CAUTION:
READ THIS MANUAL CAREFULLY
BEFORE OPERATING YOUR NEW
CANNON® DOWNRIGGER. ®
RETAIN FOR FUTURE REFERENCE.
EASI-TROLL hS
EASI-TROLL /E
LAKE-TROLL
NOTE: Do not return your CANNON® Downrigger to
your retailer. Your retailer is not authorized to repair or
replace this unit. You may obtain service by:
•
•
calling CANNON® at 1-800-227-6433;
returning your downrigger to the Factory Service
Center;
•
sending or taking your downrigger to any
CANNON® Authorized Service Center on
enclosed list.
Please include proof of purchase, serial number
and purchase date for warranty service with any of
the above options.
OWNER’S MANUAL
Introduction to Downriggers
Mounting Your Downrigger
Attaching the Crank Handle
Terminator & Line Release
Cannon Uni-Release
pg. 2
pg. 2-7
pg. 8
pg. 9
pg. 9
The Effects of Blowback
Maintaining Your Downrigger
Troubleshooting
pg. 12
pg. 13
pg. 13
pg. 14
pg. 15
pg. 15
See List
Trolling Tips
Warranty Information
Cannon Service Policy
Authorized Service Centers
Attaching the Rod Holder
Operating Your Downrigger
pg. 10
pg. 11
Download from Www.Somanuals.com. All Manuals Search And Download.
Downrigger Mounting on Boats
Arrows Indicate
A downrigger should be mounted where ever it
is easy to operate and observe. You want to be
able to see your fishing rod and to react quickly.
So, choosing a good spot to mount your
downrigger on your boat is 99% of the job.
Due to the great variety of boats available,
mounting your downrigger can be a dilemma.
Having proper mounting accessories is essential.
Cannon has a complete line of mounting
accessories to conveniently mount your
downriggers on any boat.
Mounting Locations
Deck Plate
Mounting Accessories
Deck Plates are necessary when extra
strength must be added to the base material of
the boat and for attaching the downrigger to other
mounting accessories.
Gimbal Mounts are designed to fit medium-
sized flush mounted rod holders built into the
gunwale of many larger fishing boats and
cruisers. Only sturdy, high quality rod holders
should be used for this temporary mounting
system. Gimbal mounts are available in 9" or 12"
post lengths.
Gimbal Mount
Clamp Mounts can be mounted at the
junction of two rail sections with the aid of two ¼"
pieces of plywood. They will protect your rail from
any marks from the clamp and provide a non-slip
surface.
Clamp Mount
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Side Rail Mounting
Side/Rail on T-Section
Side/Rail mounts can be mounted to a welded
T-section. It can also be used at the two rail
section butt joint. In both installations it is
recommended to use a non-slip material, such as
rubber or a thin wood sheet, between metal
surfaces.
You can also use these for mounting to a very
narrow side gunwale. There is a plate provided for
back-up with bolts and washers. If the gunwale
compartment is foamed in, then wellnuts should
be used. It is also recommended to install two
additional flat head screws through the top plate
for stabilization (you will need to drill and
countersink).
Side/Rail on Gunwale
NOTE: In no case should this mount be used
on fiberglass ¼" thick or less unless it is
foamed in.
Pedestal Mounting
Pedestals are used wherever additional height is
needed for ease of operation or to clear
obstructions, such as handrails.
Caution: When using a pedestal mount or
side/rail mount, do not extend the telescopic
boom on your Easi-Troll HS \ Lake-Troll. The
increased leverage will cause excessive
strain and possible failure of the mount.
Pedestal for Additional Height
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the Base on Your Boat
Decks up to 7/16" thick
Stern
Facing
Outboard
Facing
Where access to the underside of the deck is
not available, the mounting base can be mounted
using wellnuts. Use the base as a template to
mark locations and drill four 1/2" holes. Mount the
base using four 1/4"-20 x 1 1/2" truss head screws
and four wellnuts. Tighten the screws so the
wellnuts are firmly compressed as pictured.
Rear
or
Stern
Note Locking
Slots in Base
Side
or
Decks thicker than 7/16"
Gunwale
For decks thicker than 7/16", or where the
underside of the deck is accessible, mount the
base with screws, nuts, and washers. Use the
base as a template to mark the locations and drill
four 9/32" holes. Use four 1/4" -20 x 2 1/2" truss
head screws and four each flat washers, lock
washers, and nuts. Fasten the base to the deck as
pictured.
Decks
up to
7/16"
Thick
Base
NOTE: Wellnuts cannot be used on decks thicker
than 7/16".
Wellnuts
Base
Decks Thicker Than 7/16"
Washer, Lock Washer, and
1/4-20 Hex Nut
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Decks thinner than 1/4"
Where the underside is accessible, mount
the deck plate using screws, nuts, and washers.
Drill 9/32" holes. Use four 1/4”-20 x 2" flat head
screws, nuts and washers (flat and lock). Fasten
plate to deck as pictured. To secure the low-
profile base to the deckplate use four 1/4”-20 x 1
1/2" truss head screws.
Use a Cannon Deck Plate to prevent
deflection and add stability to decks thinner than
1/4". Use the deck plate as a template to mark the
hole locations.
If access to the underside of the deck is not
available, the deck plate can be mounted using
screws and wellnuts. Drill 1/2" holes. Use four
1/4”-20 x 2" flat head screws and four wellnuts to
mount deck plate as pictured. Tighten the screws
so the wellnuts are firmly compressed.
Cannon Deck Plate
Deck Up to 7/16" Thick
Base
Deck Thicker Than 7/16"
Washers, Screws,
& Nuts
Wellnut
NOTE: When using the telescopic boom, we strongly recommend the use of a deck plate on all
boats to provide adequate stability for the downrigger.
Low-Profile Swivel Base
To mount the Low-Profile Swivel Base,
Low-Profile Swivel Base
follow the same procedure as for the deck plate
with this exception: use four 1/4"-20 x 1-1/2" truss
head screws to fasten the mounting base and four
additional 1/4"-20 x 2-1/2" truss head screws to
attach the swivel base to the boat deck.
Mounting the Downrigger on the
Base
Slide the bottom of the frame over the lip of the
base, with the boom outboard or facing the stern.
Move the frame over the base until the latch clicks
into place. If properly seated, the frame should
completely cover the base.
CAUTION: If not fully seated, your downrigger can
be dislodged from the base.
Tip: Periodically check base to ensure integrity.
The base should be replaced at least every 5
Latch
years.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Up Your Downrigger
Attaching the Boom
The boom inserts into the downrigger frame.
Be sure that the boom is held securely by seating
it firmly against the shoulder inside the fame and
fastening the boom locking screw (#8 X 1” self
tapping) so that it engages the hole in the boom.
The 3/4"-Long Phillips
Screw Must Engage
Hole in Boom
Assemble Swivel Head To Boom
Spread the swivel head side plates and slip the
assembly over the boom end. Snap the assembly
together and install two #4 x 1/2" screws into the
swivel head.
For Lake-Troll only: On swivel head assembly
with counter leave the corrugated spacer in place
until the assembly is snapped together, remove
the spacer and install the screws.
#4 x 1/2"
Screws (2)
TIP: Adjusting the angle of the boom head can
help control cable wrap on the reel.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Attaching the Crank Handle
Assembly
Make sure the thrust bearing is sandwiched
between its two races. The thrust bearing spring
should be oriented where the narrow end is
toward the bearing. Slide the bearing with races
and spring over the ratchet shaft. Then, carefully
thread the crank handle onto the shaft and
continue turning the handle clockwise until the
clutch is fully tightened
NOTE: Place your fingertip on the edge of the
bearing and races. This allows the crank to be
threaded more easily until the spring puts
resistance on the clutch pad.
Thrust Bearing
Spring
Crank Handle
Races
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Terminating the Downrigger Cable
Examine the top of the terminator and note the
order shown in the detail to run cable.
Unwind about 2 feet of cable
and thread the cable through
the rubber cushion.
Cable
Rubber Cushion
CABLE IN
CABLE IN
Attach to terminator.
CABLE
OUT
Snap &
Swivel
Tip: A set of pliers with wire cutters is
recommended for this part of setup.
TIP: Use only straight cable, not kinked.
Slide the cushion over the top of the
Lead cable into
HOLE A.
terminator and give it a test pull.
Tighten cable
by squeezing
terminator until
it snaps shut.
Then pull at top
and bottom
until drawn
tight. Make
sure that the
cable
Pull six inches of
cable through.
Thread cable
through swivel,
then up into
The cable is set to attach a Cannon
Trolling Weight.
HOLE A
bottom of the
terminator.
Lead cable out of
HOLE B and into
HOLE C. Push
the cable until its
end touches the
inside of the
threads in
groove of
the hook.
Swivel
terminator hook.
Cannon Uni-Release
Close
The Cannon Uni-Release attaches directly to
the downrigger weight. Attach fishing line to the
clip at the end of the release, and then click
through a series of increasing tension settings.
The release can be used with any test line on salt
or fresh water and may be adjusted from 2 to 22
pounds of grip tension on the line.
Tension
Adjust
Open
Fishing Line
Open
To change line release tension, turn tension knob
to (+) to increase or (-) to decrease. Tension also
may vary according to where the line is placed in
the grips. Higher tension is on the line if it is set
back toward the hinge, and lower if set closer to
the opening. To open the release, spread the
release arms with thumb and forefinger applying
pressure to the sides.
Gripper
Pads
9
Download from Www.Somanuals.com. All Manuals Search And Download.
CAUTION: This rod holder is intended for use
of up to 30 lb. test line only, and is not
recommended for use with any tackle IGFA
rated higher than 30 lb. A safety strap (not
included) is recommended for all applications.
Attaching the Rod Holder
The positive lock rod holder incorporates a
locking disk that allows the rod holder to be
aligned in 15 degree increments. Slide the rod
holder tube into the clamp to the desired position
within the recommended area (see below).
Be sure the angled shoulders are facing up.
Place the locking disk into the mating recess of
the frame.
The rod holder assembly is not warranted
when used with tackle above 30 lbs.
Equipment placed in the rod holders and the
loss thereof is the responsibility of the user
and is in no way warranted by JOHNSON
OUTDOORS, INC. Mounting must be in
accordance with the above instructions and
diagram to be warranted.
Slip the clamp arms in place where the
obround tab on the disk fits into the slot on the
clamp. Slide the star washer between the arm of
the clamp and the frame. Place the flat washer
onto the bolt. Then insert the bolt with washer
through the clamp by entering the disk, going
through the frame, the star washer, and out the
other side of the clamp. Tighten the nut to secure
the rod holder. Reposition the rod holder by
loosening the nut and adjusting the tilt.
Single Rod Holder Assembly
Dual Rod Holder Assembly
Star Washer
Placement
Recommended
Area to Clamp
Rod Holder
Angled
Shoulder
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Your Downrigger
After mounting the Cannon downrigger to your
boat, release some line from your rod and reel so
that the lure is anywhere from 5 to 100 feet behind
the boat, this is called drop back. Attach the
fishing line firmly into the line release. Lower the
weight to the desired depth as indicated on the
depth meter. Place the fishing rod in the rod
holder and reel up the slack so that your rod has a
slight bend in it. When a fish strikes the lure, the
line will separate from the release. Then you will
be free to fight the fish and bring it in on your rod
and reel.
To Lower
Weight
Lowering the Weight
To Raise
Weight
You can lower the trolling weight at a controlled
rate by turning the crank handle gently counter-
clockwise (away from the boom). Depending on
how far you turn, you can let your trolling weight
descend as fast or as slowly as you wish. Turn the
crank handle clockwise (toward the boom) until it
you hear a click to stop the weight. This gives you
control to let it plunge rapidly or sink slowly to a
predetermined trolling depth. With multiple
downriggers, you could start all your weights
creeping down, one at a time, and then stop them
each in turn.
Raising the Weight
Turn the crank handle clockwise (toward the
boom) as rapidly as you desire to retrieve the
trolling weight.
Adjusting the Clutch Tension
The clutch is built into the crank mechanism.
Turn crank handle clockwise to increase the drag
and counterclockwise to reduce it.
NOTE: If your reel continues to slip no matter
how hard you tighten the crank, see the
Troubleshooting section of this booklet.
CAUTION: Remove weight from downrigger
before traveling either by water or transporting on
trailer.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Blowback Charts
8-Lb. Weight at 2, 4, and 6 MPH
Blowback
Simply stated, blowback is what happens to
the downrigger weight when you pull it through
the water behind your boat. As your speed
increases, so does the horizontal distance
between the weight and your downrigger. The
faster you go, the farther the weight is behind you.
The farther the weight is behind you, the
shallower the weight is.
The following charts provide you with
blowback information for three sizes of Cannon
downrigger weights pulled at three different
speeds with no lures attached and with no
current. Current drag, water salinity and the use
of non-Cannon products will affect your actual
trolling depth.
2 MPH
4 MPH
6 MPH
As an example, the first chart shows that if you
are trolling at 4 MPH with an 8 pound weight and
you have 100 FT. of cable in the water with no
current; the downrigger ball is actually at a depth
of about 80 FT.
Amount of Cable in Water (ft.)
10-Lb. Weight at 2, 4, and 6 MPH
2 MPH
4 MPH
6 MPH
Amount of Cable in Water (ft.)
12-Lb. Weight at 2, 4, and 6 MPH
2 MPH
4 MPH
6 MPH
12
Amount of Cable in Water (ft.)
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Depth Meter
Depth Meter
The Cannon Depth Meter provides non-slip
accuracy, plus easy resetting. To reset, just slide
the meter away from the reel until the gears are
disengaged. Spin meter gear to change setting.
NOTE: Actual fishing depth may vary from depth
shown on meter due to trolling speed and weight
of cannon ball. (See "Blowback")
Maintaining Your Downrigger
At the beginning of each fishing season and
more often during periods of heavy usage, lightly
grease the thrust bearing, reel shaft bearings,
swivel head pulley, ratchet brake face, and ratchet
dog. When using for saltwater fishing, thoroughly
rinse the entire downrigger with fresh water after
each trip and lubricate on a frequent basis.
Replace the cable at least every two years.
For repairs or servicing your downrigger refer
to the Warranty Information section of this
booklet.
Trouble Shooting
PROBLEM:
Clutch slips
SOLUTION:
The set screw in the reel may have come
loose off the shaft. Follow the instructions
below:
1) Unwind the cable from the reel.
2) Remove the set screw.
3) Align the set screw hole in the reel with the
hole in the reel shaft by inserting a 3/16" or
smaller rod and rotating the reel until you feel
it drop into the shaft hole.
4) Replace the set screw and tighten until you
feel resistance.
5) By gently rocking the reel back and forth while
tightening the set screw, you can feel it
engage in the shaft hole. The half dog point on
the set screw must enter the hole in the shaft;
not just be tightened against the reel shaft.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
5) Locate fish on a vertical plane. Place lures
in areas where fish might be. Skilled fishermen
call these areas the “strike zones”. They include
the edges of the week beds, structure along
bottom, drop-offs, preferred temperature of the
target species, and the thermocline. Remember
that fish occupy certain areas for certain reasons
(sources of food, protective cover, preferred
temperatures, etc.).
Ten Good Trolling Tips
1) Test your lures over the boat side before
sending them down and back. Do this to make
sure the lure wiggles and wobbles properly
without going belly up or wandering off. Some
lures can be adjusted, fine tuned actually, to
impart maximum action. For example, a slight
bend in the tail of a spoon or twist of the hook eye
in the nose of a plug can make a noticeable
difference in how the lure performs.
6) Consider special knots and swivels. A good
ball bearing swivel will all but eliminate line twist
and will aid in getting maximum performance from
a lure. Many anglers add the tiny swivels to split
rings already on the lure itself. On the other hand,
a swivel may dampen the action of a sensitive
lure, such as a Rapala. Some fisherman tie tiny
improved cinch or loop knots. Loop knots in
particular may enhance up and down and side to
side action of lures. Any good fishing manual will
explain how to tie these and other knots.
Also, when running two or more lures, make
sure the offerings are compatible. Lures that run
out of harmony with each other are bound to
tangle and that means wasted time to straighten
out the mess. Testing them first will avoid the
problem.
2) Consider different sizes, shapes, and colors
of lures. No one has ever figured out with
precision what makes a fish strike or snub a lure.
There is no doubt, that matching the forage
(minnows, crayfish, etc.) in color, shape, action,
and size can help trigger those strikes from
hungry fish. On the other hand, if fish such as
bluegills, small mouth bass or Coho salmon are
protecting spawning beds, they may attack
whatever is threatening. So, bright colors in lures
may out produce bland colors.
7) Consider releases for flatline trolling. A
good tip is to secure a piece of downrigger cable
or heavy monofilament to the water ski hook or
handle below the transom of most boats. To the
other end of the mono or cable, add a pinch-r-
release. After letting out your lure to the desire
distance, put the rod in its holder, then bend the
tip and secure the fishing line in the release.
3) Vary trolling speeds. Goosing the engine
now and then or slowing to a crawl every so often
will change the action of the lures and may get
fish to strike them.
8) Add a weed guard. Having trouble with
weeds hanging up lures? Consider tying a three-
inch piece of monofilament a foot above the lure.
Leaves, smaller weeds and other debris may
catch here momentarily then fall off to the side of
the lure without tangling. Weedless lures are
another smart consideration. Downrigger cables
are effective weed catchers when trolling for pike,
muskies, or bass in weed-infested lakes.
4) Vary trolling patterns and lead lengths. The
amount of line you let out often determines how
deep the lure will run and, to some extent, what
degree of action it will impart. For starters,
consider running lures about ten feet behind
downrigger weights. If flat line trolling, put them
back about fifty feet, then experiment depending
on what the fish do.
9) Add a stinger hook. When fish short strike,
slap at lures without becoming hooked, adding a
stinger hook can solve the problem. Simply tie a
treble hook to one end of a four inch piece of
monofilament and then tie the extra hook to the
last gang of hooks on your lure. The stinger hook,
which trails the lure, provides extra insurance.
Trolling patterns affect lure action too, that is
why some anglers like to wheel a lazy S course.
On turns, outside lures will speed up momentarily
while inside lures hang for a moment or two. Fish
may nail lures that change speeds. Also, zigzag
patterns allow for more water coverage, plus it
keeps lures out of propeller boil, an important
consideration for browns and other wary species.
10) Keep hooks sharp. Some of the best
fishermen sharpen all hooks after every fish
caught. Hooks get dull through both use and
misuse, and probably more fish are lost to dull
points than anything else.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
CANNON® SERVICE POLICY
AFTER THE APPLICABLE WARRANTY PERIOD
CANNON® LIMITED WARRANTY
Johnson Outdoors Inc. warrants to the original purchaser that if
the accompanying product (see exclusions below) proves to be
defective in material or workmanship within the following warranty
periods, Johnson Outdoors Inc. will, at its option, either repair or
replace same without charge (but no cash refunds will be made):
1) The boom, motor, and reels, plus all Lexan®* parts, including
but not limited to frames and bases, will be free from defects
in materials and workmanship, subject to normal wear and
tear, for the original purchaser's lifetime.
After the applicable warranty period, or, if one of the above
exclusions applies, Cannon® products will be repaired for a charge of
parts plus labor. All factory repairs, after the applicable warranty
period, carry a 90-Day Limited Warranty, subject to the exclusions
and limitations stated above.
TO ENFORCE WARRANTY OR TO
OBTAIN REPAIRS AFTER WARRANTY
2) All other items will have 1-year limited warranties from the
date of original retail purchase, except THE FOLLOWING
ITEMS THAT HAVE NO WARRANTY WHATSOEVER: boot
covers, clothing, Dacron line, rubber bands, swivel lock pin,
weights, and wire cable.
This limited warranty may be enforced only by the original
purchaser; all subsequent purchasers acquire the product "as
is" without any benefit of this limited warranty. Repair or
replacement of the product as set forth in this limited warranty
shall be the original purchaser’s sole and exclusive remedy
and Johnson Outdoors Inc.’s sole and exclusive liability for
breach of this warranty.
To obtain warranty service in the U.S., the downrigger or part
believed to be defective and the proof of original purchase (including
the date of purchase) must be presented to a Cannon® Authorized
Service Center or to Cannon®’s factory service center in Mankato,
MN. Except as noted below, any charges incurred for service calls,
transportation or shipping/freight to/from the Cannon® Authorized
Service Center or Cannon®’s factory, labor to haul out, remove, re-
install or re-rig products for warranty service, or any similar items are
the sole and exclusive responsibility of the purchaser. Downriggers
purchased outside of the U.S. (or parts of such downriggers) must be
returned prepaid with proof of purchase (including the date of
purchase and serial number) to any Authorized Cannon® Service
Center in the country of purchase. Warranty service can be arranged
by contacting a Cannon® Authorized Service Center listed on the
enclosed sheet, or by contacting the factory at 1-800-227-6433 or
Fax 1-800-527-4464. If the necessary repairs are covered by the
warranty, we will pay the return shipping charges to any destination
within the United States.
EXCLUSIONS
This warranty does not apply in the following circumstances:
• When the product has been connected, installed, combined,
altered, adjusted, serviced, repaired, or handled in a manner
other than according to the instructions furnished with the
product
• When any defect, problem, loss, or damage has resulted from
any accident, misuse, negligence, carelessness, or abnormal
use, or from any failure to provide reasonable and necessary
maintenance in accordance with the instructions of the
owner's manual
DO NOT return your Cannon® downrigger or parts to your retailer.
Your retailer is not authorized to repair or replace them.
Major parts, such as the motor and main frame, must be returned
to Johnson Outdoors Inc. in Mankato, Minnesota, or a Cannon®
Authorized Service Center, for repair or replacement. To reduce
shipping costs, we suggest removal of loose parts such as the boom
and rod holders. Small parts that can be easily removed such as the
handle and/or the counter, may be removed from the downrigger and
returned for repair or replacement.
LIMITATION AND EXCLUSION OF IMPLIED WARRANTIES AND
CERTAIN DAMAGES
THERE ARE NO EXPRESS WARRANTIES OTHER THAN
THESE LIMITED WARRANTIES. JOHNSON OUTDOORS INC.
DISCLAIMS LIABILITY FOR INCIDENTAL AND CONSEQUENTIAL
DAMAGES, AND IN NO EVENT SHALL ANY IMPLIED
Retain your sales receipt! Proof of purchase must accompany
product when returned.
WARRANTIES (EXCEPT ON THE BOOM, MOTOR, REELS, AND
ALL LEXAN®* PARTS), INCLUDING ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR PARTICULAR PURPOSE,
EXTEND BEYOND ONE YEAR FROM THE DATE OF PURCHASE
(AND IN THE CASE OF THE BOOT COVERS, CLOTHING,
DACRON LINE, RUBBER BANDS, SWIVEL LOCK PIN, WEIGHTS,
AND WIRE CABLE, JOHNSON OUTDOORS INC. DISCLAIMS ALL
IMPLIED WARRANTIES). THIS WRITING CONSTITUTES THE
ENTIRE AGREEMENT OF THE PARTIES WITH RESPECT TO THE
SUBJECT MATTER HEREOF; NO WAIVER OR AMENDMENT
SHALL BE VALID UNLESS IN WRITING SIGNED BY JOHNSON
OUTDOORS INC.
Return Address:
Johnson Outdoors Inc.
Cannon Division
121 Power Drive
Mankato, MN 56001
FOR YOUR INFORMATION:
Serial No.
Date Purchased
Store Where Purchased
Some states do not allow limitations on how long an implied warranty
lasts or the exclusion or limitation of consequential damages, so the
above limitation or exclusion may not apply to you. This warranty
gives you specific legal rights, and you may also have other rights
that vary from state to state.
RETAIN THIS SECTION FOR YOUR RECORDS
* Lexan is a registered trademark of General Electric.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
To download product manuals or purchase Cannon products from an authorized dealer, please visit our web page at
Johnson Outdoors, Inc. / Cannon Division
121 Power Drive, Mankato, MN 56001
1-800-227-6433
© 2008 Johnson Outdoors, Inc. All rights reserved.
All CANNON Downriggers are covered by US Pat.D-269, 992. Copyright 2006 Johnson Outdoors, Inc. All rights reserved.
Conforms to 89/336/EEC (EMC) under standards EN 55022A, EN 50082-2 since 1996 LN V9677264
WARNING: This product contains chemical(s) known to the state of California to cause cancer and/or reproductive toxicity.
16
Form No. 3397104 Rev C
Download from Www.Somanuals.com. All Manuals Search And Download.
|