VANTAGE-HD
OPERATORS Manual
Issue 1.0.2
28 March 2006 © Calibre UK Ltd
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
Contents
PRODUCT DESCRIPTION................................................................................................................ 1
ii
1.1.
1.2.
1.3.
1.4.
1.5.
1.6.
1.7.
1.8.
1.9.
Product Overview................................................................................................ 1
Packing List......................................................................................................... 1
You Will Need...................................................................................................... 1
Physical Dimensions ........................................................................................... 1
Controlling Your Vantage-HD.............................................................................. 1
Serial Control....................................................................................................... 2
Infrared Control ................................................................................................... 2
Firmware Updates............................................................................................... 2
Rear Panel Connections ..................................................................................... 2
CONNECTING VANTAGE-HD TO THE DISPLAY DEVICE ............................................................. 3
2.1. Correct Installation Order .................................................................................... 3
CONNECTING VANTAGE-HD INPUTS............................................................................................ 9
3.1.
3.2.
Introduction.......................................................................................................... 9
Resetting An Input Channel ............................................................................... 10
FREEING INPUT CHANNELS........................................................................................................... 11
4.1.
4.2.
Freeing a Video Channel..................................................................................... 11
Freeing an Audio Channel................................................................................... 11
SELECTING AN INPUT..................................................................................................................... 12
5.1.
5.2.
5.3.
Via the OSD ........................................................................................................ 12
Via the Front Panel.............................................................................................. 12
Via the Numeric Buttons on the Remote............................................................. 12
ADJUSTING AN INPUT..................................................................................................................... 13
6.1. Introduction.......................................................................................................... 13
PICTURE IN PICTURE...................................................................................................................... 16
7.1. Introduction.......................................................................................................... 16
INFORMATION MENU ...................................................................................................................... 18
8.1. Introduction.......................................................................................................... 18
CONFIGURATION MENU ................................................................................................................. 19
9.1. Introduction.......................................................................................................... 19
OUTPUT MODE DETAILS ................................................................................................................ 21
10.1.
10.2.
Introduction.......................................................................................................... 21
Audio Output Formats ......................................................................................... 22
INPUT SIGNAL DETAILS .................................................................................................................. 23
11.1.
11.2.
11.3.
11.4.
11.5.
11.6.
11.7.
Introduction.......................................................................................................... 23
Video Inputs ........................................................................................................ 23
Component Video Input....................................................................................... 23
SDI Input (optional) ............................................................................................. 23
HDMI Input .......................................................................................................... 23
Computer (SVGA) Inputs .................................................................................... 23
Audio Input Formats............................................................................................ 24
POWER SUPPLY SPECIFICATION.................................................................................................. 25
12.1. Introduction.......................................................................................................... 25
REGULATORY APPROVALS............................................................................................................ 26
13.1. CE and FCC Compliance.................................................................................... 26
ENVIRONMENTAL AND SAFETY..................................................................................................... 27
14.1.
14.2.
14.3.
Operating............................................................................................................. 27
Storage................................................................................................................ 27
Safety Issues....................................................................................................... 27
HDMI CONNECTION ADVICE .......................................................................................................... 28
WARRANTY & SERVICE ADVICE.................................................................................................... 30
Issue 1.0.2
28 March 2006 © Calibre UK Ltd
Page ii
Download from Www.Somanuals.com. All Manuals Search And Download.
PRODUCT DESCRIPTION
1.1.
Product Overview
Vantage-HD is a state of the art digital image processor which provides market leading HD&
SD per-pixel multiple Iow-angle aperture-adjusted motion-adaptive de-interlacing and
automatic film pull-down correction for 3:2, 2:2 and non-standard and broken cadences,
significantly outperforming the capabilities of benchmark competitor products.
Vantage-HD features studio-grade image processing algorithms from Teranex for the very
best scaling, film and video noise reduction, MPEG artifact reduction and automatic audio
time-line correction to maintain lip-sync Vantage-HD is a very flexible video and audio router with
multiple HDMI and analog input channels, digital, analog and optical audio support and optional HD-
SDI compatibility.
Vantage-HD has special algorithms for plasma image enhancements, significantly reducing plasma
noise and improving grayscale reproduction. Image quality on large-screen LCDs are also much
improved by Vantage-HD. For projectors, Vantage-HD features the sharpest most flexible keystone
correction on the market and there is also an image warping option available for complex geometric
correction
1.2.
Packing List
The following items are included with your Vantage-HD, if any items are missing please
contact your distributor.
1. Vantage-HD
2. Power supply
3. Power cord
4. CD containing this manual
5. Remote control + batteries
6. Warranty card
1.3.
You Will Need
The following items will be required but are not supplied with your Vantage-HD
1. A suitable display device - see section 17 for details of the output modes supported by
Vantage-HD
2. Cable to connect to your display device
3. A signal source - see section 11 for details of the supported inputs
4. Cable to connect to your signal source
5. Audio processor and cable (required if not using HDMI to connect to the display device).
1.4.
1.5.
Physical Dimensions
The Vantage-HD is approximately 16.4" (416mm) by 10" (253mm) by 3.4" (85mm) WxDxH
NOTE dimensions are excluding optional rack mounting kit.
An optional 19" by 2U rack mounting kit is available. Each bracket is attached by 2x 10-32
1/2" long pan head screws.
Controlling Your Vantage-HD
Setting up and controlling your Vantage-HD is achieved by a simple to use On Screen
Display (OSD), moving around the OSD can be achieved by using the navi-keys on the front
of the Vantage-HD or by using the remote control
Batteries are not installed when the unit ships to maximise their life.
PLEASE ENSURE THAT THE BATTERIES ARE INSERTED IN THE WAY SHOWN
WITHIN THE BATTERY COMPARTMENT OF THE REMOTE CONTROL.
WHEN BATTERIES BECOME DISCHARGED PLEASE REMOVE THEM IMMEDIATELY
AND DISPOSE OF THE IN ACCORDANCE WITH THE INSTRUCTIONS SUPPLIED BY
THE BATTERY MANUFACTURER
Issue 1.0.2
28 March 2006 © Calibre UK Ltd
Page 1 of 30
Download from Www.Somanuals.com. All Manuals Search And Download.
IF THE REMOTE CONTROL IS TO BE LEFT UNUSED FOR AN EXTENDED PERIOD OF
TIME PLEASE REMOVE THE BATTERIES TO PREVENT POSSIBLE DAMAGE CAUSED
BY LEAKING
1.6.
Serial Control
Vantage-HD has a serial port which allows for the unit to be controlled via an integrated
home control system. The connector on Vantage-HD is a 9 way D-Type (female).
Pin 2 = Tx Pin 3 = Rx Pin 5 = Ground
The type of cable required will depend on your home control system but typically a 9 way
Male to 9 way Female connected straight through will allow serial control.
serial control may require the application of a firmware upgrade to your unit via its USB port.
1.7.
1.8.
Infrared Control
The infrared control codes can be downloaded from www.calibreuk.com
Firmware Updates
Calibre operates a policy of continued product improvement as a result we may periodically
issue firmware updates, these are downloaded to the Vantage-HD via the USB port.
Full details of the updates and how to download them are available on our website
1.9.
Rear Panel Connections
The following inputs are located on the rear panel of the Vantage-HD
1. Composite video via RCA jack (2x)
2. S-Video via 4 way mini DIN socket (2x)
3. Component video with or without separate sync via 3/4 RCA jack (2 sets)
4. HDMI version 1.1 (2x)
5. Expansion slot for input expander cards - takes HDMI card or HD-SDI card
6. Computer (SVGA) via 15 way HDD
7. Analog audio stereo pairs via RCA jack (4 sets)
8. S/PDIF coaxial audio (2x)
9. S/PDIF optical audio (2x)
10. Power jack
The following outputs are located on the rear panel of Vantage-HD
1. Analog video output via 15 way HDD (1x)
2. HDMI version 1.1 (1x)
3. Analog audio stereo pair via RCA jack (1 set)
4. S/PDIF coaxial audio (1x)
5. S/PDIF optical audio (1x)
Figure 1 below details the connections to Vantage-HD.
Figure 1 Rear Panel Connections
Issue 1.0.2
28 March 2006 © Calibre UK Ltd
Page 2 of 30
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING VANTAGE-HD TO THE DISPLAY DEVICE
Correct Installation Order
2.1.
The flow chart below details the correct order in which to install your Vantage-HD, following
this order will ensure trouble free installation.
Issue 1.0.2
28 March 2006 © Calibre UK Ltd
Page 3 of 30
Download from Www.Somanuals.com. All Manuals Search And Download.
Connect Vantage-HD SVGA (RGBHV) output or HDMI output to your
display device. If connecting a DVI display device you need to use an
HDMI to DVI converter which we recommend you locate at the display
end of the cable.
Connect to
display device
1.
2.
Connect Vantage-HD audio Coaxial, Optical or Analog output to audio
processor, if HDMI audio output is not being used.
Note: For best audio performance it is recommended that Coaxial or
Optical audio be used, not HDMI audio. Some HDMI sources do not
correctly comply with HDMI specifications which can cause audio
distortion or loss of audio. If this is experienced, please change to using
Coaxial or Optical audio, or consult the supplier of that HDMI source
device.
Connect audio
output
3. Connect input
Connect input video and audio signals to Vantage-HD.
Connect power supply provided with Vantage-HD to Vantage-HD power
inlet jack.
THIS POWER SUPPLY CARRIES A LABEL SHOWING THAT ITS DC
OUTPUT IS 5V at 7A. DO NOT CONNECT ANY OTHER POWER
SUPPLY TO VANTAGE-HD WHICH WILL NOT BE COVERED UNDER
YOUR PRODUCT WARRANTY
Connect Power
4.
Connect the Vantage-HD PSU to your mains outlet and turn on the mains
outlet if it is switched
Configure the
display device
Turn on your display device and select the input channel to which you
have connected Vantage-HD
5.
6.
Switch on
Vantage-HD
Turn on Vantage-HD by pressing the Power (bottom right) button on the
front panel, or by pressing the On button on the remote control.
A new Vantage-HD unit will power up in 640x480 @ 60Hz output mode
since this should be compatible with all common display devices. If your
Vantage-HD has previously been connected it may power up in a
different mode. If this mode is not compatible with your display you can
easily revert to the 640x480 @ 60Hz output mode by simultaneously
pressing the front panel Input key and OK key (OK is the center key of
the 5-button navi-key).
Set Vantage- HD
output mode
7.
Press the Menu key to bring up the OSD menu. Scroll to the Output
Settings menu using the top/bottom navi-keys. Go into that menu by
pressing the right navi-key.
First choose your type of display by using the up/down navi-keys to scroll
to the Display menu item (if not already highlighted) and pressing OK (the
center button of the navi-key). The options which appear are:
a)
b)
c)
LCD - for direct-view LCD displays
Plasma - for plasma displays
Select display
device type
8.
Projector - for solid-state (digital) projectors such as DLP,
LCD, LCOS, DILA or any other type of digital projector
Choosing the appropriate type of display is important since menu items
such as temporal noise reduction and how the OSD is generated are pre-
set to different default values depending on the display type and different
menu items appear or are hidden such as keystone correction.
Issue 1.0.2
28 March 2006 © Calibre UK Ltd
Page 4 of 30
Download from Www.Somanuals.com. All Manuals Search And Download.
Picture 1 Select Display Device Type
Choose the correct display resolution by scrolling down to the Resolution menu
item and pressing OK to display the list of available modes. Note the scroll bar at
the left of the list - it is too long to display the full list on screen so you must
scroll up and down it to see all modes.
For best performance it is critical that you select a mode which is equal to
the native resolution of the display device you are using, provided that the
display supports its native mode. This is to ensure that the internal
scaling within your display device is not operating.
Select display
device
resolution
9
Depending on the mode you choose, Vantage-HD may have to re-boot to
change resolution. If this occurs you need to re-enter the Output menu by
pressing Menu, scrolling to Output Menu with the up/down keys and
entering the Output Menu with the right key
Issue 1.0.2
28 March 2006 © Calibre UK Ltd
Page 5 of 30
Download from Www.Somanuals.com. All Manuals Search And Download.
Picture 2 Select Display Device Resolution
Select the Frame Rate option on the menu. This determines whether the output
of Vantage-HD remains at a constant 59.94Hz, constant 50Hz, or automatically
switches between the two depending on the type of incoming signal being
displayed
Auto mode gives best motion performance in a viewing scenario where you are
looking at content which may be 59.94Hz or 50Hz (North America and anywhere
using the NTSC system usually runs at 59.94Hz, Europe and anywhere using
PAL or SECAM usually runs at 50Hz; there are exceptions though in both
cases.) However when Auto mode is selected there may be display glitches or
display re-sync delays when switching between inputs or when the input signal is
lost - this is due to output frame rate changes affecting the operation of your
display device. Additionally, some HDMI display devices will not operate
correctly in Auto mode due to limitations inherent within those displays.
Select Output
Frame Rate
10
If you are only using 59.94Hz sources, or only using 50Hz sources, it is strongly
recommended you select fixed 59.94Hz or 50Hz respectively so as to improve
the input switching characteristics.
Selecting 50Hz output mode with 59.94Hz input material, or vice versa, causes
frame rate conversion to occur. This can cause slight degradation in motion
performance so is not recommended, but can be used for display devices which
are not compatible with the incoming field rate.
Note: 60Hz display devices should correctly display 59.94Hz modes.
Image Projection - allows correction for the orientation and location of the
projector relative to the screen. Press OK to show list then scroll up/down list
with up/navi-keys, press OK to choose the correct mode. Options are:
a) Front Table - projector is in front of screen and correct way up
b) Front Ceiling - projector is in front of screen but upside down
Image
Projection
11
c)
Rear Table - projector is behind screen but right way up
d) Rear Ceiling - projector is behind screen and upside down
Issue 1.0.2
28 March 2006 © Calibre UK Ltd
Page 6 of 30
Download from Www.Somanuals.com. All Manuals Search And Download.
When connecting your display via the SVGA (RGBHV) connector it is imperative
that the pixel clock and phase settings are correctly adjusted on the menu
system of your display device. For information on how to access these features
see the user manual supplied with your display device. Note: You must set
Vantage-HD to the native resolution of your display device BEFORE adjusting
the pixel clock and phase settings on your display.
To set the pixel clock, with no input displayed on Vantage-HD but with the OSD
present and the blue background shown, adjust the pixel clock setting (on your
display device, not on Vantage-HD) to remove all vertical noise bands from the
blue background. Correct adjustment will cause the vertical bands to move
further apart and reduce in number until they eventually disappear. Many good
displays will automatically select the correct pixel clock setting, but some will not.
IMPORTANT: See Chapter 10 - Output Mode Details for detailed information on
output mode timings including information on the correct pixel clock setting - the
total number of pixel clocks per line. See also Note (b) below when using
1366x768/1360x768 modes.
Optimize Display
Device Setup
12
To set the pixel phase, first set the pixel clock correctly (see above) and
then adjust the pixel phase to remove all horizontal jitter and noise from
the background and the OSD, in particular you should adjust for best
sharpness of the OSD text and graphics.
PIXEL CLOCK AND PHASE ADJUSTMENTS WITHIN THE DISPLAY
DEVICE ARE NOT APPLICABLE WHEN USING A DVI OR HDMI DISPLAY
DEVICE.
Notes: a) Some 1024x1024 plasmas do not correctly support 1024x1024 native
resolution, in this case you must unfortunately select 1024x768 or 1280x768,
experiment to see which gives best performance.
b) There are two 1366x768 modes and a 1360x768 mode provided. This is
because some types of plasma and LCD with this resolution need
different signal timings compared with those which are considered
standard for this format. As a general rule, 1366x768 modes will give
better performance than 1360x768 but some displays do not support
1366x768 modes. The key difference between the two 1366x768 modes
is the length of line blanking. Pick the 1366x768 mode which allows you
to correctly set the pixel clock on your display device and which does not
cause bad clamping. (If the picture appears very dark or very bright then
it is incorrectly clamped due to the selected mode not being compatible
with your display - try the other 1366x768 mode or the 1360x768 mode
instead).
c) 852x480 mode may need to be used for plasma screens with resolutions
of 852 or 853 pixels. Many 853 pixel plasma displays do not actually
support incoming modes with an odd number of input pixels.
d) Never pick a mode with more display lines than the native format of your
display device, selecting a higher resolution mode will not increase the
system performance, it will instead degrade the picture significantly since
it will cause the internal scaler within your display to downsize the picture
resulting in loss of detail and artifacts.
Depending on the frame rate mode you choose, Vantage-HD may have to re-
boot to change resolution. If this occurs you need to re-enter the Output menu
by pressing Menu, scrolling to Output Menu with the up/down keys and entering
the Output Menu with the right key.
Issue 1.0.2
28 March 2006 © Calibre UK Ltd
Page 7 of 30
Download from Www.Somanuals.com. All Manuals Search And Download.
Warp Correction - only applicable if the chosen display type is Projector.
This allows for correction of vertical and horizontal keystone errors
caused by misalignment of the projector to the screen. Correction up to
+/- 30 degrees vertically and +/-40 degrees horizontally are possible,
within the constraints of the chosen native resolution which is dependent
on the display device - a higher resolution display device will give better
results at more extreme angles of adjustment.
Select the Warp Correction menu item using the OK key, then choose
which corner to manipulate, then use the up/down and left/right navi-keys
to manipulate the image by changing the angle of adjustment in the
vertical and horizontal planes respectively.
13 Warp Correction
Note: Although Vantage-HD's Warp Correction allows for extreme off-
angle picture geometry correction and maintains display resolution to the
very best possible level even in such situations, Vantage-HD cannot
correct for mis-focussing of the projector lens. Depending on the
physical and optical characteristics of the optics within your projector,
focus errors may occur at extreme projection angles which may cause
one side of the image to appear less sharp than the other. After setting
warp on Vantage-HD you should adjust the focus of your projector lens to
obtain best overall picture sharpness, paying particular attention to
sharpness in the center of your screen for viewing movies and TV.
Scroll to Output Gamma Mode and choose the gamma mode you require.
This should be left set to Linear unless you also choose the correct input
gamma for every input signal you connect. It is used to map an incoming
gamma curve to a different outgoing gamma curve
Gamma
14
Correction
Audio Delay - the audio delay through Vantage-HD is automatically set to
compensate for the delay through Vantage-HD which is typically 5-7
fields.
The Audio Delay option on the Output Menu does not override this
automatic setting but allows fine calibration of the audio delay in steps of
approximately 1 mS, to advance or retard the audio so as to compensate
for further delays in your display device or your audio system. If you notice
lipsync errors when viewing program material, you can use this option to
reduce or remove that error. Fine tuning of the audio delay can only be set
correctly when viewing real program material so should not be adjusted at
this stage
Setting Audio
15
Delay Mode
Output configuration is now complete, apart from fine-tuning the audio delay, which may
require adjustment later, depending on your display device and audio system. Exit the
Output Menu by pressing the left navi-key.
Issue 1.0.2
28 March 2006 © Calibre UK Ltd
Page 8 of 30
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING VANTAGE-HD INPUTS
3.1.
Introduction
It is now necessary to define which input channels are connected and to pair the correct
audio channel with each video channel. To begin to do this, scroll down to the Input
Connections menu and enter that menu by pressing the right navi-key.
By default, no video channels and no audio channels are active. You must define which
channels are connected on the Input Connections menu and choose whether or not each
video channel has an associated audio channel. Only those video channels which are
physically present on your Vantage-HD are shown, those which are grayed-out require an
additional expansion module.
NOTE
If your input device allows you to select an output resolution please select the native
resolution of the image to be displayed
To enable or disable a video channel, scroll to that channel type with the up/
down navi-keys, then press OK. You must then give that channel a name
which means something to you or your installation/system for future
reference. Do this by using the up/down navi-keys to scroll through the
available characters and numbers (fast-scroll through the list automatically
activates after approx 2 seconds). Then use the left/right navi-keys to move
to the next character in the name, or go back to alter a character you have
already chosen. (Note: To delete a character and not replace it with another,
scroll with the up/down navi-keys to select the blank/space character.) It is
not possible to enable a video channel or associate a sound channel with it
until you have named that channel. Press the OK button when you have
finished naming that input, the channel will now automatically be enabled as
an available input.
Naming an
Input
16.
To enable direct-selection of an input channel, using the numeric keys on the
remote control, scroll to the Input Number with the up/down navi-keys, then
press OK. Select the desired number from the list the press OK.
Input Number
(optional
configuration)
Numeric selection is not essential for the operation of Vantage-HD but does
provide a quick method of getting to the desired input.
After naming the input channel, scroll down to the Sound Source menu item
to choose the associated sound channel and press OK to view the list of
available sound channels. If there is no associated sound channel (e.g. for a
PC input with no audio) choose None. Only those sound channels which
have not already been allocated to another video input channel are available
for selection, those which have already been allocated are grayed-out.
17. Associating an
Audio Channel
Note the scroll bar at the left of the list - there are too many audio channels to
display all at once, you must scroll up and down the list to see all the
available channel options.
Note: HDMI audio inputs can only be associated with the matching HDMI
video input. For best audio performance we recommend using Coax or
Optical SPDIF audio where supported by the source.
For analog Component Video inputs only, you can also choose whether the
input source provides YPbPr, YPbPrS, RGB or RGBS video.
18. For Analog
Component Video
Only
It is important to select the correct color and sync format, otherwise the
picture coloration will be wrong or no picture may be displayed. Most North
American DVD players and set-top boxes output YPbPr. Most European
(SCART) devices output RGBS
Issue 1.0.2
28 March 2006 © Calibre UK Ltd
Page 9 of 30
Download from Www.Somanuals.com. All Manuals Search And Download.
Definition of that video input channel is now complete
You should now repeat steps 16 to 18 to the define all the remaining video and audio
channels you wish to use. When you have finished defining input channels, exit the Input
Connections menu using the left navi-key to move back to the main menu on the left of the
OSD
3.2.
Resetting An Input Channel
This very useful function resets all the input parameters to the default
settings for that input channel with the current selected display device
type. This enables you to recover to known settings
Reset Channel
Input Setup Menu
Issue 1.0.2
28 March 2006 © Calibre UK Ltd
Page 10 of 30
Download from Www.Somanuals.com. All Manuals Search And Download.
FREEING INPUT CHANNELS
4.1.
Freeing a Video Channel
Should you wish to disable a video input, you may do so by re-selecting that video channel
from the Input Connections menu, selecting the Disable Channel function and then selecting
Yes from the warning message which appears. Disabling a video input channel not only
removes it from the input selections list, it also erases its name and de-allocates its
associated audio channel.
Note: If all possible input channels are disabled, the OSD will exit at the point at which the
last channel is disabled. This is because there are now no valid inputs so Vantage-HD has
switched to its unconfigured (default) mode of operation. In this default mode the input
channel to be displayed is undefined so may vary randomly. To start re-defining the input
channels, press the Menu button again and use the navi-keys to re-enter the Input
Connections menu.
4.2.
Freeing an Audio Channel
Should you need to free up a previously allocated channel, go to that video input channel
and select a different audio channel or no audio channel for association with that video input
channel.
Press OK when you have chosen the correct audio channel.
Note: HDMI inputs by default associate themselves with the HDMI audio on that HDMI video
channel. You can change this to any available digital or analog audio input if you wish, but
cannot cross-select audio from a different HDMI video channel, e.g. HDMI2 can use audio
from HDMI2 or from any analog or digital audio input, but HDMI2 video cannot be
associated with audio from HDMI1 input. Calibre recommends use of Coaxial or Optical
digital audio where the source device allows.
Issue 1.0.2
28 March 2006 © Calibre UK Ltd
Page 11 of 30
Download from Www.Somanuals.com. All Manuals Search And Download.
SELECTING AN INPUT
5.1.
Via the OSD
Now you can choose from the input channels you have defined by scrolling up to the Input
Selection menu. Here you will find listed those input channels you have defined. Press the
right navi-key to enter the Input Selection menu, then scroll to the input you wish to view or
whose configuration you wish to alter. Press OK to select it.
5.2.
5.3.
Via the Front Panel
Alternatively you can step through the defined input channels when the OSD is not displayed
by using the Input key on the front panel of Vantage-HD.
Via the Numeric Buttons on the Remote
You can also direct-select an input channel by its number in the Input Selection listing, using
the numeric keys on the remote control.
It is also possible to change the allocated numbers for those input channels in the Input
Selection list. To do this scroll to that channel type with the up/down navi-keys, then press
OK. Scroll to the Input Number, then press OK. Select an alternative number from the list.
Note the order of the list does not change on the OSD.
Input Selection Menu
Issue 1.0.2
28 March 2006 © Calibre UK Ltd
Page 12 of 30
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUSTING AN INPUT
6.1.
Introduction
When an input channel has been selected, an input type dependent Picture Controls menu
can be accessed. Note that for this menu to be fully accessible, a valid video input signal
MUST be connected to the chosen video input channel. All settings on the Picture Controls
menu are stored separately for each input channel and so do not affect the other inputs.
Note: Default settings for many items are dependent on the type of input channel and the
type of display device chosen.
To adjust the picture settings, scroll to the Picture Controls menu then press the right navi.
key to enter that menu.
MANY SETTINGS ARE SIGNAL-TYPE DEPENDENT. NOT ALL ADJUSTMENTS ARE
PRESENT FOR EVERY INPUT SIGNAL TYPE, THE LIST BELOW SHOWS ALL
POSSIBLE OPTIONS BUT THESE ARE NEVER ALL AVAILABLE SIMULTANEOUSLY
SINCE SOME ARE EXCLUSIVE TO ONE INPUT TYPE, SOME ARE EXCLUSIVE TO
ANOTHER INPUT TYPE. BE SURE TO HAVE THE CORRECT INPUT SOURCE
CONNECTED AND RUNNING, OTHERWISE THE CONTROLS MAY NOT HAVE THE
DESIRED EFFECT WHEN THE ACTUAL SIGNAL IS CONNECTED.
Brightness
Contrast
Control of background level
Control of video gain
Control of the sharpening enhancement filters' levels. (video input
signals only)
Sharpness
Color
Saturation and Hue controls on a sub menu (video input signals only)
A submenu allowing adjustment of the pixel clock (total number of pixel
clocks per line) and the pixel phase for the SVGA (RGBHV) input only.
This menu item only appears with the SVGA input selected.
Pixel Clock & Phase
Automatically adjusts the pixel clock and phase settings for the SVGA
input. This menu item only appears with the SVGA input selected.
Auto Setup
Picture Format
Contrast Enhance
Aspect Ratio control list for selection of correct format
Preconfigured contrast enhancements which can be selected to suit your
personal requirements and the material being viewed.
Picture Controls Menu
Issue 1.0.2
28 March 2006 © Calibre UK Ltd
Page 13 of 30
Download from Www.Somanuals.com. All Manuals Search And Download.
A submenu containing selection options for many image enhancement
filters including
Video Filters
(Video input
signals only)
CCS Cross Chrominance Suppression filter (reduction of chroma-crawl)
CUE Chroma Upsampling Error correction filter
ICP
Interlace Chroma Problem filter - Reduces chroma interlace errors on
diagonals and curves
TNR Temporal Noise Reduction (removes "electronic" noise found on
broadcasts, film material and particularly noticeable on plasma
screens; set to High to significantly improve signal to noise ratio on
plasmas)
MPEG
Select whether MPEG spider and block noise is on or off and adjusts
the level of MPEG noise reduction for SD signals. Not applicable to
HD formats – use TNR for removal of all types of noise from HD
formats.
Video Filters Menu
Issue 1.0.2
28 March 2006 © Calibre UK Ltd
Page 14 of 30
Download from Www.Somanuals.com. All Manuals Search And Download.
Picture Settings
A submenu of picture control functions including
Color temperature
To select the color temperature of the incoming material. Options are
Warm, Neutral, cold. With a 7200K display device (a typical projector
or LCD set to neutral) these correspond to nominal settings of
6500K, 7200K & 9300K respectively. For neutral color temperature
response, that is, to leave the response of the program material
unmodified, select Neutral, this is the default setting
Input gamma mode
Used to re-map an input gamma to a different output gamma setting.
Only use this function if the output gamma has also been chosen on
the Output Settings menu, otherwise leave set to Linear
Black Level
Use to select or de-select 7.5IRE black level set-up adjustment.
Should always be on for HDMI video inputs and should usually be off
for analog video inputs.
Input Capture
Select the amount of overscan.
Position
Allows horizontal and vertical adjustment (pan and tilt) of the
captured active image area within the overall display resolution.
Note: The range of position adjustment available is limited by the
characteristics of the signal timings from the image source
equipment: in some circumstances adjustment may not be possible,
particularly with HDMI/DVI signals. Significant changes in output
image position (to correct for projector alignment errors) should be
effected via the Warp corner-adjustment menu.
Size
Allows control of the width and height of the image, used to fine-tune
the aspect ratio or to adjust to a nonstandard aspect ratio. Can also
be used to select an adjustable amount of horizontal and vertical
overscan or underscan.
Picture Settings Menu
Issue 1.0.2
28 March 2006 © Calibre UK Ltd
Page 15 of 30
Download from Www.Somanuals.com. All Manuals Search And Download.
PICTURE IN PICTURE
7.1.
Introduction
To enable PIP mode, scroll down the main menu to the Picture-in-Picture Settings menu
and press the right navi-key to enter that menu. To enable PIP, scroll to the PIP Enable
option and press the OK key. Note: You cannot use the PIP menu successfully without at
least two active inputs connected to Vantage-HD.
Use the PIP Inputs menu to select which picture is displayed in the
PIP window
Selecting the input
Swapping PIP
Use the PIP Swap function to swap the primary image with the PIP
image
Use the PIP Position function to chose the location of the PIP
image from
Top Left
Positioning the PIP
OSD not visible
Top Right
Bottom Left
Bottom Right
When the PIP is displayed and the OSD menu is not on screen
the navi-key arrows can be used to move the PIP around the
screen and re-size the PIP window
PIP Limitations - due to the high demands on the processing
power available within the Realta HQV chip when a HD main
image is displayed, full Teranex Video Processing is not always
available when PIP is in use.
If the main image is 1080i or 1080p and the PIP image is 720p,
1080i or 1080p the maximum available image processing
bandwidth may be exceeded. In such circumstances Teranex
Video Processing is automatically disabled resulting in reduced
image quality. Full image processing performance and quality is
automatically restored when the PIP is closed.
Limitations
If the main image or the PIP image are SD then full Teranex Video
Processing is maintained even with a PIP showing.
Issue 1.0.2
28 March 2006 © Calibre UK Ltd
Page 16 of 30
Download from Www.Somanuals.com. All Manuals Search And Download.
Picture In Picture Menu
Issue 1.0.2
28 March 2006 © Calibre UK Ltd
Page 17 of 30
Download from Www.Somanuals.com. All Manuals Search And Download.
INFORMATION MENU
8.1.
Introduction
The Information Menu provides information about the version and status of your Vantage-
HD. Information shown is
Vantage revision
Vantage-HD Information
the version number of the control software and user menu/user
controls functionality in your Vantage-HD.
Displays details of the physical the video and audio connection
channel presently selected
Input Source
Input Format
Displays approximate details of the detected input video signal
including vertical frequency (refresh rate), horizontal frequency (line
rate) and resolution. Note that if the input is interlaced, the de-
interlaced resolution is shown
Displays approximate details of the output video signal including
vertical frequency (refresh rate), horizontal frequency (line rate) and
resolution
Output Format
Important Note: The input and output format measurements are approximate only and do
not show the exact precise refresh and line rate; they are subject to tolerances due to the
measurement method and calculation rounding. Do not be alarmed if the input rate or output
rate is not exactly what you think it ought to be.
Information Menu
Issue 1.0.2
28 March 2006 © Calibre UK Ltd
Page 18 of 30
Download from Www.Somanuals.com. All Manuals Search And Download.
CONFIGURATION MENU
9.1.
Introduction
The Configuration Menu allows the user to customize the "look and feel" of the Vantage-HD user
interface
Language
Allows selection of the language for the OSD, current options are
English (American) - default
English (British)
Francais
Deutsch
Menu Colors
Allows selection of the color scheme for the OSD, options are
Blue - default
Gray
Green
Transparent Menu
Allows the displayed image to be viewed through the OSD menu by
making the OSD semi-transparent. Default is off
3-D Effect
Changes the menu borders between flat (default) and 3-D effect
Allows the HDMI operation mode to be changed between Repeater
and Receiver.
HDMI Audio Input
When configured as a Repeater, the HDMI capabilities of your
attached display device are relayed through Vantage-HD to your
HDMI source equipment.
When configured as a Receiver, the HDMI capabilities seen by your
source equipment are fixed by Vantage-HD and do not relate directly
to the capabilities of your attached display device.
If using audio from the HDMI output of Vantage-HD together with
HDMI audio from your source equipment, you should always select
Repeater, otherwise the audio signal presented to your display device
may not be compatible with it.
If using HDMI audio inputs to Vantage-HD from your source
equipment, but using the Coaxial or Optical audio outputs from
Vantage-HD, you should always select Receiver, otherwise multi-
channel audio may not be available from the Coaxial or Optical audio
outputs.
If you find that the HDMI behavior of your source or display
equipment is erratic or not as expected, try changing the HDMI mode
since some display devices and some source equipment do not
correctly support Repeater mode.
IMPORTANT:
i) Before changing from Receiver to Repeater mode, make sure your
display device is connected and turned on.
ii) Before changing from Receiver to Repeater, or from Repeater to
Receiver, we recommend that you disconnect or power down any
connected HDMI source equipment.
Note: Use of analog audio outputs with HDMI audio inputs is not
Issue 1.0.2
28 March 2006 © Calibre UK Ltd
Page 19 of 30
Download from Www.Somanuals.com. All Manuals Search And Download.
recommended since in many instances analog audio out will be
automatically disabled due to HDCP and HDMI licensing
requirements.
0SD Timeout
The time between the last keypress and the OSD being automatically
removed.
Note: The default setting of 0 means no timeout, the OSD remains
until it is removed by pressing a the Menu key
Infoscreen Timeout
Factory Reset
The time between pressing the info key (or a channel change) and
the infoscreen being automatically removed
Note: The default setting of 0 means no timeout, the OSD remains
until it is removed by pressing a the Menu key
This performs a global reset of all parameters within Vantage-HD, all
settings are returned to their factory default settings. This function
should only be used as a last resort, you will lose absolutely all your
previous configuration settings
Issue 1.0.2
28 March 2006 © Calibre UK Ltd
Page 20 of 30
Download from Www.Somanuals.com. All Manuals Search And Download.
OUTPUT MODE DETAILS
10.1.
Introduction
The following output modes are supported by Vantage-HD
Resolution
H Freq
31.469
26.25
V Freq
59.94
50
H act
H Tot
HS
96
96
HBP
V act
480
V Tot
525
VS VBP
640×480
640×480
640
800
48
2
2
33
33
640
800
48
480
525
800×600
800×600
37.642
31.4
59.94
50
800
800
1056
1056
1044
1044
1044
1044
1344
1312
1408
1408
1650
1980
1664
1664
1688
1688
1792
128
128
24
88
88
600
600
480
480
480
480
768
768
1024
1024
720
720
768
768
1024
1024
768
628
628
525
525
525
525
806
793
1056
1056
750
750
798
798
1066
1066
795
4
4
4
4
4
4
6
4
3
3
5
5
7
7
3
3
3
23
23
30
30
30
30
29
18
26
26
20
20
20
20
38
38
20
852×480
26.25
31.469
26.25
31.469
48.312
39.65
52.8
50
852
48
852×480
59.94
50
852
24
48
853×480
852
24
48
853×480
59.94
59.94
50
852
24
48
1024×768
1024×768
1024x1024
1024x1024
1280×720
1280×720
1280×768
1280×768
1280×1024
1280×1024
1360×768
1024
1024
1024
1024
1280
1280
1280
1280
1280
1280
1360
136
104
160
160
40
160
144
203
203
260
220
192
192
248
248
300
50
63.297
44.955
37.5
59.94
59.94
50
40
47.83
39.9
59.94
50
128
128
112
112
100
63.896
53.3
59.94
50
39.75
50
1360×768
1366x768-1
1366x768-1
47.652
38.75
59.94
50
1360
1366
1366
1792
1450
1450
100
30
300
50
768
768
768
795
775
775
3
3
3
20
3
46.454
59.94
30
50
3
1366x768-2
1366x768-2
1400×1050
1400×1050
1920×1080
1920×1080
1400x788
39.75
47.652
53.3
50
59.94
50
1366
1366
1400
1400
1920
1920
1400
1400
1792
1792
1688
1688
2640
2200
1850
1850
100
100
112
112
44
300
300
128
128
192
148
300
300
768
768
795
795
3
3
3
3
5
5
3
3
20
20
12
12
38
36
18
18
1050
1050
1080
1080
788
1066
1066
1125
1125
815
63.896
56.25
67.433
40.75
48.851
59.94
50
59.94
50
88
100
100
1400x788
59.94
788
815
1920x1200
1920x1200
61.75
50
1920
1920
2080
2080
32
32
80
80
1200
1200
1235
1235
6
6
26
26
74.026
59.94
Issue 1.0.2
28 March 2006 © Calibre UK Ltd
Page 21 of 30
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes:
a)
Some 1024x1024 plasmas do not correctly support 1024x1024 native resolution, in
this case you must unfortunately select 1024x768 or 1280x768, experiment to see
which gives best performance.
b)
There are two 1366x768 modes and a 1360x768 mode provided. This is because
some types of plasma and LCD with this resolution need different signal timings
compared with those which are considered standard for this format. As a general rule,
1366x768 modes will give better performance than 1360x768 but some displays do
not support 1366x768 modes. The key difference between the two 1366x768 modes is
the length of line blanking. Pick the 1366x768 mode which allows you to correctly set
the pixel clock on your display device and which does not cause bad clamping. (If the
picture appears very dark or very bright then it is incorrectly clamped due to the
selected mode not being compatible with your display - try the other 1366x768 mode
or the 1360x768 mode instead).
c)
852x480 mode may need to be used for plasma screens with resolutions of 852 or 853
pixels. Many 853 pixel plasma displays do not actually support incoming modes with
an odd number of input pixels.
e) Never pick a mode with more display lines than the native format of your display
device, selecting a higher resolution mode will not increase the system performance, it
will instead degrade the picture significantly since it will cause the internal scaler within
your display to downsize the picture resulting in loss of detail and artifacts
10.2.
Audio Output Formats
One analog stereo pair via RCA jack connectors, output format 1V pk-pk nominal 1K output
impedance
1 S/PDIF coaxial with up to 8 audio channels
1 S/PDIF optical with up to 8 audio channels
NOTE
Vantage-HD does not downmix audio inputs, so if 5.1 or 7.1 audio is input, the 2 channel
analog audio outputs may not produce acceptable sound quality. Use of analog audio
outputs with HDMI audio inputs is not recommended since in many instances analog audio
out will be automatically disabled due to HDCP and HDMI licensing requirements.
Issue 1.0.2
28 March 2006 © Calibre UK Ltd
Page 22 of 30
Download from Www.Somanuals.com. All Manuals Search And Download.
INPUT SIGNAL DETAILS
11.1.
11.2.
Introduction
This section provides technical details for all possible inputs please refer to the model
specification to determine which inputs can be displayed by your Vantage-HD.
Video Inputs
Composite via RCA jacks
S-Video via 4-way mini DIN socket
Signal formats
Composite (CVBS), S-Video (Y/C), Standards
NTSC, PAL, SECAM
Composite (CVBS) input level
Luminance (Y) input level
Chrominance (C) input level
Input Impedance (all inputs)
Component Video Input
Via 3 or 5 RCA jacks
1V p-p nominal inc. sync
1V p-p nominal inc. sync
0.6V p-p nominal
75 Ohms
11.3.
YPbPr, YPbPrS, RGB and RGB(S) component video
Signal formats 484i and 576i (SD), 480p, 576p (ED), 720p, 1080i at 50, 59.94 and 60Hz
and 1080p at 24, 25 and 30Hz.
Please note this input does not support Computer SVGA signals which should be
connected via the Computer SVGA input
11.4.
11.5.
SDI Input (optional)
Format:
SD-SDI and HD-SDI YCbCr 4:2:2 serial digital component video
Input impedance: 75 ohms.
SMPTE 292M and SMPTE 259M-C compliant
HDMI Input
HDMI format 1.1 with HDCP
Signal formats
484i and 576i (SD), 480p, 576p (ED), 720p, 1080i at 50, 59.94 and 60Hz and 1080p at
24, 25 and 30Hz
1080p at 50 and 60Hz
11.6.
Computer (SVGA) Inputs
Signal formats:
DOS
VGA
SVGA
XGA
WXGA
SXGA
720 x 400
640 x 480
800 x 600
1024 x 768
1280 x 768
1280 x 1024
70Hz
60Hz to 75Hz inclusive
56Hz to 75Hz inclusive
60Hz to 75Hz inclusive
60Hz to 75Hz inclusive
60Hz
RGB video level
RGB input impedance
Sync formats
0.7V - 1.0V
75 Ohms
1.
Separate H & V sync at TTL levels.
Issue 1.0.2
28 March 2006 © Calibre UK Ltd
Page 23 of 30
Download from Www.Somanuals.com. All Manuals Search And Download.
11.7.
Audio Input Formats
Four analog stereo pairs via RCA jack connectors, nominal 1V pk-pk 10K input impedance
2 S/PDIF coaxial with up to 8 audio channels
2 S/PDIF optical with up to 8 audio channels
Issue 1.0.2
28 March 2006 © Calibre UK Ltd
Page 24 of 30
Download from Www.Somanuals.com. All Manuals Search And Download.
POWER SUPPLY SPECIFICATION
12.1.
Introduction
Should the mains power supply become damaged or fail please contact your Vantage-HD
distributor for a replacement.
Any replacement power supply should meet or exceed the following specifications
Input voltage
AC Inlet
100V to 240V; AC 50Hz to 60Hz; 1.5A.
Desktop Type with IEC320 C8(2P)
5V DC at 7A
Output voltage
Output connector
2.1 x 5.5 x 12mm female barrel +ve centre polarity.
Operating temperature
Storage temperature
Protection Mode
0°C ~ 40°C
-40°C ~ 85°C
Short Circuit Protection, Over Voltage Protection,
Over Load Protection
Approvals
FCC Class B and CISPR22 Class B. • CE, UL,
cULs, TUV, CB and BSMI approved.
Issue 1.0.2
28 March 2006 © Calibre UK Ltd
Page 25 of 30
Download from Www.Somanuals.com. All Manuals Search And Download.
REGULATORY APPROVALS
13.1.
CE and FCC Compliance
CE:
This product complies with the requirements of 89/336/EEC Electromagnetic Compatibility
Directive amended by 92/31/EEC and 93/68/EEC, and 73/23/EEC Low Voltage Directive.
Compliance is to EN55022 Class B (domestic/commercial use).
FCC:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired
operation.
The user is cautioned that changes and modifications made to the equipment without
approval of the manufacturer could void the user’s authority to operate this equipment. It is
required that the user use only shielded and grounded signal cables to ensure compliance
with FCC rules.
Issue 1.0.2
28 March 2006 © Calibre UK Ltd
Page 26 of 30
Download from Www.Somanuals.com. All Manuals Search And Download.
ENVIRONMENTAL AND SAFETY
14.1.
14.2.
14.3.
Operating
o
o
Temperature
0 C to 40 C (32°F to 104°F)
Humidity (non condensing)
Storage
0% to 95%
o
o
Temperature
-25 C to 85 C (-13°F to 185°F)
Humidity (non condensing)
Safety Issues
0% to 95%
SAFETY WARNING:
1. THERE ARE NO USER SERVICEABLE PARTS WITHIN THE UNIT, THE REMOTE CONTROL OR
THE MAINS POWER SUPPLY. DO NOT REMOVE THE POWER SUPPLY COVER - DANGEROUS
VOLTAGES WILL BE EXPOSED. DO NOT OPERATE VANTAGE-HD WITH ITS COVER REMOVED.
2. ENSURE THAT ALL ELECTRICAL CONNECTIONS (INCLUDING THE POWER CORD AND ANY
EXTENSION LEADS) ARE PROPERLY MADE AND COMPLY WITH ELECTRICAL SAFETY
REGULATIONS APPLICABLE TO YOUR LOCATON.
3. ENSURE THAT THE INTEGRITY OF THE EQUIPMENT ISOLATION BARRIER IS MAINTAINED
WHEN CONNECTING TO OTHER EQUIPMENT. THIS MEANS THAT ONLY LOW VOLTAGE
ISOLATED CIRCUITS MAY BE CONNECTED TO THE SIGNAL INPUTS AND OUTPUTS. IF ANY
DOUBT EXISTS CONSULT QUALIFIED SERVICE PERSONNEL.
4. TO PREVENT SHOCK OR FIRE HAZARD DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR
MOISTURE. IF SUCH EXPOSURE OCCURS, REMOVE THE PLUG FROM THE MAINS OUTLET AND
HAVE THE EXPOSED UNIT CHECKED BY QUALIFIED SERVICE PERSONNEL.
5. VANTAGE-HD IS DESIGNED FOR NORMAL DOMESTIC USE IN A DRY ENVIRONMENT. DO NOT
USE OUTSIDE, OR IN AREAS OF HIGH HUMIDITY SUCH AS IN THE VANCINITY OF KITCHEN
APPLIANCES, IN THE BATHROOM OR SHOWER ROOM, SAUNA, STEAM ROOM, SWIMMING
POOL OR ANY OTHER DAMP ENVIRONMENT. USE IN A DAMP ENVIRONMENT MAY CAUSE
DAMAGE TO VANTAGE-HD AND IS DANGEROUS.
6. DO NOT CONTINUE TO OPERATE THE EQUIPMENT IF YOU HAVE ANY DOUBT ABOUT IT
WORKING NORMALLY, OR IF IT IS DAMAGED IN ANY WAY. WITHDRAW THE MAINS PLUG FROM
THE MAINS OUTLET AND CONSULT QUALIFIED SERVICE PERSONNEL.
7. DO NOT REMOVE ANY FIXED COVERS UNLESS YOU ARE QUALIFIED TO DO SO AND EVEN
THEN WITHDRAW THE MAINS PLUG FROM THE MAINS OUTLET BEFORE YOU START.
8. THE COVER OF VANTAGE-HD SHOULD ONLY BE REMOVED FOR INSTALLATION OF UPGRADE
BOARDS AND EVEN THEN ONLY ONCE DISCONNECTED FROM THE POWER SUPPLY AND ALL
ASSOCIATED EQUIPMENT. DO NOT ATTEMPT TO INSTALL AN UPGRADE BOARD UNLESS YOU
ARE CONFIDENT OF YOUR ABILITY TO DO SO AND YOU ARE WEARING A GROUNDED ANTI-
STATIC WRISTBAND. DAMAGE CAUSED DURING UPGRADES OR WITH THE COVER REMOVED
IS NOT COVERED UNDER THE LIMITED WARRANTY.
9. TO AVOID DANGER OF EXPLOSION, DO NOT OPERATE THIS EQUIPMENT IN AN EXPLOSIVE
ATMOSPHERE
Issue 1.0.2
28 March 2006 © Calibre UK Ltd
Page 27 of 30
Download from Www.Somanuals.com. All Manuals Search And Download.
HDMI CONNECTION ADVICE
Vantage-HD has two HDMI input ports and one HDMI output fitted as standard. Two further HDMI
inputs can be fitted by installing an optional expansion module.
HDMI is essential for the connection of HDMI-only HDTV sources with HDCP encrypted video and
audio, such as HD-DVD, Blu-Ray and some HD Satellite/Cable services, however for SD applications
Calibre advises you read and carefully consider the information below to help you decide whether you
will get better performance in your own install by using component video or using HDMI.
HDMI was intended to be a universally compatible standard where all manufacturers' equipment would
seamlessly inter-operate. Unfortunately this is not the case. Due to the huge complexity of implementing the full
HDMI-HDCP protocol and associated software and firmware, there are a wide range of products on the market
which are technically "compliant" but which do not actually inter-operate reliably. This is further exacerbated by
the strictness of the HDMI standard which has led many equipment manufacturers to try to implement work-
arounds so as to ensure those products are actually able to perform the functions which their users need and
demand. This has unfortunately led to even more incompatibility issues. Many later HDMI systems are better, but
there are still many issues with many well-know brands of equipment.
Typically, HDMI compatibility and limitation issues manifest themselves in the following ways:
i) Loss of audio, or corrupted/distorted audio.
ii) Loss of picture and audio or "HDCP patterns" on the screen.
iii) Freezing of the HDMI source or the HDMI display.
iv) Long HDMI-HDCP handshake periods when a new source is selected.
v) Inability to access the native output format of your DVD player through its HDMI output channel.
These are common issues with HDMI equipment which affect may different products in different ways, they do
not particularly relate to Calibre's HDMI implementation but in order to try to ease the effects of (i), (ii) & (iii),
Vantage-HD has been designed with two different HDMI operating modes available for selection via its
Configuration Menu:
Possible modes are:
i) "Repeater” in which the operation mode is set by the HDMI display, whereby Vantage-HD operates as an
HDMI Repeater, relaying audio configuration information from the connected HDMI display back to the HDMI
sources.
This mode should ONLY be used when an HDMI display is being used AND the audio capability of
that HDMI display is also being used. In this mode, the maximum number of audio channels will be
determined by the HDMI display's capabilities.
DO NOT use this mode if you do not have an audio-capable HDMI display connected or if you wish to
connect an audio processor or amplifier to the S/PDIF Coaxial or Optical audio outputs of Vantage-HD.
Incorrect use of this mode can lead to total loss of all HDMI audio from the HDMI inputs, or the
audio may be inadvertently limited to 2 channels when multi-channel audio is desired.
ii) “Receiver” where Vantage-HD’s own capabilities are readable by the HDMI source equipment. In this mode
Vantage-HD appears to the HDMI source equipment to be a display. The capabilities of the HDMI display
device, if connected, are not relayed back to the sources.
This mode should ONLY be used when either (a) the HDMI output is not being used or (b) the HDMI
output is being used for video only and a separate audio output connection has been made
DO NOT use this mode if you wish to use the audio capability of the HDMI output. Incorrect use of
this mode can lead to the HDMI audio output format being incompatible with the connected display,
leading to loss of audio or distorted audio.
Issue 1.0.2
28 March 2006 © Calibre UK Ltd
Page 28 of 30
Download from Www.Somanuals.com. All Manuals Search And Download.
HDCP Handshake delays
HDMI inputs can suffer from delays in locking to a new input source, or a source which has just changed
resolution or format. These delays are handshake delays relate to the inherent HDMI-HDCP handshake period
between your display device and your source equipment. This is unfortunately outside of the control of Vantage-
HD which simply relays HDCP information between display and source, as is mandated by the HDMI-HDCP
licensing rules.
This kind of issue affects switchers as well as processors and is a real nuisance. The only legal
way around it is not to use HDMI which in many cases is undesirable or impractical.
Can Your HDMI Source Output an Unprocessed Signal?
The ability to access your DVD player's native format depends on whether the designer of your DVD
player provided you with the ability to output 480i or 576i from the HDMI output on your player. Unfortunately
most players do not have this ability, although some do exist which can.
Native PAL is 576i and native NTSC is 480/484i, so if you are outputting 576p or 480p then this has already
been de-interlaced by your DVD player. You can check this by looking at the menus to find out if the line rate is
approx 15KHz (i) or approx 31KHz (p).
A common mistake when using Vantage-HD is for the user to allow the DVD player to de-interlace or scale the
signal from its native format. This is very bad for picture quality since the de-interlacing and scaler within
Vantage-HD is far better than that within a DVD player itself.
If the picture content has already been screwed up by the scaler within the DVD player, the improvement seen
when using Vantage-HD is not as great as when Vantage-HD is given a native format signal. Remember, unless
you have a true HD-capable DVD player (a Blu-Ray or HD-DVD player) then your native format is 480i if playing
an NTSC DVD and 576i if playing a PAL DVD. All other formats are NOT native since they differ from the format
in which the DVD itself was recorded.
Unfortunately many HDMI-capable DVD players refuse to output unprocessed "i" formats on their HDMI
connectors, which is very annoying of them since to get best performance you ought to let Vantage-HD do all the
processing, including the de-interlacing. This can be a significant reason for using Component instead of HDMI
since you generally have more control of Component via the menus on your DVD itself.
Which is better, HDMI or Component? Well, you can argue this forever, we all have our own opinions, but what
matters is which works best for you in your own install with your own gear. If you get best picture performance
with HDMI then go ahead and use it, but if you get best performance with Component then use that instead.
We ourselves have tried many DVD from several leading manufacturers, each with varying results in terms of
how "HDMI Compatible" they were. Our Company view is that component video is the preferable connection
medium when using a standard definition source such as a PAL or NTSC DVD player since it is so important to
output from the player at native resolution.
There is also the issue of how many bits HDMI runs at compared with the component video signal. That depends
on the data format which your DVD player chooses to output, but this is something you almost certainly have no
control over; many players choose to output RGB which means that on single-link HDMI they are running at 8-
bits not 10.
This is our view but even so, if you prefer to use HDMI with your SD source, go ahead and do so - that's what we
put the inputs there for!
Please remember, we are not stating that HDMI is useless, or that our HDMI implementation is useless, but we
are observing that some SD-originated sources don't work terribly well on HDMI. This is far less likely to be the
case for true HD sources where use of HDMI is often mandatory. However, these tend to be newer product
designs with better inter-operability. Hopefully this information will allow you to make an informed choice about
which connection method is best for your own system.
Issue 1.0.2
28 March 2006 © Calibre UK Ltd
Page 29 of 30
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY & SERVICE ADVICE
1.
CALIBRE OFFERS A LIMITED PRODUCT WARRANTY FOR 12 MONTHS
FROM DATE OF PURCHASE, SUBJECT TO REGISTRATIONYOU’RE
YOUR
PRODUCT
EITHER
ONLINE
ON
OUR
WEB
SITE
REPAIR OF REPLACEMENT OR DEFECTIVE PARTS AND IN NO CASE
WILL THE LIABILITY EXCEED THE PURCHASE PRICE.
2.
3.
CALIBRE UK LTD ACCEPT NO LIABILITY FOR DAMAGE TO SOURCE
EQUIPMENT, DISPLAY DEVICE OR AUDIO PROCESSOR DUE TO
INCORRECT INSTALLATION, MISUSE OR ABUSE, OR OCCURRENCES
OUTSIDE OF CALIBRE UK LTD’S REASONABLE CONTROL.
ALL SERVICE TO BE UNDERTAKEN BY APPROVED DISTRIBUTORS.
SHOULD SERVICE BE NECESSARY, THIS MUST BE ARRANGED
THROUGH YOUR DISTRIBUTOR OR DEALER WHO WILL ADVISE YOU
OF WHERE TO SEND YOUR VANTAGE-HD FOR SERVICE. UNITS WILL
NOT BE SERVICED IF THEY ARE RETURNED TO CALIBRE UK LTD
WITHOUT A VALID CALIBRE-ISSUED RETURNS AUTHORISATION
NUMBER.
Issue 1.0.2
28 March 2006 © Calibre UK Ltd
Page 30 of 30
Download from Www.Somanuals.com. All Manuals Search And Download.
|