:
If necessary, press Redial/Pause to enter a two-second* pause (p).
• For a longer pause, press Redial/Pause again for another two-second* pause.
Alternatively, you can change the length of the pause. (→ p. 9-5)
TEL=
00P
* The pause length varies depending on the current country selection.
5
Use the numeric keys to dial the country code, the area code, and the fax/
telephone number of the other party.
TEL=
TEL=
00p81123
Ex:
Ex:
• If you enter the wrong number, press Stop/Reset and start again from step 3.
6
7
If necessary, press Redial/Pause to enter a pause at the end of a number.
• A pause at the end of a number (P) is fixed to 10 seconds.
00p81123P
Press Start to begin scanning for sending.
• To cancel sending after dialling has started, press Stop/Reset then (–). (→ p.
4-7)
• To take advantage of the speed dialling features of your machine, register
frequently used overseas numbers for one-touch or coded speed dialling. (→ pp. 3-
2, 3-4)
6-1
Download from Www.Somanuals.com. All Manuals Search And Download.
SB_PC1270D_FG_EN.book Page 2 Monday, February 18, 2002 12:20 PM
■ Switching Temporarily to Tone Dialling
Many information services for banks, airline reservations, hotel reservations, etc., require tone dialling for their services. If your
machine is connected to a rotary pulse line, follow this procedure to set the machine temporarily for tone dialling:
• The Function key will light up by pressing Function to be able to operate Tone/+.
1
Press FAX to set to Fax Mode.
FAX 03/12 2001 15:30
FaxTel
STANDARD
Ex:
2
3
Pick up the handset of your telephone.
Enter a destination using the numeric keys on your telephone or using a
one-touch speed dialling key, coded speed dialling codes, Redial/Pause
key or the numeric keys on the machine.
4
5
When the recorded message of the information service answers, press
Tone/+ to switch to tone dialling.
TEL=
TEL=
T
Ex:
Ex:
• When Tone/+ is pressed, T is displayed in the LCD.
• If your telephone line uses tone dialling, go to the next step.
Use the numeric keys on the machine to enter the numbers requested by
the information service.
• Numbers entered after pressing Tone/+ will be dialled using tone dialling.
• After pressing Tone/+, you cannot use the numeric keys on the telephone. Use
the numeric keys on the machine.
T34
6
7
If you want to receive faxes, press Start.
Hang up to disconnect the call.
• Tone dialling is cancelled when you disconnect the call.
6-2
Download from Www.Somanuals.com. All Manuals Search And Download.
SB_PC1270D_FG_EN.book Page 3 Monday, February 18, 2002 12:20 PM
■ Confirming a Dial Tone*
* This feature is only available for some countries.
This feature allows you to set your machine to listen for and detect a dial tone in the middle of a fax/telephone number before
dialling the rest of the number. This is called Dial tone detection.
Follow this procedure for dial tone detection during regular dialling or when registering a number for speed dialling:
• The Function key will light up by pressing Function to be able to operate D.T., Delete or Clear.
1
When you come to a step that requires you to enter the fax/telephone
number, use the numeric keys to enter the number up to where dial tone
detection is required.
TEL=
345
Ex:
2
3
Press D.T. for dial tone detection.
TEL=
TEL=
345.
• A small dot indicates where the machine will wait for the dial tone.
Ex:
Ex:
Continue entering the rest of the fax/telephone number with the numeric
keys.
• If you enter the wrong number, press Delete to delete the last number or press
Clear to delete all the numbers you entered, then start again from step 1.
345.1234
4
Continue with the operation you are performing.
■ Dialling Through a Switchboard
6
For details on dialling through a switchboard, → p. 2-7.
6-3
Download from Www.Somanuals.com. All Manuals Search And Download.
SB_PC1270D_FG_EN.book Page 4 Monday, February 18, 2002 12:20 PM
Restricting Use of Your Machine
By enabling this feature, you can prevent unauthorised use of your machine to make calls and send faxes.
Enabling Restriction of Your Machine
Follow this procedure to enable restriction of your machine:
1
2
Press Additional Functions.
Use (–) or (+) to select 3.FAX SETTINGS.
ADDITIONAL FUNCTIONS
3.FAX SETTINGS
3
4
5
6
7
8
9
Press OK.
FAX SETTINGS
1.USER SETTINGS
Use (–) or (+) to select 6.SYSTEM SETTINGS.
Press OK.
FAX SETTINGS
6.SYSTEM SETTINGS
SYSTEM SETTINGS
1.FAX DEFAULT
Use (–) or (+) to select 2.LOCK PHONE.
Press OK.
SYSTEM SETTINGS
2.LOCK PHONE
LOCK PHONE
OFF
Ex:
Use (–) or (+) to select ON.
LOCK PHONE
ON
Press OK.
SYSTEM SETTINGS
3.COUNTRY SELECT
• The display contents differs depending on the country.
10 Press Stop/Reset to return to standby display.
Restriction of your machine is now enabled. No one can make calls or send faxes.
(This setting does not restrict incoming calls or faxes.)
Cancelling Restriction of Your Machine
Follow this procedure to cancel restriction of your machine:
1
2
Follow steps 1 to 7 of “Enabling Restriction of Your Machine.”
Use (–) or (+) to select OFF.
LOCK PHONE
OFF
3
4
Press OK.
SYSTEM SETTINGS
3.COUNTRY SELECT
• The display contents differs depending on the country.
Press Stop/Reset to return to standby display.
Restriction of your machine is now disabled. Anyone can make calls or send faxes.
6-4
Download from Www.Somanuals.com. All Manuals Search And Download.
SB_PC1270D_FG_EN.book Page 1 Monday, February 18, 2002 12:20 PM
Chapter 7
Reports and Lists
Summary of Reports and Lists
The table below shows the reports and lists that can be printed from your machine. Refer to the pages indicated for more details.
• Make sure that A4-size paper is loaded in the cassette. If a different paper size is loaded, the report or list cannot be printed. Also, you
cannot use the multi-purpose tray for printing the report or list.
Report or List
Description
Details
USER’S DATA LIST
Lists the current settings of your machine and the registered sender
information.
p. 2-6
p. 7-2
ACTIVITY REPORT
Shows recent facsimile transactions performed by your machine.
You can enable or disable automatic printing of this report after every 20
transactions. You can also manually set the machine to print it.
TX (Transmission) REPORT Prints after transmission of a document.
You can enable or disable this feature, or set the machine to print a report
p. 7-3
only when an error occurs.
You can also set the machine to print the first page of the document under
the transmission report to remind you of the contents of the document.
RX (Reception) REPORT
Prints after reception of a document. You can enable or disable this feature, p. 7-4
or set the machine to print a report only when an error occurs.
7
DOCUMENT MEMORY
LIST
Lists the documents currently stored in the machine’s memory.
p. 4-13
1-TOUCH LIST/
1-TOUCH (DETAIL)
Lists the numbers and names registered under one-touch speed dialling
keys.
pp. 3-9, 3-10
pp. 3-10, 3-11
CODED DIAL LIST/
CODED (DETAIL)
Lists the numbers and names registered under coded speed dialling codes.
GROUP DIAL LIST
Lists groups registered under one-touch speed dialling keys and coded speed p. 3-11
dialling codes.
7-1
Download from Www.Somanuals.com. All Manuals Search And Download.
07_EN.fm Page 2 Tuesday, February 19, 2002 11:03 AM
ACTIVITY REPORT
The machine is factory-set to automatically print an ACTIVITY REPORT after every 20 transactions. If you want to print an
ACTIVITY REPORT before it is automatically printed, follow this procedure:
• If you prefer the machine not to print an ACTIVITY REPORT after every 20 transactions, set ACTIVITY REPORT to OFF. (→ p.
9-5)
• You do not need to press Function in step 1 to execute the Report function if REPORT is programmed in PROGRAM 1-TOUCH KEY.
(→ p. 9-4)
1
2
3
Press Function.
Press Report.
Use (–) or (+) to select 1.ACTIVITY REPORT.
REPORT
1.ACTIVITY REPORT
4
Press OK.
• The machine prints an ACTIVITY REPORT and returns to standby mode.
Transactions in an ACTIVITY REPORT are listed chronologically.
03/12 2001 17:28 FAX 123 4567
CANON
001
✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱
✱✱✱ ACTIVITY REPORT ✱✱✱
✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱
ST. TIME
DESTINATION TEL/ID
905 795 1111
905 795 1111
Canon TOKYO
NO.
MODE
AUTO RX
PGS.
RESULT
OK
03/12 15:10
03/12 15:14
03/12 15:22
03/12 15:24
03/12 16:10
03/12 16:16
03/12 16:27
03/12 16:30
03/12 16:53
03/12 17:08
5001
5002
0001
0001
5003
5004
0002
0003
5005
0004
ECM
ECM
ECM
ECM
ECM
ECM
ECM
ECM
ECM
1
1
3
3
1
4
1
1
1
3
00’33
00’24
01’18
01’18
00’18
00’59
01’20
04’12
01’16
00’51
STOP
00’01
0018
AUTO RX
OK
OK
OK
OK
OK
OK
OK
OK
NG
3
03 3758 2111
SEQ. B’CAST
SEQ. B’CAST
AUTO RX
Canon AUSTRALIA 2 887 0166
905 795 1111
2 887 0166
AUTO RX
Canon EUROPE
Canon EUROPE
03 3758 2111
20 545 8545
20 545 8545
TRANSMIT
TRANSMIT
AUTO RX
Canon AUSTRALIA 2 887 0166
TRANSMIT
03/12 17:20
CANON OPTICS 1 432 2060
0005
TRANSMIT
0
NG
0
TRANSACTION (TX/RX) NUMBER
TRANSACTION MODE
INDICATES AN
ENTRY THAT HAS
APPEARED ON A
PREVIOUS REPORT.
ERROR CORRECTION MODE TRANSACTION
ERROR PAGE*
ERROR CODE (→ p. 8-2)
Stop/Reset WAS PRESSED DURING TRANSACTION
TRANSACTION DURATION
* The number of pages that have been printed and the number of pages indicated on the report are not the same.
7-2
Download from Www.Somanuals.com. All Manuals Search And Download.
SB_PC1270D_FG_EN.book Page 3 Monday, February 18, 2002 12:20 PM
TX (Transmission) REPORT
The machine is factory-set to print a TX (transmission) REPORT only when an error occurs during sending. To change this
setting, → p. 9-5.
If you set the machine to print a report, a TX REPORT or an ERROR TX REPORT, similar to the ones below, will be printed
depending on the setting you select.
03/12 2001 17:47 FAX 123 4567
CANON
001
✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱
✱✱✱ TX REPORT ✱✱✱
✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱
TRANSMISSION OK
TX/RX NO
0003
DESTINATION TEL
1 432 2060
03/12 2001 17:21 FAX 123 4567
CANON
001
✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱
✱✱✱ ERROR TX REPORT ✱✱✱
✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱
TX FUNCTION WAS NOT COMPLETED
TX/RX NO
0004
20 545 8545
DESTINATION TEL
DESTINATION ID
ST. TIME
Canon EUROPE
03/12 17:21
00’18
7
TIME USE
PAGES SENT
RESULT
1
N
0018 BUSY/NO SIGNAL
•
THE SLEREXE COMPANY LIMITED
SAPORS LANE·BOOLE·DORSET·BH25 8ER
TELEPHONE BOOLE (945 13) 51617 - FAX 1234567
OUR Ref. 350/PJC/EAC
December 3, 2001
Dr. P.N. Cundall,
Mining Suerveys Ltd.,
Holroyd Road
Reading
Berks
OK: TRANSMISSION SUCCESFULL
NG: SOME OR NO PAGES SENT
NUMBER OF PAGES SENT
TRANSMISSION DURATION
TRANSMISSION TIME
IF YOU ENABLE THE REPORT WITH TX IMAGE
SETTING (→ p. 9-5), THE FIRST PAGE OF THE
DOCUMENT WILL PRINT ON THE REPORT TO
REMIND YOU OF THE CONTENTS OF THE
DOCUMENT.
7-3
Download from Www.Somanuals.com. All Manuals Search And Download.
SB_PC1270D_FG_EN.book Page 4 Monday, February 18, 2002 12:20 PM
■ MULTI TX/RX (Transaction) REPORT
If the transmission was a sequential broadcast, a MULTI TX/RX (transaction) REPORT, similar to the one below, will be
printed.
03/12 2001 18:16 FAX 123 4567
CANON
001
✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱
✱✱✱ MULTI TX/RX REPORT ✱✱✱
✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱
TX/RX NO
0054
1
PGS.
TX/RX INCOMPLETE
TRANSACTION OK
______
[
[
[
00] 2131 1250
Canon DEUTSCH.
Canon FRANCE
Canon CANADA
02] 1 49 39 25 25
01] 905 795 1111
ERROR INFORMATION
______
RX (Reception) REPORT
The machine is factory-set not to print an RX (reception) REPORT even if an error occurs during reception. To change this
setting, → p. 9-5.
If you set the machine to print a report, an RX REPORT, similar to the one below, will be printed.
03/12 2001 17:52 FAX 123 4567
CANON
001
✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱
✱✱✱ RX REPORT ✱✱✱
✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱
RECEPTION OK
TX/RX NO
5004
DESTINATION TEL
DESTINATION ID
ST. TIME
905 795 1111
Canon CANADA
03/12 17:52
TIME USE
01’59
4
PGS.
RESULT
OK
OK: RECEPTION SUCCESFULL
NG: SOME OR NO PAGES RECEIVED
NUMBER OF PAGES RECEIVED
RECEPTION DURATION
RECEPTION TIME
7-4
Download from Www.Somanuals.com. All Manuals Search And Download.
08_EN.fm Page 1 Tuesday, February 19, 2002 8:37 AM
Chapter 8
Troubleshooting
LCD Messages
The following messages are displayed in the LCD when the machine is performing a function or encounters an error.
This section describes messages related to fax functions. For other messages → Reference Guide.
Message
Cause
Action
CHANGE DOCUMENT
When using the platen glass to send documents with Place the next document on the platen glass then
Book sending, you pressed Start without changing press Start.
the document.
DOCUMENT TOO LONG
HANG UP PHONE
The length of the document exceeds 356 mm.
The length of the document should be within 356
mm.
The handset is not placed in the handset cradle
correctly.
Replace the handset correctly.
MEM IN USE nn %
Shows the percentage of memory currently in use.
Wait for the machine to send any faxes in memory.
Also, print or delete any documents in memory you
no longer need. (→ pp. 4-15, 4-16)
MEMORY FULL
The memory becomes full during the document
scanning.
When sending the document, divide it into a few
parts or select a lower fax resolution.
If you need more space, wait for the machine to
send any faxes. Also, print or delete any documents
in memory you no longer need. (→ pp. 4-15, 4-16)
If the machine’s memory becomes full while
scanning documents using the ADF, the document
being scanned stops in the ADF. Press OK to make
the document come out automatically.
8
NO TEL
The one-touch speed dialling key or coded speed
dialling code you entered has not been registered.
Register the one-touch speed dialling key or coded
speed dialling code. (→ pp. 3-2, 3-4)
RECEIVED IN MEMORY
The machine received the fax in memory because
paper or toner ran out, or a paper jam occurred.
Load paper in the cassette (→ Quick Start Guide),
replace the cartridge (→ Reference Guide), or clear
the paper jam. (→ Reference Guide)
TX/RX NO. nnnn*
When the machine sends or receives a fax, it assigns Write the number down if you will need it later.
a unique identification number (nnnn).
* The identification number does not appear in the standby display. It appears when scanning documents, operating Fax Monitor or
Memory Reference, or receiving faxes in Manual mode.
8-1
Download from Www.Somanuals.com. All Manuals Search And Download.
08_EN.fm Page 2 Tuesday, February 19, 2002 8:37 AM
Faxing Problems
■ Sending Problems
❚ You cannot send a fax.
The machine may have overheated.
• Unplug the machine and let it cool for about 10 minutes. Then plug in the machine and try sending again.
The machine may not be set for the type of telephone line in use (pulse/tone).
• Make sure the machine is set for the correct telephone line type. (→ p. 2-7)
The document may not have been loaded.
• Remove the document, stack it if necessary, and place it on the platen glass or load it into the ADF correctly. (→ Reference
Guide)
• Make sure the feeder cover is closed.
The one-touch speed dialling key or coded speed dialling code you entered may not be registered for the feature you want
to use.
• Check the one-touch speed dialling key or coded speed dialling code and make sure it is registered correctly. (→ Chapter 3)
You dialled or have been provided with an incorrect number.
• Dial the number again, or check that you have the correct number.
The other party’s fax machine may be out of paper.
• Call the other party and ask them to make sure paper is loaded in their fax machine.
There may be other documents being sent from memory.
• Allow time for those documents to finish sending.
An error may have occurred during sending.
• Print an ACTIVITY REPORT and check for an error. (→ p. 7-2)
The telephone line may not be working properly.
• Make sure there is a dial tone when you lift the handset of the telephone connected to the machine. If there is no dial tone,
contact your local telephone company.
The receiving fax machine may not be a G3 fax machine.
• Make sure the receiving fax machine is compatible with the machine (which is a G3 fax machine).
The other party’s telephone may be busy or the other party’s fax machine may be turned OFF. 0018 BUSY/NO
SIGNAL is shown on the ERROR TX REPORT.
• The telephone number you dialled is busy. Try sending the document at a later time.
• The other party’s fax machine is not working. Contact the other party and have them check their fax machine.
• The receiving fax machine did not answer within 55 seconds (after all automatic redialling attempts). Contact the other party
and have them check their fax machine. For an overseas call, add pauses to the registered number. (→ p. 6-1)
The In Use lamp may be on.
• The In Use lamp may be on when turning off Energy Saver Mode, which means the extension phone is busy. Please wait until
the extension phone becomes free.
• There may be other documents being sent from memory. Allow time for those documents to finish sending.
❚ Faxes sent from the machine are spotted or dirty.
The receiving fax machine may not be working properly.
• Check the machine by making a copy (→ Reference Guide). If the copy is clear, the problem may be in the receiving fax
machine. If the copy is spotted or dirty, clean the platen glass or the rollers inside the main unit. (→ Reference Guide)
The document may not have been loaded.
• Remove the document, stack it if necessary, and place it on the platen glass or load it into the ADF correctly. (→ Reference
Guide)
8-2
Download from Www.Somanuals.com. All Manuals Search And Download.
08_EN.fm Page 3 Tuesday, February 19, 2002 8:37 AM
❚ Cannot send using Error Correction Mode (ECM).
The other party’s fax machine may not support ECM.
• If the other party’s fax machine does not support ECM, then the document is sent in normal mode without error checking.
ECM may be disabled.
• Make sure ECM is on. (→ p. 9-5)
❚ Errors occur frequently while sending.
The telephone lines may be in poor condition, or you may have a bad connection.
• Lower the transmission speed. (→ p. 9-4)
■ Receiving Problems
❚ Cannot receive a fax automatically.
The machine may not be set to receive automatically.
• For the machine to receive faxes automatically, the receive mode must be set to FaxTel, FaxOnly, AnsMode (→ Chapter
5). If you have set AnsMode, confirm that an answering machine is connected to the machine and that it is turned on with an
outgoing message properly recorded. (→ p. 5-2)
The machine’s memory is full.
• Print out or delete any documents stored in memory (→ pp. 4-15, 4-16) to free up space in the machine’s memory. Then ask
the other party to resend the fax.
An error may have occurred during reception.
• Print an ACTIVITY REPORT and check for an error. (→ p. 7-2)
No paper in the cassette.
• Make sure paper is loaded in the cassette. (→ Quick Start Guide)
8
The telephone line may not be connected properly.
• Make sure all line connections are secure. (→ Quick Start Guide)
❚ The machine does not switch automatically between telephone and fax reception.
The machine may not be set to switch automatically between telephone and fax reception.
• For the machine to switch automatically, the receive mode must be set to FaxTel, AnsMode (→ Chapter 5). If you have set
AnsMode, confirm that an answering machine is connected to the machine and that it is turned on with an outgoing message
properly recorded. (→ p. 5-2)
An error may have occurred during reception.
• Print an ACTIVITY REPORT and check for an error. (→ p. 7-2)
No paper may be loaded in the cassette.
• Make sure paper is loaded in the cassette. (→ Quick Start Guide)
The sending fax machine cannot send the CNG signal that tells the machine that the incoming signal is a fax.
• Some fax machines cannot send the CNG signal that tells your machine the incoming call is from a fax machine. In such cases,
you will have to receive the fax manually. (→ p. 5-6)
8-3
Download from Www.Somanuals.com. All Manuals Search And Download.
08_EN.fm Page 4 Tuesday, February 19, 2002 8:37 AM
❚ Cannot receive a document manually.
You may have disconnected the call by pressing Start or dialling the remote receiving ID after hanging up the handset.
• Always press Start or dial the remote receiving ID before hanging up the handset. Otherwise you will disconnect the call.
• When your telephone line uses rotary pulse, switch to tone dialling on your telephone before dialling 25 (the remote receiving
ID).
Energy Saver Mode may have been set.
• Disable Energy Saver Mode. (→ Reference Guide)
❚ Print quality is poor.
You may not be using the correct type of paper.
• Make sure you load paper that meets the paper requirements for the machine. (→ Reference Guide)
The sending fax machine may not be functioning properly.
• The sending fax machine usually determines the fax’s quality. Call the sender and have them make sure the top cover and
scanning glass of their fax machine are clean.
Error Correction Mode (ECM) may be disabled.
• Make sure ECM is on. (→ p. 9-6)
❚ Faxes do not print.
The cartridge may not be installed properly.
• Make sure the cartridge is installed properly. (→ Reference Guide)
The cartridge may need to be replaced.
• Determine if the problem is with the cartridge, and replace if necessary. (→ Reference Guide)
❚ Faxed images are blotched or uneven.
The telephone lines may be in poor condition, or you may have a bad connection.
• Error Correction Mode (ECM) sending/receiving should eliminate such problems. However, if the telephone lines are in poor
condition, you may have to try again.
The sending fax machine may not be functioning properly.
• The sending fax machine usually determines the fax’s quality. Call the sender and have them make sure the top cover and
scanning glass of their fax machine are clean.
❚ Cannot receive using Error Correction Mode (ECM).
The other party’s fax machine may not support ECM.
• If the other party’s fax machine does not support ECM, then the document is received in normal mode without error checking.
ECM may be disabled.
• Make sure ECM is on. (→ p. 9-6)
❚ Errors occur frequently while receiving.
The telephone lines may be in poor condition, or you may have a bad connection.
• Lower the reception speed. (→ p. 9-4)
The sending fax machine may not be functioning properly.
• Call the sender and have them check that their fax machine is functioning properly.
8-4
Download from Www.Somanuals.com. All Manuals Search And Download.
SB_PC1270D_FG_EN.book Page 5 Monday, February 18, 2002 12:20 PM
Telephone Problems
❚ You cannot dial.
The telephone line may not be connected properly.
• Make sure all line connections are secure. (→ Quick Start Guide)
The power cord may not be plugged in securely.
• Check that the power cord is plugged securely into the machine and into the wall outlet. Insert the power cord straight into the
power cord connector on the left side of the machine. Do not insert it at an angle. Otherwise, the machine may not be properly
connected to the power source and may not turn on. If this happens, disconnect the power cord, and reconnect it correctly after
a minute or more. (→ Quick Start Guide)
The machine may not be set for the type of telephone line in use (pulse/tone).
• Make sure the machine is set for the correct telephone line type. (→ p. 2-7)
❚ The telephone disconnects while you are talking.
The power cord may not be plugged in securely.
• Check that the power cord is plugged securely into the machine and into the wall outlet. Insert the power cord straight into the
power cord connector on the left side of the machine. Do not insert it at an angle. Otherwise, the machine may not be properly
connected to the power source and may not turn on. If this happens, disconnect the power cord, and reconnect it correctly after
a minute or more. (→ Quick Start Guide)
• Check that the modular cord is connected securely to the jacks on the machine, the telephone jack on your wall and the
connecting jack on your telephone.
If a Power Cut Occurs
If power is suddenly lost due to an outage or accidental unplugging, a built-in battery retains the user data settings and the speed
dialling settings. Any sent or received documents stored in memory will be backed up for about two hours.
During a power cut, functions are limited as follows:
8
• You cannot send, receive, or copy documents.
• You can make or receive calls.
When power is restored to the machine, the machine will automatically print a list of documents that were stored in memory at
the time of the power cut.
03/12 2001 15:38 FAX 123 4567
CANON
001
✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱
✱✱✱ MEMORY CLEAR REPORT ✱✱✱
✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱
MEMORY FILES DELETED
TX/RX NO
0023
MODE
DESTINATION TEL/ID
01] Canon CANADA
05] Canon OPTICS
32] Canon UK
PGS.
SET TIME
ST. TIME
SEQ. B’CAST
[
[
[
3
1
03/12 14:23
0024
TRANSMIT
03/12 14:28
• Make sure that A4-size paper is loaded in the cassette. If a different paper size is loaded, the report cannot be printed. Also, you cannot
use the multi-purpose tray for printing the report.
• If there is no paper in the cassette or no toner in the cartridge when power is restored, the MEMORY CLEAR REPORT will not be
printed.
8-5
Download from Www.Somanuals.com. All Manuals Search And Download.
SB_PC1270D_FG_EN.book Page 6 Monday, February 18, 2002 12:20 PM
If You Cannot Solve the Problem
If you have a problem with your machine and you cannot solve it by referring to the information in this chapter and in the
Reference Guide, contact your local authorised Canon dealer or the Canon Help Desk.
Canon’s support personnel are trained in the technical support of Canon’s products and should be able to help you with your
problem. The details on contacting your local authorised Canon dealer or the Canon Help Desk, → Reference Guide.
8-6
Download from Www.Somanuals.com. All Manuals Search And Download.
SB_PC1270D_FG_EN.book Page 1 Monday, February 18, 2002 12:20 PM
Chapter 9
Setting the Additional Functions
Understanding the “Additional Functions”
The menus of the Additional Functions can allow you to specify or register the various settings. Available menus differ
depending on the machine type. This section explains the procedure to access the menus, and the contents of the menus only
related to the fax functions.
• For the menus related to the common settings and the copy functions, → Reference Guide.
• Before adjusting any settings, you may want to print the USER’S DATA LIST to check the current settings. (→ p. 2-6)
■ Accessing the Additional Functions
1
Press Additional Functions to display the menus.
• The Additional Functions key blinks.
2
Press (–) or (+) to select the menu you want to change.
ADDITIONAL FUNCTIONS
3.FAX SETTINGS
Ex:
Ex:
3
4
5
Press OK.
FAX SETTINGS
1.USER SETTINGS
Use (–) or (+) to select the sub menu you want to change.
Press OK.
FAX SETTINGS
2.REPORT SETTINGS
REPORT SETTINGS
1.TX REPORT
• Details for sub menus, → pp. 9-2 to 9-10.
• After selecting the item or value with (–) or (+), press OK to enter the setting.
• Press Stop/Reset to exit from menu system.
9
9-1
Download from Www.Somanuals.com. All Manuals Search And Download.
SB_PC1270D_FG_EN.book Page 2 Monday, February 18, 2002 12:20 PM
■ Menu Descriptions
• The default settings and selectable settings vary depending on the current country selection. The values shown here are average values.
Print the USER’S DATA LIST to check the current settings. (→ p. 2-6)
COMMON SETTINGS
Name
Descriptions
DEFAULT SETTINGS
Selects which mode standby display appears in the LCD when the
power cord is connected, or the AUTO CLEAR function activates.
COPY
The copy mode is selected.
The fax mode is selected.
FAX
SW AFTER AUTO CLR
Selects whether the machine switches to the mode you set in
DEFAULT SETTINGS after the AUTO CLEAR function activates.
DEFAULT MODE
CURRENT MODE
The machine automatically switches to the mode you set in
DEFAULT SETTINGS after the AUTO CLEAR function activates.
The machine does not automatically switch to the mode you set in
DEFAULT SETTINGS even after the AUTO CLEAR function
activates.
VOLUME CONTROL
Adjusts the volume of the machine.
Adjusts the keypad volume.
1 to 3
1.KEYPAD VOLUME
ON
OFF
The volume is turned off.
Adjusts the alarm volume.
1 to 3
2.ALARM VOLUME
ON
OFF
The volume is turned off.
3.TX DONE TONE
Adjusts the volume of the done tone sounded when the machine has
finished sending faxes.
ON
1 to 3
ERROR ONLY
OFF
1 to 3
The volume is turned off.
4.RX DONE TONE
Adjusts the volume of the done tone sounded when the machine has
finished receiving faxes.
ON
1 to 3
ERROR ONLY
OFF
1 to 3
The volume is turned off.
5.PRINTING END TONE
Adjusts the volume of the done tone sounded when the machine has
finished printing.
ON
1 to 3
ERROR ONLY
OFF
1 to 3
The volume is turned off.
9-2
Download from Www.Somanuals.com. All Manuals Search And Download.
SB_PC1270D_FG_EN.book Page 3 Monday, February 18, 2002 12:20 PM
Name
Descriptions
6.SCANNING END TONE
Adjusts the volume of the done tone sounded when the machine has
finished scanning.
ON
1 to 3
ERROR ONLY
OFF
1 to 3
The volume is turned off.
Adjusts the calling volume.
1 to 3
7.CALLING VOLUME
8.LINE MONITOR VOL.
Adjusts the line monitor volume.
1 to 3
ON
OFF
The volume is turned off.
• MP TRAY PAPERSIZE, CAS. PAPER SIZE, PRINT EXPOSURE, MP PAPERTYPE, HIGH COPY MODE, TONER SAVER
MODE, PRT FEED INTERVAL and DISPLAY LANGUAGE, → Reference Guide.
COPY SETTINGS
For details, → Reference Guide.
9
9-3
Download from Www.Somanuals.com. All Manuals Search And Download.
09_EN.fm Page 4 Tuesday, February 19, 2002 8:38 AM
FAX SETTINGS
Name
USER SETTINGS
Descriptions
The basic operation settings in the Fax mode can be specified.
Specify the telephone line settings.
1.TEL LINE SETTINGS
1.USER TEL NO.
2.TEL LINE TYPE
TOUCH TONE
Your telephone and fax number can be registered. (→ p. 2-4)
Selects the telephone line type. (→ p. 2-7)
The telephone line is set for touch tone dialling.
The telephone line is set for rotary pulse dialling.
ROTARY PULSE
3.TX START SPEED
Sets the transmission speed for all documents you send.
14400bps/9600bps/7200bps/4800bps/2400bps
4.RX START SPEED
Sets the transmission speed for all documents you receive.
14400bps/9600bps/7200bps/4800bps/2400bps
2.UNIT NAME
You can register your name (or your company name). (→ p. 2-5)
3.TX TERMINAL ID
Prints your ID (transmitting terminal ID) on each page you transmit.
(→ p. 2-3)
ON
After you turn the terminal ID ON, you can do the following settings.
1.TTI POSITION
OUTSIDE IMAGE: Terminal ID is printed outside the image border.
INSIDE IMAGE: Terminal ID is printed inside the image border.
2.TEL NUMBER MARK
Selects the prefix for the identification header number.
FAX, TEL
OFF
No terminal ID is printed on the pages you send.
Sets the density of the documents.
Sets for dark documents.
4.DENSITY CONTROL
LIGHT
STANDARD
Sets for the documents of normal density.
Sets for light documents.
DARK
5.PROG 1-TOUCH KEY
Programs a fax function into the One-Touch key. The programmed
fax function will be executed by directly pressing the corresponding
One-Touch key. You do not need to press Function before pressing
the One-Touch key.
01 - 12
USE
Select the One-Touch key (01 to 12) in which you want to program
the fax function.
Uses PROGRAM 1-TOUCH KEY.
The following functions can be programmed:
1.REPORT;
2.DELAYED TX;
3.FAX MONITOR;
4.MEMORY REFERENCE;
5.BOOK SENDING.
6.D.T.
DO NOT USE
Disables PROGRAM 1-TOUCH KEY.
9-4
Download from Www.Somanuals.com. All Manuals Search And Download.
09_EN.fm Page 5 Tuesday, February 19, 2002 8:38 AM
Name
Descriptions
6.OFFHOOK ALARM
Enables/disables the offhook alarm that alerts you when the handset
is not in the handset cradle.
ON
After reception, the offhook alarm sounds when the handset of
extension telephone is left off the hook.
OFF
No offhook alarm.
7.R-KEY SETTING
The R-KEY setting allows you to set how the fax connects to PBX. If
your fax machine is not connected through a PBX, you can ignore
these settings.
PSTN
PBX
The fax is connected to the outside line.
The fax is connected through a PBX. Select one of the following
settings, depending on the type of PBX in service. Three settings are
available:
HOOKING
EARTH CONNECTION
PREFIX
If you select PREFIX, you can set a
number up to 20 digits long, including the
“P” at the end. (→ 2-8)
REPORT SETTINGS
1.TX REPORT
Sets the report setting.
Enables/disables automatic printing of a transmission report.
No report is printed.
OUTPUT NO
PRINT ERROR ONLY
REPORT WITH TX IMAGE
Prints a report only when a transmission error occurs.
If you select PRINT ERROR ONLY or OUTPUT YES, enables/
disables printing of the first page of the fax under the report.
ON
Prints a first page only when a transmission error occurs.
No first page is printed.
OFF
OUTPUT YES
2.RX REPORT
OUTPUT NO
Prints a report every time you send a document.
Enables/disables automatic printing of a reception report.
No report is printed.
9
PRINT ERROR ONLY
OUTPUT YES
3.ACTIVITY REPORT
Prints a report only when a reception error occurs.
Prints a report every time you receive a document.
Enables/disables automatic printing of an ACTIVITY REPORT after
every 20 transactions.
ON
OFF
Prints the ACTIVITY REPORT.
No ACTIVITY REPORT is printed.
TX SETTINGS
1.ECM TX
ON
Sets the transmission functions.
ECM (error correction mode) transmission is turned on or off.
All transmissions are conducted with ECM if the other party’s fax
supports ECM.
OFF
ECM is turned off.
9-5
Download from Www.Somanuals.com. All Manuals Search And Download.
SB_PC1270D_FG_EN.book Page 6 Monday, February 18, 2002 12:20 PM
Name
Descriptions
2.PAUSE TIME
Sets the length of the pause you insert into a dialling sequence.
1 to 15 SEC
3.AUTO REDIAL
Sets whether to perform automatic redial when the other line is busy
or no answer.
ON
Customises the redial operation.
1.REDIAL TIMES
Sets the number of retries.
1 to 10 TIMES
2.REDIAL INTERVAL
Sets period of time between rediallings.
2 to 99 MIN.
3.TX ERROR RESEND
ON
Redialling is attempted when a transmission error occurred.
RESEND TX FROM: Sets the number of pages to be sent when
redialling is attempted.
ERROR & 1ST PAGE, ERROR PAGE, ALL PAGES
OFF
Redialling is not attempted when a transmission error has occurred.
After the first attempt at dialling fails, redialling is not attempted.
Sets the ERASE FAILED TX function.
OFF
4.ERASE FAILED TX
ON
The document is deleted from the memory stored in the machine if a
transmission error has occurred.
OFF
5.TIME OUT
ON
The document is not deleted from the memory stored in the machine
even if a transmission error has occurred.
Enables/disables automatic scanning of documents after the fax
number is entered by using speed dialling.
Scanning begins automatically in 5 or 10 seconds after you enter the
phone number.
OFF
Press Start to scan document. Otherwise, the machine will return to
standby mode after 2 minutes.
RX SETTINGS
1.ECM RX
ON
Sets the reception functions.
ECM (error correction mode) receiving is turned on or off.
All receptions are conducted with ECM if the other party’s fax
supports ECM.
OFF
ECM is turned off.
2.FAX/TEL OPT.SET
1.RING START TIME
When FaxTel has been set, the optional settings are available.
Sets the duration that the machine listens for a fax tone before
starting to ring.
0 to 30 SEC
2.F/T RING TIME
Sets the length of time the machine rings to alert you of an incoming
call.
10 to 60 SEC
9-6
Download from Www.Somanuals.com. All Manuals Search And Download.
SB_PC1270D_FG_EN.book Page 7 Monday, February 18, 2002 12:20 PM
Name
3.F/T SWITCH ACTION
RECEIVE
Descriptions
Selects the action taken after the F/T RING TIME expires.
The fax switches to fax receive mode automatically at that point and
starts to receive the document.
DISCONNECT
The fax disconnects the call.
3.INCOMING RING
When the machine is set to FaxOnly, set whether the machine rings
when it receives a call.
OFF
The fax does not ring when it receives a fax. (In energy saver mode,
the fax may ring one or two times.)
ON
The fax rings when it receives a fax if a telephone is connected.
RING COUNT
Sets the number of incoming rings before the machine answers.
1 to 99 TIMES
4.MAN/AUTO SWITCH
Sets the machine to switch to document receive mode after ringing
for a specified length of time in the manual receive mode.
OFF
ON
The fax keeps ringing until someone answers the call manually with
a connected extension telephone.
F/T RING TIME: Sets the length of time to elapse before the
machine switches to the document receiving.
1 to 99 SEC
5.REMOTE RX
ON
Enables/disables remote receiving. (→ p. 5-5)
Remote receiving is turned on.
REMOTE RX ID
You can dial code on the remote extension to start receiving a
document.
A combination of two characters using 0 to 9, A and (25) is
possible.
OFF
Remote receiving is turned off.
Sets the print functions.
PRINTER SETTINGS
1.RX REDUCTION
ON
9
Receives images at a reduced size.
Turn on image reduction.
1.RX REDUCTION
AUTO SELECTION: Reducing size is set to auto.
FIXED REDUCTION: Reducing size is preset.
97%, 95%, 90%, 75%
2.SELECT REDUCE DIR
VERTICAL ONLY: Reduction is performed in the vertical direction
only.
HORIZ & VERTICAL: Reduction is performed in the horizontal
and vertical direction.
OFF
Image reduction is turned off.
9-7
Download from Www.Somanuals.com. All Manuals Search And Download.
09_EN.fm Page 8 Tuesday, February 19, 2002 8:39 AM
Name
Descriptions
2.TONER SUPPLY LOW
Ignores the warning and keeps printing until the document is
completely printed. This setting is convenient when a new cartridge
is not at hand.
KEEP PRINTING
The keep printing function is turned on. With this setting, the
machine will not store documents in memory if the toner has run out.
Re-set to RX TO MEMORY after replacing the cartridge with a new
one.
RX TO MEMORY
The machine receives the document in memory.
SYSTEM SETTINGS
Sets the functions of FAX DEFAULT, LOCK PHONE and COUNTRY
SELECT.
1.FAX DEFAULT
1.RESOLUTION
OFF
Sets the FAX DEFAULT functions.
Sets the fax resolution.
The setting of resolution set using Fax Resolution remains even
after the AUTO CLEAR function activates.
STANDARD
FINE
Suitable for most text-only documents.
Suitable for fine-print documents.
PHOTO
Suitable for documents that contain photographs.
SUPER FINE
Suitable for documents that contain fine print and images (the
resolution is four times that of STANDARD).
ULTRA FINE
Suitable for documents that contain fine print and images (the
resolution is eight times that of STANDARD).
2.BOOK TX SCAN SIZE
Selects the scanning size for the book sending function.
SHEET, A4, A5
2.LOCK PHONE
Sets the LOCK PHONE functions.
Outgoing voice call is operational.
Outgoing voice call is not operational.
OFF
ON
3.COUNTRY SELECT*
Selects the country where you are using your machine.
UK/GERMANY/FRANCE/ITALY/SPAIN/HOLLAND/DENMARK/
NORWAY/SWEDEN/FINLAND/AUSTRIA/BELGIUM/
SWITZERLAND/PORTUGAL/IRELAND/GREECE/
LUXEMBOURG/HUNGARY/CZECH/RUSSIA/SLOVENIA/SOUTH
AFRICA/OTHERS
* This setting is only available for some countries.
9-8
Download from Www.Somanuals.com. All Manuals Search And Download.
09_EN.fm Page 9 Tuesday, February 19, 2002 8:39 AM
ADD. REGISTRATION
Name
1-TOUCH SPD DIAL
1-TOUCH SPD DIAL
1.TEL NUMBER ENTRY
2.NAME
Descriptions
Registers the informations on One-Touch Speed Dialling. (→ p. 3-2)
Selects a one-touch speed dialling key.
Registers the other party’s telephone number.
Registers the other party’s name.
3.OPTIONAL SETTING
The transmission time and settings including the registration of
password and subaddress can be specified.
ON
The optional settings can be set.
1.TX TIME SETTING
5 settings of the transmission time can be specified.
Setting procedure
1 Select the time setting number (1 to 5) by pressing (–) or
(+), and press OK.
2 Enter the hour and minute for the transmission time using the
numeric keys, then press OK. (Enter 0 before the 1-digit hour or
minute. For example, enter “0905” for 9:05 am.)
• If you make a mistake while entering, press Function and
Clear, then enter the correct time.
Sending procedure
1 Load the document face down in the ADF or on the platen glass.
2 Press the one-touch speed dialling key on which the transmission
time is set. The document is scanned and stored in memory.
The machine transmits the document at the transmission time. If you
have set more than 2 transmission time settings, the document will be
transmitted at the preset time closest to the time that the document
has been scanned.
Once you set the transmission time, the machine will transmit the
document at the same time on every day.
However, you cannot use the one-touch speed dialling key to send
the document as usual, and cannot send the document any time
unless you cancel the transmission time setting.
To cancel the setting, press OK in TX TIME SETTING to select the
preset time, and press OK again. Then, press Function and Clear,
and press OK. The preset time is deleted.
9
If you have set more than 2 transmission time settings, repeat this
procedure to delete all the preset times. Or, when OFF is selected in
OPTIONAL SETTING, TX TIME SETTING and TX TYPE are
cancelled. You do not need to delete all the preset times.
2.TX TYPE
REGULAR TX: For a normal transmission.
SUBADDRESS TX: For a subaddress transmission.
Registers passwords and subadresses. (→ p. 3-12)
POLLING RX: For a polling reception. Registers passwords and
subadresses. (→ p. 5-6)
OFF
No optional setting.
9-9
Download from Www.Somanuals.com. All Manuals Search And Download.
09_EN.fm Page 10 Tuesday, February 19, 2002 8:39 AM
Name
Descriptions
CODED SPD DIAL
Registers the information on Coded Speed Dialling. (→ p. 3-4) To
register them, perform the same procedure with that of 1-TOUCH
SPD DIAL.
GROUP DIAL
Registers the information on Group Dialling. (→ p. 3-7)
1.TEL NUMBER ENTRY
Registers the other party’s telephone numbers by specifying the One-
Touch Speed Dialling keys or Coded Speed Dialling codes.
2.NAME
Registers the group’s name by specifying the One-Touch Speed
Dialling keys or Coded Speed Dialling codes.
3.TX TIME SETTING
Sets the transmission time.
5 settings of the transmission time can be specified.
To set them, peform the same procedure with that of 1-TOUCH SPD
DIAL.
TIMER SETTINGS
For details, → Reference Guide.
ADJUST/CLEAN
For details, → Reference Guide.
PRINT LISTS
Name
USER DATA
Descriptions
Prints out a list of items set or registered in the Additional Functions.
SPEED DIAL LIST
Prints the list of the fax/telephone numbers registered for the One-
Touch Speed Dialling keys, Coded Speed Dialling codes or Group
Dialling.
1.1-TOUCH LIST
1.NO SORT
Prints the 1-TOUCH LIST. (→ p. 3-9)
The printout of the list is not sorted.
The printout of the list is sorted.
2.SORT
2.CODED DIAL LIST
1.NO SORT
Prints the CODED DIAL LIST. (→ p. 3-10)
The printout of the list is not sorted.
The printout of the list is sorted.
2.SORT
3.1-TOUCH (DETAIL)
1.NO SORT
Prints the details of the 1-TOUCH LIST. (→ p. 3-10)
The printout of the list is not sorted.
The printout of the list is sorted.
2.SORT
4.CODED (DETAIL)
1.NO SORT
Prints the details of the CODED DIAL LIST. (→ p. 3-11)
The printout of the list is not sorted.
The printout of the list is sorted.
2.SORT
5.GROUP DIAL LIST
CANCEL REPORT
Prints the list of the Group Dialling.
Cancels printout of the report.
9-10
Download from Www.Somanuals.com. All Manuals Search And Download.
SB_PC1270D_FG_EN.book Page 1 Monday, February 18, 2002 12:20 PM
Appendix:
Specifications
Specifications are subject to change without notice.
■ Dialling
■ Facsimile
• Automatic dialling
■ Applicable Line
One-touch speed dialling (12 destinations)
Coded speed dialling (100 destinations)
Group dialling (Max. 111 destinations)
Directory dialling (with Directory key)
• Regular dialling (with numeric keys)
• Automatic redialling
Public Switched Telephone Network (PSTN)
■ Compatibility
G3
■ Data Compressing System
• Manual redialling (with Redial/Pause key)
MH, MR, MMR, JBIG
■ Networking
■ Modem Speed
• Sequential broadcast (Max. 122 destinations)
• Automatic reception
• Automatic Fax/Tel switchover
• Remote reception by telephone (Default ID: 25)
• Non-ring reception
• ECM deactivation
• ACTIVITY REPORT (after every 20 transactions)
• Non-delivery report
14400/9600/7200/4800/2400 bps
Automatic fallback
■ Transmission Speed
Approx. 6 seconds/page* at 14400 bps, ECM-MMR,
transmitting from memory
* Based on Canon FAX Standard Chart No. 1, standard
mode.
• TTI (Transmit Terminal Identification)
■ Scanning Image Processing
UHQ™ (Ultra High Quality) image enhancement
■ Telephone
■ Transmission/Reception Memory
■ Connection
Transmission: Maximum approx. 79 pages*
Reception: Maximum approx. 79 pages*
* Based on Canon FAX Standard Chart No. 1, standard
mode.
Telephone/answering machine (CNG detecting signal)/
data modem
A
■ Fax Scanning Speed
Approx. 3.4 seconds/page*
* Based on standard mode.
■ Fax Resolution
STANDARD: 8 pels/mm × 3.85 lines/mm
FINE: 8 pels/mm × 7.7 lines/mm
SUPER FINE: 8 pels/mm × 15.4 lines/mm
ULTRA FINE: 16 pels/mm × 15.4 lines/mm
A-1
Download from Www.Somanuals.com. All Manuals Search And Download.
SB_PC1270D_FG_EN.book Page 2 Monday, February 18, 2002 12:20 PM
A-2
Download from Www.Somanuals.com. All Manuals Search And Download.
SB_PC1270D_FG_EN.book Page 1 Monday, February 18, 2002 12:20 PM
Index
(–) key...........................................................................1-1
(+) key...........................................................................1-1
1-TOUCH
C
CANCEL REPORT setting............................................. 9-10
Cancelling
SPD DIAL setting .........................................................9-9
1-TOUCH LIST
description .....................................................................7-1
printing ..........................................................................3-9
sample.................................................................. 3-9, 3-10
automatic redialling ...................................................... 4-8
manual redialling .......................................................... 4-8
polling receiving........................................................... 5-7
printing lists ................................................................ 3-11
receiving ....................................................................... 5-8
restriction...................................................................... 6-4
sending.......................................................................... 4-7
CHANGE DOCUMENT message.................................... 8-1
Clear key ........................................................................... 1-2
Coded Dial key ................................................................. 1-2
CODED DIAL LIST
description..................................................................... 7-1
printing.......................................................................... 3-9
sample................................................................3-10, 3-11
CODED SPD DIAL setting ............................................ 9-10
Coded speed dialling
changing, deleting......................................................... 3-5
description..................................................................... 3-1
registering numbers for................................................. 3-4
using.............................................................................. 4-3
Confirming
sending reservation..................................................... 4-12
transmission status...................................................... 4-12
Conventions, type .................................................................v
COPY key ......................................................................... 1-1
CURRENT MODE setting ............................................... 9-2
Customer support.............................................................. 1-1
A
Accessing menus ...............................................................9-1
ACTIVITY REPORT
description ............................................................. 7-1, 7-2
printing ..........................................................................7-2
sample............................................................................7-2
setting ............................................................................9-5
Additional Functions
accessing........................................................................9-1
key .................................................................................1-1
understanding ................................................................9-1
Alarm indicator..................................................................1-1
ALARM VOLUME setting...............................................9-2
AnsMode, description........................................................5-1
AUTO REDIAL settings ...................................................9-6
Automatic redialling
cancelling.......................................................................4-8
description .....................................................................4-8
B
Book Sending key..............................................................1-2
BOOK TX SCAN SIZE setting.........................................9-8
Broadcasting, sequential....................................................4-9
BUSY/NO SIGNAL..........................................................8-2
I
I-1
Download from Www.Somanuals.com. All Manuals Search And Download.
SB_PC1270D_FG_EN.book Page 2 Monday, February 18, 2002 12:20 PM
D
G
D.T. key.............................................................................1-2
Date, entering.....................................................................2-4
DEFAULT MODE setting.................................................9-2
DEFAULT SETTINGS.....................................................9-2
Delayed sending ..............................................................4-11
Delayed Transmission key....................................... 1-2, 4-11
Delete key..........................................................................1-2
Deleting document from memory....................................4-16
DENSITY CONTROL settings.........................................9-4
Dial tone, confirming.........................................................6-3
Dialling
coded speed ..................................... 3-1, 3-4, 3-5, 3-6, 4-3
group........................................................3-1, 3-7, 3-8, 4-4
methods .........................................................................4-2
one-touch speed.......................................3-1, 3-2, 3-3, 4-3
overseas number............................................................6-1
regular............................................................................4-2
speed (See Speed dialling)
GROUP DIAL LIST
description..................................................................... 7-1
printing.......................................................................... 3-9
sample......................................................................... 3-11
GROUP DIAL setting..................................................... 9-10
Group dialling
creating groups.............................................................. 3-7
description..................................................................... 3-1
using.............................................................................. 4-4
H
HANG UP PHONE message............................................ 8-1
I
In Use/Memory indicator.................................................. 1-1
INCOMING RING settings .............................................. 9-7
INSIDE IMAGE setting.................................................... 9-4
switching temporarily to tone........................................6-2
through switchboard......................................................2-7
with pauses ....................................................................6-1
Directory key.....................................................................1-2
Document
in memory....................................................................4-13
printing document in memory.....................................4-15
printing list of documents in memory .........................4-13
DOCUMENT MEMORY LIST
description .....................................................................7-1
printing ........................................................................4-13
sample..........................................................................4-13
DOCUMENT TOO LONG message.................................8-1
K
KEEP PRINTING setting ................................................. 9-8
KEYPAD VOLUME setting............................................. 9-2
Keys (See also individual key names)
numeric ......................................................................... 1-1
one-touch speed dialling............................................... 1-2
L
LCD................................................................................... 1-1
messages (See also individual message names) ........... 8-1
Letters, entering ................................................................ 2-2
LINE MONITOR VOL. setting........................................ 9-3
List (See individual list names)
E
ECM
LIST setting
1-TOUCH ................................................................... 9-10
CODED DIAL............................................................ 9-10
GROUP DIAL ............................................................ 9-10
SPEED DIAL.............................................................. 9-10
LOCK PHONE setting...................................................... 9-8
RX setting......................................................................9-6
TX setting......................................................................9-5
Energy Saver key...............................................................1-1
ERASE FAILED TX setting .............................................9-6
ERROR TX REPORT, sample..........................................7-3
F
F/T RING TIME setting ....................................................9-6
F/T SWITCH ACTION setting ................................. 5-4, 9-7
FAX
key .................................................................................1-1
mode..............................................................................1-3
FAX DEFAULT settings...................................................9-8
Fax Monitor key ................................................................1-2
FaxOnly
description ............................................................. 5-1, 5-2
Fax Resolution key............................................................1-2
FaxTel
description ............................................................. 5-1, 5-2
setting options for..........................................................5-3
FAX/TEL OPT. SET settings............................................9-6
FINE
description .....................................................................4-1
setting .................................................................... 4-1, 9-8
Function key ......................................................................1-2
I-2
Download from Www.Somanuals.com. All Manuals Search And Download.
SB_PC1270D_FG_EN.book Page 3 Monday, February 18, 2002 12:20 PM
M
P
MAN/AUTO SWITCH settings ........................................9-7
Manual
PAUSE TIME setting ....................................................... 9-6
Pauses, dialling with ......................................................... 6-1
PHOTO
description..................................................................... 4-1
setting.....................................................................4-1, 9-8
Polling........................................................................5-6, 5-7
Power cut .......................................................................... 8-5
PRINTER SETTINGS...................................................... 9-7
Printing
1-TOUCH LIST............................................................ 3-9
ACTIVITY REPORT................................................... 7-2
CODED DIAL LIST..................................................... 3-9
document in memory.................................................. 4-15
DOCUMENT MEMORY LIST ................................. 4-13
GROUP DIAL LIST..................................................... 3-9
list of documents in memory ...................................... 4-13
speed dialling lists......................................................... 3-9
USER’S DATA LIST................................................... 2-6
PRINTING END TONE setting ....................................... 9-2
Problems
description ............................................................. 5-1, 5-2
receiving in....................................................................5-5
Manual redialling...............................................................4-8
cancelling.......................................................................4-8
MEM IN USE nn % message............................................8-1
Memory
deleting document from...............................................4-16
documents in................................................................4-13
printing document in ...................................................4-15
printing list of documents in........................................4-13
receiving when problem occurs.....................................5-8
sending (See Memory sending)
MEMORY CLEAR REPORT
description .....................................................................8-5
sample............................................................................8-5
MEMORY FULL message................................................8-1
Memory Reference key .....................................................1-2
Memory sending
cancelling.......................................................................4-7
using, ADF ....................................................................4-5
using, platen glass..........................................................4-6
Menu descriptions..............................................................9-2
Messages, LCD (See also individual message names)
descriptions....................................................................8-1
Mistake, correcting ............................................................2-2
MULTI TX/RX (Transaction) REPORT...........................7-4
cannot solve .................................................................. 8-6
faxing............................................................................ 8-2
receiving ....................................................................... 8-3
receiving in memory when ........................................... 5-8
sending.......................................................................... 8-2
telephone....................................................................... 8-5
PROG 1-TOUCH KEY settings ....................................... 9-4
Q
N
Quality, adjusting.............................................................. 4-1
NAME setting
for 1-TOUCH SPD DIAL .............................................9-9
for GROUP DIAL .......................................................9-10
NO TEL message...........................................................8-1
Numbers, entering .............................................................2-2
Numeric keys.....................................................................1-1
O
OFFHOOK ALARM setting .............................................9-5
OK key...............................................................................1-1
One-touch speed dialling
I
changing, deleting .........................................................3-3
description .....................................................................3-1
keys................................................................................1-2
registering numbers for .................................................3-2
using ..............................................................................4-3
Operation panel
registering information via............................................2-1
OPTIONAL SETTING
for 1-TOUCH SPD DIAL .............................................9-9
OUTSIDE IMAGE setting ................................................9-4
Overseas number, dialling .................................................6-1
I-3
Download from Www.Somanuals.com. All Manuals Search And Download.
SB_PC1270D_FG_EN.book Page 4 Monday, February 18, 2002 12:20 PM
R
S
R key..................................................................................1-2
R-KEY SETTING .............................................................9-5
Receive Mode key .............................................................1-2
Receive Mode settings.......................................................5-2
RECEIVED IN MEMORY message.................................8-1
Receiving (See also individual receive modes)
cancelling.......................................................................5-8
in memory when problem occurs..................................5-8
manually........................................................................5-5
methods ................................................................. 5-1, 5-2
problems........................................................................8-3
while performing other tasks.........................................5-8
REDIAL
INTERVAL setting .......................................................9-6
TIMES setting ...............................................................9-6
Redial/Pause key................................................................1-2
Redialling
automatic .......................................................................4-8
manual ...........................................................................4-8
Registering
coded speed dialling......................................................3-4
one-touch speed dialling................................................3-2
password and subaddress.....................3-12, 3-13, 5-6, 5-7
sender information.........................................................2-3
via operation panel ........................................................2-1
Regular dialling .................................................................4-2
REMOTE
RX ID setting.................................................................9-7
RX settings ....................................................................9-7
Report (See also individual report names)
settings...........................................................................9-5
Report key..........................................................................1-2
REPORT SETTINGS........................................................9-5
REPORT WITH TX IMAGE setting ................................9-5
Resolution, setting scanning..............................................4-1
RESOLUTION settings.....................................................9-8
Restricting use of machine ................................................6-3
RING
Scanning
resolution, setting.......................................................... 4-1
SCANNING END TONE setting ..................................... 9-3
SELECT REDUCE DIR setting ....................................... 9-7
Sender information
description..................................................................... 2-3
printing list to check ..................................................... 2-6
registering ..............................................................2-4, 2-5
Sending
cancelling...................................................................... 4-7
delayed........................................................................ 4-11
memory......................................................................... 4-5
methods......................................................................... 4-5
preparing....................................................................... 4-1
problems ....................................................................... 8-2
sequential broadcasting........................................4-9, 4-10
setting scanning resolution ........................................... 4-1
timer (See Delayed sending)
to more than one destination................................4-9, 4-10
using coded speed dialling............................................ 4-3
using group dialling...................................................... 4-4
using one-touch speed dialling ..................................... 4-3
Setting
resolution ...................................................................... 4-1
Settings, list of ................................................................ 9-10
SHORT-LONG-SHORT setting....................................... 9-7
SHORT-SHORT-LONG setting....................................... 9-7
Space key .......................................................................... 1-2
Special Dialling................................................................. 6-1
SPEED DIAL LIST setting............................................. 9-10
Speed dialling
coded...............................................................3-1, 3-4, 4-3
description..................................................................... 3-1
group dialling..................................................3-1, 3-7, 4-4
lists................................................................................ 3-9
methods......................................................................... 3-1
one-touch ........................................................3-1, 3-2, 4-3
STANDARD
COUNT setting..............................................................9-7
START TIME setting....................................................9-6
ROTARY PULSE setting.......................................... 2-7, 9-4
RX
(Reception) REPORT....................................................7-4
DONE TONE setting.....................................................9-2
REDUCTION settings...................................................9-7
REPORT settings ..........................................................9-5
SETTINGS sub menu....................................................9-6
START SPEED setting .................................................9-4
TO MEMORY setting...................................................9-8
description..................................................................... 4-1
setting.....................................................................4-1, 9-8
Standby display, fax mode................................................ 1-3
Start key ............................................................................ 1-1
Stop/Reset key .................................................................. 1-1
SUPER FINE
description..................................................................... 4-1
setting.....................................................................4-1, 9-8
Support, customer ............................................................. 1-1
SW AFTER AUTO CLR setting ...................................... 9-2
Symbols, entering ............................................................. 2-2
SYSTEM SETTINGS....................................................... 9-8
I-4
Download from Www.Somanuals.com. All Manuals Search And Download.
SB_PC1270D_FG_EN.book Page 5 Monday, February 18, 2002 12:20 PM
T
TEL LINE SETTINGS......................................................9-4
TEL LINE TYPE settings..................................................9-4
TEL NO. setting ................................................................9-4
TEL NUMBER
ENTRY setting for 1-TOUCH SPD DIAL ...................9-9
ENTRY setting for GROUP DIAL .............................9-10
TEL NUMBER MARK setting .........................................9-4
Telephone
line (See Telephone line)
problems........................................................................8-5
Telephone line, setting type...............................................2-7
Time, entering....................................................................2-4
TIME OUT setting.............................................................9-6
Timer sending (See Delayed sending)
Tone/+ key.........................................................................1-1
Tone dialling, switching to................................................6-2
TONER SUPPLY LOW setting ........................................9-8
TOUCH TONE setting .............................................. 2-7, 9-4
TTI POSITION setting ......................................................9-4
TX
(Transmission) REPORT ..............................................7-3
DONE TONE setting.....................................................9-2
ERROR RESEND setting .............................................9-6
REPORT settings ..........................................................9-5
START SPEED setting .................................................9-4
TERMINAL ID setting .................................................9-4
TIME SETTING.................................................. 9-9, 9-10
SETTINGS sub menu....................................................9-5
TYPE settings................................................................9-9
TX/RX NO. nnnn message............................................8-1
U
ULTRA FINE
description .....................................................................4-1
setting .................................................................... 4-1, 9-8
UNIT NAME setting .........................................................9-4
USER
DATA setting ..............................................................9-10
SETTINGS....................................................................9-4
USER’S DATA LIST
description .....................................................................7-1
printing ..........................................................................2-6
sample............................................................................2-6
I
V
VOLUME CONTROL setting...........................................9-2
I-5
Download from Www.Somanuals.com. All Manuals Search And Download.
SB_PC1270D_FG_EN.book Page 6 Monday, February 18, 2002 12:20 PM
Memo
I-6
Download from Www.Somanuals.com. All Manuals Search And Download.
|