Facsimile Guide
Please read this guide before operating this equipment.
After you finish reading this guide, store it in a safe
place for future reference.
Download from Www.Somanuals.com. All Manuals Search And Download.
Manuals for the Machine
The manuals for this machine are divided as follows. Please refer to them for detailed information.
Depending on the system configuration and product purchased, some manuals may not be needed.
Guides with this symbol are PDF manuals included on the
Guides with this symbol are printed manuals.
CD-ROM
accompanying CD-ROM.
• Setting Up the Machine
• Software Installation
Set-Up Sheet
• Network Setting (Only for the MF5770 model.)
• Introduction on Machine Use
Quick Reference Guide
• Copying and Printing Instructions
• Troubleshooting
CD-ROM
User’s Guide
• Fax Instructions
• Troubleshooting
Facsimile Guide
(This Manual)
Only for the MF5750/MF5770 models.
• Software Installation and Instructions
• Printing, Scanning and PC Faxing Instructions
• Troubleshooting
CD-ROM
Software Guide
• Remote User Interface Instructions
CD-ROM
CD-ROM
Remote UI Guide
Only for the MF5770 model.
• Network Connectivity and Setup Instructions
Network Guide
Only for the MF5770 model.
• To view the manual in PDF format, Adobe Reader/Acrobat Reader/Acrobat is required. If Adobe Reader/Acrobat Reader/Acrobat is not installed on your
system, please download it from the Adobe Systems Incorporated website .
Download from Www.Somanuals.com. All Manuals Search And Download.
Trademarks
Canon® is a registered trademark, and UHQ™ is a trademark of Canon Inc.
IBM® is a registered trademark.
Microsoft® and Windows® are registered trademarks of Microsoft Corporation.
Other brand and product names may be trademarks or registered trademarks
of their respective companies.
As an ENERGY STAR® Partner, Canon has determined
that the machine meets the Energy Star guidelines for
energy efficiency.
Super G3 is a phrase used to describe the new
generation of fax machines that use ITU-T V.34
standard 33.6Kbps* modems. Super G3 High Speed
Fax machines allow transmission time of approx. 3
seconds* per page which results in reduced telephone
line charges.
* Approx. 3 seconds per page fax data transmission time based on Canon FAX
Standard Chart No.1, (Standard Mode) at 33.6Kbps modem speed. The Public
Switched Telephone Network (PSTN) currently supports 28.8Kbps modem speeds or
lower, depending on telephone line conditions.
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Preface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v
How to Use This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .v
Symbols Used in This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .v
Keys Used in This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .v
Messages Displayed in the LCD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .v
Chapter 1
Chapter 2
Introduction
Customer Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Operation Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Standby Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Entering the Date and Time. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
Registering Your Fax/Telephone Number and Name. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
Setting the Telephone Line Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
Dialing Through a Switchboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
Chapter 3
Speed Dialing Methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
Registering One-Touch Speed Dialing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
Registering Coded Speed Dialing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
Registering Group Dialing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
Chapter 4
Sending Faxes
Improving Faxed Images . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
Adjusting the Image Quality (Fax Resolution) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
Adjusting the Exposure (Scan Density) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
Dialing Methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4
Regular Dialing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4
One-Touch Speed Dialing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4
Coded Speed Dialing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
Group Dialing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
Directory Dialing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
Redialing a Busy Number. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
Manual Redialing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
Automatic Redialing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
Sending the Same Document to Several Recipients (Sequential Broadcasting) . . . . . . . . . . . . . . 4-7
Special Dialing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8
Dialing an Overseas Number (With Pauses) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8
Switching Temporarily to Tone Dialing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5
Receiving Both Faxes and Voice Calls Automatically: FaxTel Mode . . . . . . . . . . . . . . . . . . . 5-2
Receiving When an Answering Machine Is Connected: AnsMode . . . . . . . . . . . . . . . . . . . . 5-3
Receiving Faxes While Performing Other Tasks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5
Receiving Faxes in the Memory When a Problem Occurs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5
Canceling Receiving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5
Chapter 6
Summary of Reports and Lists . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
Adjusting the ACTIVITY REPORT Setting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-3
Adjusting the RX REPORT Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-5
Printing the USER DATA LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-6
Chapter 7
Troubleshooting
LCD Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1
Error Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3
Faxing Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-5
Sending Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-5
Receiving Problems. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-8
Telephone Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-11
If a Power Cut Occurs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-12
If You Cannot Solve the Problem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-12
Chapter 8
Chapter 9
Machine Settings
Accessing the Machine Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1
Menu Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1
FAX SETTINGS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1
ADD. REGISTRATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-8
REPORTS / LISTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-8
Appendix
Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1
Facsimile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1
Telephone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-2
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-3
iv
Download from Www.Somanuals.com. All Manuals Search And Download.
Preface
Thank you for purchasing the Canon LaserBase MF5750/MF5770. Please read this manual thoroughly before
operating the machine in order to familiarize yourself with its capabilities, and to make the most of its many
functions. After reading this manual, store it in a safe place for future reference.
How to Use This Manual
Symbols Used in This Manual
The following symbols are used in this manual to explain procedures, restrictions, handling
precautions, and instructions that should be observed for safety.
Indicates a warning concerning operations that may lead to death or injury to persons
if not performed correctly. In order to use the machine safely, always pay attention to
these warnings.
WARNING
Indicates a caution concerning operations that may lead to injury to persons, or
damage to property if not performed correctly. In order to use the machine safely,
always pay attention to these cautions.
CAUTION
Indicates operational requirements and restrictions. Be sure to read these items
carefully in order to operate the machine correctly, and to avoid damage to the
machine.
IMPORTANT
Indicates a clarification of an operation, or contains additional explanations for a
procedure. Reading these notes is highly recommended.
NOTE
Keys Used in This Manual
The following symbols and key names are a few examples of how keys to be pressed are expressed in
this manual. The operation panel keys on the machine are indicated within brackets.
Press [Start].
Press [Image Quality].
Messages Displayed in the LCD
The following are a few examples of how messages in the LCD are expressed in this manual. The
messages are indicated within angle brackets.
• If <MEMORY FULL> is displayed, the machine cannot scan the documents.
• <NOT REGISTERED> appears if there are no numbers registered.
v
Download from Www.Somanuals.com. All Manuals Search And Download.
1
Introduction
CHAPTER
This chapter describes the operation panel and the standby display used for the fax function of the machine.
Customer Support
The machine is designed with the latest technology to provide trouble-free operation. If you encounter
a problem with the machine's operation, try to solve it by using the information in Chapter 7,
"Troubleshooting." If you cannot solve the problem or if you think the machine needs servicing, contact
your local authorized Canon dealer or the Canon help line.
Operation Panel
This section describes keys used when sending and receiving faxes, and setting the Menu.
For keys not described here, see Chapter 1, "Introduction," in the User’s Guide.
■ MF5770
a
b c de
f
gh
i
j
COPY
SCAN
FAX
ABC
JKL
DEF
Redial /
01
04
07
10
02
05
08
11
03
1
2
5
8
0
3
MNO
Pause
GHI
Menu
06
09
Coded
Dial
4
6
WXYZ
/
PQRS
TUV
Directory
Hook
C
7
9
R
12
OK
T
u
k l
m
n o
p
q
r
s
t
a
b
One-Touch Speed Dialing keys
Dial fax/telephone numbers registered under one-touch speed
dialing keys.
c
d
Redial/Pause key
Redials the previous number dialed manually with the numeric
keys, and enters pauses when dialing or registering the
numbers.
Coded Dial key
Press [Coded Dial], followed by a two-digit code to dial fax/telephone
number registered for coded speed dialing.
In Use/Memory indicator
Flashes green when a fax is being received or sent, or the
extension phone is off the hook.
Lights green when there are waiting fax jobs, or a fax is
received into the memory.
1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
e
Alarm indicator
Flashes red when the machine has a problem such as a paper jam.
(The error message is displayed in the LCD.)
n
o
p
Status Monitor key
Checks the status of copy, fax, print and report jobs.
Clear key
Clears an entry in the LCD.
f
g
h
i
j
FAX key
Switches the standby display to the Fax mode.
LCD
Menu key
Customizes the way the machine operates.
Displays messages and prompts during operation. Also
displays selections, text, and numbers when specifying
settings.
[
(-)] or [ (+)] keys
Scroll through the selections so you can see other settings.
q
r
Start key
Starts sending or receiving faxes.
Exposure key
Adjusts the fax exposure.
1
Stop/Reset key
Cancels sending or receiving faxes and other operations, and
turns to the standby display in the LCD.
Energy Saver key
Sets or cancels the energy saver mode manually. The key lights
green when the energy saver mode is set, and goes off when the
mode is canceled.
s
t
u
OK key
Determines the contents you set or register.
k
l
R key
Image Quality key
Adjusts the quality of fax image.
Dials an outside line access number when the machine is connected
through a switchboard (PBX).
Numeric keys
Enter numbers when dialing or registering fax/telephone
Directory key
Enables you to search for fax/telephone numbers by the name under
which they are registered for speed dialing, and then use the number
for dialing.
numbers, etc. Also, enter characters when registering names.
m
Hook key
Enables you to dial without picking up the handset.
■ MF5750
a
b c de
f
gh
i
j
COPY
SCAN
FAX
ABC
DEF
Redial /
01
04
07
10
02
05
08
11
03
1
2
3
MNO
Pause
GHI
JKL
Menu
06
09
Coded
Dial
4
5
6
WXYZ
PQRS
TUV
Directory
Hook
8
9
7
R
12
OK
0
T
u
k l
m
n o
p
q
r
s
t
1-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Standby Display
The standby display differs depending on which mode is selected.
The standby display in the Fax mode is as follows:
■ Fax Mode
1
Date & time
Receive mode
Image quality
NOTE
For the standby display in the Copy mode and the Scan mode, see Chapter 1, "Introduction," in the User’s Guide.
1-3
Download from Www.Somanuals.com. All Manuals Search And Download.
2
Registering Information in Your Machine
CHAPTER
This chapter explains how to register the information necessary for sending and receiving faxes.
NOTE
•
For details on how to enter characters or symbols when you come to step that requires you to enter a name or
number, see Chapter 2, "Operation," in the Quick Reference Guide.
•
You can print the USER DATA LIST to check the sender information you have registered. (See "Printing the USER
DATA LIST," on p. 6-6.)
Registering Sender Information
When you receive a fax, the name of the person or company who sent you the fax, their fax/telephone
number, and the date and time of transmission may be printed in small type at the top of each page.
This information is called the Sender information or the Transmit Terminal Identification (TTI). Similarly,
you can register your details in your machine so that whenever you send a fax, the other party knows
who sent it, and when it was sent.
Below is an example of how your sender information would print on a fax sent from your machine:
01/02 2005 15:33 FAX 123 4567
YOUR NAME
001/001
Date and time of
transmission
THE SLEREXE COMPANY LIMITED
SAPORS LANE•BOOLE•DORSET•BH25 8ER
TELEPHONE BOOLE (945 13) 51617
–
FAX 1234567
Your fax/telephone
number.
You can select <FAX>
or <TEL> to be
Our Ref. 350/PJC/EAC
displayed in front of the
number. (See <2. TEL
NUMBER MARK> on
p. 8-3.)
Page number
Your name
NOTE
You can set the sender information to print inside or outside the image area. (See <1. TTI POSITION> of "Menu
Descriptions," on p. 8-2.)
2-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Entering the Date and Time
NOTE
You can print the USER DATA LIST to check the current setting. (See "Printing the USER DATA LIST," on p. 6-6.)
1
2
3
4
Press [Menu].
Press [ (-)] or [ (+)] to select <TIMER SETTINGS> ➞ press [OK].
Press [ (-)] or [ (+)] to select <DATE/TIME SETTING> ➞ press [OK].
Use the numeric keys to enter the date (day/month/year) and time (in 24-hour format) ➞ press [OK].
2
DATE/TIME SETTING
01/02 '05 11:01
TIMER SETTINGS
2.DATE SETUP
➞
Enter only the last two digits of the year.
5
Press [Stop/Reset] to return to the standby display.
Registering Your Fax/Telephone Number and Name
1
2
3
4
5
6
Press [Menu].
Press [ ] or [ ] to select <FAX SETTINGS> ➞ press [OK].
Press [ (-)] or [ (+)] to select <USER SETTINGS> ➞ press [OK].
Press [ (-)] or [ (+)] to select <TEL LINE SETTINGS> ➞ press [OK].
Press [ (-)] or [ (+)] to select <UNIT TEL NUMBER> ➞ press [OK].
Use the numeric keys to enter your fax/telephone number (max. 20 digits, including spaces) ➞ press
[OK].
UNIT TEL NUMBER
123xxxxxxx
TEL LINE SETTINGS
2.TEL LINE TYPE
➞
To enter a plus sign (+) before the number, press [#].
To delete a previous number, press [ (-)] or [Clear]. To delete the entire entry, press and hold [Clear].
7
8
Press [Menu].
Press [ (-)] or [ (+)] to select <UNIT NAME> ➞ press [OK].
2-2
Download from Www.Somanuals.com. All Manuals Search And Download.
9
Use the numeric keys to enter your name (max. 24 characters, including spaces) ➞ press [OK].
For details on how to enter characters or symbols, see "2.3 Enter Characters," in the Quick Reference Guide.
UNIT NAME
CANON
:A
USER SETTINGS
3.TX TERMINAL ID
➞
10 Press [Stop/Reset] to return to the standby display.
Setting the Telephone Line Type
2
Before using the machine, make sure you have set the correct telephone line type for your telephone
line. If you are unsure of your telephone line type, contact your telephone company.
NOTE
You can print the USER DATA LIST to check the current setting. (See "Printing the USER DATA LIST," on p. 6-6.)
1
2
3
4
5
6
Press [Menu].
Press [ (-)] or [ (+)] to select <FAX SETTINGS> ➞ press [OK].
Press [ (-)] or [ (+)] to select <USER SETTINGS> ➞ press [OK].
Press [ (-)] or [ (+)] to select <TEL LINE SETTINGS> ➞ press [OK].
Press [ (-)] or [ (+)] to select <TEL LINE TYPE> ➞ press [OK].
Press [ (-)] or [ (+)] to select the telephone line type ➞ press [OK].
You can select from the following:
-
-
<TOUCH TONE> for tone dialing
<ROTARY PULSE> for pulse dialing
7
Press [Stop/Reset] to return to the standby display.
Dialing Through a Switchboard
A PBX (Private Branch Exchange) is an on-site telephone switchboard. If your machine is connected
through a PBX or other telephone switching system, you have to dial the outside line access number
first, and then the number of the party you are calling.
To facilitate this procedure, you can register the PBX access type and the outside line access number
under [R] so that you only need to press this key before dialing the fax/telephone number you want to
reach.
NOTE
You can print the USER DATA LIST to check the current setting. (See "Printing the USER DATA LIST," on p. 6-6.)
2-3
Download from Www.Somanuals.com. All Manuals Search And Download.
1
2
3
4
5
6
Press [Menu].
Press [ (-)] or [ (+)] to select <FAX SETTINGS> ➞ press [OK].
Press [ (-)] or [ (+)] to select <USER SETTINGS> ➞ press [OK].
Press [ (-)] or [ (+)] to select <R-KEY SETTING> ➞ press [OK].
Press [ (-)] or [ (+)] to select <PBX> ➞ press [OK].
Press [ (-)] or [ (+)] to select the access type of your switching system.
If you selected <HOOKING>:
●
●
2
❑
Press [OK].
If you selected <PREFIX>:
❑
❑
Press [OK].
Use the numeric keys to enter the outside line access number (max. 19 digits) ➞ [Redial/Pause] to enter a
pause ➞ [OK].
NOTE
If you do not press [Redial/Pause] before pressing [OK], you cannot complete the registration.
7
Press [Stop/Reset] to return to the standby display.
2-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Speed Dialing
CHAPTER
This chapter explains how to simplify the dialing process by assigning the recipient names and their fax/telephone
numbers to only one or two keys.
Speed Dialing Methods
Speed dialing allows you to dial fax/telephone numbers by simply pressing one or a few keys.
The following speed dialing methods are available:
■ One-Touch Speed Dialing
Register a fax/telephone number for one-touch speed dialing (see "Registering One-Touch Speed Dialing," on p.
3-1), then to dial the number, simply press the one-touch speed dialing key assigned to that number.
■ Coded Speed Dialing
Register a fax/telephone number for coded speed dialing (see "Registering Coded Speed Dialing," on p. 3-3), then
■ Group Dialing
Register a group of fax/telephone numbers for group dialing (see "Registering Group Dialing," on p. 3-4), then to send
a document to all numbers in that group, simply press the one-touch speed dialing key, or press [Coded Dial] ➞ enter
the two-digit code assigned to that group.
NOTE
After you set up your speed dialing keys, we recommend that you occasionally print a list of all fax/telephone
numbers registered in the machine, and store it for reference. (See "Printing Speed Dialing Lists," on p. 3-6.)
Registering One-Touch Speed Dialing
Before you can use one-touch speed dialing (see "One-Touch Speed Dialing," on p. 4-4), you need to
register the recipients' fax/telephone numbers. You can register up to 11 one-touch speed dialing keys,
which can include group dialing numbers.
NOTE
You can also register multiple fax/telephone numbers in each one-touch speed dialing key. (See "Registering
Group Dialing," on p. 3-4.)
3-1
Download from Www.Somanuals.com. All Manuals Search And Download.
1
2
3
4
Press [Menu].
Press [ (-)] or [ (+)] to select <ADD. REGISTRATION> ➞ press [OK].
Press [ (-)] or [ (+)] to select <1-TOUCH SPD DIAL> ➞ press [OK].
Press [ (-)] or [ (+)] to select a one-touch speed dialing key (01 to 11) ➞ press [OK] twice.
You can also select a key by pressing the one-touch speed dialing key.
5
Use the numeric keys to enter the fax/telephone number you want to register (max. 120 digits, including
spaces and pauses) ➞ press [OK] twice.
TEL NUMBER ENTRY
905xxxxxxx
NAME
:A
➞
3
6
Use the numeric keys to enter a name for the one-touch speed dialing key (max. 16 characters, including
spaces) ➞ press [OK].
NAME
Canon FRANCE
:A
[01]Canon FRANCE
➞
To continue registering one-touch speed dialing keys, repeat the procedure from step 4.
7
Press [Stop/Reset] to return to the standby display.
NOTE
Use the destination labels provided with the machine to label the one-touch speed dialing keys with the recipients'
names.
Changing or Deleting an Entry
■ Changing a Fax/Telephone Number You Registered
Follow steps 1 to 4 of "Registering One-Touch Speed Dialing" (see p. 3-1). In step 5, press and hold [Clear] to
delete an entire fax/telephone number ➞ use the numeric keys to enter a new number ➞ press [OK] ➞ [Stop/Reset].
NOTE
You can also press
[
(-)] or [Clear] repeatedly to delete the registered number.
■ Changing a Name You Registered
Follow steps 1 to 5 of "Registering One-Touch Speed Dialing" (see p. 3-1). In step 6, press and hold [Clear] to
delete an entire name ➞ use the numeric keys to enter a new name ➞ press [OK] ➞ [Stop/Reset].
NOTE
You can also press [Clear] repeatedly to delete the registered name.
3-2
Download from Www.Somanuals.com. All Manuals Search And Download.
■ Deleting an Entire Entry
Follow steps 1 to 4 of "Registering One-Touch Speed Dialing" (see p. 3-1). In step 5, press and hold [Clear] to
delete the registered number ➞ press [OK] ➞ [Stop/Reset].
NOTE
•
When deleting the registered number, the registered name is cleared automatically.
•
You can also press (-)] or [Clear] repeatedly to delete the registered number.
[
Registering Coded Speed Dialing
Before you can use coded speed dialing (see "Coded Speed Dialing," on p. 4-5), you need to register
the recipients' fax/telephone numbers. You can register up to 100 fax/telephone numbers.
3
1
2
3
4
Press [Menu].
Press [ (-)] or [ (+)] to select <ADD. REGISTRATION> ➞ press [OK].
Press [ (-)] or [ (+)] to select <CODED SPD DIAL> ➞ press [OK].
Press [ (-)] or [ (+)] to select a coded speed dialing code (00 to 99) ➞ press [OK] twice.
You can also select a code by pressing [Coded Dial] ➞ entering the two-digit code with the numeric keys.
5
Use the numeric keys to enter the fax/telephone number you want to register (max. 120 digits, including
spaces and pauses) ➞ press [OK] twice.
TEL NUMBER ENTRY
149xxxxxxx
NAME
:A
➞
6
Use the numeric keys to enter a name for the coded speed dialing code (max. 16 characters, including
spaces) ➞ press [OK].
NAME
Canon ITALIA
:A
CODED SPD DIAL
[∗ 00]Canon ITALIA
➞
To continue registering coded speed dialing codes, repeat the procedure from step 4.
7
Press [Stop/Reset] to return to the standby display.
3-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing or Deleting an Entry
■ Changing a Fax/Telephone Number You Registered
Follow steps 1 to 4 of "Registering Coded Speed Dialing" (see p. 3-3). In step 5, press and hold [Clear] to delete an
entire fax/telephone number ➞ use the numeric keys to enter a new number ➞ press [OK] ➞ [Stop/Reset].
NOTE
You can also press
[
(-)] or [Clear] repeatedly to delete the registered number.
■ Changing a Name You Registered
Follow steps 1 to 5 of "Registering Coded Speed Dialing" (see p. 3-3). In step 6, press and hold [Clear] to delete an
entire name ➞ use the numeric keys to enter a new name ➞ press [OK] ➞ [Stop/Reset].
3
NOTE
You can also press
[
(-)] or [Clear] repeatedly to delete the registered name.
■ Deleting an Entire Entry
Follow steps 1 to 4 of "Registering Coded Speed Dialing" (see p. 3-3). In step 5, press and hold [Clear] to delete the
registered number ➞ press [OK] ➞ [Stop/Reset].
NOTE
•
When deleting the registered number, the registered name is cleared automatically.
•
You can also press (-)] or [Clear] repeatedly to delete the registered number.
[
Registering Group Dialing
Before you can use group dialing (see "Group Dialing," on p. 4-5), you need to register the recipients'
fax/telephone numbers. You can register up to 110 groups, which can include one-touch speed dialing
keys and/or coded speed dialing codes.
Each time you program a one-touch speed dialing key or coded speed dialing code, the amount of
group dials available is reduced by one.
NOTE
•
You can only enter the fax/telephone numbers that have already been registered for one-touch or coded speed
dialing. See the following titles:
-
-
"Registering One-Touch Speed Dialing," on p. 3-1
"Registering Coded Speed Dialing," on p. 3-3
•
You cannot enter numbers with the numeric keys.
1
2
3
Press [Menu].
Press [ (-)] or [ (+)] to select <ADD. REGISTRATION> ➞ press [OK].
Press [ (-)] or [ (+)] to select <GROUP DIAL> ➞ press [OK].
3-4
Download from Www.Somanuals.com. All Manuals Search And Download.
4
5
Specify an empty one-touch speed dialing key or coded speed dialing code that you want to set as the
group dial.
●
●
To register a group under a one-touch speed dialing key:
❑
Press [ (-)] or [ (+)] to select a one-touch speed dialing key (01 to 11) ➞ press [OK] twice.
You can also select a key by pressing the one-touch speed dialing key.
To register a group under a coded speed dialing code:
Press [Coded Dial] ➞ use the numeric keys to enter the two-digit code (00 to 99) ➞ press [OK] twice.
❑
Select the speed dialing numbers you want to register in the group ➞ press [OK] twice.
The speed dialing number refers to the one-touch dialing number or coded speed dialing number under which the
fax/telephone number is programmed.
To enter in the group a number stored under a one-touch speed dialing key, press the desired one-touch speed
dialing key(s).
3
To enter a number stored under a coded speed dialing code, press [Coded Dial] ➞ enter the two-digit code for the
number using the numeric keys. For multiple entries, press [Coded Dial] between each entry.
NOTE
To review the numbers you have entered, press [ (-)] or [ (+)].
6
7
Use the numeric keys to enter a name for the group (max. 16 characters, including spaces) ➞ press [OK].
NAME
Canon group 2
:1
GROUP DIAL
[02] GROUP DIAL
➞
To continue registering other groups, repeat the procedure from step 4.
The name you enter here will appear in speed dialing lists.
Press [Stop/Reset] to return to the standby display.
Changing or Deleting an Entry
■ Deleting a Fax/Telephone Number from the Group
Follow steps 1 to 4 of "Registering Group Dialing" (see p. 3-4). In step 5, press [ (-)] or [ (+)] to display the
number you want to delete ➞ press and hold [Clear] ➞ press [OK] ➞ [Stop/Reset].
■ Adding a Fax/Telephone Number to the Group
Follow steps 1 to 4 of "Registering Group Dialing" (see p. 3-4). In step 5, simply enter the additional number as
explained.
■ Deleting an Entire Group
Follow steps 1 to 4 of "Registering Group Dialing" (see p. 3-4). In step 5, press [Clear] repeatedly until all numbers
are deleted ➞ press [OK] ➞ [Stop/Reset].
NOTE
When deleting all numbers, the registered group name is cleared automatically.
3-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Printing Speed Dialing Lists
You can print lists of the recipients registered for speed dialing. You may want to keep these lists near
the machine to refer to them when dialing.
1
2
3
4
Press [Menu].
Press [ (-)] or [ (+)] to select <REPORTS/LISTS> ➞ press [OK].
Press [ (-)] or [ (+)] to select <SPEED DIAL LIST> ➞ press [OK].
Press [ (-)] or [ (+)] to select the list you want to print ➞ press [OK].
You can select from the following:
3
-
-
-
<1-TOUCH LIST>
<CODED DIAL LIST>
<GROUP DIAL LIST>
Samples of the lists are shown below.
■ 1-TOUCH LIST
01/02 2005
10:32 FAX 1234567
CANON
001
************************
1-TOUCH LIST
***
***
************************
NO.
RECIPIENT ADDRESS
DESTINATION ID
ADAM BOOKS,CPA
JOHN BARRISTER
NATALIE SMITH
SEYMOUR GREEN
[
01]
02]
04]
03]
732 2233
761 1298
[
[
[
1
1
516 911 4411
914 438 3619
■ CODED DIAL LIST
01/02 2005
10:47 FAX 1234567
CANON
001
*****************************
CODED DIAL LIST
***
***
*****************************
NO.
RECIPIENT ADDRESS
DESTINATION ID
[
[
[
[
00]
01]
02]
03]
555 1234
14043333499
16172223322
312 538 4005
BILL
*
*
*
*
PEACHTREE,INC.
HUNT INVESTMENTS
LAKESIDE INC.
1
■ GROUP DIAL LIST
01/02 2005
10:07 FAX 1234567
CANON
001
***************************
GROUP DIAL LIST
***
***
***************************
[
05] CANON GROUP
[
[
[
[
01] 225 7823
02] 233 7766
00] 876 2398
01] 613 9076
CANON NY
CANON CA
CANON TX
CANON OH
*
*
3-6
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Sending Faxes
CHAPTER
This chapter describes the different ways to send faxes. It also explains how to adjust scan settings to improve the
image quality.
Sending Methods
There are two methods of sending faxes from the machine:
- Memory Sending
- Manual Sending
NOTE
•
You can also fax the documents from your computer. If you want to install the software for fax sending, see the
following:
-
-
"Install software," in the Set-Up Sheet
Chapter 1, "Installation," in the Software Guide
•
For details on how to send faxes from your computer, see Chapter 4, "PC Faxing (MF5750/MF5770 Models Only),"
in the Software Guide.
Memory Sending
You should normally use memory sending to send documents efficiently.
If <MEMORY FULL> is displayed, the machine cannot scan the documents. In this case, wait for the
NOTE
You can register a new fax job while the machine is waiting to redial the recipient's number automatically. For
details on how to set the machine to redial automatically, see "Automatic Redialing," on p. 4-6. You can store up to
20 fax jobs or approximately 256 pages * in the memory.
*
Based on the condition that the other party sends the fax by the LaserBase MF5750/MF5770. with Canon
Fax Standard Chart No. 1, standard mode.
1
2
Place the document on the platen glass or load it in the ADF ➞ press [FAX].
For details on the types of documents you can fax, their requirements, and how to place or load documents, see
Chapter 3, "Document Handling," in the User’s Guide.
Adjust any necessary settings for your document.
• Press [Image Quality] to select the fax resolution. (See "Adjusting the Image Quality (Fax Resolution)," on p.
4-3.)
• Press [Exposure] to select the scan density. (See "Adjusting the Exposure (Scan Density)," on p. 4-3.)
4-1
Download from Www.Somanuals.com. All Manuals Search And Download.
3
4
Dial the recipient's fax/telephone number.
For details on the different dialing methods, see "Dialing Methods," on p. 4-4.
Press [Start].
If you are using the ADF, the fax will be transmitted automatically.
If you are using the platen glass, you will be prompted when the page has been scanned. Place the next page (for
a multipage document) ➞ press [Start]. To start sending, after all the pages have been scanned, press [OK].
NOTE
To cancel memory sending, press [Stop/Reset].
You can also cancel sending using [Status Monitor]. (See Chapter 7, "Status Monitor," in the User’s Guide.)
Manual Sending
Use manual sending when you want to talk to the recipient before sending a document, or if the
recipient does not have a fax machine that can receive automatically.
4
NOTE
•
You will need to connect a telephone to the machine if you want to talk to the recipient before sending a document.
You cannot use the platen glass for manual sending.
•
1
2
Connect a telephone to the machine if you want to talk to the recipient before sending a document.
For details on how to connect a telephone to the machine, see "Connect telephone cable," in the Set-Up Sheet.
Load the document in the ADF ➞ press [FAX].
For details on the types of documents you can fax, their requirements, and how to load documents, see Chapter
3, "Document Handling," in the User’s Guide.
3
Adjust any necessary settings for your document.
• Press [Image Quality] to select the fax resolution. (See "Adjusting the Image Quality (Fax Resolution)," on p.
• 4P-r3e.s)s [Exposure] to select the scan density. (See "Adjusting the Exposure (Scan Density)," on p. 4-3.)
4
5
Press [Hook] or pick up the handset of your telephone.
Dial the recipient's fax/telephone number.
For details on the different dialing methods, see "Dialing Methods," on p. 4-4.
NOTE
You cannot use group dialing for manual sending.
6
Talk through the handset to the recipient.
If you press [Hook] in step 4, you can pick up the handset when you hear the recipient’ voice.
If you hear a high-pitched signal instead of the recipient's voice, go to step 8.
4-2
Download from Www.Somanuals.com. All Manuals Search And Download.
7
8
Ask the recipient to set his fax machine to receive faxes.
When you hear a high-pitched signal, press [Start] ➞ hang up the handset.
NOTE
•
To cancel manual sending, press [Stop/Reset].
If the offhook alarm starts beeping, make sure that the handset is resting properly on the handset cradle. The
offhook alarm can be turned off. (See <4. OFFHOOK ALARM> of "Menu Descriptions," on p. 8-2.)
•
Improving Faxed Images
There are several settings that allow you to improve the quality of faxed documents.
Adjusting the Image Quality (Fax Resolution)
You can adjust the image quality (fax resolution) of the document you send. The higher the image
quality, the better the output quality at the other end, but the longer the transmission time. Adjust the
image quality according to the type of document you are sending.
4
1
2
Press [Image Quality].
Press [ (-)] or [ (+)] to select the resolution ➞ press [OK].
You can select from the following:
-
-
-
-
<STANDARD> for most text-only documents. (203x98 dpi)
<FINE> for fine-print documents (the resolution is twice that of <STANDARD>). (203x196 dpi)
<PHOTO> for documents that contain photographs (the resolution is twice that of <STANDARD>). (203x196 dpi)
<SUPER FINE> for documents that contain fine print and images (the resolution is four times that of
<STANDARD>). (203x391 dpi)
-
<ULTRA FINE> for documents that contain fine print and images (the resolution is eight times that of
<STANDARD>). (406x391 dpi)
Adjusting the Exposure (Scan Density)
Density is the degree of differences between light and dark areas of an image.
1
2
Press [Exposure].
Press [ (-)] or [ (+)] to adjust the density ➞ press [OK].
EXPOSURE
-LT
01/02 2005 TUE 15:10
FaxOnly
➞
DK+
STANDARD
You can select from the following:
-
-
-
Set in the middle for standard documents
Press [ (+)] for light documents to be darker
Press [ (-)] for dark documents to be lighter
4-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Dialing Methods
There are several ways of dialing the fax/telephone number of the party to which you want to send a
fax. They are as follows:
■ When the Fax/Telephone Number Is Not Registered in the Machine
• Regular Dialing
• Redialing
■ When the Fax/Telephone Number Is Registered in the Machine
• One-Touch Speed Dialing
• Coded Speed Dialing
• Group Dialing
• Directory Dialing
4
NOTE
•
If you are unsure of the registered fax/telephone number, check the destination labels, or print each list and check
the numbers. (See "Printing Speed Dialing Lists," on p. 3-6.)
•
•
For details on registering a fax/telephone number for speed dialing, see Chapter 3, "Speed Dialing."
The machine must be set to the Fax mode when dialing and your fax document must be loaded in the ADF or on
the platen glass.
Regular Dialing
When you come to a step that requires dialing a number, you can dial the number with the keys on the
numeric keypad, just like you would when dialing a telephone number.
1
Dial a fax/telephone number with the numeric keys.
NOTE
•
If you enter a wrong number, press
the digits you entered.
[
(-)] or [Clear] to delete the last digit. Or press and hold [Clear] to delete all
•
If <TIME OUT> in the <TX SETTINGS> is set to <ON>, scanning starts when you press [OK] after entering the
fax/telephone number.
2
Press [Start] to scan the document.
Press [OK] to start dialing when you set the document on the platen glass. When you set the document in the
ADF, the machine automatically starts dialing after scanning is complete.
One-Touch Speed Dialing
1
Press the desired one-touch speed dialing key (01 to 11).
The number registered under that one-touch speed dialing key is displayed.
<NOT REGISTERED> appears if no fax/telephone number is assigned to the one-touch speed dialing key you
pressed.
If <TIME OUT> in the <TX SETTINGS> is set to <ON>, scanning starts automatically.
NOTE
If you press a wrong key, press [Stop/Reset].
2
Press [Start] to scan the document.
Press [OK] to start dialing when you set the document on the platen glass. When you set the document in the
ADF, the machine automatically starts dialing after scanning is complete.
4-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Coded Speed Dialing
1
Press [Coded Dial] ➞ enter the desired two-digit code (00 to 99) with the numeric keys.
The number registered under that coded speed dialing code is displayed.
<NOT REGISTERED> appears if no fax/telephone number is assigned to the coded speed dialing code you entered.
If <TIME OUT> in the <TX SETTINGS> is set to <ON>, scanning starts automatically.
NOTE
If you enter a wrong code, press [Stop/Reset].
2
Press [Start] to scan the document.
Press [OK] to start dialing when you set the document on the platen glass. When you set the document in the
ADF, the machine automatically starts dialing after scanning is complete.
Group Dialing
4
1
Press the desired one-touch speed dialing key (01 to 11), or press [Coded Dial] ➞ enter the two-digit code
(00 to 99) to which a group of fax/telephone numbers are assigned.
The name of the group is displayed.
<NOT REGISTERED> appears if no fax/telephone number is assigned to the one-touch speed dialing key you pressed.
If <TIME OUT> in the <TX SETTINGS> is set to <ON>, scanning starts automatically.
NOTE
•
If you press a wrong key, press [Stop/Reset].
You cannot enter an unregistered fax/telephone number directly into a group.
•
2
Press [Start] to scan the document.
Press [OK] to start dialing when you set the document on the platen glass. When you set the document in the
ADF, the machine automatically starts dialing after scanning is complete.
Directory Dialing
Directory dialing allows you to look up the other party’s name you registered and retrieve the number for
dialing. This feature is convenient when you know the other party’s name but cannot recall the one-touch
speed dialing key, the code for coded speed dialing, or group dialing where the number is registered.
1
2
Press [Directory].
<NOT REGISTERED> appears if there are no numbers registered, and the display returns to dial entry mode.
Press a numeric key to enter the first letter of the name of the party you are searching for.
For example, if you want to search for a name that starts with the letter "H", press 4 (GHI) twice.
Entries starting with the letter you entered are displayed.
If the entry does not appear for the key you pressed, the entry is not registered for speed dialing. Dial the other
party's fax/telephone number with the numeric keys, (See "Regular Dialing," on p. 4-4.) or register the fax/
telephone number. (See Chapter 3, "Speed Dialing.")
• To check registered names
Pressing [ (+)] displays the names of other parties in alphabetical order.
Pressing [ (-)] displays them in reverse order.
When you reach the last name, the display returns to the first name.
3
4
With the name you want to dial displayed, press [OK].
The other party’s name, or the name for group dialing appears.
If <TIME OUT>in the <TX SETTINGS> is set to <ON>, scanning starts automatically .
Press [Start] to scan the document.
Press [OK] to start dialing when you set the document on the platen glass. When you set the document in the
ADF, the machine automatically starts dialing after scanning is complete.
4-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Redialing a Busy Number
There are two methods of redialing:
- Manual Redialing
- Automatic Redialing
Manual Redialing
Press [Redial/Pause] to redial the last number entered with the numeric keys used to send a fax.
NOTE
•
•
•
To cancel manual redialing, press [Stop/Reset].
The last number entered with the numeric keys will be deleted when you unplug and plug the power cord.
The number entered for a voice call is not stored for redial number.
4
Automatic Redialing
When using memory sending to send a document and the recipient's line is busy, the machine will
redial the number after an interval.
The machine allows you to customize automatic redialing settings to suit your needs. (See
"Customizing Automatic Redialing Settings" ‘on p.4-6.)
NOTE
To cancel automatic redialing, wait until the machine starts redialing ➞press [Stop/Reset]
➞
follow the instructions
in the LCD.
You can also cancel automatic redialing using [Status Monitor]. (See Chapter 7, "Status Monitor," in the User’s
Guide.)
■ Customizing Automatic Redialing Settings
You can customize the following settings:
• Whether or not the machine redials automatically
• The number of times the machine redials
• The time interval between redialing
1
2
3
4
5
Press [Menu].
Press [ (-)] or [ (+)] to select <FAX SETTINGS> ➞ press [OK].
Press [ (-)] or [ (+)] to select <TX SETTINGS> ➞ press [OK].
Press [ (-)] or [ (+)] to select <AUTO REDIAL> ➞ press [OK].
Press [ (-)] or [ (+)] to select <ON> to enable automatic redialing or <OFF> to disable it.
If you selected <OFF>:
●
❑
Press [OK].
4-6
Download from Www.Somanuals.com. All Manuals Search And Download.
●
If you selected <ON>:
❑
❑
Press [OK] twice.
Press [ (-)] or [ (+)], or use the numeric keys to enter the number of times you want the machine to redial ➞
press [OK] twice.
You can set the machine to redial between 1 to 10 times.
REDIAL TIMES
REDIAL INTERVAL
➞
2TIMES
2MIN.
❑
Press [ (-)] or [ (+)], or use the numeric keys to enter the time interval between redialing ➞ press [OK].
You can set the time interval between 2 to 99 minutes.
REDIAL INTERVAL
TX SETTINGS
4.TIME OUT
➞
4MIN.
6
Press [Stop/Reset] to return to the standby display.
4
(Sequential Broadcasting)
The machine allows you to send the same document to a maximum of 112 recipients in one operation.
NOTE
If you frequently send documents to the same group of recipients, you can group these numbers for group dialing.
This will allow you to send documents to all recipients in the group at the press of one or a few keys.
1
2
Place the document on the platen glass or load it in the ADF ➞ press [FAX].
For details on how to place or load documents, see Chapter 3, "Document Handling," in the User’s Guide.
Adjust any necessary settings for your document.
• Press [Image Quality] to select the fax resolution. (See "Adjusting the Image Quality (Fax Resolution)," on p.
4-3.)
• Press [Exposure] to select the scan density. (See "Adjusting the Exposure (Scan Density)," on p. 4-3.)
3
Enter the fax/telephone numbers you want to send to.
●
●
To use one-touch speed dialing:
❑
Press the one-touch speed dialing key(s). You can dial up to 11 destinations.
To use coded speed dialing:
Press [Coded Dial] ➞ use the numeric keys to enter the two-digit code. You can dial up to 100 destinations.
❑
NOTE
Repeat the step above to enter the other codes if necessary.
4-7
Download from Www.Somanuals.com. All Manuals Search And Download.
●
●
To use regular dialing:
❑
Use the numeric keys to enter the fax/telephone number ➞ press [OK]. You can dial up to one destination.
Press [Redial/Pause] to redial the last number dialed with the numeric keys.
To use directory dialing:
❑
❑
❑
Press [Directory].
Press a numeric key which contains the first letter of the desired destination.
Press [ (-)] or [ (+)] to scroll through the required names until you find the desired destination ➞ press
[OK].
NOTE
•
After entering the first one-touch speed dialing key or coded speed dialing code, you have 5 seconds to enter
another speed dialing key or code before the machine begins sending automatically. If you have entered more
than one speed dialing button or code, the machine waits for 10 seconds before it begins sending. If you do not
want the machine to send automatically, you need to change <TIME OUT> in <TX SETTINGS> in <FAX
SETTINGS> of the Menu. (See <4. TIME OUT> of "Menu Descriptions," on p. 8-5.)
4
•
To review the numbers you have entered, press [ (-)] or [ (+)].
4
After you have specified all of the destinations, press [Start].
If you are using the platen glass, you will be prompted when the page has been scanned. Place the next page (for
a multipage document) ➞ press [Start]. To start sending, press [OK].
NOTE
•
Regardless of the order you used when dialing, the machine sends the document to the destinations you specified
in this order: regular dialing numbers, one-touch speed dialing numbers, then coded speed dialing numbers.
Only one broadcasting job will be active at any given time.
•
•
To cancel sending, press [Stop/Reset]
➞
follow the instructions in the LCD. When you press [Stop/Reset], sending
to all recipients will be canceled. You cannot cancel sending to only one recipient. (See Chapter 7, "Status
Monitor," in the User’s Guide.)
Special Dialing
This section explains special dialing features, such as dialing an overseas number, and switching
temporarily to tone dialing.
Dialing an Overseas Number (With Pauses)
When you dial or register an overseas number, you may need to insert a pause within the number.
NOTE
You cannot insert a pause after the last number you entered for manual sending.
1
Place the document on the platen glass or load it in the ADF ➞ press [FAX].
For details on the types of documents you can fax, their requirements, and how to place or load documents, see
Chapter 3, "Document Handling," in the User’s Guide.
4-8
Download from Www.Somanuals.com. All Manuals Search And Download.
2
3
Adjust any necessary settings for your document.
• Press [Image Quality] to select the fax resolution. (See "Adjusting the Image Quality (Fax Resolution)," on p.
4-3.)
• Press [Exposure] to select the scan density. (See "Adjusting the Exposure (Scan Density)," on p. 4-3.)
Use the numeric keys to dial the international access code.
For details on international access codes, contact your local telephone company.
NOTE
If you enter a wrong number, press
[
(-)] or [Clear] to delete the last digit. Or press and hold [Clear] to delete all
the digits you entered.
4
5
6
If necessary, press [Redial/Pause] to enter a two-second pause (P).
TEL=0P
4
For a longer pause, press [Redial/Pause] again for another two-second pause. Alternatively, you can change the
length of the pause. (See <2. PAUSE TIME> of "Menu Descriptions," on p. 8-4.)
Use the numeric keys to dial the country code, the area code, and the fax/telephone number of the other
party.
NOTE
•
If you enter a wrong number, press [Stop/Reset]
If you make a mistake, press
digits you entered.
➞
start again from step 3.
•
[
(-)] or [Clear] to delete the last digit. Or press and hold [Clear] to delete all the
Press [Start].
NOTE
•
To cancel sending after dialing has started, press [Stop/Reset]
To take advantage of the speed dialing features of the machine, register frequently used overseas numbers for
one-touch or coded speed dialing. (See Chapter 3, "Speed Dialing.")
➞
follow the instructions in the LCD.
•
Switching Temporarily to Tone Dialing
Many banks, airline, and hotels provide automated information services that require tone dialing. If the
machine is connected to a rotary pulse line, follow this procedure to set the machine temporarily for
tone dialing:
1
2
Press [FAX].
Press [Hook] or pick up the handset of your telephone.
NOTE
When using your telephone, you need to connect it to the machine. (See "Connect telephone cable," in the Set-Up
Sheet.)
4-9
Download from Www.Somanuals.com. All Manuals Search And Download.
3
4
Enter a destination using the numeric keys on your telephone or using a one-touch speed dialing key,
coded speed dialing code, [Redial/Pause], or the numeric keys on the machine.
When the recorded message of the information service answers, press [
When [ ] is pressed, <T> is displayed in the LCD.
If your telephone line uses tone dialing, go to the next step.
] to switch to tone dialing.
5
Use the numeric keys on the machine to enter the numbers requested by the information service.
Numbers entered after pressing [ ] will be dialed using tone dialing.
6
7
If you want to receive faxes, press [Start].
Hang up the handset to disconnect the call.
Tone dialing is canceled when you disconnect the call.
NOTE
4
If the offhook alarm starts beeping, make sure that the handset is resting properly on the handset cradle. The
offhook alarm can be turned off. (See <4. OFFHOOK ALARM> of "Menu Descriptions," on p. 8-2.)
4-10
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Receiving Faxes
CHAPTER
This chapter describes the different ways to receive faxes. It also explains how to set the receive mode and to cancel
the documents the machine is receiving.
Setting the Receive Mode
Follow this procedure to set the receive mode:
1
2
3
4
Press [Menu].
Press [ (-)] or [ (+)] to select <FAX SETTINGS> ➞ press [OK].
Press [ (-)] or [ (+)] to select <RECEIVE MODE> ➞ press [OK].
Press [ (-)] or [ (+)] to select the receive mode ➞ press [OK].
You can select from the following:
-
<FaxOnly> to automatically receive faxes, all calls will be answered as fax transmission. Voice calls will then be
disconnected. (See "Receiving Faxes Automatically: FaxOnly Mode," on p. 5-1.)
<FaxTel> to automatically switch between fax and voice calls. Faxes will be received automatically, and the
machine will ring for voice calls. (See "Receiving Both Faxes and Voice Calls Automatically: FaxTel Mode," on p.
5-2.)
-
-
-
<AnsMode> to receive faxes automatically and route voice calls to an answering machine connected to the
machine. (See "Receiving When an Answering Machine Is Connected: AnsMode," on p. 5-3.)
<Manual> for the connected telephone to ring for fax and voice calls. Fax calls must be answered manually.
(See "Receiving Faxes Manually: Manual Mode," on p. 5-4.)
NOTE
If you set <MAN/AUTO SWITCH> to <ON> in <FAX SETTINGS> of the Menu, the machine will receive faxes
automatically even when the receive mode is set to <Manual>. (See <4. MAN/AUTO SWITCH> of "Menu
Descriptions," on p. 8-6.)
5
Press [Stop/Reset] to return to the standby display.
NOTE
You can save the toner consumption when printing out the received documents. (See Chapter 10, “Machine
Settings,” in the User's Guide.)
Receiving Faxes Automatically: FaxOnly Mode
If you want to select <FaxOnly>, check the following:
■ Select This Mode If:
• you have a dedicated telephone line for fax use only.
• you only want to receive faxes automatically with the machine.
■ You Will Need to:
• set <FaxOnly>. (See "Setting the Receive Mode," on p. 5-1.)
• connect the machine to a dedicated telephone line. (See "Connect telephone cable," in the Set-Up Sheet.)
5-1
Download from Www.Somanuals.com. All Manuals Search And Download.
■ When You Receive a Fax Call
The machine will receive the fax automatically.
■ When You Receive a Voice Call
You will not be able to answer the call.
NOTE
•
If you connect a telephone to the machine and enable the <INCOMING RING> setting, the telephone will ring
when the machine receives a voice call, and then you can answer the call.
•
You can select the number of rings. (See <3. INCOMING RING> of "Menu Descriptions," on p. 8-5.)
Receiving Both Faxes and Voice Calls Automatically: FaxTel Mode
■ Select This Mode If:
• you only have one telephone line for both fax and telephone use.
• you want to receive faxes automatically as well as voice calls.
■ You Will Need to:
5
set <FaxTel>. (See “Setting the Receive Mode,” on p. 5-1.)
■ When You Receive a Fax Call
The machine will receive the fax automatically.
■ When You Receive a Voice Call
The machine will ring. Pick up the handset to answer the call.
Customizing FaxTel
You can customize this mode to control precisely how your machine handles incoming calls. You can
adjust the time the machine takes to check whether a call is a fax or voice call, the length of time the
machine rings when it is a voice call, and the action the machine must take if no one answers a voice
call.
Follow this procedure to customize <FaxTel>:
NOTE
We recommend you leave these settings on the default settings unless you have a particular need to change
them. Certain settings can affect your ability to receive faxes.
5-2
Download from Www.Somanuals.com. All Manuals Search And Download.
1
2
3
4
5
Press [Menu].
Press [ (-)] or [ (+)] to select <FAX SETTINGS> ➞ press [OK].
Press [ (-)] or [ (+)] to select <RX SETTINGS> ➞ press [OK].
Press [ (-)] or [ (+)] to select <FAX/TEL OPT. SET> ➞ press [OK] twice.
Press [ (-)] or [ (+)] to select the time 0 to 30 seconds that the machine takes to check whether a call is
fax or voice call ➞ press [OK] twice.
6
7
Press [ (-)] or [ (+)] to select the length of time 15 to 300 seconds that the machine rings when the call
is a voice call ➞ press [OK] twice.
Press [ (-)] or [ (+)] to select whether the machine switches to receive mode or disconnects the call if
no one answers a voice call after the specified time in step 6 ➞ press [OK].
You can select from the following:
5
-
-
<RECEIVE> to switch to receive mode
<DISCONNECT> to disconnect the call
8
Press [Stop/Reset] to return to the standby display.
Receiving When an Answering Machine Is Connected: AnsMode
If you want to select <AnsMode>, check the following:
■ Select This Mode If:
• you only have one telephone line for both fax and telephone use.
• you want to receive faxes automatically and receive voice messages on your answering machine.
■ You Will Need to:
• set <AnsMode>. (See "Setting the Receive Mode," on p. 5-1.)
• connect an answering machine to the machine. (See "Connect telephone cable," in the Set-Up Sheet.)
NOTE
Follow the guidelines below to adjust the answering machine:
-
-
-
Set the answering machine to answer on the first or second ring.
The entire message should be no longer than 15 seconds.
In the message, tell your callers how to send a fax.
■ When You Receive a Fax Call
The machine will receive the fax automatically.
5-3
Download from Www.Somanuals.com. All Manuals Search And Download.
■ When You Receive a Voice Call
The answering machine will record any voice messages.
Receiving Faxes Manually: Manual Mode
If you want to select <Manual>, check the following:
■ Select This Mode If:
• you only have one telephone line for both fax and telephone use.
• you receive mainly voice calls and sometimes faxes.
■ You Will Need to:
• set <Manual>. (See "Setting the Receive Mode," on p. 5-1.)
• connect a telephone to the machine. (See "Connect telephone cable," in the Set-Up Sheet.)
• make sure the <REMOTE RX> setting in the <RX SETTINGS> menu is enabled, if you want to start receiving a
document from the telephone. (See <5. REMOTE RX> of "Menu Descriptions," p. 8-6.)
■ When You Receive a Fax Call
The telephone will ring. Pick up the handset and if you hear a beep ➞ press [Start] on the machine to receive the
fax, or enter the two-digit ID code from the telephone ➞ hang up the handset.
5
NOTE
•
Receiving faxes entering two-digit ID code from the extension telephone can be used only on a touch tone line.
If the offhook alarm starts beeping, make sure that the handset is resting properly on the handset cradle. The
offhook alarm can be turned off. (See <4. OFFHOOK ALARM> of "Menu Descriptions," on p. 8-2.)
•
■ When You Receive a Voice Call
The telephone will ring. Pick up the handset to answer the call. If the caller wants to send a document after talking
to you, ask them to press the start key on their fax machine. When you hear a beep, press [Start] on the machine to
receive the fax ➞ hang up the handset.
NOTE
The telephone rings for every call, whether it is a fax call or a voice call. If you want the machine to receive faxes
automatically after ringing for a specified number of rings, enable the <MAN/AUTO SWITCH> setting. You can also
specify the number of rings before the machine receives faxes. (See <4. MAN/AUTO SWITCH> of "Menu
Descriptions," on p. 8-6.)
5-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Receiving Faxes While Performing Other Tasks
Since the machine is a multitasking device, it can receive faxes and voice calls while you are
performing other tasks.
• If you receive a fax while you are performing certain tasks, the machine stores the incoming fax in the
memory. Then, as soon as you finish your task, the machine automatically prints the fax. You can
receive a fax while performing the following tasks:
- Printing
- Scanning (Scan mode)*
- Printing reports or lists
- Copying
* Starts printing the fax as soon as the machine receives it, while performing these tasks.
• You cannot receive a fax while sending a fax.
5
Receiving Faxes in the Memory When a Problem Occurs
If the machine encounters a problem when it is receiving a fax, the machine automatically stores the
unprinted pages of the fax in the memory, and the LCD displays <RECEIVED IN MEMORY> as well as
one or more messages. When the problem is cleared, the machine automatically prints the fax which
was stored in the memory. For an explanation of the message(s) and details on the action to take, see
"LCD Messages," on p. 7-1.
NOTE
•
The machine memory can store up to 20 fax jobs or approximately 256 pages.*
*
Based on the condition that the other party sends the fax by the LaserBase MF5750/MF5770 with Canon
Fax Standard Chart No. 1, standard mode. The maximum number of pages that the machine's memory can
store differs depending on the other party's machine.
•
•
Once the pages are printed, they are deleted from the memory.
If the memory becomes full, you will not be able to receive the remaining pages. Contact the other party and ask
them to resend the remaining pages of the fax.
Canceling Receiving
Follow this procedure if you want to stop receiving a fax before reception is completed:
1
Press [Stop/Reset] in the Fax mode.
The confirmation message will appear.
CANCEL DURING TX/RX?
< YES
NO >
2
Press [ (-)] to cancel receiving.
If you change your mind and want to continue receiving, press [ (+)] for <NO>.
NOTE
You can also cancel receiving, by pressing [Status Monitor]. (See Chapter 7, "Status Monitor," in the User’s Guide.)
5-5
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Reports and Lists
CHAPTER
This chapter explains how to print out the transaction reports and the lists of settings and recipients registered in the
machine.
Summary of Reports and Lists
The table below shows the reports and lists that can be printed from the machine. Refer to the pages
indicated for more details.
Report or List
1-TOUCH LIST
Description
Details
p. 3-6
Lists the fax/telephone numbers and names registered for one-touch
speed dialing.
Lists the fax/telephone numbers and names registered for coded
speed dialing.
CODED DIAL LIST
GROUP DIAL LIST
p. 3-6
p. 3-6
Lists groups registered for group dialing.
Shows recent facsimile transactions performed by the machine.
ACTIVITY REPORT
You can enable or disable automatic printing of this report after every p. 6-2
20 transactions. You can also manually set the machine to print it.
Prints after transmission of a document.
TX (Transmission) REPORT
You can enable or disable this feature, or set the machine to print a
report only when an error occurs.
p. 6-3
Prints after reception of a document.
RX (Reception) REPORT
USER DATA LIST
You can enable or disable this feature, or set the machine to print a
report only when an error occurs.
p. 6-5
p. 6-6
Lists the current settings of the machine and the registered sender
information.
NOTE
•
The paper sizes that can be used for reports and lists function are A4 and letter. Only papers loaded in the
cassette can be used for reports and lists function.
•
You can cancel printing the reports or lists using [Status Monitor]. (See Chapter 7, "Status Monitor," in the User’s
Guide.)
6-1
Download from Www.Somanuals.com. All Manuals Search And Download.
ACTIVITY REPORT
Printing the ACTIVITY REPORT
By default, the machine is set to print an ACTIVITY REPORT after every 20 transactions.
Transactions in an ACTIVITY REPORT are listed chronologically.
01/02 2005 17:28 FAX 1234567
CANON
001
***************************
ACTIVITY REPORT
***
***
***************************
ST. TIME
DESTINATION TEL/ID
NO.
MODE
PGS.
RESULT
01/02 16:16
01/02 16:27
01/02 16:30
01/02 16:53
01/02 17:20
2 887 0166
5001
0001
0002
5002
0003
AUTO RX
MANUAL TX
ECM
ECM
ECM
ECM
ECM
4
1
1
1
0
OK
00'14
02'00
00'17
00'14
00'00
*
*
*
OK
OK
OK
NG
20 545 8545
03 3758 2111
1 432 2060
TRANSMIT
AUTO RX
TRANSMIT
0 STOP
01/02 17:20
1 234 2060
0004
TRANSMIT
ECM
0
NG
00'00
#0018
0
6
Transaction mode
Indicates an entry that
has appeared on a
previous report.
Error correction mode transaction
Number of page being sent or received
when an error occurred.
Error code
[Stop/Reset] was pressed during transaction
Transaction duration
Recipient fax/telephone
number/Registered name for
speed dial
Number of pages that have
been sent successfully
Transaction number
NOTE
The recipient's fax/telephone number (DESTINATION TEL/ID) is not shown for the manually sent faxes.
If you want to print an ACTIVITY REPORT manually, follow this procedure:
1
2
Press [Menu].
Press [ (-)] or [ (+)] to select <REPORTS/LISTS> ➞ press [OK] twice.
REPORTS/LISTS
1.ACTIVITY REPORT
6-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the ACTIVITY REPORT Setting
You can set the machine to turn on or off automatic printing of the ACTIVITY REPORT.
1
2
3
4
5
Press [Menu].
Press [ (-)] or [ (+)] to select <FAX SETTINGS> ➞ press [OK].
Press [ (-)] or [ (+)] to select <REPORT SETTINGS> ➞ press [OK].
Press [ (-)] or [ (+)] to select <ACTIVITY REPORT> ➞ press [OK].
Press [ (-)] or [ (+)] to select the setting you want ➞ press [OK].
You can select from the following:
-
-
<OUTPUT YES> to turn on automatic printing of the ACTIVITY REPORT
<OUTPUT NO> to turn off automatic printing of the ACTIVITY REPORT
6
Press [Stop/Reset] to return to the standby display.
Adjusting the TX REPORT Setting
6
The machine can print a TX (transmission) report (TX REPORT or ERROR TX REPORT) after sending
a document. You can set it to print every time it sends a document, or only when an error occurs.
Alternatively, you can disable printing the report. By default, the machine is set to print a TX report only
when an error occurs.
■ TX REPORT
01/02 2005 17:52 FAX 1234567
CANON
001
*********************
TX REPORT
***
***
*********************
TRANSMISSION OK
TX/RX NO
0004
RECIPIENT ADDRESS
DESTINATION ID
ST. TIME
1 432 2060
01/02 17:52
TIME USE
PAGES SENT
RESULT
00' 11
1
OK
6-3
Download from Www.Somanuals.com. All Manuals Search And Download.
■ ERROR TX REPORT
01/02 2005 17:21 FAX 1234567
CANON
001
***************************
ERROR TX REPORT
***
***
***************************
Error
description
TX FUNCTION WAS NOT COMPLETED
TX/RX NO
0005
RECIPIENT ADDRESS
DESTINATION ID
ST. TIME
20 545 8545
01/02 17:21
TIME USE
PAGES SENT
RESULT
00'0 0
0
NG
#
0018 BUSY/NO SIGNAL
OK: Transmission successful
NG: Some or no pages sent
Error code
Transaction number
Number of pages sent
Recipient fax/telephone number
Registered name for speed dial
6
Transmission duration
Transmission time
NOTE
The recipient's fax/telephone number (RECIPIENT ADDRESS) is not shown for the manually sent faxes.
1
2
3
4
5
Press [Menu].
Press [ (-)] or [ (+)] to select <FAX SETTINGS> ➞ press [OK].
Press [ (-)] or [ (+)] to select <REPORT SETTINGS> ➞ press [OK].
Press [ (-)] or [ (+)] to select <TX REPORT> ➞ press [OK].
Press [ (-)] or [ (+)] to select the setting you want ➞ press [OK].
You can select from the following:
-
-
-
<PRINT ERROR ONLY> to print a report only when a transmission error occurs
<OUTPUT YES> to print a report every time you send a document
<OUTPUT NO> to disable printing the report
●
If you selected <PRINT ERROR ONLY> or <OUTPUT YES>:
❑
You can set whether to print the first page of the fax under the report. Press [ (-)] or [ (+)] to select <OFF>
or <ON> ➞ press [OK].
-
-
<OFF> to print no first page
<ON> to print the first page
NOTE
Even if <REPORT WITH TX IMAGE> of <TX REPORT> setting is set to <ON>, the machine will not print the first
page of the fax when you fax the documents from your computer.
6
Press [Stop/Reset] to return to the standby display.
6-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the RX REPORT Setting
The machine can print an RX (reception) report after receiving a document. You can set it to print every
time it receives a document, or only when an error occurs. Alternatively, you can disable printing the
report. By default, the machine is set not to print an RX REPORT.
01/02 2005 17:52 FAX 1234567
CANON
001
*********************
RX REPORT
***
***
*********************
Description
RECEPTION OK
TX/RX NO
5003
RECIPIENT ADDRESS
905 795 1111
DESTINATION ID
ST. TIME
TIME USE
PGS.
01/02 17:52
00' 14
1
RESULT
OK
6
Transaction number
OK: Reception successful
NG: Some or no pages received
Senders fax/telephone number
Number of pages received.
If reception was not complete, it
indicates the number of page being
received when an error occurred.
Reception duration
Registered name for speed dial
(not mentioned on the RX report)
Reception time
1
2
3
4
5
Press [Menu].
Press [ (-)] or [ (+)] to select <FAX SETTINGS> ➞ press [OK].
Press [ (-)] or [ (+)] to select <REPORT SETTINGS> ➞ press [OK].
Press [ (-)] or [ (+)] to select <RX REPORT> ➞ press [OK].
Press [ (-)] or [ (+)] to select the setting you want ➞ press [OK].
You can select from the following:
-
-
-
<OUTPUT NO> to disable printing the report
<PRINT ERROR ONLY> to print a report only when a reception error occurs
<OUTPUT YES> to print a report every time you receive a document
6
Press [Stop/Reset] to return to the standby display.
6-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Printing the USER DATA LIST
The USER DATA LIST allows you to check the current settings of the machine as well as the registered
sender information. (See "Registering Sender Information," on p. 2-1.)
01/02 2005
13:36 FAX 1234567
CANON
001
****************************
USER'S DATA LIST
***
***
****************************
1. PAPER SETTINGS
CASSETTE
PAPER SIZE
PAPER TYPE
MP TRAY
A4
PLAIN PAPER
PAPER SIZE
PAPER TYPE
A4
PLAIN PAPER
2. COMMON SETTINGS
6
1
2
3
Press [Menu].
Press [ (-)] or [ (+)]] to select <REPORTS/LISTS> ➞ press [OK].
Press [ (-)] or [ (+)] to select <USER DATA LIST> ➞ press [OK].
REPORTS/LISTS
3.USER DATA LIST
6-6
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Troubleshooting
CHAPTER
This chapter describes the problems you might encounter during fax operations and their remedies. It also explains
what to do if you cannot solve the problem by yourself.
LCD Messages
The following messages are displayed in the LCD when the machine performs a function or if it
encounters an error.
This section describes messages related to fax functions. For other messages, see Chapter 9,
"Troubleshooting," in the User’s Guide.
CHANGE PAPERSIZE
Cause
When the machine prints the reports or lists, the paper size setting is set to a size other than <LTR>,
or <A4>.
Remedy
Set the paper size setting to <LTR>, or <A4> and load paper of the same size. For the TX report or
RX report, the machine automatically prints the report(s) which was stored in the memory.
CHECK DOCUMENT
Cause 1
Remedy
There is a paper jam in the ADF.
Remove the document you are trying to send in the ADF. (See Chapter 9, "Troubleshooting," in the
User’s Guide.)
Make sure that the document is not too long or too short. (See Chapter 3, "Document Handling," in
the User’s Guide.)
Cause 2
Remedy
The ADF roller rotates without feeding documents.
Fan the edge that will feed into the machine first, then tap the edge of multiple page documents on a
flat surface to even the stack.
7-1
Download from Www.Somanuals.com. All Manuals Search And Download.
CHECK PAPER SIZE
Cause
The size of the paper in the cassette or multi-purpose feeder is different from that of the paper
specified in <PAPER SIZE> in <PAPER SETTINGS> of the Menu.
Remedy 1
Load the correct paper size or change <PAPER SIZE> in <PAPER SETTINGS> of the Menu. For
more information, see the following:
• Chapter 2, "Paper Handling," in the User’s Guide
• Chapter 5, "Copying," in the User’s Guide
Then reset the machine by opening the front cover and then closing it.
Remedy 2
If you are trying to print a report or list, set the paper size setting to <LTR>, or <A4> and load paper
of the same size. Then reset the machine by opening the front cover and then closing it. The report
or list will then be printed automatically.
DOCUMENT TOO LONG
Cause
The document is longer than 1 m, or is not feeding correctly.
Remedy
Reduce the length of the document to within 1 m, and then re-send it.
MEM IN USE nn %
Cause
7
Shows the percentage of the memory currently in use. This message is displayed when you set the
document in ADF.
Remedy
If you need more space, wait for the machine to send any faxes in memory. Also print or delete any
documents in memory you no longer needed.
MEMORY FULL
Cause 1
The memory becomes full during sending, or receiving the fax.
Remedy
When sending the document, divide it into a few parts or select a lower fax resolution.
If you need more space, wait for the machine to send any remaining faxes.
If <MEMORY FULL> appears while scanning documents using the ADF, the document being
scanned stops in the ADF. In this case, clear the paper jam in the ADF. (See Chapter 9,
"Troubleshooting," in the User’s Guide. )
Cause 2
Remedy
The number of fax jobs can be stored in memory reached the maximum.
The machine can store up to 20 fax jobs for each sending and receiving job, or 25 fax jobs including
sending and receiving jobs. Wait for the machine to send any faxes in memory. Also print or delete
any documents in memory.
7-2
Download from Www.Somanuals.com. All Manuals Search And Download.
NOT REGISTERED
Cause
The one-touch speed dialing key or coded speed dialing code you entered is not registered.
Remedy
Register the one-touch speed dialing key or coded speed dialing code. For more information, see the
following:
• "Registering One-Touch Speed Dialing," on p. 3-1
• "Registering Coded Speed Dialing," on p. 3-3
RECEIVED IN MEMORY
Cause
The machine received the fax in the memory because paper or toner ran out, a paper jam occurred,
or incorrect paper size was loaded.
Remedy
Load correct paper size in the cassette, replace the cartridge, or clear the paper jam. For more
information, see the following:
• Chapter 2, "Paper Handling," in the User’s Guide
• Chapter 8, "Maintenance," in the User’s Guide
• Chapter 9, "Troubleshooting," in the User’s Guide
REMOVE MP PAPER
7
Cause
Paper is loaded in the multi-purpose feeder.
Remedy
Remove the paper from the multi-purpose feeder.
If the machine receives the fax or prints the reports and lists when paper is loaded in the
multi-purpose feeder, they will be stored in the memory.
Error Codes
Errors in reports are recorded as error code numbers because there is not enough space to print a
detailed description of the error in the report. When errors are recorded in reports, note the error code
number, and check it against the table below to learn more about what caused the error and how to
remedy it.
#0001
Cause
There may be a document jam.
Clear the jam.
Remedy
7-3
Download from Www.Somanuals.com. All Manuals Search And Download.
#0003
Cause 1
A document longer than one foot is being sent from the feeder.
Remedy
Cause 2
Divide the document into pages and resend from the platen glass.
Data is too large and taking too long to send a document.
Remedy
Cause 3
Reduce the scan resolution and resend.
It’s taking too long to receive a page.
Remedy
#0005
Contact the other party and have them reduce the scan resolution or split the document into
segments and resend.
Cause 1
Remedy
The other party’s fax machine did not respond within 35 seconds.
Send the document again. Contact the other party and have them check their fax machine. If you are
making an overseas call, add pauses to the registered number.
7
Cause 2
Remedy
The other party is not using a G3 fax machine.
Check with the other party, and send the document to a G3 fax machine. If the other party does not
have a G3 fax machine, try sending your document using a transmission mode that the other party
supports.
#0009
Cause
No paper is loaded in the cassette or the cassette is not set properly.
Load paper in the cassette or set the cassette properly.
Remedy
#0012
Cause
The other fax machine has run out of paper and its memory is full.
Contact the other party, and tell them to refill their paper cassette.
Remedy
7-4
Download from Www.Somanuals.com. All Manuals Search And Download.
#0018
Cause
The other fax did not respond to redialing. The document was not sent because the other fax
machine was busy and did not respond within 55 seconds.
Remedy
#0037
Wait for a while and try again. If you still cannot send the document, contact the other party and have
them check if their fax machine is turned on. If the line is busy, wait more and try again.
Cause
The memory is full.
Remedy
Print out the faxes received in the memory.
#0046
Cause
A fax was sent from the fax machine with no TSI (Transmitting Subscriber Identification) signal, used to
identify the sending fax machine. when <RX RESTRICTION> is set to <ON>.
Remedy
#0995
Set <RX RESTRICTION> to <OFF>, to receive all faxes sent.
7
Cause
A waiting fax job has been canceled.
Resend the fax if needed.
Remedy
Faxing Problems
Sending Problems
You cannot send a fax.
Q
A
Is the machine overheated?
Unplug the machine and let it cool for about 5 minutes. Then plug in the machine and try sending
again.
Q
A
Q
A
Did you connect the power cord to the machine just now?
Wait for a while. After connecting the power cord, the machine cannot scan documents immediately.
Is the machine set for the correct telephone line type (pulse/tone)?
Make sure the machine is set for the correct telephone line type. (See "Setting the Telephone Line
Type," on p. 2-3.)
7-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Q
A
Is the document loaded?
Remove the document, stack it if necessary, and place it on the platen glass or load it in the ADF
correctly. For more information, see Chapter 3, "Document Handling," in the User’s Guide.
Q
A
Is the one-touch speed dialing key or coded speed dialing code you entered registered for the
feature you want to use?
Check the one-touch speed dialing key or coded speed dialing code and make sure it is registered
correctly. (See Chapter 3, "Speed Dialing.")
Q
A
Q
A
Did you dial a correct number? Or have you been provided with an incorrect number?
Is the energy saver mode off?
The machine does not scan documents, if it is in the energy saver mode. To restore the machine
from the energy saver mode, press [Energy Saver].
Q
A
Q
A
Does the other party's fax machine have enough paper?
Call the other party and ask them to make sure paper is loaded in their fax machine.
Did an error occur during sending?
7
Print an ACTIVITY REPORT and check for an error. (See "Printing the ACTIVITY REPORT," on p.
6-2.)
Q
A
Is the telephone line working properly?
Make sure there is a dial tone when you pick up the handset of the telephone connected to the
machine. If there is no dial tone, contact your local telephone company.
Q
A
Q
Is the receiving fax machine a G3 fax machine?
Make sure the receiving fax machine is compatible with the machine (which is a G3 fax machine).
The other party's telephone may be busy or the other party's fax machine may be turned off. Is
BUSY/NO SIGNAL shown on the ERROR TX REPORT?
A
A
The fax/telephone number you dialed is busy. Try sending the document later.
The other party's fax machine is not working. Contact the other party and have them check their fax
machine.
7-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Q
A
Did the receiving fax machine answer within 55 seconds (after all automatic redialing attempts)?
Contact the other party and have them check their fax machine. For an overseas call, add pauses to
the registered number. (See "Dialing an Overseas Number (With Pauses)," on p. 4-8.)
Q
A
Is the In Use/Memory indicator lighting?
The In Use/Memory indicator may light, which means the extension phone is busy. Please wait until
the extension phone becomes free.
Faxes sent from the machine are spotted or dirty.
Q
A
Is the sending fax machine working properly?
Check the machine by making a copy. For more information, see Chapter 5, "Copying," in the User’s
Guide.
If the copy is clear, the problem may be in the receiving fax machine. If the copy is spotted or dirty,
clean the platen glass or the read area of the platen glass. For more information, see Chapter 8,
"Maintenance," in the User’s Guide.
Q
A
Is the document loaded?
7
Remove the document, stack it if necessary, and place it on the platen glass or load it in the ADF
Cannot send using ECM (Error Correction Mode).
Q
A
Does the receiving fax machine support ECM?
If the receiving fax machine does not support ECM, the document is sent in the normal mode without
error checking.
Errors occur frequently while sending.
Q
A
Are the telephone lines in proper condition? Or do you have a good connection?
Lower the transmission speed. (See <3. TX START SPEED> of "Menu Descriptions," on p. 8-2.)
7-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Receiving Problems
Cannot receive a fax automatically.
Q
A
Is the machine set to receive automatically?
For the machine to receive faxes automatically, the receive mode must be set to <FaxOnly>, <Fax/
If you set <MAN/AUTO SWITCH> to <ON> in <FAX SETTINGS> of the Menu, the machine will
receive faxes automatically even when the receive mode is set to <Manual>. (See <4. MAN/AUTO
SWITCH> of "Menu Descriptions," on p. 8-6.)
Q
A
Is the machine's memory full?
Wait for the machine to finish any fax or print jobs stored in the memory. Then ask the other party to
resend the fax.
Q
A
Did an error occur during reception?
6-2.) You can also check the RX REPORT when it is printed automatically. (See "Adjusting the RX
REPORT Setting," on p. 6-5.)
7
Q
A
Is the telephone line connected properly?
Make sure all line connections are secure. (See "Connect telephone cable," in the Set-Up Sheet.)
Q
A
Is the machine set to switch automatically between telephone and fax receptions?
For the machine to switch automatically, the receive mode must be set to <AnsMode>. (See Chapter
5, "Receiving Faxes.")
Confirm that an answering machine is connected to the machine and that it is turned on with an
outgoing message properly recorded.
Q
A
Is the sending fax machine able to send the CNG signal that tells the machine that the incoming
signal is a fax?
Some fax machines cannot send the CNG signal that tells the machine the incoming call is a fax.
In such cases, you will have to receive the fax manually. (See "Receiving Faxes Manually: Manual
Mode," on p. 5-4.)
7-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Cannot receive a document manually.
Q
A
Is the machine set to receive manually?
For the machine to receive faxes manually, the receive mode must be set to <Manual>. (See Chapter
5, "Receiving Faxes".)
Q
A
Did you press [Start], or dial the remote receiving ID after hanging up the handset?
Always press [Start], or dial the remote receiving ID before hanging up the handset. Otherwise you
will disconnect the call.
Print quality is poor.
Q
A
Are you using the correct type of paper?
Make sure you load paper that meets the paper requirements for the machine. For more information,
see Chapter 5, "Copying," in the User’s Guide.
Q
A
Is the sending fax machine functioning properly?
7
The sending fax machine usually determines the fax's quality. Call the sender and have them make
sure the scanning glass of their fax machine is clean.
Q
A
Is the machine in the toner saver mode?
Set <TONER SAVER MODE> to <OFF> in <COMMON SETTINGS> of the Menu. (See Chapter 10,
"Machine Settings," in the User’s Guide.)
Faxes do not print.
Q
A
Is the cartridge installed properly?
Make sure the cartridge is installed properly. For more information, see Chapter 8, "Maintenance," in
the User’s Guide.
Q
A
Is the sealing tape removed from the cartridge?
Remove the sealing tape from the toner cartridge. (See "Install cartridge," in the Set-Up Sheet.)
7-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Q
A
Is any toner left in the cartridge?
Replace the cartridge with a new one. For more information, see Chapter 8, "Maintenance," in the
User’s Guide.
A
Select <KEEP PRINTING> in <TONER SUPPLY LOW> in <RX SETTINGS> in <FAX SETTINGS> of
the Menu. With this setting, the machine will not store documents in the memory even if the toner
has run out. (See <7. TONER SUPPLY LOW> of "Menu Descriptions," on p. 8-6.)
Q
A
Is the correct paper loaded in the cassette?
Make sure paper is loaded in the cassette. For more information, see Chapter 2, "Paper Handling,"
in the User’s Guide.
A
Load the correct paper size or change <PAPER SIZE> in <PAPER SETTINGS> of the Menu. For
more information, see the following:
• Chapter 2, "Paper Handling," in the User’s Guide
• Chapter 5, "Copying," in the User’s Guide
Faxed images are blotched or uneven.
Q
A
Are the telephone lines in proper condition? Or do you have a good connection?
7
ECM (Error Correction Mode) for sending/receiving should eliminate such problems. However, if the
telephone lines are in poor condition, you may have to try again. Then call the sender to resend the
document.
Q
A
Is the sending fax machine functioning properly?
The sending fax machine usually determines the fax's quality. Call the sender and have them make
sure the scanning glass of their fax machine is clean.
Cannot receive a fax using ECM (Error Correction Mode).
Q
A
Does the sending fax machine support ECM?
If the sending fax machine does not support ECM, the document is received in the normal mode
without error checking.
7-10
Download from Www.Somanuals.com. All Manuals Search And Download.
Errors occur frequently while receiving.
Q
A
Q
A
Are the telephone lines in proper condition? Or do you have a good connection?
Lower the reception speed. (See <4. RX START SPEED> of "Menu Descriptions," on p. 8-2.)
Is the sending fax machine functioning properly?
Call the sender and have them check that their fax machine is functioning properly.
Telephone Problems
You cannot dial.
Q
A
Q
A
Is the telephone line connected properly?
Make sure all line connections are secure. (See "Connect telephone cable," in the Set-Up Sheet.)
Is the machine set for the correct telephone line type (pulse/tone)?
7
Make sure the machine is set for the correct telephone line type. (See "Setting the Telephone Line
Type," on p. 2-3.)
The telephone disconnects while you are talking.
Q
A
Is the telephone line connected in securely?
Check that the telephone cables are connected securely to the jacks on the machine, the telephone
jack on your wall and the jack on your telephone. (See "Connect telephone cable," in the Set-Up
Sheet.)
7-11
Download from Www.Somanuals.com. All Manuals Search And Download.
If a Power Cut Occurs
If power is suddenly lost due to an outage or accidental unplugging, a built-in battery retains the user
data settings and the speed dialing settings. Any sent or received documents stored in the memory are
backed up for about 3 minutes.
During a power cut, functions are limited as follows:
• You cannot send, receive, copy, scan, or print documents.
• You may not be able to make telephone calls using a telephone connected to the machine,
depending on the type of telephone you use.
• You can receive telephone calls using a telephone connected to the machine depending on the type
of telephone you use.
If You Cannot Solve the Problem
If you have a problem with the machine and you cannot solve it by referring to the information in this
chapter and Chapter 9, "Troubleshooting," in the User’s Guide, contact your local authorized Canon
dealer or the Canon help line.
7
7-12
Download from Www.Somanuals.com. All Manuals Search And Download.
8
Machine Settings
CHAPTER
This chapter explains how to adjust machine settings. The list of all the settings is also provided for your reference.
Accessing the Machine Settings
1
2
Press [Menu].
Press [ (-)] or [ (+)] to select the menu you want to change ➞ press [OK].
You have now accessed the settings in the USER DATA LIST.
3
Press [ (-)] or [ (+)] to select the sub menu you want to change ➞ press [OK].
NOTE
•
•
•
•
For details on sub menus, see "Menu Descriptions" on p.8-1.
If you press [Stop/Reset] before [OK] is pressed, the item you have selected will not be registered.
Press [Stop/Reset] to exit from Menu.
If you press [Menu], the display returns to the previous display.
Menu Descriptions
NOTE
•
•
•
Before changing settings, print the USER DATA LIST to check the current settings. (See "Printing the USER DATA
LIST," on p. 6-6.)
For details on <PAPER SETTINGS>, <COMMON SETTINGS>, <COPY SETTINGS>, <PRINTER SETTINGS>,
and <TIMER SETTINGS>, see Chapter 10, "Machine Settings," in the User
’s Guide.
For details on <NETWORK SETTING>, see Chapter 3, “Appendix,” in the Network Guide.
FAX SETTINGS
Name
Descriptions
1. RECEIVE MODE
Sets how the machine receives fax and telephone calls.
FaxOnly
answered as fax transmission. Voice calls will then be
disconnected.
FaxTel
The machine automatically switches between fax and
voice calls. Fax will be received automatically, and the
machine will ring for voice calls.
AnsMode
Manual
The machine receives documents automatically and the
answering machine records voice calls.
The connected telephone rings when the machine
receives both fax and voice calls. Fax calls must be
answered manually. If <MAN/AUTO SWITCH> is set to
<ON>, faxes can be received automatically. (See <4.
MAN/AUTO SWITCH> of “Menu Descriptions,” on
p. 8-6)
8-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Name
2. USER SETTINGS
Descriptions
The basic operation settings in the Fax mode can be
specified.
1. TEL LINE SETTINGS
1. UNIT TEL NUMBER
Specifies the telephone line settings.
Your fax/telephone number can be registered within 20
digits, including spaces. (See "Registering Your Fax/
Telephone Number and Name," on p. 2-2.)
2. TEL LINE TYPE
Selects the telephone line type. (See "Setting the
Telephone Line Type," on p. 2-3.)
TOUCH TONE
ROTARY PULSE
The telephone line is set for touch tone dialing.
The telephone line is set for rotary pulse dialing.
3. TX START SPEED
Sets the transmission speed for all documents you
send.
33600bps/14400bps/9600bps/7200bps/4800bps/
2400bps
4. RX START SPEED
2. UNIT NAME
Sets the transmission speed for all documents you
receive.
33600bps/14400bps/9600bps/7200bps/4800bps/
2400bps
You can register your name or your company name
within 24 characters, including spaces. (See
"Registering Your Fax/Telephone Number and Name,"
on p. 2-2.)
8
3. TX TERMINAL ID
Sets the options for the sender Information.
ON
Sender information will be printed in small type at the
top of each page.
1. TTI POSITION
Selects whether the sender Information is positioned
inside or outside the image area.
OUTSIDE IMAGE: Terminal ID is printed outside the
image border.
INSIDE IMAGE: Terminal ID is printed inside the image
border.
2. TEL NUMBER MARK
You can prefix your number with the abbreviations FAX
or TEL in your sender information.
OFF
Sender information will not be printed.
4. OFFHOOK ALARM
Enables/disables the offhook alarm that alerts you when
the handset is not in the handset cradle.
ON
The offhook alarm sounds when the handset of
extension telephone is left off the hook.
OFF
No offhook alarm.
5. R-KEY SETTING
The R-KEY setting allows you to set how the fax
connects to PBX. If your fax machine is not connected
through a PBX, you can ignore these settings.
PSTN
The fax is connected to the outside line.
PBX
The fax is connected through a PBX. Select one of the
following settings, depending on the type of PBX in
service. Two settings are available: HOOKING, PREFIX
8-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Name
Descriptions
6. RX RESTRICTION
Sets whether to receive a fax by detecting the TSI
(Transmitting Subscriber Identification) signal, used to
identify the sending fax machine.
OFF
All receptions are conducted.
ON
Receives the fax only from the sending fax machine that
sends the TSI signal.
3. REPORT SETTINGS
1. TX REPORT
Sets the settings related to report functions.
Enables/disables automatic printing of a transmission
report.
PRINT ERROR ONLY
Prints a report only when a transmission error occurs.
REPORT WITH TX IMAGE Enables/disables printing of the first page of the fax
under the report.
OFF
ON
No first page is printed.
Prints the first page.
OUTPUT YES
Prints a report every time you send a document.
REPORT WITH TX IMAGE Enables/disables printing of the first page of the fax
under the report.
8
OFF
ON
No first page is printed.
Prints the first page.
No report is printed.
OUTPUT NO
2. RX REPORT
Enables/disables automatic printing of a reception
report.
OUTPUT NO
No report is printed.
PRINT ERROR ONLY
Prints a report only when a reception error occurs.
Prints a report every time you receive a document.
OUTPUT YES
3. ACTIVITY REPORT
Enables/disables automatic printing of a transaction
report after every 20 transactions.
OUTPUT YES
Prints a report automatically after every 20 transactions.
No ACTIVITY REPORT is printed.
OUTPUT NO
8-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Name
Descriptions
4. TX SETTINGS
1. ECM TX
Sets the transmission functions.
The ECM (Error Correction Mode) transmission is
turned on or off.
ON
All transmissions are conducted with ECM if the other
party's fax supports ECM.
OFF
ECM is turned off.
2. PAUSE TIME
Sets the length of the pause you insert into a dialing
sequence.
1SEC to 15SEC (4SEC)
3. AUTO REDIAL
Sets whether to perform automatic redial when the
other line is busy or no answer.
ON
Customizes the redial operation.
1. REDIAL TIMES
Sets the number of retries.
1TIMES to 10TIMES (2TIMES)
2. REDIAL INTERVAL
Sets period of time between redialing.
2MIN. to 99MIN. (2MIN.)
OFF
After the first attempt at dialing fails, redialing is not
attempted.
8
8-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Name
Descriptions
4. TIME OUT
ON
Enables/disables automatic scanning of documents
after the fax number is entered.
Scanning begins automatically in 5 or 10 seconds after
you enter the fax number.
OFF
Press [Start] to scan document. Otherwise, AUTO
CLEAR function activates and the LCD returns to
standby display after 1 minute. (See Chapter 10,
"Machine Settings," in the User's Guide.)
5. RX SETTINGS
1. ECM RX
Sets the reception functions.
The ECM (Error Correction Mode) reception is turned
on or off.
ON
All receptions are conducted with ECM if the other
party's fax supports ECM.
OFF
ECM is turned off.
2. FAX/TEL OPT. SET
If you select <FaxTel> as the receive mode, customizes
its settings.
1. RING START TIME
Selects the time the machine takes to check whether a
call is a fax or voice call.
0SEC to 30SEC (8SEC)
8
2. F/T RING TIME
Selects the ring length for voice calls.
15SEC to 300SEC (22SEC)
3. F/T SWITCH ACTION
Selects whether the machine switches to receive mode
after the ring time has elapsed, or whether if
disconnects the call.
RECEIVE, DISCONNECT
3. INCOMING RING
Sets whether the telephone rings when it receives a
voice call, enabling you to answer the call. This function
is only available when the fax receive mode is set to
<FaxOnly>.
OFF
The telephone does not ring when it receives a voice
call.
ON
The telephone rings when it receives a voice call if a
telephone is connected.
RING COUNT
Sets the number of incoming rings. The telephone will
be disconnected after the specified times.
1TIMES to 99TIMES (2TIMES)
8-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Name
Descriptions
4. MAN/AUTO SWITCH
Sets whether the machine switches to the document
receive mode after the connected extension telephone
rings for a specified length of time in the manual receive
mode.
ON
The machine switches to document receive mode after
the connected extension telephone rings for a specified
time.
F/T RING TIME
Sets the length of time to elapse before the machine
switches to the document receiving.
1SEC to 99SEC (15SEC)
OFF
The connected extension telephone keeps ringing until
someone answers the call manually.
5. REMOTE RX
ON
Enables/disables remote receiving.
The machine enables remote receiving.
REMOTE RX ID
You can dial code on the remote extension to start
receiving a document.
A combination of two characters using 0 to 9,
and #
is possible. The default character is 25.
OFF
The machine disables remote receiving.
Receives images at a reduced size.
Image reduction is turned on.
8
6. RX REDUCTION
ON
1. RX REDUCTION
AUTO SELECTION: Reducing size is set automatically.
FIXED REDUCTION: Reducing size is preset.
97%, 95%, 90%, 75%
2. SELECT REDUCE DIR
VERTICAL ONLY: Reduction is performed in the
vertical direction only.
HORIZ & VERTICAL: Reduction is performed in the
horizontal and vertical direction.
OFF
Image reduction is turned off.
7. TONER SUPPLY LOW
Allows you to set how the machine responds when the
toner supply is low.
RX TO MEMORY
The machine receives all documents in the memory.
KEEP PRINTING
The keep printing function is turned on. With this
setting, the machine will not store documents in the
memory if the toner has run out. Re-set to <RX TO
MEMORY> after replacing the cartridge with a new one.
8-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Name
Descriptions
6. SYSTEM SETTINGS
Sets the functions of FAX DEFAULT, and COUNTRY
SELECT.
1. FAX DEFAULT
Sets the default for the fax functions.
Sets the scan density.
1. SCAN DENSITY
STANDARD
DK
Suitable for standard documents.
Suitable for light documents.
LT
Suitable for dark documents.
2. RESOLUTION
STANDARD
FINE
Sets the fax resolution.
Suitable for most text-only documents.
Suitable for fine-print documents.
Suitable for documents that contains photographs.
PHOTO
SUPER FINE
Suitable for documents that contain fine print and
images. (The resolution is four times that of
STANDARD)
ULTRA FINE
Suitable for documents that contain fine print and
images. (The resolution is eight times that of
STANDARD)
8
2. COUNTRY SELECT*
Selects the country where you are using your machine.
UK/GERMANY/FRANCE/ITALY/SPAIN/HOLLAND/
DENMARK/NORWAY/SWEDEN/FINLAND/AUSTRIA/
BELGIUM/SWITZERLAND/PORTUGAL/IRELAND/
GREECE/LUXEMBOURG/HUNGARY/CZECH/
RUSSIA/SLOVENIA/SOUTH AFRICA/POLAND/
OTHERS
(The factory default setting is in bold face.)
* This setting is available only for some countries.
8-7
Download from Www.Somanuals.com. All Manuals Search And Download.
ADD. REGISTRATION
Name
Descriptions
1. 1-TOUCH SPD DIAL
Registers the information on one-touch speed dialing.
(See "Registering One-Touch Speed Dialing," on p.
3-1.) Up to 11 destinations can be registered.
1. TEL NUMBER ENTRY
2. NAME
Registers the other party's fax/telephone number (max.
120 digits, including spaces).
Registers the other party's name (max. 16 characters,
including spaces).
2. CODED SPD DIAL
Registers the information on coded speed dialing. (See
"Registering Coded Speed Dialing," on p. 3-3.) Up to
100 destinations can be registered.
1. TEL NUMBER ENTRY
2. NAME
Registers the other party's fax/telephone number (max.
120 digits, including spaces).
Registers the other party's name (max. 16 characters,
including spaces).
3. GROUP DIAL
Registers the information on group dialing. (See
"Registering Group Dialing," on p. 3-4.) Up to 110
destinations can be registered.
1. TEL NUMBER ENTRY
2. NAME
Registers the other party's fax/telephone numbers by
specifying the one-touch speed dialing keys or coded
speed dialing codes.
8
Registers the other party's name (max. 16 characters,
including spaces).
REPORTS / LISTS
Name
Descriptions
1. ACTIVITY REPORT
Prints a report manually before it is printed automatically
after every 20 transactions.
2. SPEED DIAL LIST
Prints the list of the fax/telephone numbers registered for
one-touch speed dialing keys, coded speed dialing
codes, or group dialing.
1-TOUCH LIST, CODED DIAL LIST, GROUP DIAL LIST
3. USER DATA LIST
Prints out a list of items set or registered in the Menu.
8-8
Download from Www.Somanuals.com. All Manuals Search And Download.
9
Appendix
CHAPTER
This chapter lists the specifications for the fax function of the machine, and the index.
Specifications
Specifications are subject to change without notice.
Facsimile
Applicable Line
Public Switched Telephone Network (PSTN)
Compatibility
G3
Data Compressing System
MH, MR, MMR, JBIG
33.6/31.2/28.8/26.4/24/21.6/19.2/16.8/14.4/12/9.6/7.2/4.8/2.4 Kbps
Automatic fallback
Modem Speed
Approx. 3 seconds/page* at 33.6 Kbps, ECM-JBIG, transmitting from the
memory
Transmission Speed
* Based on ITU-T No. 1 Chart, Standard Mode.
Transmission: Maximum approx. 256 pages*
Transmission/Reception Memory Reception: Maximum approx. 256 pages*
* Based on ITU-T No. 1 Chart, Standard Mode.
0.8 msec/line*
Fax Scanning Speed
* Based on ITU-T No. 1 Chart.
STANDARD: 8 pels/mm x 3.85 lines/mm
FINE: 8 pels/mm x 7.7 lines/mm
Fax Resolution
PHOTO: 8 pels/mm x 7.7 lines/mm
SUPER FINE: 8 pels/mm x 15.4 lines/mm
ULTRA FINE: 16 pels/mm x 15.4 lines/mm
9-1
Download from Www.Somanuals.com. All Manuals Search And Download.
• Speed dialing
One-touch speed dialing (11 destinations)
Coded speed dialing (100 destinations)
Group dialing (110 destinations)
Dialing
Directory dialing (with Directory key)
• Regular dialing (with numeric keys)
• Automatic redialing
• Manual redialing (with Redial/Pause key)
• Sequential broadcast (112 destinations)
• Automatic reception
• Remote reception by telephone (Default ID: 25)
• ACTIVITY REPORT (after every 20 transactions)
• TX (Transmission)/RX (Reception) REPORT
• TTI (Transmit Terminal Identification)
Networking
Telephone
Connection
Telephone/answering machine (CNG detecting signal)
9
9-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
Symbols
(–),
(+) keys, 1-2
Numerics
1-TOUCH LIST
description, 6-1
printing, 3-6
sample, 3-6
adjusting, 4-3
key, 1-2
1-TOUCH SPD DIAL setting, 8-8
FAX key, 1-2
A
ACTIVITY REPORT
description, 6-1, 8-3, 8-8
printing, 6-2
setting, 6-3
Alarm indicator, 1-2
FAX/TEL OPT. SET setting, 8-5
ANS. MACHINE MODE, 5-3
AUTO REDIAL setting, 8-4
C
CHECK DOCUMENT message, 7-1
CHECK PAPER SIZE message, 7-2
Clear key, 1-2
printing, 3-6
GROUP DIAL setting, 8-8
Group dialing
Coded Dial key, 1-1
description, 3-1
CODED DIAL LIST
description, 6-1
printing, 3-6
CODED SPD DIAL setting, 8-8
Coded speed dialing
changing, deleting, 3-4
description, 3-1
registering, 3-3
using, 4-5
adjusting, 4-3
key, 1-2
COUNTRY SELECT settings, 8-7
Customer support, 1-1
In Use indicator, 1-1
INCOMING RING setting, 8-5
D
K
Date and Time, entering, 2-2
KEEP PRINTING setting, 8-6
Dialing
Keys (See also individual key names), 1-1
coded speed, 3-1, 3-3, 4-5
group, 3-1, 3-4, 4-5
methods, 4-4
one-touch speed, 3-1, 4-4
regular, 4-4
L
LCD, 1-2
LCD messages (See also individual messages), 7-1
DOCUMENT TOO LONG message, 7-2
9-3
Download from Www.Somanuals.com. All Manuals Search And Download.
coded speed dialing, 3-3
M
Machine settings, 8-1
MAN/AUTO SWITCH setting, 8-6
MANUAL MODE, 5-4
Manual sending, 4-2
MEMORY FULL message, 7-2
Memory sending, 4-1
Menu
fax/telephone number/name, 2-1
group dialing, 3-4
one-touch speed dialing, 3-1
REMOTE RX setting, 8-6
Reset key, 1-2
descriptions, 8-1
key, 1-2
RING START TIME setting, 8-5
R-KEY SETTING setting, 8-2
ROTARY PULSE setting, 8-2
N
NOT REGISTERED message, 7-3
Numeric keys, 1-2
O
OFFHOOK ALARM setting, 8-2
RX REDUCTION setting, 8-6
OK key, 1-2
One-touch speed dialing
RX TO MEMORY setting, 8-6
changing, deleting, 3-2
description, 3-1
keys, 1-1
registering, 3-1
using, 4-4
Overseas number, dialing, 4-8
9
P
description, 2-1
Pause key, 1-1
PAUSE TIME setting, 8-4
Pauses, dialing with, 4-8
Problems
receiving, 7-8
sending, 7-5
telephone, 7-11
Sequential broadcasting, 4-7
R
RECEIVE MODE settings, 8-1
Receive Mode settings, 5-1
RECEIVED IN MEMORY message, 7-3
Receiving
coded, 3-1, 3-3
lists, 3-6
methods, 3-1
one-touch, 3-1
automatically, 5-1
canceling, 5-5
in memory when a problem occurs, 5-5
manually, 5-4
problems, 7-8
Standby display, 1-3
Start key, 1-2
when an answering machine is connected, 5-3
while performing other tasks, 5-5
Status Monitor key, 1-2
Stop/Reset key, 1-2
Receiving Both Faxes and Voice Calls Automatically
FaxTel Mode, 5-2
Support, customer, 1-1
SYSTEM SETTINGS settings, 8-7
REDIAL INTERVAL setting, 8-4
REDIAL TIMES setting, 8-4
Redialing
automatically, 4-6
manually, 4-6
9-4
Download from Www.Somanuals.com. All Manuals Search And Download.
T
TEL LINE SETTINGS setting, 8-2
TEL LINE TYPE setting, 8-2
TEL NUMBER MARK setting, 8-2
Telephone line type setting, 2-3
Telephone problems, 7-11
TIME OUT setting, 8-5
Time, entering, 2-2
TOUCH TONE setting, 8-2
Troubleshooting, 7-1
TTI POSITION setting, 8-2
TX (Transmission) REPORT
description, 6-1, 8-3
setting, 6-3
TX REPORT setting, 8-3
TX SETTINGS settings, 8-4
TX START SPEED setting, 8-2
TX TERMINAL ID setting, 8-2
U
UNIT NAME setting, 8-2
UNIT TEL NUMBER setting, 8-2
USER DATA LIST
description, 6-1
printing, 6-6
9
USER DATA LIST setting, 8-8
USER SETTINGS settings, 8-2
9-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Memo
Download from Www.Somanuals.com. All Manuals Search And Download.
CANON INC.
30-2, Shimomaruko 3-chome, Ohta-ku, Tokyo 146-8501, Japan
CANON U.S.A., INC.
One Canon Plaza, Lake Success, NY 11042, U.S.A.
CANON CANADA INC.
6390 Dixie Road Mississauga, Ontario L5T 1P7, Canada
CANON EUROPA N.V.
Bovenkerkerweg 59-61 P.O. Box 2262, 1180 EG Amstelveen, The Netherlands
CANON FRANCE S.A.
17, quai du President Paul Doumer 92414 Courbevoie Cedex, France
CANON (U.K.) LTD.
Woodhatch, Reigate, Surrey, RH2 8BF, United Kingdom
CANON DEUTSCHLAND GmbH
Europark Fichtenhain A10, 47807 Krefeld, Germany
CANON ITALIA S.p.A.
Via Milano, 8-20097 San Donato Milanese (MI) Italy
CANON LATIN AMERICA, INC.
703 Waterford Way, Suite 400, Miami, Florida 33126, U.S.A.
CANON AUSTRALIA PTY. LTD
1 Thomas Holt Drive, North Ryde, Sydney, N.S.W. 2113, Australia
CANON CHINA CO., LTD
15F, North Tower, Beijing Kerry Centre, 1 Guang Hua Road, Chao Yang District,
100020, Beijing, China
CANON SINGAPORE PTE. LTD.
1 HarbourFront Avenue #04-01 Keppel Bay Tower Singapore 098632
230V
CANON HONGKONG CO., LTD
19/F., The Metropolis Tower, 10 Metropolis Drive, Hunghom, Kowloon, Hong Kong
© CANON INC. 2005
FA7-7224 (000)
032004 NF
PRINTED IN JAPAN OR CHINA
Download from Www.Somanuals.com. All Manuals Search And Download.
|