Bu il t -in Kit Ow n e r ’s Ma n u a l
BHa-1, BHaX-1, BBa-1, Bsa-1, BDa-1 a n D BrB-1 Ki t s
Ou t D O O r Gr il l MO u n t in G s
FO r u s e w it H P3, r3, H3 O r t3 se r ie s Br O il M a s t e r Pr e M iu M Ga s
Gr i l l s
instructiOns Must Be leFt witH tHe Owner FOr Future reFerence aFter installatiOn.
re t a in Ow n e r ’s Ma n u a l F O r Fu t u r e re F e r e n c e .
nO t e : ul ce r t i F i c a t i O n e X t e n D s O n l y t O t H e P r O D u c t , nOt t H e i n s t a l l a t i O n O F t H e P r O D u c t .
GAS-FIRED
Page 1
Download from Www.Somanuals.com. All Manuals Search And Download.
ta B l e O F cO n t e n t s
Congratulations!
You have chosen the finest Built-In Kit for your outdoor cooking pleasure. Please take time to read this
entire manual before assembling your premium Broilmaster Built-In Kit.
Location, Connections, and Safety................................................................................................3 - 4
Enclosure Construction Guidelines .................................................................................................... 5
BHA & BHAX Grill Surround........................................................................................................6 - 10
BBA Tank Caddy........................................................................................................................ 11 - 14
BSA Side Burner Surround........................................................................................................15 - 17
BDA Single Door........................................................................................................................18 - 21
BRB Vent Register Kit ...............................................................................................................22 - 23
Warranty........................................................................................................................................... 24
Your Broilmaster® accessory is identified by model number, serial number, and gas type.
This information is provided on a product identification label located on the accessory. The
grill’s model number, serial number, and gas type must also be provided when contacting
your Broilmaster® dealer. For your convenience, complete this section for future reference
when contacting your dealer.
Model No.
Dealer
Serial No.
Dealer Phone No.
Gas Type: Propane
Natural
Date of Purchase
B101502-1-0311
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
lO c a t iO n , cO n n e c t iO n s , a n D sa F e t y
CAUTION: THE GRILL AND ITS INDIVIDUAL SHUTOFF
Built-In Kit Location
VALVE MUST BE DISCONNECTED FROM THE GAS
SUPPLY PIPING SYSTEM DURING ANY SYSTEM
PRESSURE TESTING AT TEST PRESSURES IN EXCESS
OF 1/2 PSIG.
Built-In Kits are designed for outdoor use ONLY.
This Built-In Kit is designed for use with all P3 and T3 Model
Broilmaster® gas grills and cannot be used with any other
grill or in any other capacity.
Checking for Gas Leaks
Never install or operate your Built-In Kit in any building,
garage, or other enclosed area.
CAUTION: DO NOT USE AN OPEN FLAME TO CHECK
FOR LEAKS. CHECKING FOR LEAKS WITH AN
OPEN FLAME MAY LEAD TO A FIRE OR EXPLOSION,
RESULTING IN PROPERTY DAMAGE OR PERSONAL
INJURY.
For your safety, the Built-In Kit should not be installed or
operated under any combustible materials, such as carports,
covered porches, awnings, or overhangs.
Never install or use your Built-In Kit in or on any recreational
vehicle or boat.
Using the following steps, check for gas leaks during initial
use and each time your Broilmaster® gas grill or side burner
is connected to gas or is connected to a cylinder that has
not been used recently
CAUTION: THE INSTALLATION AND OPERATION OF
THIS BUILT-IN KIT AT CLEARANCES LESS THAN
SPECIFIED BELOW MAY LEAD TO THE POSSIBILITY OF
FIRE, PROPERTY DAMAGE, OR PERSONAL INJURY.
1. Using dish washing detergent and water, make a soapy
solution.
A minimum clearance of twenty-four (24”) inches is required
from all sides of the island to any combustible material.
2. Turn OFF the knob on both the grill and side burner’s
control panel.
Examples of combustible materials are patio furniture,
fences, or the outside of your home.
3. Turn ON the gas at the supply. A hissing sound indicates
a leak. Turn OFF the gas and repair all leaks.
Theareasurroundingthebuilt-inkitshouldbecleartoensure
proper ventilation. Do not obstruct the flow of combustion
and ventilation air in any way. The ventilation openings on
the enclosure must also remain free and clear of debris.
4. If no hissing occurs, apply the soapy solution to all gas
connections.
5. Look for bubbles. Bubbles indicate a leak.
6. If there are bubbles, turn OFF the gas and repair all
WARNING: DO NOT INSTALL OR OPERATE THIS BUILT-
IN KIT WHERE GASOLINE OR OTHER FLAMMABLE
MATERIALS ARE USED OR STORED. FAILURE TO
COMPLY WITH THIS WARNING COULD RESULT IN
EXPLOSION OR FIRE CAUSING PROPERTY DAMAGE
OR PERSONAL INJURY.
leaks.
7. Turn the gas ON and repeat the above procedure until
all leaks are repaired.
Connection Requirements
CAUTION: NEVER USE LIQUID PROPANE GAS IN A
GRILL DESIGNED FOR NATURAL GAS, OR NATURAL
GAS IN A GRILL DESIGNED FOR LIQUID PROPANE
GAS. QUESTIONS REGARDING DIFFERENT TYPES OF
GASES SHOULD BE DIRECTED TO YOUR LOCAL GAS
COMPANY.
Installation must conform to local codes or, in the absence
of local codes, with the National Fuel Gas Code, ANSI
Z223.1. In Canada, installation shall be in accordance with
CAN/CGA-B149.2 Propane Installation Code, or CAN/
CGA-B149.1 Natural Gas Installation Code, and local
codes where applicable. Consult your local gas company or
Propane gas dealer for code regulations and recommended
procedures.
Broilmaster® gas grills and side burners are NOT equipped
with pressure regulators. Your Nat. gas grill operates at a
manifold pressure of seven (7”) inches water column.
Page 4
B101502-1-0311
Download from Www.Somanuals.com. All Manuals Search And Download.
en c l O s u r e cO n s t r u c t iO n Gu iD e l in e s
Enclosure must be construction from non-combustible material.
If tile is used on the top surface of your enclosure, it may be necessary to enlarge openings at the top edges to allow the
frame pieces of the BHA and BSA to mount flush against the enclosure.
Screws for enclosure mounting have been supplied. Installer must measure for thickness and use appropriate hardware for
installation. If the enclosure is constructed from masonry materials, it may be necessary to substitute appropriate screws
and fasteners.
This diagram is only a basic plan for constructing an enclosure for your built-in kit. All construction and installation should
comply with all local building codes and requirements.
MINIMUM REQUIREMENTS
Key Dimension in Inches
Key Dimension in Inches
A
B
C
D
E
F
38” (Minimum)
16” (Minimum)
28” (Minimum)
26 13/16”
O
P
Q
R
S
T
14” (Single) - 27 1/2” (Double)
15 7/8” (Single) - 9 1/8” (Double)
13 15/16”
5” (Minimum)
24 13/16”
24 3/4”
10”
10 11/32”
12 3/16”
G
H
J
6” (Minimum)
15 3/8”
U
V
W
X
Y
Z
2 1/4”
14”
2 3/4”
K
L
19 13/16”
9”
2 1/2”
1 13/16”
14 3/8”
M
N
1 11/16”
22 3/8” (Single) - 15 5/8” (Double)
B101502-1-0311
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
BHa-1 & BHaX-1 Gr il l su r r O u n D Ki t s
in s t a l l a t i O n in s t r u c t iO n s
nOtice: re F e r t O t H e Bu il t -in Kit en c l O s u r e cO n s t r u c t iO n Gu iD e O n P a G e 5 F O r P r O P e r
D iM e n s iO n s O F t H e O P e n in G F O r t H e BHa-1 Gr il l su r r O u n D Kit
Page 6
B101502-1-0311
Download from Www.Somanuals.com. All Manuals Search And Download.
BHa-1 & BHaX-1 Gr il l su r r O u n D eX P l O D e D vie w & Pa r t s lis t
All repair part orders should be placed through your local Broilmaster® dealer. To locate a dealer in your area, contact
Broilmaster Customer Service at 800-851-3153 • www.broilmaster.com. To ensure prompt and accurate service, please
provide the following information when placing a repair part order: Model Number, Part Name, Part Number, and Quantity
of parts needed.
1
2
3
5
8
4
9
6
7
Index No. Part No. Description
Quantity
1
2
3
4
4
5
6
7
7
8
9
R2737
10 x 1/2 Phillips Head Screw
1
1
1
1
1
8
1
1
1
4
2
B101206 Flexline Bracket
B101205 Flexline
B101200 BHA Assembly
B101529 BHAX Assembly
B101022 8 x 3/4” Hex Head Screw
B101178 Grease Tray
B101204 Control Housing Assembly - BHA
B101530 Control Housing Assembly - BHAX
B100113 1/4 - 20 x 1 1/4 Screw (use only with T3/P3 Sereis grill heads)
B060337 Grease Cup
Verify that all parts listed on the exploded view of this manual have been included in this
Built-In Kit before beginning installation.
Caution: Use caution when handling parts, as they may contain sharp edges.
Work gloves are recommended to prevent injury.
Tools Required: Phillips Head Screw Driver (An electric screw driver or drill is recommended to ease installation)
B101502-1-0311
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
BHa & BHaX as s e M B l y
Attention: If applicable, remove protective film from parts
before installation.
3. Place the grease tray into BHA surround by sliding it
under the bracket. See Figure 3.
1. Remove the surround from the shipping box and place
the BHA surround into position in the constructed
enclosure. See Figure 1.
BHA ASSEMBLY
GREASE TRAY
Figure 3
4. Place the control housing assembly into BHA surround
and secure it to the BHA surround. See Figure 4.
BHA ASSEMBLY
CONTROL HOUSING
ASSEMBLY
Figure 1
2. Secure the BHA surround to the enclosure using eight
(8) 8 x 3/4” Hex Head Screw screws. See Figure 2.
Note: If you have a masonry structure you may need to
substitute for the appropriate masonry fasteners.
Figure 4
5. Attach the flex line to the bottom of the BHA surround
using the flex line bracket and screw. See Figure 5.
Figure 2
Figure 5
Page 8
B101502-1-0311
Download from Www.Somanuals.com. All Manuals Search And Download.
BHa & BHaX as s e M B l y
8. If you are using natural gas or a fixed fuel propane
gas supply a 3/8 NPT flare is provided for LP tank.
Check for gas leaks as discussed in the “Checking for
Gas Leaks” Section of this manual on page 4.
6. After insuring that all the contents are removed from the
inside of the grill, install the grill in the BHA surround by
slightly tilting the grill forward and placing it on the top
of the support bracket. See Figure 6.
9. Open control housing and connect flex line to the main
valve, then close the control housing door. Figure 8.
Figure 6
7. Mount the grill to the BHA surround using four 1/4-20 x
1 1/4” screws. See Figure 7.
Figure 8
Refer to your Grill Head Installation Instructions to com-
plete installation of your Broilmaster grill.
Figure 7
B101502-1-0311
Page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
BHa & BHaX as s e M B l y
10. Install each of the four vent covers (BRB Vent Register
Kit) into the Built-In Kit Enclosure using two #8 x 3/4”
screws. See Figure 9.
Alternate Match Lighting Instructions
1. Turn the burner control knobs clockwise to the OFF
position.
2. Turn ON gas at the source.
3. Open the grill lid.
4. Open the BHA access door. Locate the Ignitor Rod,
which is permanently attached to the inside of the
Bottom Shelf.
5. Insert an unlit match into the coiled end of the ignitor
rod. Light the match.
6. Insert the ignitor rod inside the access door and through
the front left air hole located on the bottom of the grill.
Position the match near the rear left corner of the burner.
See Figure 10.
7. Turn the left burner control knob counterclockwise to
HI.
8. If the burner fails to light after 5 seconds, turn the
burner control knob OFF for five minutes then repeat
the procedure.
9. If the burner continues not to light, turn OFF all gas and
refer to the troubleshooting section of your grill Owner’s
Manual.
Figure 9
Figure 10
Page 10
B101502-1-0311
Download from Www.Somanuals.com. All Manuals Search And Download.
BBA-1 TANK CADDY
INSTALLATION INSTRUCTIONS
nOtice: re F e r t O t H e Bu il t -in Kit en c l O s u r e cO n s t r u c t iO n Gu iD e F O r P r O P e r D iM e n s iO n s
O F t H e O P e n in G F O r t H e BBa-1 ta n K ca D D y .
THE BBA TANK CADDY IS DESIGNED TO BE USED AS EITHER AN ENCLOSURE FOR A PORTABLE
PROPANE TANK OR A GARBAGE RECEPTACLE. PLEASE REFER TO THE APPROPRIATE SECTIONS OF THIS
MANUAL FOR PROPANE TANK REQUIREMENTS, CONNECTIONS, AND SAFETY.
B101502-1-0311
Page 11
Download from Www.Somanuals.com. All Manuals Search And Download.
BBa ta n K ca D D y eX P l O D e D vie w a n D Pa r t s lis t
All repair part orders should be placed through your local Broilmaster® dealer. To locate a dealer in your area,
contact Broilmaster® Customer Service at 800-851-3153 • WWW.broilmaster.com. To ensure prompt and accurate
service, please provide the following information when placing a repair part order: Model number of your Single
Door, Part Name, Part Number, and Quantity of parts needed.
1
3
2
PARTS LIST
Index No.
Part No.
B101180
B101181
B101022
Description
Quantity
1
2
3
BBA Frame Assembly
BBA Door Assembly
8 x 3/4” Hex Head Screw
1
1
8
VERIFY THAT ALL PARTS LISTED IN THE EXPLODED VIEW ON THIS PAGE HAVE BEEN INCLUDED IN
THIS BUILT-IN KIT BEFORE BEGINNING THIS INSTALLATION.
CAUTION: USE CAUTION WHEN HANDLING PARTS, AS THEY MAY CONTAIN SHARP EDGES.
WORK GLOVES ARE RECOMMENDED TO PREVENT INJURY.
Page 12
B101502-1-0311
Download from Www.Somanuals.com. All Manuals Search And Download.
BBA TANK CADDY INSTALLATION
Recommended Tools: Phillips Screw Driver or an
electric screw driver.
2
While positioned on its side, place the BBA Door
Assembly into the BBA Frame opening. FIGURE 2.
1
MakesureBBATankCaddyopeningdimensionsmatch
those in FIGURE 1. Place the BBA Frame Assembly in
the Built-In Enclosure.
BBA FRAME ASSEMBLY
Secure the BBA Frame to the Enclosure with eight (8)
8 x 3/4” Hex Head screws as shown in FIGURE 1
Note: The hinge pins on the BBA Frame will be
located near the bottom of the Built-In Enclosure when
properly installed. Also See the proper dimensions of
the opening in FIGURE 1
BBA DOOR ASSEMBLY
FIGURE 2
13 15/16”
3
Once located inside the BBA Frame, rotate the BBA
Door to the upright position.
”
2413/16
FIGURE 3.
BUILD IN
ENCLOSURE
BBA FRAME
ASSEMBLY
SCREWS (8)
FIGURE 3
FIGURE 1
B101502-1-0311
Page 13
Download from Www.Somanuals.com. All Manuals Search And Download.
BBA TANK CADDY INSTALLATION
less than a total free area of 10 square inches
4
(64.5 cm2).
Lower the BBA Door Assembly onto the two hinge pins
inside the lower left and right sides of the BBA Frame.
FIGURE 4 .
2. Ventilation opening(s) shall be provided at floor
level and shall have a total free area of not less
than 1/2 square inch per pound (7.1 cm2/kg) of
stored fuel capacity and not less than a total free
area of 10 square inches (64.5 cm2). If ventilation
openings at floor level are in a side wall, there
shall be at least two openings. The bottom of the
openings shall be at floor level and the upper edge
no more than 5 inches (127 mm) above the floor.
The openings shall be equally sized, spaced at
180 degrees (3.14 rad) and unobstructed.
3. Every opening shall have minimum dimensions so
as to permit the entrance of an 1/8 inch (3.2 mm)
diameter rod.
The cylinder valve shall be readily accessible for hand
operation. A door on the enclosure to gain access to
the cylinder valves is acceptable, provided it is non-
locking and can be opened without the use of tools.
HINGE
PIN
The enclosure for the LP gas cylinder shall isolate
the cylinder from the burner compartment to provide
shielding from radiation, a flame barrier, and protection
from foreign material, such as hot drippings.
FIGURE 4
ENCLOSURE REQUIREMENTS
There shall be a minimum clearance of 2 inches
(50.8 mm) between the floor of the LP gas cylinder
enclosure and the ground.
The enclosure design must be constructed to allow
only storage of the LP cylinder in use thus preventing
storage of a second cylinder. Tank caddy must be
provided for use in the enclosure when employing the
propane self-contained system so as to prevent the
lateral movement of the propane tank cylinder from its
enclosure.
The design of the outdoor cooking gas appliance shall
be such that the LP gas cylinder can be connected,
disconnected and the connections inspected and
tested outside the cylinder enclosure; and those
connections which could be disturbed when installing
the cylinder in the enclosure can be leak tested inside
the enclosure.
An enclosure for a LP gas cylinder shall be ventilated
by openings at the level of the cylinder valve and at floor
level. The effectiveness of openings(s) for purposes of
ventilation shall be determined with the LP gas supply
cylinder in place. This shall be accompanied by one
of the following: enclosure with one side completely
open; or enclosure having four sides, a top and a
bottom. Refer to the Built-In Kit enclosure construction
guide for proper dimensions of the opening for the
BBA-1 Tank Caddy.
1. At least two ventilation openings at cylinder valve
level shall be provided in the side wall, equally
sized, spaced at 180 degrees (3.14 rad), and
unobstructed. Each opening shall have a total free
area of not less than 1/2 square inch per pound
(7.1 cm2/kg) of stored fuel capacity and not
Page 14
B101502-1-0311
Download from Www.Somanuals.com. All Manuals Search And Download.
BSA-1 SIDE BURNEr surrOunD Kit
INSTALLATION INSTRUCTIONS
nOtice: re F e r t O t H e Bu il t -in Kit en c l O s u r e cO n s t r u c t iO n Gu iD e F O r P r O P e r D iM e n s iO n s
O F t H e O P e n in G F O r t H e Bsa-1 siD e Bu r n e r su r r O u n D
THE BSA SIDE BURNER SURROUND IS DESIGNED TO BE USED WITH THE DPASBC NATURAL and
PROPANE GAS SIDE BURNER ONLY. DO NOT USE ANY OTHER SIDE BURNER WITH THE BSA SIDE
BURNER SURROUND.
B101502-1-0311
Page 15
Download from Www.Somanuals.com. All Manuals Search And Download.
Bsa siD e Bu r n e r su r r O u n D eX P l O D e D vie w a n D Pa r t s lis t
All repair part orders should be placed through your local Broilmaster® dealer. To locate a dealer in your area,
contact Broilmaster® Customer Service at 800-851-3153 • www.broilmaster.com. To ensure prompt and accurate
service, please provide the following information when placing a repair part order: Model number of your Side
Burner, Part Name, Part Number, and Quantity of parts needed.
3
2
1
PARTS LIST
Index No.
Part No.
B101164
B100130
Description
Quantity
1
2
Side Burner Liner
1
2
10-24 x 3/8 Phillips Head Screw
(for use only with DPASBC Side Burner)
8 x 3/4” Hex Head Screw
3
B101022
4
VERIFY THAT ALL PARTS LISTED IN THE EXPLODED VIEW ON THIS PAGE HAVE BEEN INCLUDED IN
THIS BUILT-IN KIT BEFORE BEGINNING THIS INSTALLATION.
CAUTION: USE CAUTION WHEN HANDLING PARTS, AS THEY MAY CONTAIN SHARP EDGES.
WORK GLOVES ARE RECOMMENDED TO PREVENT INJURY.
Page 16
B101502-1-0311
Download from Www.Somanuals.com. All Manuals Search And Download.
Bsa in s t a l l a t i O n
Recommended Tools: Phillips Screw Driver or an
electric screw driver.
2
Attach one end of the Side Burner Hose to your
Broilmaster® DPASBC Side Burner. The remaining
end of the hose should be routed down through the
bottom of the BSA Liner. Place the side burner into
the BSA Liner and slide it completely to the rear of the
Liner. FIGURE 3.
1
Make sure BSA Side Burner Surround opening
dimensions match those in FIGURE 1. Place the BSA
Liner into the Enclosure and check for proper hole
alignment. Secure the BSA Liner to the Enclosure with
four (4) 8 x 3/4” Hex Head screws. You should use the
inside holes located on the inside of the BSA Liner.
FIGURE 2.
12 3/16”
14 3/8”
FIGURE 1
FIGURE 3
3
BSA LINER
SCREWS (4)
Secure the DPASBC Side Burner to the BSA Liner
with two 10-24 x 3/8 PH PN screws to the inside holes
located on the side of the Side Burner. FIGURE 4.
Note: If you have already routed your Side Burner
Hose make sure it is projecting up through the bottom
of the BSA Liner.
ENCLOSURE
#10-24 x 3/8 PH PN
SCREWS (2)
FIGURE 2
FIGURE 4
B101502-1-0311
Page 17
Download from Www.Somanuals.com. All Manuals Search And Download.
BDa-1 sinGle/DOuBle DOOr Kit
INSTALLATION INSTRUCTIONS
nOtice: re F e r t O t H e Bu il t -in Kit en c l O s u r e cO n s t r u c t iO n Gu iD e F O r P r O P e r D iM e n s iO n s
O F t H e O P e n in G F O r t H e BDa-1 sin G l e /DO u B l e DO O r Kit
THE BDA SINGLE DOOR KIT IS DESIGNED TO BE USED IN AN ISLAND OR OTHER APPLICATION.
Page 18
B101502-1-0311
Download from Www.Somanuals.com. All Manuals Search And Download.
BDa sin G l e DO O r eX P l O D e D vie w a n D Pa r t s lis t
All repair part orders should be placed through your local Broilmaster® dealer. To locate a dealer in your area,
contact Broilmaster® Customer Service at 800-851-3153 • www.broilmaster.com. To ensure prompt and accurate
service, please provide the following information when placing a repair part order: Model number of your Single
Door, Part Name, Part Number, and Quantity of parts needed.
1
2
3
4
PARTS LIST
Index No.
Part No.
B101191
B101022
B101192
B101153
Description
Quantity
1
2
3
4
BDA Door Frame
1
8
1
1
8 x 3/4” Hex Head Screw
BDA Door
BDA Door Bracket (used on double door installation
only)
VERIFY THAT ALL PARTS LISTED IN THE EXPLODED VIEW ON THIS PAGE HAVE BEEN INCLUDED IN
THIS BUILT-IN KIT BEFORE BEGINNING THIS INSTALLATION.
CAUTION: USE CAUTION WHEN HANDLING PARTS, AS THEY MAY CONTAIN SHARP EDGES.
WORK GLOVES ARE RECOMMENDED TO PREVENT INJURY.
B101502-1-0311
Page 19
Download from Www.Somanuals.com. All Manuals Search And Download.
BDa sin G l e DO O r in s t a l l a t i O n
Attention: If Applicable, remove protective film from parts before installation.
Recommended Tools: Phillips Screw Driver or an
electric screw driver.
1
The BDA Single Door will be fully assembled when it is
shipped out. Remove door from frame by depressing
one of the spring loaded pins and set aside.
FIGURE 1.
FIGURE 3
3
Secure the BDADoor to the door frame by inserting the
spring loaded pin in the bottom frame hole. Locate the
upper hole in the frame then push on the spring loaded
pin on the door and insert the door in the frame.
Figure 4.
FIGURE 1
2
Make sure BDA Single Door opening dimensions
match those in FIGURE 2. Place the Frame into the
opening and check for proper hole alignment. Secure
the Frame to the grill enclosure with eight (8) 8 x 3/4”
Hex Head Screw screws. FIGURE 3.
Make sure the Door is Aligned and Secured prop-
erly by opening and closing door
14”
19 13/16”
FIGURE 2
FIGURE 4
Page 20
B101502-1-0311
Download from Www.Somanuals.com. All Manuals Search And Download.
BDA DOUBLE DOOR INSTALLATION
NOTE: You will need two BDA door kits for this installation.
3
1
Make sure BDA Double Door opening dimensions
Remove doors from frames by depressing one of the
spring loaded pins on each door and set them aside.
Disassemble frame by removing the two screws and
door pin from both door frames as shown in FIGURE
5.
match those in FIGURE 7. Place the Frame into
the opening and check for proper hole alignment.
Secure the Frame to the enclosure with 2 screws.
FIGURE 7.
Secure the Doors to the door frame by inserting the
spring loaded pins in the bottom frame holes. Locate
the upper hole in the BDAframe and push on the spring
loaded pin on the door and insert it into the frame.
Figure 4.
Make sure the Door is Aligned and Secured prop-
erly by opening and closing door.
27 ½”
19 13/16”
FIGURE 5
2
Use the door brackets included in the hardware
packages to combine the frames. Use the screws from
the single door to attach the bracket, and place the
door pin in position. FIGURE 6
FIGURE 7
FIGURE 6
B101502-1-0311
Page 21
Download from Www.Somanuals.com. All Manuals Search And Download.
BRB-1 VENT REGISTER KIT
INSTALLATION INSTRUCTIONS
nOtice: re F e r t O t H e Bu il t -in Kit en c l O s u r e cO n s t r u c t iO n Gu iD e F O r P r O P e r D iM e n s iO n s
O F t H e O P e n in G F O r t H e BrB-1 ve n t re G is t e r Kit
The BRB Vent Register Kit is designed to be used with any enclosure that has an
LP tank.
Page 22
B101502-1-0311
Download from Www.Somanuals.com. All Manuals Search And Download.
BrB ve n t re G is t e r cO v e r Kit eX P l O D e D vie w a n D Pa r t s lis t
All repair part orders should be placed through your local Broilmaster® dealer. To locate a dealer in your area,
contact Broilmaster® Customer Service at 800-851-3153 • www.broilmaster.com. To ensure prompt and accurate
service, please provide the following information when placing a repair part order: Model number of your Side
Burner, Part Name, Part Number, and Quantity of parts needed.
1
2
PARTS LIST
Index Part No.
No.
Description
Quantity
1
2
B071712 Vent Register
2
B101022 8 x 3/4” Hex Head Screw
4
Two BRB Vent Register kits are needed for proper installation.
Install two vent registers into each side of the Built-In Kit Enclosure using two screws per vent register.
B101502-1-0311
Page 23
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY
Manufactured in U.S.A. by Broilmaster, a Division of Empire Comfort Systems, Inc.,
P.O. Box 529, Belleville, Illinois 62222.
WHAT IS COVERED AND FOR HOW LONG
From the date these kits are purchased for use, Broilmaster will make available, at our
factory, a free replacement for any defective part covered by this warranty on the fol-
lowing basis:
LIMITED LIFETIME WARRANTY
Stainless Components for Built-In Series (BHA, BBA, BSA, BDA, & BRB)
Page 24
B101502-1-0311
Download from Www.Somanuals.com. All Manuals Search And Download.
nO t e s
B101502-1-0311
Page 25
Download from Www.Somanuals.com. All Manuals Search And Download.
nO t e s
Page 26
B101502-1-0311
Download from Www.Somanuals.com. All Manuals Search And Download.
nO t e s
B101502-1-0311
Page 27
Download from Www.Somanuals.com. All Manuals Search And Download.
THE MOST DURABLE GRILL
KNOWN TO MAN
BROILMASTER®
A Division of Empire Comfort Systems, Inc.
918 Freeburg Ave.
Belleville, Illinois 62220
Phone: 1-800-851-3153
FAX: 1-800-443-8648
VISIT OUR WEB SITE AT WWW.broilmaster.com
Page 28
B101502-1-0311
Download from Www.Somanuals.com. All Manuals Search And Download.
|