USER MANUAL
HEPA Filtration and
Fresh Air
Ventilation*
GSVH1K
HEPA Filtration,
HEPA
Fresh Air and
Heat Recovery
Ventilation*
Filtration*
GSFH1K
VB0061
HEPA Filtration,
Fresh Air and
Energy Recovery
Ventilation*
GSHH3K
*Patents pending
GSEH3K
RESIDENTIAL USE ONLY.
INSTALLER: LEAVE THIS MANUAL WITH CONSUMER.
REGISTER YOUR PRODUCT ON LINE AT:
05690 rev. 5
Broan-NuTone LLC
99043224
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
1.0
2.0
ABOUT THESE UNITS .................................................4
CONTROLS............................................................5-8
2.1 Main Switch.....................................................................5
2.2 Operating ACCGSC1 Controller .....................................5
2.3 Operating 40425 Controller .........................................6-8
3.0
MAINTENANCE.....................................................9-12
3.1 Semi-annual Maintenance .........................................9-11
3.2 Annual Maintenance .....................................................11
3.3 Optional Alpine/pine Filter.............................................12
TROUBLESHOOTING.................................................13
WARRANTY ............................................................14
4.0
5.0
- 3 -
Download from Www.Somanuals.com. All Manuals Search And Download.
1. ABOUT THESE UNITS
!
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO
PERSON(S) OBSERVE THE FOLLOWING:
1. This unit is intented for residential installation only.
2. Installation must be done in accordance with all applicable codes and
standards, including fire-rated construction codes and standards.
3. This unit is not designed to provide combustion and/or dilution air for
fuel-burning appliances.
4. Do not install in a cooking area or connect directly to an appliance.
5. Before replacing filters, servicing or cleaning unit, disconnect the power
cord from the electrical outlet.
6. When cutting or drilling into the wall or ceiling, do not damage electrical wiring
or other hidden utilities.
7. Do not use this unit with any solid-state speed control device other than
wall controls ACCGSC1 or 40425, provided with the unit.
8. This unit must be grounded. The power supply cord has a 3-prong grounding
plug for your personal safety. It must be plugged into a mating 3-prong
grounding receptacle, grounded in accordance with the national electrical code
and local codes and ordinances. Do not remove the ground prong. Do not
use an extension cord.
9. This unit must be installed in a weatherized location out of direct sunlight
and protected from the elements.
10. Use this unit only in the manner intended by the manufacturer. If you
have questions, contact the manufacturer at the address or telephone number
listed in this document.
11. When cleaning the unit, it is recommended to wear safety glasses and gloves.
CAUTION
1. For general ventilating use only. Do not use to exhaust hazardous or explosive
materials and vapors.
2. Intended for residential installation in accordance with the requirements of
NFPA 90B.
3. For GSVH1K, GSHH3K and GSEH3K units only: Be sure to duct air outside.
Do not intake / exhaust air into spaces within walls or ceiling or into attics,
crawl spaces, or garage.
4. Do not run any air ducts directly above or closer than 2 ft (0.61 m) to any furnace
or its supply plenum, boiler, or other heat producing appliance. If a duct has
to be connected to the furnace return plenum, it must be connected not
closer than 2 ft (0.61 m) from this plenum connection to the furnace.
5. The ductwork is intended to be installed in compliance with all local and
national codes that are applicable.
6. To avoid prematurate clogged filters, turn OFF the unit during construction
or renovation.
7. At least once in a year, the unit mechanical and electronic parts should be
inspected by qualified service personnel.
8. Please read the unit specification label on the product for further information
and requirements.
- 4 -
Download from Www.Somanuals.com. All Manuals Search And Download.
2. CONTROLS
2.1 MAIN SWITCH
All units are equipped with a 3-position main switch, located on the front panel. The
unit is intented for use with a wall controller (provided, see below). The main switch
is to remain in either the “OFF” or “Normal/Remote” modes ONLY.The “Normal/Remote”
mode allows the homeowner to operate the product from the wall controller (supplied
with the unit), typically mounted near a thermostat or other convenient location.
NORMAL/REMOTE:
UNIT IS OPERATING ON
LOW SPEED. THIS IS THE
CORRECT POSITION
WHEN THE WALL
OFF:
UNIT IS OFF AND
DOOR IS
CONTROLLER IS USED.
UNLOCKED.
BOOST:
UNIT IS OPERATING
ON HIGH SPEED.
VC0053
2.2 OPERATING ACCGSC1 CONTROLLER
2.2.1 ACCGSC1 CONTROLLER DESCRIPTION
POWER INDICATOR:
HIGH:
LIGHTS UP WHEN SLIDE
UNIT IS OPERATING AT
ITS HIGH SPEED.
SWITCH IS IN THE HIGH OR
LOW POSITION.
Power
FILTER MAINTENANCE
INDICATOR:
FLASHES EVERY MINUTE TO
High
Low:
Low
UNIT IS OPERATING AT
ITS LOW SPEED.
OFF
INDICATE IT IS ON DUTY.
FLASHES EVERY SECOND
Filter Maintenance
Reset Filter
WHEN IT IS TIME TO
OFF:
UNIT IS OFF.
REPLACE PREFILTER.
LED STAYS LIT WHEN IT IS
VC0059
TIME TO REPLACE FILTER
RESET FILTER HOLE:
AND PREFILTER.
ONCE THE MAINTENANCE DONE, RESET THE FILTER
MAINTENANCE INDICATOR BY CAREFULLY INSERTING A SMALL
ROD (E.G.: PAPER CLIP) IN THE RESET FILTER HOLE,
FOR 1 SECOND. THE FILTER MAINTENANCE INDICATOR
WILL TURN OFF. REFER TO THE FILTER MAINTENANCE
RECOMMENDATIONS IN SECTION 3.
2.2.2 USING ACCGSC1 CONTROLLER
• OFF: To stop the unit, slide the button on this position.
• LOW: For a day-to-day usage, slide the button on this position.
The unit then will operate on low speed, providing 70 cfm.
• HIGH: For a high speed operation, slide the button on this position.
Generally used when more ventilation is required, such as parties,
smokers, or for a 6-bedroom house. This mode provides 105 cfm.
- 5 -
Download from Www.Somanuals.com. All Manuals Search And Download.
2. CONTROLS (CONT’D)
2.3 OPERATING 40425 CONTROLLER
The included wall control 40425 is intented for GSHH3K and GSEH3K units only.
The wall control is in OFF mode when power is applied for the first time.The mode
does not change following a power failure.
2.3.1 40425 CONTROLLER DESCRIPTION
FILTER AND PREFILTER
MAINTENANCE LED.
FLASHES WHEN IT IS
TIME TO REPLACE
PREFILTER AND WASH
CORE FILTERS.
ILLUMINATES IN
ALL MODES
EXCEPT OFF
MODE.
40425
SEE SEMI-ANNUAL
MAINTENANCE IN
SECTION 3.1.
LIGHTS UP WHEN IT IS
TIME TO REPLACE FILTER
AND PREFILTER AND
WASH CORE FILTERS.
SEE ANNUAL
• PRESS EITHER
BUTTON TO CHANGE
CONFIGURATION SETTING
(SEE SECTION 2.3.3).
• PRESS BOTH
BUTTONS TO RESET
THE FILTER COUNTER OR
PREFILTER COUNTER.
MAINTENANCE
SECTION 3.2.
VC0098
PRESS THIS BUTTON TO
ACCESS CONFIGURATION
PARAMETERS
PRESS THIS BUTTON TO
SWITCH MODE
(SEE SECTION 2.3.3).
(SEE SECTION 2.3.2).
2.3.2 USING 40425 CONTROLLER
The wall controller 40425 provides 5 operation modes. Press the Mode button to
select the desired mode.
NORMAL MODE (MIN)
BOOST MODE (MAX)
The unit exchanges air
at normal speed.
The unit exchanges air
at high speed.
The outdoor
The outdoor
temperature* is displayed.
temperature* is displayed.
* The outdoor temperature reading is taken from the unit FRESH AIR FROM
OUTSIDE port; due to the lenght of the insulated duct, the reading is slightly
different from the real outside temperature.
- 6 -
Download from Www.Somanuals.com. All Manuals Search And Download.
2. CONTROLS (CONT’D)
2.3.2 USING 40425 CONTROLLER (CONT’D)
RECIRCULATION MODE (RE-CIRC)
OFF MODE
The unit recirculates air. However,
The unit is off.
every hour, the unit exchanges
air for 6 minutes so that
The outdoor temperature*
is not displayed.
it can obtain a reading
of the outdoor temperature*.
AUTOMATIC MODE (AUTO)
Off in
Auto mode
Air recirculation
in Auto mode
Air exchange in
Auto mode
The unit operates on a 60-minute cycle.
For the first 40 minutes, the unit recirculates
air or is off (See configuration parameter 2
in Section 2.3.3). For the last 20 minutes,
it exchanges air. However, if the outdoor
temperature* is too high or too low (see
configuration parameters 3 and 4 in
Section 2.3.3), the unit recirculates air
during the last 20 minutes.
* The outdoor temperature reading is taken from the unit FRESH AIR FROM
OUTSIDE port; due to the lenght of the insulated duct, the reading is slightly
different from the real outside temperature.
- 7 -
Download from Www.Somanuals.com. All Manuals Search And Download.
2. CONTROLS (CONT’D)
2.3.3 40425 WALL CONTROLLER CONFIGURATION
See the configuration table below for the list of configuration parameters.
Press the Menu button for 3 seconds to enter or exit the configuration menu.
NOTE: The wall control automatically saves any changes and exits the
configuration menu if no button is pressed within the next 60 seconds.
Press the Menu button briefly to advance to the next parameter (menu number).
Press the
or
button to change the parameter setting.
CONFIGURATION TABLE
MENU
DEFAULT
SETTING
PARAMETER
NUMBER
OPTIONS
°C / °F
DESCRIPTION
TEMPERATURE
FORMAT
1
°C
SELECTS BETWEEN °C AND °F DISPLAY.
SELECTS BETWEEN AIR RECIRCULATION
AUTO MODE
OPERATION
2
RE / OF
RE (RE) AND OFF (OF).
SEE SECTION 2.3.2.
AUTO MODE
PREVENTS AIR EXCHANGE IN AUTO
LOW
-30°C TO 0°C (-25°C) MODE IF THE OUTDOOR TEMPERATURE
3
TEMPERATURE (-22°F TO 32°F) (-13°F) IS TOO LOW.
LIMIT
SEE SECTION 2.3.2.
AUTO MODE
HIGH
PREVENTS AIR EXCHANGE IN AUTO
0°C TO 30°C (27°C) MODE IF THE OUTDOOR TEMPERATURE
4
5
TEMPERATURE (32°F TO 86°F) (81°F) IS TOO HIGH.
LIMIT
SEE SECTION 2.3.2.
AU: THE SCREEN ILLUMINATES FOR 12
SECONDS WHEN ANY KEY IS PRESSED
ON: THE SCREEN IS PERMANENTLY
ILLUMINATED.
BACKLIGHT
MODE
AU / ON
AU
- 8 -
Download from Www.Somanuals.com. All Manuals Search And Download.
3. MAINTENANCE
!
WARNING
Risk of electrical shocks. Before performing any maintenance or
servicing, always disconnect the unit from its power source.
3.1 SEMI-ANNUAL MAINTENANCE (ESSENTIAL)
Your wall controller (ACCGSC1 or 40425) tells you when to perform this maintenance
when the Filter Maintenance light is flashing. Otherwise, maintenance should
be performed every 6 months to ensure your unit proper operation for years to
come. Follow these steps:
1.
2.
Turn switch knob to OFF to unlock the door.
Unlatch the door and open it. If required, the
door can be removed. To do so, remove the
stopper (A) located on the right side of the door
hinge. Then, hold the door and hit with your
palm its left side. Slide the door to the right to
disengage it from the unit. Clean the inner side
of the door with a clean damp cloth, then wipe
with a dry one.
A
VD0170
3.
Slide out the air diffuser (model GSVH1K), the heat recovery core (model
GSHH3K only), the energy recovery core (model GSEH3K only) and the
filter cartridge from the unit.
NOTES: 1. On model GSVH1K only, never grab the white shaft (item 2)
to pull out the air diffuser.
2. To remove the filter cartridge, pull on its tabs.
2
3
1
VD0091
VD0107
1) Air Diffuser
2) White shaft
3) Heat recovery core
4
5
VD0112
VD0155
4) Energy recovery core
5) Filter cartridge tabs
- 9 -
Download from Www.Somanuals.com. All Manuals Search And Download.
3. MAINTENANCE (CONT’D)
3.1 SEMI-ANNUAL MAINTENANCE (ESSENTIAL) (CONT’D)
4.
Using your thumbs, push on the prefilter side to disengage it from the filter
cartridge. Then, slide it out of the filter cartridge and discard it. Install the
new prefilter by reversing this operation.
1
2
VD0092
VD0093
1) Filter cartridge
2) Prefilter
5.
Clean the inside walls of the unit with a clean damp cloth, then wipe with a
dry one. Install the new filter cartridge.
6.1 For HEPA Filtration and Fresh Air Ventilation model GSVH1K only
Clean the air diffuser with a clean damp cloth, then wipe with a dry one. Once the
air diffuser completely dry, slide it back into the unit.
6.2 For HEPA Filtration, Fresh Air and Heat Recovery model GSHH3K only
Slide out the two core filters (item 1) from the heat
recovery core and wash them under hot water with
mild soap.
Remove the dust on the heat recovery core (item 2)
using a vacuum cleaner with a soft brush attachment.
Rinse the core filters thoroughly and let dry before
reinstalling them on the heat recovery core.
Reinstall the heat recovery core in the unit.
1
2
1
VD0091
1) Core filters
2) Heat Recovery Core
NOTE: Make sure the damper spring (1) is still
inside the left front port opening before
reinstalling the heat recovery core.
1
VD0120
1) Damper spring
- 10 -
Download from Www.Somanuals.com. All Manuals Search And Download.
3. MAINTENANCE (CONT’D)
3.1 SEMI-ANNUAL MAINTENANCE (ESSENTIAL) (CONT’D)
6.3 For HEPA Filtration, Fresh Air and Energy Recovery model GSEH3K only
CAUTION
The GSEH3K energy recovery core cannot be washed with water.
Slide out the two core filters (item 1) from the
energy recovery core and wash them under hot
1
1
water with mild soap.
Remove the dust on the energy recovery core
(item 2) using a vacuum cleaner with a soft brush
attachment.
2
Rinse the core filters thoroughly and let dry before
reinstalling them on the energy recovery core.
Reinstall the energy recovery core in the unit.
VD0155
1) Core filters
2) Energy Recovery Core
NOTE: Make sure the damper spring (1) is still
inside the left front port opening before
reinstalling the energy recovery core.
1
VD0120
1) Damper spring
7.
8.
If removed, reinstall the door and its stopper. Close the latches and turn ON
the switch knob to its previous position.
Your unit is equipped with a wall controller (ACCGSC1 or 40425). For
ACCGSC1, reset the filter maintenance indicator by inserting a small rod
(eg: paper clip end) into the reset filter hole of the wall control. Press lightly
until the Filter Maintenance indicator light turns off. For 40425, to reset the
counter and turn the LED OFF, simultaneously press both and buttons
for 1 second.
3.2 ANNUAL MAINTENANCE (ESSENTIAL)
Your unit is equipped with a wall controller (ACCGSC1 or 40425), which tells
when to perform maintenance when the Filter Maintenance light stays ON.
Otherwise, this maintenance must be performed once a year to ensure your unit
proper operation for years to come. Proceed as the Semi-annual Maintenance
(Section 3.1), but instead of replacing the prefilter (point 4), discard the complete
HEPA Filter cartridge (including prefilter). Install a new HEPA filter cartridge with
a new prefilter on it.
NOTE : In annual maintenance, for 40425, to reset the counter and turn the LED
OFF, simutaneously press both
and
buttons for 5 seconds.
- 11 -
Download from Www.Somanuals.com. All Manuals Search And Download.
3. MAINTENANCE (CONT’D)
3.3 OPTIONAL ALPINE/PINE FILTER
During pollen season, or as needed, remove the
assembled hood from its backplate by removing its 2
retaining screws.
VD0124
screw
Then, slide out the optional Alpine/pine filter and
clean it under water. Let dry before reinstalling it on the
assembled hood. Reinstall the hood on its backplate.
VA0024
- 12-
Download from Www.Somanuals.com. All Manuals Search And Download.
4. TROUBLESHOOTING
!
WARNING
Shock hazard. Never open the electronic box. No user-serviceable parts
inside. There is a fuse on the electronic board. Never attempt to replace
it. Refer servicing to qualified service personnel.
If the unit seems not working properly, call your installer or the nearest approved
Service Center. You can also reach our Customer Service Departments or
Technical Support listed below.
Broan-NuTone LLC
• Customer Service Department:
Telephone: 1-800-558-1711
Fax:
1-800-356-5862
• Technical Support:
Telephone: 1-800-637-1453
Fax:
1-262-673-8709
- 13 -
Download from Www.Somanuals.com. All Manuals Search And Download.
5. WARRANTY
WHOLE-HOUSE AIR FILTRATION SYSTEM
WARRANTY
Broan-NuTone warrants to the original consumer purchaser of its products, that
such products will be free from defects for a period of two (2) years, from date
of original purchase.
THERE ARE NO OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING,
BUT NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE. BROAN-NUTONE WILL NOT BE
HELD RESPONSIBLE FOR ANY CLAIMS OVER THE ORIGINAL PURCHASE
PRICE OF A BROAN-NUTONE WHOLE-HOUSE AIR FILTRATION SYSTEM,
NOR HELD RESPONSIBLE FOR SUBSEQUENT DAMAGE OR INCIDENT.
During the period stated above, Broan-NuTone will, at its opinion, repair or
replace, without charge, any product or part which is found to be defective
under normal use and service. THIS WARRANTY DOES NOT EXTEND TO ANY
FILTER, PREFILTER OR CORE FILTERS (IF APPLICABLE). This warranty
does not cover a) normal maintenance and service, b) any products or parts which
have been subject to misuse, negligence, accident, improper maintenance or
repairs made by other than Broan-NuTone or c) a faulty installation or installation
contrary to recommended installation instructions.
The duration of any implied warranty is limited to the 2-year period as specified
for the express warranty. Some states do not allow limitation on how long an
implied warranty lasts, so the above limitation may not apply to you.
BROAN-NUTONE’S OBLIGATION TO REPAIR OR REPLACE AT
BROAN-NUTONE’S OPTION, SHALL BE THE PURCHASER'S SOLE AND
EXCLUSIVE REMEDY UNDER THIS WARRANTY. BROAN-NUTONE SHALL NOT
BE LIABLE FOR INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES
ARISING OUT OF OR IN CONNECTION WITH PRODUCT USE OR
PERFORMANCE. SOME STATES DO NOT ALLOW THE EXCLUSION OR
LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE
ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.
This warranty gives you specific legal rights and you may also have other rights,
which vary from state to state. This warranty supersedes all prior warranties.
In order to qualify for a warranty claim, the owner of a Broan-NuTone WHOLE-HOUSE
AIR FILTRATION SYSTEM must have the model and serial number along with
a proof of the original purchase date. In each case, costs for the removal of a
defective part (and/or unit) and installation of a new or repaired one and travel
costs are not covered by this warranty.
BROAN-NUTONE LLC, 926 W. S STATE ST, HARTFORD WI 53027 1-800-637-1453
99043224
Download from Www.Somanuals.com. All Manuals Search And Download.
|