Title Page
®
Portable Management Application
for the
SEHI100TX-22™
User’s Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Notice
Cabletron Systems reserves the right to make changes in speciÞcations and other information
contained in this document without prior notice. The reader should in all cases consult Cabletron
Systems to determine whether any such changes have been made.
The hardware, Þrmware, or software described in this manual is subject to change without notice.
IN NO EVENT SHALL CABLETRON SYSTEMS BE LIABLE FOR ANY INCIDENTAL, INDIRECT,
SPECIAL, OR CONSEQUENTIAL DAMAGES WHATSOEVER (INCLUDING BUT NOT LIMITED
TO LOST PROFITS) ARISING OUT OF OR RELATED TO THIS MANUAL OR THE INFORMATION
CONTAINED IN IT, EVEN IF CABLETRON SYSTEMS HAS BEEN ADVISED OF, KNOWN, OR
SHOULD HAVE KNOWN, THE POSSIBILITY OF SUCH DAMAGES.
Virus Disclaimer
Cabletron has tested its software with current virus checking technologies. However, because no
anti-virus system is 100% reliable, we strongly caution you to write protect and then verify that the
Licensed Software, prior to installing it, is virus-free with an anti-virus system in which you have
conÞdence.
Cabletron Systems makes no representations or warranties to the effect that the Licensed Software is
virus-free.
Copyright © 1998 by Cabletron Systems, Inc. All rights reserved.
Printed in the United States of America.
Order Number: 9031975-E2 April 1998
Cabletron Systems, Inc.
P.O. Box 5005
Rochester, NH 03866-5005
SPECTRUM, MiniMMAC, FNB, Multi Media Access Center, and DNI are registered trademarks,
and Portable Management Application, IRM, IRM2, IRM3, IRBM, ESXMIM, ETSMIM, EMME,
EMM-E6, ETWMIM, FDMMIM, FDCMIM, MicroMMAC, MRXI, MRXI-24, NB20E, NB25E, NB30,
NB35E, NBR-620, SEHI, TRBMIM, TRMM, TRMM-2, TRMM-4, TRMMIM, TRXI, Media Interface
Module, MIM, and Flexible Network Bus are trademarks of Cabletron Systems, Inc.
UNIX and OPENLOOK are trademarks of Unix System Laboratories, Inc. OSF/Motif and Motif
are trademarks of the Open Software Foundation, Inc. X Window System is a trademark of
X Consortium, Inc. Ethernet and XNS are trademarks of Xerox Corporation. Apple and AppleTalk
are registered trademarks of Apple Computer, Inc. Banyan is a registered trademark of Banyan
Systems, Inc. DECnet is a registered trademark of Digital Equipment Corporation. Novell is a
registered trademark of Novell, Inc. CompuServe is a registered trademark of CompuServe. Sun
Microsystems is a registered trademark, and Sun, SunNet, and OpenWindows are trademarks of Sun
Microsystems, Inc.
i
Download from Www.Somanuals.com. All Manuals Search And Download.
Restricted Rights Notice
(Applicable to licenses to the United States Government only.)
1. Use, duplication, or disclosure by the Government is subject to restrictions as set forth in
subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at DFARS
252.227-7013.
Cabletron Systems, Inc., 35 Industrial Way, Rochester, New Hampshire 03867-0505.
2. (a) This computer software is submitted with restricted rights. It may not be used, reproduced, or
disclosed by the Government except as provided in paragraph (b) of this Notice or as otherwise
expressly stated in the contract.
(b) This computer software may be:
(1) Used or copied for use in or with the computer or computers for which it was acquired,
including use at any Government installation to which such computer or computers may
be transferred;
(2) Used or copied for use in a backup computer if any computer for which it was acquired
is inoperative;
(3) Reproduced for safekeeping (archives) or backup purposes;
(4) Modified, adapted, or combined with other computer software, provided that the
modified, combined, or adapted portions of the derivative software incorporating
restricted computer software are made subject to the same restricted rights;
(5) Disclosed to and reproduced for use by support service contractors in accordance with
subparagraphs (b) (1) through (4) of this clause, provided the Government makes such
disclosure or reproduction subject to these restricted rights; and
(6) Used or copied for use in or transferred to a replacement computer.
(c) Notwithstanding the foregoing, if this computer software is published copyrighted computer
software, it is licensed to the Government, without disclosure prohibitions, with the minimum
rights set forth in paragraph (b) of this clause.
(d) Any other rights or limitations regarding the use, duplication, or disclosure of this computer
software are to be expressly stated in, or incorporated in, the contract.
(e) This Notice shall be marked on any reproduction of this computer software, in whole or in part.
ii
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Conventions................................................................................................................... 1-3
SEHI100TX Firmware................................................................................................... 1-7
Year 2000 Compliance ........................................................................................... 1-7
Hub View Front Panel........................................................................................... 2-2
Checking Repeater Status................................................................................... 2-13
Checking Statistics............................................................................................... 2-16
General/Error Statistics............................................................................... 2-17
Managing the Hub...................................................................................................... 2-20
What is a Segmentation Trap?..................................................................................... 3-1
What is a Link Trap?..................................................................................................... 3-2
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Setting Network Circuit Redundancy........................................................................4-1
ConÞguring a Redundant Circuit........................................................................4-2
Monitoring Redundancy..............................................................................................4-6
iv
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1
Introduction to SPMA
for the SEHI100TX-22
How to use the SEHI User’s Guide; manual conventions; contacting Cabletron Global Call Center;
SEHI firmware versions supported by SPMA
The SEHI100TX-22 is an intelligent repeating Fast Ethernet hub, which when
combined with the SEH100TX-22 non-intelligent stackable hub, can provide from
22 to as many as 120 100Base-TX Ethernet connections in a single stack. Each
SEHI100TX-22 and SEH100 TX-22 provides front panel ports for network
connections, and a rear-panel HUBStack Interconnect Bus port for stackable
connections.
The SEHI100TX-22 intelligent stackable hub is designed to manage one or more of
the SEH100TX-22 non-intelligent stackables. It provides 22 100Base-TX network
ports via RJ45 connectors and one optional user-conÞgurable EPIM port (which
allows for ßexible network connection options, including SMA or ST Þber optic
cable, thin coax, or AUI cable). Although the SEHI100TX-22 is the management
device, providing full packet and error statistics for the stack, it can be located
anywhere in the stack.
Each SEH100TX-22 non-intelligent hub provides 22 100Base-TX network ports
via RJ45 connectors and two optional user-conÞgurable EPIM ports. Up to four
SEH100TX-22s can be included in the stack. The entire stack is counted as only
one repeater hop.
The SEHI100TX-22 fully conforms to the IEEE 802.3 Repeater, AUI, and 10BASE-T
speciÞcations. It will transmit re-timed data packets, regenerate preamble, extend
fragments, arbitrate collisions, and automatically partition problem segments.
1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction to SPMA for the SEHI100TX-22
Using the SEHI User’s Guide
Your SPECTRUM Portable Management Application (SPMA) for the
SEHI100TX-22 consists of a number of different applications, each of which
provides a portion of the overall management functionality. Each of these
applications can be accessed from the icon menu (if you are using a management
platform) and from the command line (if you are running in stand-alone mode);
in addition, several applications can also be accessed from within the Hub View, a
graphical display of the SEHI and its ports.
The SEHI UserÕs Guide describes how to use many of the applications included
with the module; note that the instructions provided in this guide apply to the
SEHI100TX regardless of the operating system or management platform you are
using. Instructions for launching each individual function from the command line
(stand-alone mode) are also included in each chapter.
Following is a description of the applications described in this guide; while we
provide as much background information as we can, we do assume that youÕre
familiar with Ethernet networks and general network management concepts:
¥
Chapter 1, Introduction to SPMA for the SEHI100TX-22, describes the
SEHI 100 TX-22 UserÕs Guide and the conventions used in this and other
SPMAmanuals, explains where to Þnd information about the SEHI100TX, and
tells you how to contact Cabletron Systems Global Call Center.
¥
Chapter 2, Using the SEHI100TX Hub View, describes the visual display of
the Hub and explains how to use the mouse within the Hub View. The
operation of some basic functions available only from within the Hub View
(changing the Hub View display, opening menus and windows, enabling and
disabling ports, checking device and port status, and so on) are also described.
¥
¥
Chapter 3, Link/Seg Traps, describes how to conÞgure link and segmentation
traps to suit your management needs. You can access the Link/Seg Traps
application from the icon menu, the Hub View, or the command line.
Chapter 4, Redundancy, describes how to conÞgure redundant circuits to keep
your network connections up and running in the event of a single portÕs
failure. You can access the Redundancy application from the icon menu, the
Hub View, or the command line.
¥
Appendix A, SEHI100TX MIB Components, lists the IETF MIBs supported by
the SEHI100TX, and describes their arrangement in a series of MIB
components. A description of the objects controlled by each component is also
included.
What’s NOT in the SEHI100TX User’s Guide . . .
The following standard SPMA tools are available through the SEHI100TX module
and are explained in the SPECTRUM Portable Management Application Tools
Guide:
1-2
Using the SEHI User’s Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction to SPMA for the SEHI100TX-22
¥
¥
¥
¥
¥
¥
¥
Charts, Graphs, and Meters
Community Names
MIB I,II
MIBTree
TFTP Download
Trap Table
Utilities (Global Community Names, Find MAC Address and TFTP)
Graphing capabilities are provided by an application that is included in HP Network
Node Manager and IBM NetView; therefore, graphs are only available when SPMA is
run in conjunction with one of these network management platforms. If you are running
SPMA in a stand-alone mode or in conjunction with SunNet Manager or Solstice
Enterprise Manager, no graphing options will be displayed on buttons or menus. Note
that the screens displayed in this guide will include the graph-related options where they
are available; please disregard these references if they do not apply.
NOTE
Charts, Graphs, and Meters are accessible from the Hub View and the command
line; the Utilities, and MIBTree applications are accessible from the platform
console window Tools menu, the Stand-alone Launcher applications menu, or the
command line; and the rest of the tool applications (except Telnet) are available
from the icon menu, the Hub View, or the command line. (The Telnet application
is available only from the icon menu or the command line.)
Instructions on discovering Cabletron devices, creating icons, and accessing the
icon menus within your management platform are included in your Installing
and Using SPECTRUM for ... guide. If you are using SPMA for the SEHI100TX in
stand-alone mode Ñ that is, without beneÞt of a speciÞc network management
system Ñ instructions for starting each application from the command line are
included in each chapter of this guide and the SPMA Tools Guide.
Conventions
The family of SPECTRUM Portable Management Applications can work with a
number of different network management systems running on several different
operating systems and graphical user interfaces. This versatility presents two
documentation problems: Þrst, there is no standard terminology; and second, the
appearance of the windows will differ based on the graphical interface in use. For
the sake of consistency, the following conventions will be followed throughout
this and other SPMA guides.
Conventions
1-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction to SPMA for the SEHI100TX-22
Screen Displays
SPMA runs under a variety of different operating systems and graphical user
interfaces. To maintain a consistent presentation, screen displays in this and other
SPMA guides show an OSF/Motif environment. If youÕre used to a different GUI,
donÕt worry; the differences are minor. Buttons, boxes, borders, and menus
displayed on your screen may look a bit different from what you see in the guide,
but theyÕre organized and labelled the same, located in the same places, and
perform the same functions in all screen environments.
Some windows within SPMA applications can be re-sized; those windows will
display the standard window resizing handles employed by your windowing
system. Re-sizing a window doesnÕt re-size the information in the window; it just
you shrink a window, scroll bars will appear as necessary so that you can scroll to
view all the information that is available.
Use the scroll bars
provided to choose
what to display in a
window that’s been
resized
Click here to
display footer
message history
Figure 1-1. Window Conventions
Some windows will also contain a
button; selecting this button
been displayed since the window was Þrst invoked. This window can help you
keep track of management actions you have taken since launching a management
application.
1-4
Conventions
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction to SPMA for the SEHI100TX-22
Figure 1-2. The History Window
Using the Mouse
SPMA document set refer to these buttons as follows:
Button 1
Button 2
Button 3
Figure 1-3. Mouse Buttons
If youÕre using a two-button mouse, donÕt worry. SPMA doesnÕt make use of
mouse button 2. Just click the left button for button 1 and the right mouse button
when instructed to use mouse button 3.
Conventions
1-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction to SPMA for the SEHI100TX-22
Whenever possible, we will instruct you on which mouse button to employ;
however, menu buttons within SPMA applications will operate according to the
convention employed by the active windowing system. By convention, menu
buttons under the Motif windowing environment are activated by clicking the left
mouse button (referred to as mouse button 1 in SPMA documentation), and there
is no response to clicking the right button (mouse button 3). Under
OpenWindows, menu buttons can be activated by clicking the right button, and
convention dictates that the left button activates a default menu option; within
SPMA, that default option will also display the entire menu. Because of this
difference, references to activating a menu button will not include instructions
about which mouse button to use. All other panels from which menus can be
accessed, and all buttons which do not provide access to menus, will operate
according to SPMA convention, as documented.
Getting Help
If you need technical support related to SPMA, or if you have any questions,
comments, or suggestions related to this manual or any of our products, please
feel free to contact the Cabletron Systems Global Call Center. Before calling,
please have the following information ready:
¥
¥
The product name and part number.
The version number of the program that you need help with. SPMA is
modular, which means each application will have a speciÞc revision number.
Where applicable, an INFO button provides the version number; you can also
view the version number for any application by typing the command to start
the application followed by a -v.
You can contact the Cabletron Systems Global Call Center via any of the following
methods:
By phone:
Monday through Friday between 8 AM and 8 PM
Eastern Standard Time at (603) 332-9400
By mail:
Cabletron Systems, Inc.
PO Box 5005
Rochester, NH 03866-5005
By Internet mail:
FTP:
ftp.ctron.com (134.141.197.25)
Login
anonymous
Password
your email address
By BBS:
(603) 335-3358
Modem Setting
8N1: 8 data bits, 1 stop bit, No parity
1-6
Getting Help
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction to SPMA for the SEHI100TX-22
For additional information about Cabletron Systems products, visit our
select Service and Support.
SEHI100TX Firmware
SPMA support for the SEHI100TX has been tested against Þrmware version
1.00.06; if you have an earlier version of Þrmware and experience problems
running SPMA, contact Cabletron Systems Global Support Center for upgrade
information.
As a general rule, Þrmware versions for new products are liable to change rapidly; contact
the Cabletron Systems Global Support for upgrade information for the latest customer
release of Þrmware.
NOTE
Year 2000 Compliance
Previous users of SPMA will note a few display changes related to Year 2000
compliance. All SPMA applications now have the ability to display a four-digit
year value where this information is available. For example, the Stand-alone
Launcher window Ð which uses your workstationÕs system time value to display
the time and date of the last contact change Ð will now display these date values
with eight digits (05/31/1998) instead of six (05/31/98).
Please keep in mind, however, that SPMAÕs ability to display a four-digit year
value in device-speciÞc windows Ð such as the Device Status window available
from the Hub View or the Bridge View Ð is dependent on the ÞrmwareÕs ability to
provide a four-digit value. Not all Þrmware versions support this ability; contact
Cabletron SystemsÕ Global Call Center for information speciÞc to your device
Þrmware.
SEHI100TX Firmware
1-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction to SPMA for the SEHI100TX-22
1-8
SEHI100TX Firmware
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2
Using the SEHI100TX Hub View
Navigating through the Hub View, monitoring hub performance; managing the hub
The heart of SPECTRUM Portable Management Applications (SPMA) for the
SEHI100TX is the Hub View, a graphical interface that gives you access to many of
the functions that provide control over the device.
Using the Hub View
There are two ways to open the Hub View: if you are working within a network
management system, you can select the Hub View option from the icon menu;
speciÞc directions for creating a SEHI100TX icon and accessing the icon menu can
be found in the appropriate Installing and Using SPECTRUM for... guide. If you
are running the SEHI100TX module in a stand-alone mode, type the following at
the command line:
spmarun hubstack <IP address> <community name>
The community name you use to start the module must have at least Read access;
for full management functionality, you should use a community name that
provides Read/Write or Superuser access. For more information on community
names, consult the appropriate Installing and Using SPECTRUM for... guide,
and/or the Community Names chapter in the SPMA Tools Guide.
The spmarun script invoked Þrst in the above command temporarily sets the environment
NOTE
variables SPMA needs to operate; be sure to use this command any time you launch an
application from the command line. This script is automatically invoked when you launch
an application from the icon menu or from within the Hub View.
If there is a hostname mapped to your SEHI100TXÕs IP address, you can use <hostname>
in place of <IP address> to launch the Hub View. Please note, however, that the hostname
is not the same as the device name which can be assigned via Local Management and/or
SPMA; you cannot use the device name in place of the IP address.
2-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the SEHI100TX Hub View
Navigating Through the Hub View
of the window to access various menus and initiate certain management tasks.
The following sections describe the information displayed in the Hub View Front
Panel and how to use the mouse in the Hub View Ports Display.
Front Panel
Device summary information
Figure 2-1. The SEHI100TX Hub View
Hub View Front Panel
In addition to the graphical display of the modules, the Hub View gives you
device level summary information. The following Front Panel information
appears below the port display in the Hub View:
Contact Status is a color code that shows the status of the connection between
SPMA and the device:
¥
¥
Green means a valid connection.
Blue means that SPMA is trying to reach the device but doesnÕt yet know if the
connection will be successful.
¥
Red means that SPMA is unable to contact or has lost contact with the device.
2-2
Using the Hub View
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the SEHI100TX Hub View
Uptime
The time that the device has been running without interruption. The counter
resets to 0 days 00:00:00 (HH:MM:SS) when one of the following occurs:
¥
¥
Power to the device is cycled.
The device is reset manually.
Date and Time
The date and time are taken from the deviceÕs internal clock. You can set the
details.
Device Name
A text Þeld that you can use to help identify the device. You can edit the device
Location
A text Þeld that you can use to help identify the device. You can edit the device
If you have assigned a device name or location that contains more than 18 characters, only
the last 18 will be displayed in the Hub View. Check the Device Status window for the
complete name and/or location, if necessary.
NOTE
IP Address
The deviceÕs Internet Protocol address. You cannot change the SEHI100TXÕs IP
address from SPMA.
MAC Address
The deviceÕs factory-set hardware address. The MAC address cannot be changed.
Using the Hub View
2-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the SEHI100TX Hub View
Figure 2-2. SEHI100TX Hub View Device Menu
The Device menu lets you perform the following:
¥
¥
¥
¥
¥
¥
¥
¥
Open the Device Status window
Open the Repeater Status window
Open the Polling Intervals window
Open the Statistics windows
Create device-level Pie Charts and Graphs or Meters
Change the Port Display Form
Launch the Link/Seg Traps application
Launch the Redundancy application
Graphing capabilities are provided by an application that is included in HP Network
Node Manager and IBM NetView; therefore, graphs are only available when SPMA is
run in conjunction with one of these network management platforms. If you are running
SPMA in a stand-alone mode or in conjunction with SunNet Manager or Solstice
Enterprise Manager, no graphing options will be displayed on buttons or menus. Note
that the screens displayed in this guide will include the graph-related options where they
are available; please disregard these references if they do not apply.
NOTE
2-4
Using the Hub View
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the SEHI100TX Hub View
Note that the Device menu does not provide access to every application which is
available to the SEHI100TX; some information is only available from the Module
or Port menus, and several applications can only be accessed either from the icon
menu (if you are running under a network management platform) or from the
command line (if you are running in stand-alone mode). See Chapter 1,
Introduction to SPMA for the SEHI100TX-22, for a complete list of applications
available to the SEHI100TX and how to access each one.
If you need to call CabletronÕs Global Support about a problem with the Hub
View application, youÕll need the information provided in the Info window
SPMA for the SEHI100TX
application version
SEHI100TX firmware revision,
firmware boot prom version, and
hardware version
Figure 2-3. The Hub Information Window
Clicking mouse button 1 on the Quit button closes all Hub View application
windows; any open applications which can also be accessed from the command
line or from the icon menu will remain open.
Using the Mouse in the Hub View Ports Display
Each device in your SEHI100TX-managed HUBStack will have its own ports
display in the Hub View; you can access the available ports displays by using the
scroll bar located on the right side of the Hub View Ports Display window, as
mouse to access the Module and Port menus and functions.
Using the Hub View
2-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the SEHI100TX Hub View
Port Display Form
Port Status
Using the Module or Device
menus, you can change the port
display form shown in the Port
Status boxes to any one of the
following:
The Port Status display changes
with the type of port display
format selected. Statistical
selections display values in a
statistic/second format. Load
displays traffic as a percentage
of theoretical maximum
capacity. Port Type displays port
status (ON, OFF, NLK, etc.).
Click mouse button 1 to toggle
the port between enabled and
disabled; click mouse button 3
to display the Port menu.
- Load (% of theoretical maximum)
- Traffic (Pkts/sec)
- Collisions (Colls/sec)
Module Type
- Errors (Errors/sec, total or
by type)
Displays the type of module,
or device, whose ports are
currently being displayed in
the Ports Display.
- Frame Sizes (% of total packets)
- Port Type (Admin/Link Status,
Admin Status, or Active Ports)
Module Index
Scroll Bar
Port Index
Indicates the module’s position in
the SEHI100TX-managed stack; the
SEHI100TX itself is always #1
(regardless of its actual location in
the stack). Click mouse button 1 to
open the Module Status window;
click mouse button 3 to display the
Module menu.
Use the scroll bar to
rotate through the Ports
Display for each hub in
the SEHI100TX-
Click mouse button 3 to
display the Port menu.
managed stack.
Figure 2-4. Mousing Around The Ports Display
2-6
Using the Hub View
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the SEHI100TX Hub View
Hub View Port Color Codes
The Port Status boxes in the Hub View are color coded to indicate the portÕs
connection status. The colors are consistent for all Port Display Forms except
Admin Status; the exceptions are noted below.
¥
Green indicates that the port is active; that is, the port has been enabled by
management, has a valid Link signal (if applicable), and is able to
communicate with the station at the other end of the portÕs cable segment.
Note that anAUI or transceiver port will display as active as long as it has been
enabled by management, even if no cable is connected.
¥
¥
Blue indicates that the port has been disabled through management.
Yellow indicates that the port is enabled but does not currently have a valid
connection. This usually indicates that the device at the other end of the
segment is turned off.
¥
Red indicates that the port is enabled, but is not able to pass packets. This
generally means that the port has been segmented by management after
experiencing an excessive number of collisions; for a BNC (thin coax) port,
however, this may only mean that no cable or terminator has been connected.
When the Admin Status port display option is active, only two colors apply: a
port will be displayed in green if it is enabled by management, regardless of
whether or not there is a cable attached or a valid link signal detected; a port
disabled by management will display as blue.
Monitoring Hub Performance
The information displayed in the Hub View can give you a quick summary of
device activity, status, and conÞguration. SPMA can also provide further details
about device performance via its three-level menu structure. The Device, Module,
and give you access to the tools, menus, and windows that let you monitor
speciÞc aspects of device performance, change hub display options, and set
SEHI100TX operating and notiÞcation parameters. Remember, though many
functions will operate the same at each level, those accessed via the Device menu
control or provide information about the SEHI100TX-managed stack as a whole;
those accessed via the Module menu control or provide information about a
single hub in the stack; and those accessed via the Port menu control or provide
information about a single port.
Monitoring Hub Performance
2-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the SEHI100TX Hub View
Figure 2-5. The SEHI100TXÕs Device, Module, and Port Menus
Hub performance data available through these menus includes:
¥
¥
Device, Module, and Port status descriptions.
Device, Module, and Port statistics, which provide a complete breakdown of
packet activity.
¥
Device, Module, and Port-level pie charts, graphs, and meters, for a graphical
representation of the types and levels of trafÞc passing through the device.
(For more information about pie charts, graphs, and meters, see the Charts,
Graphs, and Meters chapter in the SPMA Tools Guide.)
Port Display Form
You can change the type of information displayed for each port in the device by
using the Port Display Form option on the Device and Module menus. Changing
the port display form via the Device menu will affect all ports in the SEHI100TX-
controlled stack; changing the display form via the Module menu will affect only
those ports on the selected device.
To change the port display form:
1. Click on
to display the Device menu, or on the Module Index box
to display the Module menu.
2. Drag down to Port Display Form, then right as necessary to select one of the
port display options.The current selection will be displayed in the Port Display
Form field on the port display.
2-8
Monitoring Hub Performance
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the SEHI100TX Hub View
Port display form options are:
Load
Shows a percentage for each active port that represents that portÕs portion of the
theoretical maximum trafÞc level Ñ for Ethernet interfaces, 10 megabits per
second; for Fast Ethernet interfaces, 100 megabits per second.
Traffic
Displays port trafÞc data in a packets/second format.
Collisions
Displays port trafÞc data in a collisions/second format. The SEHI100TX counts
both receive collisions Ñ those collisions it detects while receiving a transmission
Ñ and transmit collisions Ñ those it detects while transmitting (i.e., a port in the
SEHI100TX-managed stack transmitted one of the colliding packets); however,
those counts are combined and a single total value is displayed.
Errors
Shows port trafÞc errors in an errors/second format. You can display any one of
the following types of errors:
¥
¥
¥
¥
¥
¥
Total errors
Alignment errors
CRC (Cyclic Redundancy Check) errors
Runts
Giants
OOW (Out-of-Window) Collisions
Frame Sizes
Displays a percentage for each active port that represents what portion of that
portÕs trafÞc is of a speciÞc size, measured in bytes. You can display any one of the
following frame sizes:
¥
¥
¥
¥
¥
¥
¥
Runts (packets with fewer than 64 bytes)
64-127
128-255
256-511
512-1023
1024-1518
Giants (packets with more than 1518 bytes)
For the statistical port display form options listed above, three dashes (- - -) will display
for all inactive ports; any active (green) port will display a numeric value, even if itÕs
0.0000.
NOTE
Monitoring Hub Performance
2-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the SEHI100TX Hub View
Port Type
Provides the following administrative information about the port:
¥
Admin/Link Status indicates the connection status of the port:
-
-
-
-
ON indicates that the port has a valid link signal or does not support a link
signal.
OFF indicates that the port has been turned off through management
action.
NLK (No Link) indicates that the port does not have a link to a device at
the other end of the cable, or that there is no cable attached.
SEG (Segmented) indicates that the port has been segmented by the
repeater due to an excessive collision level.
Because BNC thin coax, AUI, and transceiver ports do not support the link feature, the
displayed Admin/Link status for those ports may be misleading: for example, a BNC port
will display as segmented when, in fact, there is no cable or terminator attached or the
cable has been disconnected; an AUI or transceiver port will display as on (with a valid
link signal) even when no cable is attached. Be sure to keep these anomalies in mind when
troubleshooting a device so equipped.
NOTE
¥
Admin Status displays either ON or OFF, an indication of whether
management has the port enabled or disabled. A port can be ON but not
operational; for example, under the Admin display, ports that are segmented
or not linked are shown as ON.
¥
Active Ports displays either YES or NO for any active (green) port, indicating
whether or not that port has seen any trafÞc at all since the device was last
initialized or the counters were last reset; this port display form can tell you
whether any port whose statistics are not currently incrementing has seen
some activity in the past. Non-green (presumably inactive) ports will display
three dashes (---), regardless of their past statistical activity.
Checking Device Status and Updating Front Panel Info
displayed on the Hub View Front Panel and where you can see summary
information about the current state of the device.
To open the Device Status window:
1. Click on
to display the Device menu.
2. Drag down to Status and release.
2-10
Monitoring Hub Performance
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the SEHI100TX Hub View
Figure 2-6. The Device Status Window
Name and Location
These text Þelds help identify this SEHI100TX-controlled HUBStack. The
information you enter in the Name and Location boxes is written to the
SEHI100TXÕs MIB and appears on the Hub View front panel.
Contact
Use the Contact box to record the name and phone number of the person
responsible for the device. Note that the information entered here is not displayed
on the Hub View front panel.
Date and Time
Displays the current date and time from the SEHI100TXÕs internal clock.
Although the Þelds are static in the window, the front panel display is a real-time
presentation.
To change the name, location, contact, date, or time:
1. Highlight the appropriate field and type the new values.
2. Press Enter or Return on the keyboard to save each change before moving
on to another; each change will appear on the front panel as soon as Enter or
Return is pressed.
Monitoring Hub Performance
2-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the SEHI100TX Hub View
If your device Þrmware can accept four-digit year values, the Date Þeld will allow you to
NOTE
enter the year portion in one-, two-, or four-digit format. If you choose to enter one or two
digits for the year, any value greater than or equal to 88 will be presumed to be in the
1900s; a value of 87 or less is presumed to be in the 2000s. No matter which entry format
you choose, the year will still be displayed and set as a four-digit value.
If your device Þrmware cannot accept four-digit year values, the Date Þeld will allow you
to enter the year portion in one- or two-digit format (with leading zeros supplied
automatically for single-digit entries). No presumption is made about the century, and
any two-digit year value (from 00 to 99) will be accepted.
Attempts to set the date may result in one of three different error messages. Two of these
messages will indicate that the wrong number of digits has been used for the year value,
and will indicate the appropriate number of digits to use for the selected device; the third
message will indicate that the entered date is invalid because it is not an actual calendar
date (such as 02/29 in a non-leap year, any month value greater than 12, or any day value
greater than 31).
Chassis Type
Displays the type of chassis used for the device (stand-alone).
Checking Module Status
SEHI100TX-controlled stack. To open the Module Status window:
1. Click mouse button 1 in the Module Index box. (Use the scroll bar to the right
of the ports display to scroll through the available modules.)
or
1. Click mouse button 3 in the Module Index box to display the Module menu.
2. Drag down to Status and release.
Figure 2-7. The Module Status Window
2-12
Monitoring Hub Performance
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the SEHI100TX Hub View
Name
This text Þeld can help identify the module, or device; the information entered
here does not appear anywhere else in the Hub View.
To edit the Module Name:
1. Highlight the text in the Name box and type in a new name.
2. Press Enter or Return on the keyboard to save your changes.
Active Users
This Þeld is not supported by the SEHI100TX-22.
Module Type
The type of module you are viewing.
Checking Repeater Status
SEHI100TX-controlled HUBStack as a whole. To open the Repeater Status
window:
1. Click on the Device button to display the Device menu.
2. Drag down to Repeater Status and release.
Figure 2-8. The Repeater Status Window
Name
This Þeld can help identify the SEHI100TX-controlled stack as a whole; the
information entered here is not displayed anywhere else in the Hub View.
To edit the Repeater Name:
1. Highlight the text in the Name box and type in a new name.
2. Press Enter or Return on the keyboard to save your changes.
Monitoring Hub Performance
2-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the SEHI100TX Hub View
Active Users
This Þeld is not supported by the SEHI100TX-22.
Checking Port Status
controlled HUBStack. To open the Port Status window:
1. Click mouse button 3 in the Port Index or Port Status box to display the Port
menu.
2. Drag down to Status and release.
Figure 2-9. The Port Status Window
Note that the window title includes the module and port number in parentheses;
the rest of the window contains the following Þelds:
Name
This text Þeld can help identify the port; the information entered here is not
displayed anywhere else in the Hub View.
To edit the Name:
1. Highlight the text in the Name box and type in a new name.
2. Press Enter or Return on the keyboard to save your change.
Link Status
The portÕs Link Status tells you whether or not the port has a valid connection to
the node at the other end of the cable segment. The possible Link conditions are:
2-14
Monitoring Hub Performance
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the SEHI100TX Hub View
¥
¥
¥
Active Ñ The port has a valid connection with the device at the other end of
the portÕs cable.
Inactive Ñ The device at the other end of the cable is turned off, there is a
break in the cable, or there is no device or cable connected.
Not Supported Ñ The selected port does not support the Link feature, so the
SEHI100TX cannot determine link status; this value will show only for thin
coax (BNC), AUI, or transceiver ports.
The fact that thin coax (BNC), AUI, and transceiver ports do not support the link feature
can cause some misleading port status indicators: for example, a BNC port may show as
segmented when, in fact, the cable has been disconnected; or an AUI or transceiver port
may appear to have an active link when no cable has been attached. You should keep these
anomalies in mind when troubleshooting a device so equipped.
NOTE
¥
Unknown Ñ The SEHI100TX canÕt determine a link status.
Status
The portÕs Status can be one of three states:
¥
Segmented Ñ A port becomes segmented (that is, disabled by the repeater
module) when the port experiences 32 consecutive collisions, or when the
portÕs collision detector is on for longer than approximately 2 to 3
milliseconds.
Because they do not support the link feature, thin coax (BNC) ports will display as
segmented when there is no cable or terminator attached or the cable or terminator has
been disconnected (i.e., a Òno linkÓ condition).
NOTE
¥
¥
Active Ñ The port is operating normally.
Unknown Ñ The SEHI100TX cannot determine port status.
Active Users
This Þeld is not supported by the SEHI100TX.
Media Type
Indicates the type of cable segment connected to the port. The supported media
types are:
¥
¥
¥
¥
¥
Twisted Pair: RJ45 conn(ector)
BNC EPIM
AUI EPIM
Transceiver Port: AUI EPIM
Twisted Pair: RJ45 EPIM
Monitoring Hub Performance
2-15
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the SEHI100TX Hub View
¥
¥
¥
Multi-Mode Fiber: SMA EPIM
Multi-Mode Fiber: ST EPIM
Single-Mode Fiber: ST EPIM
Topology Type
Indicates how the port is being used. The available types are:
¥
Station Ñ The port is receiving packets from no devices, a single device, or
two devices. Note that a port in station status may actually be connected to
multiple devices; station status simply indicates that no more than two devices
are currently active.
¥
¥
Trunk Ñ The port is receiving packets from three or more devices; it may be
connected to a coax cable with multiple taps, or to a repeater or another MIM.
Unknown Ñ The SEHI100TX cannot determine the topology status.
Checking Statistics
The Hub View can provide a summary of Ethernet statistics at the Device,
statistics contain the same statistical categories at each level.
Figure 2-10. The Repeater Statistics Windows (Device Level)
2-16
Monitoring Hub Performance
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the SEHI100TX Hub View
To view device statistics at the Device, Module, or Port levels:
1. Display the Device, Module, or Port menu by clicking mouse button 3 in the
2. Drag down to Statistics and then right to either General/Errors or Frames
and release.
The Hub View begins counting the selected statistics when you open the window;
counts will be cumulative until you use the Reset button or close the window.
When a device is reset, statistics windows and/or statistics displays in the Hub View may
display very large numbers for one polling interval. This is due to the resetting of the
counters.
NOTE
Because the SEHI100TX does not currently support Protocol counts, the Protocol Þelds
in the Frames window will be grayed-out.
Note that the module statistics windows include the module number in the
window title; the port statistics windows include the module and port numbers in
the window title.
General/Error Statistics
The General/Errors statistics windows display the following Þelds:
Received Bytes
The number of bytes of data received by this device, module, or port since the
window was last opened or reset.
Total Packets
The number of packets of all types received by this device, module, or port since
the window was last opened or reset.
Avg Packet Size
The number of bytes per packet received by this device, module, or port since the
window was last opened or reset. The average packet size is calculated by
dividing the number of bytes received by the number of packets received.
Broadcast Packets
The number of broadcast packets received by this device, module, or port since
the window was last opened or reset. Broadcast packets have a single address
recognized by each station on the net: this address is designated in IP form as
255.255.255.255, or in MAC hexadecimal form as FF-FF-FF-FF-FF-FF. The ARP
and RARP requests sent by bridges and routers are broadcast packets.
Monitoring Hub Performance
2-17
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the SEHI100TX Hub View
Multicast Packets
The number of multicast packets received by this device, module, or port since
the window was last opened or reset. Multicast packets are simultaneously
addressed to more than one address, but fewer than all addresses.
Collisions
The number of collisions recorded by this device, module, or port since the
window was last opened or reset. The SEHI100TX counts both receive collisions
Ñ those detected while a port is receiving data Ñ and transmit collisions Ñ those
detected while a port is transmitting data (i.e., the port has transmitted one of the
colliding packets); however, these counts are combined and a single total value is
displayed. Collisions of this type (called ÒlegalÓ collisions, as opposed to the
OOW collisions described below) are a natural by-product of a busy network; if
you are experiencing high numbers of collisions, it may be time to redirect
network trafÞc by using bridges or routers. Extremely high collision rates can also
indicate a data loop (redundant connections) or a hardware problem (some
station transmitting without listening Þrst).
Total Errors
The number of errors of all types recorded by this device, module, or port since
the window was last opened or reset.
Alignment Errors
The number of misaligned packets recorded since the window was last opened or
reset. Misaligned packets are those which contain any unit of bits which is less
than a byte Ñ in other words, any group of bits fewer than 8. Misaligned packets
can result from a packet formation problem, or from some cabling problem that is
corrupting or losing data; they can also result from packets passing through more
than two cascaded multi-port transceivers (a network design which does not meet
accepted Ethernet spec).
CRC Errors
CRC, or Cyclic Redundancy Check, errors occur when packets are somehow
damaged in transit. When each packet is transmitted, the transmitting device
computes a frame check sequence (FCS) value based on the contents of the packet,
and appends that value to the packet. The receiving station performs the same
computation; if the FCS values differ, the packet is assumed to have been
corrupted and is counted as a CRC error. CRC errors can result from a hardware
problem causing an inaccurate computation of the FCS value, or from some other
transmission problem that has garbled the original data. The CRC error counter
shows the total number of CRC errors recorded since the window was last
opened or reset.
OOW Collisions
The number of out-of-window collisions recorded since the window was last
opened or reset. OOW collisions occur when a station receives a collision signal
while still transmitting, but more than 51.2 µsec (the maximum Ethernet
propagation delay) after the transmission began. There are two conditions which
can cause this type of error: either the networkÕs physical length exceeds IEEE
2-18
Monitoring Hub Performance
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the SEHI100TX Hub View
802.3 speciÞcations, or a node on the net is transmitting without Þrst listening for
carrier sense (and beginning its illegal transmission more than 51.2 µs after the
Þrst station began transmitting). Note that in both cases, the occurrence of the
errors can be intermittent: in the case of excessive network length, OOW collisions
will only occur when the farthest stations transmit at the same time; in the case of
the node which is transmitting without listening, the malfunctioning node may
only fail to listen occasionally, and not all of its failures to listen will result in
OOW collisions Ñ some may simply result in collisions (if the 51.2 µs window has
not yet closed), and some will get through Þne (if no one else happens to be
transmitting).
Runt Frames
The number of received packets smaller than the minimum Ethernet frame size of
64 bytes (excluding preamble). This minimum size is tied to the maximum
propagation time of an Ethernet network segment Ñ the maximum propagation
time is 51.2 µs, and it takes approximately 51.2 µs to transmit 64 bytes of data;
therefore, every node on the segment should be aware that another node is
transmitting before the transmission is complete, providing for more accurate
collision detection. Runts can sometimes result from collisions, and, as such, may
be the natural by-product of a busy network; however, they can also indicate a
hardware (packet formation), transmission (corrupted data), or network design
(more than four cascaded repeaters) problem.
Giant Frames
The number of received packets that are longer than the maximum Ethernet size
of 1518 bytes (excluding preamble). Giant packets typically occur when you have
a jabbering node on your network Ñ one that is continuously transmitting, or
transmitting improperly for short bursts Ñ probably due to a bad transmitter on
the network interface card. Giant packets can also result from packets being
corrupted as they are transmitted, either by the addition of garbage signal, or by
the corruption of the bits that indicate frame size.
The SEHI100TX Error Priority Scheme
Each Cabletron device employs an error priority scheme which determines how
packets with multiple errors will be counted, and ensures that no error packet is
counted more than once. The priority scheme for the SEHI100TX counts errors in
the following order:
1. OOW Collisions
2. Runts
3. Giants
4. Alignment Errors
5. CRC Errors
Monitoring Hub Performance
2-19
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the SEHI100TX Hub View
Knowing the priority scheme employed by the SEHI100TX can tell you a lot about
the error counts you are seeing. For example, you know that the number of
packets counted as CRC errors had only CRC errors Ñ they were of legal size (not
runts or giants) and had no truncated bytes. You also know that any packet less
than 64 bytes long has been counted as a runt, even if it also had alignment
and/or CRC problems (which is likely if the runt is the result of a collision or
other transmission problem).
Frames Statistics
The Frames statistics windows display the following Þelds:
Frame Sizes
¥
¥
¥
¥
¥
¥
¥
Runt Frames (packets smaller than 64 bytes)
64-127 (byte) Frames
128-255 Frames
256-511 Frames
512-1023 Frames
1024-1518 Frames
Giant Frames (packets larger than 1518 bytes)
Because the SEHI100TX does not currently support Protocol counts, the Protocol Þelds
in the Frames window will be grayed-out.
NOTE
Managing the Hub
In addition to the performance information described in the preceding sections,
the Hub View also provides you with the tools you need to conÞgure your
HUBStack and keep it operating properly. Hub management functions include
setting polling intervals, enabling ports at the module and port level, and
disabling ports at the port level.
Setting the Polling Intervals
To set the polling intervals used by SPMA and the SEHI100TX:
1. Click on the Device button to display the Device menu.
2. Drag down to Polling Intervals, and release. The SEHI100TX Polling
2-20
Managing the Hub
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the SEHI100TX Hub View
Figure 2-11. The Polling Intervals Window
3. To activate the desired polling, click mouse button 1 on the selection box to
the right of each polling type field.
4. To change a polling interval, highlight the value you would like to change, and
enter a new value in seconds. Note that the Use Defaults option must not be
selected, or values will revert back to default levels when you click on Apply,
and your changes will be ignored.
5. If you wish to use your new polling interval settings as the default values that
SPMA will use for each SEHI100TX-controlled stack you are managing, use
mouse button 1 to select the Save As Defaults option.
6. If you wish to replace existing values with the current set of default values, use
mouse button 1 to select the Use Defaults option.
7. Click mouse button 1 on the Apply button once your changes are complete.
Changes take effect after the current polling cycle is complete.
You can set the update intervals for the following:
Contact Status
This polling interval controls how often the SEHI100TX is ÒpingedÓ to check
SPMAÕs ability to maintain a connection with the device.
Device General Status
This polling interval controls how often the Hub View Front Panel Information Ñ
such as Uptime, Device Name, and so forth Ñ and some port status information
is updated.
Managing the Hub
2-21
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the SEHI100TX Hub View
Device Configuration
This polling interval controls how often a survey is conducted of the devices
installed in your SEHI100TX-controlled HUBStack.
Port Operational State
This polling interval controls the update of the information displayed in the Port
Status boxes for each port in the device. Port state information includes link state
(the color code) and admin state (on or off).
Statistics
This polling interval controls how often the information displayed in the Port
Status boxes is updated when the Port Display Form is set to a rate or percentage,
and how often the Device, Module, and Port statistics counts are updated.
SPMA generates network trafÞc when it retrieves the above-described information; keep
in mind that shorter intervals mean increased network trafÞc. Range limits for these
polling times are 0-999,999 seconds; however, an entry of 0 will be treated as a 1.
NOTE
Enabling/Disabling Ports
You can enable and disable ports both from the Module menu, which affects all
ports on a single module, or device; or from the Port menu, which affects
individual ports.
To enable or disable an individual port:
1. Click mouse button 1 on the Port Status box to toggle the port On or Off.
or
1. Click mouse button 3 on the Port Index or Port Status box to display the Port
menu.
2. Drag down to Enable or Disable, as appropriate, and release. The selected
port changes color when its state changes. A disabled port is blue.
To enable or disable all ports in a module:
1. Click mouse button 3 on the Module Index box to open the Module menu.
2. Drag down to Enable All Ports or Disable All Ports, as appropriate, and
release.
When disabling all ports on a module, make sure you donÕt disable the port through which
your management station is communicating with the HUBStack, or you will lose contact
with the stack.
!
CAUTION
2-22
Managing the Hub
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3
Link/Seg Traps
About Link and Segmentation traps; enabling and disabling these traps at the device, module, and port
levels
Among the traps which Cabletron devices are designed to generate are traps
which indicate when a repeater port gains or loses a link signal, when the repeater
segments (disconnects) a port due to collision activity, and when a segmented
port becomes active again. In some networks, these Link and Segmentation traps
may be more information than a network manager wants to see. So SPMA
provides you with a means to selectively enable and disable Link and
Segmentation traps. You can turn traps on and off for all ports on the SEHI100TX,
all ports on a selected module or modules, or for individual ports.
SPMA does not accept the trap messages; that task is left to your network management
NOTE
system. (See the appropriate network management system documentation for details
about viewing trap messages.) When this utility is used in stand-alone mode, traps will
either be ignored when they return to the workstation from which you are running SPMA
for the SEHI100TX, or they will turn up at another management workstation which has
been conÞgured to accept traps. Note also that, regardless of the conÞguration performed
using this utility, NO traps will be sent by the device unless its trap table has been
properly conÞgured; see the SEHI100TX hardware manual and/or the Trap Table chapter
in the SPMA Tools Guide for more information.
What is a Segmentation Trap?
CabletronÕs Ethernet repeaters count collisions at each port. If a port experiences
32 consecutive collisions, the repeater segments the port to isolate the source of
the collisions from the rest of the network. When the repeater segments a port, it
generates a portSegmenting trap. As soon as a segmented port receives a good
packet, the repeater reconnects the port to the network and generates a
portUnsegmenting trap.
3-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Link/Seg Traps
Unterminated BNC (thin coax) ports appear in the Hub View as segmented ports. When
you attach a thin coax cable or a 50 Ω terminator to a port, the repeater generates a
portUnsegmenting trap; when you remove the cable or terminator, the repeater
generates a portSegmenting trap. Note also that devices at both ends of the cable will
generate the portUnsegmenting and portSegmenting traps, even if only one end of the
cable has been disconnected.
NOTE
What is a Link Trap?
Some Cabletron Ethernet repeater ports Ñ including RJ45 twisted pair and Þber
optic ports Ñ generate a link signal to monitor the status of their connection with
the device at the other end of the cable segment. If the cable is removed or broken,
the portÕs link status goes to ÒNo LinkÓ and the repeater generates a
portLinkDown trap. When a port in a ÒNo LinkÓ condition receives a link signal,
the port goes to a ÒLinkÓ condition and the repeater generates a portLinkUp trap.
Note that devices at both ends of the disconnected or broken cable will generate
the portLinkDown and portLinkUp traps, even when only one end of the cable
has been removed.
BNC (thin coax), AUI, and transceiver ports do not support a link signal. As described
above, BNC ports respond to changes in link status by generating portSegmenting and
portUnsegmenting traps; AUI and transceiver ports do not respond at all to changes in
link status (unless the port has been segmented due to excessive collisions), and will
always display as on, even if no cable is connected.
NOTE
Enabling and Disabling Link/Seg Traps
Although each Cabletron device comes with a number of traps built into the
Þrmware, no device will generate these traps unless it is conÞgured to do so. This
can be accomplished via Local Management (by enabling traps and entering your
workstationÕs IP address in the Community Names screen), or via the SPMA Trap
Table utility, accessible from the icon menu or from the command line. Once traps
as a whole have been enabled, you can use the Link/Seg Traps feature to
selectively enable and disable link and segmentation traps as required by your
network management needs.
To open the Repeater Link/Seg Traps window:
from the icon:
1. Click on the appropriate SEHI100TX icon to display the icon menu.
2. Drag down to Link/Seg Traps and release.
3-2
What is a Link Trap?
Download from Www.Somanuals.com. All Manuals Search And Download.
Link/Seg Traps
from the Hub View:
1. Click on
to display the Device menu.
2. Drag down to Link/Seg Traps and release.
from the command line (stand-alone mode):
1. From the appropriate directory, type
spmarun r4hwtr <IP address> <community name>
The spmarun script invoked Þrst in the above command temporarily sets the environment
variables SPMA needs to operate; be sure to use this command any time you launch an
application from the command line. This script is automatically invoked when you launch
an application from the icon menu or from within the Hub View.
NOTES
If you wish to change any Link/Seg Trap settings, be sure to use a community name with
at least Read/Write access. If you only wish to view current settings, a community name
with Read access will be sufÞcient.
If there is a hostname mapped to your SEHI100TXÕs IP address, you can use
<hostname> in place of <IP address> to launch this application. Please note, however,
that the hostname is not the same as the device name which can be assigned via Local
Management and/or SPMA; you cannot use the device name in place of the IP address.
Figure 3-1. The Repeater Link/Seg Traps Window
Enabling and Disabling Link/Seg Traps
3-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Link/Seg Traps
Configuring Link/Seg Traps for the Repeater
To enable or disable Link and Segmentation traps for all ports on a repeater:
1. In the Repeater Link/Seg Traps window, click mouse button 1 on the repeater
interface for which you would like to configure link and segmentation traps.
2. Click mouse button 1 on
; the Channel X Link/Seg Traps
Figure 3-2. The Channel X Link/Seg Traps Window
3. In the Link Traps field, click mouse button 1 on the appropriate selection to
Enable or Disable link traps for the repeater.
4. In the Segmenting Traps field, click mouse button 1 on the appropriate
selection to Enable or Disable segmenting traps for the repeater.
5. Click mouse button 1 on
to save your changes; the current status
will be displayed in each field to the right of the field name. Click on
to exit the window.
Viewing and Configuring Link/Seg Traps for Hub Modules
To enable or disable Link and Segmentation traps for all ports on the selected hub
module or modules:
1. In the Repeater Link/Seg Traps window, select a repeater interface in the
scroll list.
2. Click mouse button 1 on
will appear.
3-4
Enabling and Disabling Link/Seg Traps
Download from Www.Somanuals.com. All Manuals Search And Download.
Link/Seg Traps
Figure 3-3. The Module Traps Window
3. In the Module Traps window, click mouse button 1 to select the module for
which you wish to configure link and segmentation traps.
•
If the Set Trap Status For field displays Selected Modules (the default
setting), you can click to select any modules; to de-select any highlighted
module, click on it again.
•
If the selection All Modules is displayed in the Set Trap Status For field,
all available modules will be automatically selected; if you de-select any
module, the Set Trap Status For field will automatically revert to the
Selected Modules setting.
To change the setting in the Set Trap Status For field, click on the currently
displayed setting, and drag down to select a new setting.
4. Click on the appropriate selection in the LinkTraps field to Enable or Disable
link traps for the selected modules, as desired.
5. Click on the appropriate selection in the SegmentingTraps field to Enable or
Disable segmenting traps, as desired.
6. Click on
window.
to save your changes; click on
to exit the
Enabling and Disabling Link/Seg Traps
3-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Link/Seg Traps
Viewing and Configuring Link/Seg Traps for Ports
To enable or disable Link and Segmentation traps for individual ports:
1. In the Repeater Link/Seg Traps window, select a repeater in the scroll list.
2. Click mouse button 1 on
will appear.
Figure 3-4. The Port Traps Window
3. In the Port Traps window, click mouse button 1 to select the port or ports for
which you wish to configure traps.
•
•
•
If the Set Trap Status For field displays Selected Ports (the default
setting), you can click to select any ports; to de-select any highlighted port,
click on it again.
If the selection All Ports on Module is displayed in the SetTrap Status For
field, you can select only one port at a time; trap status will be set for all
ports on the same module as the selected port.
If the selection All Ports on Repeater is displayed in the Set Trap Status
For field, all available ports will be automatically selected; if you de-select
any port, the Set Trap Status For field will automatically revert to the
Selected Ports setting.
3-6
Enabling and Disabling Link/Seg Traps
Download from Www.Somanuals.com. All Manuals Search And Download.
Link/Seg Traps
To change the setting in the Set Trap Status For field, click on the currently
displayed setting, and drag down to select a new setting.
4. Click on the appropriate selection in the LinkTraps field to Enable or Disable
link traps for the selected ports, as desired.
5. Click on the appropriate selection in the SegmentingTraps field to Enable or
Disable segmenting traps, as desired.
6. Click on
window.
to save your changes; click on
to exit the
Enabling and Disabling Link/Seg Traps
3-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Link/Seg Traps
3-8
Enabling and Disabling Link/Seg Traps
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
Repeater Redundancy
Configuring and enabling redundant circuits; monitoring redundant circuits
Setting Network Circuit Redundancy
The redundancy application gives you the ability to deÞne redundant circuits for
your SEHI100TX to ensure that critical network connections remain operational.
Each circuit has a designated primary port and one or more backup ports. The
SEHI100TX monitors the link status of the primary portÕs connection to one or
more network IP addresses; if the link fails, the SEHI100TX automatically
switches trafÞc to a backup port.
Before you conÞgure redundancy, make sure that only the primary physical link is
connected to the network. If a backup port is connected before you conÞgure and enable
redundancy, you create a data loop.
NOTE
To open the main Repeater Redundancy window:
from the icon:
1. Click on the appropriate device icon to display the icon menu.
2. Drag down to Redundancy and release.
from the Hub View:
1. Click on
to display the Device menu.
2. Drag down to Redundancy and release.
4-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Repeater Redundancy
from the command line (stand-alone mode):
1. From the appropriate directory, type:
spmarun r4red <IP address> <community name>
The spmarun script invoked Þrst in the above command temporarily sets the environment
variables SPMA needs to operate; be sure to use this command any time you launch an
application from the command line. The script is automatically invoked when you launch
the application from the icon menu or from within the Hub View.
NOTES
If you wish to change any redundancy settings, be sure to use a community name with at
least Read/Write access. If you only wish to view current settings, a community name
with Read access will be sufÞcient.
If there is a hostname mapped to your SEHI100TXÕs IP address, you can use <hostname>
in place of <IP address> to launch this application. Please note, however, that the
hostname is not the same as the device name which can be assigned via Local
Management and/or SPMA; you cannot use the device name in place of the IP address.
Figure 4-1. The Repeater Redundancy Window
Configuring a Redundant Circuit
To establish or edit a redundant circuit:
1. In the Repeater Redundancy window, click mouse button 1 on the repeater
interface for which you would like to edit or establish a redundant circuit, then
click
4-2
Setting Network Circuit Redundancy
Download from Www.Somanuals.com. All Manuals Search And Download.
Repeater Redundancy
Figure 4-2. The Channel X Redundancy Window
2. If you want to change a circuit’s name or the number of retries, highlight the
appropriate circuit and click
. The Change Circuit
Figure 4-3. The Change Circuit Window
Setting Network Circuit Redundancy
4-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Repeater Redundancy
a. In the Name box, enter a new circuit name (up to 16 alphanumeric
characters).
b. In the Retries box, enter the number of retries — that is, the number of
times the SEHI100TX tests the connection to the first IP address listed in
the Circuit Addresses list box before it gives up and moves on to the next
address. The valid range of retries you can enter into this field is 0-16.
c. Be sure to click on
changes.
before exiting the window to save your
3. With the appropriate Circuit Name highlighted, click
to access the
Figure 4-4. The Add Circuit Address Window
You can use this window to define IP addresses of up to 8 devices on the
network. These addresses identify the destination nodes that the SEHI100TX
looks for to determine the status of the active link. If the device determines
that it has lost the link with the first address in the Circuit Addresses list, it
checks the link status with the next address. If it can’t establish a link with any
address in the list, the device switches traffic to a backup port.
a. To add a circuit address, enter a valid network IP address and then click
. Repeat as necessary to add additional addresses. Click
to exit the window.
The SEHI100TX will poll the circuit addresses in the order they were entered.
NOTE
b. To delete a circuit address, highlight the address in the Circuit Addresses
list in the Channel X Redundancy window, and click
.
4. Use the bottom half of the Channel X Redundancy window to define the
primary/active and backup ports for a Circuit:
a. In the Circuit list, highlight the Circuit Name of interest, and click
to ensure that the Status of the circuit is set to
Disabled before configuring the port list.
4-4
Setting Network Circuit Redundancy
Download from Www.Somanuals.com. All Manuals Search And Download.
Repeater Redundancy
b. Specify up to 8 ports that will act as the redundant connections by using
the Module and Port boxes to indicate each port, and then clicking on
to enter each port into the circuit.
c. By default, all ports are created as Inactive Backup ports.You should
designate both a Primary port and an Active port. Typically, you would
configure the same port to be both Primary and Active, but this is not
required.
To select a primary port, click button 1 on a port to highlight it, then click
. Usually, the Primary port will also be your active port.
Should your Primary port not be designated as the active port, it will
switch to Backup/Inactive status when the circuit is initially enabled, but it
will become the active port on the execution of the next test sequence
(assuming it has a valid link at the time of testing).
To select the initially active port, click on a port (whether or not it has
already been selected as Primary), and click
. The port
designated as Active will be the initial port through which the link is
checked. Should the active port fail, redundancy will start at the top of the
port list and activate the next backup port, then work through the
remaining ports in sequence should the first backup fail.
All backup ports will be disabled as soon as you enable the redundant circuit. The ports
remain disabled until they become active due to primary port failure. If you disable the
redundant circuit, you must manually enable each backup port in that circuit.
NOTES
Note also that if an active port fails, and then is repaired, it is not returned to active status
until the circuit has been Tested (unless all other backup ports on the circuit have failed in
the interim).
5. Once you have configured all the ports that compose the redundant circuit,
enable the circuit by clicking
.
Be sure to make all physical connections to the backup ports once the redundant circuit
has been conÞgured and enabled.
NOTE
To clear the settings in one circuit, highlight the Circuit Name that you want to
clear, and click on
.
Setting Network Circuit Redundancy
4-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Repeater Redundancy
To clear all redundancy conÞgurations, click on
portion of the window. Reset does the following:
in the All Circuits
¥
¥
¥
¥
Deletes all entries in the Circuit Addresses box
Changes the status of every Circuit to Disabled
Reverts to previous Circuit Name(s)
Clears all module and port entries
After clearing redundancy settings by either method, backup ports remain disabled until
you manually reenable them so that data loops do not occur. Before you enable the ports,
disconnect their physical connections.
NOTE
Monitoring Redundancy
Once you have conÞgured your redundant circuits, you can use the Þelds in the
All Circuits box to set the parameters that the SEHI100TX uses to periodically test
each of the circuits.
The circuit test checks the current status of every port link, both primary and
backup, by polling the IP addresses in each circuitÕs Polling Addresses list
through each port conÞgured as part of the circuit. This test can be performed at a
pre-determined time, or manually at any time. If the test detects any problems
with the ports on a circuit, whether active or backup, it will issue traps identifying
the circuit and its problem ports.
SPMA does not accept the trap messages; that task is left to your network management
system. (See the appropriate network management system documentation for details
about viewing trap messages.) Note also that NO traps will be sent by the device unless
its trap table has been properly conÞgured; see the SEHI100TX hardware manual and/or
the Trap Table chapter in the SPMA Tools Guide for more information.
NOTE
The testing begins at each circuitÕs currently active port; all ports are tested in
sequence. Once testing is Þnished, the circuits will be reset so that the port
designated as Primary will become the active port; if the primary port is not
operational, the next operational backup port will be activated.
The SEHI100TX automatically polls all enabled circuits through the Primary port
and all Backup ports at the time speciÞed in the Test Time box. If the Þrst poll fails
(results in a no link condition with all of the circuit IP addresses), the SEHI100TX
checks the circuitÕs Retries Þeld. If Retries is greater than 0, the SEHI100TX waits
the number of seconds speciÞed in the Poll Interval Þeld, and then polls the
circuit again.
4-6
Monitoring Redundancy
Download from Www.Somanuals.com. All Manuals Search And Download.
Repeater Redundancy
To set the Poll Interval:
1. In the All Circuits box, type in a new value in the Poll Interval field and click
. Poll Interval is the time in seconds between retries (if the first
attempt is unsuccessful).
To set the Test Time:
1. In the All Circuits box, type a new test time in the Test Time field in a 24-hour
HH:MM:SS format and click
. The Test Time is the time of day when
the SEHI100TX polls the addresses listed in each of the enabled circuits.
To immediately test all enabled circuits:
1. Click
in the All Circuits box.
Monitoring Redundancy
4-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Repeater Redundancy
4-8
Monitoring Redundancy
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A
SEHI100TX MIB Structure
SEHI100TX management information base configuration
IETF MIB Support
In addition to its proprietary features, the SEHI100TX currently supports the
following IETF MIB:
¥
RFC 1213 MIB for Network Management of TCP/IP-based Internets: MIB-II
SEHI100TX MIB Structure
CabletronÕs newer intelligent devices Ñ like the SEHI100TX Ñ organize MIB data
into a series of Òcomponents.Ó A MIB component is a logical grouping of MIB
data, and each group controls a deÞned set of objects. For example, SEHI100TX
repeater information resides in its Repeater component; more generic device and
port information resides in the SEHI100TX Chassis MGR component.
The SEHI100TX MIB consists of Þve components, each of which is described
below. To see the names of the MIB components in your SEHI100TX, bring up the
Community Names application, or use any SNMP Get operation that will allow
you to view the contents of the chCompTable.
The SEHI100TX MIB consists of the following components:
SEHI100TX Chassis MGR
The Chassis MGR MIB component contains most of the basic information about
the SEHI100TX, including: the SEHI100TXÕs MIB component information (in the
chCompTable), device names, hardware revision numbers, MAC and IP
addresses, the current time and date, and information related to redundancy,
alarms, and TFTP download. The system, interfaces, at, ip, icmp, udp, and snmp
groups from MIB-II are also included. The community names assigned to this
MIB component provide the gateway that all SPMA applications use to access all
A-1
Download from Www.Somanuals.com. All Manuals Search And Download.
SEHI100TX MIB Structure
information in the other components, even if those components have different
community names; the Chassis MGR community names are the same as those
assigned via Local Management.
SEHI100TX LIM
The SEHI100TX LIM, or Local Management, component contains the objects that
provide out-of-band management via the Console port on the SEHI100TXÕs front
panel. No objects from this component are used for remote management.
Repeater One
The Repeater MIB component controls all repeater functionality on the
SEHI100TX. These functions include port count, port enable/disable, port status,
board number, repeater statistics (packets, bytes, collisions, errors, etc.), protocol
counts, and frame sizes; also included are the alarm, redundancy, source
addressing, and trap functions. Note that the default community names for the
Repeater MIB component will always be different from the default names
assigned to all the other components.
SEHI100TX Host Services
The Host Services MIB component contains the objects that provide the
SEHI100TX with its IP functionality Ñ essentially, those functions which allow
the SEHI100TX to operate over a network Ñ including functions such as ping,
Telnet, and TFTP.
SEHI100TX IP Services
The IP Services MIB component is not currently used by the SEHI100-TX, but is
reserved for future use.
A Brief Word About MIB Components and Community Names
In the original version of the component MIB architecture, each MIB component is
protected by its own set of user-conÞgurable Read-Only, Read/Write, and Super-
User community names. These names determine the level of access that will be
granted to the information controlled by each individual component. For these
devices, the central point of access for remote management is provided by the
Chassis MGR MIB component Ñ that is, if you deÞne your device icon or launch
a management application using the read-only, read/write, or super-user
community name assigned to the Chassis MGR MIB component, your SPMA
application is granted the appropriate level of access (read-only, read/write, or
super-user) to all of that deviceÕs MIB information Ñ even if the other MIB
components have different community names (as will occur of necessity if the
SEHI100TX has multiple Repeater MIB components, each of which must have a
unique set of community names).
A-2
SEHI100TX MIB Structure
Download from Www.Somanuals.com. All Manuals Search And Download.
SEHI100TX MIB Structure
The set of community names you assign via Local Management are those which apply to
NOTE
the SEHI100TX Chassis MGR MIB component.
Newer versions of devices with this component-based MIB architecture have
been simpliÞed somewhat; these devices support a single, global set of community
names, with small modiÞcations added automatically to accommodate multiple
instances of the same MIB component (such as network components). Again,
deÞning your device icon or launching a management application with one of
these global community names gives SPMA access to all MIB information.
Where community names may become an issue, however, is when you are using
the MIBTree or any similar MIB-based tool (such as those provided by SunNet
Manager or HP Network Node Manager) to access MIB information. For these
kinds of tools, you must supply the precise community name assigned to the
component that contains the information you want. For devices which support
the original component-based MIB architecture Ñ such as the SEHI100TX, this
means you must use the exact community name you have assigned to a speciÞc
component to access that componentÕs MIB information. (Again, note that the
SEHI100TXÕs Repeater components always have unique community names.) For
devices which support the new global community names, you must make note of
the automatic modiÞcations that are made for network components, and use
those speciÞc community names when trying to access information stored in
those components.
The MIB component descriptions provided above will serve as a roadmap for
determining where the information youÕre interested in is located; you can use the
SPMA Community Names tool (described in Chapter 3 of the SPMA Tools Guide)
to determine whether your version of Þrmware supports the original component-
based MIB architecture, or the new global community names. The Community
Names tool also allows you to both view and set the community names which
apply to your device.
SEHI100TX MIB Structure
A-3
Download from Www.Somanuals.com. All Manuals Search And Download.
SEHI100TX MIB Structure
A-4
SEHI100TX MIB Structure
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
M
S
N
O
T
P
port display form
U
R
V
Index-2
Download from Www.Somanuals.com. All Manuals Search And Download.
|