Canon Camera Accessories 3552B002 User Manual

TS-E17mm f/4L  
TS-E24mm f/3.5L II  
ENG  
Instructions  
Download from Www.Somanuals.com. All Manuals Search And Download.  
a Safety Precautions  
Handling Cautions  
a Safety Precautions  
If the lens is taken from a cold environment into a  
warm one, condensation may develop on the lens  
surface and internal parts. To prevent condensation  
in this case, first put the lens into an airtight plastic bag  
before taking it from a cold to warm environment. Then  
take out the lens after it has warmed gradually. Do the  
same wn taking the lens from a warm environment  
into a coone.  
Do not look at the sun or a bright light source  
through the lens or camera. Doing so could result in  
loss of vision. Looking at the sun directly through the  
lens is especially hazardous.  
Whether it is attached to the camera or not, do not  
leave the lens under the sun without the lens cap  
attached. This is to prevent the lens from concentrating  
the sun’s rays, which could cause a fire.  
Do noe the lens in excessive heat such as in a  
in diresunlight. High temperatures can cause  
lens to alfunction.  
To mount/detach the lens, always move the tilt and  
shift scales to “0”. Fingers may get caught, or the  
camera may be damaged.  
When you tilt or shift the lens, sharp portions of
tilt or shift mechanism are exposed and care s
be taken to avoid touching these portions.  
Do not operate the shift function whiloperating
rotation function. You may be injured bhaving your  
fingers caught.  
ENG-2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
a Safety Precautions  
This device complies with Part 15 of the FCC Rules. Operation is  
subject to the following two conditions: (1) This device may not  
cause harmful interference, and (2) this device must accept any  
interference received, including interference that may cause  
undesired operation.  
Do not make any changes or modifications to the equipment  
unless otherwise specified in the instructions. If such changes or  
modifications should be made, you could be required to stop  
operation of e equipment.  
This equipmehas been tested and found to comply with the  
limits for B digital device, pursuant to part 15 of the FCC  
These its are designed to provide reasonable protection  
harmful erference in a residential installation. This  
ent generates, uses and can radiate radio frequency  
engy and, if not installed and used in accordance with the  
instrtions, may cause harmful interference to radio  
communications.  
However, there is no guarantee that interference will not occur in  
a particular installation. If this equipment does cause harmful  
interference to radio or television reception, which can be  
determined by turning the equipment off and on, the user is  
encouraged to try to correct the interference by one or more of  
the following measures:  
Countermeasures for harmful rays  
The TS-E17mm f/4L has a wide angle of view, and the  
lens protrudes from the front frame, so it can be  
affected by harmful rays. To prevent flare and ghosting,  
cutting off the harmful rays entering the lens with a piece  
of cardboard is recommended.  
Cutting off harmful rays is also recommended for TS-  
E24mm f/3.5L II, by using both the hood and the method  
used for TS-E17mm f/4L.  
Conventions used in this instruction  
Warning to prevent lens or camera malfun
or damage.  
Supplementary notes on using te lens and  
taking pictures.  
• Reorient or relocate the receiving antenna.  
• Increase the separation between the equipment and receiver.  
• Consult the dealer or an experienced radio/TV technician for  
help.  
This Class B digital apparatus complies with Canadian ICES-003.  
ENG-3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Nomenclature  
Tilt index  
Infrared index (15)  
11  
1:3.5  
24mm  
Distance index  
TS-E  
ft  
LENS  
m
Distance scale (8, 15)  
5
3
3
4
1
4
2
0.7  
11  
CANON  
1.5  
22  
0.5  
Tilt scale  
1.2  
0.4  
1
Depth-of-Field scale (15)  
0.3  
0.25  
0.8  
Lens mount index (8)  
0 . 7  
Tilt knob (10)  
Contacts  
Shift knob (6, 12)  
Shift index  
Shift scale  
For detailed information, reference page numbers are provided in parentheses (**).  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ENG-4  
Nomenclature  
Tilt index  
Tilt lock knob (10)  
Tilt-lock button (10)  
Tilt scale  
Focusing ring (8)  
Hood mount (17)  
Shift index  
TS-E17mm f/4L  
Rotation lock release  
button (13)  
TS rotation lock release  
button (14)  
Shift scale  
Lens  
Shift lock knob (12)  
Filter mounting thread (18)  
Lens cap mount (7)  
For detailed information, reference page numbers are provided in parentheses (**).  
ENG-5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
About the Shift Knob Cap  
Shifting will be easier if the supplied shift knob cap is mounted (p.4).  
However, for EOS cameras with built-in flash, the cap will come in contact with the camera during  
the lens’ mounting/detaching, or during shift/rotation operation. The shift knob cap is recommended  
for use with EOS-1, EOS-1D, EOS-1Ds, and EOS 5D series.  
Mounting screw  
(Length 3mm)  
emove knob  
crew.  
Mount the cap by squeezing it into  
the shift knob, and then fix it using  
the supplied screw.  
To remove the cap, remove the  
screw and pull out the cap.  
The screw (length 2.2mm) originally in the shift knob cannot be used to  
keep the shift knob cap in place. Always use the supplied screw.  
Shift knob cap  
Use a watchmaker's screwdriver (Phillips head type) to remove or mount  
screws.  
ENG-6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Mounting/Removing the Lens Cap  
(TS-E17mm f/4L)  
The lens of TS-E17mm f/4L protrudes from the front frame. To protect the lens, keep it covered with  
the exclusive lens cap when not shooting.  
2 4 m m  
T S - E  
m m  
1 7  
T S -
L E S  
N
O
C A N  
Removing  
ttaching  
To remove the cap, hold down the button on the
and turn the cap in the direction of the row until t
position mark on the cap aligns with the ed dot.  
To aach the cap, align the cap’s attachment position  
mark with the red dot on the front of the lens, then  
turn the cap as shown by the arrow until the lens’ red  
dot is aligned with the cap’s stop position mark.  
The removed lens cap can be hooked on the tripod  
using the supplied strap.  
Do not use the strap to lift the lens while the lens  
cap is attaching the lens. The lens may fall and  
break.  
ENG-7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1. Mounting and Detaching the Lens 2. Focusing  
See your camera’s instructions for details on  
mounting and detaching the lens.  
2 4 m m  
- E  
T S  
m m  
2 4  
T S - E  
L E N S  
C A N O
s a TE lens by turning the focusing ring.  
s cannbe taken using the auto focus.)  
When mounting or detaching the lens, always  
ensure that the tilt and shift scales are set t
“0” position.  
After detaching the lens, place the nwith
rear end up to prevent the lens suace and  
contacts from getting scratched.  
After using tilt or shift, readjust the focus.  
The distance scale is only valid when the tilt  
scale is set to the “0” position.  
If the contacts get soiled, scratched, r ha
fingerprints on them, corrosion or faulty  
connections can result. The camera and lens  
may not operate properly.  
For cameras which allow Live View shooting,  
focusing using the LCD monitor’s magnified image  
is recommended.  
If the contacts get soiled or have fingerprints on  
them, clean them with a soft cloth.  
If you remove the lens, cover it with the dust  
cap. To attach it properly, align the lens mount  
index and the index of the dust cap, and turn  
clockwise. To remove it, reverse the order.  
ENG-8  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3. Tilt Function  
Tilting inclines the lens relative to the image plane. When the tilt scale is set to the “0” position, the  
focusing and imaging planes are parallel. However, tilting puts the focusing plane at an angle to the  
imaging plane.  
Example 1  
Example 2  
To shoot so that all of an extensive subject is in focus, you must normally use a small aperture to  
obtain a large depth of field. But tilting allows you to keep all of the subject in focus even when there  
is insufficient depth of field (Example 1). Or, by tilting in the opposite direction, you can focus on a  
specific part of the subject (Example 2).  
ENG-9  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using Tilt  
A
2 4 m m  
T S - E  
m m  
2 4  
T S - E  
L E N S  
C A N O N  
B
Slide the tilt-lock button in the direction of  
arrow A. Loosen the tilt lock knob by turning  
it in the direction of arrow B.  
Turn the tilt knob to adjust the amount of tilt.  
Focus the shot by turning the focusing ring.  
To keep the tilt scale locked in the “0” position, slide  
the tilt lock button in the direction of “LOCK”, then turn  
the tilt lock knob in the direction of the arrow shown in  
Step 3.  
When you tilt the lens, sharp portions of the tilt  
mechanism are exposed and care should be  
taken to avoid touching these portions.  
Turn the tilt lock knob in the direction of the  
arrow to lock the amount of tilt for the shot.  
ENG-10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4. Shift Function  
Shifting moves the optical axis of the lens in parallel off the center of the imaging plane.  
Shift can be used to good effect in the situations shown below.  
If you photograph a subject such as a  
building with a normal lens, the top of  
the building tapers away. But by placing  
the camera parallel to the building and  
shifting the lens, you can correct this  
tapering effect.  
When you are shooting a reflective  
subject, you can move the camera to a  
position where the camera does not  
appear in the shot and then use shift to  
take the picture. This lets you keep the  
camera out of the shot without having  
to change the shot composition.  
ENG-11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using Shift  
2 4 m m  
- E  
T S  
m m  
2 4  
T S - E  
L E N
C A N O N  
Loosen the shift lock knob  
by turning it in the direction  
of the arrow.  
Turn the shift ko adjt  
the amount of ocus  
the shournithe  
focusi
Turn the shift lock knob in  
the direction of the arrow to  
lock the amount of shift for  
the shot.  
When you shift the lens, sharp portns of the schanism are exposed and care should be taken to  
avoid touching these portions. For ES camas with built-in flash, there may be contact with the lens while  
you operate the shift function.  
With large amounts of shift, the amounts of peripheral light at the top and bottom or left and right sides of  
the screen may differ, so shooting with a small aperture is recommended.  
The shift operation will be easier if the supplied cap is mounted on the shift knob (p.6).  
ENG-12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5. Rotation  
The rotation function enables you to change the direction of tilt or  
shift by rotating the tilt-shift mechanism.  
With the lens mounted on the camera, push the rotation lock release  
button towards the mount and then turn the tilt-shift mechanism.  
The rotation mechanism can be rotated through ±90°. The lens clicks every  
30° and locks in place in the 90° position.  
When rotating the lens, set te tilt and shift scales to the “0” position.  
Note that rotating the tilt-smechanism quickly while pressing on the  
rotation lock reltton my cause the shift lock knob to strike your  
fingers.  
Do not the hift function while operating the rotation function.  
You med having your fingers caught.  
FoEOs with built-in flash, there may be contact with the lens  
while you e the rotation function.  
In oto prevent shifts in position while shooting, shooting while  
rotation is locked, or shooting per click position is recommended.  
ENG-13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Changing the Operation Direction of Tilt and Shift (TS rotation Function)  
By using the TS rotation function,  
the relationship of the tilt and shift’s  
operation direction can switch from  
right angle to parallel.  
Press the TS rotation lock release  
button in the mounting direction while  
the lens is mounted on the camera,  
and then turn the tilt component.  
When the tilt and shift are used in a parallel direction,  
vignetting will occur in the areas marked in gray in the  
following table.  
TS-E17mm f/4L  
TS-E24mm f/3.5L II  
Tilt amount (Degree(s))  
Tilt and Shift direction  
Imaging Area  
8.5  
8
6.5  
6
7
5
6
4
5
3
4
3
2
6
7
8
9
10 11 12  
4
5
6
7
8
9
10 11 12  
Shift amount (mm)  
8.5  
8
6.5  
6
7
5
6
4
5
3
4
6
7
8
9 10 11 12  
8
9
10 11 12  
8.5  
8
6.5  
6
7
There are clicks at the 45° position, and  
will be fixed in either the right angle or  
parallel position.  
5
6
4
5
4
3
7
8
9
10 11 12  
3
2
4
5
6
7
8
9
10 11 12  
In order to prevent shifts in position while shooting, shooting  
while TS rotation is locked, or shooting per click position is  
recommended.  
ENG-14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6. Depth-of-Field Scale  
7. Infrared Index  
(TS-E24mm f/3.5L II)  
(TS-E24mm f/3.5L II)  
ft  
m
ft  
m
1.5  
2
3 5  
1.5  
2
3 5  
4 0.5 0.7 1 3  
0.5 0.7 1 3  
22 11 4 4 11 22  
22 11 4 4 11 22  
The depth of field is the distance in front of and  
behind the plane of focus on the subject th
appears sharp. The depth of field is indicat
the area between the depth-of-field scale lin
below the distance scale.  
frared ndex corrects the focus setting  
wn using monochrome infrared film. Focus on  
the ubject in MF, then adjust the distance  
setting by moving the focusing ring to the  
corresponding infrared index mark.  
Some EOS cameras cannot use infrared film. See  
the instructions for your EOS camera.  
The depth-of-field scale is only valid wthe  
tilt scale is set to the “0” position.  
The depth-of-field scale is an approximate  
indicator.  
The infrared index position is based on a  
wavelength of 800 nm.  
Be sure to observe the manufacturer’s  
instructions when using infrared film.  
Use a red filter also when you take the picture.  
ENG-15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8. TS-E Tripod Adapter  
(Sold Separately)  
9. Exposure  
With some camera models, the tilt, shift and  
rotation functions cannot be used when the  
camera is mounted directly on a tripod. When  
Shots can be taken using AE (automatic  
exposure) as long as the tilt and shift scales are  
set to the “0” position.  
this happens, fit the optional TS-E tripod adapter The use of AE is not recommended when the  
into the tripod mount socket on the camera  
before mounting the camera on the tripod.  
lens is tilted or shifted as exposure errors may  
result. It is recommended that you use the  
exposure values when the tilt and shift scales  
are set to he “0” position as a guide and then  
take the ot with as many exposure settings as  
ble.  
ENG-16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
10. Hood  
(TS-E24mm f/3.5L II)  
The EW-88B lens hood can keep unwanted light out of the lens, and also protects the lens from  
rain, snow, and dust.  
To attach the hood, align the hood’s attachment  
2 4 m m  
position mark with the red dot on the front of the lens,  
T S - E  
m m  
2 4  
- E  
T S  
then turn the hood as shown by the arrow until the lens’  
L E N S  
C A N O N  
red dot is aligned with the hood’s stop position mark.  
2 4 m m  
- E  
T S  
2
The hood cn be reverse-mounted on the lens for  
T S - E  
L E N S  
C A N O N  
storage
When attaching or detaching the hod, gasp of the hood to turn it. To prevent deformation, do not  
grasp the rim of the hood to turn it.  
Cutting off harmful rays entering the ley using both a hood as well as a piece of cardboard is  
recommended.  
A hood is not available for TS-E17mm f/4L.  
ENG-17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
11. Filters  
(Sold Separately)  
12. Infinity Compensation Mark  
(TS-E24mm f/3.5L II)  
(TS-E24mm f/3.5L II)  
Infinity compensation mark  
You can attach filters to the filter mounting  
thread on the front of the lens.  
Only one filter may be attached.  
Use a polarizing Canon filter (82mm).  
ft  
m
1.5  
2
3 5  
0.5 0.7 1 3  
A filter cannot be used with TS-E17mm f/4L.  
22 11 4 4 11 22  
Distance index  
To ompensate for shifting of the infinity focus  
point that results from changes in temperature.  
The infinity position at normal temperature is the  
point at which the vertical line of the L mark is  
aligned with the distance indicator on the  
distance scale.  
For accurate focusing of subjects at infinity, look  
through the viewfinder’s magnified image* or the  
LCD screen’s magnified image* while rotating the  
focusing ring.  
* For cameras with Live View shooting capability.  
ENG-18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
13. Extension Tubes  
(Sold Separately)  
For TS-E24mm f/3.5L II, you can attach  
extension tube EF12 II for magnified shots. The  
shooting distance and magnification are shown  
below.  
Focusing Distance  
Magnification (×)  
Range (mm)  
Close  
distance distance distance distance  
182 198 0.85 0.51  
Long  
Close  
Long  
EF12 II  
The extension tubes EF12 II and EF25 II ca
be used with TS-E17mm f/4L.  
Although extension tube EF25 II cn be  
attached on TS-E24mm f/3.5L II, s not  
recommended because the lens-toubject  
distance will be very short.  
ENG-19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Specifications  
TS-E17mm f/4L  
TS-E24mm f/3.5L II  
Focal Length/Aperture  
Lens Construction  
Minimum Aperture  
17mm f/4  
12 groups, 18 elements  
24mm f/3.5  
11 groups, 16 elements  
f/22  
f/22  
Diagonal  
Angle of View  
Vertical  
104°  
70° 30’  
93°  
0.25m (0.82f)  
0.14
84°  
53°  
(Normal)  
Horizontal  
74°  
0.21m (0.69ft.)  
0.34×  
Min. Focusing Distance  
Max. Magnification  
Field of View  
168 × 251mm 9.9in)  
±6.
72 × 107mm (2.8 × 4.2inch)  
±8.5°  
Tilt amount  
Shift amount  
±12mm  
Tilt scale display  
Shift scale display  
Rotation mechanism  
TS Rotation mechanism  
1° increments  
1mm increments  
Locks at –90°, 0° and +90°, clicks every 30°  
Locks at right angle and parallel, and clicks at 45°  
ENG-20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Specifications  
TS-E17mm f/4L  
TS-E24mm f/3.5L II  
Filter Diameter  
82mm  
Max. Diameter and Length  
Weight  
Hood  
88.9 × 106.7mm (3.5 × 4.2inch) 88.5 × 106.9mm (3.5 × 4.2inch)  
820g (28.9oz)  
780g (27.5oz)  
EW-88B  
Lens Cap  
Case  
Lens Cap 17  
LP1219  
E-82/E-82 II  
LP1319  
The lens length is measured from the mount surface to te ont end of the lens. Add 26mm to the  
displayed length for TS-E17mm f/4L when include lens ap and dust cap. For TS-E24mm  
f/3.5L II, add 21.5 mm to include the E-82 lens cadust cp, and 24 mm for the E-82 II.  
The size and weight listed are for the lenexpt as indicated.  
The EF1.4 × II/EF2 × II extenders, 250Dsep lenses and the gelatin filter holders III/IV  
cannot be used.  
Aperture settings are specified othe camer
All data listed is measured accordng to anon standards.  
Product specifications and appearanare subject to change without notice.  
ENG-21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1208SZ © CANON INC. 2009  
CT1-8562-002  

Bertazzoni Ventilation Hood KIN 36 PRO X User Manual
Billion Electric Company Network Router 7402NX User Manual
Black Decker Rice Cooker RC426 User Manual
Black Decker Trimmer HH2450 User Manual
Brocade Communications Systems Home Theater Server 12400 User Manual
Brother All in One Printer MFC5100C User Manual
Bryant Air Conditioner 116B User Manual
Carrier Air Conditioner 50RHE006 060 User Manual
Celestron Computer Monitor 80SLT User Manual
CFM Corporation Indoor Fireplace A125 User Manual