PIXMA MP510
SERVICE MANUAL
Revision 0
QY8-13AZ-000
COPYRIGHT©2006 CANON INC. CANON PIXMA MP510 072506 XX 0.00-0
Download from Www.Somanuals.com. All Manuals Search And Download.
I. MANUAL OUTLINE
This manual consists of the following three parts to provide information necessary to service the PIXMA MP510:
Part 1: Maintenance
Information on maintenance and troubleshooting of the PIXMA MP510
Part 2: Technical Reference
New technology and technical information such as FAQ's (Frequently Asked Questions) of the PIXMA MP510
Part 3: Appendix
Block diagrams and pin layouts of the PIXMA MP510
Reference:
This manual does not provide sufficient information for disassembly and reassembly procedures. Refer to the graphics in the separate Parts
Catalog.
Download from Www.Somanuals.com. All Manuals Search And Download.
II. TABLE OF CONTENTS
Part 1: MAINTENANCE
1. MAINTENANCE
1-1. Adjustment, Periodic Maintenance, Periodic Replacement Parts, and Replacement Consumables by Service Engineer
1-2. Customer Maintenance
1-3. Product Life
1-4. Special Tools
1-5. Serial Number Location
2. LIST OF ERROR DISPLAY / INDICATION
2-1. Operator Call Errors
2-2. Service Call Errors
2-3. Other Error Messages
2-4. Warnings
2-5. Troubleshooting by Symptom
3. REPAIR
3-1. Notes on Service Part Replacement (and Disassembling / Reassembling)
3-2. Special Notes on Repair Servicing
(1) Side cover L2 and front cover L removal
(2) Side cover R2 and front cover R removal
(3) Main case removal
(4) Scanner flexible cable attachment
(5) Timing sensor unit cable wiring
(6) Flexible cable between the card board ass'y and the logic board ass'y
(7) Carriage unit flexible cable wiring
(8) Power supply unit cable wiring
(9) Ink tube installation
(10) Platen link assembly
(11) Emblem removal
3-3. Adjustment / Settings
(1) Paper feed motor adjustment
(2) Carriage rail adjustment
(3) Document pressure sheet adjustment
(4) Front feeder paper feed roller cleaning
(5) Grease application
(6) Ink absorber replacement
(7) Ink absorber counter setting
(8) User mode
(9) Service mode
Service mode operation
Destination settings
Ink absorber counter resetting
Ink absorber counter setting
Button and LCD test
3-4. Verification Items
(1) Service test print
(2) EEPROM information print
4. MACHINE TRANSPORTATION
Download from Www.Somanuals.com. All Manuals Search And Download.
Part 2: TECHNICAL REFERENCE
1. NEW TECHNOLOGIES
2. CLEANING MODE AND AMOUNT OF INK PURGED
3. PRINT MODE
3-1. Normal Color Printing via Computer
3-2. Normal Grayscale Printing via Computer
3-3. Borderless Printing via Computer
3-4. Manual Duplex Printing via Computer
3-5. Card / Camera Direct Printing
3-6. Copying
4. FAQ (Problems Specific to the MP510 and Corrective Actions)
Part 3: APPENDIX
1. BLOCK DIAGRAM
2. CONNECTOR LOCATION AND PIN LAYOUT
2-1. Logic Board Ass'y
2-2. Card Slot Board
2-3. Operation Panel Board
2-4. Carriage Board
3. PIXMA MP510 SPECIFICATIONS
Download from Www.Somanuals.com. All Manuals Search And Download.
1. MAINTENANCE
1-1. Adjustment, Periodic Maintenance, Periodic Replacement Parts, and Replacement
Consumables by Service Engineer
(1) Adjustment
Approx.
time
Adjustment
Timing
Purpose
To initialize settings.
Tool
EEPROM
initialization
At logic board replacement
None.
1 min.
1 min.
1 min.
1 min.
Perform in the
service mode.
Destination settings
(EEPROM settings)
At logic board replacement
To set the destination.
None.
Perform in the
service mode.
Ink absorber counter - At logic board replacement
resetting
(EEPROM settings)
To reset the ink absorber counter.
None.
- At ink absorber replacement
Perform in the
service mode.
Ink absorber counter - At logic board replacement
value setting
To set the ink amount data in the ink
absorber to the ink absorber counter.
None.
Perform in the
service mode.
(EEPROM settings)
Paper feed motor
At paper feed motor replacement To adjust the belt tension. (Position the None.
paper feed motor so that the belt is
5 min.
5 min.
position adjustment*1
stretched tight.)
Carriage rail position - At carriage unit replacement
adjustment
To adjust the distance between the print
head and paper (between the carriage
and the platen).
None.
None.
- After carriage rail removal and
re-assembly
- At print head replacement
- At logic board replacement
3 min.
(manual,
auto*2)
Print head alignment
To secure the dot placement accuracy.
- When print quality is not
satisfying
Grease application
- At carriage unit or carriage rail To maintain sliding properties of the
1 min.
FLOIL KG-107A
IF-20
replacement
following items:
- Carriage unit
- LF earth spring
- Eject roller
- At LF earth spring or paper
feed roller replacement
- At platen replacement
Ink system function
check
- At logic board replacement
- At spur base unit replacement
- At carriage unit replacement
To maintain detection functionality for
presence of the ink tanks and each ink
tank position.
1 min.
1 min.
1 min.
None.
Perform in the
service mode.
LCD language
settings
To set the language to be displayed on
the LCD.
None.
At logic board replacement
Perform in the user
mode.
Document pressure
sheet position
adjustment
- At document pressure sheet
replacement
To adjust the pressure sheet to fit in
place to the reference mark in the left
back.
None.
- At document pressure plate
ass'y replacement
*1: The screws securing the paper feed motor may be loosened only at replacement of the paper feed motor unit.
*2: Automatic print head alignment using the print head alignment sheet (via the operation panel only).
(2) Periodic maintenance
No periodic maintenance is necessary.
(3) Periodic replacement parts
There are no parts in this machine that require periodic replacement by a service engineer.
(4) Replacement consumables
There are no consumables that require replacement by a service engineer.
1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
1-2. Customer Maintenance
Approx.
time
Adjustment
Timing
At print head replacement.
Purpose
Tool
Print head
alignment
To ensure accurate dot placement.
- Machine buttons
- Computer (MP driver)
3 min.
(manual,
auto*)
Print head cleaning When print quality is not satisfying.
To improve nozzle conditions.
To improve nozzle conditions.
- Machine buttons
- Computer (MP driver)
1 min.
Print head deep
cleaning
When print quality is not satisfying,
and not improved by print head
cleaning.
- Machine buttons
- Computer (MP driver)
2 min.
Ink tank
replacement
When an ink tank becomes empty.
("No ink error" displayed on the
monitor or on the machine LCD, or
short flashing of an ink tank LED)
To replace the empty ink tank.
None.
1 min.
ASF paper feed
roller cleaning
When paper does not feed properly, or To clean the paper feed rollers.
when the print side of the paper is
smeared
Machine buttons
2 min.
1 min.
Front feeder paper When paper does not feed properly, or To clean the paper feed rollers.
None.
when the back side of the paper is
smeared
Manually clean the rollers
with a cotton swab.
feed roller cleaning
Bottom plate
cleaning
When the back side of the paper is
smeared.
- Machine buttons
- Computer (MP driver)
To clean the platen ribs.
1 min.
1 min.
Scanning area
cleaning
Soft, dry, and clean lint-
free cloth.
When the following are dirty:
- Platen glass
To clean the applicable items.
- Document pressure sheet
* Automatic print head alignment using the print head alignment sheet (via the operation panel only).
1-3. Product Life
(1) Machine
Specified print volume (I) or the years of use (II), whichever comes first.
(I) Print volume: 12,000 pages
Black 1,500 character pattern
Color 7.5% duty per color pattern
A4, photo, borderless printing
4 x 6, photo, borderless printing
Postcard, photo, borderless printing
5,500 pages
3,600 pages
200 pages
2,200 pages
500 pages
(II) Years of use: 5 years of use
(2) Print head
Print volume: 40,000 pages
(3) Ink tank (target value)
CLI-8C
CLI-8M
CLI-8Y
Average yield PGI-5BK
Color document (ISO/IEC
510 pages
880 pages
426 pages
680 pages 690 pages
280 pages 291 pages
FCD24712)*1
Photo (4" x 6")*2
(3,645 pages)
*1: Declared yield value in accordance with ISO/IEC FCD24711. Values obtained by continuous printing.
*2: When printing Canon standard patterns on 4" x 6" Photo Paper Plus Glossy continuously with the default settings of Photo
1-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Paper Plus Glossy using Windows XP printer driver in borderless printing mode and Windows XP Photo Printing Wizard. Declared
yield value determined based on Canon standard method referring to ISO/IEC FCD24712.
Note: Ink yield may vary depending on texts/photos printed, applications software used, print mode and type of paper used.
1-4. Special Tools
Name
Tool No.
Application
Remarks
QY9-0057-000
To be applied to the sliding portions of the
carriage rail and main chassis.
In common with the
S520.
FLOIL KG-107A
ELECTRICITY
GREASE IF-20
CK-8006-000
To be applied to the sliding portions of the
LF earth spring.
1-5. Serial Number Location
On the spur base unit (visible at the front center when the scanning unit is opened).
To the table of contents
To the top
<Part 1: 1. MAINTENANCE>
1-3
Download from Www.Somanuals.com. All Manuals Search And Download.
2. LIST OF ERROR DISPLAY / INDICATION
Errors and warnings are displayed by the following ways:
1) Operator call errors are indicated by the Alarm LED lit in orange, and the error and its solution are displayed on the LCD in text and by
icon.
2) Messages during printing from a computer are displayed on the MP driver Status Monitor.
3) Error codes are printed in the "operator call/service call error record" area in EEPROM information print.
Buttons valid when an operator call error occurs:
1) ON/OFF button: To turn the machine off and on again.
2) OK button: To clear and recover from an error. In some operator call errors, the error will automatically be cleared when the cause of
the error is eliminated, and pressing the OK button may not be necessary.
3) Stop/Reset button: To cancel the job at error occurrence, and to clear the error.
2-1. Operator Call Errors (by Alarm LED Lit in Orange)
Error
Solution
Error code
[1000]
Message on the LCD
Auto sheet feeder.
Confirm that the ASF is selected as the paper
source. Set the paper in the ASF, and press the
OK button.
No paper in the ASF.
There is no paper. Load paper and press [OK].
No paper in the front
feeder.
Front feeder.
Confirm that the front feeder is selected as the
paper source. Set the paper in the front feeder,
and press the OK button.
[1003]
There is no paper. Load paper and press [OK].
The paper is jammed. Clear the paper and press Remove the jammed paper, and press the OK
button.
Paper jam.
[1300]
[1303]
[OK].
Paper jam in the rear
guide.
The following ink may have run out. Replacing Replace the empty ink tank(s), and close the
No ink.
[1600]
cover.
the ink tank is recommended. (U041)
Pressing the OK button will clear the error
without ink tank replacement, however, ink
may run out during printing.
The following ink tank cannot be recognized. Install the applicable ink tank(s) properly, and
Ink tank not installed.
[1660]
[1401]
confirm that the LED's of all the ink tanks light
red.
(Applicable ink tank icon) (U043)
The print head is not
installed, or it is not
properly installed.
Print head is not installed. Install the print
head.
Install the print head properly.
Print head temperature
sensor error
The type of print head is incorrect. Install the Re-set the print head. If the error is not cleared,
[1403]
the print head may be defective. Replace the
correct print head.
print head.
Faulty EEPROM data of
the print head
[1405 / 1682]
[1681]
Multiple ink tanks of the
same color installed.
More than one ink tank of the following color Replace the wrong ink tank(s) with the correct
one(s).
is installed. (U071)
Ink tank in a wrong
position.
Some ink tanks are not installed in place.
(U072)
Install the ink tank(s) in the correct position.
[1680]
Warning: The ink
absorber becomes almost
full.
[1700 / 1701 / Contact the support center or service center for Replace the ink absorber, and reset its counter.
ink absorber replacement. Press [OK] to
1710 / 1711]
[See 3-3. Adjustment / Settings, (6) Service
mode.]
continue printing.
Pressing the OK button will exit the error, and
enable printing without replacing the ink
absorber. However, when the ink absorber
becomes full, no further printing can be
performed unless the applicable ink absorber is
replaced.
The connected digital
camera or digital video
camera does not support
Camera Direct Printing.
Incompatible device detected. Remove the
device.
Remove the cable between the camera and the
machine.
[2001]
[2500]
Failed in automatic print
head alignment.
Failed to scan head alignment sheet. Check
orientation and position, and make sure platen perform automatic print head alignment again
and sheet are clean. <See manual>
Press the OK button to clear the error, and
after confirming the following:
1-4
Download from Www.Somanuals.com. All Manuals Search And Download.
- Fill in all the circles on the print head
alignment sheet.
- Place the sheet in the correct orientation and
position.
The remaining ink amount
unknown.
(Applicable ink tank icon)
An ink tank which has once been empty is
installed. Replace the applicable ink tank with
a new one.
[1683]
The remaining level of the following ink
cannot be correctly detected. Replace the ink
tank. (U130)
Printing with a once-empty ink tank can
damage the printer.
To continue printing without replacing the ink
tank(s), press the OK button for 5 sec. or
longer to disable the function to detect the
remaining ink amount. After the operation, it is
recorded in the printer EEPROM that the
function to detect the remaining ink amount
was disabled.
The following ink tank cannot be recognized. A non-supported ink tank is installed (the ink
Ink tank not recognized. [1684]
tank LED is turned off). Install the supported
ink tanks.
(U140)
(Applicable ink tank icon)
[1410 to
1419]
The following ink tank cannot be recognized. A hardware error occurred in an ink tank (the
Ink tank not recognized.
ink tank LED is turned off). Replace the ink
tank(s).
(U150)
(Applicable ink tank icon)
Scanning unit (printer
cover) open.
Close the scanning unit (printer cover).
[1200]
Cover is open. Close cover.
2-2. Service Call Errors (by Cyclic Blinking in Orange (Alarm LED) and Green (Power LED), or
Both LEDs Lit)
Service call errors are indicated by the number of cycles the Alarm LED and Power LED blink, and the corresponding error code is
displayed on the LCD.
Cycles of blinking
Solution
in orange (Alarm
LED) and green
(Power LED)
Error
code
Error
Conditions
(Replacement of listed parts, which
are likely to be faulty)
2 times
Carriage error [5100] An error occurred in the carriage encoder signal.
Line feed error [6000] An error occurred in the LF encoder signal.
- Carriage unit (QM2-3753)
- Timing slit film (QC1-9542)
- Logic board (QM2-3827)
- Carriage motor (QM2-3872)
3 times
- Timing sensor unit (QM2-3878)
- Timing slit disk film (QC1-9597)
- Feed roller (QL2-1407)
- Logic board (QM2-3827)
- Paper feed motor (QM2-3873)
4 times
5 times
Purge cam
sensor error
[5C00] An error occurred in the purge unit.
- Purge unit (QM2-3754)
- Logic board (QM2-3827)
ASF (cam)
sensor error
This error takes place when feeding paper from the
ASF after an error occurred in the ASF cam sensor.
- Sheet feed unit (QM2-3762)
- ASF_PE sensor board (QM2-3877)
- Logic board (QM2-3827)
[5700]
6 times
7 times
Internal
temperature
error
[5400] The internal temperature is not proper.
- Logic board (QM2-3827)
- Carriage unit (QM2-3753)
Ink absorber
full
[5B00,
5B10,
5B01,
5B11]
- Ink absorber kit (QY5-0178)
The ink absorber is full.
Error codes:
Overseas:
5B00: Main ink absorber
5B10: Borderless-print ink absorber
Japan:
5B01: Main ink absorber
1-5
Download from Www.Somanuals.com. All Manuals Search And Download.
5B11: Borderless-print ink absorber
8 times
Print head
temperature
rise error
[5200] The print head temperature exceeded the specified
value.
- Print head (QY6-0070)
- Logic board (QM2-3827)
9 times
EEPROM
error
[6800] A problem occurred in writing to the EEPROM.
- Logic board (QM2-3827)
10 times
VH monitor
error
[B200] The internal temperature exceeded the specified
value.
- Print head (QY6-0070)
- Carriage unit (QM2-3753)
- Logic board (QM2-3827)
12 times
PG position
error
[5C10] An error occurred in the PG motor during purging
operation.
- Sheet feed unit (QM2-3762)
- Logic board (QM2-3827)
- Purge unit (QM2-3754)
15 times
19 times
USB Host
VBUS
overcurrent
[9000] The USB Host VBUS is overloaded.
[6502] None of the ink tank position is detected.
[6500] The PCI bus error is detected by the ASIC.
- Logic board (QM2-3827)
Ink tank
position sensor
error
- Spur base unit (QM2-3750)
- Logic board (QM2-3827)
20 times
22 times
Other
hardware error
- Logic board (QM2-3827)
Scanner home [5010] The scanner unit cannot detect the home position, or - Scanner unit (QM2-3775)
position error
the scanner unit warming-up is not performed
properly at power-on.
On the LCD, "Scanner is not operating correctly." is
displayed.
Alarm and Power
LEDs lit
ROM error,
RAM error
A flash ROM or RAM checksum error occurred at
hard-power-on.
- Logic board (QM2-3827)
Note: Before replacement of the logic board ass'y, check the ink absorber counter value (by service test print or EEPROM information
print). If the counter value is 7% or more, also replace the ink absorber kit (QY5-0178) when replacing the logic board ass'y, or
register the current ink absorber counter value to the replaced new logic board instead. [See 3-3. Adjustment / Settings, (9)
Service mode, for details.]
2-3. Other Error Messages
Message on the LCD
Cause
Solution
The selected paper cannot be fed from
front feeder. Change the paper source.
The paper type being used is not supported for Change the paper source to the ASF.
paper feeding from the front feeder.
Borderless print is not available for
Borderless print is attempted when the front
Change the paper source to the ASF.
paper from the front feeder. Change the feeder is selected as the paper source.
paper source and press [OK].
Cannot specify the followings together. Settings made conflict each other.
Change one of the settings.
The error message is displayed for a while, then
the LCD automatically returns to the display
before the error occurrence.
Device memory is full. Cannot continue
process. Reduce the number of photos to
print.
Reduce the amount of data to be printed, or
print from a computer.
The memory is not sufficient to do the print job.
Failed to scan. Either document cannot The machine failed in scanning the document
be scanned or is not placed on the platen for Fit-to-page copy, or photos or films were
Press the OK button to clear the error.
glass.
not recognized in pre-scanning.
Press <>.
A temporary error. Press the Color button to
continue the operation.
The Black button was pressed, but it is invalid.
(<>: Color button icon)
Press <>.
A temporary error. Press the Black button to
continue the operation.
The Color button was pressed, but it is invalid.
(<>: Black button icon)
There are no photos in memory card.
Supported image files are not in the memory
card.
A temporary error.
- Confirm that supported image files are in the
memory card.
- Images with double-byte characters used in
the file name (or folder name) may not be
recognized. Change the file (or folder) name
so that it contains only single-byte
alphanumeric characters.
1-6
Download from Www.Somanuals.com. All Manuals Search And Download.
- If images are edited on the computer, print
them from the computer.
The value exceeds the number of copies During selecting images or specifying the
A temporary error. After the error message is
displayed for a while, the last operation before
the error is cancelled, and the total print
you can print.
number of copies, the total print quantity
exceeds the prescribed value of 999.
quantity returns to the value before the error.
Memory card is not set. Insert the card
after checking the direction.
No memory card is inserted in the slot.
Set a memory card.
DPOF information is not saved in the
memory card.
DPOF print was selected in the menu, but no
A temporary error. The error message is
DPOF files are contained in the memory card. displayed for a while, then the LCD
automatically returns to the display before the
error occurrence.
The number of copies to print is not set. Multi-photo print was attempted without
A temporary error. The error message is
displayed for a while, then disappears. Specify
the print quantity.
Input the number of copies.
specifying the print quantity (with the print
quantity left "0" (zero)).
This layout is available only for A4 or
8.5"x11"(215x279).
In Layout print, "Mixed 1, 2, or 3" which is
available only with A4 or LTR size paper is
selected, but the paper size is not set to A4 or
LTR.
A temporary error. The error message is
displayed for a while, then the LCD
automatically returns to the display before the
error occurrence.
Settings cannot be changed when
printing stickers.
With Sticker print selected, the Settings button A temporary error. The error message is
was pressed.
displayed for a while, then the LCD
automatically returns to the display before the
error occurrence.
Change the setting after removing the
card.
With a memory card inserted in the slot, change A temporary error. Remove the memory card,
of the Read/Write attribute was attempted.
then change the Read/Write attribute.
The card is currently write-enabled. Set With the memory card set to the Read/write
A temporary error. Remove the memory card,
change the memory card setting to Read-only,
then perform Card Direct printing.
to read-only mode before performing
mode, Card Direct printing operation was
operation.
attempted from the menu.
The paper size is not correct. Check the Non-supported size of paper for PictBridge
page size you have set. Camera Direct printing is selected.
Cancel printing on the digital camera. Check the
paper size, then print again.
Failed to scan Photo Index Sheet. Check The machine failed in scanning the Photo Index Press the OK button to clear the error.
the orientation, position and marking.
<See manual>
Sheet.
Confirm the following, then try again:
- Fill in all the circles on the Photo Index Sheet.
- Place the sheet in the correct orientation and
position.
2-4. Warnings
Warning
Message on the LCD
Solution
Low ink
The following ink is low. Continue?
(Icon of each ink tank)
Yes No
- Select
, and press the OK button.
Yes
=> Printing starts, and it is indicated on the LCD.
- Select , and press the OK button.
No
=> Printing is cancelled, and the LCD returns to the
display immediately before printing was
attempted.
In Camera Direct Printing, only "Yes" can be selected.
Restrictions on paper
The current paper cannot be set. Change the size and Re-select the supported paper type and size.
type.
USB cable not connected
Connect the USB cable, then turn on the computer.
Connect USB cable and turn on the PC.
Cancellation of image
select information
Reset the selected photo information?
Yes No
When one or more images are selected in Layout print,
and if a user tries to display the menu or sub-menu, the
message is displayed.
- Select
, and press the OK button.
Yes
=> The image selection is cancelled, and the menu
or sub-menu is displayed.
- Select , and press the OK button.
No
=> The LCD returns to the display immediately
before the message was displayed.
1-7
Download from Www.Somanuals.com. All Manuals Search And Download.
2-5. Troubleshooting by Symptom
Symptom
The power does not turn on.
Solution
Faulty operation
- Confirm the connection of
- the power cord, and
The power turns off immediately after
power-on.
- between the logic board and the power supply unit.
- Replace the
- power supply unit, or
- logic board.
A strange noise occurs.
- Remove foreign material.
- Attach a removed part if any.
- Check the operation of the moving parts (such as purge unit,
carriage unit, and paper feeding mechanism)
- Replace a faulty part, if any.
Nothing is displayed on the LCD.
- Confirm the connection between the operation panel, the LCD
unit, and the logic board.
- Replace the
- LCD unit, or
- logic board.
A portion of the LCD is not displayed.
- Perform the button and LCD test in the service mode, and
confirm that the LCD is displayed without any segments
missing.
- Confirm the connection between the operation panel, the
scanning unit, and the logic board.
- Replace the
- LCD unit, or
- logic board.
Paper feed problems (multi-feeding, skewed - Examine the inside to confirm that no parts are damaged, and
feeding, no feeding).
the rollers are clean.
- Remove foreign material.
- Adjust the paper guide properly.
- Re-set the paper.
- Confirm the selected paper source.
- Confirm that the rear cover fits in place properly (for paper
feeding from the front feeder).
- Confirm the connection of each harness and the logic board.
- Replace the
- sheet feeder unit,
- ASF cover unit,
- bottom case unit (for paper feeding from the front feeder), or
- logic board.
Carriage movement problems (contact to
other parts, strange noise).
- Confirm that the carriage timing slit strip film is free from
damage or grease.
- Clean the carriage timing slit strip film (with ethanol and lint-
free paper).
- Remove foreign material.
- Replace the
- carriage timing slit strip film, or
- carriage unit.
Faulty scanning (no scanning, strange
noise).
- Confirm the connection between the scanning unit and the
logic board.
- Replace the
- scanning unit, or
- logic board.
Unsatisfactory print quality No printing, or no color ejected.
- Confirm that the ink tanks are installed properly.
- Perform print head maintenance.
- Replace the
- ink tank,
1-8
Download from Www.Somanuals.com. All Manuals Search And Download.
- print head*1.
- Remove foreign material from the purge unit caps, if any.
- Replace the
- purge unit, or
- logic board.
Printing is faint, or white lines appear on
printouts even after print head cleaning.
- Remove and re-install the print head.
- Confirm that the ink tanks are installed properly.
- Perform print head maintenance.
- Replace the
Line(s) not included in the print data
appears on printouts.
- ink tank,
- print head*1,
- purge unit, or
- logic board.
Paper gets smeared.
- Feed several sheets of paper.
- Perform bottom plate cleaning.
- Clean the paper path with cotton swab or cloth.
- Clean the front feeder paper feed rollers.
A part of a line is missing on printouts.
Color hue is incorrect.
- Replace the
- ink tank, or
- print head*1.
- Confirm that the ink tanks are installed properly.
- Perform print head maintenance.
- Replace the
- ink tank, or
- print head*1.
- Perform print head alignment.
Printing is incorrect.
Replace the logic board.
No ejection of black ink.
- Confirm that the ink tanks are installed properly.
- Perform print head maintenance.
- Replace the
- ink tank, or
- print head*1.
- Remove foreign material from the purge unit caps, if any.
- Replace the purge unit.
Graphic or text is enlarged on printouts.
When enlarged in the carriage movement direction:
- Clean grease or oil off the timing slit strip film.
- Replace the
- timing slit strip film,
- carriage unit, or
- logic board.
When enlarged in the paper feed direction:
- Clean grease or oil off the timing slit disk film.
- Replace the
- timing slit disk film,
- timing sensor unit,
- LF roller, or
- logic board.
No scanning.
- Confirm the connection between the scanning unit and the logic
board.
Faulty scanning
- Replace the
- scanning unit, or
- logic board.
Streaks or smears on the scanned image.
- Clean the platen glass.
- Confirm the connection between the scanning unit and the logic
board.
1-9
Download from Www.Somanuals.com. All Manuals Search And Download.
- Replace the
- scanning unit,
- logic board, or
- document pressure sheet.
*1: Replace the print head only after the print head deep cleaning is performed 2 times, and when the problem persists.
To the table of contents
To the top
<Part 1: 2. LIST OF ERROR DISPLAY / INDICATION>
1-10
Download from Www.Somanuals.com. All Manuals Search And Download.
3. REPAIR
3-1. Notes on Service Part Replacement (and Disassembling / Reassembling)
Notes on replacement*1
Service part
Adjustment / settings
Operation check
Logic board ass'y
QM2-3827
- Before removal of the logic
board ass'y, remove the power
cord, and allow for approx. 1
minute (for discharge of
capacitor's accumulated
charges), to prevent damages to
- EEPROM information print
- Service test print
After replacement:
1. Initialize the EEPROM.
2. Set the destination in the
EEPROM.
- Printing via USB connection
- Copy
3. Set the ink absorber counter
value.
- Direct printing from a digital
camera
the logic board ass'y.
4. Set the language to be
displayed on the LCD.
- Before replacement, check the
ink absorber counter value (by
service test print or EEPROM
information print).
[See 3-3. Adjustment / Settings,
(9) Service mode, for details of 1
to 4]
[See 3-4. Verification Items, (1)
Service test print, or (2)
EEPROM information print, for
details.]
5. Perform the print head
alignment in the user mode.
Absorber kit
QY5-0178
After replacement:
- Service test print
1. Reset the ink absorber counter.
- EEPROM information print
[See 3.3. Adjustment / Settings,
(9) Service mode.]
Carriage unit
QM2-3753
- The screws securing the carriage
rail are allowed to be loosened
only at carriage replacement.
Before removing the screws,
mark the positions of the screws
on the carriage rail so that they
will be returned to their original
positions after the carriage is
replaced.
- Service test print (Confirm ink
system function.)
At replacement:
1. Apply grease to the sliding
portions.
- Printing on thick paper
[See 3-3. Adjustment /
Settings, (5) Grease
application.]
After replacement:
1. Adjust the distance between
the print head and the paper
(between the carriage rail and
the platen).
[See 3.3. Adjustment /
Settings, (2) Carriage rail
adjustment.]
2. Check the ink system function.
[See 3.3. Adjustment /
Settings, (9) Service mode.]
3. Perform the print head
alignment in the user mode.
Paper feed motor
QM2-3873
- The screws securing the paper
feed motor are allowed to be
loosened. (DO NOT loosen any
other red screws.)
At replacement:
1. Adjust the paper feed motor.
[See 3-3. Adjustment / Settings,
(1) Paper feed motor adjustment.]
Spur base unit
QM2-3750
- Service test print
After replacement:
1. Check the ink system function.
[See 3.3. Adjustment / Settings,
(9) Service mode.]
Document pressure plate
ass'y
At replacement:
1. Adjust the document pressure
sheet position.
QM2-3756,
Document pressure sheet
QC1-9514,
[See 3.3. Adjustment / Settings,
(2) Carriage rail adjustment.]
Scanner unit
QM2-3775
Timing slit strip film
QC1-9542
- Upon contact with the film, wipe
the film with ethanol.
- Service test print
After replacement:
1. Perform the print head
alignment in the user mode.
- Confirm no grease is on the film.
(Wipe off any grease thoroughly
with ethanol.)
Timing slit disk film
1-11
Download from Www.Somanuals.com. All Manuals Search And Download.
QC1-9597
Print head
QY6-0070
- Do not bend the film.
- Service test print
After replacement:
1. Perform the print head
alignment in the user mode.
*1: General notes:
- Make sure that the flexible cables and wires in the harness are in the proper position and connected correctly.
See 3-2. Special Notes on Repair Servicing, or Parts Catalog, for details.
- Do not drop the ferrite core, which may cause damage.
- Protect electrical parts from damage due to static electricity.
- Before removing a unit, after removing the power cord, allow the machine to sit for approx. 1 minute (for capacitor discharging
to protect the logic board ass'y from damages).
- Do not touch the timing slit strip film and timing slit disk film. No grease or abrasion is allowed.
- Protect the units from soiled with ink.
- Protect the housing from scratches.
- Exercise caution with the red screws, as follows:
i. The screws of the paper feed motor may be loosened only at replacement of the paper feed motor unit (DO NOT loosen
them in other cases).
ii. The screws securing the carriage rail may be loosened only at replacement of the carriage unit. After carriage unit
replacement, print on thick paper to confirm that the distance between the print head and paper (between the carriage rail
and the platen) is correct, and that the print head does not contact the paper during printing. If the print head contacts the
paper, adjust the carriage rail position, while referring to [3-3. Adjustment / Settings, (2) Carriage rail adjustment.]
To the table of contents
To the top
<Part 1: 3. REPAIR; 3-1. Notes on Service Part Replacement>
1-12
Download from Www.Somanuals.com. All Manuals Search And Download.
3-2. Special Notes on Repair Servicing
(1) Side cover L2 and front cover L removal
i) Remove 1 screw from the front cover L.
ii) While pushing the lock pin, slide the front cover L to the right to remove it.
iii) Release the hook of the right front of the side cover L2, while pulling the cover downward.
iv) Slide the side cover L2 toward the machine front, and remove it.
1-13
Download from Www.Somanuals.com. All Manuals Search And Download.
(2) Side cover R2 and front cover R removal
i) Release the hook of the side cover R2.
ii) Slide the side cover R2 toward the machine front, and remove it.
iii) Remove 1 screw from the front cover R.
1-14
Download from Www.Somanuals.com. All Manuals Search And Download.
iv) Remove 2 hooks (No. 1 in the photo below). While pressing the lock pin (No. 2 in the photo below), slide the front cover R
toward the machine front, and remove it.
(3) Main case removal
i) Remove the front covers L / R, side covers R1 / R2 / L1 / L2, and scanner unit.
ii) Release 2 bosses, and remove the ASF cover unit.
iii) Remove 4 screws and the main case.
1-15
Download from Www.Somanuals.com. All Manuals Search And Download.
(4) Scanner flexible cable attachment
i) On the double-sided adhesive tape in the right back of the top of the main case, attach the flexible cable.
The cores should be located as follows:
- Place the core (No. 2 in the photo below) so that the rib (No. 1 in the photo below) is between the core edges (between the blue
lines in the photo).
- Align another core (indicated by the red arrow in the photo below) to the main case protrusion edges (blue lines in the photo
below).
ii) Attach the FFC sheet, with its right back portion passing under the flexible cable, as shown below (blue circle).
iii) Connect the flexible cable connectors at 3 locations (indicated by the red arrows), while passing the cable through the main case
frame as shown below (blue circle).
1-16
Download from Www.Somanuals.com. All Manuals Search And Download.
(5) Timing sensor unit cable wiring
i) Fit the cables in the flexible cable guide, and attach them to the main chassis with filament tape at 2 locations, as shown below
(blue circles).
ii) Pass the timing sensor unit cables (No. 2 in the photo below) through under the cable between the main board and the ASF_PE
sensor board (No. 1 in the photo below).
1-17
Download from Www.Somanuals.com. All Manuals Search And Download.
(6) Flexible cable between the card board ass'y and the logic board ass'y
i) Attach the core to the cable.
ii) Fix the core with filament tape, as shown in the photo below.
(7) Carriage unit flexible cable wiring
i) Attach the core to a set of carriage unit cables (3 cables).
ii) Fit the cables in the FCC guide so that the core comes to the location indicated by the red arrow in the photo below.
iii) Attach the cables to the main chassis with filament tape, as shown in the photo below (blue circle).
(8) Power supply unit cable wiring
i) Pass the cables through the core 3 times so that they loop around the core.
ii) Fit the cables in the FCC guide.
iii) Using filament tape, attach the cables (together with the timing sensor ass'y cables) to the main chassis , as shown in the photo
below (blue circle).
1-18
Download from Www.Somanuals.com. All Manuals Search And Download.
(9) Ink tube installation
<About Circle 1 in the photo>
Fit the tube between the ribs.
<About Circle 2 in the photo>
Fit the tube between the ribs, and adjust the tube so that the tube end (indicated by the blue circle in the photo) is between the
edges of the right and left ribs (between the red lines in the photo).
1-19
Download from Www.Somanuals.com. All Manuals Search And Download.
(10) Platen link assembly
Assemble the platen link so that the paper thickness lever boss is in the platen link hole, as shown in the photo.
(11) Emblem removal
Push the point indicated by the arrow in the photo to remove from the double-sided adhesive tape.
To the table of contents
To the top
<Part 1: 3. REPAIR; 3-2. Special Notes on Repair Servicing>
1-20
Download from Www.Somanuals.com. All Manuals Search And Download.
3-3. Adjustment / Settings
(1) Paper feed motor adjustment
Perform the following adjustments when the paper feed motor unit is replaced:
1) When attaching the motor, fasten the screws so that the belt is properly stretched (in the direction indicated by the blue arrow in the
figure below).
2) After replacement, be sure to perform the service test print, and confirm that no strange noise or faulty print operation (due to
dislocation of the belt or gear, or out-of-phase motor, etc.) occurs.
Note: The red screws securing the paper feed motor may be loosened only at replacement of the paper feed motor unit. DO NOT
loosen them in other cases.
(2) Carriage rail adjustment
Perform the following adjustments when attaching the carriage rail:
1) Before loosening the screws, mark the following positions on the rail:
- Left side: Mark the boss position.
- Right side: Mark the hole position.
2) In attaching the carriage rail, make sure that the left boss and right hole fit to the marks made in step 1) respectively, then fasten the
screws.
3) Be sure to perform the confirmation test detailed below; confirm that the print quality is proper and the print head is not contacting
the paper.
<Confirmation test>
Using Photo Paper Pro, and with the paper thickness lever set to the left position (normal position), print an image and confirm that the
print quality is proper, and the print head is free from contacting the paper.
If the print quality is not proper, or the print head contacts the paper, adjust the head-to-paper distance in the following procedures:
1-21
Download from Www.Somanuals.com. All Manuals Search And Download.
<How to adjust the head-to-paper distance>
i) Mark the current position of the left boss and the right hole. (See the step 1 of the carriage rail adjustment above.)
ii) Loosen the hexagon-head screws, and adjust the head-to-paper distance.
- To prevent the print head from contacting the paper: Raise the carriage rail from the current position.
- To improve the print quality: Lower the carriage rail from the current position.
(3) Document pressure sheet adjustment
Adjust the document pressure sheet as follows:
1) Peel off the cover sheet from the double-sided adhesive tape of the document pressure sheet, and position one of the corners of the
sheet at the scanning reference point (back left) on the platen glass.
2) Slowly close the document pressure plate ass'y. The document pressure sheet will attach to the document pressure plate ass'y.
3) Open the document cover to confirm the following:
- No extension of the sponge edges over the mold part of the document cover.
- No gap between the platen glass reference edges and the corresponding sponge edges.
(4) Front feeder paper feed roller cleaning
1) Press the ON/OFF button to turn off the machine.
2) Set 5 sheets or more of A4 or letter size plain paper in the front feeder.
3) Push the rear cover tab to the right and pull out the rear cover.
Caution: Be cautious not to touch the collars (indicated by the red circles in the photo below) of the front feeder guide. They can
easily be removed when contacted.
1-22
Download from Www.Somanuals.com. All Manuals Search And Download.
4) While rotating the paper feed roller toward you using your finger, wipe off smears with a cotton swab. If a smear or stain is not
removed easily, moisten the swab and clean the roller.
5) When cleaning is completed, remove the paper from the front feeder, and re-set it.
6) Attach the rear cover.
Caution: Make sure the rear cover fits in place. Improper attachment of the cover will cause paper jams.
(5) Grease application
z Machine unit
Number of
Grease/ oil
amount
Grease/ oil
name
locations to
apply grease/
oil
No
Part name
Where to apply grease/ oil
(mg)
Chassis ass'y
Carriage rail
Carriage rail
Behind the top front of the chassis where the carriage
unit slides
Top surface of the carriage rail where the carriage unit Floil KG107A 475 +/- 25
slides
Front surface of the carriage rail where the carriage unit Floil KG107A 240 +/- 20
slides
Floil KG107A 240 +/- 20
1
1
2
3
(1)
(2)
(3)
1
1
1
4 Carriage rail
(4) Back of the carriage rail where the carriage unit slides
Floil KG107A 250 +/- 50
1-23
Download from Www.Somanuals.com. All Manuals Search And Download.
z Platen
Number of
Number of locations to
Grease/ oil
amount
(mg)
Grease/ oil
name
No Part name
Where to apply grease/ oil
drops*
apply grease/
oil
5 Platen
(5) Eject roller sliding portion
Floil KG107A
4.5 to 9
1/2
3
*1 drop = 9 to 18 mg
z LF roller
Number of
Number of locations to
Grease/ oil
amount
(mg)
Grease/ oil
name
No Part name
6 LF roller
Where to apply grease/ oil
drops*
apply grease/
oil
(6) LF earth spring sliding portion
IF-20
9 to 18
1/2
1
*1 drop = 9 to 18 mg
To the table of contents
To the top
<Part 1: 3. REPAIR, 3-3 (1) to (5)>
1-24
Download from Www.Somanuals.com. All Manuals Search And Download.
(6) Ink absorber replacement
1) At the time of an error indicating that the ink absorber is full, replace either the main or the borderless-print ink absorber according
to the error message.
- When the main ink absorber is full:
Replace the absorber indicated by the blue frame in the photo below (component of QY5-0178).
- When the borderless-print ink absorber is full:
Replace 2 absorbers in the red circle in the photo below and the platen ink absorber (components of QY5-0178).
The main ink absorber and the borderless-print ink absorber have separate counters respectively. After ink absorber replacement,
reset the applicable ink absorber counter according to the replaced ink absorber. For details, see (7) Ink absorber counter setting.
2) Partial replacement of the main ink absorber
For the main ink absorber, the following replacement methods are available:
Print yield after
replacement
Replacement method
Partial replacement
Difficulties
Low
High
Ink absorber volume to be replaced
Approx. a half portion of the entire main
ink absorber
Approx. 4,800 pages
Whole replacement
Approx. 12,000 pages
The entire main ink absorber
After ink absorber replacement, set the ink absorber counter value according to the replacement method. See (7) Ink absorber
counter setting, for details.
<How to perform the partial replacement>
Remove the rear cover (No. 1 in the photo) and the ink absorber cover (No. 2 in the photo) from the rear side of the machine, and
replace a half portion of the main ink absorber (No. 3 in the photo).
(Time required: Approx. 4 min. including the operation check after replacement)
1-25
Download from Www.Somanuals.com. All Manuals Search And Download.
<The portion replaced in the partial replacement>
- Entire main ink absorber: Indicated by the green lines
- The portion to be replaced in partial replacement: Indicated by the blue lines
(7) Ink absorber counter setting
Before replacement of the logic board ass'y, check the ink absorber counter value. After the logic board ass'y is replaced, set the ink
absorber counter value to the replaced logic board ass'y.
In addition, according to the counter value, replace the ink absorber (ink absorber kit). When the ink absorber is replaced, reset the
applicable ink absorber counter (to "0%").
How to check the ink absorber counter value:
See 3-4. Verification Items, (1) Service test print, or (2) EEPROM information print.
How to set the ink absorber counter:
See 3-3. Adjustment / Settings, (9) Service mode, "Ink absorber counter setting procedures."
(8) User mode
Function
Procedures
Remarks
Print head manual cleaning
- Cleaning both Black and Color:
Perform via the machine operation panel.
- Cleaning Black or Color separately, or both Black
and Color:
Perform from the MP driver Maintenance tab.
Print head deep cleaning
Perform via the machine operation panel, or from the
MP driver Maintenance tab.
ASF paper feed roller cleaning Perform via the machine operation panel.
Front feeder paper feed roller
cleaning
Clean the rollers manually.
Nozzle check pattern printing Perform via the machine operation panel, or from the Set a sheet of plain paper (A4 or Letter) in
MP driver Maintenance tab.
the ASF or the front feeder which is
selected on the Paper Feed Switch button.
Manual print head alignment
Perform via the machine operation panel, or from the Set 2 sheets of plain paper (A4 or Letter)
MP driver Maintenance tab.
in the ASF or the front feeder which is
selected on the Paper Feed Switch button.
Automatic print head
alignment
Perform via the machine operation panel.
Print head alignment using the first page
of Print Head Alignment Sheet.
Set a sheet of plain paper (A4 or Letter) in
the ASF or in the front feeder which is
selected by the Paper Feed Switch button.
If the automatic print head alignment is
not effective, perform the manual print
head alignment.
Bottom plate cleaning
Perform via the machine operation panel, or from the Cleaning of the platen ribs when the back
MP driver Maintenance tab.
side of paper gets smeared.
Fold a sheet of plain paper (A4 or Letter)
in half crosswise, then unfold and set it in
the ASF with the folded ridge facing
down.
Download from Www.Somanuals.com. All Manuals Search And Download.
1-26
(9) Service mode
Function
Procedures
Remarks
Service test print
- Model name
See "Service mode operation procedures"
below.
Set a sheet of A4 or letter size paper.
For print sample, see 3-4. Verification Items, (1)
Service test print, <Service test print sample>.
- Destination
- ROM version
- USB serial number
- Ink absorber counter value
(ink amount in the ink
absorber)
- Ink system function check
result
EEPROM information print
- Model name
See "Service mode operation procedures"
below.
Set a sheet of A4 or letter size paper.
- Destination
- ROM version
- Ink absorber counter value
(ink amount in the ink
absorber)
- Print information
- Error information, etc.
EEPROM initialization
See "Service mode operation procedures"
below.
The following items are NOT initialized, and the
shipment arrival flag is not on:
- USB serial number
- Destination settings
- Ink absorber counter value (ink amount in the ink
absorber)
Ink absorber counter reset
Destination settings
See "Service mode operation procedures"
below.
See "Service mode operation procedures"
below.
Button and LCD test
See "Service mode operation procedures"
below.
Ink absorber counter setting
See "Service mode operation procedures"
below.
<Service mode operation procedures>
1) With the machine power turned off, while pressing the Stop/Reset button, press and hold the ON/OFF button. (DO NOT release the
buttons). The Power LED lights in green to indicate that a function is selectable.
2) While holding the ON/OFF button, release the Stop/Reset button. (DO NOT release the ON/OFF button.)
3) While holding the ON/OFF button, press the Stop/Reset button 2 times, and then release both the ON/OFF and Stop/Reset buttons.
(Each time the Stop/Reset button is pressed, the Alarm and Power LEDs light alternately, Alarm in orange and Power in green,
starting with Alarm LED.)
4) When the Power LED lights in green (and "CANON Idle" is displayed on the LCD), press the Stop/Reset button the specified
number of time(s) according to the function listed in the table below, then press the ON/OFF button. (Each time the Stop/Reset
button is pressed, the Alarm and Power LEDs light alternately, Alarm in orange and Power in green, starting with Alarm LED.)
Time(s)
0 times
LED indication
Green (Power)
Function
Remarks
When the print head is not installed, the carriage
returns and locks in the home position capped.
Power off
1 time
Orange (Alarm)
Green (Power)
See 3-4. Verification Items, (1) Service test print.
Service test print
2 times
See 3-4. Verification Items, (2) EEPROM information
print.
EEPROM information print
3 times
4 times
Orange (Alarm)
Green (Power)
EEPROM initialization
Ink absorber counter
resetting
See "Ink absorber counter resetting procedures" below.
5 times
Orange (Alarm)
Destination settings
Press the Stop/Reset button the specified number of
time(s) according to the destination.
1-27
Download from Www.Somanuals.com. All Manuals Search And Download.
See "Destination settings procedures" below.
Cleaning of both Black and Color
6 times
Green (Power)
Print head deep cleaning
7 to 9 times
Orange at odd
numbers (Alarm)
Return to the menu selection
Green at even
numbers (Power)
10 times
11 times
12 times
13 times
Green (Power)
Orange (Alarm)
Green (Power)
Eject roller correction
Return to the menu selection
Button and LCD test
Not used in servicing.
See "Button and LCD test procedures" below.
Orange (Alarm)
Green (Power)
Ink absorber counter setting See "Ink absorber counter setting procedures" below.
Return to the menu selection
14 times or
more
Note: - If the Stop/Reset button is pressed 14 or more times, the Alarm LED (orange) or Power LED (green) lights steadily without
any changes.
<Destination settings procedures>
In the destination settings mode, press the Stop/Reset button the specified number of time(s) according to the destination listed in the
table below, and press the ON/OFF button.
Time(s)
0 times
LED indication
Green (Power)
Orange (Alarm)
Green (Power)
Orange (Alarm)
Green (Power)
Orange (Alarm)
Green (Power)
Orange (Alarm)
Green (Power)
Orange (Alarm)
Destination
No change of the destination
1 time
Japan
2 times
Korea
3 times
US
4 times
Europe
5 times
Australia
6 times
Asia
7 times
China
8 times
Taiwan
9 times or more
Return to the menu selection
Note: Confirm the model name and destination in service test print or EEPROM information print.
<Ink absorber counter resetting procedures>
After replacement of the ink absorber, reset the applicable ink absorber counter.
1) Before replacement of the ink absorber, check the ink absorber counter value in EEPROM information print. See 3-4. Verification
Items, (2) EEPROM information print.
2) In the ink absorber counter resetting mode, press the Stop/Reset button the specified number of time(s) according to the replaced ink
absorber to set its counter to 0%, or 60% (for partial replacement).
Time(s)
0 times
1 time
Replaced ink absorber
Counter value
Reset to 0%
Main ink absorber
Borderless-print ink absorber
Reset to 0%
Reset to 0%
2 times
3 times
Both the main and borderless-print ink absorbers
A half portion of the main ink absorber (partial replacement) Set to 60%
1-28
Download from Www.Somanuals.com. All Manuals Search And Download.
<Ink absorber counter setting procedures>
Set the ink absorber counter data to a replaced new EEPROM after the logic board is replaced in servicing.
1) Before replacement of the logic board ass'y, check the ink absorber counter value in EEPROM information print. See 3-4.
Verification Items, (2) EEPROM information print.
2) In the ink absorber counter setting mode, press the Stop/Reset button the specified number of time(s) according to the ink absorber
whose counter value should be transferred to the replaced new EEPROM.
Time(s)
0 times
Ink absorber
Remarks
Main ink absorber
1 time
Borderless-print ink absorber
Both the main and borderless-print ink absorbers
Not valid
2 times
3 times or more
Press the ON/OFF button to return to the ink absorber counter setting m
3) Press the ON/OFF button to proceed to the next step.
4) The ink absorber counter value can be set in 10% increments by pressing the Stop/Reset button. Press the Stop/Reset button the
appropriate number of time(s) to select the value which is closest to the actual counter value (which was checked in step 1) above.
Time(s)
0 times
1 time
Ink absorber counter value to be set (%)
0%
10%
20%
30%
40%
50%
60%
70%
80%
90%
Not valid.
2 times
3 times
4 times
5 times
6 times
7 times
8 times
9 times
10 times or more
Press the ON/OFF button to return to the ink absorber counter setting mode.
5) Press the ON/OFF button to set the selected value to the EEPROM. Print EEPROM information to confirm that the value is properly
set to the EEPROM.
1-29
Download from Www.Somanuals.com. All Manuals Search And Download.
<Button and LCD test procedures>
Confirm the operation after replacement of the operation panel unit or LCD unit.
1) In the button and LCD test mode, press the Stop/Reset button. The LCD turns blue, waiting for a button to be pressed.
2) Press each button of the operation panel.
The LCD is divided into segments, representing each button. The color of a segment corresponding to the pressed button changes to
red.
When all the buttons are pressed, the entire LCD changes to a full red screen.
The buttons to be pressed are:
- Paper Feed Switch button
- COPY button
- SCAN button
- MEMORY CARD button
- Menu button
- Back button
- Photo Index Sheet button
- Settings button
- OK button
- Black button
- Color button
- Up / down / left / right cursor buttons
3) Open the scanning unit (printer cover) to display the color pattern.
4) Press the ON/OFF button to complete the button and LCD test, and return to the service mode menu selection.
To the table of contents
To the top
<Part 1: 3. REPAIR; 3-3. Adjustment / Settings (6) to (9)>
1-30
Download from Www.Somanuals.com. All Manuals Search And Download.
3-4. Verification Items
(1) Service test print
<EEPROM information contents>
On the service test print (sample below), confirm the EEPROM information as shown below. (The information is printed in the top and
middle areas of the printout.)
- Top area:
MP510: Model name
M = x.xx: ROM version
D = xxx.x: Main ink absorber counter value (%)
USB (xxxxxx): USB serial number
- Below the solid print patterns in each color:
JPN: Destination
- Middle area:
FA = xx xx xx, Temp: Reserved for plant use
AB (C = OK M = ...): Ink system function check result
<Print check items>
On the service test print (sample below), confirm the following items:
- Check 1, top of form accuracy: The lines shall not extend off the paper.
- Check 2, EEPROM information
- Check 3, nozzle check pattern: Ink shall be ejected from all nozzles.
- Check 4, check pattern for uneven printing due to carriage movement or line feeding (standard mode): There shall be no
remarkable unevenness.
- Check 5, check pattern for uneven printing due to carriage movement or line feeding (highest print quality mode): There shall
be no remarkable unevenness.
- Check 6, automatic print head alignment sensor correction: The results shall be OK.
1-31
Download from Www.Somanuals.com. All Manuals Search And Download.
<Service test print sample>
1-32
Download from Www.Somanuals.com. All Manuals Search And Download.
(2) EEPROM information print
<How to read EEPROM information print>
Print sample:
1: MP510 2: JPN 3: V1.01 4: ST=2006/01/28-18:30 5: LPT=2006/05/01-12:09
6: ER(ER0=1300 ER1=5100) 7: P_ON(S=00009) 8: MSD(002)
9: IF(USB1=1) 10: PC(M=002 R=000 T=001 D=009 C=000)
11: D=020.1 Ps=001.0
12: TPAGE（TTL=00162 COPY=00000)
13：CLT(006/01/28-18:38)
14: CH=00002 15: CT(BK=012 M=001 C=001 Y=013)
16: IS(PBK=2 BK=0 Y=2 M=0 C=0)
17: M_REG=0 A_REG=1
18: CDIN(PB=000 OPB=000) 19：BTIN=1
20: PAGE(All=00142 PP=00140 HR+MP=00000 PR+SP+SG=00002 GP=00000 PC=00000 EV=00000)
21: UCPAGE(All=00020)
22: CDPAGE(All=00000)
23: EDGE=00009 24: L=00008 25:BTPAGE=00000 26:EJ=1
27: INK_OFF(BK=0 M=0 C=1 Y=1)
28:Head TempBK=28.0 29:Head TempC=26.5 30:Env Temp=24.0
<Direct>
31: LG=01 Japanese 32: CDI=007 33: CDP=002
34: CDD-PR(L=000 2L=000 PC=000 A4=000)
35: CDD-SP(L=000 2L=000 PC=000 A4=000)
36: CDD-MP(L=000 2L=000 PC=000 A4=000)
37: DCD-PP(L=000 2L=000 PC=000 A4=000)
38: DCD-FPP(L=000 2L=000 PC=000 A4=000)
39: DCD-MPP(L=000 2L=000 PC=000 A4=000)
40:PrnB＝000 41: SC=000 42: Seal=000
<Scanner>
43: SC=00005 44：SCAN_ER(ER0=0000 ER1=0000)
45: SC-dpi(75=00000 150=00000 300=00005 600=00000 1200=00000 2400=00000)
46: SG(GY=00003 CL=00002)
<Copy>
47: MCASF(PP=00000 SP+PR+GP=00000 OTH=00000)
48: CCASF(PP=00000 HR+MP=00000 PR+SP+SG=00000 GP=00000 PC=00000)
1-33
Download from Www.Somanuals.com. All Manuals Search And Download.
Printed items:
1. Model name 2. Destination 3. ROM version 4. Installation date & time 5. Last printing date & time
6. Operator call/service call error record 7. Power-on count (soft) 8. Longest period where printing stops (days)
9. Connected I/F (USB2) 10. Purging count (manual/deep cleaning/timer/dot count/ink tank and print head replacement)
11. Main ink absorber counter value (%), borderless-print ink absorber counter value (%)
12. Total print pages (total, copy pages)
13. Cleaning date & time (BK/CL)
14. Print head replacement count 15. Ink tank replacement count (BK/M/C/Y)
16. Ink status (BK/Y/M/C) => 0 (High) / 1 (Middle) / 2 (Low) / 3 (Empty)
17. Manual print head alignment by user, automatic print head alignment by user
18. Camera Direct Print-supported device connection record (PB = Canon PictBridge-supported camera, OPB = Other PictBridge-
supported camera)
19. Bluetooth device connection record
20. ASF feed pages (total, plain paper, High Resolution Paper & Matte Photo Paper, Photo Paper Pro & Photo Paper Plus Glossy &
Photo Paper Plus Semi-gloss, Glossy Photo Paper, postcard, envelope)
21. Front feeder feed pages (total)
22. Camera Direct print pages (total)
23. Borderless print pages 24. L size and 4x6 print pages 25. Print pages via Bluetooth connection 26. Paper eject roller correction
value (not used in servicing)
27. Disabling of the remaining ink amount detection function (BK/M/C/Y)
28. Print head temperature (BK) 29. Print head temperature (CL) 30. Internal temperature
<Direct>
31. Language 32. Memory card use count 33. Total Card Direct print pages
34. Card Direct print pages: Photo Paper Pro (4 x 6, 5 x 7, Japanese post card, A4)
35. Card Direct print pages: Photo Paper Plus Glossy (4 x 6, 5 x 7, Japanese post card, A4)
36. Card Direct print pages: Matte Photo Paper (4 x 6, 5 x 7, Japanese post card, A4)
37. Camera Direct print pages: Photo Paper (4 x 6, 5 x 7, Japanese post card, A4)
38. Camera Direct print pages: Fast Photo Paper (4 x 6, 5 x 7, Japanese post card, A4)
39. Camera Direct print pages: Matte Photo Paper (4 x 6, 5 x 7, Japanese post card, A4)
40. Print Beam print pages 41. Business Card and Credit Card size paper print pages 42. Sticker sheet print pages
<Scanner>
43. Total scan count
44. The last 2 errors (including user errors and copy scan errors. Even if the same errors occur, they are recorded individually.)
45. Scan count by scanning resolution (75, 150, 300, 600, 1200, 2400 dpi)
46. Scan count by scanning gradation (grayscale, color)
<Copy>
47. Monochrome copy pages fed via the ASF (plain paper, Photo Paper Plus Glossy & Photo Paper Pro & Glossy Photo Paper, other)
48. Color copy pages fed via the ASF (plain paper, High Resolution Paper & Matte Photo Paper, Photo Paper Pro & Photo Paper Plus
Glossy & Photo Paper Plus Semi-gloss, Glossy Photo Paper, postcard)
To the table of contents
To the top
<Part 1: 3. REPAIR; 3-4. Verification Items>
1-34
Download from Www.Somanuals.com. All Manuals Search And Download.
4. MACHINE TRANSPORTATION
This section describes the procedures for transporting the machine for returning after repair, etc.
1) In the service mode, press the ON/OFF button to finish the mode, and confirm that the paper lifting plate of the sheet feed unit is
raised.
2) Keep the print head and ink tanks installed in the carriage.
See Caution 1 below.
3) Turn off the machine to securely lock the carriage in the home position. (When the machine is turned off, the carriage is
automatically locked in place.)
See Caution 2 below.
4) Tape the following points:
(1) Paper support: Right and left sides
(2) Paper output tray: Right and left sides
(3) Paper thickness lever: Set the lever to the left (for the regular head-to-paper distance), and fix it with tape.
Caution:
(1) If the print head is removed from the machine and left alone by itself, ink (the pigment-based black ink in particular) is likely to
dry. For this reason, keep the print head installed in the machine even during transportation.
(2) Securely lock the carriage in the home position, to prevent the carriage from moving and applying stress to the carriage flexible
cable, or causing ink leakage, during transportation.
Memo:
If the print head must be removed from the machine and transported alone, attach the protective cap (used when the packing was
opened) to the print head (to protect the print head face from damage due to shocks).
To the table of contents
To the top
<Part 1: 4. MACHINE TRANSPORTATION>
1-35
Download from Www.Somanuals.com. All Manuals Search And Download.
Part 2
TECHNICAL REFERENCE
Download from Www.Somanuals.com. All Manuals Search And Download.
1. NEW TECHNOLOGIES
(1) Paper thickness lever (at the bottom front of the machine)
The head-to-paper distance can be adjusted using the paper thickness lever.
Smearing on printouts due to the print head contacting the paper, etc. may be solved by setting the paper thickness lever to the right (for
thick paper, envelope, and T-shirt transfer), regardless of the paper type.
(2) Remaining ink amount detection function
The machine has a function to detect the remaining ink amount.
Detection method: Optical method and dot count
Display method: Displayed on the Status Monitor
Level 1: Approx. 70% of ink remaining, status display only
Level 2: Approx. 40% of ink remaining, status display only
Level 3: Indication of "!" mark, "Ink low" warning
Level 4: Indication of "X" mark, "No ink" error (ink may have run out)
By pressing the Stop/Reset button, printing can be continued without replacing the applicable ink tank(s), though printouts
may be faint.
Level 5: Indication of "X" mark, "No ink" error (ink has run out)
By pressing the Stop/Reset button for 5 seconds or longer, the function to detect the remaining ink amount is disabled, and
printing can be continued without replacing the applicable ink tank(s).
After this operation, it is recorded in the EEPROM that the function to detect the remaining ink amount was disabled.
Printing with an empty ink tank will cause a problem. Promptly replace the applicable ink tank(s).
(3) Two-way paper feeding
Paper can be fed either from the auto sheet feeder or from the front feeder.
The auto sheet feeder is selected at default.
- Auto sheet feeder: All the supported types and sizes of paper can be fed.
- Front feeder: Only A4, B5, and Letter size plain paper can be fed.
(4) Print head alignment
Since it is NOT necessary to perform print head alignment at setup or installation of the machine, the function is only briefly introduced
at the installation.
If print quality is not satisfying (such as dot mis-alignment on a line), perform print head alignment.
Two types of print head alignment are available.
- Automatic print head alignment:
Perform via the machine operation panel, using the Print Head Alignment Sheet.
Print the first page of the Print Head Alignment Sheet in the manual print head alignment mode first, then fill in the applicable
circles on the sheet, and scan the sheet.
In automatic print head alignment, only the first page of the Print Head Alignment Sheet is used.
If automatic print head alignment is not effective, perform manual print head alignment.
Note: If all the necessary circles are not filled in, or the alignment sheet is not placed properly on the platen glass for scanning, the
automatic print head alignment error will occur. In such a case, start from printing a blank form of the Print Head Alignment
Sheet again.
- Manual print head alignment:
Perform via the machine operation panel or from the MP driver.
To the table of contents
To the top
<Part 2: 1. NEW TECHNOLOGIES>
2-1
Download from Www.Somanuals.com. All Manuals Search And Download.
2. CLEANING MODE AND AMOUNT OF INK PURGED
To prevent printing problems due to bubbles, dust, or ink clogging, print head cleaning is performed before the start of printing (when the
cleaning flag is on), except in the following cases:
- Cleaning on arrival: Performed when the scanning unit (printer cover) is closed.
- Manual cleaning / deep cleaning: Performed manually.
<Cleaning mode list>
Black: Pigment-based black
Color: Dye-based cyan, magenta, yellow
Est. required time
Amount of ink used (g)
(sec.)
(in the normal
temperature/humidity
Condition
Details
(not including the
time of opening the
caps)
environment)
0.50 (Black)
1.12 (Color)
On arrival of the
machine
First to third cleaning after shipped from the
plant.
97
47 for the 3rd
cleaning
Black only for the 3rd
cleaning.
(All in sequence)
0.20 (Black)
46 (Black)
46 (Black)
When the specified number of dots are printed
since the previous Black cleaning.
Dot count cleaning
(Black)
Timer cleaning - 0*1
(Black only)
If 24 to 60 hours have elapsed since the previous 0.20 (Black)
Black cleaning till the start of the next printing.
Timer cleaning - 1
(Black only)
If 60 to 240 hours have elapsed since the previous
Black cleaning till the start of the next printing.
Timer cleaning - 2*2
0.20 (Black)
46 (Black)
If 240 to 336 hours have elapsed since the
36 (Color)
(All in
sequence/Black/Color)
0.46 (Color)
previous Black/Color cleaning till the start of the
next printing.
37 (All in sequence)
Timer cleaning - 3
(All in sequence)
0.54 (Black)
0.79 (Color)
If 336 to 1,080 hours have elapsed since the
previous Black/Color cleaning till the start of the
next printing.
83
85
88
88
97
Timer cleaning - 4
(All in sequence)
0.77 (Black)
0.79 (Color)
If 1,080 to 2,160 hours have elapsed since the
previous Black/Color cleaning till the start of the
next printing.
Timer cleaning - 5
(All in sequence)
1.39 (Black)
0.79 (Color)
If 2,160 to 4,320 hours have elapsed since the
previous Black/Color cleaning till the start of the
next printing.
Timer cleaning - 6
(All in sequence)
If 4,320 or longer hours have elapsed since the
previous Black/Color cleaning till the start of the
next printing.
At print head
replacement
0.50 (Black)
1.12 (Color)
When the print head is removed and installed.
(All in sequence)
81 (All in sequence)
47 (Black)
0.33 (Black)
0.79 (Color)
At ink tank
replacement*3
When an ink tank is replaced (without the print
head removal or re-installation)
51 (Color)
(Black/Color/All in
sequence)
0.20 (Black)
0.46 (Color)
37 (All at the same
time)
- Via the operation panel (All at the same time
only)
Manual cleaning
(Black/Color/All at the
same time)
46 (Black)
36 (Color)
- Via the MP driver (Selectable from Black,
Color, or All at the same time)
89 (All at the same
time)
1.63 (Black)
0.79 (Color)
Via the MP driver (Selectable from Black, Color,
or All at the same time)
Deep cleaning
(Black/Color/All at the
54 (Black)
2-2
Download from Www.Somanuals.com. All Manuals Search And Download.
52 (Color)
same time)
If the print head has not
been capped before
power-on
0.33 (Black)
0.79 (Color)
81 (All in sequence)
(All in sequence)
*1: When 24 to 60 hours have elapsed since the previous Black cleaning, timer cleaning - 0 is performed. However, this
cleaning will be conducted up to 5 times from the machine installation, and no further timer cleaning - 0 will be performed.
*2: The period of time since the previous cleaning is counted by Black and Color separately. For this reason, the cleaning mode
may differ according to Black or Color.
*3: When only the black ink tank is replaced, Black cleaning is performed. One of the color ink tanks is replaced, Color
cleaning is performed. Both the black and color ink tanks are replaced, All-at-the-same-time cleaning is performed.
To the table of contents
To the top
<Part 2: 2. CLEANING MODE AND AMOUNT OF INK PURGED>
2-3
Download from Www.Somanuals.com. All Manuals Search And Download.
3. PRINT MODE
Default setting
Selectable in the printer driver Main tab
Selectable after clicking Custom in the Main tab
Ink used PigBk: PGI-5BK
C: CLI-8C
M: CLI-8M
Y: CLI-8Y
CLI-8C (small
droplet)
c:
CLI-8M (small
droplet)
m:
Print control
Bi: Bi-directional
Uni: Uni-directional
3-1. Normal Color Printing via Computer
MP driver Custom setting
3
Paper type
5
4
2
1
(Canon specialty paper)
Item
Fast
Fine
Plain paper
Print quality
Resolution HxV (dpi) 300x300
Print control
Ink used
Custom
Fast
600x600
1 pass, Bi
Standard
600x600
1 pass, Bi
High
600x600
4 passes, Bi
1 pass, Bi
PigBk/C/M/Y PigBk/C/M/Y PigBk/C/M/Y PigBk/C/M/Y/c/m
Photo Paper Pro
(PR-101)
Print quality
Resolution HxV (dpi)
Print control
Standard
600x600
4 passes, Bi
C/M/Y/c/m
High
600x600
6 passes, Bi 16 passes, Bi
C/M/Y/c/m
Custom
600x600
Ink used
C/M/Y/c/m
Photo Paper Plus Glossy
Photo Paper Plus Semi-gloss
(PP-101/SG-201)
Print quality
Resolution HxV (dpi)
Print control
Ink used
Standard
600x600
4 passes, Bi
C/M/Y/c/m
High
600x600
6 passes, Bi
C/M/Y/c/m
Photo Paper Plus Double Sided Print quality
Standard
600x600
High
600x600
(PP-101D)
Resolution HxV (dpi)
Print control
4 passes, Bi
6 passes, Bi
Ink used
C/M/Y/c/m
C/M/Y/c/m
Matte Photo Paper
(MP-101)
Print quality
Resolution HxV (dpi)
Print control
Standard
600x600
4 passes, Bi
C/M/Y/c/m
High
600x600
6 passes, Bi
C/M/Y/c/m
Ink used
Glossy Photo Paper
(GP-401/501)
Print quality
Resolution HxV (dpi)
Print control
Standard
600x600
4 passes, Bi
C/M/Y/c/m
High
600x600
6 passes, Bi
C/M/Y/c/m
Ink used
High Resolution Paper
(HR-101)
Print quality
Resolution HxV (dpi)
Print control
Standard
600x600
4 passes, Bi
C/M/Y/c/m
High
600x600
6 passes, Bi
C/M/Y/c/m
Ink used
Envelope
Print quality
Resolution HxV (dpi)
Standard
600x600
High
600x600
Print control
3 passes, Bi
4 passes, Bi
Ink used
PigBk/C/M/Y PigBk/C/M/Y/c/m
T-Shirt transfer
(TR-301)
Print quality
Resolution HxV (dpi)
Print control
Ink used
Standard
600x600
6 passes, Bi
C/M/Y
Other Photo Paper
Print quality
Resolution HxV (dpi)
Print control
Standard
600x600
8 passes, Bi
Ink used
C/M/Y/c/m
2-4
Download from Www.Somanuals.com. All Manuals Search And Download.
3-2. Normal Grayscale Printing via Computer
MP driver Custom setting
3
Paper type
5
1
Fine
(Canon specialty
Fast
4
2
paper)
Item
Plain paper
Print quality
Resolution HxV (dpi)
Print control
Custom
300x300
1 pass, Bi
PigBk
Fast
600x600
1 pass, Bi
PigBk
Standard
600x600
1 pass, Bi
PigBk
High
600x600
4 passes, Bi
PigBk
Ink used
Envelope
Print quality
Resolution HxV (dpi)
Standard
600x600
High
600x600
Print control
Ink used
2 passes, Uni 4 passes, Uni
PigBk PigBk
3-3. Borderless Printing via Computer
MP driver Custom setting
3
Paper type
(Canon specialty
5
Fast
1
Fine
4
2
paper)
Item
Plain paper
Print quality
Resolution HxV (dpi)
Print control
Standard
600x600
2 passes, Bi
C/M/Y
Ink used
Photo Paper Pro
(PR-101)
Print quality
Resolution HxV (dpi)
Print control
Standard
600x600
4 passes, Bi
C/M/Y/c/m
High
600x600
6 passes, Bi
C/M/Y/c/m
Custom
600x600
16 passes, Bi
C/M/Y/c/m
Ink used
Photo Paper Plus
Glossy
Print quality
Resolution HxV (dpi)
Standard
600x600
High
600x600
Photo Paper Plus
Semi-gloss
Print control
Ink used
4 passes, Bi
C/M/Y/c/m
6 passes, Bi
C/M/Y/c/m
(PP-101/SG-201)
Photo Paper Plus
Double Sided
(PP-101D)
Print quality
Resolution HxV (dpi)
Print control
Ink used
Standard
600x600
4 passes, Bi
C/M/Y/c/m
High
600x600
6 passes, Bi
C/M/Y/c/m
Matte Photo Paper
(MP-101)
Print quality
Resolution HxV (dpi)
Print control
Standard
600x600
4 passes, Bi
High
600x600
6 passes, Bi
Ink used
C/M/Y/c/m
C/M/Y/c/m
Glossy Photo Paper Print quality
Standard
600x600
High
600x600
(GP-401/501)
Resolution HxV (dpi)
Print control
Ink used
4 passes, Bi
C/M/Y/c/m
6 passes, Bi
C/M/Y/c/m
Other Photo Paper
Print quality
Resolution HxV (dpi)
Print control
Standard
600x600
8 passes, Bi
C/M/Y/c/m
Ink used
3-4. Manual Duplex Printing via Computer
MP driver Custom setting
Paper type
(Canon specialty paper)
5
Fast
1
Fine
4
3
2
Item
Plain paper
Print quality
Resolution HxV (dpi)
Print control
Custom
300x300
1 pass, Bi
Fast
600x600
1 pass, Bi
Standard
600x600
1 pass, Bi
High
600x600
1 pass, Bi
Ink used
PigBk/C/M/Y PigBk/C/M/Y PigBk/C/M/Y PigBk/C/M/Y/c/m
Plain paper,
borderless printing
Print quality
Resolution HxV (dpi)
Print control
Standard
600x600
2 passes, Bi
C/M/Y
Ink used
Photo Paper Plus Glossy Print quality
Standard
600x600
4 passes, Bi
C/M/Y/c/m/k
High
600x600
6 passes, Bi
C/M/Y/c/m/k
Double Sided
(PP-101D)
Resolution HxV (dpi)
Print control
Ink used
2-5
Download from Www.Somanuals.com. All Manuals Search And Download.
3-5. Card / Camera Direct Printing
Paper type
(Canon specialty paper)
Fast
Standard
High
Item
Plain paper
Print quality
Resolution HxV (dpi)
Print control
Standard
600x600
1 pass, Bi
PigBk/C/M/Y
High
600x600
4 passes, Bi
PigBk/C/M/Y/c/m
Ink used
Glossy Photo Paper
(GP-401/501)
Print quality
Resolution HxV (dpi)
Print control
Standard
600x600
4 passes, Bi
C/M/Y/c/m
High
600x600
6 passes, Bi
C/M/Y/c/m
Ink used
Photo Paper Pro
(PR-101)
Print quality
Resolution HxV (dpi)
Standard
600x600
High
600x600
Print control
Ink used
4 passes, Bi
C/M/Y/c/m
6 passes, Bi
C/M/Y/c/m
Matte Photo Paper
(MP-101)
Print quality
Resolution HxV (dpi)
Print control
Standard
600x600
4 passes, Bi
High
600x600
6 passes, Bi
Ink used
C/M/Y/c/m
C/M/Y/c/m
Photo Paper Plus Glossy
Photo Paper Plus Semi-
gloss
Print quality
Resolution HxV (dpi)
Print control
Standard
600x600
4 passes, Bi
C/M/Y/c/m
High
600x600
6 passes, Bi
C/M/Y/c/m
(PP-101/SG-201)
Ink used
3-6. Copying
Paper type
(Canon specialty paper)
Fast
Standard
High
Item
Plain paper
Resolution HxV (dpi)
Print control
Ink used
300x300
1 pass, Bi
PigBk
600x600
1 pass, Bi
PigBk
600x600
4 passes, Bi
PigBk
Single sided, B&W
(Borderless printing not
supported)
Plain paper
Resolution HxV (dpi)
Print control
Ink used
300x300
1 pass, Bi
PigBk/C/M/Y
600x600
1 pass, Bi
PigBk/C/M/Y
600x600
4 passes, Bi
PigBk/C/M/Y/c/m
Single sided, Color
(Borderless printing not
supported)
Glossy Photo Paper
(GP-401/501)
Resolution HxV (dpi)
Print control
Ink used
600x600
4 passes, Bi
C/M/Y/c/m
600x600
6 passes, Bi
C/M/Y/c/m
Single sided, B&W/Color
Photo Paper Pro
(PR-101)
Resolution HxV (dpi)
Print control
Ink used
600x600
4 passes, Bi
C/M/Y/c/m
600x600
6 passes, Bi
C/M/Y/c/m
Single sided, B&W/Color
Matte Photo Paper
(MP-101)
Resolution HxV (dpi)
Print control
Ink used
600x600
4 passes, Bi
C/M/Y/c/m
600x600
6 passes, Bi
C/M/Y/c/m
Single sided, B&W/Color
Photo Paper Plus Glossy
Photo Paper Plus Semi-
gloss
Resolution HxV (dpi)
Print control
Ink used
600x600
4 passes, Bi
C/M/Y/c/m
600x600
6 passes, Bi
C/M/Y/c/m
(PP-101/SG-101)
Single sided, B&W/Color
To the table of contents
To the top
<Part 2: 3. PRINT MODE>
2-6
Download from Www.Somanuals.com. All Manuals Search And Download.
4. FAQ (Problems Specific to the MP510 and Corrective Actions)
Possible call or
complaint
No.
*
Function
Phenomenon
Condition
Cause
Corrective action
Ink tank installed
A Installation in a wrong
position
The ink tank is installed in Open the scanning unit
a wrong position.
- Ink tank installation
(printer cover), and install error.
the ink tank(s) properly.
1
Print head
Insufficient allowance of Remove and re-install the - Print head
2
3
B
B
Installation installation error
the print head positioning print head.
part.
installation error.
No paper feeding - Paper feeding
from the ASF
The paper feed roller slips 1. Perform paper feed
- Paper out error
- Paper cannot be fed
- Cannot print
on the paper at paper
feeding.
roller cleaning.
- Postcard
2. Clean the paper feed
roller with pre-
moistened wipe or
moistened cloth.
Paper feed
3. Correct paper curl. If
the problem persists,
adjust the printer
guide to leave approx.
0.5 mm between the
guide and the paper
edge.
Multi-feeding
- In the high
temperature and and high humidity
In the high temperature
1. Fan the paper before
setting them.
- Multiple sheets of
paper are fed
high humidity
environment
environment, the
simultaneously.
2. In case of PR-101, set
the paper sheet by
sheet.
frictional force between
the front and back sides of
paper becomes high, and
sheets stick to each other,
contributing to multi-
feeding.
- Blank paper is
ejected.
4
C
Paper feed
3. Recommend use of the
ASF for printing on
both sides of paper
(manual duplex
printing).
Envelope not
feeding
- Envelope
The paper feed roller slips 1. Perform paper feed
- Paper out error
- Paper cannot be fed
- Cannot print
on the paper at paper
feeding.
roller cleaning via the
operation panel.
Note:
2. Clean the paper feed
roller with pre-
Depending on the paper
lots.
moistened wipe or
moistened cloth.
5
B
Paper feed
3. Reduce the number of
envelopes set in the
ASF.
4. Flatten the envelope
(with a pen).
5. If the paper support is
extended, retract it.
Paper jam
1. As the LF roller slips 1. Remove the jammed
- Paper jam error
- Paper cannot be fed
- Cannot print
on the paper, the paper
is not fed, causing the
jam error at paper
ejecting.
paper from the paper
pick-up side.
2. Confirm that the
printer guide is
2. The printer guide is not
properly set.
properly adjusted.
3. Confirm that the paper
source is properly
selected.
3. The paper source
where the paper is set
is not selected.
4. For Legal size paper,
close the tab of the
6
C
Paper feed
4. When the tab of the
paper support is
output paper support.
raised, the Legal size
paper hits it before the
paper is completely
ejected.
5. In case of a paper jam
in the front feeder,
confirm that the rear
cover securely fits in
place after the paper
previously jammed in
the front feeder was
removed.
5. If the rear cover is not
properly attached, the
edge of paper contacts
the rear cover during
2-7
Download from Www.Somanuals.com. All Manuals Search And Download.
paper feeding, resulting in
a paper jam.
Smearing on
printed side
When paper is curled, the 1. Correct the paper curl. - Smear on the
edge of paper rises,
causing the print head to
rub against the printed
surface of paper, resulting
in smearing.
printed side of
paper
2. Recommend printing
in the print quality
assurance area.
Print
results
7
B
- Cannot print
properly
- Paper edge crease
Smearing on the
back side of
paper, or on the
address side of
postcards
When borderless printing 1. Perform Bottom plate <Photo Paper Plus
is performed
cleaning via the
operation panel.
Double Sided>
continuously, ink mist
attaches to the platen ribs,
and is transferred to the
backside of the following
paper.
Smears on the
already printed side
when printing the
other side
Change the paper in
each Bottom plate
cleaning.
The cleaning can end <When printing the
when paper does not address side of
Print
results
8
B
get any smearing.
postcards>
2. Clean the platen ribs
with cotton swabs,
etc.
Smears on the
address side
<When printing the
message side of
postcards>
Smears on the
backside
Horizontal lines
or uneven print
density at the
trailing edge of
paper
When the paper end
comes off the pinch roller,
printing is performed
without the paper being
held, preventing the ink
drops from being ejected
in the correct positions,
resulting in unevenness.
1. Recommend printing - Cannot print to the
in the print quality
bottom edge of
assurance area.
paper
2. Change the print
quality from Standard
to High mode.
- Lines or uneven
print density appear
in the trailing edge
of paper
Print
results
9
C
3. Try other paper (PP-
101).
- Cannot print
properly
Error in print
head alignment
- Automatic print 1. Some circles on the
Press the OK button to
clear the error.
- Error in print head
alignment
head alignment
using the Print
Head Alignment
Sheet
Print Head Alignment
Sheet were not filled
in.
Perform print head
2. The sheet was not
placed properly on the
platen glass.
alignment again, from
printing of a blank form
of the Print Head
10
C Installation
Alignment Sheet. When
starting over print head
alignment, always start
from printing out the
blank form (scanning of
the filled-in sheet alone
cannot be performed).
Removal of the - At removal of the Since the collars are
Attach the removed part. - A part is removed
front feeder guide rear cover
collar
loosely attached, they are
easy to be removed when
touched.
Advise a user not to
contact the collars when
the rear cover is opened.
11
B
Other
* Occurrence level:
A: The symptom is likely to occur frequently. (Caution required)
B: The symptom may occur under certain conditions, but likeliness is assumed very low in practical usage.
C: The symptom is unlikely to be recognized by the user, and no practical issues are assumed.
To the table of contents
<Part 2: 4. FAQ>
To the top
2-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Part 3
APPENDIX
Download from Www.Somanuals.com. All Manuals Search And Download.
1. BLOCK DIAGRAM
1-1. PIXMA MP510
Link to a PDF file for printing
To the table of contents
To the top
<Part 3: 1. BLOCK DIAGRAM>
3-1
Download from Www.Somanuals.com. All Manuals Search And Download.
2. CONNECTOR LOCATION AND PIN LAYOUT
2-1. Logic Board Ass'y
J301 (Print Head 1/3 [Carriage Unit])
Input /
Output
No.
Signal name
Function
1 to 4
5 to 9
VH_GND
VH
Head drive ground
-
OUT
-
Head driver power supply +24V
Head drive ground
10 to 14 VH_GND
J302 (Print Head 2/3 [Carriage Unit])
Input /
Output
No.
Signal name
Function
1 to 2
3 to 5
6
HVDD
Head logic power supply +3.3V
Head logic power supply +24V
System ground
OUT
OUT
-
VH
SGND
7
B_DIA
Diode sensor anode B
System ground
IN
-
8
SGND
9
A_DIA
Diode sensor anode A
System ground
IN
-
10
11
12
13
14
SGND
ENC_OUT_A
SGND
Encoder output signal A
System ground
IN
-
ENC_OUT_B
ENC_PWR
Encoder output signal B
Encoder drive power supply +3.3V
IN
OUT
3-2
Download from Www.Somanuals.com. All Manuals Search And Download.
J303 (Print Head 3/3 [Carriage Unit])
Input /
Output
No.
Signal name
Function
1
AB_PWR
AB_DATA
AB_PWR
AB_CLK
THERMO
H_ENB2
HD9_Y2
HD13_C2
HD11_M2
HD12_SC2
HD10_SM2
ROM_DIO
SGND
Ink tank sensor chip power supply
Ink tank sensor data power supply
Ink tank sensor chip power supply
Ink tank sensor data transfer clock signal
Carriage temperature sensor signal
Head heat enable signal 2
Head data (Y2)
OUT
BUS
OUT
BUS
IN
2
3
4
5
6
OUT
OUT
OUT
OUT
OUT
OUT
IN/OUT
-
7
8
Head data (C2)
9
Head data (M2)
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
Head data (SC2)
Head data (SM2)
Head EEPROM input - output data
System ground
Head data transfer clock signal
System ground
H_CLK
OUT
-
SGND
ROM_SK
HLAT
Head EEPROM serial clock signal
Head data latch signal
Head data (Y1)
OUT
OUT
OUT
OUT
OUT
OUT
OUT
OUT
OUT
OUT
OUT
OUT
OUT
HD8_Y1
ROM_CS
HENB1
Head EEPROM chip select signal
Head heat enable signal1
Head heat enable signal 3
Head data (C1)
HENB3
HD2_C1
HENB0
Head heat enable signal0
Head data (BK1)
HD0_K1
HD4_M1
HD1_K2
HD5_SM1
HD3_SC1
Head data (M1)
Head data (BK2)
Head data (SM1)
Head data (SC1)
J501 (LF Encoder)
Input /
Output
No.
Signal name
Function
1
2
3
4
GND
Ground
-
ENCA
VSEN
ENCB
LF encoder phase A
Sensor power supply +3.3V
LF encoder phase B
IN
OUT
IN
3-3
Download from Www.Somanuals.com. All Manuals Search And Download.
J502 (Ink Sensor / Ink Tank Sensor)
Input /
Output
No.
Signal name
Function
1
2
3
4
5
SNS_AB
VSEN_3.3V
SNS_INK
GND
Ink tank sensor signal
IN
OUT
IN
Ink tank sensor power supply
Ink sensor signal
Ground
-
INK_PWM
Ink tank sensor signal
IN
J503 (Power Supply Unit)
No.
Input /
Output
Signal name
Function
1
2,4
3
VM
Motor power supply +32V
Ground
OUT
-
GND
VH
Head power supply +24V
Power supply control signal
IN
5
PW_DWN
OUT
J505 (ASF_PE Sensors)
No.
Input /
Output
Signal name
Function
1
2
3
4
SES_ASF
SES_PE
GND
ASF sensor
IN
IN
PE sensor
Ground
-
VSEN_3.3V
Sensor power supply +3.3V
OUT
J507 (Main Cam Sensor)
No.
1
Signal name
Function
Input /Output
VSEN_3.3V
GND
Sensor power supply +3.3V
Ground
OUT
-
2
3
SNS_MAIN_CAM
Main cam sensor
IN
3-4
Download from Www.Somanuals.com. All Manuals Search And Download.
J601 (Operation Panel / LCD)
No.
Input /
Output
Signal name
Function
1
2
GND
Ground
-
PANEL_RSTX
GND
Panel reset signal
Ground
OUT
-
3
4
PANEL_INT
+3.3V
Panel interruption signal
LCD drive power supply +3.3V
LV clock-
IN
5
OUT
OUT
OUT
OUT
OUT
OUT
-
6
LVCLK-
LVCLK+
5V
7
LV clock+
8
Power supply +5V
LV data-
9
LVDATA-
LVDATA+
GND
10
11
12
13
14
15
16
17
18
LV data+
Ground
RXD
Reception signal
Transmission signal
Alarm LED
IN
TXD
OUT
IN
ERROR_LED
POWER_LED
STOP_SW
POW_SW
GND
Power LED
IN
Stop/Reset switch
Power switch
Ground
IN
IN
-
J701 (Carriage Motor)
No.
Input /
Output
Signal name
Function
1
2
CR_M
CR motor+
CR motor-
OUT
OUT
CR_MN
J702 (LF Motor)
No.
Input /
Output
Signal name
Function
1
2
LF_M
LF motor+
LF motor-
OUT
OUT
LF_MN
J703 (Purge Unit Motor)
No.
Input /
Output
Signal name
Function
1
2
3
4
PG_MA
PG_MB
PG motor phase A+
PG motor phase B+
PG motor phase A-
PG motor phase B-
OUT
OUT
OUT
OUT
PG_MAN
PG_MBN
3-5
Download from Www.Somanuals.com. All Manuals Search And Download.
J704 (Scanner Motor)
No.
Input /
Output
Signal name
SC_MAN
Function
Scanner motor phase A-
1
2
3
4
OUT
OUT
OUT
OUT
SC_MA
SC_MB
SC_MBN
Scanner motor phase A+
Scanner motor phase B+
Scanner motor phase B-
J801 (Scanner Unit)
Signal name
No.
1
Function
GND
Digital ground
LED drive signal （Red）
LED drive signal （Green）
LED drive signal （Blue）
LED power supply
Clock output
2
LED_R
LED_G
LED_B
LED_Vｃｃ
XPH1
3
4
5
6
7
XTG
SH output
CIS reference power supply
CIS power supply
Digital ground
8
REV_V
Vcc(3.3V)
GND
9
10
11
XPH2（RES_SEL)
CIS resolution switch
J901 (Memory Card)
No.
Input /
Output
Signal name
Function
1
2
+3.3V
D-
Drive power supply +3.3V
D- signal
OUT
BUS
BUS
-
3
D+
D+ signal
4
GND
Ground
5
DOOR
CARD_RST
CARD_INT
GND
Cover switch signal
Card reset signal
Card interruption signal
Ground
IN
6
OUT
IN
7
8
-
IrDA reception signal
IrDA transmission signal
Drive power supply +5.0V
9
IR_RXD
IR_TXD
+5.0V
VBUS
D-
IN
10
11
12
13
14
15
IN
OUT
OUT
BUS
BUS
-
PictBridge VBUS power supply
D- signal
D+
D+ signal
S_GND
System ground
3-6
Download from Www.Somanuals.com. All Manuals Search And Download.
J902 (USB 2.0 I/F)
Input /
Output
No.
Signal name
SNS_USB
Function
1
2
3
4
5
6
7
8
USB VBUS power supply sensor
USB D- signal
USB D+ signal
Ground
IN
D-
BUS
D+
BUS
GND
-
-
-
-
-
L_GND
L_GND
L_GND
L_GND
Logic ground
Logic ground
Logic ground
Logic ground
To the table of contents
To the top
<Part 3: 2. CONNECTOR LOCATION AND PIN LAYOUT; 2-1. Logic Board Ass'y>
3-7
Download from Www.Somanuals.com. All Manuals Search And Download.
2-2. Card Slot Board
J1 (Logic Board)
No.
Signal name
Function
Input / Output
1
2
GND
Ground
-
IN/OUT
IN/OUT
IN
DSC D+
DSC D-
VBUS
+5.0V
Ir_TXD
Ir_RXD
GND
Camera Direct D+ signal
Camera Direct D- signal
PictBridge VBUS power supply
Power supply
3
4
5
IN
6
IrDA reception signal
IrDA reception signal
Ground
IN
7
OUT
-
8
9
INTX
Interruption signal
Reset signal
OUT
IN
10
11
12
13
14
15
RESETX
COVER
GND
Cover switch signal
Ground
OUT
-
D+
D+ signal
IN/OUT
IN/OUT
IN
D-
D- signal
+3.3V
Logic power supply
J2 (SmartMedia, Memory Stick, SD (MMC))
Input / Output
入出力
No.
Signal name
SD_WPSW
Function
1
2
3
4
5
6
7
8
9
SD write protect
IN
-
SD_WP_GND
SD_CD
SD write protect ground
SD card detect
OUT
-
SD card detect ground
SM card detect
SD_CD_GND
SM_CDSW
SM_CDSW_GND
SM_VCC
OUT
-
SM card detect ground
SM logic power supply
SM card detect
OUT
OUT
IN/OUT
SM_CDX
SM_D4
SM 16 bit data bus
3-8
Download from Www.Somanuals.com. All Manuals Search And Download.
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
SM ground
SM_GND
SM_D5
-
SM 16 bit data bus
SM 16 bit data bus
SM 16 bit data bus
SM 16 bit data bus
SM 16 bit data bus
SM 16 bit data bus
SM low voltage detection
SM 16 bit data bus
MMC/SD 16 bit data bus
MS ground
IN/OUT
SM_D3
IN/OUT
SM_D6
IN/OUT
SM_D2
IN/OUT
SM_D7
IN/OUT
SM_D1
IN/OUT
SM_LVD
SM_D0
IN
IN/OUT
SD_DAT1
MS_GND
SD_DAT0
MS_BS
IN/OUT
-
MMC/SD 16 bit data bus
MS bus state
IN/OUT
IN
SD ground
SD_GND
MS_VCC
SD_CLK
-
MS logic power supply
MMC/SD clock
OUT
IN
MS 16 bit data bus
SD logic power supply
MS 16 bit data bus
SD ground
MS_DIO(D0)
SD_VCC
IN/OUT
OUT
Reserve(D2)
SD_GND
MS_INS
IN/OUT
-
MS insertion detection
MMC/SD command
MS 16 bit data bus
MS system clock
MMC/SD 16 bit data bus
MS logic power supply
MMC/SD 16 bit data bus
MS ground
IN
SD_CMD
Reserve(D3)
MS_SCLK
SD_DAT3
MS_VCC(D1)
SD_DAT2
MS_GND
SM_GND
SM_WPX-IN
SM_BSYX
SM_WEX
SM_REX
SM_ALE
SM_CEX
SM_CLE
IN/OUT
IN/OUT
IN
IN/OUT
IN
IN/OUT
-
-
SM ground
SM write protect
SM busy
IN
IN
IN
IN
IN
IN
IN
OUT
-
SM write enable
SM read enable
SM address latch enable
SM chip enable
SM command latch enable
SM logic power supply
SM ground
SM_VCC
SM_GND
SM_WPSW
SM_WPSW_GND
Frame_GND
Frame_GND
SM write protect
SM write protect ground
Frame ground
IN
-
-
Frame ground
-
3-9
Download from Www.Somanuals.com. All Manuals Search And Download.
J3 (CompactFlash)
No.
1
Signal name
Function
Input / Output
GND
CF ground
-
2
CF_D3
CF 16 bit data bus
CF 16 bit data bus
CF 16 bit data bus
CF 16 bit data bus
CF 16 bit data bus
CF chip select
IN/OUT
IN/OUT
IN/OUT
IN/OUT
IN/OUT
OUT
-
3
CF_D4
4
CF_D5
5
CF_D6
6
CF_D7
7
CF_CS0X
GND(CF_A10)
GND(CF_ATASELX)
GND(CF_A9)
GND(CF_A8)
GND(CF_A7)
VCC
8
Ground (CF 24 bit address bus)
Ground (CF output enable)
Ground (CF 24 bit address bus)
Ground (CF 24 bit address bus)
Ground (CF 24 bit address bus)
CF logic power supply
Ground (CF 24 bit address bus)
Ground (CF 24 bit address bus)
Ground (CF 24 bit address bus)
Ground (CF 24 bit address bus)
CF 24 bit address bus
CF 24 bit address bus
CF 24 bit address bus
CF 16 bit data bus
9
-
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
-
-
-
OUT
-
GND(CF_A6)
GND(CF_A5)
GND(CF_A4)
GND(CF_A3)
CF_A2
-
-
-
IN/OUT
IN/OUT
IN/OUT
IN/OUT
IN/OUT
IN/OUT
IN/OUT
OUT
OUT
IN/OUT
IN/OUT
IN/OUT
IN/OUT
IN/OUT
OUT
IN
CF_A1
CF_A0
CF_D0
CF 16 bit data bus
CF_D1
CF 16 bit data bus
CF_D2
CF_IOCS16X
CF_CD2X
CF_CD1X
CF_D11
Not used
CF card detect
CF card detect
CF 16 bit data bus
CF 16 bit data bus
CF_D12
CF 16 bit data bus
CF_D13
CF 16 bit data bus
CF_D14
CF 16 bit data bus
CF_D15
CF_CS1X
CF_VS1X
CF_IORDX
CF_IOWRX
VCC(CF_WEX)
CF_INTRQ
VCC
CF chip select
CF voltage sense
CF read strobe input - output
CF write enable input - output
CF logic power supply (write enable)
CF interruption
IN/OUT
IN/OUT
IN
IN
CF logic power supply
CF ground (chip select)
CF voltage sense
OUT
-
GND(CF_CSELX)
CF_VS2X
IN
3-10
Download from Www.Somanuals.com. All Manuals Search And Download.
CF reset
41
42
43
44
45
46
47
48
49
50
51
52
CF_RESETX
CF_IORDY
CF_INPACKX
VCC(CF_REGX)
CF_DASPX
CF_PDIAGX
CF_D8
IN
CF ready input - output
Not used
IN/OUT
IN
CF register select
Not used
OUT
-
Not used
-
CF 16 bit data bus
CF 16 bit data bus
CF 16 bit data bus
CF logic ground
Not used
IN/OUT
CF_D9
IN/OUT
CF_D10
IN/OUT
GND
-
-
-
PEG(FGND)
PEG(FGND)
Not used
J4 (Digital Camera Connector)
No.
Signal name
Function
Input / Output
1
DSC_VBUS
DSC D-
PictBridge VBUS power supply
Camera Direct D- signal
Camera Direct D+ signal
Ground
OUT
2
3
IN/OUT
DSC D+
IN/OUT
4
DSC_SGND
DSC_FGND
-
-
5 to 8
Ground
J5 (IrDA Board)
No.
1
Signal name
Function
Logic power supply
IrDA reception signal
IrDA reception signal
Ground
Input / Output
Ir_3.3V
Ir_RXD
Ir_TXD
Ir_GND
Ir_FGND
OUT
2
IN
3
OUT
4
-
-
5
Ground
J301 (Memory Card Board)
No.
Signal name
Ir_3.3V
Ir_RXD
Function
Logic power supply
IrDA reception signal
IrDA reception signal
Ground
Input / Output
1
2
3
4
5
IN
OUT
IN
-
Ir_TXD
Ir_GND
Ir_FGND
Ground
-
To the table of contents
To the top
<Part 3: 2. CONNECTOR LOCATION AND PIN LAYOUT; 2-2. Card Slot Board>
3-11
Download from Www.Somanuals.com. All Manuals Search And Download.
2-3. Operation Panel Board
J1 (Logic Board)
No.
1
Signal name
Function
Input / Output
DGND
Ground
-
OUT
OUT
IN
2
POWER_SW
STOP/RESET_SW
LED_POW
LED_ERR
PN_RXD
PN_TXD
DGND
Power switch
3
Stop/Reset switch
Power LED display
Error LED display
Transmission signal
Reception signal
Ground
4
5
IN
6
OUT
IN
7
8
-
9
LVDATA+
LVDATA-
+5V
LCD data signal+
LCD data signal-
Power supply
IN
10
11
12
13
14
15
16
17
18
IN
IN
LVCLK+
LVCLK-
+3.3V
LCD clock signal+
LCD clock signal-
Logic power supply
IN
IN
IN
PNL_INT
DGND
Panel interruption signal
Ground
OUT
-
PNL_RSTX
DGND
Panel reset signal
Ground
IN
-
J2 (LCD Unit)
No.
1
Signal name
LED_SHDNX
LED_POW
VDD
Function
Input / Output
OUT
OUT
OUT
-
Backlight-on operation enable
Power supply
Power supply
Ground
2
3
4
Vｓｓ
5
LED_Vｓｓ
DB7
Ground
-
6
Display data 7
Display data 6
Display data 5
Display data 4
Display data 3
Display data 2
Display data 1
Display data 0
Write signal
OUT
OUT
OUT
OUT
OUT
OUT
OUT
OUT
OUT
OUT
OUT
OUT
OUT
7
DB6
8
DB5
9
DB4
10
11
12
13
14
15
16
17
18
DB3
DB2
DB1
DB0
WDB
RS0
Register select signal
Reset signal
RSTB
CS1B
Chip select signal
Power supply
RDB
To the table of contents
To the top
<Part 3: 2. CONNECTOR LOCATION AND PIN LAYOUT; 2-3. Operation Panel Board>
3-12
Download from Www.Somanuals.com. All Manuals Search And Download.
2-4. Carriage Board
No.
Signal name
A_GNDH
Function
1,2
3
Head ground
HD2_C1
HD8_Y1
VSS
Head data C1
4
Head data Y1
5
Logic ground
6
PBK1
Logic ground
7,8
9
B_GNDH
HD3_SC1
HD5_SM1
HD4_M1
HENB1
HD10_SM2
VSS
Head ground
Head data SC1
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27,35
28
29
30
31
32,40
33,34
36
37
38
39
Head data SM1
Head data M1
Head heat enable signal 1
Head data SM2
Logic ground
HD11_M2
B_DiK
Head data M2
Logic ground
HD0_K1
HENB0
HENB3
HLAT
Head data BK1
Head heat enable signal 0
Head heat enable signal 3
Head data latch signal
Head data SC2
HD12_SC2
PBK2
Logic ground
HD9_Y2
HENB2
HD1_K2
A_DiK
Head data Y2
Head heat enable signal 2
Head data BK2
Logic ground
HVDD
Head logic power supply +3.3V
Head EEPROM chip select signal
Head data transfer clock signal
Head EEPROM data signal
Head data C2
ROM_CS
HCLK
ROM_DO
HD13_C2
B_VH2
A_VH
Head drive power supply +24V
Head logic power supply +24V
Head EEPROM serial clock signal
Head EEPROM data signal
Diode senor anode
Head drive power supply +24V
ROM_SK
ROM_DIO
B_DiA
VHT
To the table of contents
To the top
<Part 3: 2. CONNECTOR LOCATION AND PIN LAYOUT; 2-4. Carriage Board>
3-13
Download from Www.Somanuals.com. All Manuals Search And Download.
3. PIXMA MP510 SPECIFICATIONS
<Machine>
Type
Desktop serial color inkjet printer
Auto sheet feed (auto sheet feeder, front feeder)
4,800 x 1,200dpi (Max.)
Paper feeding method
Resolution
- 4 x 6, borderless printing: Approx. 47 sec. (PP-101 4x6, borderless printing, default settings)*
For reference:
Custom 5
Black (Fine Black) 25ppm
Color (Fine Color) 17ppm
Standard
13.9ppm
10.4ppm
Remarks
Paper feeding from the ASF
Paper feeding from the ASF
Throughput (target value)
* Based on Canon standard pattern. Print speed may vary depending on system configuration, interface,
software, document complexity, print mode, page coverage, type of paper used and does not take into
account data processing time on host computer.
Note: Notations for the Americas should be confirmed with the related marketing section of each sales
company in the Americas.
Printing direction
Print width
Bi-directional, uni-directional
Max. 203.2mm (215.9mm in borderless printing)
- Computer: USB 2.0 Hi-Speed, Bluetooth ver. 1.2 (optional)
Interface
- Camera Direct: PictBridge with a PictBridge-supported digital camera and digital video camera
- Mobile phone: IrDA 1.2, Bluetooth ver. 1.2 (optional), both for JPEG files only
Stacking
capacity
Max. 13 mm (Approx. 150 sheets of 64 g/m2 plain paper)
64 to 105 g/m2, Canon specialty paper 273 g/m2 at the maximum
Paper weight
Type
Size
Stacking capacity (sheets)
Plain paper
Approx. 150 (13mm)
Legal
10
Super White Paper
High Resolution Paper
Photo Paper Pro
SW-201
HR-101N
PR-101
A4, Letter
A4, Letter
A4, Letter, 8x10
4x6, 4x8, Wide
A4, Letter, 5x7
4x6
Approx. 100 (13mm)
Approx. 80
10
20
10
20
10
20
10
20
10
20
10
20
1
ASF paper
feed
specifications
Photo Paper Plus Glossy
PP-101
Photo Paper Plus Semi-gloss SG-201/101 A4, Letter, 8x10
4x6
Paper
specifications
Glossy Photo Paper
Matte Photo Paper
GP-401
A4, Letter
4x6, Credit Card
GP-501/502 A4, Letter
4x6
MP-101
A4, Letter
4x6
Photo Paper Plus Double Sided PP-101D
A4, Letter, 5x7
Photo Stickers
T-shirt Transfer
Envelope
PS-101
TR-301
4x6
1
A4
1
DL-size, COM#10
10
Stacking
capacity
Max. 10 mm (Approx. 100 sheets of 64 g/m2 plain paper)
64 to 105 g/m2
Front feeder
paper feed
Paper weight
specifications
Paper
Plain paper (10 mm or less, approx. 100 sheets): A4, B5, Letter only
specifications
Scanning unit open, Presence of print head / ink tanks, Remaining ink amount (optical / dot count), Ink
tank position, Paper presence, Paper end sensor, Ink amount in the ink absorber, Internal temperature,
Paper lifting plate position, Paper feed roller position, Carriage position, Supported camera direct printing
device, Presence of memory card, Scanner home position
Detection functions
Download from Www.Somanuals.com. All Manuals Search And Download.
3-14
- Printing from a computer:
36 dB (A) (Photo Paper Pro, highest print quality settings, paper feeding from the ASF)
- Copying:
Acoustic noise
38.5 dB (A) (Photo Paper Pro, highest copy quality settings, paper feeding from the ASF)
During operation
Temperature
Humidity
5C to 35C (41F to 95F)
10%RH to 90%RH (no condensation)
0C to 40C (32F to 104F)
Environmental requirements
Non operation
Temperature
Humidity
5%RH to 95%RH (no condensation)
Power consumption
Power-off*2
Power supply voltage, frequency
AC 100 to 240V, 50/60Hz
Standby
(copy)*1
Approx.25W
Approx. 2.0W
Approx. 0.8W
Power supply
*1: When copying ISO/JIS-SCID N2 on A4 plain paper with the standard settings
*2: Scanner light turned off
- With the trays retracted: Approx. 444 (W) x 365 (D) x 171 (H)mm
- With the trays extended: Approx. 444 (W) x 627 (D) x 297 (H)mm
- With the scanning unit opened (max.): Approx. 444 (W) x 627 (D) x 435 (H)mm
External dimensions
Weight
Approx. 7.0 kg, including the print head and excluding the optional units
Electromagnetic radiance:
VCCI, FCC, IC, CE Mark, Taiwan RPC, C-Tick, CCC (EMC), Korea MIC, Gost-R
Electrical safety:
Related standards
(Machine)
Electrical Appliance and Material Safety Law (DENAN), UL, C-UL, CB Report, CE Mark, GS, Gost-
R, FT, SASO, CCC, SPRING, Korea EK, IRAM (Argentine)
Environmental regulations:
RoHS (EU), WEEE (EU), Korea Package Recycle Law, Green Point (Germany), Energy Star, Eco
Mark, Law on Promoting Green Purchasing
Serial number location
The label is attached to the spur guide inside the printer.
Available (detection by optical method and dot count, enabled at default)
Not available
Remaining ink amount
detection
Paper type detection
Available
Print head alignment
- Automatic alignment: Perform via the operation panel, using the Print Head Alignment Sheet.
- Manual alignment: Perform via the operation panel, or from the MP driver Maintenance tab.
<Scanner>
Type
Flat bed scanner (scanning of a fixed document by a moving scanner head)
CIS (Contact Image Sensor)
Sensor type
Optical resolution
1,200 x 2,400 dpi (max.)
Scanning resolution (software
interpolation)
19,200 x 19,200 dpi (max.)
Grayscale: 16 bit / 8 bit
Gradation (input / output)
Document size
Color: 48 bit / 24 bit (RGB each color 16 bit / 8 bit)
Platen glass: A4 / Letter (Max.)
<Copy>
Copy quality
Intensity
3 levels (Fast, Standard, High)
9 levels (automatic intensity adjustment available)
Enlargement / reduction ratio 25 to 400%
A4 color document: Approx. 33 sec.
For reference:
- Monochrome copy: 25cpm
Copy speed
- Color copy: 17cpm
Note: - Document copy speed is based on copying the manuscript "ISO/IEC FCD24712:
Newsletter" (digital data printed by offset) using default settings on plain paper. Black text / color
(CPM) are based on "fast mode" setting using Canon standard pattern on plain paper. Copy speed
Download from Www.Somanuals.com. All Manuals Search And Download.
3-15
may vary depending on document complexity, copy mode, page coverage, type of paper used, etc. and
does not take into account warming up time.
- Notations for the Americas should be confirmed with the related marketing section of each sales
company in the Americas.
Document size
A4 / Letter (max.)
Preset ratio:
max. (400%), 4x6 -> LTR (212%), 5x7 -> LTR (170%), A5 -> A4 (141%), B5 -> A4 (115%), A4 ->
LTR (95%), A4 -> B5 (86%), A4 -> A5 (70%), min. (25%)
Enlargement / reduction
Zoom:
25 to 400% (in increments of 1%)
Number of continuous copies Monochrome / color: 1 to 99 copies
<Direct printing>
Compact Flash TYPE I/II (3.3V), Microdrive, SmartMedia Card (3.3V only, 1MB and
2MB not supported), Memory Stick, Memory Stick PRO, SD card, MultiMedia Card
(ver. 3.31), xD-Picture Card*, miniSD card*, Memory Stick Duo*, RS-MMC (ver.
3.31), Memory Stick PRO Duo*
Memory card drive
Storage function
Supported memory card
* Adapter required.
Operation
Condition
Function
Via the machine buttons.
Before changing the settings, the memory card must be removed.
Read / Write
File format
Print quality
JPEG (DCF, CIFF, Exif 2.21 or prior, JFIF), DPOF compliant
Standard, High
Image correction
function
VIVID, Photo Optimizer PRO, Noise reduction, Face brightener, Image optimizer
Brightness, contrast, color hue (skin tones)
Not available
Image adjustment
function
Image processing
function
Image retrieval function Not available
Ver. 1.00 compliant
DPOF
Index printing, printing of an image the specified number of copies, printing of the
specified image(s), printing with the shooting date
Single-photo/multi-photo/all-photo printing:
1 photo per page (borderless/with borders, only with borders for plain paper)
Index printing:
6, 15, 24, 35, 80 photos per page
Card Direct Printing
72 photos per page (for 8x10)
Layout printing:
Print layout
2, 4, 8 photos per page (borderless/with borders)
Half (borderless/with borders, with/without lines)
Album (4 photos per page, right/left)
Mix 3 types (for A4/LTR)
Sticker printing:
16 stickers
Information print
Throughput
Shooting date, file number
Approx. 55 seconds (4" x 6" borderless)
Note: - When printing a 6 megapixel image taken by certain Canon digital camera from
a memory card on default settings using Photo Paper Plus Glossy without
border. Actual print speed may vary depending on image data, print mode, type
of paper and type of memory card used.
- Notations for the Americas should be confirmed with the related marketing
section of each sales company in the Americas.
- Default (selections based on the machine settings)
- 4" x 6"
Photo Paper Pro, Photo Paper Plus Glossy, Photo Paper Plus Semi-gloss, Glossy
Photo Paper, Photo Stickers*1
Download from Www.Somanuals.com. All Manuals Search And Download.
3-16
- 5" x 7"
Photo Paper Pro, Photo Paper Plus Glossy, Photo Paper Plus Semi-gloss, Glossy
Photo Paper
- Credit Card
Glossy Photo Paper
- 8" x 10"
Photo Paper Pro
- A4 / Letter
Supported paper size
Photo Paper Pro, Photo Paper Plus Glossy, Photo Paper Plus Semi-gloss, Glossy
Photo Paper, plain paper
*1: Canon-brand sticker.
- Default (selections based on the machine settings)
- Photo: Photo Paper Plus Glossy, Glossy Photo Paper
- Fast Photo: Photo Paper Pro
Supported paper type
- Plain paper: A4 / Letter plain paper
- Default (selections based on the machine settings, borderless/with borders)
- 2 photos per page (borderless/with borders)
- 4 photos per page
Camera Direct Printing
(PictBridge)
Print layout
- 9 photos per page
- 16 photos per page
- Layout specific to Canon Photo Stickers
Trimming
Follows a connected PictBridge device settings.
Default (selections based on the printer settings), ON, OFF, VIVID*, NR (Noise
Reduction)*, VIVID + NR*, Face brightener
Image optimization
* Available only with a Canon PictBridge camera.
Date / file number print Follows the settings specified in a connected PictBridge device.
Approx. 57 seconds (4" x 6" borderless)
Note: - When printing a 6 megapixel image taken by certain Canon digital camera from
PictBridge on default settings using Photo Paper Plus Glossy without border.
Actual print speed may vary depending on image data, print mode, type of paper
used and device that the printer is connected to.
Throughput
- Notations for the Americas should be confirmed with the related marketing
section of each sales company in the Americas.
Download from Www.Somanuals.com. All Manuals Search And Download.
3-17
<Print head>
Type
Single head with 4 removable ink tanks (each color)
Pigment-based BK:
320 nozzles, 600 dpi, 30 pl
Print head
Dye-based C / M / Y:
256 x 5 nozzles, 1,200 dpi, 2 pl / 5 pl (C / M), 5 pl (Y)
Pigment-based black
Ink color
Ink tank
Dye-based cyan, magenta, yellow
Japan: BCI-9BK (pigment-based), BCI-7eC / M / Y (dye-based)
Others: PGI-5BK (pigment-based), CLI-8C / M / Y (dye-based)
Print head, approx. 48g
Weight (Net)
Supply method
Part number
As a service part (not including ink tanks)
QY6-0070-000
<Supported ink tanks>
Pigment-based ink
PGI-9BK BCI-5BK
Dye-based ink
Model name and
destination
BCI-7eC
O
BCI-7eM
O
BCI-7eY
O
CLI-8C
X
CLI-8M
X
CKI-8Y
X
PIXUS MP510 Japan
O
X
PIXMA
Others
X
O
X
X
X
O
O
O
MP510
O: Usable
X: Not usable
Note: The ink tanks for the Japanese models are not compatible with those for the non-Japanese models. Be sure to use the appropriate
ink tanks in servicing.
To the table of contents
To the top
<Part 3: 3. PIXMA MP510 SPECIFICATIONS>
Download from Www.Somanuals.com. All Manuals Search And Download.
3-18
|