SWPIM-BRI
Installation Guide
LNK
STS
SWPIM-BRI
9033038-02
Download from Www.Somanuals.com. All Manuals Search And Download.
Only qualified personnel should perform installation
procedures.
NOTICE
Cabletron Systems reserves the right to make changes in specifications and other information
contained in this document without prior notice. The reader should in all cases consult Cabletron
Systems to determine whether any such changes have been made.
The hardware, firmware, or software described in this manual is subject to change without notice.
IN NO EVENT SHALL CABLETRON SYSTEMS BE LIABLE FOR ANY INCIDENTAL,
INDIRECT, SPECIAL, OR CONSEQUENTIAL DAMAGES WHATSOEVER (INCLUDING BUT
NOT LIMITED TO LOST PROFITS) ARISING OUT OF OR RELATED TO THIS MANUAL OR
THE INFORMATION CONTAINED IN IT, EVEN IF CABLETRON SYSTEMS HAS BEEN
ADVISED OF, KNOWN, OR SHOULD HAVE KNOWN, THE POSSIBILITY OF SUCH
DAMAGES.
Cabletron Systems, Inc.
35 Industrial Way
Rochester, NH 03867
2000 Cabletron Systems, Inc.
All Rights Reserved
Printed in the United States of America
Order Number: 9033038-02 April 2000
Cabletron Systems, SPECTRUM, and LANVIEW are registered trademarks and SmartSwitch is a
trademark of Cabletron Systems, Inc.
All other product names mentioned in this manual may be trademarks or registered trademarks of
their respective companies.
FCC NOTICE
This device complies with Part 15 of the FCC rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial environment.
This equipment uses, generates, and can radiate radio frequency energy and if not installed in
accordance with the operator’s manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause interference in which case the user
will be required to correct the interference at his own expense.
WARNING: Changes or modifications made to this device which are not expressly approved by the
party responsible for compliance could void the user’s authority to operate the equipment.
SWPIM-BRI Installation Guide
i
Download from Www.Somanuals.com. All Manuals Search And Download.
Notice
INDUSTRY CANADA NOTICE
This digital apparatus does not exceed the Class A limits for radio noise emissions from digital
apparatus set out in the Radio Interference Regulations of the Canadian Department of
Communications.
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables
aux appareils numériques de la class A prescrites dans le Règlement sur le brouillage radioélectrique
édicté par le ministère des Communications du Canada.
NOTICE: The Industry Canada label identifies certified equipment. This certification means that the
equipment meets telecommunications network protective, operational and safety requirements as
prescribed in the appropriate Terminal Equipment Technical Requirements documents (s). The
department does not guarantee the equipment will operate to the user’s satisfaction.
Before installing this equipment, users should ensure that it is permissible to be connected to the
facilities of the local telecommunications company. The equipment must also be installed using an
acceptable method of connection. The customer should be aware that compliance with the above
conditions may not prevent degradation of service in some situations.
Repairs to certified equipment should be coordinated by a representative designated by the supplier.
Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give
the telecommunications company cause to request the user to disconnect the equipment.
Users should ensure for their own protection that the electrical ground connections of the power
utility, telephone lines and internal metallic water pipe system, if present, are connected together. This
precaution may be particularly important in rural areas. Caution: Users should not attempt to make
such connections themselves, but should contact the appropriate electric inspection authority, or
electrician, as appropriate.
NOTICE: The Ringer Equivalence Number (REN) assigned to each terminal device provides an
indication of the maximum number of terminals allowed to be connected to a telephone interface. The
termination on an interface may consist of any combination of devices subject only to the requirement
that the sum of the ringer equivalence Numbers of all the devices does not exceed 5.
AUSTRALIAN TELECOM
This equipment has been tested and is compliant
with ACA TS 031.
N826
VCCI NOTICE
This is a Class A product based on the standard of the Voluntary Control Council for Interference by
Information Technology Equipment (VCCI). If this equipment is used in a domestic environment,
radio disturbance may arise. When such trouble occurs, the user may be required to take corrective
actions.
ii
SWPIM-BRI Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Notice
CABLETRON SYSTEMS, INC.
PROGRAM LICENSE AGREEMENT
IMPORTANT: THIS LICENSE APPLIES FOR USE OF PRODUCT IN THE FOLLOWING
GEOGRAPHICAL REGIONS:
CANADA
MEXICO
CENTRAL AMERICA
SOUTH AMERICA
BEFORE OPENING OR UTILIZING THE ENCLOSED PRODUCT,
CAREFULLY READ THIS LICENSE AGREEMENT.
This document is an agreement (“Agreement”) between You, the end user, and Cabletron
Systems, Inc. (“Cabletron”) that sets forth your rights and obligations with respect to the Cabletron
software program (“Program”) in the package. The Program may be contained in firmware, chips or
other media. UTILIZING THE ENCLOSED PRODUCT, YOU ARE AGREEING TO BECOME
BOUND BY THE TERMS OF THIS AGREEMENT, WHICH INCLUDES THE LICENSE AND
THE LIMITATION OF WARRANTY AND DISCLAIMER OF LIABILITY. IF YOU DO NOT
AGREE TO THE TERMS OF THIS AGREEMENT, RETURN THE UNOPENED PRODUCT TO
CABLETRON ORYOUR DEALER, IF ANY, WITHIN TEN (10) DAYS FOLLOWING THE DATE
OF RECEIPT FOR A FULL REFUND.
IF YOU HAVE ANY QUESTIONS ABOUT THIS AGREEMENT, CONTACT CABLETRON
SYSTEMS +1-603-332-9400. Attn: Legal Department.
1.
LICENSE. You have the right to use only the one (1) copy of the Program provided in this
package subject to the terms and conditions of this License Agreement.
You may not copy, reproduce or transmit any part of the Program except as permitted by the
Copyright Act of the United States or as authorized in writing by Cabletron.
2.
OTHER RESTRICTIONS. You may not reverse engineer, decompile, or disassemble the
Program.
3.
APPLICABLE LAW. This License Agreement shall be interpreted and governed under the
laws and in the state and federal courts of New Hampshire. You accept the personal jurisdiction and
venue of the New Hampshire courts.
4.
EXPORT REQUIREMENTS. You understand that Cabletron and its Affiliates are subject to
regulation by agencies of the U.S. Government, including the U.S. Department of Commerce, which
prohibit export or diversion of certain technical products to certain countries, unless a license to export
the product is obtained from the U.S. Government or an exception from obtaining such license may be
relied upon by the exporting party.
If the Program is exported from the United States pursuant to the License Exception CIV under
the U.S. Export Administration Regulations, You agree that You are a civil end user of the Program
and agree that You will use the Program for civil end uses only and not for military purposes.
SWPIM-BRI Installation Guide
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
Notice
If the Program is exported from the United States pursuant to the License Exception TSR under
the U.S. Export Administration Regulations, in addition to the restriction on transfer set forth in
Sections 1 or 2 of this Agreement, You agree not to (i) reexport or release the Program, the source
code for the Program or technology to a national of a country in Country Groups D:1 or E:2 (Albania,
Armenia, Azerbaijan, Belarus, Bulgaria, Cambodia, Cuba, Estonia, Georgia, Iraq, Kazakhstan,
Kyrgyzstan, Laos, Latvia, Libya, Lithuania, Moldova, North Korea, the People’s Republic of China,
Romania, Russia, Rwanda, Tajikistan, Turkmenistan, Ukraine, Uzbekistan, Vietnam, or such other
countries as may be designated by the United States Government), (ii) export to Country Groups D:1
or E:2 (as defined herein) the direct product of the Program or the technology, if such foreign
produced direct product is subject to national security controls as identified on the U.S. Commerce
Control List, or (iii) if the direct product of the technology is a complete plant o r any major
component of a plant, export to Country Groups D:1 or E:2 the direct product of the plant or a major
component thereof, if such foreign produced direct product is subject to national security controls as
identified on the U.S. Commerce Control List or is subject to State Department controls under the
U.S. Munitions List.
5.
UNITED STATES GOVERNMENT RESTRICTED RIGHTS. The enclosed Product (i)
was developed solely at private expense; (ii) contains “restricted computer software” submitted with
restricted rights in accordance with section 52.227-19 (a) through (d) of the Commercial Computer
Software-Restricted Rights Clause and its successors, and (iii) in all respects is proprietary data
belonging to Cabletron and/or its suppliers. For Department of Defense units, the Product is considered
commercial computer software in accordance with DFARS section 227.7202-3 and its successors, and
use, duplication, or disclosure by the Government is subject to restrictions set forth herein.
6.
EXCLUSION OF WARRANTY. Except as may be specifically provided by Cabletron in
writing, Cabletron makes no warranty, expressed or implied, concerning the Program (including its
documentation and media).
CABLETRON DISCLAIMS ALL WARRANTIES, OTHER THAN THOSE SUPPLIED TO
YOU BY CABLETRON IN WRITING, EITHER EXPRESS OR IMPLIED, INCLUDING BUT
NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, WITH RESPECT TO THE PROGRAM, THE ACCOMPANYING
WRITTEN MATERIALS, AND ANY ACCOMPANYING HARDWARE.
7.
NO LIABILITY FOR CONSEQUENTIAL DAMAGES. IN NO EVENT SHALL
CABLETRON OR ITS SUPPLIERS BE LIABLE FOR ANY DAMAGES WHATSOEVER
(INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS, PROFITS,
BUSINESS INTERRUPTION, LOSS OF BUSINESS INFORMATION, SPECIAL, INCIDENTAL,
CONSEQUENTIAL, OR RELIANCE DAMAGES, OR OTHER LOSS) ARISING OUT OF THE
USE OR INABILITY TO USE THIS CABLETRON PRODUCT, EVEN IF CABLETRON HAS
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. BECAUSE SOME STATES DO
NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR
INCIDENTAL DAMAGES, OR IN THE DURATION OR LIMITATION OF IMPLIED
WARRANTIES IN SOME INSTANCES, THE ABOVE LIMITATION AND EXCLUSIONS MAY
NOT APPLY TO YOU.
iv
SWPIM-BRI Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Notice
CABLETRON SYSTEMS SALES AND SERVICE, INC.
PROGRAM LICENSE AGREEMENT
IMPORTANT: THIS LICENSE APPLIES FOR USE OF PRODUCT IN THE UNITED
STATES OF AMERICA AND BY UNITED STATES OF AMERICA
GOVERNMENT END USERS.
BEFORE OPENING OR UTILIZING THE ENCLOSED PRODUCT,
CAREFULLY READ THIS LICENSE AGREEMENT.
This document is an agreement (“Agreement”) between You, the end user, and Cabletron Systems
Sales and Service, Inc. (“Cabletron”) that sets forth your rights and obligations with respect to the
Cabletron software program (“Program”) in the package. The Program may be contained in firmware,
chips or other media. UTILIZING THE ENCLOSED PRODUCT, YOU ARE AGREEING TO
BECOME BOUND BY THE TERMS OF THIS AGREEMENT, WHICH INCLUDES THE
LICENSE AND THE LIMITATION OF WARRANTY AND DISCLAIMER OF LIABILITY. IF
YOU DO NOT AGREE TO THE TERMS OF THIS AGREEMENT, RETURN THE UNOPENED
PRODUCT TO CABLETRON OR YOUR DEALER, IF ANY, WITHIN TEN (10) DAYS
FOLLOWING THE DATE OF RECEIPT FOR A FULL REFUND.
IF YOU HAVE ANY QUESTIONS ABOUT THIS AGREEMENT, CONTACT CABLETRON
SYSTEMS +1-603-332-9400. Attn: Legal Department.
1.
LICENSE. You have the right to use only the one (1) copy of the Program provided in this
package subject to the terms and conditions of this License Agreement.
You may not copy, reproduce or transmit any part of the Program except as permitted by the
Copyright Act of the United States or as authorized in writing by Cabletron.
2.
OTHER RESTRICTIONS. You may not reverse engineer, decompile, or disassemble the
Program.
3.
APPLICABLE LAW. This License Agreement shall be interpreted and governed under the
laws and in the state and federal courts of New Hampshire. You accept the personal jurisdiction and
venue of the New Hampshire courts.
4.
EXPORT REQUIREMENTS. You understand that Cabletron and its Affiliates are subject to
regulation by agencies of the U.S. Government, including the U.S. Department of Commerce, which
prohibit export or diversion of certain technical products to certain countries, unless a license to export
the product is obtained from the U.S. Government or an exception from obtaining such license may be
relied upon by the exporting party.
If the Program is exported from the United States pursuant to the License Exception CIV under
the U.S. Export Administration Regulations, You agree that You are a civil end user of the Program
and agree that You will use the Program for civil end uses only and not for military purposes.
SWPIM-BRI Installation Guide
v
Download from Www.Somanuals.com. All Manuals Search And Download.
Notice
If the Program is exported from the United States pursuant to the License Exception TSR under
the U.S. Export Administration Regulations, in addition to the restriction on transfer set forth in
Sections 1 or 2 of this Agreement, You agree not to (i) reexport or release the Program, the source
code for the Program or technology to a national of a country in Country Groups D:1 or E:2 (Albania,
Armenia, Azerbaijan, Belarus, Bulgaria, Cambodia, Cuba, Estonia, Georgia, Iraq, Kazakhstan,
Kyrgyzstan, Laos, Latvia, Libya, Lithuania, Moldova, North Korea, the People’s Republic of China,
Romania, Russia, Rwanda, Tajikistan, Turkmenistan, Ukraine, Uzbekistan, Vietnam, or such other
countries as may be designated by the United States Government), (ii) export to Country Groups D:1
or E:2 (as defined herein) the direct product of the Program or the technology, if such foreign
produced direct product is subject to national security controls as identified on the U.S. Commerce
Control List, or (iii) if the direct product of the technology is a complete plant o r any major
component of a plant, export to Country Groups D:1 or E:2 the direct product of the plant or a major
component thereof, if such foreign produced direct product is subject to national security controls as
identified on the U.S. Commerce Control List or is subject to State Department controls under the
U.S. Munitions List.
5.
UNITED STATES GOVERNMENT RESTRICTED RIGHTS. The enclosed Product (i)
was developed solely at private expense; (ii) contains “restricted computer software” submitted with
restricted rights in accordance with section 52.227-19 (a) through (d) of the Commercial Computer
Software-Restricted Rights Clause and its successors, and (iii) in all respects is proprietary data
belonging to Cabletron and/or its suppliers. For Department of Defense units, the Product is considered
commercial computer software in accordance with DFARS section 227.7202-3 and its successors, and
use, duplication, or disclosure by the Government is subject to restrictions set forth herein.
6.
EXCLUSION OF WARRANTY. Except as may be specifically provided by Cabletron in
writing, Cabletron makes no warranty, expressed or implied, concerning the Program (including its
documentation and media).
CABLETRON DISCLAIMS ALL WARRANTIES, OTHER THAN THOSE SUPPLIED TO
YOU BY CABLETRON IN WRITING, EITHER EXPRESS OR IMPLIED, INCLUDING BUT
NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, WITH RESPECT TO THE PROGRAM, THE ACCOMPANYING
WRITTEN MATERIALS, AND ANY ACCOMPANYING HARDWARE.
7.
NO LIABILITY FOR CONSEQUENTIAL DAMAGES. IN NO EVENT SHALL
CABLETRON OR ITS SUPPLIERS BE LIABLE FOR ANY DAMAGES WHATSOEVER
(INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS, PROFITS,
BUSINESS INTERRUPTION, LOSS OF BUSINESS INFORMATION, SPECIAL, INCIDENTAL,
CONSEQUENTIAL, OR RELIANCE DAMAGES, OR OTHER LOSS) ARISING OUT OF THE
USE OR INABILITY TO USE THIS CABLETRON PRODUCT, EVEN IF CABLETRON HAS
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. BECAUSE SOME STATES DO
NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR
INCIDENTAL DAMAGES, OR IN THE DURATION OR LIMITATION OF IMPLIED
WARRANTIES IN SOME INSTANCES, THE ABOVE LIMITATION AND EXCLUSIONS MAY
NOT APPLY TO YOU.
vi
SWPIM-BRI Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Notice
CABLETRON SYSTEMS LIMITED
PROGRAM LICENSE AGREEMENT
IMPORTANT: THIS LICENSE APPLIES FOR THE USE OF THE PRODUCT IN THE
FOLLOWING GEOGRAPHICAL REGIONS:
EUROPE
MIDDLE EAST
AFRICA
ASIA
AUSTRALIA
PACIFIC RIM
BEFORE OPENING OR UTILIZING THE ENCLOSED PRODUCT,
CAREFULLY READ THIS LICENSE AGREEMENT.
This document is an agreement (“Agreement”) between You, the end user, and Cabletron
Systems Limited (“Cabletron”) that sets forth your rights and obligations with respect to the
Cabletron software program (“Program”) in the package. The Program may be contained in firmware,
chips or other media. UTILIZING THE ENCLOSED PRODUCT, YOU ARE AGREEING TO
BECOME BOUND BY THE TERMS OF THIS AGREEMENT, WHICH INCLUDES THE
LICENSE AND THE LIMITATION OF WARRANTY AND DISCLAIMER OF LIABILITY. IF
YOU DO NOT AGREE TO THE TERMS OF THIS AGREEMENT, RETURN THE UNOPENED
PRODUCT TO CABLETRON OR YOUR DEALER, IF ANY, WITHIN TEN (10) DAYS
FOLLOWING THE DATE OF RECEIPT FOR A FULL REFUND.
IF YOU HAVE ANY QUESTIONS ABOUT THIS AGREEMENT, CONTACT CABLETRON
SYSTEMS +1-603-332-9400. Attn: Legal Department.
1.
LICENSE. You have the right to use only the one (1) copy of the Program provided in this
package subject to the terms and conditions of this License Agreement.
You may not copy, reproduce or transmit any part of the Program except as permitted by the
Copyright Act of the United States or as authorized in writing by Cabletron.
2.
OTHER RESTRICTIONS. You may not reverse engineer, decompile, or disassemble the
Program.
3.
APPLICABLE LAW. This License Agreement shall be governed in accordance with English
law. The English courts shall have exclusive jurisdiction in the event of any disputes.
4.
EXPORT REQUIREMENTS. You understand that Cabletron and its Affiliates are subject to
regulation by agencies of the U.S. Government, including the U.S. Department of Commerce, which
prohibit export or diversion of certain technical products to certain countries, unless a license to export
the product is obtained from the U.S. Government or an exception from obtaining such license may be
relied upon by the exporting party.
If the Program is exported from the United States pursuant to the License Exception CIV under
the U.S. Export Administration Regulations, You agree that You are a civil end user of the Program
and agree that You will use the Program for civil end uses only and not for military purposes.
SWPIM-BRI Installation Guide
vii
Download from Www.Somanuals.com. All Manuals Search And Download.
Notice
If the Program is exported from the United States pursuant to the License Exception TSR under
the U.S. Export Administration Regulations, in addition to the restriction on transfer set forth in
Sections 1 or 2 of this Agreement, You agree not to (i) reexport or release the Program, the source
code for the Program or technology to a national of a country in Country Groups D:1 or E:2 (Albania,
Armenia, Azerbaijan, Belarus, Bulgaria, Cambodia, Cuba, Estonia, Georgia, Iraq, Kazakhstan,
Kyrgyzstan, Laos, Latvia, Libya, Lithuania, Moldova, North Korea, the People’s Republic of China,
Romania, Russia, Rwanda, Tajikistan, Turkmenistan, Ukraine, Uzbekistan, Vietnam, or such other
countries as may be designated by the United States Government), (ii) export to Country Groups D:1
or E:2 (as defined herein) the direct product of the Program or the technology, if such foreign
produced direct product is subject to national security controls as identified on the U.S. Commerce
Control List, or (iii) if the direct product of the technology is a complete plant o r any major
component of a plant, export to Country Groups D:1 or E:2 the direct product of the plant or a major
component thereof, if such foreign produced direct product is subject to national security controls as
identified on the U.S. Commerce Control List or is subject to State Department controls under the
U.S. Munitions List.
5.
UNITED STATES GOVERNMENT RESTRICTED RIGHTS. The enclosed Product (i)
was developed solely at private expense; (ii) contains “restricted computer software” submitted with
restricted rights in accordance with section 52.227-19 (a) through (d) of the Commercial Computer
Software-Restricted Rights Clause and its successors, and (iii) in all respects is proprietary data
belonging to Cabletron and/or its suppliers. For Department of Defense units, the Product is considered
commercial computer software in accordance with DFARS section 227.7202-3 and its successors, and
use, duplication, or disclosure by the Government is subject to restrictions set forth herein.
6.
EXCLUSION OF WARRANTY. Except as may be specifically provided by Cabletron in
writing, Cabletron makes no warranty, expressed or implied, concerning the Program (including its
documentation and media).
CABLETRON DISCLAIMS ALL WARRANTIES, OTHER THAN THOSE SUPPLIED TO
YOU BY CABLETRON IN WRITING, EITHER EXPRESS OR IMPLIED, INCLUDING BUT
NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, WITH RESPECT TO THE PROGRAM, THE ACCOMPANYING
WRITTEN MATERIALS, AND ANY ACCOMPANYING HARDWARE.
7.
NO LIABILITY FOR CONSEQUENTIAL DAMAGES. IN NO EVENT SHALL
CABLETRON OR ITS SUPPLIERS BE LIABLE FOR ANY DAMAGES WHATSOEVER
(INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS, PROFITS,
BUSINESS INTERRUPTION, LOSS OF BUSINESS INFORMATION, SPECIAL, INCIDENTAL,
CONSEQUENTIAL, OR RELIANCE DAMAGES, OR OTHER LOSS) ARISING OUT OF THE
USE OR INABILITY TO USE THIS CABLETRON PRODUCT, EVEN IF CABLETRON HAS
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. BECAUSE SOME STATES DO
NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR
INCIDENTAL DAMAGES, OR IN THE DURATION OR LIMITATION OF IMPLIED
WARRANTIES IN SOME INSTANCES, THE ABOVE LIMITATION AND EXCLUSIONS MAY
NOT APPLY TO YOU.
viii
SWPIM-BRI Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Notice
DECLARATION OF CONFORMITY
Application of Council Directive(s): 89/336/EEC
73/23/EEC
Manufacturer’s Name: Cabletron Systems, Inc.
Manufacturer’s Address: 35 Industrial Way
PO Box 5005
Rochester, NH 03867
European Representative Name: Mr. Jim Sims
European Representative Address: Cabletron Systems Limited
Nexus House, Newbury Business Park
London Road, Newbury
Berkshire RG14 2PZ, England
Conformance to Directive(s)/Product Standards: EC Directive 89/336/EEC
EC Directive 73/23/EEC
EN 55022
EN 55024
EN 60950
EN 60825
Equipment Type/Environment: Networking Equipment, for use in a
Commercial or Light Industrial
Environment.
We the undersigned, hereby declare, under our sole responsibility, that the equipment packaged
with this notice conforms to the above directives.
Manufacturer
Legal Representative in Europe
Mr. Thomas R. Whissel
Mr. Jim Sims
___________________________________
___________________________________
Full Name
Full Name
Compliance Engineering Manager
President - E.M.E.A.
___________________________________
___________________________________
Title
Title
Rochester, NH, USA
Newbury, Berkshire, England
___________________________________
___________________________________
Location
Location
SWPIM-BRI Installation Guide
ix
Download from Www.Somanuals.com. All Manuals Search And Download.
Notice
x
SWPIM-BRI Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
CHAPTER 1
APPENDIX A
SPECIFICATIONS
A.2 Network Interface ........................................................................A-2
A.2.1 Pinout for the S/T-Interface Connector ...........................A-2
A.2.2 Pinout for the U-Interface Connector ..............................A-3
A.3 Environmental Requirements ......................................................A-3
A.4 Regulatory Compliance ...............................................................A-4
APPENDIX B
FCC PART 68 - USER’S INFORMATION
SWPIM-BRI Installation Guide
xi
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
xii
SWPIM-BRI Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
Only qualified personnel should perform installation
procedures.
Welcome to the Cabletron Systems SWPIM-BRI Installation Guide. This
manual gives an introduction to the SWPIM-BRI, lists features and
capabilities, details the cabling pinouts, and explains how to install the
SWPIM-BRI.
The SWPIM-BRI provides S/T-interface (digital) functionality or
U-interface (analog) functionality for a host platform designed to receive
the SWPIM (Sliding WAN Physical Interface Module) architecture.
USING THIS GUIDE
Read through this guide completely to understand the features and
capabilities of the SWPIM-BRI.
A general working knowledge of WAN and Ethernet and IEEE 802.3 data
communications networks and their physical layer components is helpful
before using the SWPIM-BRI.
The term “host platform” will be used to indicate the device or
module, such as the SSR-600 or the HSIM-SSR-600, into
NOTE
which the SWPIM-BRI is installed.
SWPIM-BRI Installation Guide
xiii
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
STRUCTURE OF THIS GUIDE
This guide is organized as follows:
This Introduction provides preliminary information that will aid in using
set up and manage the SWPIM-BRI, gives an overview of the
SWPIM-BRI and its features, and information on how to get help from
Cabletron Systems.
Chapter 1, Installation, provides instructions on how to install the device
into a host platform, and gives the LED indications.
Appendix A, Specifications, contains information on functionality and
operating specifications, connector pinouts for the SWPIM-BRI,
environmental requirements, and physical properties.
Appendix B, FCC Part 68 - User’s Information, explains the FCC rules
for the SWPIM-BRI.
SWPIM-BRI FEATURES
The SWPIM-BRI is installed into any Cabletron Systems product that
supports the SWPIM architecture, such as the SSR-600, or the
HSIM-SSR-600.
The SWPIM-BRI uses a single RJ48 connector supporting the
S/T-interface and the U-interface. There are two different pin assignments
and cables for the two interfaces. Refer to Appendix A for the Cabletron
Systems part numbers and pin assignments for these cables.
The S/T-interface is provided via a four-wire Integrated Services Digital
Network (ISDN) Basic Rate Interface (BRI), while the U-interface is
provided via a two-wire ISDN BRI.
The SWPIM-BRI provides support for the transportation of two 64 Kbps
Bearer (B) channels and one 16 Kbps Data (D) channel for a total of
S/T-interface for terminal equipment (TE) mode or the U-interface for
network termination (NT) mode. Refer to the host platform software
user’s manual for information on how to configure the SWPIM-BRI using
software.
The SWPIM-BRI has two LEDs, to indicate link and status conditions.
Refer to Chapter 1 for more details.
xiv
SWPIM-BRI Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
RELATED MANUALS
The following Cabletron Systems manuals may help the user to set up and
manage the SWPIM-BRI:
SSR-600 Installation Guide
HSIM-SSR-600 Installation Guide
6C105 SmartSwitch 6000 Overview and Setup Guide
Ethernet Technology Guide
Cabling Guide
The manuals referenced above can be obtained on the World Wide Web in
Adobe Acrobat Portable Document Format (PDF) at the following site:
Cabletron Systems applicable software manuals for the SSR-600 and the
HSIM-SSR-600 host platforms (Cabletron Routing Software Manuals):
Bridging Configuration Guide
Event Logging System Message Guide
Network Interface Operations Guide
Routing Protocols Reference Guide
Routing Protocols User's Guide
System Software Guide
ClearVISN Routing Configurator User's Guide
Systems Network Architecture Guide
Quick Reference Guide
DTF (Data Trace Facility) User Guide
SWPIM-BRI Installation Guide
xv
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
DOCUMENT CONVENTIONS
The following conventions may be used in this document:
Note symbol. Calls the reader’s attention to any item of
information that may be of special importance.
NOTE
Tip symbol. Conveys helpful hints concerning procedures or
actions.
TIP
Caution symbol. Contains information essential to avoid
damage to the equipment.
!
CAUTION
Electrical Hazard Warning symbol. Warns against an action
that could result in personal injury or death due to an electrical
hazard.
xvi
SWPIM-BRI Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
GETTING HELP
For additional support related to this device or document, contact
Cabletron Systems using one of the following methods:
World Wide Web
Phone
(603) 332-9400
Internet mail
FTP
anonymous
Login
Password
your email address
To send comments or suggestions concerning this document, contact the
Cabletron Systems Technical Writing Department via the following
Make sure to include the document Part Number in the email message.
Before calling Cabletron Systems, have the following information
ready:
•
•
•
Your Cabletron Systems service contract number
A description of the failure
A description of any action(s) already taken to resolve the problem
(e.g., changing mode switches, rebooting the unit, etc.)
•
The serial and revision numbers of all involved Cabletron Systems
products in the network
•
•
•
A description of your network environment (layout, cable type, etc.)
Network load and frame size at the time of trouble (if known)
The device history (i.e., have you returned the device before, is this a
recurring problem, etc.)
•
Any previous Return Material Authorization (RMA) numbers
SWPIM-BRI Installation Guide
xvii
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
xviii
SWPIM-BRI Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 1
INSTALLATION
Only qualified personnel should install the SWPIM-BRI.
This chapter covers the following items:
•
•
•
•
•
Unpacking the SWPIM-BRI (Section 1.1)
Installing the SWPIM-BRI into the host platform (Section 1.2)
A description of the LANVIEW LED indications (Section 1.3)
Connecting the SWPIM-BRI to the network (Section 1.4)
What to do once the SWPIM-BRI is installed (Section 1.5)
1.1
UNPACKING THE SWPIM-BRI
Use static electricity precautions when handling the SWPIM-BRI.
Failure to observe static safety precautions could cause
damage to the SWPIM-BRI. Follow static safety handling rules
and wear the antistatic wrist strap shipped with the
SWPIM-BRI.
!
CAUTION
1. Open the packing box and remove the SWPIM-BRI.
Do not cut the non-conductive bag to remove the device.
Damage could result from sharp objects contacting the device
or components.
!
CAUTION
2. Attach the antistatic strap (refer to the instructions in the wrist strap
package) before removing the SWPIM-BRI from the antistatic
packaging.
3. Verify that the SWPIM-BRI is undamaged. Refer to Getting Help if
there is any damage to the device. Do not attempt to install the
SWPIM-BRI if it is damaged.
SWPIM-BRI Installation Guide
1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1: Installation
1.2
INSTALLING THE SWPIM-BRI
The SWPIM-BRI can be installed in any available open slot in the host
platform. To install the SWPIM-BRI, proceed as follows:
1. You do not need to power down the host platform to install the
SWPIM-BRI. Check the host platform software manual to see if
desired parameters would be lost from memory upon power down of
the host platform.
2. Remove the blank panel covering the slot in the host platform in which
the SWPIM-BRI will be installed, by prying it off the faceplate.
3. Ensure that the antistatic wrist strap is attached and employed as
recommended.
Observe all precautions to prevent damage from Electrostatic
Discharge (ESD).
!
CAUTION
4. Remove the SWPIM-BRI from the antistatic bag. (Save this bag in the
5. Hold the SWPIM-BRI with the faceplate facing away (right side up)
from the host platform. The 40-pin connector should be facing towards
the empty slot, with the wide part of the connector oriented down. See
Figure 1-1.
6. Locate the rail guides inside the slot in which the SWPIM-BRI will be
installed, as shown in Figure 1-1.
7. Install the SWPIM-BRI in the host platform by aligning the
SWPIM-BRI with the rail guides in the host platform and sliding it in.
Take care that the SWPIM-BRI slides in straight and properly engages
the backplane host connector. Do not force the device.
1-2
SWPIM-BRI Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the SWPIM-BRI
Rail Guides
Host Platform
View of Host Connector End
SWPIM-BRI
Network Connector End
Thumbscrew
LNK
STS
SWPIM-BRI
install
Figure 1-1 Installing the SWPIM-BRI into the Host Platform
8. Fasten the SWPIM-BRI with the thumbscrew.
9. Replace power to the host platform, if necessary. Check to see that the
host platform LED indicators go to their normal configuration. If they
do not, remove the SWPIM-BRI from the host platform and contact
Cabletron Systems.
Do not connect any WAN cables until the SWPIM-BRI has been
configured in software. The phone company can shut down a
line that has an unconfigured connection on it.
!
CAUTION
10. The SWPIM-BRI must be configured before the WAN connection is
made. Once the SWPIM-BRI has been configured, the host platform
must undergo a soft or hard restart in order for the SWPIM-BRI to be
recognized and for traffic to pass. Refer to the appropriate software
manual to configure the SWPIM-BRI.
SWPIM-BRI Installation Guide
1-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1: Installation
1.3
LANVIEW LED INDICATIONS
Refer to Table 1-1 for the link LED indications for the SWPIM-BRI.
Table 1-1 Link LED
Color
Indication
Off
Disabled or Not Configured
Red
Blinking Red
Blinking Amber
Green
Failure
Transmit or Receive Traffic
Port is Active
Refer to Table 1-2 for the status LED indications for the SWPIM-BRI.
Table 1-2 Status LED
Color
Indication
Off
Normal or Disabled
Blinking Amber
Green
Port in Loopback Test Mode
Active Call (B1 and/or B2 is Active)
Failure due to Framing Errors
Blinking Green
1-4
SWPIM-BRI Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to the Network
1.4
CONNECTING TO THE NETWORK
Figure 1-2 depicts a typical configuration for the SWPIM-BRI. The
Cabletron Systems part number for the cable is 9360005-x, where x is the
length of the cable.
WAN Cloud
U-interface
Site 1
NT
SSR-600
SWPIM-BRI
U-interface
Site 2
SSR-600
SWPIM-BRI
S/T-interface
Figure 1-2 Typical Configurations
1.5
COMPLETING THE INSTALLATION
After installing the SWPIM-BRI, the SWPIM-BRI will need to be
configured for the network. Refer to the host platform software
documentation in order to set up and manage the SWPIM-BRI using the
software.
SWPIM-BRI Installation Guide
1-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1: Installation
1-6
SWPIM-BRI Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX A
SPECIFICATIONS
This section describes the environmental specifications and safety and
approval requirements for the SWPIM-BRI. Cabletron Systems reserves
the right to change these specifications at any time without notice.
A.1 PHYSICAL PROPERTIES
Dimensions:
1.91 H x 5.40 W x 19.05 D (cm)
0.75 H x 2.125 W x 7.50 D (in)
Weight (Unit):
90.7 g (3.2 oz)
Nominal current draw on +5V U-interface: 126.5 mA passing traffic
supply from host platform:
S/T-interface: 135 mA passing traffic
MTBF (Predicted):
3,874,392 hours
SWPIM-BRI Installation Guide
A-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A: Specifications
A.2 NETWORK INTERFACE
The SWPIM-BRI uses an RJ48 connector for the network port, with two
separate pinouts, one for the S/T-interface and the other for the
U-interface. The Cabletron Systems Part Number for the cable for both
the S/T-interface and the U-interface is 9360005-x, where x is the length
of the cable.
A.2.1 Pinout for the S/T-Interface Connector
Table A-1 Pinouts for the S/T-Interface Connection
Function
Pin
Polarity
Network
Equipment (NE)
Terminal Equipment (TE)
1
2
3
4
5
6
7
8
No Connection
No Connection
Transmit
No Connection
No Connection
Receive
+
+
-
Receive
Transmit
Receive
Transmit
Transmit
Receive
-
No Connection
No Connection
No Connection
No Connection
The connector for the S/T-interface can be seen in Figure A-1:
1 2 3 4 5 6 7 8
strj45
Figure A-1 S/T-Interface RJ48 Pinout
A-2
SWPIM-BRI Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Environmental Requirements
A.2.2 Pinout for the U-Interface Connector
The network interface pin assignments for the U-interface network
connector are listed in Table A-2.
Table A-2 Pinouts for the U-Interface Connection
Pin
Signal
Direction
1
2
3
4
5
6
No Connection
No Connection
Uline
I/O
I/O
Uline
No Connection
No Connection
The connector for the U-interface is shown in Figure A-2:
1 2 3 4 5 6
urj45
Figure A-2 U-Interface RJ48 Pinout
A.3 ENVIRONMENTAL REQUIREMENTS
Operating Temperature:
Non-operating Temperature:
Operating Humidity:
+5° to +40°C (41° to 104°F)
-30° to +90°C (-22° to 194°F)
5% to 90% (Non-condensing)
SWPIM-BRI Installation Guide
A-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A: Specifications
A.4 REGULATORY COMPLIANCE
This equipment meets the following safety and electromagnetic
compatibility (EMC) requirements:
Safety
UL 1950, CSA C22.2 No. 950, 73/23/EEC,
EN 60950, IEC 950, EN 60825
Electromagnetic
FCC Part 15, CSA C108.8, 89/336/EEC,
Compatibility (EMC) EN 55022, EN 61000-3-2, EN 61000-3-3,
EN 55024, AS/NZS 3548, VCCI V-3
Telecommunications
FCC CFR47 Part 68, CS-03
A-4
SWPIM-BRI Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX B
FCC PART 68 - USER’S INFORMATION
The following instructions are provided to ensure compliance with the
Federal Communications Commission (FCC) Rules, Part 68.
1. This device must only be connected to the ISDN Basic Rate network
behind an FCC Part 68 registered channel service unit. Direct
connection is not allowed.
2. Before connecting your unit, you must inform the telephone company
of the following information:
Port ID
REN/SOC
FIC
USOC
SWPIM-BRI
6.0P
N/A (XD)
N/A (XD)
3. If the unit appears to be malfunctioning, it should be disconnected
from the telephone lines until you learn if your equipment or the
telephone line is the source of the trouble. If your equipment needs
repair, it should not be reconnected until it is repaired.
4. If the telephone company finds that the equipment is exceeding
tolerable parameters, the telephone company can temporarily
disconnect service, although they will attempt to give you advance
notice if possible.
5. Under the FCC Rules, no customer is authorized to repair this
equipment. This restriction applies regardless of whether the
equipment is in or out of warranty.
6. If the telephone company alters their equipment in a manner that will
affect use of this device, they must give you advance warning so as to
give you the opportunity for uninterrupted service. You will be
advised of your right to file a complaint with the FCC.
7. The attached affidavit must be completed by the installer.
SWPIM-BRI Installation Guide
B-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B: FCC Part 68 - User’s Information
8. In the event of equipment malfunction, all repairs should be performed
by our Company or an authorized agent. It is the responsibility of the
users requiring service to report the need for service to our Company
or to one of our authorized agents.
Service can be obtained at Cabletron Systems Technical Support:
Address:
Cabletron Systems, Inc.
35 Industrial Way
Rochester, NH 03867-0505
Phone:
(603) 332-9400
Internet mail:
B-2
SWPIM-BRI Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
AFFIDAVIT FOR THE CONNECTION OF
CUSTOMER EQUIPMENT TO 1.544 MBPS AND/OR
SUBRATE DIGITAL SERVICES
For the work to be performed in the certified territory of
Telco’s name:
State of:
Country of:
I,
, of
(Name of Authorized Representative)
(Customer Name)
,
(Customer’s Address)
(Telephone Number)
being duly sworn, state:
I have responsibility for the operation and maintenance of the terminal
equipment to be connected to _______________________Subrate digital
services. The terminal equipment to be connected complies with Part 68
of the Commission’s rules except for the encoded analog content and
billing protection specifications. With respect to encoded analog content
and billing protection:
•
I attest that all operations associated with the establishment,
maintenance and adjustment of the digital CPE with respect to
encoded analog content and encoded billing information
continuously complies with Part 68 of the FCC’s Rules and
Regulations.
•
•
The digital CPE does not transmit digital signals containing encoded
analog or billing information which is intended to be decoded within
the telecommunications network.
The encoded analog and billing protection is factory set and is not
under the control of the customer.
SWPIM-BRI Installation Guide
B-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B: FCC Part 68 - User’s Information
I attest that the operator(s) maintainer(s) of the digital CPE responsible
for the establishment, maintenance and adjustment of the encoded analog
content and billing information has (have) been trained to perform these
functions by successfully completing one of the following: Check
appropriate one(s).
a. A training course provided by the manufacturer/grantee of the
equipment used to encode analog signals; or
b. A training course provided by the customer or authorized
representative, using training materials and instructions provided
by the manufacturer/grantee of the equipment used to encode
analog signals; or
c. An independent training course (e.g. trade school or technical
institution) recognized by the manufacturer/grantee of the
equipment used to encode analog signals; or
d. In lieu of the proceeding training requirements, the operator(s)
maintainer(s) is (are) under the control of a supervisor trained in
accordance with
above.
I agree to provide
with proper documentation
(Telco’s Name)
to demonstrate compliance with the information as provided in the
proceeding paragraph, if so requested.
(Signature)
(Title)
(Date)
Subscribed and sworn to me this
day of
, 19
.
(Notary Public)
My commission expires:
B-4
SWPIM-BRI Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
|